Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cell harvesting on robust smart thermosensitive pseudo-double networks prepared by one-step procedure

  • García-Sobrino, Rubén
  • García Sánchez, Carolina
  • Liz-Basteiro, Pedro
  • Reinecke, Helmut
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
  • Martínez-Campos, Enrique
  • Gallardo Ruiz, Alberto
In this work, pseudo-double networks (pseudo-DN) based on N-vinyl caprolactam (VCL, major component, precursor of thermosensitive chains) and hexyl methacrylate (HMA, minor component, hydrophobic) have been prepared by using single step approach. The adjective pseudo refers to the fact that through the simultaneous copolymerization of VCL and HMA with different relative reaction kinetics, in the presence of an appropriate mixture of crosslinkers, networks with complex structures that tend towards DN-type structures are obtained. Hydrogels have been prepared with HMA/VCL molar ratios from 0 to 23.2 mol %. The series of hydrogels prepared show a composition-dependent behaviour in terms of thermosensitivity, swelling at temperatures below the Volume Phase Transition Temperature (VPTT) value, mechanical properties and performance during the cell culture experiments. More precisely, hydrogels with low percentages of HMA show elastic moduli under compression tests slightly lower than 1 MPa and presented a high thermal response (high swelling below the VPTT) allowing in addition the non-aggressive detachment of cell monolayer by controlled decrease of temperature. As the percentage of HMA increases, the elastic modulus increases, obtaining improved mechanical properties (reaching values in the range 1–3 MPa), thermosensitivity decreases (low swelling below VPTT) and a progressive delay in cell proliferation is also observed, being still cytocompatible. In this sense, hydrogels with low percentages of HMA (up 2.7 mol %) allow cell proliferation and transplantation similar to the control sample., The authors gratefully acknowledge support from the Consejo Su- perior de Investigaciones Cientifícas (CSIC). In the same way, it is necessary to express the appreciation for funding through a Garantia Juvenil contract of the Comunidad de Madrid. Equally, this work was financially supported by the Ministerio de Ciencia, Innovación y Uni- versidades (RTI2018-096328-B-I00), by MCIN/AEI/10.13039/ 501100011033 And European Union “NextGeneration EU”/PRTR (PDC2022-133446-I00), as well as by the Instituto de Salud Carlos III (ISCIII)(PI21/00858). Support from the PTI Global Health is gratefully acknowledged. The authors would also thank the support received from the Interdisciplinary Platform for Sustainable Plastics towards a Circular Economy-Spanish National Research Council (SusPlast-CSIC), Madrid, Spain and the Interdisciplinary Platform for Additive Manufacturing (FAB3D). Finally, it is important to mention the assistance provided by Levi Lopez and Isabel Muñoz for their help in NMR and Raman characterization, respectively.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydrogels with dual sensitivity to temperature and pH in physiologically relevant ranges as supports for versatile controlled cell detachment

  • García-Sobrino, Rubén
  • Ruiz-Blas, Irene
  • García Sánchez, Carolina
  • Reinecke, Helmut
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
  • Martínez-Campos, Enrique
  • Gallardo Ruiz, Alberto
Thermosensitive hydrogels based on the N-vinyl caprolactam (VCL), capable of allowing for cell adhesion and proliferation, as well as non-aggressive detachment by controlled temperature drop, were functionalized with 23 % or lower molar percentages of the cationizable hydrophobic unit 2-(diisopropylamino) ethyl methacrylate (DPAEMA), to obtain networks with dual sensitivity to temperature and pH. The swelling analysis of the systems has shown a transition pK (pK) close to physiological values, dependent on the temperature of the medium (pK of 6.6 and 6.9 when the temperature of the medium is above and below the transition temperature VPTT, respectively) and little dependence on the degree of functionalization of DPAEMA. In addition, at temperatures below the transition temperature (VPTT), the systems have shown large swelling variations as a function of the pH (i.e. below and above the pK), exhibiting greater absorption capacity at pHs below pK, where the DPAEMA units are cationized. Cytocompatibility and transplant capacity have been evaluated using the C166-GFP endothelial cell line. None of the thermosensitive hydrogels with variable DPAEMA content showed a delay with respect to the control without DPAEMA neither in terms of adhesion nor in proliferation. However, by increasing the percentage of DPAEMA functionalization -and decreasing thermosensitivity-, a correlative decrease in mitochondrial activity was obtained in the transplant, with significant differences for the hydrogels with DPAEMA molar percentage of 3 % or higher. Taking advantage of the proximity of the pK to the physiological value, we have evaluated the cellular response and the capacity for transplantation after lowering the pH to 6.5, below pK. A direct relationship of the DPAEMA functionalization degree on the detachment efficiency was observed, since the hydrogels with the highest molar load of DPAEMA showed higher mitochondrial metabolic activity after cell detachment., he authors gratefully acknowledge support from the Consejo Su- perior de Investigaciones Cientifícas (CSIC). In the same way, it is necessary to express the appreciation for funding through a Garantia Juvenil contract of the Comunidad de Madrid. Equally, this work was financially supported by the Ministerio de Ciencia, Innovación y Uni- versidades (RTI2018-096328-B-I00), by MCIN/AEI/10.13039/ 501100011033 And European Union “NextGeneration EU”/PRTR (PDC2022-133446-I00), as well as by the Instituto de Salud Carlos III (ISCIII) (PI21/00858). Support from the PTI Global Health is gratefully acknowledged. The authors would also thank the support received from the Interdisciplinary Platform for Sustainable Plastics towards a Circular Economy-Spanish National Research Council (SusPlast-CSIC), Madrid, Spain and the Interdisciplinary Platform for Additive Manufacturing (FAB3D). Finally, it is important to mention the assistance provided by Levi Lopez and Alberto Fernandez for their help in NMR and TGA characterization, respectively, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Osteoblastic Cell Sheet Engineering Using P(VCL-HEMA)-Based Thermosensitive Hydrogels Doped with pVCL@Icariin Nanoparticles Obtained with Supercritical CO2-SAS

  • García-Sobrino, Rubén
  • Casado-Losada, Isabel
  • García Sánchez, Carolina
  • Caltagirone, Carmen
  • García-Crespo, Ana
  • Rodríguez-Hernández, Juan
  • Reinecke, Helmut
  • Gallardo, Alberto
  • Elvira, Carlos
  • Martínez-Campos, Enrique
New clinical strategies for treating severe bone and cartilage injuries are required, especially for use in combination with implant procedures. For this purpose, p(VCL-co-HEMA) thermosensitive hydrogels have been activated with icariin-loaded nanoparticles to be used as bone-cell-harvesting platforms. Supercritical CO2-SAS technology has been applied to encapsulate icariin, a small molecule that is involved in osteoblastic differentiation. Thus, physical-chemical analysis, including swelling and transmittance, showed the impact of HEMA groups in hydrogel composition. Moreover, icariin (ICA) release from p(VCL-co-HEMA) platforms, including pVCL@ICA nanoparticles, has been studied to evaluate their efficacy in relevant conditions. Finally, the thermosensitive hydrogels’ cell compatibility, transplant efficiency, and bone differentiation capacity were tested. This study identifies the optimal formulations for icariin-activated hydrogels for both control and HEMA formulations. Using this technique, osteoblastic sheets that were rich in collagen type I were successfully transplanted and recultivated, maintaining an optimal extracellular matrix (ECM) composition. These findings suggest a new cell-sheet-based therapy for bone regeneration purposes using customized and NP-activated pVCL-based cell platforms., This work was financially supported by the Ministerio de Ciencia, Innovación y Universidades (RTI2018-096328-B-I00), by MCIN/AEI/10.13039/501100011033 And European Union “NextGeneration EU”/PRTR (PDC2022-133446-I00), as well as by the Instituto de Salud Carlos III (ISCIII) (PI21/00858)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of Thermosensitive Hydrogels with Tailor-Made Geometries to Modulate Cell Harvesting of Non-Flat Cell Cultures

  • García-Sobrino, Rubén
  • Martínez Campos, Enrique
  • Marcos-Ríos, Daniel
  • Zepeda Rodríguez, Z.
  • Valentín, Juan L.
  • Sanz-Horta, Raúl
  • León-Calero, Marina
  • Reinecke, Helmut
  • Elvira, Carlos
  • Gallardo, Alberto
  • Rodríguez Hernández, Juan
Considering the complexity in terms of design that characterizes the different tissues of the human body, it is necessary to study and develop more precise therapies. In this sense, this article presents the possibility of fabricating photocurable thermosensitive hydrogels with free geometry and based on N-Vinyl Caprolactam (VCL) with the aim of modulating the adhesion of non-planar cell cultures. The fabrication process is based on the use as a mold of two-layer thick water-soluble polyvinyl alcohol (PVA) previously printed by Extrusion Material (MatEx). From this technology it has been possible to obtain hydrogels with different 3D geometries and different crosslinking percentages (2, 4 and 6 mol%). Studies have shown that networks reduce their thermosensitivity not only when the percentage of crosslinking in the formulation increases, but also when the thickness of the hydrogel obtained increases. Based on this reduction in thermosensitivity, the less crosslinked (2 mol%) hydrogels have been evaluated to carry out a novel direct application in which hydrogels with curved geometry have allowed cell adhesion and proliferation at 37 °C with the endothelial cell line C166-GFP; likewise, non-aggressive cell detachment was observed when the hydrogel temperature was reduced to values of 20 °C. Therefore, the present manuscript shows a novel application for the synthesis of free-form thermosensitive hydrogels that allows modulation of non-planar cell cultures., This work was financially supported by the Ministerio de Ciencia, Innovación y Universidades (RTI2018-096328-B-I00), by MCIN/AEI/10.13039/501100011033 and European Union “NextGeneration EU”/PRTR (PDC2022-133446-I00), as well as by the Instituto de Salud Carlos III (ISCIII) (PI21/00858)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Design of Vitrimers with Simultaneous Degradable and Dynamic Crosslinkers: Mechanical and Thermal Behavior Based on Transesterification Reactions Between β-Amino Esters and Hydroxylated Acrylate/Methacrylate Monomers

  • Ayensa, Naroa
  • Reviriego, Felipe
  • Reinecke, Helmut
  • Gallardo Ruiz, Alberto
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
In recent years, efforts have focused on developing repairable, malleable, and recyclable thermoset materials to reduce the growing volume of polymer waste and extend the lifetime of existing polymeric materials. Specifically, associative covalent adaptable networks (CANs), also known as vitrimers, have received considerable attention. In this work, photopolymerizable vitrimers were prepared by combining crosslinkers containing β-amino esters in their structure with hydroxylated acrylate or methacrylate monomers, with the aim of reprocessing these materials through the activation of transesterification reactions. The network design and photopolymerization conditions were optimized to ensure the successful formation of the vitrimers. Tunable mechanical and thermal properties were achieved by varying their chemical composition. Furthermore, the reprocessing ability of these materials was confirmed through thermal treatments. Additionally, these vitrimers exhibited the ability to undergo hydrolysis in basic aqueous media, providing an alternative pathway for recycling., The authors gratefully acknowledge support from the Consejo Superior de Investigaciones Cientifícas (CSIC). Equally, this work was financially supported by the Ministerio de Ciencia, Innovación y Universidades (RTI2018-096328-B-I00) and TED2021-130093B-C22 financed by MCIN/AEI/10.13039/501100011033 and European Union “NextGeneration EU”/PRTR (PDC2022-133446-I00), as well as by the Instituto de Salud Carlos III (ISCIII)(PI21/00858). We would like to acknowledge financial support from the PTI Susplast as well as from the Agencia Estatal de Investigación (AEI) through the project “Enhancing Circularity by Using Renewable Monomers and Sustainable Chemical Strategies of Polymer Upcycling (PLEC2021-007793)”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermosensitive hydrogels based on Poly(VCL-co-VP) loaded with carbon nanotubes for cell culture: role of the functionalization on the neural cell growth

  • Liz-Basteiro, Pedro
  • Arias-Ferreiro, Goretti
  • Marin, Davide
  • Martínez-Campos, Enrique
  • Reinecke, Helmut
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
  • Nieto-Diaz, Manuel
  • Reigada, David
  • Maza, Rodrigo M.
  • Marchesan, Silvia
  • Gallardo Ruiz, Alberto
In this study, thermosensitive hydrogels based on vinyl-lactams, loaded with multi-walled carbon nanotubes (MWCNTs, hereinafter CNTs) in a range of weight percentages up to 0.3 %, have been prepared. To optimize charge dispersion in the polymeric network matrix, CNTs have been functionalized on the one hand to facilitate dispersion in the precursor formulation, and precursor formulations containing different percentages of two types of vinyl-lactams, vinylcaprolactam (VCL) and vinylpyrrolidone (VP), have been evaluated on the other. The incorporation of functionalized CNTs increased the compressive modulus of the hydrogels more than sixfold (from ∼ 0.6 to ∼ 3.7 MPa) and improved electrical conductivity by an order of magnitude (from 8.6·10<sup>−3</sup> to 8.1·10<sup>−2</sup> S·m<sup>−1</sup>), while promoting higher rates of adhesion and proliferation of endothelial and neuronal cells. These improvements highlight the potential of the developed system for biomedical applications, such as tissue engineering and regenerative medicine., Consejo Superior de Investigaciones Científicas. Project PDC2022- 133446-I00 funded by MICIU/AEI /10.13039/501100011033, Spain, and by European Union Next GenerationEU/ PRTR. Project PID2023- 151687OB-I00 funded by MICIU/AEI/10.13039/501100011033, Spain, and by FEDER, UE., Peer reviewed