Pasar al contenido principal

PLATAFORMAS POLIMERICAS TERMOSENSIBLES PARA MANIPULACION CELULAR

RTI2018-096328-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 33
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

New Poly(Propylene Imine) Dendrimer Modified with Acridine and Its Cu(II) Complex: Synthesis, Characterization and Antimicrobial Activity

  • Bosch, Paula
  • Staneva, Desislava
  • Vasileva-Tonkova, Evgenia
  • Grozdanov, Petar
  • Nikolova, Ivanka
  • Kukeva, Rositsa
  • Stoyanova, Radostina
  • Grabchev, Ivo
A second-generation poly(propylene imine) dendrimer modified with acridine and its Cu(II) complex have been synthesized for the first time. It has been found that two copper ions form complexes with the nitrogen atoms of the dendrimeric core by coordinate bonds. The new compounds have been characterized by nuclear magnetic resonance (NMR), electron paramagnetic resonance (EPR), fourier-transform infrared spectroscopy (FTIR) and fluorescence spectroscopy. The spectral characteristics of the modified dendrimer have been measured in different organic solvents, and a negative fluorescence solvatochromism has been observed. The antimicrobial activity of the dendrimers has been tested against model pathogenic microorganisms in agar and by broth dilution method. The cotton fabric treated with both dendrimers has been evaluated towards pathogenic microorganisms. The obtained modified cotton fabrics have been shown to hamper bacterial growth and to prevent biofilm formation. Dendrimer cytotoxicity has been investigated in vitro in the model HEp-2 cell line., This research was funded by Fund “Scientific Research”, Ministry of Education and Science of Bulgaria, grant number КОСТ 01/24-2017” and “Ministry of Economy and Competitively of Spain”, grand number RTI2018-096328-B-I00. IG and PB acknowledge COST CA15114 action “Anti-MIcrobial Coating Innovations to prevent infectious diseases (AMICI)”., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Formation of responsive hierarchical wrinkled patterns on hydrogel films via multi-step methodology

  • González-Henríquez, Carmen M.
  • Rodríguez-Umanzor, F. E.
  • Guzmán, D.
  • Sarabia-Vallejos, Mauricio A.
  • Rodríguez-Hernández, Juan
In this article, a simple protocol based on a multi-step methodology is used to form flat, first-generation (G1) or second-generation (G2) wrinkled patterns. Different concentrations of DMAEMA were used to synthesize hydrogel films. The multi-step method used to form the wrinkled pattern involves vacuum, argon plasma, and UV exposure. This methodology allows creating different morphologies, which are intimately related to both the kind of treatment as well as the order employed in each case. The G1 and G2 patterns involve three essential steps. First, water removal via vacuum, generating a deswelling gradient in the films triggering the formation of a G1 pattern on top. Secondly, a frontal vitrification process was induced by argon plasma, which generates a rigid top layer, thus triggering the formation of a G2 pattern. Finally, UV irradiation for fixing the pattern. From these, we obtained the roughness, area increase percentage, undulation wavelength, and amplitude., The authors acknowledge the financial support given by FONDECYT Grant N° 1170209 and N° 3160217. To FONDEQUIP N° EQM150101 for the use of FE-SEM facilities. M.A. Sarabia acknowledges the financial support given by CONICYT through the doctoral program Scholarship Grant. J. Rodriguez-Hernandez acknowledges financial support from Ministerio de Economia y Competitividad (MINECO) (Project MAT2016-78437-R, FONDOS FEDER, and RTI2018-096328-B-I00)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fabrication of 3D-Printed Biodegradable Porous Scaffolds Combining Multi-Material Fused Deposition Modeling and Supercritical CO2 Techniques

  • Sanz-Horta, Raúl
  • Elvira, Carlos
  • Gallardo Ruiz, Alberto
  • Reinecke, Helmut
  • Rodríguez-Hernández, Juan
© 2020 by the authors., The fabrication of porous materials for tissue engineering applications in a straightforward manner is still a current challenge. Herein, by combining the advantages of two conventional methodologies with additive manufacturing, well-defined objects with internal and external porosity were produced. First of all, multi-material fused deposition modeling (FDM) allowed us to prepare structures combining poly (ε-caprolactone) (PCL) and poly (lactic acid) (PLA), thus enabling to finely tune the final mechanical properties of the printed part with modulus and strain at break varying from values observed for pure PCL (modulus 200 MPa, strain at break 1700%) and PLA (modulus 1.2 GPa and strain at break 5–7%). More interestingly, supercritical CO2 (SCCO2) as well as the breath figures mechanism (BFs) were additionally employed to produce internal (pore diameters 80–300 µm) and external pores (with sizes ranging between 2 and 12 μm) exclusively in those areas where PCL is present. This strategy will offer unique possibilities to fabricate intricate structures combining the advantages of additive manufacturing (AM) in terms of flexibility and versatility and those provided by the SCCO2 and BFs to finely tune the formation of porous structures., This research was funded by Ministerio de Ciencia, Innovación y Universidades (MAT2013-42957-R, Project MAT2016-78437-R, FONDOS FEDER, RTI2018-096328-B-I00) and Comunidad de Madrid project Biopieltec-CM S2018/BAA-4480., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Biocompatible fluorinated wrinkled hydrogel films with antimicrobial activity

  • González-Henríquez, Carmen M.
  • Rodríguez-Umanzor, F. E.
  • Almagro-Correa, J.
  • Sarabia-Vallejos, Mauricio A.
  • Martínez-Campos, Enrique
  • Esteban-Lucía, M.
  • Campo, Ángel Adolfo del
  • Rodríguez-Hernández, Juan
Surface-modified hydrogel films were designed to control the bacterial colonization on their surface and to promote cell proliferation through the gradual insertion of highly hydrophobic functional monomers. These hydrogel films were deposited via spin-coating technique, using muscovite mica as a substrate. These samples were then exposed to different external stimuli to produce wrinkled patterns. The relationship between the monomers which compose the hydrogel, was varied to alter the hydrophobic/hydrophilic balance of the final composite. Contact angle and confocal Raman spectroscopy measurements were carried out to characterize the surface and the bulk of the hydrogel film. Cell proliferation and antimicrobial tests were performed using premyoblastic murine cells (C2C12-GFP) and RAW 264.7 (ATCC® TIB-71) macrophagic cell lines, and also for bacteria strains, Staphylococcus aureus and Escherichia coli. The results indicate that the inclusion of the TFPMA produces an increase in cell proliferation, together with a decrease in living bacterial colonies after 48 h, both for Gram-positive or Gram-negative species., The authors acknowledge the financial support given by FONDECYT Grant N° 1170209 and FONDEQUIP N° EQM150101 for the use of FESEM facilities. M.A. Sarabia acknowledges the financial support provided by CONICYT through the doctoral program Scholarship Grant. J. Rodriguez-Hernandez acknowledges financial support from Ministerio de Economia y Competitividad (MINECO) (Project MAT2016-78437-R, FONDOS FEDER, and RTI2018-096328-B-I00).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

pKa Modulation of Pyrrolidine-Based Catalytic Polymers Used for the Preparation of Glycosyl Hydrazides at Physiological pH and Temperature

  • Vargas, E. L.
  • Velázquez, J. A.
  • Rodrigo, Eduardo
  • Reinecke, Helmut
  • Rodríguez-Hernández, Juan
  • Fernández-Mayoralas, Alfonso
  • Gallardo Ruiz, Alberto
  • Cid, M. Belén
Inspired by the ability of enzymes to use the surrounding hydrophobic and/or polarizable groups to modulate the pK of a given amino acid, we designed a series of soluble polymers able to decrease the basicity of pyrrolidine (from 11.2 to 8.6 pK units), which clearly increases its aminocatalytic activity at physiological pH in C═N bond formation reactions via ion iminium activation. Other parameters such as charge density, hydrophobic/hydrophilic balance, and aggregation state have been studied as important factors in the catalytic activity of the polymers for a given substrate. To demonstrate the utility of our approach, an optimal pyrrolidine-based catalytic polymer has been used for the formation of C-N bonds between hydrazides and free sugars as the model system for the preparation of glycoconjugates., We thank the undergraduate student Elena Y. García for some preliminary experiments and Laura Lagartera Ortiz for her help with the Isothermal Titration Calorimetry (ITC) experiments. E. L. Vargas thanks the University of Costa Rica for a PhD scholarship. We acknowledge the Spanish Government (CTQ2016-78779-R, RTI2018-096328-B-I00, and MAT2015-65184-C2-2-R) for financial support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Innovative procedure for precise deposition of wrinkled hydrogel films using direct inkjet printing

  • González-Henríquez, Carmen M.
  • Rodríguez-Umanzor, F. E.
  • Sarabia-Vallejos, Mauricio A.
  • Terraza, Claudio A.
  • Martínez-Campos, Enrique
  • Rodríguez-Hernández, Juan
This manuscript presents an inkjet-based strategy to fabricate wrinkled hydrogel surfaces with controlled characteristics (period and amplitude). For this purpose, a monomer mixture containing a crosslinking agent, a hydrophilic monomer, and a photoinitiator were deposited onto polycarbonate substrates. Upon UV irradiation and controlled drying under a vacuum atmosphere, either one-generation or hierarchical two-generation wrinkles were formed. More interestingly, the wrinkle characteristics depend on the crosslinking agent and monomer concentration in the solution so that larger wrinkles were observed in diluted solutions. Equally, the wrinkle period and amplitude also gradually grow by increasing the number of deposited layers. Atomic force microscopy was carried out to finely characterize the wrinkle dimensions as well as their eventual preferential orientation and distribution. Besides, hydrogel surfaces have been evaluated in terms of cytocompatibility, given their potential interest for biomedical applications., The authors acknowledge the financial support given by FONDECYT Grant No. 1170209 and FONDEQUIP No. EQM150101 for the use of FESEM facilities. M.A. Sarabia acknowledges the financial support provided by CONICYT through the doctoral program Scholarship Grant. J. Rodriguez-Hernandez acknowledges financial support from Ministerio de Ciencia, Innovación y Universidades (Project MAT2016-78437-R, FONDOS FEDER, and RTI2018-096328-B-I00)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Breath figures makes porous the “so-called” skin layer obtained in polymer foams prepared by supercritical CO2 treatments

  • Sanz-Horta, Raúl
  • Martínez-Campos, Enrique
  • García Sánchez, Carolina
  • Reinecke, Helmut
  • Gallardo Ruiz, Alberto
  • Rodríguez-Hernández, Juan
  • Elvira, Carlos
In this article, the preparation of porous polymeric scaffolds of the synthetic poly (isopropylideneglycerol methacrylate) (PIPGMA) is described combining two complementary techniques. Supercritical CO (SCCO), has been used as foaming agent to obtain internal porosity by varying parameters such as pressure and depressurization time. However, the disadvantage of SCCO technology is the formation of a non-porous skin layer described in the majority of the samples. This skin layer was modified by the breath figures technique (BF), providing superficial porosity to the polymeric sample. The result of using both techniques subsequently showed the formation of a porous network throughout the samples with inner and outer pores interconnected, characterized by scanning electron microscopy (SEM), micro X-ray computerized tomography scanning (micro CT), and processing those images with Image J. Finally, preliminary biological evaluation of the porous samples has been carried out in order to evaluate the biocompatibility and cellular viability of these scaffolds., We gratefully acknowledge financial support from the Consejo Superior de Investigaciones Científicas (CSIC) and the Ministerio de Ciencia, Innovación y Universidades (MINECO) grant num-ber MAT2013-42957-R, and MAT2016-78437-R (FONDOS FEDER),RTI2018-096328-B-I00, and to Comunidad de Madrid project Biopieltec-CM S2018/BAA-4480.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Amino-functionalized zirconium and cerium MOFs: Catalysts for visible light induced aerobic oxidation of benzylic alcohols and microwaves assisted N-Alkylation of amines

  • Valverde-Gónzález, Antonio
  • Pintado-Sierra, Mercedes
  • Rasero-Almansa, Antonia M.
  • Sánchez, Félix
  • Iglesias, Marta
Herein we report that mixed zirconium-cerium-MOFs with amino-functionalized linkers (2-amino-1,4-benzenedicarboxylate, BDC-NH, and 4-aminonaphthalene-2,6-dicarboxylate, NDC-NH) act as effective non-noble-metal-based heterogeneous catalysts, for both the aerobic photooxidation of benzylic alcohols and for the direct microwaves activation N-alkylation of amines with alcohols. The catalytic performance has been studied considering two different approaches: the effect of NH functionalized linkers and the effect of hosting Ce species on Zr-MOFs. Zr- and ZrCe-MOFs resulted efficient visible-light-driven photocatalysts with high stability and considerable recyclability in the photocatalytic selective oxidation of alcohols to aldehydes using molecular oxygen as oxidant. These materials are also effective catalysts for the microwaves-assisted N-alkylation of amines with alcohols yielding selectively the imine (ZrCe-MOF) or the corresponding secondary amine (Ce-MOFs)., Authors acknowledge to MINECO of SpainMAT2017-82288-C2-2-P project for financial support. A.V.G. thanks Ministerio de Educación y Formación Profesional for FPU17/03463. M.P.S thanks to MINECO of Spain for RTI2018-096328-B-I00 project
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hybrid functionalized coatings on Metallic Biomaterials for Tissue Engineering

  • Santos-Coquillat, A.
  • Martínez-Campos, Enrique
  • Mora Sánchez, H.
  • Moreno Capellán, Laura
  • Arrabal, R.
  • Mohedano, M.
  • Gallardo Ruiz, Alberto
  • Rodríguez-Hernández, Juan
  • Matykina, E.
The review encompasses state-of-the-art strategies for design and fabrication of smart biomaterials for tissue engineering. The focus of the work is mainly put on metallic biomaterials with hybrid coatings consisting of bioceramic and polymeric layers with hierarchical organization and drug-eluting capacity. Key technologies and steps to design hybrid smart and multifunctional coatings on metallic cores for bone regeneration implants and cardiovascular stents are outlined, including additive manufacturing of titanium and magnesium alloys for permanent and temporary implant applications. Three levels of hierarchical surface functionalization are described: i) in situ modification of the core material, incorporating bioactive inorganic species and phases by means of ceramic coatings via anodic electrochemical treatments; ii) post-treatment application of polymer layers, monolithic or with specific porous breath figure topography; and iii) application of a cellular therapy component (single cell or cell sheet). Recent progress in incorporation of drug-eluting functionality into such materials via direct or nanocarrier-assisted loading is also highlighted., The authors gratefully acknowledge the support of the RTI2018- 096391-B-C33 (MCIU/AEI/FEDER, UE) and ADITIMAT-CM (S2018/ NMT-4411) projects. M. Mohedano and H. Mora-S ́anchez are grateful for the support of RYC-2017 21843 and PEJD-2019-POST/IND-16119, respectively. A. Santos-Coquillat is grateful for financial support from Ministerio de Ciencia e Innovación, Instituto de Salud Carlos III Sara Borrell Fellowship CD19/00136. Equally, this work was financially supported by the Ministerio de Ciencia e Innovación (RTI2018-096328- B-I00).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermoresponsive microwrinkled hydrogel surfaces with modulated chemical composition

  • González-Henríquez, Carmen M.
  • Medel-Molina, G. E.
  • Rodríguez-Umanzor, F. E.
  • Terraza Inostroza, C.
  • Sarabia-Vallejos, Mauricio A.
  • Rodríguez-Hernández, Juan
Smart wrinkled hydrogel patterns with modulated chemical composition and wrinkle characteristics (amplitude and period) were formed by taking advantage of surface instabilities using a simple, cost-affordable, and robust method. The microstructured surfaces were prepared by dip coating and were designed to be stimuli-responsive by introducing poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) in the initial feed. For this purpose, a silylated substrate surface serves as an anchor for the non-polymerized hydrogel molecules, thus forming a homogenous and reproducible coating. Once the film was achieved, the samples were exposed to vacuum and UV irradiation to form wrinkled patterns spontaneously. The response of the thermosensitive wrinkles reveals significant variations in the properties of the wrinkled films depending on the temperature. In addition to the simplicity, this deposition strategy allows the preparation of highly reproducible films using an easy-scalable methodology with potential interest for industrial applications., The authors acknowledge the financial support given by FONDECYT Grant N◦ 1170209. J. Rodriguez-Hernandez acknowledges financial support from Ministerio de Ciencia, Innovación y Universidades (Project RTI2018-096328-B-I00). Finally, this study was funded by VRAC Grant Number LPR20-03 and L318-02 of Universidad Tecnológica Metropolitana.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Wrinkling on stimuli-responsive functional polymer surfaces as a promising strategy for the preparation of effective antibacterial/antibiofouling surfaces

  • González-Henríquez, Carmen M.
  • Rodríguez-Umanzor, F. E.
  • Alegría-Gómez, M. N.
  • Terraza-Inostroza, C. A.
  • Martínez-Campos, Enrique
  • Cue-López, Raquel
  • Sarabia-Vallejos, Mauricio A.
  • García-Herrera, C.
  • Rodríguez-Hernández, Juan
Biocompatible smart interfaces play a crucial role in biomedical or tissue engineering applications, where their ability to actively change their conformation or physico-chemical properties permits finely tuning their surface attributes. Polyelectrolytes, such as acrylic acid, are a particular type of smart polymers that present pH responsiveness. This work aims to fabricate stable hydrogel films with reversible pH responsiveness that could spontaneously form wrinkled surface patterns. For this purpose, the photosensitive reaction mixtures were deposited via spin-coating over functionalized glasses. Following vacuum, UV, or either plasma treatments, it is possible to spontaneously form wrinkles, which could increase cell adherence. The pH responsiveness of the material was evaluated, observing an abrupt variation in the film thickness as a function of the environmental pH. Moreover, the presence of the carboxylic acid functional groups at the interface was evidenced by analyzing the adsorption/desorption capacity using methylene blue as a cationic dye model. The results demonstrated that increasing the acrylic acid in the microwrinkled hydrogel effectively improved the adsorption and release capacity and the ability of the carboxylic groups to establish ionic interactions with methylene blue. Finally, the role of the acrylic acid groups and the surface topography (smooth or wrinkled) on the final antibacterial properties were investigated, demonstrating their efficacy against both gram-positive and gram-negative bacteria model strains (E. coli and S. Aureus). According to our findings, microwrinkled hydrogels presented excellent antibacterial properties improving the results obtained for planar (smooth) hydrogels., This research was funded by FONDECYT Grant N◦ 1170209. Thanks to FONDEQUIP N◦ EQM150101 for the use of FE-SEM facilities. J. Rodriguez-Hernandez acknowledges financial support from Ministerio de Ciencia, Innovación y Universidades (Project RTI2018-096328-B-I00). C.M. Gonzalez-Henriquez also acknowledges project L318-02 (UTEM) “Concurso de Fortalecimiento para Equipamiento Científico y Tecnológico, Convocatoria 2018” for plasma exposure system acquisition. M.A. Sarabia and C. García-Herrera acknowledge the financial support given by Universidad de Santiago de Chile through Project DICYT 052116GH_POSTDOC. Finally, this study was funded by VRAC Grant Number LPR20-03 and L318-02 of Universidad Tecnológica Metropolitana
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermosensitive hydrogels functionalized with pH sensitive COOH groups for bone cell harvesting

  • García-Sobrino, Rubén
  • Casado-Losada, I.
  • Bruno-Pérez, L.
  • García Sánchez, Carolina
  • Reinecke, Helmut
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
  • Gallardo Ruiz, Alberto
  • Martínez-Campos, Enrique
Vinyl-caprolactam based thermosensitive hydrogel films, capable of detach cell monolayers in a non-aggressive manner upon decrease of temperature, were functionalized with carboxylic groups at different molar percentages ranging from 1 up to 12%. This functionalization was carried out by a bottom-up approach incorporating methacrylic acid (MAA) to the photo-polymerization reaction. Incorporation of MAA led to hydrogels with dual sensitivity to temperature and pH. While the functionalization has shown to have a small influence on the transition temperature, the carboxylic load plays a key role on the water uptake at these two conditions, i.e. at temperatures and pHs both above or both below transition values. A C2C12-GFP mouse muscle premyoblastic cell line was used to comparatively study cell cytocompatibility and cell detachment capability. Although all hydrogels have shown to be cytocompatible, the carboxylic group has shown, for MAA molar contents higher than 5% and in a composition-dependent manner, a negative influence on the early cell adhesion, as well as on the comparative number of detached cells. Finally, MC3T3-E1 mouse preosteoblastic cell line was studied to both analyze cell harvesting and bone differentiation processes by studying collagen secretion and calcium deposits formation. Up-regulation of collagen secretion and matrix mineralization was observed for the samples with the highest MAA content, showing that MAA functionalization successfully improved bone matrix synthesis., The authors gratefully acknowledge support from the Consejo Su- perior de Investigaciones Cientifícas (CSIC). In the same way, it is necessary to express the appreciation for funding through to Garantia Juvenil contract of the Comunidad de Madrid. Equally, this work was financially supported by the Ministerio de Ciencia, Innovación y Uni- versidades (RTI2018-096328-B-I00).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Innovation in Additive Manufacturing Using Polymers: A Survey on the Technological and Material Developments

  • Sarabia-Vallejos, Mauricio A.
  • Rodríguez-Umanzor, F. E.
  • González-Henríquez, Carmen M.
  • Rodríguez-Hernández, Juan
This review summarizes the most recent advances from technological and physico-chem-ical perspectives to improve several remaining issues in polymeric materials’ additive manufacturing (AM). Without a doubt, AM is experimenting with significant progress due to technological innovations that are currently advancing. In this context, the state-of-the-art considers both research areas as working separately and contributing to developing the different AM technologies. First, AM techniques’ advantages and current limitations are analyzed and discussed. A detailed overview of the efforts made to improve the two most extensively employed techniques, i.e., material extrusion and VAT-photopolymerization, is presented. Aspects such as the part size, the possibility of producing parts in a continuous process, the improvement of the fabrication time, the reduction of the use of supports, and the fabrication of components using more than one material are ana-lyzed. The last part of this review complements these technological advances with a general overview of the innovations made from a material perspective. The use of reinforced polymers, the preparation of adapted high-temperature materials, or even the fabrication of metallic and ceramic parts using polymers as supports are considered. Finally, the use of smart materials that enable the fabrication of shape-changing 3D objects and sustainable materials will also be explored., The authors recognize the financial support given by FONDECYT Grant No. 1170209 and No. 1220251. M.A. Sarabia-Vallejos acknowledges financial support from Universidad San Sebastián (USS) via its project No. VRID FAI 21/17. J. Rodriguez-Hernandez acknowledges financial support from Ministerio de Ciencia, Innovación y Universidades (Project MAT2016-78437-R, FONDOS FEDER, and RTI2018-096328-B-I00). Finally, we would like to thank the PIT FAB3D, PTI + Salud Gobal and the PTI + SUSPLAST from CSIC for their support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Pyrrolidine-based catalytic microporous polymers in sustainable C[dbnd]N and C[dbnd]C bond formation via iminium and enamine activation

  • Vargas, E. L.
  • Esteban, Noelia
  • Cencerrero, J.
  • Francés, V.
  • Álvarez, Cristina
  • Miguel, Jesús A.
  • Gallardo Ruiz, Alberto
  • Lozano López, Ángel Emilio
  • Cid, M. B.
A new set of catalytic materials having a pyrrolidine moiety confined in microporous organic polymer networks (POPs) has been attained. These catalytic polymers have been prepared by a straightforward synthesis starting from microporous polymer networks made from isatin (or a mixture of isatin and trifluoroacetophenone) and 1,3,5-triphenylbenzene. The polymers efficiently catalyzed the formation of nitrones under very mild and sustainable conditions using green solvents through an iminium ion activation mechanism. The reactions are scalable, and polymers are easily recycled. Special attention has been paid to understanding all the factors that could affect the efficiency of the confined catalysts. The electronic and conformational characteristics of the pyrrolidine moiety attached to the porous polymers, as well as other features that could affect the transport through the network, such as molecular volume and shape of reactants and products, and even hydrophilic or hydrophobic properties, have been systematically evaluated. In addition, the heterogeneous polymers are also useful in C[dbnd]C bond formation through both iminium ion and enamine activation., We acknowledge the Spanish Government (Agencia Estatal de Investigación projects; CTQ2016-78779-R, PID2019-109403RB-C22, RTI2018-096328-B-I00, CTQ2017-89217-P and PID2020-118547GB- I00), and the Regional Government of Castilla y León (project CyL and EU-FEDER program VA224P20), for financial support. E. L. Vargas thanks University of Costa Rica for a PhD scholarship. We must thank Rebecca Chevillard and Valentina Petrelli for some preliminary experiments., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Micropatterned functional interfaces on elastic substrates fabricated by fixing out of plane deformations

  • Nogales, Aurora
  • García Sánchez, Carolina
  • Campo, Ángel Adolfo del
  • Ezquerra, Tiberio A.
  • Rodríguez-Hernández, Juan
We report on the preparation of micropatterned functional surfaces produced by inducing an out-of-plane deformation on elastic substrates and fixing these by creating a rigid oxidized top layer. Specifically, the elastic substrate used was Polydimethylsiloxane (PDMS) and the rigid layer on top was created by ozonation of this material. We evidenced that the surface pattern formed is directly dependent on the pressure applied, the mechanical properties of the elastic substrate and on the dimensions and shape of the mask employed to define the exposed and non-exposed areas. In addition to the pattern formed, another interesting aspect is related to the ozone diffusion within the material. Softer PDMS enables more efficient diffusion and produced a thicker oxidized layer in comparison to rigid PDMS. Finally, a simulation was carried out using the distribution of Von Misses stresses of a solid plate to understand the conditions in which the applied force resulted in the rupture of the rigid oxidized layer under a permanent deformation., The authors gratefully acknowledge support from the Consejo Superior de Investigaciones Científicas (CSIC). Equally, this work was financially supported by the Ministerio de Ciencia e Innovación (MICINN) (Grants RTI2018-096328-B-I00 and PID2019-107514GB-I00/AEI/10.13039/501100011033).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fabrication and Testing of Multi-Hierarchical Porous Scaffolds Designed for Bone Regeneration via Additive Manufacturing Processes

  • González-Henríquez, Carmen M.
  • Rodríguez-Umanzor, F. E.
  • Acuña-Ruiz, N.F.
  • Vera-Rojas, G.E.
  • Terraza-Inostroza, C. A.
  • Cohn-Inostroza, N.A.
  • Utrera, A.
  • Sarabia-Vallejos, Mauricio A.
  • Rodríguez-Hernández, Juan
Bone implants or replacements are very scarce due to the low donor availability and the high rate of body rejection. For this reason, tissue engineering strategies have been developed as alternative solutions to this problem. This research sought to create a cellular scaffold with an intricate and complex network of interconnected pores and microchannels using salt leaching and additive manufacturing (3D printing) methods that mimic the hierarchical internal structure of the bone. A biocompatible hydrogel film (based on poly-ethylene glycol) was used to cover the surface of different polymeric scaffolds. This thin film was then exposed to various stimuli to spontaneously form wrinkled micropatterns, with the aim of increasing the contact area and the material’s biocompatibility. The main innovation of this study was to include these wrinkled micropatterns on the surface of the scaffold by taking advantage of thin polymer film surface instabilities. On the other hand, salt and nano-hydroxyapatite (nHA) particles were included in the polymeric matrix to create a modified filament for 3D printing. The printed part was leached to eliminate porogen particles, leaving homogenously distributed pores on the structure. The pores have a mean size of 26.4 ± 9.9 μm, resulting in a global scaffold porosity of ~42% (including pores and microchannels). The presence of nHA particles, which display a homogeneous distribution according to the FE-SEM and EDX results, have a slight influence on the mechanical resistance of the material, but incredibly, despite being a bioactive compound for bone cells, did not show a significant increase in cell viability on the scaffold surface. However, the synergistic effect between the presence of the hydrogel and the pores on the material does produce an increase in cell viability compared to the control sample and the bare PCL material., The authors recognize the financial support given by FONDECYT Grant No. 1170209, No.1220251, and No. 1200329. M.A. Sarabia-Vallejos acknowledges financial support from Universidad San Sebastián (USS) via project No. VRID FAI 21/17. J. Rodriguez-Hernandez acknowledges financial support from Ministerio de Ciencia, Innovación y Universidades (Project MAT2016-78437-R, FONDOS FEDER, and RTI2018-096328-B-I00). We would like to thank the PIT FAB3D, PTI + Salud Global, and the PTI + SUSPLAST from CSIC for their support. Thanks to the MINEDUC-UTM 1999 project that acquired the FE-SEM in the UTEM. The authors also acknowledge the support of ANIDthrough FONDEQUIP project EQM 130028, which enabled micro-CT image acquisitions. Finally, this study was funded by VRAC Grant Number LPR20-03 and L318-02 of Universidad Tecnológica Metropolitana.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Quasi-in vivo corrosion behavior of AZ31B Mg alloy with hybrid MWCNTs-PEO/PCL based coatings

  • Daavari, Morteza
  • Atapour, Masoud
  • Mohedano, Marta
  • Mora Sánchez, Hugo
  • Rodríguez-Hernández, Juan
  • Matykina, Endzhe
  • Arrabal, Raúl
  • Taherizadeh, Aboozar
This study investigated the effects of multi-walled carbon nanotubes (MWCNTs) and polycaprolactone (PCL) on the quasi-in vivo corrosion behavior of AZ31B Mg alloy treated by plasma electrolytic oxidation (PEO). Thin (∼2 µm, PCTPCL4) and thick (∼60 µm, PCTPCL6) PCL layers were applied only onto the MWCNTs-PEO coating (PCT) as it showed better corrosion performance. Findings reveal that incorporation of MWCNTs induced several structural and functional modifications in the PEO coating, such as increased roughness, a thicker inner barrier layer, and reduced hydrophilicity. Quasi-in vivo corrosion testing was carried out under controlled temperature, pH, and fluid flow in simulated body fluid (SBF) by electrochemical impedance spectroscopy (EIS) and hydrogen evolution experiments. EIS results revealed that, after 48 h immersion, a diffusion process controlled hydration of the ceramic coatings. Comparison of the collected hydrogen after 15 days of immersion in the quasi-in vivo environment revealed that the PEO and PCT ceramic coatings decreased hydrogen generation by up to 74% and 91%, respectively, compared to non-coated alloy. PCTPCL6 coating exhibited the lowest amount of collected hydrogen (0.2 mL/cm). The thick PCL layer delayed the onset of substrate corrosion for at least 120 h, reducing the corrosion rate by 85% compared with the PCT., The authors gratefully acknowledge the financial support of the Iran National Science Foundation INSF (Grant No. 97014179). This work was also supported by RTI2018–096391-B-C33 (MCIU/AEI/FEDER, UE) and S2018/NMT-4411 (Regional government of Madrid and EU Structural and Social Funds). M. Mohedano is grateful for the support of RYC-2017–21843. We also gratefully acknowledge financial support from the Spanish National Science Foundation (CSIC) and the Ministerio de Ciencia, Innovación y Universidades (MINECO) grant number RTI2018–096328-B-I00. The technical support from Dr. Mariona Cabero during the preparation of TEM cross-section specimens is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Biopolímeros: oportunidades y desafíos para la impresión 3D

  • Relinque, José Javier
  • Rodríguez Hernández, Juan
La aplicación de polímeros de origen biológico en impresión 3D, así como su implementación en distintos sectores como el aeroespacial, textil, alimentario o biomédico es un campo de gran interés, no solo desde el punto de vista de la investigación académica sino desde la perspectiva ambiental y social. En este artículo se revisará la fabricación aditiva de biopolímeros, haciendo especial énfasis en una selección de materiales: celulosa, lignina, alginato, quitosano, ácido poliláctico y policaprolactona., Usage of biological polymers in 3D printing, as well as their implementation in different sectors such like aerospace, textile, food industry or biomedicine is a field of keen interest, not only under the point of view of the academic research, but from an environmental and social concern. In this article it will be gone over additive manufacturing of biopolymers, highlighting a variety of materials, namely, cellulose, lignin, alginate, chitosan, starch, polylactic acid, and polycaprolactone., Los autores agradecen el apoyo del Consejo Superior de Investigaciones Científicas (CSIC). Igualmente, este trabajo contó con el apoyo del Ministerio de Economía y Competitividad (MINECO) (Proyecto RTI2018-096328-B-I00) y de las plataformas temáticas interdisciplinares SUSPLAST+ y FAB3D. En particular, José Javier Relinque desea agradecer su vinculación contractual postdoctoral con financiación nacional Margarita Salas-Universidad de Cádiz 2021, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Fabrication of 3D cylindrical thermosensitive hydrogels as supports for cell culture and detachment of tubular cell sheets

  • García-Sobrino, Rubén
  • Lago, E.
  • Goñi, C.
  • Ramos, Viviana
  • García Sánchez, Carolina
  • Reinecke, Helmut
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
  • Gallardo, Alberto
  • Martínez-Campos, Enrique
Pseudo interpenetrating vinyl-caprolactam (VCL) based thermosensitive tubular hydrogels with a volume phase transition temperature, VPTT, around 35 °C, have been prepared by combining two different crosslinkers, a di-methacrylate (C1) and a di-vinyl urea (C2). The molar ratio between the two crosslinkers (for a global crosslinker molar percentage of 1.9) has shown to play a key role on the properties of the hydrogel. Increasing the amount of di-vinyl urea, leads to transparent but rather fragile materials and to a lower extent of thermosensitivity, that is, to a lower variation in the hydrogel swelling upon temperature change. However, tubes prepared with a selected crosslinker molar ratio C1/C2 of 65/35 provided a compromise between transparency, thermosensitivity and maneuverability and were, thus, evaluated as supports for cell culture using premyoblastic cells. These hydrogels, used as supports, allow for surface adhesion and cell proliferation until confluence, and eventually an efficient monolayer detachment (and transplant to a 3D-printed polylactic acid (PLA) support) through a controlled drop in temperature. As a result, this method permits to obtain tubular tissue constructs with potential applications in tissue engineering such as in the elaboration of vascular grafts., The authors gratefully acknowledge support from the Consejo Superior de Investigaciones Científicas (CSIC). In the same way, it is necessary to express the appreciation for funding through a Garantia Juvenil contract of the Comunidad de Madrid. Equally, this work was financially supported by the Ministerio de Ciencia, Innovacion y Universidades (RTI2018-096328-B-I00). We are grateful to Carlota Blasco for some preliminary experiments., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ciprofloxacin Release and Corrosion Behaviour of a Hybrid PEO/PCL Coating on Mg3Zn0.4Ca Alloy

  • Moreno, L.
  • Wang, Cheng
  • Lamaka, Sviatlana L.
  • Zheludkevich, M. L.
  • Rodríguez-Hernández, Juan
  • Arrabal, Raúl
  • Matykina, Endzhe
In the present work, a hybrid hierarchical coating (HHC) system comprising a plasma electrolytic oxidation (PEO) coating and a homogeneously porous structured polycaprolactone (PCL) top-coat layer, loaded with ciprofloxacin (CIP), was developed on Mg3Zn0.4Ca alloy. According to the findings, the HHC system avoided burst release and ensured gradual drug elution (64% over 240 h). The multi-level protection of the magnesium alloy is achieved through sealing of the PEO coating pores by the polymer layer and the inhibiting effect of CIP (up to 74%). The corrosion inhibition effect of HHC and the eluted drug is associated with the formation of insoluble CIP-Me (Mg/Ca) chelates that repair the defects in the HHC and impede the access of corrosive species as corroborated by FTIR spectra, EIS and SEM images after 24 h of immersion. Therefore, CIP participates in an active protection mechanism by interacting with cations coming through the damaged coating., The authors gratefully acknowledge the support of the ADITIMAT-CM (S2018/NMT-4411, the Regional Government of Madrid and EU Structural Funds), PID2021-124341OB-C22 and RTI2018-096328-B-I00 (MICINN/AEI/FEDER, UE) projects. Mr. Cheng Wang thanks the China Scholarship Council for the award of fellowship and funding No. 201806310128. Finally, we thank the PIT FAB3D, PTI + Salud Global, and the PTI + SUSPLAST from CSIC for their support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Smart Polymer Surfaces with Complex Wrinkled Patterns: Reversible, Non-Planar, Gradient, and Hierarchical Structures

  • Sarabia-Vallejos, Mauricio A.
  • Cerda-Iglesias, Felipe E.
  • Pérez-Monje, Dan A.
  • Acuña-Ruiz, N.F.
  • Terraza-Inostroza, C. A.
  • Rodríguez-Hernández, Juan
  • González-Henríquez, Carmen M.
This review summarizes the relevant developments in preparing wrinkled structures with variable characteristics. These include the formation of smart interfaces with reversible wrinkle formation, the construction of wrinkles in non-planar supports, or, more interestingly, the development of complex hierarchically structured wrinkled patterns. Smart wrinkled surfaces obtained using light-responsive, pH-responsive, temperature-responsive, and electromagnetic-responsive polymers are thoroughly described. These systems control the formation of wrinkles in particular surface positions and the reversible construction of planar-wrinkled surfaces. This know-how of non-planar substrates has been recently extended to other structures, thus forming wrinkled patterns on solid, hollow spheres, cylinders, and cylindrical tubes. Finally, this bibliographic analysis also presents some illustrative examples of the potential of wrinkle formation to create more complex patterns, including gradient structures and hierarchically multiscale-ordered wrinkles. The orientation and the wrinkle characteristics (amplitude and period) can also be modulated according to the requested application., The authors recognize the financial support from FONDECYT Grant N◦ 1220251 and N◦ 11230427. M.A. Sarabia-Vallejos acknowledges financial support from Universidad San Sebastián (USS) via project No. VRID FAI 21/17. J. Rodriguez-Hernandez acknowledges financial support from Ministerio de Ciencia, Innovación y Universidades (Project MAT2016-78437-R, FONDOS FEDER, and RTI2018-096328-B-I00). Finally, we thank the PIT FAB3D, PTI + Salud Global, and the PTI + SUSPLAST from CSIC for their support, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Vat Photopolymerization 3D Printing of Hydrogels with Re-Adjustable Swelling

  • Liz-Basteiro, Pedro
  • Reviriego, Felipe
  • Martínez-Campos, Enrique
  • Reinecke, Helmut
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
  • Gallardo Ruiz, Alberto
Vat photopolymerization typically prints highly crosslinked networks. Printing hydrogels, which are also networks but with a high swelling capacity in water and therefore with low crosslinking density, is a challenge for this technique. However, it may be of interest in medicine and in other areas, since it would allow for the preparation of this type of 3D-shaped material. In this work, an approach for printing hydrogels via vat photopolymerization that uses a mixture of stable and hydrolysable crosslinkers has been evaluated so that an initial highly crosslinked network can be printed, although after hydrolysis it becomes a network with low crosslinking. This approach has been studied with PEO/PEG-related formulations, that is, with a PEG-dimethacrylate as a stable crosslinker, a PEO-related derivative carrying β-aminoesters as a degradable crosslinker, and PEG-methyl ether acrylate and hydroxyethyl acrylate as monofunctional monomers. A wide family of formulations has been studied, maintaining the weight percentage of the crosslinkers at 15%. Resins have been studied in terms of viscosity, and the printing process has been evaluated through the generation of Jacobs working curves. It has been shown that this approach allows for the printing of pieces of different shapes and sizes via vat photopolymerization, and that these pieces can re-ajust their water content in a tailored fashion through treatments in different media (PBS or pH 10 buffer)., This research was funded by the Ministerio de Ciencia, Innovación y Universidades (RTI2018-096328-B-I00). P.L.-B. also appreciates the funding from the Ministerio de Ciencia, Innovación y Universidades (PRE2019-090285, co-financed by the European Social Fund, ESF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Clear polyurethane coatings with excellent virucidal properties: Preparation, characterization and rapid inactivation of human coronaviruses 229E and SARS-CoV-2

  • Salgado, Cástor
  • Cue-López, Raquel
  • Yuste, Vanesa
  • Montalvillo-Jiménez, Laura
  • Prendes, Pilar
  • Paz, S.
  • Vázquez-Calvo, Ángela
  • Alcamí, Antonio
  • García Sánchez, Carolina
  • Martínez-Campos, Enrique
  • Bosch, Paula
Commercial polyurethane (PU) coating formulations have been modified with 1-(hydroxymethyl)-5,5-dimethylhydantoin (HMD) both in bulk (0.5 and 1% w/w) and onto the coatings surface as an N-halamine precursor, to obtain clear coatings with high virucidal activity. Upon immersion in diluted chlorine bleaching, the hydantoin structure on the grafted PU membranes was transformed into N-halamine groups, with a high surface chlorine concentration (40-43μg/cm). Fourier transform infrared spectroscopy (FTIR) spectroscopy, thermogravimetric analysis (TGA), energy-dispersive X-ray (EDX), X-ray photoelectron spectroscopy (XPS) and iodometric titration were used to characterize the coatings and quantify the chlorine contents of the PU membranes after chlorination. Biological evaluation of their activity against Staphylococcus aureus (Gram-positive bacteria) and human coronaviruses HCoV-229E and SARS-CoV-2 was performed, and high inactivation of these pathogens was observed after short contact times. The inactivation of HCoV-229E was higher than 98% for all modified samples after just 30 minutes, whereas it was necessary 12 hours of contact time for complete inactivation of SARS-CoV-2. The coatings were fully rechargeable by immersion in diluted chlorine bleach (2% v/v) for at least 5 chlorination-dechlorination cycles. Moreover, the performance of the antivirus efficiency of the coatings is considered as long-lasting, because experiments of reinfection of the coatings with HCoV-229E coronavirus did not show any loss of the virucidal activity after three consecutive infection cycles without reactivation of the N-halamine groups., This work was funded by Spanish National Research Council project CSIC-COVID19-119, European Union (Nextgeneration EU), CSIC Interdisciplinary Thematic Platform Salud Global+ (PTI-SALUDGLOBAL+) and MICINN (RTI2018-096328-B-I00). We thank Isabel Sola, Luis Enjuanes and Volker Thiel for providing us with viruses, cells and scientific advice; and Rocío Martín for her excellent technica, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

High resolution molds, sacrificial in aqueous media, obtained by vat photopolymerization 3D printing

  • Liz-Basteiro, Pedro
  • Sanz-Horta, Raúl
  • Reviriego, Felipe
  • Martínez-Campos, Enrique
  • Reinecke, Helmut
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
  • Gallardo, Alberto
From the synthesis of two methacrylic crosslinkers that contain in their structure β-amino esters activated for hydrolysis, photocurable formulations for vat photopolymerization have been prepared, in order to obtain sacrificial parts in aqueous media. Starting from binary formulations of both crosslinkers with the monofunctional monomer poly (ethylene glycol) methyl ether acrylate (PEGMEA), its printability has been demonstrated, as well as the sacrificial nature of the printed parts. Selecting a crosslinker weight percentage of 15%, optimization of the mechanical properties of the printed parts has been carried out through a variation of the formulation components, combining the crosslinker with 1 or 2 monofunctional monomers chosen from 2-hydroxy ethyl acrylate (HEA), PEGMEA, methacrylic acid (MAA) and 2-carboxyethyl acrylate (CEA), in different proportions. All the formulations were printable, and have allowed for modulating the mechanical properties of the printed parts, in terms of rigidity/flexibility and resistance. All printed parts have been shown to be sacrificial in basic water. Finally, a proof of concept has been carried out for its possible use as sacrificial molds, to obtain screws from a thermoplastic poly (ε-caprolactone) and from a silicone network, obtained respectively by heating and chemical crosslinking, followed by solubilisation in aqueous media., The authors gratefully acknowledge support from the Consejo Su- perior de Investigaciones Científicas (CSIC). Equally, this work was financially supported by the Ministerio de Ciencia, Innovación y Uni- versidades (RTI2018-096328-B-I00). PL-B also appreciates the funding from the Ministerio de Ciencia, Innovación y Universidades (PRE2019- 090285, co-financed by the European Social Fund ESF)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of Biocompatible Digital Light Processing Resins for Additive Manufacturing Using Visible Light-Induced RAFT Polymerization

  • Sarabia-Vallejos, Mauricio A.
  • Romero de la Fuente, Scarleth
  • Tapia, Pamela
  • Cohn-Inostroza, N.A.
  • Estrada, Manuel
  • Ortiz-Puerta, David
  • Rodríguez-Hernández, Juan
  • González-Henríquez, Carmen M.
Patients with bone diseases often experience increased bone fragility. When bone injuries exceed the body’s natural healing capacity, they become significant obstacles. The global rise in the aging population and the escalating obesity pandemic are anticipated to lead to a notable increase in acute bone injuries in the coming years. Our research developed a novel DLP resin for 3D printing, utilizing poly(ethylene glycol diacrylate) (PEGDA) and various monomers through the PET-RAFT polymerization method. To enhance the performance of bone scaffolds, triply periodic minimal surfaces (TPMS) were incorporated into the printed structure, promoting porosity and pore interconnectivity without reducing the mechanical resistance of the printed piece. The gyroid TPMS structure was the one that showed the highest mechanical resistance (0.94 ± 0.117 and 1.66 ± 0.240 MPa) for both variants of resin composition. Additionally, bioactive particles were introduced to enhance the material’s biocompatibility, showcasing the potential for incorporating active compounds for specific applications. The inclusion of bioceramic particles produces an increase of 13% in bioactivity signal for osteogenic differentiation (alkaline phosphatase essay) compared to that of control resins. Our findings highlight the substantial improvement in printing precision and resolution achieved by including the photoabsorber, Rose Bengal, in the synthesized resin. This enhancement allows for creating intricately detailed and accurately defined 3D-printed parts. Furthermore, the TPMS gyroid structure significantly enhances the material’s mechanical resistance, while including bioactive compounds significantly boosts the polymeric resin’s biocompatibility and bioactivity (osteogenic differentiation)., The authors acknowledge the financial support provided by FONDECYT (Grant Numbers: 1220251 and 11230427), FONDEF IDeA I+D (ID23I10110), and ANID-Millennium Science Initiative Program (ICN2021_004). J. Rodriguez-Hernandez acknowledges financial support from Ministerio de Ciencia, Innovación y Universidades (Project: RTI2018-096328-B-I00). We thank the PIT FAB3D, PTI + Salud Global, and the PTI + SUSPLAST from CSIC for their support. We thank the MINEDUC-UTM 1999 project that helped acquire the FE-SEM for the UTEM. Esta publicación contó con el apoyo de la Vicerrectoría de Investigación y Doctorados de la Universidad San Sebastián–Fondo USS-FIN-24-APCS-02., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cell harvesting on robust smart thermosensitive pseudo-double networks prepared by one-step procedure

  • García-Sobrino, Rubén
  • García Sánchez, Carolina
  • Liz-Basteiro, Pedro
  • Reinecke, Helmut
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
  • Martínez-Campos, Enrique
  • Gallardo Ruiz, Alberto
In this work, pseudo-double networks (pseudo-DN) based on N-vinyl caprolactam (VCL, major component, precursor of thermosensitive chains) and hexyl methacrylate (HMA, minor component, hydrophobic) have been prepared by using single step approach. The adjective pseudo refers to the fact that through the simultaneous copolymerization of VCL and HMA with different relative reaction kinetics, in the presence of an appropriate mixture of crosslinkers, networks with complex structures that tend towards DN-type structures are obtained. Hydrogels have been prepared with HMA/VCL molar ratios from 0 to 23.2 mol %. The series of hydrogels prepared show a composition-dependent behaviour in terms of thermosensitivity, swelling at temperatures below the Volume Phase Transition Temperature (VPTT) value, mechanical properties and performance during the cell culture experiments. More precisely, hydrogels with low percentages of HMA show elastic moduli under compression tests slightly lower than 1 MPa and presented a high thermal response (high swelling below the VPTT) allowing in addition the non-aggressive detachment of cell monolayer by controlled decrease of temperature. As the percentage of HMA increases, the elastic modulus increases, obtaining improved mechanical properties (reaching values in the range 1–3 MPa), thermosensitivity decreases (low swelling below VPTT) and a progressive delay in cell proliferation is also observed, being still cytocompatible. In this sense, hydrogels with low percentages of HMA (up 2.7 mol %) allow cell proliferation and transplantation similar to the control sample., The authors gratefully acknowledge support from the Consejo Su- perior de Investigaciones Cientifícas (CSIC). In the same way, it is necessary to express the appreciation for funding through a Garantia Juvenil contract of the Comunidad de Madrid. Equally, this work was financially supported by the Ministerio de Ciencia, Innovación y Uni- versidades (RTI2018-096328-B-I00), by MCIN/AEI/10.13039/ 501100011033 And European Union “NextGeneration EU”/PRTR (PDC2022-133446-I00), as well as by the Instituto de Salud Carlos III (ISCIII)(PI21/00858). Support from the PTI Global Health is gratefully acknowledged. The authors would also thank the support received from the Interdisciplinary Platform for Sustainable Plastics towards a Circular Economy-Spanish National Research Council (SusPlast-CSIC), Madrid, Spain and the Interdisciplinary Platform for Additive Manufacturing (FAB3D). Finally, it is important to mention the assistance provided by Levi Lopez and Isabel Muñoz for their help in NMR and Raman characterization, respectively.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Hydrogels with dual sensitivity to temperature and pH in physiologically relevant ranges as supports for versatile controlled cell detachment

  • García-Sobrino, Rubén
  • Ruiz-Blas, Irene
  • García Sánchez, Carolina
  • Reinecke, Helmut
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
  • Martínez-Campos, Enrique
  • Gallardo Ruiz, Alberto
Thermosensitive hydrogels based on the N-vinyl caprolactam (VCL), capable of allowing for cell adhesion and proliferation, as well as non-aggressive detachment by controlled temperature drop, were functionalized with 23 % or lower molar percentages of the cationizable hydrophobic unit 2-(diisopropylamino) ethyl methacrylate (DPAEMA), to obtain networks with dual sensitivity to temperature and pH. The swelling analysis of the systems has shown a transition pK (pK) close to physiological values, dependent on the temperature of the medium (pK of 6.6 and 6.9 when the temperature of the medium is above and below the transition temperature VPTT, respectively) and little dependence on the degree of functionalization of DPAEMA. In addition, at temperatures below the transition temperature (VPTT), the systems have shown large swelling variations as a function of the pH (i.e. below and above the pK), exhibiting greater absorption capacity at pHs below pK, where the DPAEMA units are cationized. Cytocompatibility and transplant capacity have been evaluated using the C166-GFP endothelial cell line. None of the thermosensitive hydrogels with variable DPAEMA content showed a delay with respect to the control without DPAEMA neither in terms of adhesion nor in proliferation. However, by increasing the percentage of DPAEMA functionalization -and decreasing thermosensitivity-, a correlative decrease in mitochondrial activity was obtained in the transplant, with significant differences for the hydrogels with DPAEMA molar percentage of 3 % or higher. Taking advantage of the proximity of the pK to the physiological value, we have evaluated the cellular response and the capacity for transplantation after lowering the pH to 6.5, below pK. A direct relationship of the DPAEMA functionalization degree on the detachment efficiency was observed, since the hydrogels with the highest molar load of DPAEMA showed higher mitochondrial metabolic activity after cell detachment., he authors gratefully acknowledge support from the Consejo Su- perior de Investigaciones Cientifícas (CSIC). In the same way, it is necessary to express the appreciation for funding through a Garantia Juvenil contract of the Comunidad de Madrid. Equally, this work was financially supported by the Ministerio de Ciencia, Innovación y Uni- versidades (RTI2018-096328-B-I00), by MCIN/AEI/10.13039/ 501100011033 And European Union “NextGeneration EU”/PRTR (PDC2022-133446-I00), as well as by the Instituto de Salud Carlos III (ISCIII) (PI21/00858). Support from the PTI Global Health is gratefully acknowledged. The authors would also thank the support received from the Interdisciplinary Platform for Sustainable Plastics towards a Circular Economy-Spanish National Research Council (SusPlast-CSIC), Madrid, Spain and the Interdisciplinary Platform for Additive Manufacturing (FAB3D). Finally, it is important to mention the assistance provided by Levi Lopez and Alberto Fernandez for their help in NMR and TGA characterization, respectively, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Biocompatible and bioactive PEG-Based resin development for additive manufacturing of hierarchical porous bone scaffolds

  • Sarabia-Vallejos, Mauricio A.
  • Cerda-Iglesias, Felipe E.
  • Terraza, C.A
  • Cohn-Inostroza, NicolÁs A.
  • Utrera, Andrés
  • Estrada, Manuel
  • Rodríguez-Hernández, Juan
  • González-Henríquez, Carmen M.
Bone diseases can often result in patient bone fragility. Different bone problems include low bone density, osteoporosis, and other bone diseases. Such bone diseases, ailments, and malfunctions often require complex and expensive treatments. In this study, we synthesized a new type of DLP resin for 3D printing purposes based on poly(ethylene glycol diacrylate) (PEGDA) and acrylic acid (AAc). In addition, using a porogen within the pho- topolymerizable resin allowed us to fabricate hierarchical interconnected porous structures. These structures combine the pores resulting from the CAD design with those obtained by the lixiviation of the porogen. Finally, bioactive particles were added to the mixture to increase the material’s biocompatibility, thus proving the strategy’s potential to include active compounds for particular purposes. Our results demonstrate that including the photoabsorber, Orange G, considerably increases the printing precision and resolution of the synthesized resin, making it possible to obtain printed parts with intricate and complex geometries with high accuracy and definition. Nano-hydroxyapatite (nHA) inclusion significantly increases the material’s biocompatibility and mechanical stiffness (~47 % increase, from 5.47 MPa to 8.02 MPa)., he authors acknowledge the financial support given by FONDECYT Grant N◦ 1220251, N◦ 1230090, and N◦ 11230427. J. Rodriguez- Hernandez acknowledges financial support from Ministerio de Ciencia, Innovación y Universidades (ProjectRTI2018-096328-B-I00). We thank the PIT FAB3D, PTI + Salud Global, and the PTI + SUSPLAST from CSIC for their support. Thanks to the MINEDUC-UTM 1999 project that ac- quired the FE-SEM in the UTEM. The authors also acknowledge the support of ANID through the FONDEQUIP project EQM 130028, which enabled micro-CT image acquisitions. Finally, this study was funded by Project Supported by the Competition for Research Regular Projects, year 2020, code LPR20-03, Universidad Tecnológica Metropolitana, and he APC of this research was funded by ANID-Chile through the InES Género Project INGE210029 (ANID+InES Género+INGE210029)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Osteoblastic Cell Sheet Engineering Using P(VCL-HEMA)-Based Thermosensitive Hydrogels Doped with pVCL@Icariin Nanoparticles Obtained with Supercritical CO2-SAS

  • García-Sobrino, Rubén
  • Casado-Losada, Isabel
  • García Sánchez, Carolina
  • Caltagirone, Carmen
  • García-Crespo, Ana
  • Rodríguez-Hernández, Juan
  • Reinecke, Helmut
  • Gallardo, Alberto
  • Elvira, Carlos
  • Martínez-Campos, Enrique
New clinical strategies for treating severe bone and cartilage injuries are required, especially for use in combination with implant procedures. For this purpose, p(VCL-co-HEMA) thermosensitive hydrogels have been activated with icariin-loaded nanoparticles to be used as bone-cell-harvesting platforms. Supercritical CO2-SAS technology has been applied to encapsulate icariin, a small molecule that is involved in osteoblastic differentiation. Thus, physical-chemical analysis, including swelling and transmittance, showed the impact of HEMA groups in hydrogel composition. Moreover, icariin (ICA) release from p(VCL-co-HEMA) platforms, including pVCL@ICA nanoparticles, has been studied to evaluate their efficacy in relevant conditions. Finally, the thermosensitive hydrogels’ cell compatibility, transplant efficiency, and bone differentiation capacity were tested. This study identifies the optimal formulations for icariin-activated hydrogels for both control and HEMA formulations. Using this technique, osteoblastic sheets that were rich in collagen type I were successfully transplanted and recultivated, maintaining an optimal extracellular matrix (ECM) composition. These findings suggest a new cell-sheet-based therapy for bone regeneration purposes using customized and NP-activated pVCL-based cell platforms., This work was financially supported by the Ministerio de Ciencia, Innovación y Universidades (RTI2018-096328-B-I00), by MCIN/AEI/10.13039/501100011033 And European Union “NextGeneration EU”/PRTR (PDC2022-133446-I00), as well as by the Instituto de Salud Carlos III (ISCIII) (PI21/00858)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of Thermosensitive Hydrogels with Tailor-Made Geometries to Modulate Cell Harvesting of Non-Flat Cell Cultures

  • García-Sobrino, Rubén
  • Martínez Campos, Enrique
  • Marcos-Ríos, Daniel
  • Zepeda Rodríguez, Z.
  • Valentín, Juan L.
  • Sanz-Horta, Raúl
  • León-Calero, Marina
  • Reinecke, Helmut
  • Elvira, Carlos
  • Gallardo, Alberto
  • Rodríguez Hernández, Juan
Considering the complexity in terms of design that characterizes the different tissues of the human body, it is necessary to study and develop more precise therapies. In this sense, this article presents the possibility of fabricating photocurable thermosensitive hydrogels with free geometry and based on N-Vinyl Caprolactam (VCL) with the aim of modulating the adhesion of non-planar cell cultures. The fabrication process is based on the use as a mold of two-layer thick water-soluble polyvinyl alcohol (PVA) previously printed by Extrusion Material (MatEx). From this technology it has been possible to obtain hydrogels with different 3D geometries and different crosslinking percentages (2, 4 and 6 mol%). Studies have shown that networks reduce their thermosensitivity not only when the percentage of crosslinking in the formulation increases, but also when the thickness of the hydrogel obtained increases. Based on this reduction in thermosensitivity, the less crosslinked (2 mol%) hydrogels have been evaluated to carry out a novel direct application in which hydrogels with curved geometry have allowed cell adhesion and proliferation at 37 °C with the endothelial cell line C166-GFP; likewise, non-aggressive cell detachment was observed when the hydrogel temperature was reduced to values of 20 °C. Therefore, the present manuscript shows a novel application for the synthesis of free-form thermosensitive hydrogels that allows modulation of non-planar cell cultures., This work was financially supported by the Ministerio de Ciencia, Innovación y Universidades (RTI2018-096328-B-I00), by MCIN/AEI/10.13039/501100011033 and European Union “NextGeneration EU”/PRTR (PDC2022-133446-I00), as well as by the Instituto de Salud Carlos III (ISCIII) (PI21/00858)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Development of Soft Wrinkled Micropatterns on the Surface of 3D-Printed Hydrogel-Based Scaffolds via High-Resolution Digital Light Processing

  • Sarabia-Vallejos, M. A.
  • Romero De la Fuente, S.
  • Cohn-Inostroza, N. A.
  • Terraza, C. A.
  • Rodríguez-Hernández, Juan
  • González-Henríquez, C. M.
The preparation of sophisticated hierarchically structured and cytocompatible hydrogel scaffolds is presented. For this purpose, a photosensitive resin was developed, printability was evaluated, and the optimal conditions for 3D printing were investigated. The design and fabrication by additive manufacturing of tailor-made porous scaffolds were combined with the formation of surface wrinkled micropatterns. This enabled the combination of micrometer-sized channels (100–200 microns) with microstructured wrinkled surfaces (1–3 μm wavelength). The internal pore structure was found to play a critical role in the mechanical properties. More precisely, the TPMS structure with a zero local curvature appears to be an excellent candidate for maintaining its mechanical resistance to compression stress, thus retaining its structural integrity upon large uniaxial deformations up to 70%. Finally, the washing conditions selected enabled us to produce noncytotoxic materials, as evidenced by experiments using AlamarBlue to follow the metabolic activity of the cells., The authors acknowledge the financial support provided by FONDECYT (grant numbers: 1220251 and 11230427) and FONDEF IDeA I+D (ID23I10110). J. Rodriguez-Hernandez acknowledges financial support from Ministerio de Ciencia, Innovación y Universidades (Project: RTI2018-096328- B-I00) and PIT FAB3D, PTI + Salud Global, and the PTI + SUSPLAST from CSIC for their support. We thank the MINEDUC-UTM 1999 project that helped to acquire the FE-SEM for the UTEM. Also, the APC of this research manuscript was funded by ANID-Chile through the InES Género Project INGE210029 (ANID+InES Género+INGE210029)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Incorporation of Water-Soluble Quantum Dots and Formation of Wrinkled Patterns on Acrylic and Silicone Elastomers

  • Guzmán-De La Cerda, Diego
  • Jofré-Ulloa, Pedro Pablo
  • Benavente, Eglantina
  • González-Henríquez, Carmen
  • Celis, Freddy
  • Rodríguez-Hernández, Juan
  • Martínez-Campos, Enrique
  • Vera-Rojas, Gloria
  • Melo-Sanguinetti, Juan Pablo
n this article, poly(dimethylsiloxane) (PDMS) and VHB4910 (AR) elastomers are used to fabricate nanocomposites with quantum dots (QDs) of two different sizes (2.77 nm (Q2) and 4.21 nm, Q9). QDs are synthesized in an aqueous medium, with control of their size by the reflux time. The elastomer hydrophobicity is adjusted by (i) ultraviolet–ozone (UVO) treatment and (ii) functionalization with 3-aminopropyl-trimethoxysilane (APTMS, 10% v/v). The obtained elastomers are submerged in QD solution and sonicated for 24 h. The presence of QDs on the modified surface is confirmed by scanning electron microscopy–energy-dispersive spectroscopy (SEM–EDS). The Raman spectroscopy characterization shows an amide functional group at 1500–1570 cm–1, confirming the covalent binding of the QDs with the APTMS. As a result of the modification, wrinkled patterns are observed on the modified elastomers, formed by a swelling-induced mechanism (PDMS) and a mechanical stretching/compression (AR). The nanocomposites display emission peaks akin to QDs in solution (521.0–579.0 nm for Q2, 531.5–585.5 nm for PDMS-nanocomposites, and 537.0–597.5 nm for AR-nanocomposites) and lifetime averages between 1.09 and 2.18 ns, confirming the obtaining of nanocomposites with desired optical properties., The authors acknowledge the financial support given by CONICYT through Project ANID PAI No. 77190086, Millennium Institute on Green Ammonia as Energy Vector MIGA ICN2021_023, FONDECYT Regular No.1170209, FONDECYT Regular No. 1151189, Ministerio de Ciencia e Innovación-Spain (RTI2018-096328-B-100). The authors also acknowledge the FONDEQUIP program EQM150020., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Design of Vitrimers with Simultaneous Degradable and Dynamic Crosslinkers: Mechanical and Thermal Behavior Based on Transesterification Reactions Between β-Amino Esters and Hydroxylated Acrylate/Methacrylate Monomers

  • Ayensa, Naroa
  • Reviriego, Felipe
  • Reinecke, Helmut
  • Gallardo Ruiz, Alberto
  • Elvira, Carlos
  • Rodríguez-Hernández, Juan
In recent years, efforts have focused on developing repairable, malleable, and recyclable thermoset materials to reduce the growing volume of polymer waste and extend the lifetime of existing polymeric materials. Specifically, associative covalent adaptable networks (CANs), also known as vitrimers, have received considerable attention. In this work, photopolymerizable vitrimers were prepared by combining crosslinkers containing β-amino esters in their structure with hydroxylated acrylate or methacrylate monomers, with the aim of reprocessing these materials through the activation of transesterification reactions. The network design and photopolymerization conditions were optimized to ensure the successful formation of the vitrimers. Tunable mechanical and thermal properties were achieved by varying their chemical composition. Furthermore, the reprocessing ability of these materials was confirmed through thermal treatments. Additionally, these vitrimers exhibited the ability to undergo hydrolysis in basic aqueous media, providing an alternative pathway for recycling., The authors gratefully acknowledge support from the Consejo Superior de Investigaciones Cientifícas (CSIC). Equally, this work was financially supported by the Ministerio de Ciencia, Innovación y Universidades (RTI2018-096328-B-I00) and TED2021-130093B-C22 financed by MCIN/AEI/10.13039/501100011033 and European Union “NextGeneration EU”/PRTR (PDC2022-133446-I00), as well as by the Instituto de Salud Carlos III (ISCIII)(PI21/00858). We would like to acknowledge financial support from the PTI Susplast as well as from the Agencia Estatal de Investigación (AEI) through the project “Enhancing Circularity by Using Renewable Monomers and Sustainable Chemical Strategies of Polymer Upcycling (PLEC2021-007793)”., Peer reviewed