Pasar al contenido principal

DESARROLLO DE NANOFLUIDOS PARA INTERCAMBIADORES DE CALOR EN LA INDUSTRIA RENOVABLE GEOTERMICA

PID2020-112846RB-C21

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE VIGO

Resultados relacionados

Resultados totales (Incluyendo duplicados): 21
Encontrada(s) 1 página(s)

Minerva. Repositorio Institucional de la Universidad de Santiago de Compostela
Publicación Artículo científico (JournalArticle)

Improving tribological efficiency of isopropyl palmitate oil with cellulose nanocrystals: a sustainable approach for high-performance lubricants

  • García Guimarey, María Jesús
  • Marcos, Marco A.
  • Vallejo, Javier P.
  • Viesca, José L.
  • Pérez Comuñas, María José
  • Lugo, Luis
  • Hernández Battez, Antolín
This article explores the potential of cellulose nanocrystals (CNCs) as a lubricant additive for isopropyl palmitate (IPP) oil to enhance its tribological performance. CNCs, derived from renewable sources, offer a sustainable and environmentally friendly alternative to traditional lubricant additives. A two-step method was used to prepare the nanolubricants, with visual control and dynamic light scattering measurements to assess their temporal stability. The viscous behavior of the nanolubricants, in terms of viscosity and viscosity index, was evaluated at different temperatures. The study assesses the effectiveness of CNC/IPP oil blends as lubricants through tribological tests, including evaluations under pure sliding and rolling–sliding conditions. Studies on worn surfaces were conducted using surface roughness analysis, Raman mapping, and XPS, and the thermal stability was examined to determine their suitability for different operating conditions. CNCs significantly reduce friction by up to 44% and improve wear resistance compared to the neat IPP base oil, presumably due to a self-repairing effect. Furthermore, an improvement of the thermal conductivity of pure IPP base oil has been revealed with increasing CNC concentration. This study enhances the understanding of cellulose nanocrystals as lubricant additives and their potential to transform traditional lubricating oils into high-performance and sustainable solutions.
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Phase change characterization of eco-friendly isopropyl palmitate-based graphene nanoplatelet nanofluid for thermal energy applications

  • Iglesias Prado, José Ignacio
  • Calviño Barreiro, Uxía
  • Lugo Latas, Luis
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, Thermal energy storage (TES) facilitates the integration of renewable energy by decoupling production and consumption, mitigating intermittence issues. However, current TES systems use fossil fuel-based products as storage media, so the development of sustainable and efficient materials should be investigated. This work aims to the design and characterization of new eco-friendly nanoenhanced phase change materials (NePCMs) based on dispersions of graphene nanoplatelets of two different lateral sizes (7.2 and 40 μm) in isopropyl palmitate for cold storage applications. The stability of the NePCMs was analysed by dynamic light scattering, selecting Span® 80 as surfactant to improve the stabilization of both nanomaterials within the base material. The influence of the nanoadditive concentration on the temperature transitions and on the solid–liquid phase change were comprehensively studied by differential scanning calorimetry, finding out that the dispersed nanoadditives do not alter the polymorphism of the isopropyl palmitate. Additionally, reductions in the sub-cooling effect higher than 2 K for both nanoplatelets were found, with increases in the latent heat up to 5.9 and 3.9% for the shorter and the longer nanoplatelets, respectively. Isobaric heat capacities were also determined by temperature-modulated differential scanning calorimetry, reporting maximum reductions of 12% compared to the base material., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, Agencia Estatal de Investigación | Ref. ENE2017-86425-C2-1-R, Xunta de Galicia | Ref. ED481A-2018/287, Xunta de Galicia | Ref. ED431C 2020/06, Xunta de Galicia | Ref. ED481A-2021/284
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Thermophysical and electrical properties of ethylene glycol-based nanofluids containing CaCO3

  • Traciak, Julian
  • Cabaleiro Álvarez, David
  • Vallejo, Javier P.
  • Fal, Jacek
The thermophysical properties of various types of nanofluids are often studied to find more effective working fluids for heat transfer applications. In this paper, the mass density, isobaric heat capacity, thermal conductivity, dynamic viscosity surface tension, and electrical properties of calcium carbonate-ethylene glycol (CaCO3-EG) nanofluids were investigated. The samples with mass fractions of 0.01, 0.02, and 0.03 were prepared with a two-step method and studied as well as pure base fluid (ethylene glycol). The measurements were conducted at temperatures between 283.15 and 313.15 K and the obtained results show the impact of CaCO3 nanoparticles on the thermophysical and electrical properties of ethylene glycol., Agencia Estatal de Inestigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Inestigación | Ref. IJC2020-043779-I
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Dependence of thermal conductivity on size and specific surface area for different based CoFe2O4 cluster nanofluids

  • Pérez Vallejo, Javier
  • Elsaidy , Amir Hassan Abdelrahman
  • Lugo Latas, Luis
Enhancing the thermal conductivity of fluids by using nanoparticles with outstanding thermophysical properties has acquired significant attention for heat-transfer applications. Nanofluids have the potential to optimize energy systems by improving heat-transfer efficiency. In this study, cobalt ferrite nanoparticles clusters with controlled mean sizes ranging from 97 to 192 nm were synthesized using a solvothermal method to develop novel nanofluids with enhanced thermal conductivity. These clusters were comprehensively characterized using transmission electron microscopy, X-ray diffraction, Raman spectroscopy, vibrating-sample magnetometry, and nitrogen physisorption. The CoFe2O4 cluster nanofluids were prepared using the two-step method with various base fluids (water, propylene glycol, and a mixture of both). Dynamic light scattering analyses of the average Z-size of the dispersed nanoadditives over time revealed that the stability of the dispersions is influenced by cluster size and the proportion of glycol in the base fluid. The thermal conductivity of the base fluid and nine different 0.5 wt% CoFe2O4 cluster nanofluids was measured using the transient hot wire method at temperatures of 293.15, 303.15, and 313.15 K, showing different temperature dependencies. The study also explores the relationships between the thermal conductivity, cluster size, and specific surface area of the nanoadditives. A maximum thermal conductivity enhancement of 4.2% was reported for the 0.5 wt% nanofluid based on propylene glycol containing 97 nm CoFe2O4 clusters. The findings suggest that the specific surface area of nanostructures is a more relevant parameter than size for describing improvements in thermal conductivity., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Preparation and characterization of stable methyl myristate−in−water nanoemulsions as advanced working fluids for cooling systems

  • Cabaleiro Álvarez, David
  • Hermida Merino, Carolina
  • Losada Barreiro, Sonia
  • Agresti, F.
  • Lugo Latas, Luis
  • Hermida Merino, Daniel
  • Piñeiro, M.M.
Phase change material emulsions (PCME) have gained increasing scientific interest due to their potential to enhance the storage capability of thermal facilities. Herein we present the design and characterization of oil−in−water (O/W) nanoemulsions by employing a dispersed phase mixture (2–12 wt%) enriched in methyl myristate as phase change material. The emulsifier and dispersed phase compositions were optimized based on dynamic light scattering and calorimetric analyses. A two−surfactant formulation composed of sodium dodecyl sulfate and BrijTM S2 (20:49 in weight) was selected to produce stable colloidal dispersions of a methyl stearate:n–hexadecane:methyl myristate mixture (at a mass proportion of 1:3:36) in water. No phase separation or significant growth in emulsified droplet size was detected under storage conditions or when the slurries were subjected to different heating−cooling cycles. The melting/crystallization transitions, rheological behavior, thermal conductivity and density of optimized nanoemulsions were experimentally investigated in order to further understand how the concentration and physical state of suspended droplets may influence those thermal and physical properties. According to differential scanning calorimetry studies, slurries showed moderate subcooling degrees (∼3 °C), even though their solid−liquid transitions extended over a slightly wider range of temperatures than the same mixture used as the dispersed phase but in bulk−form. The shear−thinning character observed for developed nanoemulsions at low temperatures disappeared with the melting of suspended droplets. Considering an operating temperature interval of 15 °C around melting−crystallization phase changes, the 12 wt% optimized suspension presented a storage capacity 18 % higher than that of water under the same conditions. Furthermore, thermal reliability tests verified that phase change characteristics did not significantly changed after 8 months of storage and throughout 500 thermal cycles., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PID2022-136443OB-I00, Agencia Estatal de Investigación | Ref. IJC2020-043779-I
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

A new relationship on transport properties of nanofluids. Evidence with novel magnesium oxide based n-tetradecane nanodispersions

  • Iglesias Prado, José Ignacio
  • Pérez Vallejo, Javier
  • Lugo Latas, Luis
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, The worldwide increasing of thermal energy consumption fosters new technological solutions based on nanomaterials. The use of nanofluids enhances energy efficiency leading to eco-friendlier devices. Thus, researchers are encouraged to understand how modified thermophysical properties improve heat transfer capability. Magnesium oxide based n-tetradecane nanofluids are designed in terms of stability for cold storage application. Thermal conductivity, viscosity, density, and isobaric heat capacity were determined by transient hot wire, rotational rheometry, mechanical oscillation U-tube, and differential scanning calorimetry. Furthermore, a useful relationship on thermal conductivity and viscosity of nanofluids is proposed based on Andrade, Osida and Mohanty theories. Its reliability is checked with the here reported results and literature data of different nanofluids: titanium oxide within water, silver within poly(ethylene glycol), and aluminium oxide within (1-ethyl-3-methylimidazolium methanesulfonate + water). Similar trends have been found for all nanofluids excepting titanium oxide aqueous nanofluids, this differentiated behaviour being expected by the proposed relationship., Agencia Estatal de Investigación | Ref. ENE2017-86425-C2-1-R, Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, Xunta de Galicia | Ref. ED431C 2020/06, Xunta de Galicia | Ref. ED481A-2018/287
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Tuning the thermal properties of aqueous nanofluids by taking advantage of size-customized clusters of iron oxide nanoparticles

  • Elsaidy , Amir Hassan Abdelrahman
  • Pérez Vallejo, Javier
  • Salgueiriño Maceira, Verónica
  • Lugo Latas, Luis
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, In this study, the thermal conductivity of aqueous nanofluids containing clusters of iron oxide (Fe3O4/γ-Fe2O3) nanoparticles has been investigated experimentally for the first time, with the aim of assessing the role of a controlled aggregation of nanoparticles in these final nanofluids. For that, clusters of iron oxide nanoparticles of different cluster size (46–240 nm diameter range) were synthesized by a solvothermal method and fully characterized by transmission electron microscopy, X-ray diffraction and Raman spectroscopy. The rheological behavior of the optimal nanofluids was also studied by rotational rheometry. The nanofluids were obtained by dispersing the clusters of iron oxide nanoparticles in water taking into account different solid volume fractions (from 0.50 to 1.5 wt%) and the experiments were conducted in the temperature range from 293.15 K to 313.15 K. The study reveals and quantifies enhancements in the thermal conductivity of nanofluid with increase of cluster size and temperature. Furthermore, a 0.50 wt% concentration of clusters of iron oxide nanoparticles within the whole range of proposed nanofluids offers great stability and improved thermal conductivity for heat transfer applications with an small dynamic viscosity increase. In addition, the larger the size of the clusters of iron oxide nanoparticles, the greater the increase in thermal conductivity for the designed Fe3O4/γ-Fe2O3 cluster-based nanofluids, with thermal conductivity values following a constant upward trend and reaching a maximum increase of 4.4% for the largest synthesized clusters (average size of 240 nm). These results open the door for the development of iron oxide-based nanofluids on which taking advantage of an optimized aggregation of nanoparticles by using size-customized clusters, Ministerio de Economía y Competitividad | Ref. ENE2017-86425-C2-1-R, Ministerio de Economía y Competitividad | Ref. CTM2017-84050-R, Ministerio de Ciencia e Innovación | Ref. PID2020-112846RB-C21, Ministerio de Ciencia e Innovación | Ref. PID2020-119242RB-I00, Ministerio de Ciencia e Innovación | Ref. PDC2021-121225-C21
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Thermal and rheological behaviour of stearate-based phase change nanofluids

  • Iglesias Prado, José Ignacio
  • Navarro, María Elena
  • Calviño Barreiro, Uxía
  • Ding, Yulong
  • Lugo Latas, Luis
A comprehensive study has been performed on the thermal and rheological behaviour of two sets of isooctyl stearate (PureTemp 8, PT8) based nanofluids with different concentrations of spherical MgO nanoparticles (up to 15 wt%) and graphene nanoplatelets (up to 2 wt%). The results show that the presence of the nanomaterials does not significantly alter the phase change temperatures of the base fluids, although the latent heat decreases by 27% and 7.6% for 15 wt% MgO and 1.0 wt% GnP-based nanofluids, respectively. Both nanomaterials are found to increase the thermal diffusivity of the nanofluids. GnP-based suspensions have a higher thermal diffusivity than the MgO ones at similar nanomaterial concentrations. Rheological analyses show that MgO-PT8 nanofluids behave as a viscoplastic material (solid at zero shear rate); whereas the GnP-PT8 samples are viscoelastic (liquid at zero shear rate). MgO nanoparticles promote the formation of large fractal agglomerates, leading to a strong gel network of particles within PT8, while platelet-shaped GnP gives a fluid-like behaviour., Agencia Estatal de Investigación | Ref. ENE2017-86425-C2-1-R, Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, Agencia Estatal de Investigación | Ref. PRE2021-097589, Xunta de Galicia | Ref. ED431C 2020/06, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Hybrid or mono nanofluids for convective heat transfer applications. A critical review of experimental research

  • Pérez Vallejo, Javier
  • Iglesias Prado, José Ignacio
  • Lugo Latas, Luis
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, Research on nanofluids has increased markedly in the last two decades. Initial attention has focused on conventional or mono nanofluids, dispersions of one type of solid nano-sized particles in a base fluid. Despite various challenges such as dispersion stability or increased pumping power, nanofluids have become improved working fluids for various energy applications. Among them, convective heat transfer has been the main research topic since the very beginning. Hybrid nanofluids, dispersions of two or more different nanoadditives in mixture or composite form, have received attention more recently. Research on hybrid nanofluids aims to further enhance the individual benefits of each single dispersion through potential synergistic effects between nanomaterials. Multiple experimental studies have been conducted independently analysing the convective heat transfer performance of mono or hybrid nanofluids for single-phase and two-phase convective heat transfer applications. However, there are still no general conclusions about which nanofluids, mono or hybrid, present better prospects. This review summarizes the experimental studies that jointly analyse both hybrid and mono nanofluids for these applications and the results are classified according to the heat transfer device used. Based on this criterion, three large groups of devices were noticed for single-phase convective heat transfer (tubular heat exchangers, plate heat exchangers and minichannel heat exchangers/heat sinks), while one group was identified for two-phase convective heat transfer (heat pipes). The main outcomes of these studies are summarized and critically analysed to draw general conclusions from an application point of view., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Ministerio de Ciencia e Innovación | Ref. PDC2021-121225-C21, Xunta de Galicia | Ref. ED481A-2018/287
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Experimental methodology to determine thermal conductivity of nanofluids by using a commercial transient hot-wire device

  • Iglesias Prado, José Ignacio
  • Calviño Barreiro, Uxía
  • Lugo Latas, Luis
The lack of a standard experimental procedure to determine thermal conductivity of fluids is noticeable in heat transfer processes from practical and fundamental perspectives. Since a wide variety of techniques have been used, reported literature data have huge discrepancies. A common practice is using manufactured thermal conductivity meters for nanofluids, which can standardize the measurements but are also somewhat inaccurate. In this study, a new methodology to perform reliable measurements with a recent commercial transient hot-wire device is introduced. Accordingly, some extensively studied fluids in the literature (water, ethylene glycol, ethylene glycol:water mixture 50:50 vol%, propylene glycol, and n-tetradecane) covering the range 0.100 to 0.700 W m−1 K−1 were used to check the device in the temperature range 283.15 to 333.15 K. Deviations between the collected data and the theoretical model, and repeatabilities and deviations between reported and literature values, were analyzed. Systematic deviations in raw data were found, and a correction factor depending on the mean thermal conductivity was proposed to operate with nanofluids. Considering all tested effects, the expanded (k = 2) uncertainty of the device was set as 5%. This proposed methodology was also checked with n-hexadecane and magnesium-oxide-based n-tetradecane nanofluids., Ministerio de Ciencia e Innovación | Ref. PID2020-112846RB-C21, Ministerio de Ciencia e Innovación | Ref. PDC2021-121225-C21, Xunta de Galicia | Ref. ED481A-2018/287, Ministerio de Economía y Competitividad | Ref. ENE2017-86425-C2-1-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

A comprehensive study of the thermophysical and rheological properties of ZrO2 based nanofluids as geothermal fluids

  • Calviño Barreiro, Uxía
  • Iglesias Prado, José Ignacio
  • Vallejo, Javier P.
  • Sohel Murshed, S.M.
  • Lugo Latas, Luis
Geothermal heat pump systems in residential and commercial applications have become popular in many countries over the past years. The heat transfer performance of the ground heat exchangers in these systems has still room for improvement since they have huge influence on the overall efficiency. Likewise, new heat transfer fluids with enhanced properties, known as nanofluids, have been proposed as a potential solution to substitute the conventional working fluids and to improve the heat transfer processes and performance. A reliable and appropriated proposal of nanofluids for a particular application must include a complete fluid dynamic characterization including thermophysical, rheological, heat transfer coefficients, and pressure drops analysis, as well as physical or chemical characterization of the nanomaterial. In this study, a novel proposal of propylene glycol:water (10:90 vol%)-based zirconium oxide nanofluids of different nanoparticle mass concentrations (0.25, 0.50, 0.75, 1.0, and 5.0 wt%) as possible geothermal working fluids and their thermophysical and rheological characterization are performed. Thus, the nanopowder was extensively investigated by means of Transmission Electron Microscopy, High Resolution Transmission Electron Microscopy, X-Ray diffraction, and Ultraviolet visible spectroscopy obtaining the shape, size distribution, d-spacing, electron diffraction pattern, and crystallinity. Then, thermal conductivities, dynamic viscosities, densities, and isobaric heat capacities for base fluid and nanofluids were measured by transient hot wire, rotational rheometry, vibrating tube, and differential scanning calorimetry methods, respectively. Increases in thermal conductivity, dynamic viscosity, and density of the nanofluids up to 2.8%, 13%, and 4.1% were found, respectively, while decreases in heat capacity reached 11% in comparison to the base fluid. Different models and equations were also employed to analyse the experimental data., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, European Cooperation in Science and Technology | Ref. CIG15119, Fundação para a Ciência e a Tecnologia | Ref. UIDB/50022/2020, Agencia Estatal de Investigación | Ref. PRE2021-097589, Xunta de Galicia | Ref. ED481A-2021/284, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Convection behaviour of mono and hybrid nanofluids containing B4C and TiB2 nanoparticles

  • Pérez Vallejo, Javier
  • Ansia Fernández, Lucas
  • Calviño Barreiro, Uxía
  • Marcos Millán, Marco
  • Fernández Seara, José
  • Lugo Latas, Luis
Hybrid nanofluids are intended to improve heat transfer due to possible synergistic effects between nanoparticles. Detailed studies comparing convection within hybrid nanofluids and equivalent mono nanofluids are still required to understand these effects, especially under turbulent flow. Boron carbide and titanium diboride are ceramics with interesting thermal properties that have not been commonly used in nanofluid design. A propylene glycol/water mixture at 20/80 wt% protects against freezing down to −7 °C and is frequently used as working fluid in cooling applications. This experimental study evaluates the behaviour of the heat transfer coefficient, pressure drop and performance index of B4C and TiB2 mono nanofluids and TiB2/B4C hybrid nanofluid based on a propylene glycol/water mixture at 20/80 wt% through a double pipe heat exchanger. Three average temperatures in the range 25–45 °C and different flow rates in the range 300–700 L/h (turbulent regime) are studied. Dimensionless analyses are performed using Nusselt, Prandtl, and Reynolds numbers and Darcy friction factor. The TiB2/B4C hybrid nanofluid shows the highest heat transfer coefficient improvements, up to 13%, and the highest performance index ratio, up to 1.03. This could be explained by potential nanoparticle synergistic effects that are especially evidenced through the dynamic viscosity., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, Agencia Estatal de Investigación | Ref. PRE2021-097589
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Heat transfer and hydrodynamic performance of ZrO2 geothermal nanofluids through tubular and plate heat exchangers

  • Calviño Barreiro, Uxía
  • Montenegro Vázquez, Iván
  • Sohel Murshed, S.M.
  • Fernández Seara, José
  • Pérez Vallejo, Javier
  • Lugo Latas, Luis
The improvement in heat transfer equipment plays a significant role to enhance the overall performance of many systems and a wide variety of industrial processes. Heat exchangers are widely used in many of these applications and, with the aim of limiting the growing of energy demand, further improvement is needed. A low-enthalpy geothermal system is commonly constituted by a ground heat exchanger, a heat pump unit, and indoor heating/ cooling units. In the ground heat exchanger circuit, the heat exchange occurs between the fluid of the wellbore and the ground through a tubular section similar to that of the inner tube of a Double-Tube Heat Exchanger (DTHE), and between the fluid of the wellbore and the refrigerant of the heat pump in the evaporator/condenser, which is typically a Plate Heat Exchanger (PHE). The use of new nano-enhanced heat transfer fluids featuring improved properties, known as nanofluids, has been proposed as a potential solution for energy efficiency improvement. This study aims to analyse the feasibility of ZrO2 nanofluids based on a propylene glycol: water 10:90 vol% mixture as working fluids in heat transfer applications, focusing on renewable energy systems such as low-enthalpy geothermal installations. The heat transfer performance and hydrodynamic behaviour of four new ZrO2-based nanofluids at nanoparticle mass concentrations of 0.25, 0.50, 0.75, and 1.0 wt% are analysed and compared with the base fluid. Tests through a PHE and a DTHE were performed, and convective heat transfer coefficients and pressure drops were obtained in laminar and turbulent regimes. Increases of the convective heat transfer coefficients up to 123 % and 8.8 % were found for the nanofluids in comparison to the base fluid for laminar flow in the PHE and for turbulent flow in the DTHE, respectively. Finally, a dimensionless analysis was carried out through Nusselt and Reynolds numbers and Darcy friction factor., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, Agencia Estatal de Investigación | Ref. PRE2021-097589, Fundação para a Ciência e a Tecnologia, Centro Universitario de la Defensa en la Escuela Naval Militar, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

An experimental study of novel nanofluids based on deep eutectic solvents (DESs) by Choline chloride and ethylene glycol

  • Jafari, Kimia
  • Hossein Fatemi, Mohammad
  • Lugo Latas, Luis
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, In this work, the preparation and characterization of some new nanofluids based on deep eutectic solvents (DESs) consisting of a hydrogen bond acceptor, ethylene glycol (EG), and a hydrogen bond donor, choline chloride (ChCl), as well as water, are presented. The nanofluids were designed by the dispersion of spherical MgO nanoparticles in four different DESs, ChCl:EG (molar ratio of 1:2), 1ChCl:5EG, 1ChCl:2EG:2Water, and 1ChCl:5EG:2Water. The stability of nanofluids was carried out by measuring size distribution for five days, which discovered the best results obtained with nanofluids of dispersed MgO in DES 1ChCl:5EG. Thermophysical properties (thermal conductivity and density) were measured and the influence of nanoparticles’ mass fraction, temperature, and water content all were examined. The acquired outcomes revealed that the trend of density was reducing by increment in temperature since for pure base fluids and DES-based nanofluids 1.3% decrement were recorded, averagely (the decline in density was sharper in the case of DES 1ChCl:5EG and its based nanofluids). The thermal conductivity was almost constant during the range of 283.15–333.15 K. It confirmed that the thermal conductivities of prepared nanofluids based on DESs with water were higher in comparison to the ones based on DESs without water and nanoparticles concentration could promote thermal conductivity. The greatest enhancement was gained at 10 wt% of MgO suspended in DES 1ChCl:2EG. The isobaric thermal expansivity was also determined at different temperatures. Eventually, the general conclusions were drawn and concerning the results, the MgO/DES 1ChCl:2EG 10 wt% nanofluids was introduced as the most efficient., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, Agencia Estatal de Investigación | Ref. ENE2017-86425-C2-1-R
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Thermophysical, rheological and electrical properties of mono and hybrid TiB2/B4C nanofluids based on a propylene glycol: water mixture

  • Pérez Vallejo, Javier
  • Żyła, Gaweł
  • Ansia, Lucas
  • Fal, Jacek
  • Traciak, Julian
  • Lugo Latas, Luis
Financiado para publicación en acceso aberto: Universidade de Vigo/CISUG, Hybrid nanofluids aim to further improve the characteristics of mono nanofluids. However, experimental studies that jointly explore the physical properties of hybrids and the corresponding mono nanofluids are missing. In this work, mono B4C and TiB2 and hybrid TiB2:B4C nanoadditives are used for the first time to design nanofluids based on propylene glycol:water 20:80 wt%. The density, isobaric heat capacity, and thermal conductivity of the nanofluids are determined by the oscillating U-tube, differential scanning calorimetry, and transient hot wire methods, respectively. The rheological behaviour is investigated through rotational rheometry. Additionally, surface tension and electrical conductivity are investigated. The B4C mono nanofluid shows the highest improvements of thermal conductivity (6.0%) and electrical conductivity (70 times higher), but also the highest viscosity increases (51–54%). The hybrid nanofluid presents intermediate values between those of the mono nanofluids for all the properties except dynamic viscosity. Interactions between spherical and sheet-like nanoparticles explain this behaviour., Agencia Estatal de Investigación | Ref. ENE2017-86425-C2-1-R, Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Advanced backfilling materials for enhancing the thermal efficiency of ground heat exchangers

  • Calviño Barreiro, Uxía
  • Pérez Vallejo, Javier
  • Ding, Yulong
  • Lugo Latas, Luis
Residential and industrial heating and cooling systems are among the largest consumers of energy. To meet the growing energy demand in this sector, sustainable solutions are being increasingly adopted, with geothermal heat pump systems emerging as a popular choice. The main component of these systems is the ground heat exchanger that comprises a borehole, typically filled with grout, and tubing that carries a heat transfer fluid, transferring thermal energy between the ground and the heat pump. To enhance the thermal performance of the backfilling material, the addition of phase change materials has been presented as a promising solution. This study examines the addition of a microencapsulated organic phase change material slurry into three commonly used geothermal boreholes backfilling materials (water, sand, and bentonite) at various concentrations. The phase change characteristics, including heating–cooling curves from 2 to 10 K⋅min− 1 , were analysed by differential scanning calorimetry. Isobaric heat capacities within solid and liquid phases were also measured. Solidliquid transition temperatures vary up to 4.8 K for melting and 5.1 K for crystallization of bentonite-based samples. Up to 7 times higher latent heat and up to 3.5 times higher isobaric heat capacity were noticed with increasing loading of microencapsulated phase change material. The designed materials show potential characteristics as backfilling materials for geothermal vertical boreholes, particularly those using bentonite and sand backfills., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, Agencia Estatal de Investigación | Ref. PRE2021-097589
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Development and thermophysical profile of cetyl alcohol-in-water nanoemulsions for thermal management

  • Cabaleiro Álvarez, David
  • Losada Barreiro, Sonia
  • Agresti, Filippo
  • Hermida Merino, Carolina
  • Fedele, Laura
  • Lugo Latas, Luis
  • Barison, Simona
  • Martínez Piñeiro, Manuel
This study focuses on the preparation, thermophysical and rheological characterization of phase change material nanoemulsions as latent functionally thermal fluids. Aqueous dispersions with fine droplets of cetyl alcohol (with a melting temperature at ~321 K) were prepared by means of a solvent-assisted method, combining ultrasonication with non-ionic and anionic emulsifiers. Eicosyl alcohol (melting at ~337 K) and hydrophobic silica nanoparticles were tested as nucleating agents. Droplet size studies through time and after freeze–thaw cycles confirmed the good stability of formulated nanoemulsions. Phase change analyses proved the effectiveness of eicosyl alcohol to reduce subcooling to a few Kelvin. Although phase change material emulsions exhibited thermal conductivities much larger than bulk cetyl alcohol (at least 60% higher when droplets are solid), reductions in this property reached 15% when compared to water. Samples mainly showed desirable Newtonian behavior (or slight shear thinning viscosities) and modifications in density around melting transition were lower than 1.2%. In the case of phase change material nanoemulsions with 8 wt.% content of dispersed phase, enhancements in the energy storage capacity overcome 20% (considering an operational temperature interval of 10 K around solid–liquid phase change). Formulated dispersions also showed good thermal reliability throughout 200 solidification–melting cycles., European Commission | Ref. SOE2 / P1 / P0823, Ministerio de Ciencia e Innovación | Ref. ENE2017-86425-C2-1-R, Ministerio de Ciencia e Innovación | Ref. PID2020-112846RB-C21
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Thermophysical, rheological and dielectric behaviour of stable carbon black dispersions in PEG200

  • Marcos Millán, Marco
  • Fal, Jacek
  • Pérez Vallejo, Javier
  • Żyła, Gaweł
  • Lugo Latas, Luis
Phase change materials can store or release large amounts of energy during phase change. An increasing number of authors are studying the influence of the dispersion of nanometric particles on these materials. This article presents the design and experimental characterization of temporal stability, thermal conductivity, isobaric heat capacity, phase change transitions, rheological behaviour, and dielectric properties of nano-enhanced phase change materials based on carbon black (CB) dispersions in polyethylene glycol (PEG200) by using polyvinylpyrrolidone (PVP) as surfactant. We studied the temporal stability of carbon black nanoparticles dispersed in PEG200 using dynamic light scattering and spectrophotometry techniques. All the samples showed good temporal stability, since the measurements of the hydrodynamic size of the nanoparticles are practically constant over time and the wavelength observed by UV–vis shows a small variation of around 4% for static conditions. We observed small changes in thermal conductivity and isobaric heat capacity. Nevertheless, the thermograms evidence how the latent heat clearly increases with the load of carbon black nanoparticles up to four times that of the PEG200. The viscosity studies do not show variation with shear rate, indicating a Newtonian behaviour, excluding the 2.0 wt% CB/PVP + PEG200 nanofluid. Additionally, we noticed frequency dependent and independent regions for permittivity, Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, Ministerio de Universidades | Ref. 33.50.460A.752, European Cooperation in Science and Technology | Ref. IG15119, Universidade de Vigo/CISUG
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Assessing anatase TiO2 nanofluids performance: experimental heat transfer coefficients vs. Mouromtseff number ratios

  • Calviño Barreiro, Uxía
  • Prado, Jose I.
  • Pérez Vallejo, Javier
  • Lugo Latas, Luis
This research aims to evaluate the efficacy of Mouromtseff’s numbers in assessing the thermal transfer performance of titanium oxide (TiO2) nanosized dispersions in convective heat transfer through a pipe. New experimental coefficients of convective heat transfer, thermophysical and rheological characterisation are carried out for TiO2-based nanodispersions in an aqueous propylene glycol 30 vol% mixture at various nanoadditive mass loadings (from 0.25 to 2.0 wt%). Different Mouromtseff’s number formulations, including the Dittus–Boelter and Simons expressions, were obtained from experimental data of thermophysical properties, enabling concise analyses on the prospective improvement of heat transfer in cooling and heating systems. The morphology, particle size, and crystallinity of the anatase TiO2 nanopowder were confirmed, and the stability of the nanofluids with various surfactants was evaluated, with PSS at a 1:4 mass ratio being optimal. Slight increments in thermal conductivity (up to 1.5%) and density (up to 1.3%) with nanoparticle loading were observed, while isobaric heat capacity presents a decreasing trend (less than 13%). Dynamic viscosity increases with higher nanoadditive concentrations, 8.8% for the 2.0 wt% A-TiO2/PG:W 30:70 + PSS 1:4 nanofluid. The employed Dittus–Boelter and Simons expressions correctly predict a worsening of the convective heat transfer, but the percentages diverge slightly from experimental data., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, Agencia Estatal de Investigación | Ref. PRE2021-097589
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Influence of crystal structure on the thermophysical properties and figures-of-merit of propylene glycol: water-based SiC nanofluids

  • Pérez Vallejo, Javier
  • Febrero Garrido, Lara
  • Cacabelos Reyes, Antón
  • González Gil, Arturo
  • Lugo Latas, Luis
Silicon carbide is a material with a promising thermal conductivity. However, no literature has been found on SiC nanofluids based on propylene glycol:water mixtures (widely used in renewable installations). Likewise, the contribution of α-SiC and β-SiC to the thermophysical properties of nanofluids has scarcely been explored. In this work, dispersions of α-SiC and β-SiC on propylene glycol:water 30:70 wt% at 1 and 2% wt% concentration are designed. Densities, thermal conductivities, dynamic viscosities, and isobaric heat capacities from 293.15 to 313.15 K are obtained by vibrating tube densimetry, transient-hot-wire technique, rotational rheometry and differential scanning calorimetry, respectively. Convective heat transfer performance is also assessed using figures-of-merit. Thermal conductivity and viscosity show a greater dependence on the crystal structure. The β-SiC nanofluids present the highest increases of thermal conductivity (12%) and dynamic viscosity (17%). The least complex crystal structure (β-SiC) exhibits better prospects for convection applications both for laminar and turbulent flow., Centro Universitario de la Defensa (Marín) | Ref. PICUD2022-07, Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Agencia Estatal de Investigación | Ref. PDC2021-121225-C21, European Union NextGenerationEU/PRTR
Investigo. Repositorio Institucional de la Universidade de Vigo
Publicación Artículo científico (JournalArticle)

Improving the sub-cooling and thermophysical profile of isopropyl palmitate for refrigeration applications

  • Marcos Millán, Marco
  • Troncoso, Noelia G.
  • Iglesias Prado, José Ignacio
  • Pérez Vallejo, Javier
  • Murshed, S.M. Sohel
  • Lugo Latas, Luis
Phase change materials have been suggested for use in refrigeration systems or thermal energy storage. However, their low thermal conductivity as well as high sub-cooling hinder the use of these materials in such applications. This study presents the experimental design and characterization on phase change transitions, isobaric heat capacity, density, thermal conductivity, thermal diffusivity, and rheological behaviour of phase change materials based on isopropyl palmitate (IPP) that have been improved with the addition of nanoparticles. Four dispersions of graphene nanoplatelets (GnP2) in IPP were prepared, ranging from 0.25 to 2 wt% and stabilized with cetyltrimethylammonium bromide (CTAB) at a surfactant:nanoparticles mass ratio of 1:1. Similar hydrodynamic sizes of the dispersed nanoadditives for three weeks were confirmed, showing good temporary colloidal stability. A 10% reduction in sub-cooling was observed for the 1 wt% (CTAB:GnP2 1:1)/IPP sample and isobaric heat capacity decreased by up to 10% in the 2 wt% (CTAB:GnP2 1:1)/IPP sample. Enhancements in thermal conductivity of up to 4.4% were evidenced for the 2 wt% (CTAB:GnP2 1:1)/IPP nano-enhanced phase change material. Moreover, increasing temperature caused an exponential drop in shear viscosity, with maximum diminution of 61% for the base IPP. Similar behaviour was observed for (CTAB:GnP2 1:1)/IPP nanofluids at all studied concentrations. The decrease in sub-cooling and improved thermophysical properties reinforce nano-enhanced isopropyl palmitate’s suitability for refrigeration and cold storage., Agencia Estatal de Investigación | Ref. PID2020-112846RB-C21, Xunta de Galicia | Ref. GRC-ED431C 2020/06, Universidade de Vigo/CISUG, Fundação para a Ciência e a Tecnologia | Ref. UIDB/50022/2020