Pasar al contenido principal

METODOLOGIA DE DISEÑO DE INTERFACES CRYO-CMOS PARA APLICACIONES DE COMPUTACION CUANTICA

PID2020-114110RA-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2020
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 17
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cryogenic measurement of CMOS devices for quantum technologies

  • Pérez-Bailón, Jorge
  • Tarancón, Miguel
  • Celma, Santiago
  • Sánchez-Azqueta, Carlos
In this article we present the experimental characterization of active components of a standard 65 nm CMOS technology for a temperature range from 313 to 5 K, analyzing the variation of the main parameters over temperature and voltage, recovering their main parameters (threshold voltage Vth , transconductance Gm and channel conductance GDS ). The measurement has been carried out wire-bonding the bare dies with the devices to a dedicated printed circuit board (PCB) that has been placed inside a dilution refrigerator. The ID - VDS curves for both NMOS and PMOS transistors shows an increase of ID in the cryogenic regime that is more relevant for high values of VGS because for lower values it is partially compensated by the variation of Vth . Also, a kink is observed in these curves for high VDS values, caused by the bulk current generated by impact ionization at the drain combined with the increased resistivity of the frozen-out substrate. The transconductance Gm reaches non-zero values for higher VGS as T decreases and then peaks to higher values in the cryogenic regime. In turn, GDS increases for increasing T , following the behavior observed for ID . Both results are in accordance with other thermal characterizations carried out on CMOS transistors in different technologies., 10.13039/501100004837-Spanish Ministry of Science and Innovation (Grant Number: PID2020-114110RA-I00). Consejo Superior de Actividades Científicas (CSIC) Program for the Spanish Recovery, Transformation and Resilience Plan Recovery and Resilience Facility of the European Union, established by the Regulation (EU) 2020/2094 (Grant Number: 20219PT007)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Characterization of 65-nm CMOS integrated resistors in the cryogenic regime

  • Marqués-García, Jorge
  • Pérez-Bailón, Jorge
  • Celma, Santiago
  • Sánchez-Azqueta, Carlos
This article presents the experimental characterization and modeling of CMOS resistors in a temperature range extending from room temperature (300 K) down to the deep cryogenic regime at 4 K. A set of poly-silicon resistors with different bulk structures and sizing have been fabricated in a 65 nm CMOS process and their I–V curves have been obtained experimentally in the 4 to 300 K range with a temperature step of only 0.5 K to obtain a large set of resistance values equally distributed along the temperature range. The plot of the resistance values against temperature has allowed us to obtain the temperature coefficient α(T) of the different resistors in the whole temperature range down to 4 K. Interestingly, for all the measured resistors the α(T) –T curves show a change in tendency for temperatures spanning from 66 to 98 K, this is, in the vicinity of the condensation temperature of nitrogen (77 K), where most of the thermal contraction of materials occurs., 10.13039/501100011033-Spanish Agencia Estatal de Investigación (AEI) (Grant Number: PID2020-114110RA-I00). CSIC Spanish Recovery, Transformation and Resilience Plan Recovery and Resilience Facility of the European Union, established by the Regulation (EU) 2020/2094 (Grant Number: 20219PT007)., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Design-window methodology for inductorless noise-cancelling CMOS LNAs

  • Martinez-Perez, A. D.
  • Aznar, F.
  • Flandre, D.
  • Celma, S.
This paper presents an optimization methodology for inductorless noise-cancelling CMOS Low-Noise Amplifiers (LNA), whose performance typically depends on a tight balance in the design of two transistor stages. Due to the different functions of the two parts, noise-cancelling amplifiers become very difficult to analyze in detail by closed-form expressions or straight simulations: each section significantly affects the results of the other. In addition, opposed specifications, such as gain and cut-off frequency, suppose another grade of complexity due to the interplay of the two branches of the circuit. As a solution, the proposed methodology uses a visualization of the design window in 2-dimensional space to optimize the different parameters of the specifications without compromising the others. All specification constraints are represented in a single figure instead of one graph per parameter. Compared with most optimization methods, the design window methodology observes the design span instead of isolated design points that might not guarantee feasibility. Furthermore, as a simulation-driven exploration method, it benefits from complete device models with high-order effects that would be too complex to include in analytical expressions but critical to achieving maximum efficiency. As an example of the method, the paper describes the optimization of the well-known CS-CG noise-cancelling LNA in 65-nm standard CMOS technology. Final post-layout simulations report very competitive results with a 3.7-dB noise figure, a 17-dB gain, and a cut-off frequency above 7 GHz.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Suitability of Generalized GAROs on FPGAs as PUFs or TRNGs considering spatial correlations

  • Garcia-Bosque, Miguel
  • Naya, Abel
  • Díez-Señorans, Guillermo
  • Sánchez-Azqueta, Carlos
  • Celma, Santiago
In the last years, guaranteeing the security in Internet of things communications has become an essential task. In this article, the bias of a wide set of oscillators has been studied to determine their suitability as both true random number generators (TRNGs) and physically unclonable functions (PUFs). For this purpose, a generic configurable structure has been proposed and implemented in an field programmable gate array (FPGA). With this implementation, by introducing some external signals it is possible to configure the system in different oscillator topologies. This way, we have managed to analyze 2730 oscillators composed by seven lookup tables (LUTs) without having to resynthesize the code each time. The performed analysis has included conventional ring oscillators, Galois ring oscillators, and newly proposed oscillator topologies. From this analysis, we have concluded that none of these oscillators behave as an ideal TRNG but ring oscillators present the closest to an ideal behavior. Regarding their suitability as PUFs, some of the newly proposed oscillators in this article present a high reproducibility, higher than that of conventional ring oscillator PUF (RO-PUF) and a high uniqueness. Furthermore, we have noticed that both their reproducibility and their uniqueness tend to improve when increasing the length of the oscillators, which opens the possibility of finding new oscillators with even better properties by studying oscillators of bigger lengths. Finally, by studying the spatial correlation of the bias of these oscillators, we have observed that they present a much lower spatial correlation compared to the ring oscillators, which opens the possibility of using these oscillators in PUF architectures that use more comparisons than typical RO-PUFs.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Oscillator Selection Strategies to Optimize a Physically Unclonable Function for IoT Systems Security

  • Aparicio-Téllez, Raúl
  • Garcia-Bosque, Miguel
  • Díez-Señorans, Guillermo
  • Celma, Santiago
Physically unclonable functions avoid storing secret information in non-volatile memories and only generate a key when it is necessary for an application, rising as a promising solution for the authentication of resource-constrained IoT devices. However, the need to minimize the predictability of physically unclonable functions is evident. The main purpose of this work is to determine the optimal way to construct a physically unclonable function. To do this, a ring oscillator physically unclonable function based on comparing oscillators in pairs has been implemented in an FPGA. This analysis shows that the frequencies of the oscillators greatly vary depending on their position in the FPGA, especially between oscillators implemented in different types of slices. Furthermore, the influence of the chosen locations of the ring oscillators on the quality of the physically unclonable function has been analyzed and we propose five strategies to select the locations of the oscillators. Among the strategies proposed, two of them stand out for their high uniqueness, reproducibility, and identifiability, so they can be used for authentication purposes. Finally, we have analyzed the reproducibility for the best strategy facing voltage and temperature variations, showing that it remains stable in the studied range.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A 19.5 Ghz 5-bit digitally programmable phase shifter for active antenna arrays

  • Esteban Eraso, Uxua
  • Sánchez-Azqueta, Carlos
  • Aldea, Concepción
  • Celma, Santiago
This paper presents the design of a new phase shifter to be used in a receiver of active antenna array operating in the range from 17 GHz to 22 GHz. Beamforming is achieved by controlling the phase of the signal in each radiant element. In this context, the phase shift is obtained by the combination of a quadrature signal generator (QSG) and a variable gain amplifier (VGA). This work is focused on the design of a VGA which has a set of dummy transistors to keep the input and output impedance constant. The phase shifter is digitally programmable using a 5-bit word. The system was laid out using a 65 nm CMOS process, and the physical post-layout results show that the phase shifter achieves root mean square errors of 4.5° for the phase and 0.79 dB for the gain at a frequency of 19.5 GHz. A comparative analysis with other recently published phase shifters shows that the proposed phase shifter presents a good compromise between power consumption and accuracy.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

CMOS linear laser driver for intermediate frequency over fiber (IFoF) links

  • Paredes-Páliz, Diego F.
  • Martinez-Perez, Antonio D.
  • Aznar, Francisco
  • Celma, Santiago
The main objective of the proposed linear laser driver (LLD) is to reduce signal distortion in an analog direct modulation laser configuration used for intermediate frequency over fiber links. This work draws on an open-loop configuration featuring two differential pair blocks in a cascade arrangement to achieve a bandwidth measurement of 415 MHz at the half-power point, a total harmonic distortion of 4.57% for a fundamental frequency of 100 MHz, and an amplitude of 100 mVpp. The LLD provides a gain of 12.3 dB for a differential output and an output impedance of 46 Ω. The design, layout, and integration correspond to the process design kit for TSMC 65-nm CMOS technology. Experimental results show the advantage over other previously reported laser drivers.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Cryogenic measurement of CMOS devices for quantum technologies

  • Pérez-Bailón, Jorge
  • Tarancón, Miguel
  • Celma, Santiago
  • Sánchez-Azqueta, Carlos
In this article we present the experimental characterization of active components of a standard 65 nm CMOS technology for a temperature range from 313 to 5 K, analyzing the variation of the main parameters over temperature and voltage, recovering their main parameters (threshold voltage Vth , transconductance Gm and channel conductance GDS ). The measurement has been carried out wire-bonding the bare dies with the devices to a dedicated printed circuit board (PCB) that has been placed inside a dilution refrigerator. The ID - VDS curves for both NMOS and PMOS transistors shows an increase of ID in the cryogenic regime that is more relevant for high values of VGS because for lower values it is partially compensated by the variation of Vth . Also, a kink is observed in these curves for high VDS values, caused by the bulk current generated by impact ionization at the drain combined with the increased resistivity of the frozen-out substrate. The transconductance Gm reaches non-zero values for higher VGS as T decreases and then peaks to higher values in the cryogenic regime. In turn, GDS increases for increasing T , following the behavior observed for ID . Both results are in accordance with other thermal characterizations carried out on CMOS transistors in different technologies.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Otros (Other)

A fully integrated nanosecond burst RF generator for quantum technologies

  • Sánchez-Azqueta, Carlos
  • Aldea, Concepción
  • Celma, Santiago
Quantum technologies is an emerging field of physics and engineering based on exploiting properties of quantum mechanics such as entanglement, superposition, or tunneling, and which is expected to impact many applications, such as communications, simulation, computation, or sensing and metrology. The operation of quantum technologies is based on the manipulation of the quantum states of certain devices, either to induce transitions between states or to detect the transitions. Irrespective of the practical realization of these quantum devices, their manipulation requires interacting with their quantum resonant states, for which very narrow radio‐frequency (RF) bursts in the range of the GHz are required. Arbitrary waveform generators are used to generate these signals for test purposes, but this is not suitable for practical quantum technology applications, which will need to produce the required bursts by specific circuit building blocks with low power and small dimensions. Here, an integrated RF burst generator capable of producing GHz bursts shorter than 1 ns is presented. The proposed architecture is tested using a 5 GHz quadrature LC‐tank voltage‐controlled oscillator (LC‐VCO), showing that the four equally spaced phases can be switched every 500 ps, which allows the generation of more complex RF bursts for optimized quantum state manipulation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Characterization of 65-nm CMOS Integrated Resistors in the Cryogenic Regime

  • Marqués-García, Jorge
  • Pérez-Bailón, Jorge
  • Celma, Santiago
  • Sánchez-Azqueta, Carlos
This article presents the experimental characterization and modeling of CMOS resistors in a temperature range extending from room temperature (300 K) down to the deep cryogenic regime at 4 K. A set of poly-silicon resistors with different bulk structures and sizing have been fabricated in a 65 nm CMOS process and their I–V curves have been obtained experimentally in the 4 to 300 K range with a temperature step of only 0.5 K to obtain a large set of resistance values equally distributed along the temperature range. The plot of the resistance values against temperature has allowed us to obtain the temperature coefficient α(T )of the different resistors in the whole temperature range down to 4 K. Interestingly, for all the measured resistors the α(T )–T curves show a change in tendency for temperatures spanning from 66 to 98 K, this is, in the vicinity of the condensation temperature of nitrogen (77 K), where most of the thermal contraction of materials occurs
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

An analysis of the behaviour of a PUF based on ring oscillators depending on their locations

  • Garcia-Bosque, M.
  • Aparicio, R.
  • Diez-Senorans, G.
  • Sanchez-Azqueta, C.
  • Celma, S.
In this paper, an analysis regarding the influence of the chosen locations of the ring oscillators in the performance of a ring oscillator Physically Unclonable Function has been carried out. For this purpose, five different strategies to select a small set of locations out of a big set of locations to construct a PUF have been proposed and compared. The analysis reflects that, depending on the chosen selection strategy, the quality of the PUF can be greatly affected, especially in terms of uniqueness.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A Study of the Optimal Logic Combinations of RO-Based PUFs on FPGAs to Maximize Identifiability

  • Aparicio-Téllez, Raúl
  • Garcia-Bosque, Miguel
  • Díez-Señorans, Guillermo
  • Aznar, Francisco
  • Celma, Santiago
One of the challenges that wireless sensor networks (WSNs) need to address is achieving security and privacy while keeping low power consumption at sensor nodes. Physically unclonable functions (PUFs) offer a challenge–response functionality that leverages the inherent variations in the manufacturing process of a device, making them an optimal solution for sensor node authentication in WSNs. Thus, identifiability is the fundamental property of any PUF. Consequently, it is necessary to design structures that optimize the PUF in terms of identifiability. This work studies different architectures of oscillators to analyze which ones exhibit the best properties to construct a RO-based PUF. For this purpose, Generalized Galois Ring Oscillators (GenGAROs) are used. A GenGARO is a novel type of oscillator formed by a combination of up to two input logical operations connected in cascade, where one input is the output of the previous operation and the other is the feedback signal. GenGAROs include some previously proposed oscillators as well as many new oscillator designs. Thus, the architecture of GenGAROs is analyzed to implement a GenGARO-PUF on an Artix-FPGA. With this purpose, an exhaustive study of logical operation combinations that optimize PUF performance in terms of identifiability has been conducted. From this, it has been observed that certain logic gates in specific positions within the oscillator contribute to constructing a PUF with good properties, and by applying certain constraints, any oscillator generated with these constraints can be used to construct a PUF with an equal error rate on the order of or below 10−11 using 100-bit responses. As a result, a design methodology for FPGA-based RO-PUFs has been developed, enabling the generation of multiple PUF primitives with high identifiability that other designers could exploit to implement RO-based PUFs with good properties.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A New Metric Measuring Steering Accuracy of Digitally Controlled Phase Shifters

  • Aznar, Francisco
  • Esteban-Eraso, Uxua
  • Perez-Martinez, Antonio D.
  • Celma, Santiago
This paper proposes a new metric to compare digitally controlled phase shifters, denoted as Beam Steering Error (BSE). The definition of BSE is introduced by an example of a 2-bit phase shifter, and it is compared to the traditionally used RMS phase error. The advantages during simulation stage of using this new indicator are shown for a real case of a 4-bit phase shifter designed in a 65−nm CMOS process.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Digitization algorithms in ring oscillator physically unclonable functions as a main factor achieving hardware security

  • Díez Señorans G.
  • García Bosque M.
  • Sánchez Azqueta C.
  • Celma Pueyo, S.
Since the discovery of the physical random functions and their subsequent refinement into physical unclonable functions (PUF), a great effort has been made in developing and characterizing these objects attending to their physical properties as well as conceiving a myriad of different examples in the search for a better application-specificity and suitability. However, comparatively little time has been devoted to the analysis of entropy extraction algorithms beyond the recognition of some limitations due to the environment influencing the PUF behavior. In this article we focus on well known PUF candidates based on ring oscillator delay, which are ideal for FPGA prototyping due to their tolerance to asymmetries in routing. We have studied the impact that different digitization algorithms of the responses have over their security properties. Specifically, we have analyzed the response probability distributions that arise from some popular techniques of digitization called "compensated measuring" methods, highlighting their lack of uniformity and how this might translate into cryptanalytically exploitable vulnerabilities. Furthermore, we propose a new family of digitization schemes named k-modular that exhibit both uniformity in response distribution and high entropy density on both physical and response space.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Exploiting nonlinear oscillator dynamics for on-chip thermal sensing

  • Aparicio-Téllez, Raúl
  • Garcia-Bosque, Miguel
  • Diez-Señorans, Guillermo
  • Celma, Santiago
Real-time monitoring of temperature in FPGAs is crucial to ensure system reliability, as local temperature variations can affect their performance. For these purposes, virtual temperature sensors such as Ring Oscillator (RO)-based sensors are widely used. However, efficiently implementing them with a minimal number of Look-Up Tables (LUTs) remains a significant challenge. In this paper, we propose a novel temperature sensor architecture based on nonlinear oscillators, implemented on a 28 nm Artix-7 FPGA. The proposed approach minimizes the usage of FPGA resources while maintaining accurate thermal sensing. As a result, several nonlinear oscillators are analyzed, achieving better sensitivity (0.020%/°C) over a 25 % wider temperature range compared to other RO-based temperature sensors reported in the literature for the 28 nm technology node. These results highlight the potential of these oscillators as efficient, low-resource alternatives for real-time thermal monitoring in FPGA.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Orthonormal splitting of RMS phase error in digitally controlled phase shifters

  • Aznar, Francisco
  • Esteban-Eraso, Uxua
  • Martínez-Pérez, Antonio D.
  • Fernández, Roque
  • Celma, Santiago
Traditionally, the RMS phase error has been the standard metric for assessing the quality of phase shifters used in phased-array beamforming antennas. However, this metric fails to isolate the different effects on the radiation pattern. This work proposes three novel metrics to provide a more nuanced analysis of digitally controlled phase shifters. These metrics, denoted as Beam Steering Error, Null Quality Error, and Side-Lobe Level Error, target specific performance characteristics of the radiation pattern. They are defined for any bit resolution, enabling the decomposition of the RMS phase error into three distinct components, each providing valuable insights into the performance of linear phased arrays. The limitations of conventional RMS phase error analysis are demonstrated, and the advantages of these new metrics are validated through a case study involving a 5-bit architecture implemented in a 65-nm CMOS process, as well as other phase shifters reported in the literature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

PUF optimization for IoT device authentication

  • Aparicio-Téllez, Raúl
  • Garcia-Bosque, Miguel
  • Díez-Señorans, Guillermo
  • Aldea, Concepcion
  • Celma, Santiago
Two critical aspects in IoT are security and resource consumption. Physically Unclonable Functions (PUFs) are hardware security primitives that exploit the inherent manufacturing variations of integrated circuits to generate unique identifiers. Due to their uniqueness and resistance to cloning, they are widely used for IoT device authentication. In this work, a novel approach to enhance the identifiability of compensated measurement PUFs is introduced. This method involves applying specific weight masks to the parameters extracted from the PUF entropy source before conducting comparisons to determine the output bit. This technique has been tested on several types of PUFs constructed using public datasets. As a result, it has been observed that the Equal Error Rate (EER) can be greatly improved, up to two orders of magnitude. The main advantage of this technique is that it does not modify the architecture of the compensated measurement PUF (which is interesting for IoT devices, as it does not require extra resources), while it also has proven to be generalizable, i.e., the optimal mask parameters can be found using a small set of devices and, then, generalized to a different bigger set of devices. This way, this proposal contributes to the development of novel authentication schemes for IoT devices, addressing both security and resource efficiency, critical issues in IoT environments.