Pasar al contenido principal

DISEÑO DE NUEVAS ARQUITECTURAS CRYO-CMOS PARA COMPUTADORES CUANTICOS SUPERCONDUCTORES

PID2023-150244OB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2023
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 11
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of cryogenic thermal stress cycles on the performance of integrated resistors

  • Esquíroz-Olloqui, Yago
  • Pérez-Bailón, Jorge
  • Celma, Santiago
  • Sánchez-Azqueta, Carlos
Cryogenic operation of CMOS circuits is essential for scalable quantum computing and other high-performance applications. Although much research has focused on the behavior of devices at low temperatures, the long-term effects of repeated thermal stress cycles remain largely unexplored. This work investigates the impact of consecutive cooling–heating cycles between 4 and 280 K on the electrical characteristics of 65-nm CMOS polysilicon resistors with varying sizes and doping types. Using a fully automated cryogenic measurement setup, eight full thermal cycles were applied to three different resistor structures. Resistance versus temperature (R–T) characteristics were measured in the full temperature range for each cycle. The results reveal the appearance of hysteresis in the curves R–T after thermal cycling, with the most pronounced effects observed in larger devices. In particular, the maximum resistance variation remained below 2% of the nominal value, a trend that is maintained after repeating the thermal cycle eight times. These findings suggest that while 65-nm CMOS resistors are suitable for cryogenic electronic systems, care has to be taken when designing high-precision systems, depending on the value of resistors, such as comparators or data converters., This work was supported in part by the Agencia Estatal de Investigacion under Grant PID2023-150244OB-I00 and in part by the Gobierno de Aragon under Grant PROY_T33 24., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ultrathin tungsten films enabling enhanced electrical response to spin currents

  • Morales-Aragonés, José Ignacio
  • Groen, Ingen
  • Hueso, Luis E.
  • Casanova, Fèlix
  • Pardo, José A.
  • Sánchez-Azqueta, Carlos
  • Teresa, José María de
  • Sangiao, Soraya
The efficient detection of spin currents is crucial for the development of next-generation spintronic devices. Here, we demonstrate that ultrathin W layers, with thicknesses down to 2 nm— equivalent to only four atomic planes—allow for highly efficient spin-to-charge conversion. From spin pumping experiments in YIG/W bilayers, we analyzed the inverse spin Hall effect (SHE) voltage dependence on W thickness and extracted a spin Hall conductivity of σSH = −1.14(6)× 105 Ω−1 m−1, yielding effective spin Hall angles ranging from −0.27(4) to −0.88(4) over the investigated thickness range. Furthermore, assuming the Elliott–Yafet spin scattering mechanism dominates, we estimate a spin diffusion length λsd = 4.3(5)×10−15Ωm2/ρW, where the W resistivity ρW is strongly dependent on thickness. Structural characterization, together with roomtemperature electrical resistivity measurements and the high spin-to-charge conversion efficiency observed, confirms the stabilization of the β-phase in these ultrathin W layers. We demonstrate that the monotonic increase of the inverse SHE voltage with decreasing W thickness persists down to 2-nm-thick W layer, reflecting the extremely short spin diffusion length. This allows for efficient spin-current detection in W layers below 5 nm, effectively doubling the voltage output at half the thickness. In the thinnest sample, a continuous 2-nm-thick W layer, the generated voltage exceeds 0.5 mV—well within the operating range of conventional electronics. These findings demonstrate not only the feasibility of spin-current detection in ultrathin W, but also its compatibility with conventional electronics. They highlight the strong potential of integrating ultrathin W layers with high-quality YIG films for the development of energy-efficient spintronic devices and sensors., The authors acknowledge Grants PID2020-112914RB-I00, PID2021-122511OB-I00, PID2023-146451OB-I00, PID2023-150244OB-I00 and PID2024-155708OB-I00, funded by MICIU/AEI/10.13039/501100011033 and ERDF/EU and Grants E13_23R, PROY_E29_24 and PROY_T33_24 funded by Gobierno de Aragón., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A Study of the Optimal Logic Combinations of RO-Based PUFs on FPGAs to Maximize Identifiability

  • Aparicio-Téllez, Raúl
  • Garcia-Bosque, Miguel
  • Díez-Señorans, Guillermo
  • Aznar, Francisco
  • Celma, Santiago
One of the challenges that wireless sensor networks (WSNs) need to address is achieving security and privacy while keeping low power consumption at sensor nodes. Physically unclonable functions (PUFs) offer a challenge–response functionality that leverages the inherent variations in the manufacturing process of a device, making them an optimal solution for sensor node authentication in WSNs. Thus, identifiability is the fundamental property of any PUF. Consequently, it is necessary to design structures that optimize the PUF in terms of identifiability. This work studies different architectures of oscillators to analyze which ones exhibit the best properties to construct a RO-based PUF. For this purpose, Generalized Galois Ring Oscillators (GenGAROs) are used. A GenGARO is a novel type of oscillator formed by a combination of up to two input logical operations connected in cascade, where one input is the output of the previous operation and the other is the feedback signal. GenGAROs include some previously proposed oscillators as well as many new oscillator designs. Thus, the architecture of GenGAROs is analyzed to implement a GenGARO-PUF on an Artix-FPGA. With this purpose, an exhaustive study of logical operation combinations that optimize PUF performance in terms of identifiability has been conducted. From this, it has been observed that certain logic gates in specific positions within the oscillator contribute to constructing a PUF with good properties, and by applying certain constraints, any oscillator generated with these constraints can be used to construct a PUF with an equal error rate on the order of or below 10−11 using 100-bit responses. As a result, a design methodology for FPGA-based RO-PUFs has been developed, enabling the generation of multiple PUF primitives with high identifiability that other designers could exploit to implement RO-based PUFs with good properties.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Novel Machine Learning-Resistant RO-Based PUF Optimized for IoT Device Authentication

  • Aparicio-Téllez, Raúl
  • Garcia-Bosque, Miguel
  • Díez-Señorans, Guillermo
  • Celma, Santiago
In this work, a novel Physically Unclonable Function (PUF) based on Generalized Galois Ring Oscillators (GenGAROs) optimized for IoT device identification purposes has been proposed and analyzed. A GenGARO is composed of a certain number of logic gates with up to two inputs connected in cascade so that one input corresponds to the output of the previous gate and the other to the output of the last one. The bias of the signal of these oscillators has been used to construct a GenGARO-PUF. Firstly, the combination of logic gates which optimize the response of the GenGARO-PUF in terms of identifiability has been studied. Once the optimal configuration of GenGARO has been found, a GenGARO-PUF of 11 Look-Up Tables (LUTs) has been implemented on FPGA and its properties have been analyzed and compared to a conventional RO-PUF implemented in the exact same locations of the FPGA and using the same hard constraints. The proposal of this work shows an average Inter- Hamming Distance (HD) of 49.9 % and an Equal Error Rate EER=1.52⋅10-12 using 100-bit responses. The GenGARO-PUF has proven to outperform the conventional Ring Oscillator (RO) PUF in terms of spatial autocorrelation, uniqueness, uniformity, bit-aliasing, identifiability and resistance to modeling attacks. Furthermore, a 3-LUT GenGARO-PUF has been proposed maintaining the prediction accuracy of the 11-LUT GenGARO-PUF, and showing that a good identifiability can still be achieved using fewer resources of the FPGA.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Improving Physically Unclonable Functions’ Performance Using Second-Order Compensated Measurement

  • Fernández-Aragón, Jorge
  • Diez-Señorans, Guillermo
  • Garcia-Bosque, Miguel
  • Aparicio-Téllez, Raúl
  • López-Pinar, Gabriel
  • Celma, Santiago
In this paper, we study the performance of second-order compensated measurement to generate a multi-bit response in physically unclonable functions (PUFs). The proposed technique is based on a novel second-order compensated measurement generating multiple bits instead of a single bit provided by the conventional compensated measurement. A PUF based on this technique has been proposed and implemented in 40 Artix-7 FPGAs, and its uniqueness and reproducibility have been compared to those of another PUF using the compensated measurement technique. In addition, we demonstrate that the best trade-off between identifiability and computation time performance is obtained when using only two bits. At the same time, the good performance of the technique has been demonstrated, improving the identifiability of a ring oscillator PUF (RO-PUF) between 70 and 90% compared to a RO-PUF that uses conventional compensated measurement. In particular, equal error rates (EER) of the order of EER∼10−16 can be achieved by combining the sign bit with another bit extracted using the proposed technique; and up to EER∼10−19 by using one more extra bit. In addition, the high reliability of the responses generated by this technique against possible temperature and voltage variations has been proved. These results show how this new technique improves the performance of the PUF in terms of identifiability, so it can be effectively used for device identification purposes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Exploiting nonlinear oscillator dynamics for on-chip thermal sensing

  • Aparicio-Téllez, Raúl
  • Garcia-Bosque, Miguel
  • Diez-Señorans, Guillermo
  • Celma, Santiago
Real-time monitoring of temperature in FPGAs is crucial to ensure system reliability, as local temperature variations can affect their performance. For these purposes, virtual temperature sensors such as Ring Oscillator (RO)-based sensors are widely used. However, efficiently implementing them with a minimal number of Look-Up Tables (LUTs) remains a significant challenge. In this paper, we propose a novel temperature sensor architecture based on nonlinear oscillators, implemented on a 28 nm Artix-7 FPGA. The proposed approach minimizes the usage of FPGA resources while maintaining accurate thermal sensing. As a result, several nonlinear oscillators are analyzed, achieving better sensitivity (0.020%/°C) over a 25 % wider temperature range compared to other RO-based temperature sensors reported in the literature for the 28 nm technology node. These results highlight the potential of these oscillators as efficient, low-resource alternatives for real-time thermal monitoring in FPGA.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Orthonormal splitting of RMS phase error in digitally controlled phase shifters

  • Aznar, Francisco
  • Esteban-Eraso, Uxua
  • Martínez-Pérez, Antonio D.
  • Fernández, Roque
  • Celma, Santiago
Traditionally, the RMS phase error has been the standard metric for assessing the quality of phase shifters used in phased-array beamforming antennas. However, this metric fails to isolate the different effects on the radiation pattern. This work proposes three novel metrics to provide a more nuanced analysis of digitally controlled phase shifters. These metrics, denoted as Beam Steering Error, Null Quality Error, and Side-Lobe Level Error, target specific performance characteristics of the radiation pattern. They are defined for any bit resolution, enabling the decomposition of the RMS phase error into three distinct components, each providing valuable insights into the performance of linear phased arrays. The limitations of conventional RMS phase error analysis are demonstrated, and the advantages of these new metrics are validated through a case study involving a 5-bit architecture implemented in a 65-nm CMOS process, as well as other phase shifters reported in the literature.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Ultrathin tungsten films enabling enhanced electrical response to spin currents

  • Morales-Aragonés, José Ignacio
  • Groen, Inge
  • Hueso, Luis E
  • Casanova, Fèlix
  • Pardo, José Ángel
  • Sánchez-Azqueta, Carlos
  • De Teresa, José María
  • Sangiao, Soraya
The efficient detection of spin currents is crucial for the development of next-generation spintronic devices. Here, we demonstrate that ultrathin W layers, with thicknesses down to 2 nm—equivalent to only four atomic planes—allow for highly efficient spin-to-charge conversion. From spin pumping experiments in YIG/W bilayers, we analyzed the inverse spin Hall effect (SHE) voltage dependence on W thickness and extracted a spin Hall conductivity of σSH = −1.14(6) × 105 Ω −1 m−1, yielding effective spin Hall angles ranging from −0.27(4) to −0.88(4) over the investigated thickness range. Furthermore, assuming the Elliott–Yafet spin scattering mechanism dominates, we estimate a spin diffusion length λsd = 4.3(5) × 10−15Ωm2/ρW, where the W resistivity ρW is strongly dependent on thickness. Structural characterization, together with roomtemperature electrical resistivity measurements and the high spin-to-charge conversion efficiency observed, confirms the stabilization of the β-phase in these ultrathin W layers. We demonstrate that the monotonic increase of the inverse SHE voltage with decreasing W thickness persists down to 2-nm-thick W layer, reflecting the extremely short spin diffusion length. This allows for efficient spin-current detection in W layers below 5 nm, effectively doubling the voltage output at half the thickness. In the thinnest sample, a continuous 2-nm-thick W layer, the generated voltage exceeds 0.5 mV—well within the operating range of conventional electronics. These findings demonstrate not only the feasibility of spin-current detection in ultrathin W, but also its compatibility with conventional electronics. They highlight the strong potential of integrating ultrathin W layers with high-quality YIG films for the development of energy-efficient spintronic devices and sensors.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

PUF optimization for IoT device authentication

  • Aparicio-Téllez, Raúl
  • Garcia-Bosque, Miguel
  • Díez-Señorans, Guillermo
  • Aldea, Concepcion
  • Celma, Santiago
Two critical aspects in IoT are security and resource consumption. Physically Unclonable Functions (PUFs) are hardware security primitives that exploit the inherent manufacturing variations of integrated circuits to generate unique identifiers. Due to their uniqueness and resistance to cloning, they are widely used for IoT device authentication. In this work, a novel approach to enhance the identifiability of compensated measurement PUFs is introduced. This method involves applying specific weight masks to the parameters extracted from the PUF entropy source before conducting comparisons to determine the output bit. This technique has been tested on several types of PUFs constructed using public datasets. As a result, it has been observed that the Equal Error Rate (EER) can be greatly improved, up to two orders of magnitude. The main advantage of this technique is that it does not modify the architecture of the compensated measurement PUF (which is interesting for IoT devices, as it does not require extra resources), while it also has proven to be generalizable, i.e., the optimal mask parameters can be found using a small set of devices and, then, generalized to a different bigger set of devices. This way, this proposal contributes to the development of novel authentication schemes for IoT devices, addressing both security and resource efficiency, critical issues in IoT environments.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Design of a 17–22 GHz 5-bit CMOS vector-sum phase shifter for SATCOM receivers

  • Esteban Eraso, Uxua
  • Sánchez-Azqueta, Carlos
  • Aznar, Francisco
  • Aldea, Concepción
  • Celma, Santiago
This paper presents a CMOS vector-sum phase shifter for SATCOM-on-the-move receiver front-ends in hybrid phased-array antennas. The proposed circuit is an active, digitally programmable 5-bit phase shifter composed of two variable-gain amplifiers (VGAs) followed by an active power combiner. A key feature of the proposal is the use of dummy transistor arrays to keep the input and output impedances constant across the different gain states, which helps preserve phase and gain accuracy. Implemented in 65-nm CMOS technology, the phase shifter achieves RMS phase and gain errors below 3° and 0.4 dB, respectively, over the 17–22 GHz frequency range. In comparison with previously reported active phase shifters operating in similar frequency ranges, the proposed design exhibits a competitive trade-off among phase accuracy, gain variation, bandwidth, and power consumption.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A Code‐Invariant QSG–VGA Co‐Design Methodology for Compact CMOS Vector‐Sum Phase Shifters

  • Esteban Eraso, Uxua
  • Sánchez-Azqueta, Carlos
  • Aznar, Francisco
  • Aldea, Concepción
  • Celma, Santiago
A circuit‐level co‐design methodology for compact vector‐sum phase shifters is presented and applied to a code‐invariant common‐gate variable‐gain amplifier (VGA) combined with a resistorless quadrature signal generator (QSG). The VGA uses unary active, polarity‐selection and dummy branches, so that the quadrature generator and the output summing node see an almost constant number of conducting devices for all phase states. This property enables a resistorless RLC quadrature signal generator in which the VGA input resistance replaces the explicit resistors of a conventional all‐pass I/Q network. A proof‐of‐concept circuit has been designed in a 65 nm CMOS technology to operate over the 17–22 GHz frequency range. The circuit provides 32 phase states with a nominal resolution of 11.25°. Post‐layout/EM simulations of the complete phase shifter show RMS phase and gain errors below 4.1° and 0.42 dB, respectively, with power consumption below 16 mW.