Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 29
Encontrada(s) 1 página(s)

Docta Complutense
Publicación Artículo científico (JournalArticle)

Polypropylene Nanocomposites Attained by In Situ Polymerization Using SBA-15 Particles as Support for Metallocene Catalysts: Effect of Molecular Weight and Tacticity on Crystalline Details, Phase Transitions and Rheological Behavior

  • Barranco García, Rosa
  • García Peñas, Alberto
  • Blázquez Blázquez, Enrique
  • Ressia, Jorge Aníbal
  • Quinzani, Lidia María
  • Vallés, Enrique Marcelo
  • Gómez-Elvira González, José Manuel
  • Pérez Tabernero, Ernesto
  • Cerrada García, María Luisa
In this study, nanocomposites based on polypropylene are synthesized by the in situ polymerization of propene in the presence of mesoporous SBA-15 silica, which acts as a carrier of the catalytic system (zirconocene as catalyst and methylaluminoxane as cocatalyst). The protocol for the immobilization and attainment of hybrid SBA-15 particles involves a pre-stage of contact between the catalyst with cocatalyst before their final functionalization. Two zirconocene catalysts are tested in order to attain materials with different microstructural characteristics, molar masses and regioregularities of chains. Some polypropylene chains are able to be accommodated within the silica mesostructure of these composites. Thus, an endothermic event of small intensity appears during heating calorimetric experiments at approximately 105 °C. The existence of these polypropylene crystals, confined within the nanometric channels of silica, is corroborated by SAXS measurements obtained via the change in the intensity and position of the first-order diffraction of SBA-15. The incorporation of silica also has a very significant effect on the rheological response of the resultant materials, leading to important variations in various magnitudes, such as the shear storage modulus, viscosity and δ angle, when a comparison is established with the corresponding neat iPP matrices. Rheological percolation is reached, thus demonstrating the role of SBA-15 particles as filler, in addition to the supporting role that they exert during the polymerizations.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of Content in D Isomer and Incorporation of SBA-15 Silica on the Crystallization Ability and Mechanical Properties in PLLA Based Materials

  • Díez-Rodríguez, Tamara M.
  • Blázquez-Blázquez, Enrique
  • Pérez, Ernesto
  • Cerrada, María L.
Two L-rich polylactides (PLLA) with distinct contents in D isomer and their composites with an intermediate amount of mesoporous Santa Barbara Amorphous-15 (SBA-15) (about 9 wt.%) particles were attained by melt extrusion for the evaluation of the effect of content in D isomer and incorporation of mesoporous silica on the structural PLLA features and on their ultimate mechanical performance. For that, samples have been crystallized under dynamic and isothermal tests (from the melt and from the glassy states). The results from DSC and X-ray diffraction show obtainment of the pure α’ and α modifications at different intervals of crystallization temperature depending on the D steroisomer amount of the PLLA used. Furthermore, several phase transitions are observed depending on the crystallinity reached and the polymorphs developed during the isothermal crystallization from the glass: an additional cold crystallization, the α’/α transformation and the subsequent melting process, appearing all of them at temperatures clearly dependent on the D content. Rigidity, measured through microhardness in amorphous samples, is also affected by the D isomer and the presence of SBA-15 particles. Reinforcement effect of mesoporous silica is relatively more important in the matrix with the highest D content., This work was supported by the Agencia Estatal de Investigación (AEI, Spain) (PID2020-114930GB-I00 project) and ALBA Synchrotron Light Facility. Authors thank the funding. TMDR is also thankful for her pre-doctoral funding (contract number BES-2017-082284)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Composites of a PLA with SBA-15 mesoporous silica: Polymorphism and properties after isothermal cold crystallization

  • Díez-Rodríguez, Tamara M.
  • Blázquez-Blázquez, Enrique
  • Martínez, Juan C.
  • Pérez, Ernesto
  • Cerrada, María L.
Composites based on an L-rich poly(lactic acid), PLA, and different contents in mesoporous SBA-15 silica have been prepared by extrusion in order to evaluate the influence of incorporation of mesoporous particles on the structural PLA features and on their ultimate mechanical performance. For that, the samples have been isothermally cold crystallized for relatively long times at different temperatures, ranging from 65 to 120 °C. The results from DSC, X-ray diffraction and Raman spectroscopy show that the pure α′ modification is obtained at the lower annealing temperatures, while the α form is in majority above 85 °C. The temperature range at which α′ and α polymorphs were developed is somewhat atypical, being associated with the particular D stereoisomer content of the PLA used. Furthermore, several phase transitions are observed depending on the crystallinity reached and the polymorphs developed during the isothermal crystallization from the glass: an additional cold crystallization, the α′/α transformation and the subsequent melting processes. These transitions have been evaluated thoroughly by DSC measurements and real-time variable temperature experiments with synchrotron radiation. It was also found that rigidity of these materials is influenced by both the presence of SBA-15 particles and by the amount and perfection of crystallites. Thus, the relative reinforcement effect of SBA-15 particles is importantly reduced by differences in long spacing PLA values for the materials crystallized between 85 and 120 °C, mainly in the composites with the lowest SBA-15 content. Those are the temperatures where the α polymorph is the major existing crystalline structure., This research was funded by AEI, Spain/FEDER, EU (grant numbers MAT2016-79869-C2-1-P and PID2020-114930GB-I00), by CSIC, Spain (grant number 2020AEP129) and by ALBA Synchrotron Light Facility, Spain. TMDR is also grateful for her pre-doctoral funding (contract number BES-2017-082284). The FESEM, Raman and TGA measure- ments were carried out in the Characterization Service at ICTP-CSIC and authors are grateful for the help and advices received. The synchrotron experiments were performed in the beamline BL11-NCD-SWEET at ALBA Synchrotron Light Facility and authors would like to thank the collaboration and help of ALBA staf
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Nanocomposites of pcl and sba-15 particles prepared by extrusion: Structural characteristics, confinement of pcl chains within sba-15 nanometric channels and mechanical behavior

  • Díez-Rodríguez, Tamara M.
  • Blázquez-Blázquez, Enrique
  • Antunes, N. L. C.
  • Ribeiro, M. Rosario
  • Pérez, Ernesto
  • Cerrada, María L.
A study of different nanocomposites based on poly(ε-caprolactone) (PCL) and mesoporous SBA-15 silica that were prepared by melt extrusion was carried out by analyzing the possible effect of this filler on the crystalline details of PCL, on its mechanical behavior, and on the eventual observation of the confinement of the polymeric chains within the hollow nanometric silica channels. Thus, simultaneous Small-Angle and Wide-Angle X-ray Scattering (SAXS/WAXS) synchrotron experiments at variable temperature were performed on these PCL nanocomposites with different mesoporous silica contents. The importance of the morphological and structural features was assessed by the changes that were observed during the mechanical response of the final materials, which determined that the presence of mesoporous particles leads to a noticeable reinforcing effect., his work was supported by the Agencia Estatal de Investigación (AEI, Spain) together with the European Regional Development Fund (FEDER, UE) (grant numbers MAT2016-79869-C2-1-P and PID2020-114930GB-I00) by CSIC (grant number 2020AEP129) and ALBA Synchrotron Light Facility. TMDR is also grateful for her pre-doctoral funding (contract number BES-2017-08228
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Graphene Nanofibers on the Morphological, Structural, Thermal, Phase Transitions and Mechanical Characteristics in Metallocene iPP Based Nanocomposites

  • Novo, Sandra
  • Fonseca Valero, Carmen
  • Benavente, Rosario
  • Blázquez-Blázquez, Enrique
  • Cerrada, María L.
  • Pérez, Ernesto
Several nanocomposites were prepared by extrusion from a commercial metallocene-type isotactic polypropylene (iPP) and different amounts of two types of graphene (G) nanofibers: ones with a high specific surface, named GHS, and the others with a low specific surface, labeled as GLS. The number of graphene layers was found to be around eight for GLS and about five in the GHS. Scanning electron microscopy (SEM) images of the resultant iPP nanocomposites showed a better homogeneity in the dispersion of the GLS nanofibers within the polymeric matrix compared with the distribution observed for the GHS ones. Crystallinity in the nanocomposites turned out to be dependent upon graphene content and upon thermal treatment applied during film preparation, the effect of the nature of the nanofiber being negligible. Graphene exerted a noticeable nucleating effect in the iPP crystallization. Furthermore, thermal stability was enlarged, shifting to higher temperatures, with increasing nanofiber amount. The mechanical response changed significantly with nanofiber type, along with its content, together with the thermal treatment applied to the nanocomposites. Features of nanofiber surface played a key role in the ultimate properties related to superficial and bulk stiffness., This work was supported by the Agencia Estatal de Investigación (AEI, Spain) (grant number PID2020-114930GB-I00)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Recycling metallocene isotactic polypropylene: the effect ofantioxidants incorporation

  • Blázquez-Blázquez, Enrique
  • Díez-Rodríguez, Tamara M.
  • Pérez, Ernesto
  • Cerrada, María L.
This research was funded by AEI (grant number PID2020-114930GB-I00) and ALBA Synchrotron Light Facility
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A synchrotron SAXS study of PLLA crystallized at different temperatures: One-dimensional correlation functions

  • Díez-Rodríguez, Tamara M.
  • Blázquez-Blázquez, Enrique
  • Martínez, Juan Carlos
  • Cerrada, María L.
  • Pérez, Ernesto
Time-resolved variable-temperature synchrotron techniques have been employed for learning about semicrystalline structure and morphology of an L-rich (4.2 mol% in D-isomer) poly(lactic acid), PLLA. An amorphous specimen has been isothermally crystallized from the glassy state at different temperatures, aiming to gain knowledge about development of the two polymorphs, α′ and α. Subsequent melting of these cold crystallized samples has been analyzed by DSC and synchrotron techniques. Besides studying Lorentz-corrected SAXS profiles, one-dimensional correlation functions have been determined for two crystallization temperatures, selected for yielding neat α′ and α polymorphs respectively. Long spacing, crystal thickness and local crystallinity have been determined. Results show a clear discontinuity with temperature of some of these parameters when transition from disordered α′ to more ordered α modification occurs. Additionally, a SAXS-determined glass transition has been obtained and compared with that derived from the corresponding DSC results., Grant PID2020-114930GB-I00 was funded by MCIN/AEI/10.13039/ 501100011033. Authors acknowledge this support together with that received from ALBA Synchrotron Light Facility. Grant BES-2017-082284 was also funded by MCIN/AEI/10.13039/501100011033 and, thus, TMDR is also thankful for her pre-doctoral funding. The synchrotron experiments were carried out in the beamline BL11-NCD-SWEET at ALBA Synchrotron Light Facility with the collaboration of ALBA staff
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Norbornene as Key for a Possible Efficient Chemical Recycling in Structures Based on Ethylene

  • Calles, Antonio
  • García-Peñas, Alberto
  • Cerrada, María L.
  • Gómez-Elvira González, José Manuel
Different circular strategies attempt to increase the energy efficiency or reduce the accumulation of plastic in landfills through the development of circular polymers. Chemical recycling is essential to recover the initial monomers from plastic residues for obtaining new goods showing the same properties as those using virgin monomers from the initial feedstocks. This work addresses the preparation of poly(ethylene-co-norbornene) copolymers for a promising generation of materials for energy applications that could be treated by chemical recycling. The thermal and thermo-oxidative stability for these copolymers with norbornene is higher than for the neat PE, while their degradation exhibits an activation energy lower than that observed in PE, pointing out that chemical recycling would require a lower energy consumption., This work has been supported by the Madrid Government (Comunidad de Madrid Spain) under the Multiannual Agreement with UC3M (“Fostering Young Doctors Research”, CICLAPNERCM-UC3M), and in the context of the V PRICIT (Research and Technological Innovation Regional Programme). Additionally, this research was supported by the Agencia Estatal de Investigación (AEI, Spain) (grant number PID2020-114930GB-I00)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Recycling of metallocene isotactic polypropylene: importance of antioxidants

  • Blázquez-Blázquez, Enrique
  • Díez-Rodríguez, Tamara M.
  • Pérez, Ernesto
  • Cerrada, María L.
Recycling of plastics is absolutely essential in a circular economy, especially in the case of commodity polymers from fossil resources, like isotactic polypropylene (iPP). Therefore, evaluation of the factors that are decisive for an optimum performance of the recycled based materials becomes mandatory for the obtainment of new products with optimal properties. One of the most important aspects is the protection of the plastics materials not only against the external degradation agents, but also from the radicals generated during their previous service life. Accordingly, several materials have been prepared by extrusion based on virgin iPP with different amounts of the same polypropylene severely degraded, which has been used as model component to be recycled. Previous to the extrusion, a mixture of antioxidants was added to all the samples, and special attention has been paid to consumption of those additives during the extrusion. The results show an increasing reduction of antioxidants with rising content of the degraded material. But, importantly, a rather analogous mechanical response has been found for all the recycled materials in relation to the virgin iPP, pointing out a satisfactory dilution effect of the existing degradation points within the virgin polymeric chains, and indicating the very relevant action of the antioxidants used., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This work was supported by the Agencia Estatal de Investigación (AEI, Spain) (PID2020-114930 GB-I00 project) and ALBA Synchrotron Light Facility. Authors thank the funding. TMDR is also thankful for her pre-doctoral funding (contract number BES-2017-082284).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Synergistic Effect of Mesoporous SBA-15 Particles and Processing Strategy for Improving PLA Crystallization Capability in their Composites

  • Díez-Rodríguez, Tamara M.
  • Blázquez-Blázquez, Enrique
  • Barranco-García, Rosa
  • Pérez, Ernesto
  • Cerrada, María L.
Several composites based on an L-rich poly(lactic acid) (PLA) and mesoporous Santa Barbara Amorphous-15 (SBA-15) are prepared by their addition through two methods: solution-mixed (solvent casting) or melt-mixed (extrusion). Subsequently, films of all the materials are processed by compression molding. The nucleating capacity of silica on PLA crystallization is found to be strongly dependent on protocol used for SBA-15 incorporation. Thus, mesoporous particles induce some PLA ordering in composites when extrusion is used but nucleating ability is much more remarkable when PLA-SBA composites are prepared by SBA-15 addition through casting, PLA crystallization being observed on cooling even at 40 °C min. Crystallinity, crystallization temperature, and polymorphs developed are also dependent on preparation method and cooling rate. Mechanical properties are tested on the just compressed-molded films. At a given SBA-15 content, the melt-mixed composite is less stiff than the solution-mixed material despite both are completely amorphous. Accordingly, microhardness shows a smaller value in the former. For the solution-mixed approach, a partial coating (either external or internal) of the silica particles by PLA chains is suggested to occur during the first preparation stage, enabling a better transfer of reinforcement exerted by SBA-15 silica into the PLA matrix., This research was funded by AEI (grant number PID2020-114930GB-I00), and by ALBA Synchrotron Light Facility. T.M.D.-R. is also grateful for her pre-doctoral funding (contract number BES-2017-082284). Authors are grateful to the Characterization Service at ICTP-CSIC for the SEM facility. The synchrotron experiments were performed at beamline BL11-NCDSWEET at ALBA Synchrotron Light Facility and authors would like to thank the collaboration and help of ALBA staff.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Crosslinked networks in electron beam irradiated polyethylenes evaluated by proton low-field NMR spectroscopy

  • Posadas, Pilar
  • Valentín, Juan L.
  • Benavente, Rosario
  • Blázquez-Blázquez, Enrique
  • Urtiaga, Ane
  • Álvarez, Juan A.
  • Cerrada, María L.
Effect of electron beam (EB) irradiation is analyzed in low and high density polyethylenes (LDPE and HDPE, respectively) at different doses. Parameters as important as degree of crystallinity, melting or crystallization temperatures are dependent on the initial PE molecular architecture, which also controls the gel content developed by action of EB irradiation and the EB dose applied. Thus, this gel amount, ascribed to formation of chain crosslinkings, is raised as irradiation dose increases, being larger in the HDPE than in the LDPE. In both, a plateau value is reached at the highest doses. The molecular changes that take place in both PEs during EB irradiation lead to a hindrance in their crystallization capacity, once macrochains are molten, and, accordingly, to a reduction in crystallinity and to formation of thinner crystallites. Variation with temperature of rigid and soft fractions together with their respective relaxation times is followed in the irradiated LDPE and HDPE specimens by pulse mixed magic-sandwich echo nuclear magnetic resonance (MSE-NMR) measurements. The network structure promoted in these PEs is evaluated by using the multiple-quantum nuclear magnetic resonance (MQ-NMR) approach, showing important differences caused by EB irradiation due to their intrinsic molecular characteristics., Funding received from the 2017 Industrial Doctorate Program of the University of Cantabria, Spain, is gratefully acknowledged. Grants PID2020-119047RB-I00 and PID2020-114930GB-I00 were funded by MCIN/AEI/10.13039/501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A novel approach for preparation of nanocomposites with an excellent rigidity/deformability balance based on reinforced HDPE with halloysite

  • Cecílio, D. M.
  • Cerrada, María L.
  • Pérez, Ernesto
  • Fernandes, A.
  • Lourenço, João P.
  • McKenna, T. F. L.
  • Ribeiro, M. Rosario
An innovative approach, designated as supported activator (SA), allows preparation of high density polyethylene (HDPE)-based highly performant hybrid materials. This procedure makes use of a nano-sized supported methylaluminoxane (MAO)-activator, based on halloysite natural nanotubes (HNT), combined with an in situ supporting concept. The new protocol when compared with a more conventional approach gives rise to higher polymerization activities as well as ultimate materials with better morphological features, greater crystallinity, thicker crystals, and highly increased stiffness. Moreover, a remarkable synergy between rigidity and toughness is attained. The Young's modulus of a film obtained from the nanocomposite with the highest HNT content increases more than 70 % relatively to a pristine HDPE film, while retaining the limit stretching ability of pristine HDPE (more than 800%). A beneficial impact of using a high aspect ratio support such as HNT in the mechanical properties is also observed, when compared to similar HDPE hybrid materials derived from dendrimer-like silica (DS) nanospheres. Interestingly, polymerization activity, polymer features and derived properties found in the ultimate materials are less impacted by support/filler nature than by preparation method. This fact highlights the crucial role of the synthetic methodology used and corroborates the high potential of the SA route for the preparation of high-performance polyethylene-based nanocomposites with an excellent balance between stiffness and deformability., The authors gratefully acknowledge the funding of this work by Fundação para a Ciência e Tecnologia (Project UIDB/00100/2020, Project UIDP/00100/2020 and Project LA/P/0056/2020), the FCT-CATSUS program and PAUILF (Project TC 04/17). D. M. Cecílio’s PhD scholarship (PD/BD/114580/2016) provided by FCT is gratefully acknowledged. A. Fernandes thanks FCT for law DL/57 contract. This work was also supported by the Agencia Estatal de Investigación (AEI, Spain) (Grant No PID2020-114930 GB-I00)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The β form in PVDF nanocomposites with carbon nanotubes: structural features and properties

  • Cerrada, María L.
  • Arranz-Andrés, Javier
  • Caballero-González, Alicia
  • Blázquez-Blázquez, Enrique
  • Pérez, Ernesto
Different amounts of carbon nanotubes (CNT) have been incorporated in materials based on poly(vinylidene fluoride) (PVDF) by solvent blending followed by their further precipitation. Final processing was performed by compression molding. The morphological aspects and crystalline characteristics have been examined, additionally exploring in these nanocomposites the common routes described in the pristine PVDF to induce the β polymorph. This polar β phase has been found to be promoted by the simple inclusion of CNT. Therefore, coexistence of the α and β lattices occurs for the analyzed materials. The real-time variable-temperature X-ray diffraction measurements with synchrotron radiation at a wide angle have undoubtedly allowed us to observe the presence of the two polymorphs and determine the melting temperature of both crystalline modifications. Furthermore, the CNT plays a nucleating role in the PVDF crystallization, and also acts as reinforcement, increasing the stiffness of the nanocomposites. Moreover, the mobility within the amorphous and crystalline PVDF regions is found to change with the CNT content. Finally, the presence of CNT leads to a very remarkable increase in the conductivity parameter, in such a way that the transition from insulator to electrical conductor is reached in these nanocomposites at a percolation threshold ranging from 1 to 2 wt.%, leading to the excellent value of conductivity of 0.05 S/cm in the material with the highest content in CNT (8 wt.%)., This research was funded by MCIN/AEI/10.13039/501100011033, grant number PID2020-114930GB-I00. The authors also acknowledge the support received from ALBA Synchrotron Light Facility., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Antimicrobial Activity and Crystallization Features in Bio-Based Composites of PLLA and MCM-41 Particles Either Pristine or Functionalized with Confined Ag Nanowires

  • Díez-Rodríguez, Tamara M.
  • Blázquez-Blázquez, Enrique
  • Fernández-García, Marta
  • Muñoz-Bonilla, Alexandra
  • Pérez, Ernesto
  • Cerrada, María L.
Composites based on an L-rich poly(lactic acid) (PLLA) and MCM-41, either neat or modified with a silver (MCM-41@Ag), are achieved by solvent casting, being next processed by compression molding. Ag is mainly embedded as nanowires within the hybrid MCM-41@Ag particles, enabling its antimicrobial character. In these composites, the PLLA thermal stability, nucleation efficiency, and mechanical response are dependent on the MCM-41 nature and, to a lesser extent, on its content. Thus, differences in transitions of the PLLA matrix are noticed during cooling at 10 °C/min and in the subsequent heating when composites with neat or modified MCM-41 are compared. A very remarkable nucleation effect is played by pristine MCM-41, being inferior when MCM-41@Ag is incorporated into the PLLA. Wide angle X-ray scattering (WAXS) measurements using synchrotron radiation and performed under variable-temperature conditions in the composites containing MCM-41@Ag indicate that during cold crystallization, the disordered α′ polymorph is initially formed, but it rapidly transforms into ordered α crystals. A long spacing peak, clearly seen in pure PLLA, appears as a small shoulder in PLLAMCM@Ag4 and is undetectable in PLLAMCM@Ag9 and PLLAMCM@Ag20. Furthermore, an increase in MH with the silica content is found in the two sets of composites, the higher MH values being observed in the family of PLLA and MCM-41@Ag. Finally, remarkable antimicrobial features are noticeable in the composites with MCM-41@Ag since this modified silica transfers its biocidal characteristics into the PLLA composites., This research was funded by MCIN/AEI/10.13039/501100011033, grants number PID2020-114930GB-I00 and PID2019-104600RB-I00. The authors also acknowledge the support received from ALBA Synchrotron Light Facility., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Biocidal mesoporous SBA-15 particles decorated with Ag nanowires: Nucleant role in PLLA crystallization and antimicrobial transfer of their activity to the resultant biobased PLLA-SBA15@Ag composites

  • Díez-Rodríguez, Tamara M.
  • Blázquez-Blázquez, Enrique
  • Fernández-García, Marta
  • Muñoz-Bonilla, Alexandra
  • Pérez, Ernesto
  • Cerrada, María L.
Different composites based on an L-rich poly(lactic acid) (PLLA) and mesoporous SBA-15 functionalized with silver (SBA-15@Ag) are prepared by a solvent casting protocol, and subsequently processed as films by compression molding. Characterization of hybrid SBA-15@Ag particles shows that Ag is mainly incorporated as nanowires within the nanometric silica channels, and is able to provide its antimicrobial character to these hybrid particles. PLLA crystallinity, crystallization ability and the polymorphs able to be developed are strongly dependent on cooling rate and in less extent on silica content. These hybrid particles exert an important nucleating and reinforcing effect in the resultant composites. They also show very interesting and remarkable antimicrobial features, which are transferred to the PLLA composites. The most important antimicrobial activity is found against P. aeruginosa, E. coli and C. parapsilosis, Gram negative bacteria and yeast, respectively., Grants PID2020-114930 GB-I00 and PID2019-104600RB-I00 were funded by MCIN/AEI/10.13039/501100011033. Authors acknowledge this support together with that received from ALBA Synchrotron Light Facility. Grant BES-2017-082284 was also funded by MCIN/AEI/ 10.13039/501100011033 and, thus, TMDR is also thankful for her predoctoral funding. The synchrotron experiments were carried out in the beamline BL11-NCD-SWEET at ALBA Synchrotron Light Facility with the collaboration of ALBA staff., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Combined Effects from Dual Incorporation of ATBC as Plasticizer and Mesoporous MCM-41 as Nucleating Agent on the PLA Isothermal Crystallization in Environmentally-Friendly Ternary Composite Systems

  • Blázquez-Blázquez, Enrique
  • Barranco-García, Rosa
  • Díez-Rodríguez, Tamara M.
  • Cerrada, María L.
  • Pérez, Ernesto
Different materials, based on an L-rich polylactide (PLA) as matrix, acetyl tri-n-butyl citrate (ATBC) as plasticizer, and mesoporous Mobile Crystalline Material.41 (MCM-41) particles as nucleating agent, were attained by melt extrusion. These materials are constituted by (a) binary blends of PLA and ATBC with different contents of the latest; (b) a dual compound of PLA and a given amount of MCM-41 silica (5 wt.%); and (c) ternary composites that include PLA, ATBC at several compositions and mesoporous MCM-41 at 5 wt.%. Influence of the incorporation of the plasticizer and nucleating particles has been comprehensively analyzed on the different phase transitions: glass transition, cold crystallization, melt crystallization and melting processes. Presence of both additives moves down the temperature at which PLA phase transitions take place, while allowing the PLA crystallization from the melt at 10 °C/min in the composites. This tridimensional ordering is not noticeable in the pristine PLA matrix and, accordingly, PLA crystallization rate is considerably increased under dynamic conditions and also after isothermal crystallization from either the melt or the glassy state. An important synergistic effect of dual action of ATBC and MCM-41 has been, therefore, found., This research was funded by MCIN/AEI/10.13039/501100011033, grant number PID2020-114930GB-I00. Grant BES-2017-082284 was also funded by MCIN/AEI/10.13039/501100011033 and, thus, TMDR is also thankful for this pre-doctoral funding, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Polypropylene Nanocomposites Attained by In Situ Polymerization Using SBA-15 Particles as Support for Metallocene Catalysts: Effect of Molecular Weight and Tacticity on Crystalline Details, Phase Transitions and Rheological Behavior

  • Barranco-García, Rosa
  • García-Peñas, A.
  • Blázquez-Blázquez, Enrique
  • Ressia, Jorge A.
  • Quinzani, Lidia
  • Vallés, Enrique M.
  • Gómez-Elvira González, José Manuel
  • Pérez, Ernesto
  • Cerrada, María L.
In this study, nanocomposites based on polypropylene are synthesized by the in situ polymerization of propene in the presence of mesoporous SBA-15 silica, which acts as a carrier of the catalytic system (zirconocene as catalyst and methylaluminoxane as cocatalyst). The protocol for the immobilization and attainment of hybrid SBA-15 particles involves a pre-stage of contact between the catalyst with cocatalyst before their final functionalization. Two zirconocene catalysts are tested in order to attain materials with different microstructural characteristics, molar masses and regioregularities of chains. Some polypropylene chains are able to be accommodated within the silica mesostructure of these composites. Thus, an endothermic event of small intensity appears during heating calorimetric experiments at approximately 105 °C. The existence of these polypropylene crystals, confined within the nanometric channels of silica, is corroborated by SAXS measurements obtained via the change in the intensity and position of the first-order diffraction of SBA-15. The incorporation of silica also has a very significant effect on the rheological response of the resultant materials, leading to important variations in various magnitudes, such as the shear storage modulus, viscosity and δ angle, when a comparison is established with the corresponding neat iPP matrices. Rheological percolation is reached, thus demonstrating the role of SBA-15 particles as filler, in addition to the supporting role that they exert during the polymerizations., This research was funded by MCIN/AEI/10.13039/501100011033, grant number PID2020-114930GB-I00, and also by the Madrid Government (Comunidad de Madrid, Spain) under the Multiannual Agreement with UC3M (“Fostering Young Doctors Research”, CICLAPNER-CM-UC3M), and in the context of the V PRICIT (Research and Technological Innovation Regional Programme). R. Barranco-García is recipient of a “Juan de la Cierva” contract (FJC2021-046585-I) funded by MCIN/AEI/10.13039/501100011033 and the European Union “NextGenerationEU”/PRTR. The authors also acknowledge the support received from the ALBA Synchrotron Light Facility., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Detailed microstructure analysis through monomeric insertion modes of poly(propylene-co-norbornene) copolymers and poly(propylene-co-ethylene-co-norbornene) terpolymers with low norbornene contents

  • Fernández Delgado, Sergio
  • García-Peñas, Alberto
  • Serrano, Daniel
  • Cerrada, María L.
  • Gómez-Elvira González, José Manuel
Polypropylene-based thermoplastic elastomers continue to be materials of enormous industrial interest because of their high mechanical performance and durability. These materials are especially important, for instance, in the automotive industry, where these polyolefins accounts for up to 32% of the total plastic used in a car. In the search for new grades, poly(propylene-co-ethylene-co-norbornene) terpolymers might be of interest for the production of a new class of thermoplastic elastomers, whose properties could be tailored by controlling the composition, as well as its distribution. Unfortunately, thorough characterization of these materials has not been possible so far, because of the complexity of their CNMR spectra. In this work, two series of poly(propylene-co-norbornene) copolymers and poly(propylene-co-ethylene-co-norbornene) terpolymers, containing low molar fractions of norbornene and ethylene-norbornene, respectively, have been synthesized and characterized in detail by NMR analysis. The comparison of CNMR spectra in both series and their respective changes with norbornene ratio in the feed enables a complete assignment of signals, which reveals that the terpolymers are featured by a well-defined microstructure, consisting of propylene sequences bound by both PEP triads and well-defined norbornene-ethylene sequences. Such a particular distribution results from an associated insertion of the ethylene and the norbornene that, in addition, accounts for the higher contents of both comonomers, when compared with their respective copolymers, obtained under the same reaction conditions., This work has been supported by the Madrid Government (Comunidad de Madrid Spain) under the Multiannual Agreement with UC3M (“Fostering Young Doctors Research”, CICLAPNER-CMUC3M) in the context of the V PRICIT (Research and Technological Innovation Regional Programme). The grant PID2020-114930 GB-I00, funded by MCIN/AEI/10.13039/501100011033, is also acknowledged, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Improvement of Thermal Protection in Recycled Polyolefins through Hybrid Mesoporous Silica–Antioxidant Particles

  • Blázquez-Blázquez, Enrique
  • Barranco-García, Rosa
  • Díez-Rodríguez, Tamara M.
  • Posadas, Pilar
  • Pérez, Ernesto
  • Cerrada, María L.
The deficient management of plastic waste has caused a serious worldwide environmental problem. Thus, one of the main challenges for the industry in the plastics sector in contributing to sustainability and a circular economy consists of providing a subsequent service life to this waste. For that purpose, the appropriate incorporation of antioxidants will play a key role in preventing or postponing the degradation of plastic waste, where the formation of radicals is initiated during its previous lifetime by the action of degrading agents. Functionalized particles, based on mesoporous MCM-41 silica with Irganox 1076, were prepared with two different protocols and were further incorporated into a material containing virgin PP and 30 wt.% of recycled PP, with the purpose of guaranteeing thermal stability during its next service life. A very significant increase in the thermal stability of the resulting composites was found, attributable to the synergistic action between the Irganox 1076 antioxidant and the MCM-41 particles. In addition, the presence of hybrid particles leads to an important nucleating effect for the crystallization of PP. Moreover, a reinforcing role was also played by these modified mesoporous silicas in the resultant systems. The presented methodology constitutes, therefore, a promising strategy for contributing to the circular economy—since the synergy between the Irganox 1076 antioxidant and MCM-41 particles was found to play an important role in the ultimate performance of recycled polyolefins., This research was funded by MCIN/AEI/10.13039/501100011033, grant number PID2020-114930GB-I00. R. Barranco-García is recipient of a “Juan de la Cierva” contract (FJC2021-046585-I) funded by MCIN/AEI/10.13039/501100011033 and the European Union “Next Generation EU”/PRTR., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermal and Dielectric Stability of Functional Photo-cross-linkableCarbazole-Modified Polypropylene

  • Plaza-González, Daniel
  • Blázquez-Blázquez, Enrique
  • Gómez-Elvira González, José Manuel
  • Hoyos, Mario
The present work deals with the synthesis and characterization of fluorescent polypropylene materials as well as the study of some properties, with the purpose of exploring their potential as specialty materials in high-thermal stability dielectrics. Direct copolymerization of propylene with 9-(undec-10-en-1- yl)-9H-carbazole, via metallocene catalysis, has allowed the preparation of materials containing up to 4 mol % of carbazole units. Characterization of obtained materials has shown that, besides fluorescence emission, improvements in both dielectric response and stability are important enough for potential use in PP-based film capacitors. In addition, an exploratory study on a UV-irradiated copolymer reveals that cross-linking between carbazole units is the mechanism that enables further improvements in thermal and thermo-oxidative stabilities, with respect to polypropylene., The authors gratefully acknowledge the financial support of the Spanish Ministry of Science and Innovation (MCIN) through Project MCIN/AEI/10.13039/501100011033 with Grant Number PID2020-114930GB-I00, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Composites of Poly(3-hydroxybutyrate) and Mesoporous SBA-15 Silica: Crystalline Characteristics, Confinement and Final Properties

  • Díez-Rodríguez, Tamara M.
  • Blázquez-Blázquez, Enrique
  • Pérez, Ernesto
  • Cerrada, María L.
© 2024 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/)., Several composites based on poly(3-hydroxybutyrate) (PHB) and mesoporous SBA-15 silica were prepared by solvent-casting followed by a further stage of compression molding. The thermal stability, phase transitions and crystalline details of these composites were studied, paying special attention to the confinement of the PHB polymeric chains into the mesopores of the silica. For that, differential scanning calorimetry (DSC) and real-time variable-temperature X-ray scattering at small angles (SAXS) were performed. Confinement was stated first by the existence of a small endotherm at temperatures around 20 °C below the main melting or crystallization peak, being later confirmed by a notable discontinuity in the intensity of the main (100) diffraction from the mesoporous silica observed through SAXS experiments, which is related to the change in the scattering contrast before and after the crystallization or melting of the polymer chains. Furthermore, the usual α modification of PHB was developed in all samples. Finally, a preliminary investigation of mechanical and relaxation parameters was carried out through dynamic–mechanical thermal analysis (DMTA). The results show, in the temperature interval analyzed, two relaxations, named α and β (the latest related to the glass transition) in order of decreasing temperatures, in all specimens. The role of silica as a filler is mainly observed at temperatures higher than the glass transition. In such cases, stiffness is dependent on SBA-15 content., This research was funded by MCIN/AEI/10.13039/501100011033, grant number PID2020-114930GB-I00., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Photoactive fluorenyl-functionalized polypropylene for high-performance dielectrics

  • Martín-Lorenzo, Angélica
  • Blázquez-Blázquez, Enrique
  • Gómez-Elvira González, José Manuel
  • Hoyos, Mario
Reducing the impact of polyolefins on the environment is a difficult task not only because of its ubiquity in everyday items, but also because these polymers are used on a massive scale as high-performance materials and such as electronics and automotive. This is the case for polypropylene that behaves as a robust and efficient dielectric in capacitors as a result of its high melting temperature and very low dielectric dissipation factor. The current challenge is to increase its low permittivity, in order to improve energy density and, at the same time, to contribute to the reduction of production, thus progressively increasing the miniaturization of devices. Low content functionalisation has been found to be an efficient route to rise the polypropylene (PP) permittivity, without compromising the mechanical and thermal stability of the material. Recent work has shown that decreasing chain mobility in the amorphous phase is key to maintaining dielectric loss into the low level of PP. This has been achieved by inserting carbazole or N-alkyl pyrrole groups. The former increases the Tg due to their characteristic ¿-¿ stacking interactions and both enable tailored crosslinking, UV and thermally activated respectively. The present study analyses the synthesis and thermal and dielectric stabilities of poly-(propylene-co-9-(undec-10-en-1-yl)-9H-fluorene), with fluorene contents up to 3 mol%, as another example of PP grade that has both enhanced Tg and crosslinking potential under UV radiation. Initial results reveal that these materials have a relative permittivity (¿r) up to 3 and dielectric losses under 0.005. As in the case of carbazole, the strong ¿-¿ stacking between fluorene units improves the thermal, mechanical and dielectric responses and also, that further improvement in stability would be possible under appropriate post-processing irradiation conditions., The authors gratefully acknowledge the financial support of the Spanish Ministry of Science and Innovation (MCIN) through Project MCIN/AEI/10.13039/501100011033 with Grant Number PID2020- 114930GB-I00. A.M. acknowledges to Universidad Nacional de Educación a Distancia (UNED) the tutoring received during her master’s final project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

The mesophase of PLA in binary materials with ATBC and in composites with ATBC and mesoporous MCM-41

  • Blázquez-Blázquez, Enrique
  • Barranco-García, Rosa
  • Díez-Rodríguez, Tamara M.
  • Cerrada, María L.
  • Pérez, Ernesto
Several composites of an L-rich polylactide (PLA) with acetyl tri-n-butyl citrate (ATBC), and mesoporous particles of Mobil Composition of Matter No. 41 (MCM-41) have been prepared in order to overcome the important drawback of PLA related to its rather low crystallization rate. Additionally of solving that deficiency, the mesophase of PLA has been spontaneously formed in two specimens just by standing at room temperature. This f inding was ascertained from the corresponding X-ray diffractograms, which are similar to those observed for the mesophase obtained by stretching experiments. When the mesophase is initially present, its nucleation ability for recrystallization is significantly higher than the one exhibited by amorphous samples, as shown by both DSC and real-time variable-temperature synchrotron diffraction experiments. Moreover, the mesophase displays relatively small values of the long spacing, around 10–11 nm, compared with the values of about 16–18 nm found in the crystals. On the other hand, the mesophase shows in most cases an intermediate degree of order between the amorphous and crystalline phases, as stated by FTIR measurements. Its most characteristic feature is the observation of a distinctive peak at 916 cm 1 , while the crystals show a specific peak at 923 cm and at 921 cm 1 for the α 1 for the α ′ phase modification. The low-frequency region of the spectra below around 800 cm scarcely commented in literature, has also been found especially sensitive to ordering., This research was funded by MCIN/AEI/10.13039/501100011033, grant number PID2020-114930 GB-I00. The synchrotron experiments were carried out in the beamline BL11-NCD-SWEET at the ALBA Synchrotron Light Facility with the collaboration of ALBA staff, to whom the authors are grateful for their support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Use of a nanoplastic carrier for assessing the aquatic toxicity of an organo-phosphite polymer additive

  • Schiano, Marica E.
  • Edo, Carlos
  • Blázquez-Blázquez, Enrique
  • Cerrada, María L.
  • Fernández-Piñas, Francisca
  • Rosa, Roberto
This work reports the production of nanoplastics (NPs) from polypropylene (PP) free of the antioxidant Irgafos® 168 (IRG) and alkane oligomers (ALK). PP pellets were milled into a powder with particle sizes in the 100–500 μ m range. Additives and oligomers were removed using dichloromethane, and the powder exposed to UV irradiation, followed by filtration through 1 μ m filters. PP suspensions, free of antioxidant and oligomers, were reloaded with IRG and ALK to their original commercial concentrations. This approach allowed testing the aquatic toxicity of IRG at concentrations compromised by water solubility limits. Toxicity assays using the cladoceran Daphnia magna with 24–48 h immobilization of neonates as endpoint showed toxicity for NPs containing IRG, with EC 20 (48 h) in the 1.8–3.5 mg/L range, that corresponded to IRG exposure <1.2 pensions of PP containing ALK, but not IRG, exhibited low toxicity (EC 20 μ g/L. Sus> 20 mg/L). The results allowed estimating the toxicity of IRG with a EC 50 value of 3.3 ± 1.1 μ g/L. Assays with different proportions of IRG and its oxidized form showed no differences. This work demonstrated the aquatic toxicity of IRG, for which there were no previous data, and developed a method for testing the toxicity of non-polar additives without being limited by their solubility., The authors acknowledge the financial support provided by the Spanish Government, Ministry of Science, grants PID2020-113769RB- C21/C22, PID2020-114930GB-I00, PLEC2021-007693 and TED2021-131609B-C32/33., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Phase transitions in mixtures based on poly(lactic acid) and two polymeric nucleants processed under a fast or slow cooling from the melt

  • Barranco-García, Rosa
  • Muñoz-Bonilla, Alexandra
  • Cerrada, María L.
  • Echeverría, Coro
  • Fernández-García, Marta
Mixtures based on two different poly(lactic acid)s (PLA) matrices and two distinct nucleating agents, incorporated at several contents, were prepared by extrusion. Furthermore, two thermal treatments were applied during the processing of films from the melt: a quenching (Q) and a slow (S) cooling. Crystalline characteristics of the resultant polymeric systems were mainly triggered by the PLA matrix used and by the cooling rate applied, turning out less important the nature of the nucleant. Thus, stereocomplex crystals were developed almost exclusively in the Q samples while coexistence of homo and stereocomplex crystallites was noticed when slow cooling was imposed. The type of homocrystallites present in the specimens was also dependent on the cooling rate applied during film processing. In the Q systems, crystals were grown on heating through a cold crystallization, as observed by differential scanning calorimetry; while they were developed along the cooling stage in the S materials. Influence of these structural characteristics on mechanical response was also evaluated by microhardness measurements., This work was funded by the Ministerio de Ciencia e Innovación (projects PID2020-114930GB-I00, PID2021-123553OA-I00 and PID2022-136516OB-I00), the Agencia Estatal de Investigación (AEI, Spain) and Fondo Europeo de Desarrollo Regional (FEDER, EU) as well as PTI Salud Global belonging to CSIC. R.B.-G. thanks the Ministerio de Ciencia e Innovación for her Juan de la Cierva contract., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Preparation and characterization of Santa Barbara Amorphous-15 particles functionalized with mercaptopropyl groups and of their composites with poly(lactic acid)

  • Díez-Rodríguez, Tamara M.
  • Blázquez-Blázquez, Enrique
  • Lourenço, João P.
  • Martínez, Juan C.
  • Cerrada, María L.
  • Pérez, Ernesto
Santa Barbara Amorphous-15 (SBA-15) particles functionalized with mercaptopropyl groups (named as SBASH) have been prepared by a synthetic one-pot approach, and then have been incorporated into poly(lactic acid) (PLA), comparing their characteristics with those shown by composites attained with neat SBA-15 (PLASBA). The silica including the mercaptopropyl groups exhibits a certain loss of regularity because of its functionalization, although displays a better interaction with PLA than the pristine SBA-15 particles in the resulting materials. These composites (PLASBASH and PLASBA) also show a thermal stability slightly higher than neat PLA. An important nucleation effect of SBASH silica in the crystallization of PLA has been deduced from cooling experiments as well as from the cold crystallization in heating runs and from the degree of crystallinity reached. Small Angle X-ray Scattering (SAXS) profiles show that the PLA long spacings are rather similar for the different composites and the neat PLA. Thus, crystal size is rather similar in all samples. Microhardness values show an evident effect of reinforcement in all the composites compared with that shown by neat PLA. Nevertheless, the increase in rigidity is smaller in the biobased PLASBASH composites, those containing the modified silica, than in the PLASBA materials with the pristine SBA-15 particles., This research was funded by MCIN/AEI/10.13039/501100011033, grant number PID2020-114930 GB-I00. JPL thanks for funding (Project UIDB/00100/2020). Authors are grateful to the Char- acterization Service at ICTP-CSIC for FESEM, TGA and X-ray diffraction facilities as well as to its personnel for support. The synchrotron ex- periments were carried out in the beamline BL11-NCD-SWEET at the ALBA Synchrotron Light Facility with the collaboration of ALBA staff, to whom the authors are grateful for their support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Aquatic toxicity of UV-irradiated commercial polypropylene plastic particles and associated chemicals

  • Contreras-Castillo, L.
  • Blázquez-Blázquez, Enrique
  • Cerrada, María L.
  • Amariei, G.
  • Rosal, R.
Plastics often contain non-polar chemical additives, such as antioxidants, flame retardants, plasticizers, and UV stabilizers, which improve performance but have poorly understood environmental risks. This study assessed the aquatic toxicity of polypropylene (PP) containing the antioxidant Irgafos 168 (IRG) to the crustacean Daphnia magna and the green alga Raphidocelis subcapitata. Commercial PP containing IRG (PPc) and additive- and oligomer-free PP (PPd) were irradiated at 254 nm using germicidal light, both with and without H2O2. The tested particles included microplastics (MPs, 1–50 μm and 50–500 μm) and nanoplastics (NPs, < 1 μm). The results showed that the toxicity was influenced by particle size, concentration, and the presence of the antioxidant additive. Smaller particles, along with the presence of IRG and its degradation products, tris(2,4-di-tert-butylphenyl) phosphate, bis(2,4-di-tert-butylphenyl) phosphate, and 2,4-di-tert-butylphenol, contributed to higher toxicity in both D. magna and R. subcapitata. The highest toxicity was observed for NPs containing IRG (PPc), which resulted in an EC20 for D. magna immobilization of 7.2 ± 0.1 mg/L, compared to the less toxic NPs free of IRG (EC20 28.7 ± 4.2 mg/L). The growth rate of R. subcapitata was also more affected by NPs generated from PPc (EC20 0.2 ± 1.2 mg/L) than by the corresponding NPs free of IRG (LOEC 3 mg/L). Our findings showed that the main toxicity was driver was an increase of intracellular reactive oxygen species, lipid peroxidation (LPO), damage to cell membrane integrity and impairment of esterase activity. The results demonstrated that irradiated plastic particles act as carriers for toxic non-polar compounds, enhancing negative effects on aquatic organisms, with particle size being a key factor. This study highlights the complex toxicological impacts of micro- and nano-plastics containing additives on aquatic biota., The authors acknowledge the financial support provided by the Spanish Government, Ministry of Science, grants PID2020–113769RB- C21/C22, PID2020–114930GB-I00, PLEC2021–007693 and TED2021–131609B-C32/33. GA thanks to the Spanish Government, Ministry of Science, Innovation and Universities, for her ‘Beatriz Galindo’ BG22/00043 grant and Community of Madrid, grant CM/BG/ 2023–001., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Plastic composition drives the toxicity of UV-aged melamine-polypropylene microplastics, nanoplastics, and leachates on Raphidocelis subcapitata

  • Blázquez-Blázquez, Enrique
  • de Matos, Letícia Paiva
  • Hinge, Mogens
  • Amariei, Georgiana
  • Rosal, Roberto
This study investigates how the plastic additive composition influences the toxicity of UV-aged polypropylene (PP) microplastics (MPs), nanoplastics (NPs) and leachates toward the green alga Raphidocelis subcapitata. Three materials were compared: an antioxidant-deprived additive-free PP (PPd), a base-stabilized PP containing Irgafos 168 (PPc), and a compounded melamine-polypropylene with Irgafos 168 (PPf). UV-irradiation induced surface oxidation and fragmentation across all samples, releasing NPs (< 1 µm) and ultrafiltrates (< 50 kDa), representing the dissolved and colloidal fraction. Characterization by ATR-FTIR, SEM, and GC/MS confirmed that the material deprived of the antioxidant (PPd) underwent more intense oxidation, displaying a higher abundance of oxygenated functional groups and smaller particle sizes compared to stabilized forms. Toxicity assays with R. subcapitata demonstrated a clear size-dependent trend, with ultrafiltrates > NPs > small MPs (1-50 µm) > large MPs (50-500 µm), yet the magnitude of this toxicity was strongly driven by the additive composition. Growth inhibition, reactive oxygen species (ROS) generation, and membrane depolarization were significantly increased in the absence of antioxidant additives across all size fractions, indicating higher bioavailability and reactivity of UV-generated particle surfaces or leached low-molecular-weight oligomers. But still, stabilized melamine-PP released additional leaching products and its ultrafiltrates enriched in oxidized additives and low-molecular-weight oligomers, caused high cytotoxic and oxidative responses. Overall, these results demonstrate that the additive composition not only modulates polymer stability during UV ageing but also governed the toxicity of plastics particles and leaching products toward aquatic primary producers, underscoring the ecological relevance of plastic ageing processes in aquatic ecosystems., The authors acknowledge the financial support provided by the Spanish Government, Ministry of Science, grants PID2020-113769RB- C21/C22, PID2020-114930GB-I00, and PID2024-155145OB-C21. GA thanks to the Spanish Government, Ministry of Science, Innovation and Universities, for her Beatriz Galindo grant and Community of Madrid, grant CM/BG/2023-001. The authors thank ICTS “NANBIOSIS”, UAH (Ciber in Bioengineering, Biomaterials & Nanomedicine, CIBER-BNN) for Confocal Microscopy Service., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Oxidative Stability and Rheological Features in Recycled Composites Based on Postconsumer Polypropylene and Antioxidant-Loaded Silicas

  • Blázquez-Blázquez, Enrique
  • Migler, Kalman B.
  • Díez-Rodríguez, Tamara
  • Cerrada, María L.
  • Pérez, Ernesto
Plastic recycling efforts are hindered by the reduction of material properties in recyclates stemming from oxidative degradation of their polymeric chains. Recent efforts to ameliorate this focus on incorporation of carrier particles functionalized with antioxidants in conjunction with mixing of virgin resin to the recyclates. However, further work is needed to understand how these formulations influence oxidative stability, melt rheology, and crystallization behavior. In the present work, a postconsumer polypropylene (PP) recyclate was blended with approximately 30% by mass virgin PP in conjunction with an antioxidant-loaded nanosized or mesoporous silica. While both silicas prove to be effective antioxidant carriers based on oxidative induction time measurements, the nano-silica shows a clear advantage at the lowest level of particle addition. Small-amplitude rheological measurements show modest enhancements in moduli for the mesoporous composites, indicating good dispersion of these particles, but significant enhancements in moduli are observed at low frequency for the nano-silica materials for concentrations exceeding 2% by mass, indicating sparse network formation. The particles are shown to be also effective nucleating agents for PP, particularly in the presence of flow, but less so for the polyethylene (PE) that is present as a contaminant. Such measurements should prove valuable in optimization of the recycled formulations across the myriad performance and processing parameter space., This work was supported by Ministerio de Ciencia, Innovación y Universidades (PID2020-114930GB-I00)., Peer reviewed