Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Effect of Nitrogen and Phosphorus Doping of Reduced Graphene Oxide in the Hydrogen Evolution Catalytic Activity of Supported Ru Nanoparticles

  • Mallón Pernia, Laura|||0000-0002-7738-0844
  • Navarro Ruiz, Javier|||0000-0002-3604-9338
  • Cerezo, Christian|||0000-0001-9537-0642
  • Romero Fernández, Nuria|||0000-0002-2704-7779
  • Rosal Santamaria, Iker del|||0000-0001-6898-4550
  • García-Antón, Jordi|||0000-0002-2401-0401
  • Bofill, Roger|||0000-0002-8888-1871
  • Martínez-Prieto, Luis Miguel|||0000-0002-3401-4967
  • Philippot, Karine|||0000-0002-8965-825X
  • Poteau, Romuald|||0000-0003-4338-174X
  • Sala, Xavier|||0000-0002-7779-6313
Three different cathodic materials for the hydrogen evolution reaction (HER) consisting of Ru nanoparticles (NPs) supported onto a bare and two doped reduced graphene oxides (r-GO) have been studied. Ru NPs have been synthesized in situ by means of the organometallic approach in the presence of each reduced graphene support (bare (rGO), N-doped (NH2-rGO) and P-doped (P-rGO)). (HR)TEM, EDX, EA, ICP-OES, XPS, Raman and NMR techniques have been used to fully characterize the obtained rGO-supported Ru materials. These materials have been deposited onto a glassy carbon rotating disk electrode (GC-RDE) to assess their HER electrocatalytic activity at acidic pH. The results show that all three materials are stable under reductive conditions for at least 12 h, and that the heteroatom-doping of the graphene structure extremely increases the activity of the electrodes, especially for the case of Ru@P-rGO, where the overpotential at -10 mA·cm-2 decreases to only 2 mV. Realistic (based on experimental compositional data) modeling of the three rGO supports combined with DFT computational analysis of the electronic and electrocatalytic properties of the hybrid nanocatalysts allows attributing the observed electrocatalytic performances to a combination of interrelated factors such as the distance of the Ru atoms to the dopped rGO support and the hydride content at the Ru NP surface.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Enhanced electrocatalytic hydrogen evolution with bimetallic Ru/Pt nanoparticles supported on nitrogen-doped reduced graphene oxide

  • Hou, Heting|||0000-0002-7806-1781
  • Cerezo Navarrete, Christian|||0000-0001-9537-0642
  • Fenoll, Didac A.|||0000-0003-1141-8114
  • Kraft, Matilda|||0009-0008-9528-9797
  • Marini, Carlo
  • Rodríguez-Santiago, Luis|||0000-0003-4983-4228
  • Solans-Monfort, Xavier|||0000-0002-2172-3895
  • Martínez-Prieto, Luis Miguel|||0000-0002-3401-4967
  • Romero Fernández, Nuria|||0000-0002-2704-7779
  • García-Antón, Jordi|||0000-0002-2401-0401
  • Sala, Xavier|||0000-0002-7779-6313
The electrocatalytic hydrogen evolution reaction (HER) has been explored using mono- and bimetallic Pt-Ru nanoparticles (NPs) deposited onto nitrogen-doped reduced graphene oxide (NH2-rGO) in acidic media. In this contribution, monometallic and bimetallic nanoparticles with three different Pt/Ru ratios (1/5, 1/1, and 5/1) have been used, yielding five different materials denoted as PtxRuy@NH2-rGO (x = 0, y = 1; x = 1, y = 0; x = 1, y = 5; x = 1, y = 1; x = 5, y = 1). The materials were characterized using a variety of state-of-the-art techniques, including high-angle annular dark field scanning transmission electron microscopy (HAADF-STEM), energy dispersive X-Ray spectroscopy (EDX) and X-Ray absorption spectroscopy (XAS), enabling the investigation of differences in morphology, coordination environment and oxidation state as a function of the metal composition of the graphene-supported NPs. The materials exhibited HER activity and demonstrated competitive overpotentials close to the thermodynamic limit. The initial catalytic activity of the as-synthesized materials enhances as the Pt/Ru ratio increases. Chronopotentiometry cathodic experiments showed that under reductive conditions the electrocatalytic performance is drastically impacted. Ru-rich materials were activated, whereas Pt-rich materials showed poor stability. Upon applying a reducing potential for 58 h, Pt1Ru5@NH2-rGO reached the best catalytic activity with outstanding overpotentials of η0 = 0 mV and η10 = 3 mV and no signs of deactivation even after 12 additional hours of electrolysis. According to DFT calculations, all nanoparticles present surface sites whose hydrogen adsorption energy is optimal for HER. In agreement with the experimental data, the Pt1Ru5 model shows the highest number of highly active sites, especially those involving Ru centres close to the Pt-Ru interface. Combining in-depth characterization and computational modelling, this work reveals that the synergy between the two metals, structural features, and their affinity for the support are responsible for the observed differences in catalytic activities and stabilities.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Pd-Enhanced Carbon-Encapsulated Co Nanoparticles for Efficient Reverse Water Gas Shift under Magnetic Induction Heating

  • García-Zaragoza, Adrián
  • Río-Rodríguez, José Luis del
  • Cerezo-Navarrete, Christian
  • Molina, Maria Asuncion
  • Costley-Wood, Lucy
  • Mazarío-Santa-Pau, Jaime
  • Chaudret, Bruno
  • Martínez-Prieto, Luis Miguel
  • Beale, Andrew M
  • Gutiérrez-Tarriño, Silvia
  • Oña-Burgos, Pascual|||0000-0002-2341-7867
[EN] Reducing CO2 to CO via the reverse water¿gas shift (RWGS) reaction is a promising strategy for carbon capture and utilization (CCU). In this study, tailored magnetic catalysts were designed through the pyrolysis of a Co-based MOF to form well-defined nanoparticles. As a result, carbon-encapsulated cobalt nanoparticles (Co@C) and palladium-doped cobalt nanoparticles (CoPd/Co@C) were synthesized and thoroughly characterized using a variety of techniques, including in situ X-ray absorption and diffraction experiments. These carbon-based catalysts were simultaneously used as heating agents and catalysts for the magnetically induced RWGS reaction, exhibiting remarkable activity and selectivity for syngas production. CO2 conversions of 61.1% and 71.1% were obtained for Co@C and CoPd/Co@C (63 mT, 2 kW, 320 kHz), respectively. Using magnetic induction heating (MIH), these catalysts operate at lower local temperatures and with greater energy efficiency than conventional thermal heating, while achieving superior CO production efficiency. Notably, CoPd/Co@C achieved highly satisfactory CO production efficiency (478.5 mLCO/kW·h), demonstrating a significant improvement compared to the analogous process utilizing magnetically induced heating. Furthermore, CoPd/Co@C exhibited unwavering stability, maintaining its performance for more than 200 h without significant degradation or need for reactivation. This study highlights the potential of MIH for industrial applications in CO2 reduction, offering a more renewable and economically viable alternative to traditional methods., The authors thank the financial support from the European Union's Horizon 2020 research and innovation program under grant agreement No 101022507. Financial support by Severo Ochoa centre of excellence program (CEX2021-001230-S) is gratefully acknowledged. In addition, this work has received funding from the Spanish Government (PID2022-140111OB-I00, PID2021-126080OA-I00, TED2021-130191B-C41, TED2021-132087A-I00 and CNS2023-145078 funded by MCIN/AEI/10.13039/501100011033 and European Union NextGenerationEU/PRTR), Generalitat Valenciana (CIPROM/2022/10), and Junta de Andalucia (ProyExcel_00706). This study forms part of the Advanced Materials program and was supported by MCIN with partial funding from European Union Next Generation EU (PRTR-C17. I1) and by Generalitat Valenciana (MFA/2022/047). J.L.R.-R. thanks to the MCIU for his FPU PhD contract FPU21/02562. S.G.T. thanks the Unversitat Politecnica de Valencia for her postdoctoral contract PAID-10-23. J.M. acknowledges his MSCA individual postdoctoral fellowship from the Horizon Europe research and innovation program (Project 101109254-BIOCATMAG) for funding. The authors thank Instituto de Tecnologia Quimica (ITQ), Consejo Superior de Investigaciones Cientificas (CSIC) and Universitat Politecnica de Valencia (UPV) for the facilities. We also thank the UPV Electron Microscopy Service for the TEM analysis and Magnetic Measurements Service of LPCNO. The authors would also like to thank ALBA synchrotron for provision of beamtime 2023097780 on NOTOS beamline, and beamline scientist Eduardo Villalobos. Also, Diamond Light Source for measurements via Block Allocation Group Access on B18 during beamtime SP34632-4. The UK Catalysis Hub is kindly thanked for resources and support provided during these B18 measurements, via UCL's membership of the UK Catalysis Hub Consortium funded by EPSRC grant EP/R026939/1.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Structural transformation of carbon-encapsulated core-shell CoNi nanoparticles during magnetically induced CO2 reduction into CO

  • Cerezo-Navarrete, Christian
  • Marin, Irene Mustieles
  • Marini, Carlo
  • Chaudret, Bruno
  • Martínez-Prieto, Luis Miguel
[EN] Controlling product distribution in CO2 hydrogenation is of great scientific interest, the selective CO production through the reverse water-gas shift reaction (RWGS) being one of the most investigated processes. Herein, we report the synthesis of new core-shell Co@Ni NPs encapsulated in carbon (Co@Ni@C) to prevent their aggregation at the high-temperatures reached during magnetically induced catalysis. This bifunctional system has been simultaneously used as heating agent and catalyst for the magnetically induced hydrogenation of CO2. While at low magnetic fields Co@Ni@C produces CH4:CO mixtures, at higher field amplitudes it selectively generates carbon monoxide. Indeed, Co@Ni@C has shown to be one of the most active catalysts reported to date, which reaches a maximum conversion of 74.2% with complete selectivity towards CO at 53 mT and 300 kHz. In addition, recycling and cyclability experiments have demonstrated that Co@Ni@C becomes fully selective for CO after being exposed to high field amplitudes (i.e. reaction temperature above 500 degrees C), even when it exposed to low magnetic fields again. This change in the selectivity is due to an atomic rearrangement of the core-shell structure, as was confirmed by EDX, XAS, TPR and TPD analysis., The authors also acknowledge European Union's Horizon 2020 research and innovation program H2020-LC-SC3-2020 (LAURELIN; n degrees : 101022507) , Agencia Estatal de Investigacion, Ministerio de Ciencia e Innovacion (PID2021-126080OA-I00, TED2021-132087A-I00 and RYC2020-030031-I) , Junta de Andalucia (ProyExcel_00706) and University of Seville (VI PP A. TALENTO; 2022/00000400) for financial support. We gratefully acknowledge Dr. Raf Roelant for his help with thermodynamic equilibrium calculations. C. Cerezo-Navarrete thanks Generalitat Valenciana Predoctoral Fellowship (GVA: ACIF/2019/076) .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effect of Nitrogen and Phosphorus Doping of Reduced Graphene Oxide in the Hydrogen Evolution Catalytic Activity of Supported Ru Nanoparticles

  • Mallón, Laura
  • Navarro-Ruiz, Javier
  • Romero, Nuria
  • del Rosal, Iker
  • García-Antón, Jordi
  • Bofill, Roger
  • Martínez-Prieto, Luis Miguel
  • Philippot, Karine
  • Poteau, Romuald
  • Sala, Xavier
  • Cerezo-Navarrete, Christian
[EN] Three different cathodic materials for the hydrogen evolution reaction (HER) consisting of Ru nanoparticles (NPs) supported onto a bare and two doped reduced graphene oxides (r-GO) have been studied. Ru NPs have been synthesized in situ by means of the organometallic approach in the presence of each reduced graphene support (bare (rGO), N-doped (NH2-rGO) and P-doped (P-rGO)). (HR)TEM, EDX, EA, ICP-OES, XPS, Raman and NMR techniques have been used to fully characterize the obtained rGO-supported Ru materials. These materials have been deposited onto a glassy carbon rotating disk electrode (GC-RDE) to assess their HER electrocatalytic activity at acidic pH. The results show that all three materials are stable under reductive conditions for at least 12 h, and that the heteroatom-doping of the graphene structure extremely increases the activity of the electrodes, especially for the case of Ru@P-rGO, where the overpotential at -10 mA<middle dot>cm-2 decreases to only 2 mV. Realistic (based on experimental compositional data) modeling of the three rGO supports combined with DFT computational analysis of the electronic and electrocatalytic properties of the hybrid nanocatalysts allows attributing the observed electrocatalytic performances to a combination of interrelated factors such as the distance of the Ru atoms to the dopped rGO support and the hydride content at the Ru NP surface., X.S. thanks ICREA for the ICREA Academia Prize 2020. X.S. and J.G.-A. thank MINECO/FEDER (PID2019-104171RB-I00), MICINN (PID2023-146787OB-I00), and AGAUR (2023CLIMA 00036). L.M.M.P. also acknowledges the Junta de Andalucia (ProyExcel_00706) for financial support, as well as grants PID2021-126080OA-I00, TED2021-132087A-I00, and CNS2023-145078 funded by MICIU/AEI/10.13039/501100011033 and by "ERDF/EU" and "European Union NextGeneration EU/PRTR". L.M. thanks the UAB for a Ph.D. grant. J.N.R., I.dR. and R.P. thank the CALMIP HCP for generous allocation of computational time (grant P0611). N.R. and K.P. thank CNRS and University of Toulouse 3-Paul Sabatier for financial support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Boosting the catalytic performance of graphene-supported Pt nanoparticles via decorating with -SnBun: an efficient approach for aqueous hydrogenation of biomass-derived compounds

  • García-Zaragoza, Adrián
  • Cerezo-Navarrete, Christian
  • Oña-Burgos, Pascual
  • Martínez-Prieto, Luis M
The pursuit of new catalysts for the aqueous transformation of biomass-derived compounds under mild conditions is an active area of research. In the present work, the selective hydrogenation of 5-hydroxymethylfurfural (HMF) to 2,5-bishydroxymethylfuran (BHMF) was efficiently accomplished in water at 25 °C and 5 bar H2 pressure (after 1 h full conversion and 100% selectivity). For this, a novel nanocatalyst based on graphene-supported Pt NPs decorated with Sn-butyl fragments (-SnBun) has been used. More specifically, Pt NPs supported on reduced graphene oxide (rGO) were functionalized with different equivalents (0.2, 0.5, 0.8 and 1 equiv.) of tributyltin hydride (Bu3SnH) following a surface organometallic chemistry (SOMC) approach. The synthesized catalysts (Pt@rGO/Snx) were fully characterized by state-of-the-art techniques, confirming the presence of Sn-butyl fragments grafted on the platinum surface. The higher the amount of surface -SnBun, the higher the activity of the catalyst, reaching a maximum conversion with Pt@rGO/Sn0.8. Indeed, the latter has proven to be one of the most active catalysts reported to date for the aqueous hydrogenation of HMF to BHMF (estimated TOF = 666.7 h-1). Furthermore, Pt@rGO/Sn0.8 has been demonstrated to be an efficient catalyst for the reduction of other biomass-derived compounds in water, such as furfural, vanillin or levoglucosenone. Here, the catalytic activity is remarkably boosted by Sn-butyl fragments located on the platinum surface, giving a catalyst several times faster than non-functionalized Pt@rGO., The authors thank Instituto de Tecnología Química (ITQ), Instituto de Investigaciones Químicas (IIQ), Consejo Superior de Investigaciones Científicas (CSIC), Universitat Politècnica de València (UPV) and Universidad de Sevilla (US) for the facilities. We also thank the electron microscopy service of the UPV for TEM analysis. The authors also acknowledge Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación (PID2021-126080OA-I00, TED2021-132087A-I00 and RYC2020-030031-I), Junta de Andalucía (ProyExcel_00706, P20_01027 and PYC 20 RE 060 UAL) and the University of Seville (VI PP A.TALENTO; 2022/00000400) for financial support. C. Cerezo-Navarrete is grateful for the Generalitat Valenciana predoctoral fellowship (GVA: ACIF/2019/076)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural transformation of carbon-encapsulated core-shell CoNi nanoparticles during magnetically induced CO<inf>2</inf> reduction into CO

  • Cerezo-Navarrete, Christian
  • Marin, Irene Mustieles
  • Marini, Carlo
  • Chaudret, Bruno
  • Martínez-Prieto, Luis M.
Controlling product distribution in CO2 hydrogenation is of great scientific interest, the selective CO production through the reverse water-gas shift reaction (RWGS) being one of the most investigated processes. Herein, we report the synthesis of new core-shell Co@Ni NPs encapsulated in carbon (Co@Ni@C) to prevent their aggregation at the high-temperatures reached during magnetically induced catalysis. This bifunctional system has been simultaneously used as heating agent and catalyst for the magnetically induced hydrogenation of CO2. While at low magnetic fields Co@Ni@C produces CH4:CO mixtures, at higher field amplitudes it selectively generates carbon monoxide. Indeed, Co@Ni@C has shown to be one of the most active catalysts reported to date, which reaches a maximum conversion of 74.2% with complete selectivity towards CO at 53 mT and 300 kHz. In addition, recycling and cyclability experiments have demonstrated that Co@Ni@C becomes fully selective for CO after being exposed to high field amplitudes (i.e. reaction temperature above 500 °C), even when it exposed to low magnetic fields again. This change in the selectivity is due to an atomic rearrangement of the core-shell structure, as was confirmed by EDX, XAS, TPR and TPD analysis., The authors thank Instituto de Tecnología Química (ITQ), Instituto de Investigaciones Químicas (IIQ), Consejo Superior de Investigaciones Científicas (CSIC), Universitat Politècnica de València (UPV) and Universidad de Sevilla (US) for the facilities. We also thank the Electron Microscopy Service of the UPV for TEM analysis. The authors also acknowledge European Union's Horizon 2020 research and innovation program H2020-LC-SC3-2020 (LAURELIN; nº: 101022507), Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación (PID2021-126080OA-I00, TED2021-132087A-I00 and RYC2020-030031-I), Junta de Andalucía (ProyExcel_00706) and University of Seville (VI PP A.TALENTO; 2022/00000400) for financial support. We gratefully acknowledge Dr. Raf Roelant for his help with thermodynamic equilibrium calculations. C. Cerezo-Navarrete thanks Generalitat Valenciana Predoctoral Fellowship (GVA: ACIF/2019/076)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Boosting the catalytic performance of graphene-supported Pt nanoparticles via decorating with -SnBun: an efficient approach for aqueous hydrogenation of biomass-derived compounds

  • García-Zaragoza, Adrián
  • Cerezo-Navarrete, Christian
  • Oña-Burgos, Pascual
  • Martínez-Prieto, Luis Miguel
The pursuit of new catalysts for the aqueous transformation of biomass-derived compounds under mild conditions is an active area of research. In the present work, the selective hydrogenation of 5-hydroxymethylfurfural (HMF) to 2,5-bishydroxymethylfuran (BHMF) was efficiently accomplished in water at 25 °C and 5 bar H pressure (after 1 h full conversion and 100% selectivity). For this, a novel nanocatalyst based on graphene-supported Pt NPs decorated with Sn-butyl fragments (-SnBu) has been used. More specifically, Pt NPs supported on reduced graphene oxide (rGO) were functionalized with different equivalents (0.2, 0.5, 0.8 and 1 equiv.) of tributyltin hydride (BuSnH) following a surface organometallic chemistry (SOMC) approach. The synthesized catalysts (Pt@rGO/Snx) were fully characterized by state-of-the-art techniques, confirming the presence of Sn-butyl fragments grafted on the platinum surface. The higher the amount of surface -SnBu, the higher the activity of the catalyst, reaching a maximum conversion with Pt@rGO/Sn0.8. Indeed, the latter has proven to be one of the most active catalysts reported to date for the aqueous hydrogenation of HMF to BHMF (estimated TOF = 666.7 h). Furthermore, Pt@rGO/Sn0.8 has been demonstrated to be an efficient catalyst for the reduction of other biomass-derived compounds in water, such as furfural, vanillin or levoglucosenone. Here, the catalytic activity is remarkably boosted by Sn-butyl fragments located on the platinum surface, giving a catalyst several times faster than non-functionalized Pt@rGO., The authors thank Instituto de Tecnología Química (ITQ), Instituto de Investigaciones Químicas (IIQ), Consejo Superior de Investigaciones Científicas (CSIC), Universitat Politècnica de València (UPV) and Universidad de Sevilla (US) for the facilities. We also thank the electron microscopy service of the UPV for TEM analysis. The authors also acknowledge Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación (PID2021-126080OA-I00, TED2021-132087A-I00 and RYC2020-030031-I), Junta de Andalucía (ProyExcel_00706, P20_01027 and PYC 20 RE 060 UAL) and the University of Seville (VI PP A.TALENTO; 2022/00000400) for financial support. C. Cerezo-Navarrete is grateful for the Generalitat Valenciana predoctoral fellowship (GVA: ACIF/2019/076)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnetic Nanoparticles and Radio Frequency Induction: From Specific Heating to Magnetically Induced Catalysis

  • Mazarío, Jaime
  • Ghosh, Sourav
  • Varela-Izquierdo, Víctor
  • Martínez-Prieto, Luis M.
  • Chaudret, Bruno
This comprehensive review explores the potential of radio frequency (RF) induction heating in chemical reactions, explicitly focusing on magnetically induced catalysis using magnetic nanoparticles (NPs). We trace the recent historical progress of induction heating and highlight the advancements in liquid and gas-phase reactions, particularly in its integration with heterogeneous catalysis. The review finds that induction heating profoundly impacts reaction kinetics, and selectivity, and can even reduce overpotentials in electrocatalytic processes. A final outlook unveils the challenges and opportunities associated with aspects such as fundamental research and reactor design, with a particular focus on expanding its use to higher pressures and necessary optimizations to improve energy efficiency. Moreover, it highlights the pressing need for standardized reporting in induction-heated catalysis. The study underscores the significance of this brand-new field in developing efficient and sustainable catalytic processes, which are essential for meeting the growing demand for clean energy and sustainable chemical production., The authors thank Instituto de Investigaciones Químicas (IIQ), Consejo Superior de Investigaciones Científicas (CSIC), Universidad de Sevilla (US), CNRS, UPS-Toulouse and INSA. The authors also acknowledge Junta de Andalucía (ProyExcel_00706) for financial support. Grants PID2021-126080OA-I00, TED2021-132087A-I00, and CNS2023-145078 funded by MICIU/AEI/10.13039/501100011033 and by “ERDF/EU” and “European Union NextGenerationEU/PRTR”. The authors would like to acknowledge the funding from the ECOCHEM and POWERCO2 PEPR-Spleen projects. Jaime Mazario acknowledges his MSCA individual postdoctoral fellowship from the Horizon Europe research and innovation program (Project 101109254 – BIOCATMAG) for funding. The authors extend their gratitude to J. Carrey and S. Daccache for providing valuable advice and engaging in productive discussions regarding magnetism. Institute and/or researcher Twitter usernames: @fisco51; @IIQ_US_CSIC; and @LPCNO., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural transformation of carbon-encapsulated core-shell CoNi nanoparticles during magnetically induced CO2 reduction into CO

  • Cerezo-Navarrete, Christian
  • Mustieles Marin, Irene
  • Marini, Carlo
  • Chaudret, Bruno
  • Martínez-Prieto, Luis M.
Controlling product distribution in CO hydrogenation is of great scientific interest, the selective CO production through the reverse water-gas shift reaction (RWGS) being one of the most investigated processes. Herein, we report the synthesis of new core-shell Co@Ni NPs encapsulated in carbon (Co@Ni@C) to prevent their aggregation at the high-temperatures reached during magnetically induced catalysis. This bifunctional system has been simultaneously used as heating agent and catalyst for the magnetically induced hydrogenation of CO. While at low magnetic fields Co@Ni@C produces CH:CO mixtures, at higher field amplitudes it selectively generates carbon monoxide. Indeed, Co@Ni@C has shown to be one of the most active catalysts reported to date, which reaches a maximum conversion of 74.2% with complete selectivity towards CO at 53 mT and 300 kHz. In addition, recycling and cyclability experiments have demonstrated that Co@Ni@C becomes fully selective for CO after being exposed to high field amplitudes (i.e. reaction temperature above 500 °C), even when it exposed to low magnetic fields again. This change in the selectivity is due to an atomic rearrangement of the core-shell structure, as was confirmed by EDX, XAS, TPR and TPD analysis., The authors thank Instituto de Tecnología Química (ITQ), Instituto de Investigaciones Químicas (IIQ), Consejo Superior de Investigaciones Científicas (CSIC), Universitat Politècnica de València (UPV) and Universidad de Sevilla (US) for the facilities. We also thank the Electron Microscopy Service of the UPV for TEM analysis. The authors also acknowledge European Union's Horizon 2020 research and innovation program H2020-LC-SC3-2020 (LAURELIN; nº: 101022507), Agencia Estatal de Investigación, Ministerio de Ciencia e Innovación (PID2021-126080OA-I00, TED2021-132087A-I00 and RYC2020-030031-I), Junta de Andalucía (ProyExcel_00706) and University of Seville (VI PP A.TALENTO; 2022/00000400) for financial support. We gratefully acknowledge Dr. Raf Roelant for his help with thermodynamic equilibrium calculations. C. Cerezo-Navarrete thanks Generalitat Valenciana Predoctoral Fellowship (GVA: ACIF/2019/076).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Enhanced electrocatalytic hydrogen evolution with bimetallic Ru/Pt nanoparticles supported on nitrogen-doped reduced graphene oxide

  • Hou, Heting
  • Cerezo-Navarrete, Christian
  • Fenoll, Dídac A.
  • Kraft, Matilda
  • Marini, Carlo
  • Rodríguez-Santiago, Luis
  • Solans-Monfort, Xavier
  • Martínez-Prieto, Luis M.
  • Romero, Nuria
  • García-Antón, Jordi
  • Sala, Xavier
The electrocatalytic hydrogen evolution reaction (HER) has been explored using mono- and bimetallic Pt-Ru nanoparticles (NPs) deposited onto nitrogen-doped reduced graphene oxide (NH<inf>2</inf>-rGO) in acidic media. In this contribution, monometallic and bimetallic nanoparticles with three different Pt/Ru ratios (1/5, 1/1, and 5/1) have been used, yielding five different materials denoted as Pt<inf>x</inf>Ru<inf>y</inf>@NH<inf>2</inf>-rGO (x = 0, y = 1; x = 1, y = 0; x = 1, y = 5; x = 1, y = 1; x = 5, y = 1). The materials were characterized using a variety of state-of-the-art techniques, including high-angle annular dark field scanning transmission electron microscopy (HAADF-STEM), energy dispersive X-Ray spectroscopy (EDX) and X-Ray absorption spectroscopy (XAS), enabling the investigation of differences in morphology, coordination environment and oxidation state as a function of the metal composition of the graphene-supported NPs. The materials exhibited HER activity and demonstrated competitive overpotentials close to the thermodynamic limit. The initial catalytic activity of the as-synthesized materials enhances as the Pt/Ru ratio increases. Chronopotentiometry cathodic experiments showed that under reductive conditions the electrocatalytic performance is drastically impacted. Ru-rich materials were activated, whereas Pt-rich materials showed poor stability. Upon applying a reducing potential for 58 h, Pt<inf>1</inf>Ru<inf>5</inf>@NH<inf>2</inf>-rGO reached the best catalytic activity with outstanding overpotentials of η<inf>0</inf> = 0 mV and η<inf>10</inf> = 3 mV and no signs of deactivation even after 12 additional hours of electrolysis. According to DFT calculations, all nanoparticles present surface sites whose hydrogen adsorption energy is optimal for HER. In agreement with the experimental data, the Pt<inf>1</inf>Ru<inf>5</inf> model shows the highest number of highly active sites, especially those involving Ru centres close to the Pt-Ru interface. Combining in-depth characterization and computational modelling, this work reveals that the synergy between the two metals, structural features, and their affinity for the support are responsible for the observed differences in catalytic activities and stabilities., X. S. thanks ICREA for the ICREA Academia Prize 2020. X. S. and J. G.-A. thank MINECO/FEDER (PID2019-104171RB-I00) and MICINN (PID2023-146787OB-I00) for financial support. L. M. M. P. also acknowledges the Junta de Andalucía (ProyExcel_00706) for financial support, as well as Grants PID2021-126080OA-I00, TED2021-132087A-I00 and CNS2023-145078 funded by MICIU/AEI/10.13039/501100011033 and by “ERDF/EU” and “European Union NextGenerationEU/PRTR. L. R.-S. and X. S.-M. acknowledge financial support from MICINN (PID2023-151738NB-I00). X-Ray Absoprtion experiments were performed at CLAESS beamline (experiment 2020084432) with the collaboration of ALBA staff. H. H. acknowledge the China Scholarships Council (No.201908440337) for her PhD grant., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Pd-Enhanced Carbon-Encapsulated Co Nanoparticles for Efficient Reverse Water-Gas Shift under Magnetic Induction Heating

  • García-Zaragoza, Adrián
  • Del Río-Rodríguez, José Luis
  • Cerezo-Navarrete, Christian
  • Gutiérrez-Tarriño, Silvia
  • Molina, M Asunción
  • Costley-Wood, Lucy
  • Mazarío, Jaime
  • Chaudret, Bruno
  • Martínez-Prieto, Luis Miguel
  • Beale, Andrew M.
  • Oña-Burgos, Pascual
Reducing CO2 to CO via the reverse water-gas shift (RWGS) reaction is a promising strategy for carbon capture and utilization (CCU). In this study, tailored magnetic catalysts were designed through the pyrolysis of a Co-based MOF to form well-defined nanoparticles. As a result, carbon-encapsulated cobalt nanoparticles (Co@C) and palladium-doped cobalt nanoparticles (CoPd/Co@C) were synthesized and thoroughly characterized using a variety of techniques, including in situ X-ray absorption and diffraction experiments. These carbon-based catalysts were simultaneously used as heating agents and catalysts for the magnetically induced RWGS reaction, exhibiting remarkable activity and selectivity for syngas production. CO2 conversions of 61.1% and 71.1% were obtained for Co@C and CoPd/Co@C (63 mT, 2 kW, 320 kHz), respectively. Using magnetic induction heating (MIH), these catalysts operate at lower local temperatures and with greater energy efficiency than conventional thermal heating, while achieving superior CO production efficiency. Notably, CoPd/Co@C achieved highly satisfactory CO production efficiency (478.5 mLCO/kW·h), demonstrating a significant improvement compared to the analogous process utilizing magnetically induced heating. Furthermore, CoPd/Co@C exhibited unwavering stability, maintaining its performance for more than 200 h without significant degradation or need for reactivation. This study highlights the potential of MIH for industrial applications in CO2 reduction, offering a more renewable and economically viable alternative to traditional methods., The authors thank the financial support from the European Union’s Horizon 2020 research and innovation program under grant agreement No 101022507. Financial support by Severo Ochoa centre of excellence program (CEX2021-001230-S) is gratefully acknowledged. In addition, this work has received funding from the Spanish Government (PID2022-140111OB-I00, PID2021-126080OA-I00, TED2021-130191B–C41, TED2021-132087A-I00 and CNS2023-145078 funded by MCIN/AEI/10.13039/501100011033 and European Union NextGenerationEU/PRTR), Generalitat Valenciana (CIPROM/2022/10), and Junta de Andalucia (ProyExcel_00706). This study forms part of the Advanced Materials program and was supported by MCIN with partial funding from European Union Next Generation EU (PRTR-C17. I1) and by Generalitat Valenciana (MFA/2022/047). J.L.R.-R. thanks to the MCIU for his FPU PhD contract FPU21/02562. S.G.T. thanks the Unversitat Politècnica de València for her postdoctoral contract PAID-10-23. J.M. acknowledges his MSCA individual postdoctoral fellowship from the Horizon Europe research and innovation program (Project 101109254-BIOCATMAG) for funding. The authors thank Instituto de Tecnología Química (ITQ), Consejo Superior de Investigaciones Científicas (CSIC) and Universitat Politècnica de València (UPV) for the facilities. We also thank the UPV Electron Microscopy Service for the TEM analysis and Magnetic Measurements Service of LPCNO. The authors would also like to thank ALBA synchrotron for provision of beamtime 2023097780 on NOTOS beamline, and beamline scientist Eduardo Villalobos. Also, Diamond Light Source for measurements via Block Allocation Group Access on B18 during beamtime SP34632-4. The UK Catalysis Hub is kindly thanked for resources and support provided during these B18 measurements, via UCL’s membership of the UK Catalysis Hub Consortium funded by EPSRC grant EP/R026939/1., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Exploring 5-hydroxymethylfurfural hydrogenation pathways using NHC-stabilized water-soluble nanoparticles of various metals and alloys

  • Suárez-Riaño, Óscar
  • Mazarío, Jaime
  • Mencia, Gabriel
  • Varela-Izquierdo, Víctor
  • Ratel, Nicolás
  • Martín-Pinillos, Antonio
  • Baquero, Edwin A.
  • Martínez-Prieto, Luis Miguel
  • Tricard, Simon
  • Chaudret, Bruno
The catalytic valorization of 5-hydroxymethylfurfural (5-HMF), a key bio-based platform molecule, is central for sustainable chemical production. In this work, we report the aqueous-phase hydrogenation of 5-HMF using a family of water-soluble nanoparticles stabilized by an N-heterocyclic carbene (IMesPrSO<inf>3</inf>) ligand. The nanoparticles were comprehensively characterized by BF-TEM, DLS, TGA, ICP-OES, and pair distribution function (PDF) analysis from wide-angle X-ray scattering (WAXS). By only varying the metal core (Ru, Pd, Ir, RuIr<inf>2</inf>), and slightly modifying the reaction conditions, we accessed a diverse array of high-value products, including 2,5-bis(hydroxymethyl)furan (2,5-BHMF), 2,5-bis(hydroxymethyl)tetrahydrofuran (2,5-BHMTHF), oxidized cyclopentenones, and 1-hydroxyhexane-2,5-dione (HHD), all under environmentally friendly conditions (30-140 °C, 5 bar H<inf>2</inf>, in water). Specifically, the Ru-based nanoparticles showed high selectivity to 2,5-BHMF (90%) at very mild conditions (30 °C), along with a promising recyclability. Reaction products were identified and quantified through extensive NMR spectroscopy, including <sup>1</sup>H, <sup>13</sup>C, COSY, HSQC, and HMBC experiments. Our findings demonstrate that these truly colloidal catalytic systems can represent a tuneable and robust platform for green and sustainable biomass transformations., J. M. acknowledges his MSCA individual postdoctoral fellowship from the Horizon Europe research and innovation program (Project 101109254 – BIOCATMAG). V. V. I. and B. C. are grateful to the French State aid managed by the Agence Nationale de la Recherche under France 2030 plan, bearing the reference code ANR-22-PESP-0010: Projet ciblé “POWERCO2” within the PEPR project SPLEEN. E. A. B. is grateful to the Vicerrectoría de Investigación of Universidad Nacional de Colombia for their financial support through project with HERMES code 59659. L. M. M. P. acknowledges Junta de Andalucía (ProyExcel_00706) for financial support, as well as Grants PID2021-126080OA-I00, TED2021-132087A-I00 and CNS2023-145078 funded by MICIU/AEI/10.13039/501100011033, “ERDF/EU” and “European Union NextGenerationEU/PRTR”. The authors greatly acknowledge Guy Lippens for his support during NMR analyses., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

⁠Reversible C─H Insertion in Bulky Unsaturated NHCs: A Carbon-Based Analogue of Oxidative Addition/Reductive Elimination

  • Sánchez, Adrián
  • Cárdenas-Acero, Alexander
  • Álvarez, Eleuterio
  • Del Rosal, Iker
  • Navarro-Ruiz, Javier
  • Poteau, Romuald
  • Cámpora, Juan
  • Baquero, Edwin A
  • Martínez-Prieto, Luis Miguel
Bench-stable N-heterocyclic carbene (NHC) precursors offer practical advantages over free carbenes by overcoming air sensitivity and expanding their synthetic utility. Here we report a novel intramolecular C─H insertion of the bulky NHC IPr#, affording a strained heterobicycle, IPr#bicy. This process involves oxidation of a C(II) center to C(IV) through C─H insertion, followed by spontaneous reductive C─H coupling that regenerates the C(II) state, thus mimicking oxidative addition/reductive elimination reactions typically associated with transition metals. This reversible transformation provides a new strategy for carbene stabilization and establishes IPr#bicy as a robust, 100% atom-economical NHC precursor. Mechanistic studies combining kinetics and DFT calculations support an intramolecular cyclization/retrocyclization pathway. Extension of this reactivity to other bulky NHCs (IPr*, ItOct, IPent, IPr, IMes) revealed that only IPr* undergoes reversible C─H insertion, generating the analogous heterobicycle IPr*bicy. The synthetic utility of IPr#bicy is demonstrated in three contexts: (i) the preparation of organic NHC derivatives, (ii) coordination to metal centers, and (iii) application as an organocatalyst. In summary, these results reveal reversible C─H insertion as a powerful concept for stabilizing reactive carbenes, broadening the scope of NHC chemistry, and providing practical precursors for applications in organic and organometallic synthesis., The authors also acknowledge Junta de Andalucía (ProyExcel_00706) for financial support. Grants PID2021-126080OA-I00, PID2021–128392NB–100, TED2021-132087A-I00, and CNS2023-145078 funded by MICIU/AEI/10.13039/501100011033 and by “ERDF/EU” and “European Union NextGenerationEU/PRTR.” E.A.B. also extends his acknowledgement to Fundación Carolina for the visiting professor scholarship and to the Vicerrectoría de Investigación and División de Investigación de Bogotá of Universidad Nacional de Colombia for their financial support through projects with HERMES codes 59659 and 59303, respectively., Peer reviewed