Pasar al contenido principal

VALORIZACION DE DIOXIDO DE CARBONO CON HIDROGENO VERDE PRODUCIENDO METANO O ACIDO FORMICO MEDIANTE INNOVACION EN INGENIERIA DE NANOMATERIALES

PID2023-146481OB-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2023
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Effect of Cs and Ba promoters on Ni/graphite catalysts for CO2 conversion via the reverse water gas shift reaction

  • Moral Pombo, Jorge
  • Conesa, José María
  • Campos Castellanos, Eduardo
  • García-Bordejé, José Enrique
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
12 figures, 2 tables., Obtaining syngas from CO2 and green hydrogen via the reverse water gas shift (RWGS) reaction is a promising strategy for mitigating the greenhouse effect. Additionally, CO obtained as the product holds significant potential in the syngas-based chemical industry. In this context, we developed efficient Ni-based catalysts for the RWGS reaction at a low temperature. In our approach, we selected Cs and Ba as catalytic promoters and utilized high-surface-area graphite (HSAG400) as a support to maximize the interaction between the metal and promoter. Our study revealed that both promoters helped in enhancing the CO2 conversion but had opposite effects in the RWGS reaction. In particular, the use of the Cs promoter boosted the CO selectivity up to 95%, while the addition of Ba proved to be detrimental to CO selectivity., This work was funded by MICIU/AEI/https://doi.org/10.13039/501100011033 and by FEDER, UE through grant PID2023 146481OB-I00 and by Gobierno de Aragón (Grupo Reconocido DGA T03_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

CO2 capture from air and its conversion to CH4 using dual functional materials supported on high surface area graphite

  • Moral Pombo, Jorge
  • García-Bordejé, José Enrique
  • Liu, Yuefeng
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
15 figures, 1 table., Several cycles of CO2 capture from synthetic air containing 400 ppm of CO2 and subsequent conversion to CH4 have been performed using dual functional materials consisting of 4 wt% Ru and 10 wt% Ba or Cs supported on a high surface area graphite. The effect of the presence of humidity and the regeneration conditions have been assessed. The presence of moisture in the air enhances CO2 capture. The capture material is not properly regenerated in the absence of H2-containing atmosphere or at temperatures below 300 ºC. The exhaustive characterization by XRD, XPS, TEM and temperature programmed reduction and reaction allowed to shed some light about the reasons of the different behavior of Ba and Cs based dual functional materials. Cs is more efficiently utilized than Ba, providing higher CO2 capture capacities (0.44 mmol g−1) and CH4 productivity (0.41 mmol g−1). The outperformance of Cs is attributed to the more homogeneous and better dispersed species which are regenerated at lower temperatures., The Financial support from MICIU/AEI/10.13039/501100011033 and from FEDER, UE through project PID2023 146481OB-I00 and Gobierno de Aragón (Grupo Reconocido DGA T03_17R) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Supplementary information for CO2 capture from air and its conversion to CH4 using dual functional materials supported on high surface area graphite [Dataset]

  • Moral Pombo, Jorge
  • García-Bordejé, José Enrique
  • Liu, Yuefeng
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
Under a Creative Commons BY-NC 4.0 license., Figure S1. Blank experiment with the bare HSGA support. Figure S2. Evolution of gases during CO2 capture stage from dry air for several cycles using RuBa(1:1)/HSAG. Figure S3. Evolution of gases during regeneration after CO2 capture from dry air for several cycles using RuBa(1:1)/HSAG. Figure S4. Electron microscopy characterization of the RuCs 1:2 sample used in reaction. Figure S5. Electron microscopy characterization of the RuBa 1:1 sample used in reaction., The Financial support from MICIU/AEI/10.13039/501100011033 and from FEDER, UE through project PID2023 146481OB-I00 and Gobierno de Aragón (Grupo Reconocido DGA T03_17R) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Supporting information for Effect of Cs and Ba promoters on Ni/graphite catalysts for CO2 conversion via the reverse water gas shift reaction [Dataset]

  • Moral Pombo, Jorge
  • Conesa, José María
  • Campos Castellanos, Eduardo
  • García-Bordejé, José Enrique
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
Under a Creative Commons license BY-NC 3.0., Figure S1: XPS spectrum of Ni 2p3/2 region for Ni catalyst. Figure S2: Deactivation of Ni-Cs (1:1) and Ni-Ba (2:1) catalysts as a function time on stream., This work was funded by MICIU/AEI/https://doi.org/10.13039/501100011033 and by FEDER, UE through grant PID2023-146481OB-I00 and by Gobierno de Aragón (Grupo Reconocido DGA T03_17R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Butanol Production by Ethanol Condensation: Improvements and Limitations in the Rational Design of Cu-Ni-MgO/Graphite Catalysts

  • Rodríguez-Ramos, Inmaculada
  • López-Olmos, Cristina
  • Guerrero-Ruiz, Antonio
The advancement in catalytic processes utilizing sustainable raw materials, such as bioethanol, represents a key scientific challenge in this century. One potential approach to producing 1-butanol, a compound primarily obtained from petroleum-derived sources, is through the Guerbet reaction. For this transformation, various multifunctional catalysts have been explored, some of which incorporate Cu and/or Ni nanoparticles that facilitate hydrogenation and dehydrogenation reactions, along with magnesium oxide, which provides the necessary acid/base functionality. To promote nanoparticle formation and maximize the exposed active surface area, high-surface-area graphite (HSAG), a hydrophobic and inert support material, emerges as a promising candidate. In this study, different catalyst formulations containing these components were tested under moderate reaction conditions, at temperatures between 440 and 580 K and a pressure of 50 bar. A strong correlation was observed between butanol selectivity and the presence of medium–high strength basic sites, complemented by moderate acidity. Furthermore, optimizing the copper and nickel loadings to 4 wt.% Cu and 1 wt.% Ni significantly minimized the formation of unwanted byproducts. The highest butanol selectivity (44%) was achieved using a 4Cu1Ni-Mg/HSAG catalyst, which had been pretreated in helium at 723 K before H<sub>2</sub> reduction, yielding approximately 9% 1-butanol., This study was funded by MICIU/AEI/10.13039/501100011033 and by FEDER, UE, through grant PID2023-146481OB-I00., C.L.-O. thanks the MECD of Spain for a FPU predoctoral grant FPU16/05131., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bifunctional Na–Ru on gamma-alumina for CO2 capture from air and conversion to CH4: impact of the regeneration method and support on monolithic contactors

  • García-Bordejé, José Enrique
  • Conesa, José María
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
9 figures, 1 table.-- Supplementary information available., Dual functional materials (DFMs) have the potential to improve the process of CO2 capture and subsequent conversion to fuel. Materials consisting of Na and Ru supported on alumina have been investigated for cyclic direct CO2 air capture and conversion to CH4. We have studied the regeneration conditions, specifically the target temperature and gas composition (inert or hydrogen-containing gas) during heating. The effect of air humidity and Na loading on the effectiveness of CO2 capture has also been assessed. Finally, the DFMs have been successfully implemented as structured contactors with a low pressure drop, which is an unavoidable requirement for practical application., The financial support from MICIU/AEI/10.13039/501100011033 and by FEDER, UE through grant PID2023-146481OB-I00, Gobierno de Aragón (Grupo Reconocido DGA T03_17R), and associated EU Regional Development Funds is gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Carbon-supported non-noble metal catalysts for efficient synthesis of the biofuel 2,5-dimethylfurfural from 5‑hydroxymethylfurfural in 1-butanol under mild conditions

  • Morales, M. V.
  • Conesa, J. M.
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
2,5-Dimethylfuran (DMF), which is one of the most promising liquid biofuels, has garnered significant attention due to its potential to develop the utilization of biomass energy. In this work, its synthesis through the hydrodeoxygenation reaction (HDO) of 5-hydroxymethylfurfural (HMF) has been studied on Ni catalysts supported on various metal oxides and a high surface graphite (HSAG), in a batch reactor, using 1-butanol as a solvent. At 180 °C and under 30 bar H2, the catalytic activity and the predominant reaction route were found to be strongly conditioned by the nature of the support, as well as by the presence of impurities depending on the commercial HMF feedstock employed. The HSAG support turned out to be the most suitable for the HDO of HMF leading to the formation of DMF, via rupture of the C-O bonds. Additionally, the catalytic performance of Co and Cu supported on this graphitic material was studied, being Cu the one that offers the best yields to DMF (95 %), even in the absence of external hydrogen (84 %), confirming that butanol acts as a hydrogen donor in addition of solvent., This work was supported by the project PID2023–146481OB-I00 funded by the MICIU/AEI/10.13039/501100011033 and FEDER/UE. M.V. Morales gratefully acknowledges the funding received through the “Ramón y Cajal 2022” (RYC2022–036981-I) and “Investigadores tempranos UNED-Santander 2023” projects., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Dual functional material based on Ru-alkali metals on alumina for the direct CO2 capture from air and subsequent conversion to CH4

  • García-Bordejé, José Enrique
  • Conesa, José María
  • Guerrero Ruíz, A.R.
  • Rodríguez-Ramos, Inmaculada
Oral communication presented at the ISGC 2025, the world event in sustainable chemistry research & innovation, La Rochelle (France), 12th-16th May 2025., [Introduction] Dual functional materials (DFM) for CO2 capture and conversion combine both processes in one single material and reactor intensifying the process with enhanced mass transport and energy efficiency and avoiding cost of CO2 capture and transport of conventional carbon capture and utilization (CCU) approaches. These materials have been applied to CO2 capture from flue gases at high temperature [1-3]. Recently, CO2 capture directly from air (DAC) is gaining impetus since it has been proposed as one of the technologies leading to negative CO2 emissions [4]. The use of DFM for DAC is very scarce [5] due to the challenging high CO2 dilution and atmospheric temperature and pressure. Herein, bimetallic materials consisting on Ru nanoparticles (3 wt%) and K or Na metals (with different molar ratios) supported on mesoporous alumina have been prepared. The materials have been tested in the capture of CO2 from air at 40 ºC and subsequent conversion to CH4 heating at several temperatures (200ºC-300 ºC) under H2 flow. We have studied the effect of several parameters in the cyclic performance during CO2 capture and conversion such as the effect of the alkaline metal loading, the temperature of the regeneration and the presence of humidity in the air. [Experimental] Bimetallic Ru-Na and Ru-K dual functional materials (DFM) with different ratios have been supported on mesoporous alumina keeping a constant Ru loading of 3 wt% on the DFM. To this end, alkali metal and Ru where impregnated by incipient wetness impregnation and calcination at 500 ºC in Ar and subsequent reduction in H2 at 500 ºC after metal deposition. The DFMs were characterised by TEM, N2 physisorption, XRD, TPR and XPS. Bimetallic Ru-Na and Ru-K dual functional materials (DFM) with different ratios have been supported on mesoporous alumina keeping a constant Ru loading of 3 wt% on the DFM. To this end, alkali metal and Ru where impregnated by incipient wetness impregnation and calcination at 500 ºC in Ar and subsequent reduction in H2 at 500 ºC after metal deposition. The DFMs were characterised by TEM, N2 physisorption, XRD, TPR and XPS. [Results] The amount of CO2 captured from air was calculated by integration of the CO2 breakthrough curve (Figure 1a). Figure 1b shows the gases released in the regeneration heating under 20% H2 flow up to different temperatures. A CO2 peak (discontinuous line) and a CH4 peak (continuous line) are observed. Unconverted CO2 adsorbed in weak basic sites is evolved at the lower temperature range. From 130 ºC on a peak of CH4 evolves. At a regeneration temperature of 200 ºC the maximum is not reached but at 250 ºC the maximum is reached. Therefore, this temperature is considered enough to regenerate the capture sites for a next cycle. The amount of captured CO2 increases with the alkali metal loading up to a ratio (1:10) both for Ru-Na and Ru-K series while for higher alkali loading of (1:14.6) the captured CO2 decreases (Figure 2). The maximum CO2 captured are ~500 µmol g-1 and 400 µmol g-1 for Ru-Na (1:10) and Ru-K (1:10), respectively. In the case of Ru-Na DFM the CO2 production decreases to negligible values for the higher loadings, namely (1:10) and (1:14.6) suggesting that the sites of weakly adsorption of CO2 disappear. In contrast, for the Ru-K series the selectivity to CH4 decreases as the alkali loadings increases. Higher CO2 selectivities decreases CH4 production and increases the subsequent costs of separation. The DFMs show a remarkable CO2 capture capacity, which increases in humid conditions, being competitive and even surpassing other capture materials used in DAC in the literature. In addition, the high selectivity to methane intensifies the process compared to other CCU approaches., The Financial support from Spanish “Agencia Estatal de Investigación” (AEI, project PID2023-146481OB-I00), Gobierno de Aragón (Grupo Reconocido DGA T03_17R) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Captura de CO2 directa del aire y su conversión en CH4 usando materiales de doble función

  • García-Bordejé, José Enrique
  • Conesa, José María
  • Rodríguez-Ramos, Inmaculada
  • Guerrero Ruíz, A.R.
Resumen del póster presentado en el Congreso de la Sociedad Española de Catálisis (SECAT) en Alcalá de Henares (España), 17-20 de Junio de 2025., Los materiales de doble función (DFM) para la captura y conversión de CO2 combinan ambos procesos usando un sólo material y reactor. De manera que se intensifica el proceso con una transferencia de masa y calor mejoradas. Además, se evitan los costos de presurización y transporte de CO2 generados en los procesos convencionales de captura y utilización (CCU). DFMs se han usado ampliamente para la captura del CO2 de gases de chimenea a altas temperaturas (300-500 ºC) [1-3]. Más recientemente, la captura de CO2 directa del aire (DAC) está ganando interés debido a que se ha propuesto como una tecnología que conduce a emisiones negativas de CO2 [4]. Sin embargo, se han aplicado raramente para DAC [5] debido principalmente a la gran dilución del CO2 y a los altos costos de regeneración. En este trabajo, hemos preparado DFMs basados en un metal alcalino (K o Na) y Ru soportados tanto en alúmina como en grafito de alta superficie. Dichos DFMs se han caracterizado y se ha estudiado la influencia del porcentaje de alcalino y la temperatura de regeneración en ciclos de captura y metanación., The Financial support from MICIU/AEI/10.13039/501100011033 and from FEDER, UE through project PID2023-146481OB-I00 and Gobierno de Aragón (Grupo Reconocido DGA T03_17R) are gratefully acknowledged, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Contribución de congreso (ConferenceOutput)

Bifunctional materials for integrated DAC and conversion to methane

  • García-Bordejé, José Enrique
  • Moral Pombo, Jorge
  • Conesa, José María
  • Guerrero Ruíz, A.R.
  • Rodríguez-Ramos, Inmaculada
Abstract of the oral communication presented at the 22nd International Conference on Carbon Dioxide Utilization, 22nd ICCDU, 23rd-27th June, Lisbon (Portugal)., To fight against accelerating climate change and to comply the Paris agreement, neutral or even negative CO2 emissions measures must be urgently implemented such as CO2 capture from diluted sources followed by storage (CCS) or utilization (CCU) [1]. Integrating CO2 capture and conversion into one single process offers several advantages, including avoiding the need for CO2 pressurization and transport to storage or conversion site. The integration also enhances process intensification by improving mass and heat transfer while reducing equipment investment. The intensification is even greater if one single material is used for both capture and catalytic conversion, as the heat and mass transfer distances are nanometric. These materials, known as dual functional materials (DFMs), consist of a CO2 capture component (alkali metal) and a metal catalyst for subsequent methanation. DFMs were firstly introduced by Farrauto et al. [1] and have since then been widely used for capture of CO2 from flue gases at isothermal conditions as the temperature of the emitted gas matches that of methanation reaction [2,3]. DFMs were also proposed for direct air capture (DAC) and subsequent CO2 conversion [4]. However, this application presents several challenges, such as the high dilution of CO2 (400 ppm) and the large volumes of air that must be treated. In previous articles we studied DFMs for the capture of CO2 from flue gases [5,6]. Here we extend the application to DAC [7,8]. To this end, we prepared DFMs consisting of a methanation catalyst (4 wt%Ru) and an alkaline metal (Cs or Ba) to achieve (Cs or Ba)/Ru atomic ratios of 1 and 2, dispersed on a high surface area graphite. DFM were tested in DAC (40ºC) and subsequent methanation (300 ºC) for 25 cycles. At stable cyclic performance, the best performing DFM of each series, RuBa (1:1) and RuCs (1:2), captured 0.1 mmol g-1 and 0.44 mmol g-1, respectively. Based on the characterisation, we attributed this to the higher dispersion of Cs and to the higher stability of the carbonates formed with Ba which are not regenerated completely at 300 ºC., This work was funded by MICIU/AEI/10.13039/501100011033 and by FEDER, UE through grant PID2023-146481OB-I00, Gobierno de Aragón (Grupo Reconocido DGA T03_17R), and associated EU Regional Development Funds., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3-component (N, Fe, Co) atomically dispersed ORR catalysts prepared by laser-driven decomposition of organic precursors

  • Pakrieva, Ekaterina
  • Hernández-Ferrer, Javier
  • Martínez, Gema
  • Balas, Francisco
  • García-Bordejé, José Enrique
  • Ansón-Casaos, Alejandro
  • Simonelli, Laura
  • Bartolomé, Fernando
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Hueso, José L.
  • Santamaría, Jesús
Data will be made available on request., The sluggish kinetics of the oxygen reduction reaction (ORR) remain a key bottleneck for the commercialization of proton exchange membrane fuel cells (PEMFCs), driving the search for efficient, non-precious metal catalysts. Herein, we present a laser-assisted pyrolysis strategy for the synthesis of nitrogen-doped carbon (NC) materials, both metal-free and containing atomically dispersed Fe and Co, using aerosolized phthalocyanine precursors and a near-instantaneous rapid decomposition under a high-energy laser beam, while preventing metal aggregation. A single-step post-synthetic thermal activation under an NH₃/N₂ atmosphere further tailors the textural and surface properties, without requiring ammonia co-feeding during laser pyrolysis, acid etching, or multiple treatments, marking a significant improvement over our previously reported single atom (Fe-N/C) protocols. The resulting Fe_Co/NC_tr catalyst exhibits high specific surface area, enhanced microporosity, improved graphitization, and increased abundance of electrochemically beneficial nitrogen sites. Compared to our earlier reported Fe–N/C catalysts, Fe_Co/NC_tr delivers significantly higher limiting current densities and enhanced durability in alkaline media. Overall, the developed Fe_Co/NC catalyst exhibits good ORR catalytic activity and outstanding long-term stability in alkaline media, comparable to the state-of-the-art commercial Pt/C catalysts. Cyanide poisoning tests confirm the essential role of atomically dispersed Fe2+ and Co2+ as active ORR sites., The authors thank funding from the Spanish Research Agency and MICN/AEI (projects CNS2022-135911 (J.L.), PID2020-114926RB-I00 (J.S.), PID2022-139671OB-I00 (W.M. and A.B) and PID2023-146481OB-I00 (E.G.). Severo Ochoa funds (CEX2023-001286-S) are acknowledged by MICIU/AEI/10.13039/501100011033. Financial support from Diputación General de Aragón under project T57_23R (J.S.) and T03_23R (W.M., A.B., E.G., A.A.) (Grupos Reconocidos), Project “ERDF A way of making Europe” by the European Union is gratefully acknowledged. EP thanks Juan de la Cierva Formación postdoctoral fellowship (JDC2022-049007-I) financed by MICIU/AEI/10.13039/501100011033 and by the European Union “NextGenerationEU”/PRTR”., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001286-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Integrated CO2 capture from air with unprecedently efficient conversion to methane using Ru-alkali/alumina dual functional material by optimizing alkali loading

  • García-Bordejé, José Enrique
  • Conesa, José María
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
14 figures, 3 tables., Dual functional materials composed of a noble metal (Ru) and an alkali metal (Na or K) supported on mesoporous alumina have been prepared and applied for the two-stage cyclic process consisting of capturing CO2 directly from air and subsequent conversion to methane. The alkali loading was varied systematically while keeping a constant Ru content. Increase alkali loading significantly impacted on the CO2 capture, temperature of complete regeneration and efficiency for the conversion to CH4. The CO2 capture was maximized at a molar Ru:alkali ratio of 1:10, achieving CO₂ capture capacities of 480 µmol g⁻¹ for RuK and 740 µmol g⁻¹ for RuNa series. At this ratio, the Na-based material exhibited an unprecedented CH₄ conversion efficiency of 96 %. Structural characterization enabled the development of a structure–performance relationship model that explains the superior performance. These findings highlight the critical role of alkali loading optimization in enhancing the efficiency of integrated CO₂ capture and valorization into synthetic fuel., The financial support from MICIU/AEI/10.13039/501100011033 and from FEDER, UE through project PID2023 146481OB-I00 and Gobierno de Aragón (Grupo Reconocido DGA T03_23R) are gratefully acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Bottom-up assembly of cellulose nanocrystals as a green entry to structured functional carbons

  • Güemes, Lucas
  • Calvo Peña, Víctor
  • Maya Segura, Vanessa B.
  • Pires, Elísabet
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • García-Bordejé, José Enrique
  • González Domínguez, José Miguel
Data will be made available on request., The bottom-up assembly of cellulose nanocrystals (CNCs) into porous scaffolds offers a sustainable route to translate their intrinsic properties into functional 3D materials. This strategy enables precise control over porous architectures, unlocking opportunities for high-performance materials tailored to specific applications. Here, we present the fabrication of structured carbons derived from nanocellulose precursors. CNCs are isolated from cellulosic feedstock in type-I and type-II crystalline allomorphs via a one-pot synthesis process followed by minimal processing steps. The resulting aqueous CNC colloids self-assemble into cross-linked hydrogels through controlled hydrothermal aggregation, followed by lyophilization to produce macroporous aerogels (bulk porosities up to 98%). Each allomorph exhibits distinct aggregation behavior, explored for the first time with type-II CNCs. As proof of concept, these aerogels undergo pyrolysis at varying temperatures and subsequent sulfonation, yielding highly porous carbons functionalized with sulfonic acid groups (functionalization degree of ca. 2400 μmol·g−1). The resulting materials combine macroporosity from hydrothermal assembly with microporosity generated during pyrolysis and sulfonation, forming a hierarchical structure ideal for catalytic applications. Their performance is demonstrated in solketal synthesis (yielding ∼90% of solketal in consecutive cycles after 4 h at room temperature) positioning CNC-based sulfonated aerogels as a greener alternative to conventional Brønsted acid catalysts and surpassing classical activated carbons in sustainability and design., Financial support from the Spanish MCIN/AEI/10.13039/501100011033 and ‘‘ERDF A way of making Europe’’ by the European Union under project grants PID2022-139671OB-I00, PID2023-146481OB-I00 and PID2023-147116OB-I00, as well as from the Gobierno de Aragón (DGA), in the R&D&I projects in priority lines and of a multidisciplinary nature (project grant PROY_T41_24), and through the grants to research groups (Grupo Reconocido DGA-T03_23R) is acknowledged. L.G. thanks the DGA for funding his PhD contract (ref. CUS/702/2022)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Selective Acetylene Hydrogenation: Influence of Carbon Supports on the Stabilization of Pd4S-like Active Sites

  • Campos-Castellanos, Eduardo
  • Rodríguez-Ramos, Inmaculada
  • Bañares, Miguel A.
  • Guerrero-Ruiz, Antonio
  • Morales, María V.
This article belongs to the Section Energy and Catalysis, This study examines how both the nature of the carbon support and the palladium precursor influence catalytic performance in acetylene hydrogenation. Six Pd-based catalysts were prepared on four carbon materials—high-heat-treated fibers (HHTs), carbon nanotubes, activated carbon and high surface area graphite—using either sulfate or chloride precursors. Catalytic tests performed in a continuous fixed-bed reactor reveal that HHT-supported catalysts achieve the highest ethylene selectivity and long-term stability, while in general catalysts derived from sulfate precursors exhibit enhanced selectivity compared to their chloride-derived counterparts. These improvements are consistent with the formation of sulfur, which may be incorporated as sub-stoichiometric sulfide species (S2−) interacting with metallic Pd, as revealed by the XPS results, rather than to palladium dispersion alone. The role of the carbon support in stabilizing these sites was further assessed by complementary characterization techniques, including transmission electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy and Raman spectroscopy. The combined results indicate that highly graphitic supports such as HHT fibers favor sulfur retention at the catalyst surface, thereby promoting the stability and catalytic performance of Pd–S active motifs during acetylene hydrogenation., This study was funded by MICIU/AEI/10.13039/501100011033 and by FEDER, UE through grant PID2023-146481OB-I00. E.C.C acknowledges the grant from the FPI-UNED program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Appendix A. Supplementary material for Integrated CO2 capture from air with unprecedently efficient conversion to methane using Ru-alkali/alumina dual functional material by optimizing alkali loading [dataset]

  • García-Bordejé, José Enrique
  • Conesa, José María
  • Guerrero-Ruiz, Antonio
  • Rodríguez-Ramos, Inmaculada
Under a Creative Commons BY-NC 4.0 license., Figure S1. Evolution of the main gases in the CO2 capture from wet synthetic air using DMF (a) RuK(1:7.4) and (b) RuNa (1:7.4).-- Figure S2. (a) CH4 and CO2 evolved during regeneration of DFM RuK (1:14.6) at different temperatures and times. (b) cumulative CH4 production.-- Figure S3. N2 adsorption isotherm (a,c) and pore size distribution (b,d) measured by the BJH method applied to the desorption branch for RuK (a,b) series and RuNa series (c, d).-- Figure S4. Fitting of XPS core level spectra of Ru 3p3/2 for DFM or RuK (a) and RuNa (b) DFMs with different alkali loadings.-- Figure S5. Core level XPS spectra of K 2p/ C 1s/Ru 3d (a) and Na 1s (b) for RuK and RuNa DFMs, respectively, with different alkali loadings.-- Table S2. Parameters after quantification of the XPS fitting, The financial support from MICIU/AEI/10.13039/501100011033 and from FEDER, UE through project PID2023 146481OB-I00 and Gobierno de Aragón (Grupo Reconocido DGA T03_23R) are gratefully acknowledged., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

3-component (N, Fe, Co) atomically dispersed ORR catalysts prepared by laser-driven decomposition of organic precursors

  • Pakrieva, Ekaterina
  • Hernandez-Ferrer, Javier
  • Martinez, Gema
  • Balas, Francisco
  • García-Bordeje, Enrique
  • Anson-Casaos, Alejandro
  • Simonelli, Laura
  • Bartolome, Fernando
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Hueso, Jose L.
  • Santamaria, Jesus
The sluggish kinetics of the oxygen reduction reaction (ORR) remain a key bottleneck for the commercialization of proton exchange membrane fuel cells (PEMFCs), driving the search for efficient, non-precious metal catalysts. Herein, we present a laser-assisted pyrolysis strategy for the synthesis of nitrogen-doped carbon (NC) materials, both metal-free and containing atomically dispersed Fe and Co, using aerosolized phthalocyanine precursors and a near-instantaneous rapid decomposition under a high-energy laser beam, while preventing metal aggregation. A single-step post-synthetic thermal activation under an NH₃/N₂ atmosphere further tailors the textural and surface properties, without requiring ammonia co-feeding during laser pyrolysis, acid etching, or multiple treatments, marking a significant improvement over our previously reported single atom (Fe-N/C) protocols. The resulting Fe_Co/NC_tr catalyst exhibits high specific surface area, enhanced microporosity, improved graphitization, and increased abundance of electrochemically beneficial nitrogen sites. Compared to our earlier reported Fe–N/C catalysts, Fe_Co/NC_tr delivers significantly higher limiting current densities and enhanced durability in alkaline media. Overall, the developed Fe_Co/NC catalyst exhibits good ORR catalytic activity and outstanding long-term stability in alkaline media, comparable to the state-of-the-art commercial Pt/C catalysts. Cyanide poisoning tests confirm the essential role of atomically dispersed Fe2+ and Co2+ as active ORR sites.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Tuning 2e− and 4e− oxygen reduction pathways in laser-driven FeC electrocatalysts for H2O2 production and Zn–air batteries

  • Pakrieva, Ekaterina
  • Hernández-Ferrer, Javier
  • Rueda-Flores, Ana
  • Balas, Francisco
  • García-Bordeje, Enrique
  • Ansón-Casaos, Alejandro
  • Usoltsev, Oleg
  • Benito, Ana M.
  • Maser, Wolfgang K.
  • Hueso, Jose L.
Electrocatalytic oxygen reduction plays a central role in electrochemical energy technologies and in the production of hydrogen peroxide. Achieving selective control over the two-electron (2e−) and four-electron (4e−) oxygen reduction reaction (ORR) pathways within a single catalyst platform remains challenging. Here, we report a laser-driven synthesis of Fesingle bondC nanostructures that enables tunable ORR selectivity through controlled post-treatment. Air annealing at 300 °C yields high H2O2 selectivity (~75% at 0.65 V vs RHE), attributed to oxygen-rich groups and well-developed mesoporosity. Notably, with an optimized 2-electron catalyst, 80 ppm of H2O2 with 94% faradaic efficiency was achieved after 24 h of electrolysis. In contrast, an ammonia based (NH3/N2) treatment at 900 °C promotes the formation of a microporous structure and the incorporation of nitrogen species, resulting in selective water production (~86% at 0.65 V vs RHE). The 4-electron catalyst delivers power and stability comparable to Pt/GC in a primary zinc–air battery. These findings demonstrate a practical approach for tuning ORR selectivity within a Fe-containing carbon-based platform, using scalable processing and trace Fe contents (<0.1 wt%) with Fe present as atomically dispersed sites, limiting leaching and Fenton-type reactions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Bottom-up assembly of cellulose nanocrystals as a green entry to structured functional carbons

  • Güemes, Lucas
  • Calvo, Víctor
  • Maya-Segura, Vanessa B.
  • Pires, Elísabet
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • García-Bordejé, Enrique
  • González-Domínguez, José M.
The bottom-up assembly of cellulose nanocrystals (CNCs) into porous scaffolds offers a sustainable route to translate their intrinsic properties into functional 3D materials. This strategy enables precise control over porous architectures, unlocking opportunities for high-performance materials tailored to specific applications. Here, we present the fabrication of structured carbons derived from nanocellulose precursors. CNCs are isolated from cellulosic feedstock in type-I and type-II crystalline allomorphs via a one-pot synthesis process followed by minimal processing steps. The resulting aqueous CNC colloids self-assemble into cross-linked hydrogels through controlled hydrothermal aggregation, followed by lyophilization to produce macroporous aerogels (bulk porosities up to 98%). Each allomorph exhibits distinct aggregation behavior, explored for the first time with type-II CNCs. As proof of concept, these aerogels undergo pyrolysis at varying temperatures and subsequent sulfonation, yielding highly porous carbons functionalized with sulfonic acid groups (functionalization degree of ca. 2400 μmol·g−1). The resulting materials combine macroporosity from hydrothermal assembly with microporosity generated during pyrolysis and sulfonation, forming a hierarchical structure ideal for catalytic applications. Their performance is demonstrated in solketal synthesis (yielding ∼90% of solketal in consecutive cycles after 4 h at room temperature) positioning CNC-based sulfonated aerogels as a greener alternative to conventional Brønsted acid catalysts and surpassing classical activated carbons in sustainability and design.