Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Novel Egg White Protein–Chitin Nanocrystal Biocomposite Films with Enhanced Functional Properties

  • Baquero-Aznar, Víctor
  • Calvo, Víctor
  • González-Domínguez, José Miguel
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • Salvador, María Luisa
  • González-Buesa, Jaime
This study aims to develop egg white protein (EWP) biocomposite films reinforced with chitin nanocrystals (ChNCs, 1–5 wt.%) by compression molding to overcome the mechanical and barrier limitations of protein-based films for sustainable packaging. ChNC incorporation may modulate film microstructure, crystallinity, and thermal stability, thereby enhancing functional performance. Films were prepared by adding ChNCs either as aqueous suspensions or lyophilized powder, and their structural, thermal, mechanical, optical, and barrier properties were systematically evaluated. Scanning electron microscopy confirmed a more homogeneous dispersion of ChNCs when added as suspensions, while powder addition promoted partial aggregation. X-ray diffraction revealed increased crystallinity with ChNC reinforcement. Mechanical tests showed that films with 2 wt.% ChNCs in suspension exhibited the highest tensile strength, whereas those with 5 wt.% in powder form became stiffer but less extensible. Oxygen permeability was not significantly affected, while water vapor permeability decreased by up to 14.5% at 2 wt.% ChNCs incorporated as powder. Transparency and color remained largely unchanged by ChNC addition, except for a slight increase in yellowness. Overall, these findings demonstrate that the incorporation method and concentration of ChNCs play a crucial role in tailoring the physicochemical performance of EWP films. The results provide new insights into the design of EWP-based nanocomposites and support their potential as bio-derived materials for advanced food packaging applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Carbon nanotube film electrodes enabled by nanostructured biopolymers through aqueous processing

  • Martínez-Barón, Carlos
  • Calvo, Víctor
  • Álvarez-Sánchez, Miguel Ángel
  • Pascual, F. Javier
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • Ansón-Casaos, Alejandro
  • González-Domínguez, José Miguel
Processing carbon nanotubes (CNTs) into conductive films via liquid-phase is highly attractive for the fabrication of electronic and electrochemical device components. However, conventional deposition methods usually suffer from several limitations, including environmental concerns, loss of intrinsic properties, and poor reproducibility. Nanostructured biopolymers (NBs), such as cellulose (CNCs) and chitin (ChNCs) nanocrystals, offer an environmentally friendly strategy for dispersing CNTs in water alternative to organic solvents, surfactants or chemical functionalization. In this work, we present the first direct comparison of conductive and electroactive films resulting from using CNCs and ChNCs as dispersing agents for both single-walled and multi-walled CNTs. The as-made aqueous dispersions are used as inks to fabricate CNT/NB films via spray coating, achieving excellent homogeneity, controllable film thickness, and sheet resistances mostly below 130 Ohm Sq-1. Furthermore, we demonstrate that postdeposition thermal treatment at 450 1C in an inert atmosphere effectively pyrolyzes the non-conductive NB matrix while increasing contacts between CNTs in the network, leading to enhanced electrical conductivities and lectrochemically active surface areas. These findings highlight NBs as greener processing agents for the formulation of waterborne CNT inks and emphasize their relevance for the controlled and sustainable fabrication of conductive films and electrodes.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Bottom-up assembly of cellulose nanocrystals as a green entry to structured functional carbons

  • Güemes, Lucas
  • Calvo, Víctor
  • Maya-Segura, Vanessa B.
  • Pires, Elísabet
  • Maser, Wolfgang K.
  • Benito, Ana M.
  • García-Bordejé, Enrique
  • González-Domínguez, José M.
The bottom-up assembly of cellulose nanocrystals (CNCs) into porous scaffolds offers a sustainable route to translate their intrinsic properties into functional 3D materials. This strategy enables precise control over porous architectures, unlocking opportunities for high-performance materials tailored to specific applications. Here, we present the fabrication of structured carbons derived from nanocellulose precursors. CNCs are isolated from cellulosic feedstock in type-I and type-II crystalline allomorphs via a one-pot synthesis process followed by minimal processing steps. The resulting aqueous CNC colloids self-assemble into cross-linked hydrogels through controlled hydrothermal aggregation, followed by lyophilization to produce macroporous aerogels (bulk porosities up to 98%). Each allomorph exhibits distinct aggregation behavior, explored for the first time with type-II CNCs. As proof of concept, these aerogels undergo pyrolysis at varying temperatures and subsequent sulfonation, yielding highly porous carbons functionalized with sulfonic acid groups (functionalization degree of ca. 2400 μmol·g−1). The resulting materials combine macroporosity from hydrothermal assembly with microporosity generated during pyrolysis and sulfonation, forming a hierarchical structure ideal for catalytic applications. Their performance is demonstrated in solketal synthesis (yielding ∼90% of solketal in consecutive cycles after 4 h at room temperature) positioning CNC-based sulfonated aerogels as a greener alternative to conventional Brønsted acid catalysts and surpassing classical activated carbons in sustainability and design.