Pasar al contenido principal

ESTRATEGIAS INNOVADORAS PARA ALCANZAR SISTEMAS DE POLIGENERACION INTELIGENTES Y SOSTENIBLES: UN ENFOQUE EN EL ANALISIS DE CICLO DE VIDA Y MODELOS DE CONTROL PREDICTIVO.

PID2023-148958OB-C21

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para Impulsar la Investigación Científico-Técnica y su Transferencia
Subprograma Subprograma Estatal de Generación de Conocimiento
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2023
Plan Estatal 2021-2023 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Rheological study on xylitol crystallization for its use as phase change material: analytical and statistical analysis

  • Navarro, Miguel
  • Gracia, Zeus
  • Asín, Jesús
  • Lázaro, Ana
  • Martí, Marta
  • Delgado, Mónica
In a global context in which decarbonization of society is wanted through the use of renewable sources, energy storage plays a fundamental role. Among the different forms of energy storage that exists, this work focuses on latent heat energy storage (LHTES) for medium-low temperatures, between 70 °C and 120 °C. Xylitol, a sugar-alcohol, is a promising phase change material (PCM) due to its low cost, low corrosivity, high latent heat (240 J/g) and a melting temperature of 92 °C. However, its use as PCM is hindered by a high degree of supercooling and a low crystallization rate. To address these challenges, this work used a seeding and shearing technique to trigger crystallization. Rheological experiments were performed to monitor viscosity changes during crystallization, in order to study the crystallization induction time. The systematic analysis included the effects of temperature (70–90 °C), shear rate(1-100s−1), and seed crystal size (300–400 μm and 600–700 μm). Key results show that temperature is the most dominant factor. The shortest induction time at 70 °C was found at 10s, increasing to 1500s at 90 °C. Increasing seed size and reducing the rheometer gap also shortened induction times, while shear rate had minimal influence, likely due to non-uniform shear during the test. For practical applications, operating at 80 °C is recommended to balance induction time and energy loss due to supercooling. Optimizing shear-triggered mechanism, such as stirred tanks designs, can improve crystallization controllability.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Relative contribution and sensitivity analyses for decision-making in the environmental assessment of bio-based phase change materials

  • Da Silva Santos, Humberto
  • Guillen-Lambea, Silvia
This paper aims to investigate the environmental impact of the production of bio-based phase change materials to contribute to the advancement and development of energy systems with a low environmental impact. It uses relative contribution, local, and global sensitivity analysis to target critical inputs for decision-making. The materials selected are jojoba oil, coconut oil, lauric, myristic, and stearic acids, xylitol, and adipic acid, with melting temperatures varying from 14 °C to 152 °C. The methodology follows the ISO guidelines for the life cycle assessment of all materials, for which the boundary system has considered three unit processes: farming, transportation, and manufacturing. It was found that to produce 1 kg of adipic acid, the global warming potential is 13 kg CO2 eq, while for jojoba oil, it is only 0.96 kg CO2 eq. For phase change materials like jojoba oil, coconut oil, myristic acid, and stearic acid, farming dominates the global warming potential, while manufacturing takes over the major share of this environmental indicator for the remaining materials. The local sensitivity analysis results show that jojoba oil's global warming potential can increase by nearly 38 % if irrigation water reaches its upper bound. On the other hand, global sensitivity analysis shows the Sobol index by which inputs contribute to output uncertainty. For instance, the jojoba oil global warming uncertainty could be affected by 60 % by irrigation water. Results show that the higher melting temperature phase change materials have a higher footprint than the lower melting temperature ones, except for coconut oil, as a consequence of more process inputs and production process complexity. Overall, relative contribution analysis helps locate critical unit processes and inputs, while local sensitivity analysis allows for identifying how critical input variation affects the targeted indicator, and the global sensitivity analysis is useful to understand the critical inputs in terms of uncertainty.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Optimal operation and marginal costs in a complex polygeneration system including thermal energy storage and DHCN pipelines

  • De Souza, Ronelly José
  • Serra, Luis M.
  • Lozano, Miguel A.
  • Reini, Mauro
This paper proposes a thermoeconomic analysis to determine the hourly marginal costs of the optimal operation of a complex polygeneration system when the energy demand for a specific energy service increases at any time step, without modifying the operation mode of the system. The work analyses a case study which considers a mixed integer linear programming (MILP) model of an energy community (EC), comprising nine tertiary sector buildings and a central unit supplied by natural gas, solar energy, and electricity. The buildings exchange electricity through a local electric grid as well as heating and cooling through a district heating and cooling network (DHCN). The paper focuses on the marginal cost (MC) analysis of the electricity and heating demands regarding two of the EC buildings by evaluating representative time steps of a typical winter day. Additionally, a detailed analysis of the cost formation process for polygeneration heat production is conducted, clarifying the influence of thermal energy storage (TES) and DHCN on the marginal cost of heat production. The proposed marginal cost analysis reveals strategies for managing increased heat or electricity demands with minimal impact on the objective function. While the applied methodology offers robustness and transparency, it should be noted that the model under analysis does not include dynamic inefficiencies such as start-up/shut-down of technologies, and renewable variability is represented through deterministic time series. Thus, the mentioned optimal operation refers to the most cost-effective response to marginal demand changes within fixed operational modes. Obtained results indicate that optimal marginal paths have the potential to reduce operation costs by 26% compared to non-optimal ones.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Polysaccharide–protein complex-stabilized Pickering phase change material emulsions for low-temperature thermal energy storage

  • Yu, Tingting
  • Qiu, Xiaolin
  • Delgado, Mónica
  • Lázaro, Ana
  • Hu, Yang
Low-temperature phase change material emulsions (PCMEs) are excellent thermal storage media but have environmental and toxicity issues due to poorly degradable synthetic surfactants; single-component biopolymer systems lack stability, low-temperature Pickering emulsion research is scarce, protein-polysaccharide composite stabilizers in PCMEs are unreported, and Boron Nitride (BN) -biopolymer synergistic effects on supercooling remain unexplored. This study aims to develop an environmentally friendly, high-performance, low-temperature Pickering phase change material emulsion to simultaneously optimize stability, environmental compatibility, and thermal performance. This study proposes substituting traditional emulsifiers with self-assembled sodium caseinate (SC)-xanthan gum (XG) nanocomposites. Phase change emulsions were prepared by high-speed homogenization, and boron nitride was added to synergistically reduce supercooling and improve heat transfer. The SC–XG complexes adsorb at n-tetradecane/water interfaces, forming a viscoelastic interfacial network that enhances droplet stability and restricts coalescence. Thermal analysis revealed that, at 0.5% (w/v) XG, the 50 vol% n-tetradecane PCME droplets are uniform and kinetically stable, delivering a latent heat of 89.5 J g− 1. Adding only 0.75 wt% BN induces heterogeneous nucleation, cuts supercooling from 7.8 ◦C to 0.24 ◦C, and boosts thermal conductivity. This study proposes a novel protein-polysaccharide-based technical pathway for constructing green and sustainable low-temperature thermal storage materials, while also synergistically regulating the crystallization behavior and heat transfer performance of the emulsion through BN. This study provides both a theoretical foundation and a green technical solution for designing stable and efficient phase change material emulsions for thermal energy storage.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Integrated assessment of solid, liquid, and gaseous fuels derived from fixed-bed pyrolysis of waste tires

  • de Lima, Harryson Guimarães
  • Júnior, Clériston Moura Vieira
  • Santos, Humberto
  • Júnior, Adalberto Freire do Nascimento
  • Antonino, Antônio Celso Dantas
  • da Silva, Sérgio Peres Ramos
The improper disposal of end-of-life tires poses significant environmental challenges due to their petroleum-based composition and slow degradation, while simultaneously representing an underutilized energy resource. This study investigates the slow pyrolysis of shredded waste tires in a fixed-bed electrically heated reactor to evaluate the production and fuel properties of gaseous, liquid, and solid fractions. Experiments were conducted with 100 g samples under nitrogen at final temperatures of 400, 500, and 600 °C, with residence times of 40, 25, and 10 min, respectively. Higher temperatures promoted gas formation, increasing yields from 27% to 32% and achieving a maximum lower heating value of 30.54 MJ m−3 at 600 °C, with enhanced H2 and CH4 contents. Solid yields decreased slightly (41% to 37%), while char maintained stable heating values (~29 MJ kg−1). Liquid yields remained near 33% and showed high calorific values (~41 MJ kg−1), densities of 700–770 kg m−3, low acidity, low ash content, and increased viscosity at higher temperatures. Energy conversion efficiency reached 74.4% at 500 °C. The integrated evaluation of all fractions under identical conditions highlights fixed-bed pyrolysis as a promising pathway for waste-tire valorization and decentralized fuel production.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

An Experimental Investigation of the Emissions from a Generator Operating under Hydrogen, Diesel, and Biodiesel Co-Combustion

  • Peres, Sergio
  • Bezerra, Djailson Joaquim
  • Vieira Júnior, Clériston Moura
  • Da Silva Santos, Humberto
  • Souto Maior, Rafael Aguiar
  • González Rodríguez, Daniel
  • Antonino, Antonio Celso Dantas
  • de Miranda Loureiro, Eduardo César
Renewable fuels have gained significant attention due to the potential to replace their counterparts derived from fossil fuel. Among them, hydrogen and biodiesel have led the discussion. Thus, the objective of this study is to evaluate the use of hydrogen (H2) and biodiesel as partial or complete substitutes for gasoil (diesel fuel) in a compression ignition engine, focusing on performance and gaseous emissions. At full load, H2 supplied approximately 30% of the total fuel energy input. The experimental campaigns were conducted under four fuel configurations: diesel fuel only, diesel fuel + hydrogen, biodiesel only, and biodiesel + H2 in co-combustion. The results remarkably show that the combined use of biodiesel and hydrogen resulted in the elimination of greenhouse gas emissions. Compared with the diesel fuel operation mode, the biodiesel + H2 blend led to substantial reductions in CO, CO2, and NOx emissions. At full load, the measured emissions were as follows: diesel fuel − CO2: 7.66%, CO: 323 ppm, NOx: 639 ppm; diesel fuel + H2 − CO2: 5.95%, CO: 312 ppm, NOx: 829 ppm; biodiesel − CO2: 8.14%, CO: 266 ppm, NOx: 687 ppm; biodiesel + H2 − CO2: 4.67%, CO: 205 ppm, NOx: 597 ppm, showing that biodiesel reduces significantly the amount of emissions compared to diesel fuel or diesel fuel hydrogen blend. These findings highlight the potential of H2 − BD co-combustion as a cleaner alternative to conventional diesel, with significant benefits for greenhouse gas mitigation and air quality improvement.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Evaluation of thermal energy storage for medium-low temperature applications: Comparison of commercial solutions with a xylitol-based prototype

  • Navarro, Miguel
  • Lázaro, Ana
  • Delgado, Mónica
In recent years, thermal energy storage (TES) has become a promising and popular technology for energy storage. Among the different technologies, this work focuses on latent heat thermal energy storage (LHTES) system, specifically it assesses the potential of xylitol as phase change material (PCM) in TES systems for low-medium temperature applications. Xylitol, a sugar alcohol with stable supercooling, has a high latent heat (240 J/g), high energy storage density (1.45 kg/l), and a melting temperature of 92 °C. However, stable supercooling and low crystallization rate limits its practical application. Therefore, a laboratory-scale prototype working in the 70-100 °C range has been proposed and experimentally characterised that uses a seeding and shearing technique to mitigate this supercooling and accelerate crystallization, thereby increasing the thermal energy discharge power. The study compares this lab-scale prototype with four leading commercial solutions in terms of both materials and systems. Moreover, the methodology developed in the framework of IEA SHC Task 58 for TES system comparison in terms of energy density and power is applied. The results show the xylitol prototype has higher normalized power values than other experimental systems analysed in the framework of IEA SHC Task 58, reaching energy densities of up to 40.8 kWh/m3 system-wise in an optimized configuration. The study concludes that stirred TES prototype with xylitol is a competitive alternative to current commercial solutions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Sustainable Peg‐Based Shape‐Stabilized Phase Change Materials Using Raw Pine Cone as a Low‐Cost Filler and Graphite for Enhanced Thermal Conductivity

  • Akrouti, Amira
  • Trigui, Abdelwaheb
  • Delgado, Mónica
  • Navarro, Miguel
  • Lazaro, Ana
  • Hassani, Rym
This study investigates the development of a novel shape‐stabilized phase change material (ssPCM). Pinecone (PC) powder, a low‐cost and sustainable lignocellulosic support, was combined with polyethylene glycol (PEG 6000) as the phase change material (PCM). Graphite was incorporated to enhance thermal conductivity, minimize leakage, and improve shape stability. Thermophysical properties were evaluated to assess the potential of these ssPCM as thermal energy storage (TES) materials. The Fourier transform infrared spectroscopy (FTIR) was used to verify the chemical compatibility among components, and thermogravimetric analysis (TGA/DTG) to evaluate thermal stability and decomposition behavior. Brunauer–Emmett–Teller (BET) surface area, mercury intrusion porosimetry (MIP), and field emission scanning electron microscopy (FESEM) were conducted to investigate the structure of the PC support and its influence on ssPCMs. Density was measured using a thermomechanical analyzer (TMA), while thermal diffusivity was determined with a laser flash apparatus (LFA). Among the prepared composites, 80% PEG, 10% G, 10% PC showed the most promising thermal storage performance, with a latent heat of 153.7 kJ/kg by differential scanning calorimetry (DSC) and 207.3 kJ/kg by the T‐history method. Preliminary results suggest that these ssPCM offer a cost‐effective and reliable solution for TES applications, combining eco‐friendly materials with enhanced thermal, structural, and thermophysical performance.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

The Role of Thermal Energy Storage in Enhancing the Robustness of Solar-Thermal-Driven Polygeneration Systems for a Dairy Industry

  • Pina, Eduardo A.
  • Lázaro, Ana
  • Serra, Luis M.
  • Arif, M. Naveed
  • Guillén-Lambea, Silvia
  • Lozano, Miguel A.
Solar thermal-driven polygeneration (STDP) systems represent a promising approach to the production of clean and efficient energy for agri-food industries, with a wide range of temperatures for heating, cooling and power applications. This study conducted a technical, economic, and environmental assessment with particular focus on the role of three different thermal energy storage (TES) systems on the performance of STDP systems consisting of parabolic trough solar collectors, cogeneration Organic Rankine Cycle, auxiliary boiler, and mechanical chiller, to supply heating, cooling, and electricity services to a dairy industry located in Tauste, Spain. The analysis was carried out using a mixed-integer linear programming model that optimizes the selection and sizing of the equipment, as well as its operational performance over a full typical year. In order to evaluate the performance of the proposed system, 833 distinct optimisation cases were solved to study: (i) the role of TES systems located at different points (and corresponding temperature levels) within the plant layout; (ii) the interaction of the proposed system with the power grid; and (iii) sensitivity and robustness analyses based on variations in energy prices. The results showed that the proposed system achieved an annual solar fraction of 37.2%, with slightly lower costs (about 5%) and lower greenhouse gas emissions (about 37%) compared to the conventional supply system. In addition, the relative contribution of the different TES systems was determined, as well as the positive interaction with the power grid, which acted as a “virtual” energy storage system, in improving system performance.