Pasar al contenido principal

ELECTRIFICACION DEL ALMACENAMIENTO DE ENERGIA TERMICA PARA LA GENERACION EFICIENTE DE VAPOR EN PROCESOS INDUSTRIALES

PID2024-156068OB-C22

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal para la Investigación y el Desarrollo Experimental
Subprograma Subprograma Estatal de Generación de Conocimiento Científico-Técnico y Desarrollo Experimental
Convocatoria Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Año convocatoria 2024
Plan Estatal 2024-2027 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE SEVILLA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Economic Evaluation of a Concrete-Based Tank for Molten Salts in Concentrating Solar Power Plants

  • Ribezzo, Alessandro
  • Borri, Emiliano
  • Prieto, Cristina
  • Vérez, David
  • Cabeza, Luisa F.
Advancements in concentrating solar power (CSP) plants are essential for the wider adoption of these technologies. Increasing the operating temperature of the plants is one of the most promising ways to achieve further cost reductions and performance improvements. In this context, progress in supporting components—such as molten salt tanks—is critical to enable these advancements. This study compares a novel molten salt tank based on a refractory concrete formulation with a conventional design made from 347H stainless steel over the period 2015–2025. The prices of refractory concrete and stainless steel were analyzed across the decade to estimate the costs of the corresponding TES tanks in 2015 and 2025. The results showed that, while the concrete-based tank was more expensive than the conventional tank in 2015, the situation reversed by 2025, with the conventional stainless steel solution becoming 11% more expensive than the refractory concrete alternative. Additionally, an analysis of the producer price indexes for both materials highlighted that concrete exhibited a more stable price trend compared to stainless steel, which was subject to greater intra- and inter-year fluctuations. Finally, a brief examination of the 347H stainless steel production chain identified key causes of price volatility, such as the high geographic concentration of its main raw material extraction sites worldwide., This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE). Funded by Ministerio de Ciencia e Innovación y Universidades—Agencia Estatal de Investigación (MICIU/AEI/10.13039/501100011033) (RED2024-153629-T, PID2024-156068OB-C21, PID2024-156068OBC22). This paper is part of the RYC2023-044196-I, funded by MCIU/AEI/10.13039/501100011033 and FSE+. This work is partially supported by ICREA under the ICREA Academia program.
Repositori Obert UdL
Publicación Contribución de congreso (ConferenceOutput)

A systematic benchmark of thermal energy storage schemes in concentrating solar power applications

  • Tagle-Salazar, Pablo
  • Cabeza, Luisa F.
  • López-Román, Anton
  • Prieto, Cristina
Thermal energy storage (TES) plays a crucial role in enhancing the efficiency and reliability of concentrating solar power (CSP) plants by mitigating the intermittent nature of solar energy. Although molten salts are the predominant TES solution, alternative systems such as solid-state and latent heat storage offer promising advantages. This study investigated the impact of three TES technologies, namely two-tank molten salt, concrete-based storage, and phase change materials (PCMs), on the performance of CSP systems. By assessing the key performance indicators on an annual timescale and under identical operating conditions, this study elucidates the suitability of each TES technology for CSP plant operations. All three concepts demonstrated comparable performance at both the system and TES levels, with differences of less than 3%. The advantage of PCM lies in its substantial volume reduction of approximately 27% compared to molten salt, whereas concrete TES achieves similar results with a slight increase in volume relative to the molten salt TES., This work was partially funded by the Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (MICIU/AEI /10.13039/501100011033) (RED2024-153629-T), by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE), and by the Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (MICIU/AEI /10.13039/501100011033 and FSE+) (PID2024-156068OB-C21 and PID2024-156068OB-C22).). This work is partially supported by ICREA under the ICREA Academia programme. The authors at the University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Effective thermal conductivity measurement of anisotropic metal wool-loaded PCM matrix

  • López-Román, Antón
  • Mani Kala, Saranprabhu
  • Ribezzo, Alessandro
  • Zsembinszki, Gabriel
  • Borri, Emiliano
  • Megra, Kassahun Tadesse
  • Prieto, Cristina
  • Cabeza, Luisa F.
Metal wool is an emerging heat-transfer enhancer to improve the power density of thermal energy storage (TES) systems using phase change materials (PCMs). Previous experimental studies showed that metal wools can be placed in different ways and positions into TES tanks. Therefore, measuring the effective thermal conductivity of a metal wool-loaded PCM matrix is essential for determining the direction of maximum thermal-conductivity enhancement, given the anisotropic nature of metal wools. Most existing studies report the effective thermal conductivity of such matrices through steady-state measurements in TES tanks. This study uniquely assesses the effective thermal conductivity of a metal wool-loaded PCM matrix in all three axial directions of the samples. Copper and stainless-steel 434 are the metal wools, while n-octadecane and sodium nitrate are the PCMs examined in this study. Various metal wool-loaded PCM matrix samples were developed by varying the metal wool weight fraction in the PCM. Incorporating 20 wt% stainless-steel metal wool into the PCM enhances the effective thermal conductivity by 55% to 90% along all three axial directions compared to the bulk PCM. A maximum enhancement of 649% was observed for the copper metal wool-loaded n-octadecane matrix samples, along the direction aligned with the metal wool fibres. Results demonstrate that the anisotropic characteristics of metal wool become relevant when assessing the effective thermal conductivity of a metal wool-loaded PCM matrix, especially for PCM loaded with high thermal conductivity metal wool. Conclusions from this study also support the numerical simulation of TES systems, enabling more precise modelling for real-world applications., This project was funded by the European Union's Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This paper is part of the RYC2023-044196-I, PID2024-156068OB-C21, PID2024-156068OBC22funded by MCIU/AEI/10.13039/501100011033 and FSE+. This work was partially funded by the Ministerio de Ciencia e Innovacion ´ – Agencia Estatal de Investigacion ´ (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE). This work was partially funded by Ministerio de Ciencia e Innovacion ´ - Agencia Estatal de Investigacion ´ (AEI) (RED2024-153629-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Evaluation of the corrosion of metal-based containers in contact with molten salts at high temperature under inert atmosphere

  • Cabeza, Luisa F.
  • Martínez Alcocer, F. Rodrigo
  • Borri, Emiliano
  • Mani Kala, Saranprabhu
  • Escribà i Gelonch, Marc
  • Prieto, Cristina
The reliable deployment of high-temperature thermal energy storage (TES) systems in concentrated solar power (CSP) plants requires an accurate assessment of material compatibility under realistic operating conditions. However, conventional corrosion testing in air atmosphere does not adequately represent the inert environments typically used in TES tanks, potentially leading to overly conservative material selection. This study experimentally evaluates the corrosion behaviour of PCM–metal wool composite materials under inert atmosphere conditions representative of CSP operation. Sixteen molten salt formulations, including nitrate-, carbonate-, chloride-, and sulphate-based systems, were tested in contact with metallic fibres and structural alloys (SS 314, SS 434, and Alloy 20) over a wide temperature range. The results demonstrate that inert atmosphere significantly alters material compatibility. Several PCM formulations that previously failed under air conditions exhibit acceptable behaviour under inert atmosphere, highlighting the limitations of conventional testing approaches. Nitrate- and carbonate-based systems operating between 300 and 500 °C show good compatibility with conventional alloys, whereas chloride-rich systems above 500 °C remain highly corrosive regardless of the atmosphere. These findings define a clear operational window for safe material selection. Importantly, the incorporation of metallic wool as a conductive matrix does not introduce additional corrosion penalties within this window, supporting the feasibility of PCM–metal wool composites for enhanced TES performance. This work provides experimental validation of TES materials under representative conditions and demonstrates that inert atmosphere is a critical factor for realistic material qualification in CSP applications., This study was partially funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovacion ´ - Agencia Estatal de Investigacion ´ (AEI) (PID2021-123511OB-C31 – MCIN/AEI/10.13039/ 501100011033/FEDER, UE). Funded by Ministerio de Ciencia e Innovacion ´ y Universidades - Agencia Estatal de Investigacion ´ (MICIU/ AEI /10.13039/501100011033) (RED2024-153629-T, PID2024- 156068OB-C21, PID2024-156068OB-C22). This paper is part of the RYC2023-044196-I, funded by MCIU/AEI/10.13039/501100011033 and FSE + . This work is partially supported by ICREA under the ICREA Academia and Serra Hunter programmes. The authors at the University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Repositori Obert UdL
Publicación Artículo científico (JournalArticle)

Thermal conductivity of phase change materials in solid state at high temperature

  • Mani Kala, Saranprabhu
  • Ribezzo, Alessandro
  • Borri, Emiliano
  • Prieto, Cristina
  • Cabeza, Luisa F.
The portfolio of phase change material (PCM) candidates available for high temperature applications that are fully characterized in the solid-phase within these elevated temperature ranges is limited. In this study, 11 PCM candidates—previously proposed for high-temperature applications—were experimentally characterized in terms of solid-phase thermal conductivity at both room (20 °C) and high temperature (300 °C). The results revealed a substantial and general decrease in solid-phase thermal conductivity with increasing temperature, highlighting the importance of conducting thermal characterization at high temperature. These PCM candidates were subsequently compared with the few PCMs reported in the literature for similar applications and characterized within the same temperature ranges, by considering the solid-phase thermal conductivity analyzed in study, as well as the melting temperature and latent heat obtained from a previous study. Thanks to this, a comprehensive comparative map of PCM candidates fully characterized in the solid state at high temperature was finally presented (≥300 °C)., This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement HYBRIDplus (101084182). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. “This work was partially funded by the Ministerio de Ciencia e Innovaci´ on - Agencia Estatal de Investigaci´ on (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/ 501100011033/FEDER, UE)”. This paper is part of the RYC2023- 044196-I, funded by MCIU/AEI/10.13039/501100011033 and FSE+. This work is part of the PID2024-156068OB-C21 and PID2024- 156068OB-C22, funded by Ministerio de Ciencia e Innovaci´ on y Universidades - Agencia Estatal de Investigaci´ on MICIU/AEI/10.13039/ 501100011033 and FSE+. Funded by Ministerio de Ciencia e Innovaci´ on y Universidades - Agencia Estatal de Investigaci´ on (MICIU/ AEI/10.13039/501100011033) (RED2024-153629-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Evaluation of the corrosion of metal-based containers in contact with molten salts at high temperature under inert atmosphere

  • Cabeza, Luisa F.
  • Martínez Alcocer, F. Rodrigo
  • Borri, Emiliano
  • Mani Kala, Saranprabhu
  • Escribà i Gelonch, Marc
  • Prieto, Cristina
The reliable deployment of high-temperature thermal energy storage (TES) systems in concentrated solar power (CSP) plants requires an accurate assessment of material compatibility under realistic operating conditions. However, conventional corrosion testing in air atmosphere does not adequately represent the inert environments typically used in TES tanks, potentially leading to overly conservative material selection. This study experimentally evaluates the corrosion behaviour of PCM–metal wool composite materials under inert atmosphere conditions representative of CSP operation. Sixteen molten salt formulations, including nitrate-, carbonate-, chloride-, and sulphate-based systems, were tested in contact with metallic fibres and structural alloys (SS 314, SS 434, and Alloy 20) over a wide temperature range. The results demonstrate that inert atmosphere significantly alters material compatibility. Several PCM formulations that previously failed under air conditions exhibit acceptable behaviour under inert atmosphere, highlighting the limitations of conventional testing approaches. Nitrate- and carbonate-based systems operating between 300 and 500 °C show good compatibility with conventional alloys, whereas chloride-rich systems above 500 °C remain highly corrosive regardless of the atmosphere. These findings define a clear operational window for safe material selection. Importantly, the incorporation of metallic wool as a conductive matrix does not introduce additional corrosion penalties within this window, supporting the feasibility of PCM–metal wool composites for enhanced TES performance. This work provides experimental validation of TES materials under representative conditions and demonstrates that inert atmosphere is a critical factor for realistic material qualification in CSP applications., This study was partially funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement 101084182 (HYBRIDplus). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. This work was partially funded by the Ministerio de Ciencia e Innovacion ´ - Agencia Estatal de Investigacion ´ (AEI) (PID2021-123511OB-C31 – MCIN/AEI/10.13039/ 501100011033/FEDER, UE). Funded by Ministerio de Ciencia e Innovacion ´ y Universidades - Agencia Estatal de Investigacion ´ (MICIU/ AEI /10.13039/501100011033) (RED2024-153629-T, PID2024- 156068OB-C21, PID2024-156068OB-C22). This paper is part of the RYC2023-044196-I, funded by MCIU/AEI/10.13039/501100011033 and FSE + . This work is partially supported by ICREA under the ICREA Academia and Serra Hunter programmes. The authors at the University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Contribución de congreso (ConferenceOutput)

A systematic benchmark of thermal energy storage schemes in concentrating solar power applications

  • Tagle-Salazar, Pablo
  • Cabeza, Luisa F.
  • López-Román, Anton
  • Prieto, Cristina
Thermal energy storage (TES) plays a crucial role in enhancing the efficiency and reliability of concentrating solar power (CSP) plants by mitigating the intermittent nature of solar energy. Although molten salts are the predominant TES solution, alternative systems such as solid-state and latent heat storage offer promising advantages. This study investigated the impact of three TES technologies, namely two-tank molten salt, concrete-based storage, and phase change materials (PCMs), on the performance of CSP systems. By assessing the key performance indicators on an annual timescale and under identical operating conditions, this study elucidates the suitability of each TES technology for CSP plant operations. All three concepts demonstrated comparable performance at both the system and TES levels, with differences of less than 3%. The advantage of PCM lies in its substantial volume reduction of approximately 27% compared to molten salt, whereas concrete TES achieves similar results with a slight increase in volume relative to the molten salt TES., This work was partially funded by the Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (MICIU/AEI /10.13039/501100011033) (RED2024-153629-T), by the Ministerio de Ciencia e Innovación - Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/501100011033/FEDER, UE), and by the Ministerio de Ciencia, Innovación y Universidades - Agencia Estatal de Investigación (MICIU/AEI /10.13039/501100011033 and FSE+) (PID2024-156068OB-C21 and PID2024-156068OB-C22).). This work is partially supported by ICREA under the ICREA Academia programme. The authors at the University of Lleida would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Thermal conductivity of phase change materials in solid state at high temperature

  • Mani Kala, Saranprabhu
  • Ribezzo, Alessandro
  • Borri, Emiliano
  • Prieto, Cristina
  • Cabeza, Luisa F.
The portfolio of phase change material (PCM) candidates available for high temperature applications that are fully characterized in the solid-phase within these elevated temperature ranges is limited. In this study, 11 PCM candidates—previously proposed for high-temperature applications—were experimentally characterized in terms of solid-phase thermal conductivity at both room (20 °C) and high temperature (300 °C). The results revealed a substantial and general decrease in solid-phase thermal conductivity with increasing temperature, highlighting the importance of conducting thermal characterization at high temperature. These PCM candidates were subsequently compared with the few PCMs reported in the literature for similar applications and characterized within the same temperature ranges, by considering the solid-phase thermal conductivity analyzed in study, as well as the melting temperature and latent heat obtained from a previous study. Thanks to this, a comprehensive comparative map of PCM candidates fully characterized in the solid state at high temperature was finally presented (≥300 °C)., This project was funded by the European Union’s Horizon Europe Research and Innovation Programme under grant agreement HYBRIDplus (101084182). Views and opinions expressed are however those of the author(s) only and do not necessarily reflect those of the European Union or CINEA. Neither the European Union nor the granting authority can be held responsible for them. “This work was partially funded by the Ministerio de Ciencia e Innovaci´ on - Agencia Estatal de Investigaci´ on (AEI) (PID2021-123511OB-C31 - MCIN/AEI/10.13039/ 501100011033/FEDER, UE)”. This paper is part of the RYC2023- 044196-I, funded by MCIU/AEI/10.13039/501100011033 and FSE+. This work is part of the PID2024-156068OB-C21 and PID2024- 156068OB-C22, funded by Ministerio de Ciencia e Innovaci´ on y Universidades - Agencia Estatal de Investigaci´ on MICIU/AEI/10.13039/ 501100011033 and FSE+. Funded by Ministerio de Ciencia e Innovaci´ on y Universidades - Agencia Estatal de Investigaci´ on (MICIU/ AEI/10.13039/501100011033) (RED2024-153629-T). This work is partially supported by ICREA under the ICREA Academia programme. The authors would like to thank the Departament de Recerca i Universitats of the Catalan Government for the quality accreditation given to their research group (2021 SGR 01615). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Economic Evaluation of a Concrete-Based Tank for Molten Salts in Concentrating Solar Power Plants

  • Ribezzo, Alessandro
  • Borri, Emiliano
  • Prieto, Cristina
  • Vérez, David
  • Cabeza, Luisa F.
Advancements in concentrating solar power (CSP) plants are essential for the wider adoption of these technologies. Increasing the operating temperature of the plants is one of the most promising ways to achieve further cost reductions and performance improvements. In this context, progress in supporting components—such as molten salt tanks—is critical to enable these advancements. This study compares a novel molten salt tank based on a refractory concrete formulation with a conventional design made from 347H stainless steel over the period 2015–2025. The prices of refractory concrete and stainless steel were analyzed across the decade to estimate the costs of the corresponding TES tanks in 2015 and 2025. The results showed that, while the concrete-based tank was more expensive than the conventional tank in 2015, the situation reversed by 2025, with the conventional stainless steel solution becoming 11% more expensive than the refractory concrete alternative. Additionally, an analysis of the producer price indexes for both materials highlighted that concrete exhibited a more stable price trend compared to stainless steel, which was subject to greater intra- and inter-year fluctuations. Finally, a brief examination of the 347H stainless steel production chain identified key causes of price volatility, such as the high geographic concentration of its main raw material extraction sites worldwide., This work was partially funded by the Ministerio de Ciencia e Innovación—Agencia Estatal de Investigación (AEI) (PID2021-123511OB-C31—MCIN/AEI/10.13039/501100011033/FEDER, UE). Funded by Ministerio de Ciencia e Innovación y Universidades—Agencia Estatal de Investigación (MICIU/AEI/10.13039/501100011033) (RED2024-153629-T, PID2024-156068OB-C21, PID2024-156068OBC22). This paper is part of the RYC2023-044196-I, funded by MCIU/AEI/10.13039/501100011033 and FSE+. This work is partially supported by ICREA under the ICREA Academia program.