Pasar al contenido principal

DISEÑO DE TRANSCEPTORES RADIO ENERGETICAMENTE EFICIENTES Y RECONFIGURABLES CON FRONTHAUL OPTICO

RTI2018-095684-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSIDAD DE ZARAGOZA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

PSM-DMO: power save mode and discontinuous BLE mesh operation

  • Hernandez Solana, Angela
  • Pérez Díaz de Cerio, David|||0000-0003-0735-6811
  • García Lozano, Mario|||0000-0001-8155-9698
  • Valdovinos, Antonio
  • Valenzuela González, José Luis|||0000-0002-7238-2621
The Bluetooth Low Energy (BLE) mesh profile, standardized by the Bluetooth Special Interest Group (SIG), has an increasing interest in IoT solutions. However, the standard assumes that relay and friend nodes should be continuously scanning the channel awaiting any incoming transmissions. This could be very inefficient in terms of energy consumption, particularly in application scenarios where the backbone of the mesh network cannot be powered and traffic is infrequent. Hence, we present a novel strategy, named PSM-DMO, that minimizes the scan periods and thus, significantly reduces the overall energy consumption of the mesh network. PSM-DMO is defined as a new and optional feature for the currently published BLE mesh specifications, coexists with the standard operation, and is implemented without modifying the core of the specification. The proposal, that ensures the reliability of the mesh operation, can be used in BLE sensor networks that can tolerate a certain transmission delay. PSM-DMO replaces the continuous scan by a periodic but asynchronous polling process whereby the relay and sink nodes interrogate their neighbors about the existence of data to receive or to retransmit through the network. Nodes only go into scan mode during the period of time the mesh network will be involved in the transmission and dissemination. This period is estimated by the node which is the source of data, it is announced to its neighbors and it is propagated consecutively by all the relay nodes until the destination. PSM-DMO allows a theoretical reduction in the energy consumption of relay nodes up to 99.24 %., This work has been supported in part by the Spanish Ministry of Science through the projects RTI2018-099880-B-C32. RTI2018-095684-B-I00 and RTI2018-099063-B-I00 with ERFD funds, and by the Government of Aragon (Reference Group T31_20R)., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

Speeding up bluetooth mesh

  • Pérez Díaz de Cerio, David|||0000-0003-0735-6811
  • Hernandez Solana, Angela
  • García Lozano, Mario|||0000-0001-8155-9698
  • Valdovinos Bardají, Antonio
  • Valenzuela González, José Luis|||0000-0002-7238-2621
Bluetooth has constantly evolved from its cradle in 1997 to the last 5.2 version in 2020. With each update and amendment, it has gained in speed, range, and versatility. One of the latest introductions was the Bluetooth Mesh Profile (BMP) making it a technology suitable for a wide variety of applications. Nevertheless, BMP was designed to maintain the compatibility with Bluetooth version 4 devices already deployed in the market. This imposes some restrictions that place Bluetooth Mesh under other competing technologies like Zigbee or Thread in terms of throughput performance. In this paper we propose two mechanisms to overcome these limitations and take advantage of the new extended advertising capabilities introduced with Bluetooth 5. These mechanisms are presented as modifications to the current protocol stack to allow the transmission of larger data structures. Thus, it is possible to boost the throughput of Bluetooth Mesh making it suitable to more demanding applications like, for example, image transmission. The first proposal is designed as an adaptation layer to avoid modifying the standard in its current form. The second makes minimal changes to the frame structure at the different layers enabling the user to accommodate possible encapsulations (i.e., tunneling) without incurring IPv6-layer fragmentation. We have analyzed both solutions and compared them with the current BMP in terms of throughput, delay, and energy consumption for different channel conditions and network size. The results show that except for very small messages or poor channel conditions the proposals improve the throughput and delay of the current BMP., This work was supported in part by the Spanish Ministry of Science through the European Regional Development Funds (ERDF) under Project RTI2018-099880-B-C32, Project RTI2018-095684-B-I00, and Project RTI2018-099063-B-I00; and in part by the Government of Aragon (Reference Group) under Grant T31_20R., Peer Reviewed
UPCommons. Portal del coneixement obert de la UPC
Publicación Artículo científico (JournalArticle)

BMADS: BLE mesh asynchronous dynamic scanning

  • Pérez Díaz de Cerio, David|||0000-0003-0735-6811
  • Valenzuela González, José Luis|||0000-0002-7238-2621
  • García Lozano, Mario|||0000-0001-8155-9698
  • Hernandez Solana, Angela
  • Valdovinos, Antonio
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The Bluetooth low-energy (BLE) mesh profile, currently standardized by the Bluetooth Special Interest Group (SIG), assumes that friend and relay nodes should be continuously scanning the channel ready to receive any incoming transmissions (TXs). This is very inefficient in terms of energy consumption. Hence, we present BMADS, an asynchronous dynamic scanning mechanism designed to reduce the overall energy consumption of the mesh network. BMADS is implemented as a new feature for the currently published BLE mesh specifications without modifying its core. This feature reduces the scanning cycles of the nodes, but still ensuring the reliability. To make this possible, BMADS sends a new control message sequence before transmitting the data. This sequence puts the nodes into continuous scan mode, preparing the network for data TX. The proposal can be used in BLE sensor networks that can tolerate a certain TX delay and require especially low-energy consumption. BMADS allows a theoretical reduction in the energy consumption of the relay nodes up to 98%., This work has been funded by the Spanish Ministry of Science through the projects RTI2018-099880-B-C32, RTI2018-095684-B-I00, RTI2018-099063-B-I00 with ERFD funds and by the Government of Aragon (Reference Group T31 20R), Peer Reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Experimental Evaluation of Transmitted Signal Distortion Caused by Power Allocation in Inter-Cell Interference Coordination Techniques for LTE/LTE-A and 5G Systems

  • Hernandez-Solana, A.
  • García-Dúcar, P.
  • Valdovinos, A.
  • Garcia, J. E.
  • De Mingo, J.
  • Carro, P. L.
Error vector magnitude (EVM) and out-of-band emissions are key metrics for evaluating in-band and out-band distortions introduced by all potential non-idealities in the transmitters of wireless systems. As EVM is a measure of the quality of the modulated signal/symbols, LTE/LTE-A and 5G systems specify mandatory EVM requirements in transmission for each modulation scheme. This paper analyzes the influence of the mandatory satisfaction of EVM requirements on the design of radio resource management strategies (RRM) (link adaptation, inter-cell interference coordination), specifically in the downlink (DL). EVM depends on the non-idealities of the transmitter implementations, on the allocated power variations between the subcarriers and on the selected modulations. In the DL of LTE, link adaptation is usually executed by adaptive modulation and coding (AMC) instead of power control, but some flexibility in power allocation remains being used. LTE specifies some limits in the power dynamic ranges depending on the allocated modulation, which ensures the satisfaction of EVM requirements. However, the required recommendations concerning the allowed power dynamic range when inter-cell interference coordination (ICIC) and enhanced ICIC (eICIC) mechanisms (through power coordination) are out of specification, even though the EVM performance should be known to obtain the maximum benefit of these strategies. We perform an experimental characterization of the EVM in the DL under real and widely known ICIC implementation schemes. These studies demonstrate that an accurate analysis of EVM is required. It allows a better adjustment of the design parameters of these strategies, and also allows the redefinition of the main criteria to be considered in the implementation of the scheduler/link adaptation concerning the allocable modulation coding scheme (MCS) in each resource block. © 2013 IEEE.
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

BMADS: BLE mesh asynchronous dynamic scanning

  • Pérez Díaz de Cerio, David
  • Valenzuela González, José Luis
  • García Lozano, Mario
  • Hernandez Solana, Angela
  • Valdovinos, Antonio
© 2020 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works., The Bluetooth low-energy (BLE) mesh profile, currently standardized by the Bluetooth Special Interest Group (SIG), assumes that friend and relay nodes should be continuously scanning the channel ready to receive any incoming transmissions (TXs). This is very inefficient in terms of energy consumption. Hence, we present BMADS, an asynchronous dynamic scanning mechanism designed to reduce the overall energy consumption of the mesh network. BMADS is implemented as a new feature for the currently published BLE mesh specifications without modifying its core. This feature reduces the scanning cycles of the nodes, but still ensuring the reliability. To make this possible, BMADS sends a new control message sequence before transmitting the data. This sequence puts the nodes into continuous scan mode, preparing the network for data TX. The proposal can be used in BLE sensor networks that can tolerate a certain TX delay and require especially low-energy consumption. BMADS allows a theoretical reduction in the energy consumption of the relay nodes up to 98%., This work has been funded by the Spanish Ministry of Science through the projects RTI2018-099880-B-C32, RTI2018-095684-B-I00, RTI2018-099063-B-I00 with ERFD funds and by the Government of Aragon (Reference Group T31 20R), Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

PSM-DMO: power save mode and discontinuous BLE mesh operation

  • Hernandez Solana, Angela
  • Pérez Díaz de Cerio, David
  • García Lozano, Mario
  • Valdovinos, Antonio
  • Valenzuela González, José Luis
The Bluetooth Low Energy (BLE) mesh profile, standardized by the Bluetooth Special Interest Group (SIG), has an increasing interest in IoT solutions. However, the standard assumes that relay and friend nodes should be continuously scanning the channel awaiting any incoming transmissions. This could be very inefficient in terms of energy consumption, particularly in application scenarios where the backbone of the mesh network cannot be powered and traffic is infrequent. Hence, we present a novel strategy, named PSM-DMO, that minimizes the scan periods and thus, significantly reduces the overall energy consumption of the mesh network. PSM-DMO is defined as a new and optional feature for the currently published BLE mesh specifications, coexists with the standard operation, and is implemented without modifying the core of the specification. The proposal, that ensures the reliability of the mesh operation, can be used in BLE sensor networks that can tolerate a certain transmission delay. PSM-DMO replaces the continuous scan by a periodic but asynchronous polling process whereby the relay and sink nodes interrogate their neighbors about the existence of data to receive or to retransmit through the network. Nodes only go into scan mode during the period of time the mesh network will be involved in the transmission and dissemination. This period is estimated by the node which is the source of data, it is announced to its neighbors and it is propagated consecutively by all the relay nodes until the destination. PSM-DMO allows a theoretical reduction in the energy consumption of relay nodes up to 99.24 %., This work has been supported in part by the Spanish Ministry of Science through the projects RTI2018-099880-B-C32. RTI2018-095684-B-I00 and RTI2018-099063-B-I00 with ERFD funds, and by the Government of Aragon (Reference Group T31_20R)., Peer Reviewed, Postprint (published version)
Recercat. Dipósit de la Recerca de Catalunya
Publicación Artículo científico (JournalArticle)

Speeding up bluetooth mesh

  • Pérez Díaz de Cerio, David
  • Hernandez Solana, Angela
  • García Lozano, Mario
  • Valdovinos Bardají, Antonio
  • Valenzuela González, José Luis
Bluetooth has constantly evolved from its cradle in 1997 to the last 5.2 version in 2020. With each update and amendment, it has gained in speed, range, and versatility. One of the latest introductions was the Bluetooth Mesh Profile (BMP) making it a technology suitable for a wide variety of applications. Nevertheless, BMP was designed to maintain the compatibility with Bluetooth version 4 devices already deployed in the market. This imposes some restrictions that place Bluetooth Mesh under other competing technologies like Zigbee or Thread in terms of throughput performance. In this paper we propose two mechanisms to overcome these limitations and take advantage of the new extended advertising capabilities introduced with Bluetooth 5. These mechanisms are presented as modifications to the current protocol stack to allow the transmission of larger data structures. Thus, it is possible to boost the throughput of Bluetooth Mesh making it suitable to more demanding applications like, for example, image transmission. The first proposal is designed as an adaptation layer to avoid modifying the standard in its current form. The second makes minimal changes to the frame structure at the different layers enabling the user to accommodate possible encapsulations (i.e., tunneling) without incurring IPv6-layer fragmentation. We have analyzed both solutions and compared them with the current BMP in terms of throughput, delay, and energy consumption for different channel conditions and network size. The results show that except for very small messages or poor channel conditions the proposals improve the throughput and delay of the current BMP., This work was supported in part by the Spanish Ministry of Science through the European Regional Development Funds (ERDF) under Project RTI2018-099880-B-C32, Project RTI2018-095684-B-I00, and Project RTI2018-099063-B-I00; and in part by the Government of Aragon (Reference Group) under Grant T31_20R., Peer Reviewed, Postprint (published version)