Pasar al contenido principal

CONFORMADOR DE HAZ FOTONICO BASADO EN FIBRA OPTICA MULTI-NUCLEO PARA REDES CELULARES BEYOND-5G

RTI2018-101296-B-I00

•
Nombre agencia financiadora Agencia Estatal de Investigación
Acrónimo agencia financiadora AEI
Programa Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Convocatoria Proyectos I+D+i Retos de Investigación
Año convocatoria 2018
Plan Estatal 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Centro beneficiario UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Linear Response Modeling of High Luminous Flux Phosphor-Coated White LEDs for VLC

  • Salvador-Llàcer, Pau|||0000-0002-2197-4942
  • Valls Coquillat, Javier|||0000-0002-9390-5022
  • Corral, Juan L.|||0000-0003-0857-5207
  • Almenar Terre, Vicenç|||0000-0002-8742-2315
  • Canet Subiela, Mª José|||0000-0002-6765-9219
[EN] The widespread deployment of LEDs for illumination purposes has open the door to the use of these devices for visible light communications (VLC). Most lighting fixtures are mounted with phosphor-based white LEDs, and a driver connected to the LED is also required for VLC. This paper shows that the parasitic effects introduced by this setup change the frequency response of the intrinsic LED. A linear model to characterize the whole setup is proposed, as well as a methodology to extract its parameters. This methodology allows the designer to characterize the frequency response of LEDs without the additional difficulty of knowing the specific parasitic components introduced by the setup. The proposed model offers an accurate estimation of the slope of the LED frequency response in order to broaden the frequency range in which the model is useful to characterize and simulate VLC links. This was corroborated with the characterization of three commercial white LEDs whose measured and modeled frequency responses matched perfectly.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Remote Photonic THz Generation Using an Optical Frequency Comb and Multicore Fiber

  • Morant, Maria
  • González-Guerrero, Luis
  • Renaud, Cyril C.
  • Llorente, Roberto
[EN] This paper proposes and demonstrates a photonic THz generation technique based on an optical frequency comb and multicore fiber (MCF) transmission, with the advantage of remote generation with great reconfigurability and reduced digital signal processing (DSP). The feasibility of the proposed technique is evaluated experimentally comparing the performance when transmitting a data wavelength and a local oscillator for optical heterodyning over a single core or over different cores in a 1-km MCF link. The proposed remote photonic THz generation technique is demonstrated employing a 16QAM 12.5 GBd signal. A short wireless transmission at 183 GHz center frequency with 0.25 m antenna-separation is achieved after 1 km MCF, meeting the soft-decision decision forward error correction (SD-FEC) bit error rate (BER) recommendation of 2 center dot 10(-2). The analysis includes the received photocurrent range for which the BER meets the standard hard-decision forward error correction (HD-FEC) recommendation of 3.8 center dot 10(-3) BER. The BER performance is analyzed considering different DSP configurations, with and without frequency offset estimation (FOE) and decision-driven least mean squares (DD LMS) equalization. The performance of the remote photonic THz generation technique is evaluated comparatively against traditional free-running laser transmission over MCF, confirming the advantage of using comb generation to reduce the frequency offset fluctuation and simplify the DSP., This work was supported by Spanish State Research Agency under Grants PID2019-106163RJ-I00/AEI/10.13039/501100011033 MULTICORE+ and MINECO/FEDER UE RTI2018-101296-B-I00 MULTI-BEAM5G projects, in part by the European Union'sHorizon 2020 Research and Innovation Programme underGrant H2020-EU.2.1.1.-762119 ULTRAWAVE, and in part by the Engineering and Physical Sciences Research Council under Grant EPSRC EP/P003990/1 COALESCE. The work of Maria Morant supported by Generalitat Valenciana under Grant BEST/2019/047.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Integrated wireless-optical backhaul and fronthaul provision through multicore fiber

  • Gonzalez Guerrero, Luis
  • Li, Tongyun
  • Fice, Martyn J.
  • Seeds, Alwyn J.
  • White, Ian H.
  • Penty, Richard V.
  • Renaud, Cyril C.
  • Maria Morant|||0000-0001-5565-7788
  • Roberto Llorente|||0000-0003-4799-2564
[EN] In this paper we propose multicore fiber (MCF) as the medium to transport the different signals associated with various wireless applications (ranging from access to fronthauling and backhauling) from the baseband unit (BBU) to the cell-site. Using 1 km of a 7-core MCF, we simultaneously transmit fronthaul and backhaul signals from the BBU to the cell site, where they are converted to carrier frequencies in the mm-wave and sub-THz band, respectively. The backhaul is evaluated with a 12.5 GBd 16-quadrature amplitude modulation (QAM) signal, whereas the fronthaul is evaluated with a 7 Gbit/s on-off keying (OOK) signal carrying 14 LTE-compatible channels. The fronthaul signal is generated with a novel compression technique that achieves an efficiency 3-times higher than the one obtained with the common public radio interface (CPRI) protocol. Optical heterodyining is implemented at the cell site for optical-to-RF conversion. The local oscillator (LO) signal required for optical heterodyning is transmitted in a dedicated core, reducing the system complexity and enabling its straight-forward reuse for uplink (UL) transmission. The experimental demonstration includes the simultaneous full-duplex transmission of both the fronthaul and backhaul signals, using 6 cores of the MCF at the same time and achieving a gross data rate of 57 Gbit/s., This work was supported in part by the European Union Horizon 2020 Research and Innovation Program Terahertz Based Ultra High Bandwidth Wireless Access Networks (TERAPOD) under Grant 761579, in part by the Engineering and Physical Sciences Research Council through the Converged Optical and Wireless Access Networks (COALESCE) under Grant EP/P003990/1, and in part by the Spain I CD CI projects under Grant PID2019-106163RJ-I00/AEI/10.13039/501100011033 MULTICORE C and Grant MINECO/FEDER UE RTI2018-101296-B-I00 MULTI-BEAM5G. The work of Maria Morant was supported by the Generalitat Valenciana under Grant BEST/2019/047.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Datos de investigación Set de datos (Dataset)

Model and Methodology to Characterize Phosphor-Based White LED Visible Light Communication Links [Dataset]

  • Salvador-Llàcer, Pau|||0000-0002-2197-4942
  • Almenar Terre, Vicenç|||0000-0002-8742-2315
  • Corral, Juan L.|||0000-0003-0857-5207
  • Valls Coquillat, Javier|||0000-0002-9390-5022
  • Canet Subiela, Mª José|||0000-0002-6765-9219
[EN] LED lighting has become the standard solution for illumination purposes thanks to its energy efficiency. Nowadays, there is growing interest in the use of LEDs for data transmission to develop future-generation communication systems. The low cost and widespread deployment of phosphor-based white LEDs make them the best candidate for visible light communications (VLC), although they have a limited modulation bandwidth. This paper presents a simulation model of a VLC link based on phosphor-based white LEDs and a method to characterize the VLC setup used to perform the data transmission experiments. Specifically, the simulation model incorporates the frequency response of the LED, the noise levels coming from the lighting source and the acquisition electronics, and the attenuation due to both the propagation channel and the angular misalignment between the lighting source and the photoreceiver. In order to validate the suitability of the model for VLC, carrierless amplitude phase (CAP) and orthogonal frequency division multiplexing (OFDM) modulation signals were employed for data transmission, and simulations with the proposed model and measurements over the equivalent scenario show high agreement.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Multi-beamforming provided by dual-wavelength true time delay PIC and multicore fiber

  • Maria Morant|||0000-0001-5565-7788
  • Roberto Llorente|||0000-0003-4799-2564
  • Trinidad, Ailee
  • Tangdiongga, Eduward
  • Koonen, Ton
[EN] This paper presents a multi-beamformer based on a dual-wavelength photonic integrated circuit (PIC) and multicore fiber (MCF) capable of providing independent delay tuning to two separate beams modulated on different optical carriers. This implementation enables a centralized control of the photonic beamformer, connecting each element of a phase array antenna with a dedicated core of a MCF link and controlling the induced delay (resulting steering angle) by thermo-optically adjusting the heaters of the PIC. The dual-wavelength PIC implements true time delay (TTD) based on optical ring resonators (ORRs). Six different ORR heaters¿ configurations are evaluated experimentally, obtaining an induced delay of up to 328 ps at 19 GHz RF. With a measured delay resolution of 4 ps, it is recommended to increase/decrease the delay in small steps (between 10 and 30 ps) in order to keep the switching time in the ms range. Higher delays increments can be induced within longer switching time, e.g. 328 ps requires 1.68 s to stabilize the heaters. The performance demonstration includes the dual-wavelength transmission over 1-km of 7-core MCF and evaluates single-carrier data signals in the K-band centered in 19 GHz RF with up to 4 GHz bandwidth (BW). Operation with OFDM standard WiFi and WiMAX signals is also demonstrated experimentally. A delay of 328 ps can be induced to data signals at 19 GHz RF with up to 3-GHz BW, while 4-GHz BW signals can operate with up to 166 ps delay increment.An almost constantEVM is obtained for each BW below 3 GHz, confirming that changing the beam-steering angle does not affect the quality of the signal., This work was supported in part by Spain National Plan MINECO/FEDER UE RTI2018-101296-B-I00 MULTI-BEAM5G and in part by Fundacion BBVA Leonardo HYPERCONN and Dutch FreeBEAM projects. The work of A. Trinidad was supported by Dutch NWO Zwaartekracht on Integrated Nanophotonics.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Photonic Frequency Conversion of OFDM Microwave Signals in a Wavelength-Scale Optomechanical Cavity

  • Mercadé, Laura|||0000-0002-4994-7727
  • Maria Morant|||0000-0001-5565-7788
  • Griol Barres, Amadeu
  • Roberto Llorente|||0000-0003-4799-2564
  • Martínez, Alejandro|||0000-0001-5448-0140
[EN] Optomechanical (OM) cavities enable coupling of near-infrared light and GHz-frequency acoustic waves in wavelength-scale volumes. When driven in the phonon lasing regime, an OM cavity can perform simultaneously as a nonlinear mixer and a local oscillator¿at integer multiples of the mechanical resonance frequency¿in the optical domain. In this work, this property is used to demonstrate all-optical frequency down- and up-conversion of MHz-bandwidth orthogonal frequency division multiplexed signals compliant with the IEEE 802.16e WiMAX wireless standard at microwave frequencies. To this end, a silicon OM crystal cavity (OMCC), supporting a breathing-like mechanical resonance at fm ¿3.9 GHz and having a foot-print ¿ 10 um^2, which yields frequency conversion efficiencies better than ¿17 dB in both down- and up-conversion processes at mW-scale driving power, is employed. This work paves the way toward the application of OMCCs in low-power all-photonic processing of digitally modulated microwave signals in miniaturized silicon photonics chips., The authors acknowledge funding from the H2020 Future and Emerging Technologies program (projects PHENOMEN 713450 and SIOMO 945915); the Spanish State Research Agency (PGC2018-094490-BC21, PID2019-106163RJ-I00/AEI/10.13039/501100011033 MULTICORE+ and MCIU/AEI/FEDER UE RTI2018-101296-B-I00 MULTI-BEAM5G); Generalitat Valenciana (PPC/2021/042, BEST/2020/178, PROMETEO/2019/123 and IDIFEDER/2018/033); and the UPV Programa de Ayudas de Investigacion y Desarrollo (PAID-01-16).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

On the Performance and Power Consumption of Bias-T Based Drivers for High Speed VLC

  • Salvador-Llàcer, Pau|||0000-0002-2197-4942
  • Valls Coquillat, Javier|||0000-0002-9390-5022
  • Canet Subiela, Mª José|||0000-0002-6765-9219
  • Almenar Terre, Vicenç|||0000-0002-8742-2315
  • Corral, Juan L.|||0000-0003-0857-5207
[EN] LED lamps have become the predominant technology for lighting thanks to their low power consumption. Recently, the joint use of these devices for lighting and data transmission has aroused interest in the research community as a future green communication technology. During this time, many of the advances developed in this area have been demonstrated with experimental setups using LED drivers based on bias-T, thanks to their ease to combine signal modulation and LED bias. This article discusses the impact of the output impedance of the bias-T driver and the driver-LED connection parasitics on the performance and energy efficiency of the VLC system. It is concluded that the output impedance of the driver not only affects energy efficiency but also modifies the frequency response and, therefore, the LED's capacity to be modulated. A low output impedance driver is shown to offer a substantial improvement in the energy efficiency of the VLC driver., Thisworkwas supported in part by MCIN/AEI/10.13039/501100011033, in part by European Union (ERDF A way of making Europe) under Grants RTI2018101658-B100 and RTI2018-101296-B-I00, and in part byMinisterio de Ciencia, Innovacion y Universidades para la Formacion de Profesorado Universitario under Grant FPU19/04648.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Model and Methodology to Characterize Phosphor-Based White LED Visible Light Communication Links

  • Salvador-Llàcer, Pau|||0000-0002-2197-4942
  • Almenar Terre, Vicenç|||0000-0002-8742-2315
  • Corral, Juan L.|||0000-0003-0857-5207
  • Valls Coquillat, Javier|||0000-0002-9390-5022
  • Canet Subiela, Mª José|||0000-0002-6765-9219
[EN] LED lighting has become the standard solution for illumination purposes thanks to its energy efficiency. Nowadays, there is growing interest in the use of LEDs for data transmission to develop future-generation communication systems. The low cost and widespread deployment of phosphor-based white LEDs make them the best candidate for visible light communications (VLC), although they have a limited modulation bandwidth. This paper presents a simulation model of a VLC link based on phosphor-based white LEDs and a method to characterize the VLC setup used to perform the data transmission experiments. Specifically, the simulation model incorporates the frequency response of the LED, the noise levels coming from the lighting source and the acquisition electronics, and the attenuation due to both the propagation channel and the angular misalignment between the lighting source and the photoreceiver. In order to validate the suitability of the model for VLC, carrierless amplitude phase (CAP) and orthogonal frequency division multiplexing (OFDM) modulation signals were employed for data transmission, and simulations with the proposed model and measurements over the equivalent scenario show high agreement., This research was funded by MCIN/AEI/10.13039/501100011033; by the European Union's "ERDF A way of making Europe" grant numbers PID2021-126514OB-I00 and RTI2018-101296-B-I00; and by the Ministerio de Ciencia, Innovacion y Universidades para la Formacion de Profesorado Universitario, grant number FPU19/04648.