Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Energy management strategies comparison for a parallel full hybrid electric vehicle using Reactivity Controlled Compression Ignition combustion

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Carlucci, Paolo
  • Valletta, Andrea
  • Martínez-Boggio, Santiago Daniel
[EN] Reactivity Controlled Compression Ignition combustion technology potentials are well known for the capability to drastically reduce the engine-out nitrogen oxides and soot emissions simultaneously. Its implementation in mid-term low-duty diesel engines can be beneficial to meet the upcoming regulations. To explore the potential of this solution, experimental data are used from a compression ignition 1.9 L engine, which is operated under two combustion-modes: Reactivity Controlled Compression Ignition and conventional diesel combustion. Meanwhile, also the carbon dioxide emissions limitations must be fulfilled. To achieve this goal, the benefits associated to powertrain electrification in terms of fuel economy, can be joined with the benefits of RCCI combustion. To do so, two different supervisory control strategies are compared: Adaptive Equivalent Minimization Control Strategy and Rule-Based Control strategy, while dynamic programming is used to size the electric grid of the powertrain to provide the best optimal solution in terms of fuel economy and emissions abatement. The analysis of the designed hybrid powertrain is carried out numerically with GT-Suite and Matlab-Simulink software. The results show a great potential of the parallel full-hybrid electric vehicle powertrain equipped with the dual-mode engine to reduce the engine-out emissions, also to increase fuel economy with respect to the homologation fuel consumption of the baseline vehicle. The optimal supervisory control strategy was found to be the emissions-oriented Adaptive Equivalent Minimization Control Strategy, which scores a simultaneous reduction of 12% in fuel consumption, 75% in engine-out nitrogen oxides emissions and 82% in engine-out soot, with respect to the baseline conventional diesel combustion engine vehicle., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (SP20180148).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Methanol and OMEx as fuel candidates to fulfill the potential EURO VII emissions regulation under dual-mode dual-fuel combustion

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
  • Guzmán-Mendoza, María Gabriela
[EN] Recent investigations show that there are different combustion strategies that promise to achieve higher efficiencies in internal combustion engines. Advanced combustion modes such as reactivity controlled compression ignition (RCCI) and dual-mode dual-fuel (DMDF) have proven to be able to achieve low NOx and soot engine-out emissions while being able to operate over the complete engine map. On another front, intensive research has been done in the fuels field. Oxygenated fuels, like oxymethylene dimethyl ethers (OMEx) and methanol, are of special interest because of their potential to reduce the soot emissions, while allowing to adjust parameters, such as EGR, to higher values to also reduce NOx emissions and avoid other problems like excessive in-cylinder peaks of pressure. In this research, the effects of diesel-methanol and OMEx-gasoline fuels were studied on a dual-mode dual-fuel (DFDM) multi-cylinder engine at 1800 rpm for various loads (25, 50, 80 and 100%). To do so, a dedicated calibration to optimize the brake thermal efficiency while trying to maintain NOx and soot emissions under EURO VI limitations was applied. Then, the combustion characteristics, performance and emissions results are compared to a base diesel-gasoline case. Boundary conditions (intake pressure, temperature and air mass) for each fuel combination where similar, with the exception of the premixed energy ratio, which was on average 20% lower for diesel-methanol. Each fuel combination was, weighted against each other by means of an merit function, where the fuel combination with the lowest value has the closest approximation to ideal BSFCeq, BSNOx, BSSoot, BSCO and BSHC targets. Results show that diesel-methanol presents no significant differences with respect to diesel-gasoline in terms of equivalent BSFCeq and NOx, while the substitution of diesel by OMEx in the dual-mode dual-fuel combustion has the potential of, although penalizing HC and CO emissions, not only achieving the EURO VI NOx (0.4 g/kWh) limits but also the future potential EURO VII (0.2 g/kWh) as well because of a negligible soot production that allows using EGR levels of up to 50%., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA201787694-R). The authors also acknowledge the Universitat Politecnica de Val`encia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Assessment of a complete truck operating under dual-mode dual-fuel combustion in real life applications: Performance and emissions analysis

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
  • Gaillard,Patrick
[EN] The dual-mode dual-fuel (DMDF) strategy has been demonstrated to be a potential combustion mode to cover all the engine map with low-to-moderate NOx and soot emissions and high efficiency simultaneously. This can be accomplished by modifying the injection strategy to promote a fully premixed or a dual-fuel diffusive combustion depending on the operating conditions. The main limitation of the DMDF are the high concentrations of unburned hydrocarbons and carbon monoxide coupled with low exhaust temperatures, which can be a challenge for the stock diesel oxidation catalyst (DOC). Moreover, the use of a diffusive combustion combined with high EGR rates to avoid mechanical issues at high load enhances the soot formation, which can compromise the final soot levels in a homologation cycle. To evaluate these aspects, this work studies the performance and emissions of a DMDF truck concept along a WHVC and different in-service conformity cycles through vehicle systems simulations. For both types of cycles, five payloads were tested (0%, 25%, 50%, 75% and 100%) to evaluate the impact of this parameter on the operating points distribution inside the DMDF map. The first results show that the DMDF concept provides engine-out NOx levels below the EUVI regulation at normative payload (50%) with similar fuel consumption than the conventional diesel truck. On the other hand, the engine-out HC and CO emissions exceed their respective limits in all the cases, while the engine-out soot emissions only reach the EUVI levels up to 25% payload. By this reason, the stock DOC and diesel particulate filter from the conventional diesel truck were modelled and fitted to the DMDF truck model. The results evidenced that the use of these two ATS allows to achieve the EUVI limits in terms of tailpipe HC, CO and soot independently on the cycle and payload analyzed. Moreover, considering the tailpipe emissions values achieved with ATS at 50% payload, it can be inferred that both devices could be downsized for the DMDF application as compared to the conventional ATS for diesel applications., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge European Regional Development Fund (FEDER) and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Polit`ecnica de Val`encia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (SP20180148). The author R. Sari acknowledges the financial support from the Spanish ministry of science innovation and universities under the grant ``Ayudas para contratos predoctorales para la formaci ' on de doctores"(PRE2018-085043).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computational optimization of the dual-mode dual-fuel concept through genetic algorithm at different engine loads

  • Xu, Guangfu
  • Jia, Ming
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • García Martínez, Antonio|||0000-0001-5783-4936
[EN] The diesel/gasoline dual-mode dual-fuel (DMDF) combustion concept was optimized in a compression-ignition engine by combining the computational fluid dynamics (CFD) simulations with the genetic algorithm. Seven operating parameters with remarkable influences on the engine performance were chosen as the variables to be optimized for simultaneously minimizing the fuel efficiency, nitrogen oxides (NOx), and soot emissions. Moreover, the potential of the further improvement of the DMDF combustion concept was discussed, and the rationality of this strategy was demonstrated. The results indicate that, at low load, simultaneous improvement of the fuel economy and emissions can be realized by strengthening the homogeneous combustion. At mid load, the fuel economy can be improved by reducing the heat transfer losses, while the NOx emissions are sacrificed to some extent. At high load, improved fuel economy can be realized by transferring a part of diffusion combustion to premixed reactivity-controlled compression ignition (RCCI) combustion. Concerning the operating parameters, lower intake temperature is beneficial to decrease the transfer losses, and the control of intake temperature is crucial for the stable operation of DMDF combustion under wide load conditions. Overall, gross indicated thermal efficiency above 45% is achieved, and the NOx and soot emission can be maintained under the Euro 6 standard for the test load range., This work was partially supported by the National Natural Science Foundation of China (Grant Nos. 51961135105 and 91641117) and China Postdoctoral Science Foundation (Grant No. 2019M661094). The experimental results used in this investigation were obtained in a project funded by VOLVO Group Trucks Technology. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Potential of bio-ethanol in different advanced combustion modes for hybrid passenger vehicles

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
  • Roso, Vinicius Ruckert
  • Souza Alvarenga Santos, Nathalia Duarte
[EN] The strong new restrictions in the vehicle CO2 emissions together with the instability of the fossil fuels reserves reinforces the necessity to continue developing high efficiency combustion engines that operate with renewable energy sources. Bio-ethanol appears as a potential fuel to replace well-established fossil fuels, such as gasoline, due to the overall carbon neutral emission. In addition, the high-octane number allows to increase the compression ratio of the engine to improve the thermal efficiency. Apart from the CO2, the emissions legislation restricts the NOx and particle matter emissions to ultra-low values, and they will continue decreasing down to almost zero. In this work, two advanced dual-fuel combustion modes using bio-ethanol as main fuel are studied. A pre-chamber ignition system (PCIS) using bio-ethanol and hydrogen, and a reactivity-controlled compression ignition (RCCI) combustion mode operating with bio-ethanol/diesel was selected due to the potential to reduce NOx emissions. These combustion technologies were studied by a numerical 0-D vehicle simulations in homologation and real-life driving cycles for a range extender hybrid powertrain. As a baseline, the original manufacturer spark ignition (SI) no-hybrid powertrain fueled with pure bio-ethanol was used. The powertrain components and control system were optimized to obtain the maximum overall vehicle efficiency, and low CO2-NOx emissions. Finally, a life cycle analysis (LCA) was performed to study the global potential of the bio-ethanol to reduce greenhouse gas (GHG) emissions. A battery electric vehicle (BEV) and a gasoline SI no-hybrid vehicle were added for comparison. The results show that the RCCI mode presents the highest potential to reduce the NOx emissions. However, the PCIS allows to reduce the tank to wheel CO2 emissions up to 60 g/km when high rates of H2 are used. The LCA-GHG for the vehicles using bio-ethanol is 50% and 95% lower than a BEV and SI-gasoline vehicle, respectively., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (SP20180148). The authors also acknowledge CAPES and the Post-Graduation Program in Mechanical Engineering at UFMG-Brazil for the support provided.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effectiveness of hybrid powertrains to reduce the fuel consumption and NOx emissions of a Euro 6d-temp diesel engine under real-life driving conditions

  • Luján, José M.|||0000-0001-6133-8943
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago
[EN] Recent investigations demonstrated that the real-world driving conditions differ from those proposed in the homologation cycles. This provokes that the emissions levels in real-life conditions exceed the normative values, as shown in the recent scandal related to the NOx emissions from the passenger cars equipped with diesel engines. On the other hand, the upcoming emissions regulations will limit the CO2 emissions to very low levels, which demands a further optimization of the existing technology. One way to reduce the NOx and CO2 emissions is by electrifying the powertrain in a certain degree. The objective of this work is to evaluate the potential of implementing a parallel (P2) hybrid architecture in a compact car (class C) equipped with a diesel 1.6 Euro 6d-temp engine to reduce the emissions and fuel consumption in homologation and real-life driving cycles. This has been done using a OD numerical vehicle model and the experimental engine maps of fuel consumption and emissions measured at steady state conditions. After that, the transient conditions were simulated in homologation cycles and real-life driving cycles measured by the authors in Spain. The numerical model was validated against experimental tests carried out in an active engine test bench, evidencing differences below 4% under the worldwide harmonized light vehicles test cycle (WLTC). In the real-life cycles, the hybridization of the powertrains improves the fuel consumption for all types of driving cycles (urban, combined and highway). The major benefits are obtained in urban driving cycles, with gains up to 50% in fuel consumption and CO2 emissions. In addition, the improvements in real-life conditions are higher than in the urban phase of the homologation cycles. On the contrary, combined real-life cycles (urban + rural + highway) show lower benefits than the homologation cycle. This is due to different energy management strategy that needs to be adapted to each driving situation. Lastly, it was found that, contrarily to the case of the homologation cycle, the NOx emissions are not reduced with the hybridization of the diesel powertrain in real-life conditions. Thus, to achieve 2021 CO2 target (95 g/km) and to reduce aftertreatment systems in diesel engines, other vehicles technologies need to be added to the full hybridization., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Computational optimization of the piston bowl geometry for the different combustión regimes of the dual-mode dual-fuel (DMDF) concept through an improved genetic algorithm

  • Xu, Guangfu
  • Jia, Ming
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
[EN] Focusing on the dual-mode dual-fuel (DMDF) combustion concept, a combined optimization of the piston bowl geometry with the fuel injection strategy was conducted at various loads. An improved genetic algorithm was introduced in this study, which is superior in searching for the global optimal solutions. The optimal piston bowl shape coupled with the corresponding injection strategy was summarized at the various loads. The results show that the piston bowl geometry optimization can further improve the thermal efficiency with 1.4%, 4.4%, and 1.4% percentage points for the low, mid, and high loads, respectively. An indicated thermal efficiency up to 51.8% can be realized at mid load. Meanwhile, for all the optimal cases, NOx and soot emissions can meet the Euro VI limits. At low and mid loads, both the open and re-entrant type piston bowl can be equipped, while the high load only prefers the open type piston bowl for the DMDF mode. The re-entrant type or deep piston bowls are superior in organizing strong in-cylinder flow, which is beneficial for the fuel/air mixing. The open type or shallow piston bowls are helpful for reducing the heat transfer losses owing to the less heat transfer surface area. Furthermore, a correlation analysis was conducted to investigate the sensitivity of engine performance to the piston geometric parameters and injection parameters. It is concluded that the fuel injection event becomes more important for managing the engine performance as load increases. Among the injection parameters, the influence of the fuel injection timings and injection pressure on engine performance is more obvious. The piston geometric parameters play more significant roles in the heat transfer losses than the injection parameters for all loads. Among the geometric parameters, the most influential parameters are the width and open extent of the piston bowl. The heat transfer loss energy fraction can be well decreased with a wider and more open piston bowl., This work was partially supported by the National Natural Science Foundation of China (Grant Nos. 51961135105 and 91641117) and Postdoctoral Research Foundation of China (Grant Nos. 2019M661094 and 2020T130075). The experimental results used in this investigation were obtained in a project funded by VOLVO Group Trucks Technology. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politecnica de Val`encia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Clean and efficient dual-fuel combustion using OMEx as high reactivity fuel: comparison to diesel-gasoline calibration

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
[EN] From previous results in a single-cylinder engine platform, it can be concluded that the dual-mode dual-fuel (DMDF) concept can be a potential solution to overcome the major constraints found with other single-fuel low temperature combustion modes. To extend these findings to a real application, this work evaluates the potential of the diesel-gasoline DMDF concept on a multi-cylinder 8L engine in terms of performance and emissions. To do this, a full engine calibration map was obtained following a specific methodology. The emissions results show that diesel-gasoline DMDF allows to achieve EURO VI NOx and soot emissions in a great portion of the engine map. Nonetheless, the levels of these pollutant at high load conditions exceed the EURO VI limits by far due to the need of implementing a diffusive combustion strategy with high EGR levels to avoid excessive in-cylinder pressure gradients. To mitigate this issue, the use of Oxymethylene ether (OMEx) instead of diesel fuel is proposed. A dedicated engine calibration was developed for the OMEx-gasoline DMDF concept following the same methodology. The results show that the oxygen content in the OMEx molecule allows to achieve a fully EUVI compliant engine calibration in terms of NOx with engine-out soot levels lower than 0.01 g/kWh. Moreover, due to the lower stoichiometric air-fuel ratio with this fuel, the air management system requirements are lower, reducing the pumping losses and increasing the brake thermal efficiency in most of the calibration map., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA201787694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (SP20180148). The author R. Sari acknowledges the financial support from the Spanish ministry of science innovation and universities under the grant "Ayudas para contratos predoctorales para la formacion de doctores"(PRE2018085043).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Optimization of the parallel and mild hybrid vehicle platforms operating under conventional and advanced combustion modes

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago
[EN] The stringent regulations, increased global temperature and customer demand for high fuel economy have led to rapid developments of different alternative propulsion solutions in the last decade, with special attention to the electrified vehicles. The combination of electric machines with conventional powertrains allows to diversify the powertrain architectures. In addition, alternative combustion modes as reactivity controlled compression ignition (RCCI) have been shown to provide simultaneous ultra-low NOx and soot emissions with similar or better thermal efficiency than conventional diesel combustion (CDC). Therefore, the combination of both technologies creates a promising horizon to be implemented in commercial vehicles of the near future. In this work, experimental and numerical simulations were combined to study the potential of the parallel full hybrid electric vehicle (P2-FHEV) and mild hybrid vehicle (MHEV) to obtain lower fuel consumption and NOx emissions than a conventional powertrain in the Worldwide Harmonized Light Vehicles Cycle (WLTC). The hybrid vehicles are simulated with both CDC and diesel-gasoline RCCI combustion engines as power source. Each powertrain was optimized in terms of components (battery, electric motors...) capacity, internal combustion engine operative points, energy management strategy and gear ratios. The results show a significant fuel consumption reduction as the complexity of the hybrid system increases. The parallel architecture, which represents the most complex hybrid system tested in this work, allows obtaining a fuel consumption reduction of around 20% as compared to CDC. The dual-mode CDC-RCCI concept showed improvements in NOx and soot emissions with comparable values in terms of energy consumption and CO2 emissions than CDC. Additionally, the mild hybrid technology with the functionality of start-stop, torque assist and regenerative braking showed an acceptable balance between complexity and fuel consumption gain., The authors want to express their gratitude to General Motors Global Research & Development for providing the engine used to acquire the experimental data used in this investigation. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigation (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Potential of a Two-Stage Variable Compression Ratio Downsized Spark Ignition Engine for Passenger Cars under different driving conditions

  • López, J. Javier|||0000-0002-9486-2511
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Vielmo-Cogo, Vitor
  • Wittek, Karsten
[EN] With the aim of reducing pollutant emissions from internal combustion engines (ICE), the application of stoichiometrically operated spark ignition (SI) engines, for light-duty vehicles, has been overcoming the compression ignition (CI) engines market share throughout the past years. The ability of a substantial reduction of the primary harmful emissions (HC, CO, and NOx) through the use of the simple three-way catalyst (TWC) is the main reason for that. Nonetheless, with increasing attention to CO2 emissions, the development of highly efficient downsized SI engines turn to be of enormous interest. The synergies of multiple systems such as direct injection, turbocharger, and variable valve actuation are able to lead the SI efficiencies closer to those of CI engines. However, to enable high load operation on such downsized engines, the compression ratio (CR) must be reduced due to knock limitations, reducing the partial-load operations efficiency. The implementation of two-stage variable compression ratio (VCR) systems enables the extraction of high thermal efficiency with high CR at lower loads and extended knock-free high load operation with low CR. In this study, the evaluation of a two-stage VCR system applied to a state-of-the-art downsized SI engine was made through standard driving cycle simulations. The VCR mechanism is composed of an eccentric element in the small end of the connecting rod, which is rotated to increase/decrease the effective connecting rod length, achieving the CRs of 12.11:1 and 9.56:1. The engine was run in an eddy-current dynamometer test bench throughout the essential operating range to obtain the brake specific fuel consumption (BSFC) map. The VCR mechanism CR switching delay was also experimentally characterized to derive a function of the operating conditions. The measured map was entered into the map-based driving cycle simulation with a sub-model to account for the isolated effects of the transient period encompassing the compression ratio switching. The results show that slow CR transitions lead to fuel consumption penalties, which suggests the need for optimizing the control strategies of the VCR system. Even though this penalty, once the gear up-shift speed is optimized for each driving cycle, the VCR system still enables fuel consumption reductions up to 3% on the WLTC driving cycle, up to 4% on the proposed urban driving cycles and up to 3% on highway driving cycles with respect to the fixed CR., This research has been partially funded by FEDER and the Spanish Government through project RTI2018-102025-B-I00. The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Lnvestigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Emissions reduction from passenger cars with RCCI plug-in hybrid electric vehicle technology

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
[EN] Hybrid Electric Vehicles (HEVs) can be considered as a potential technology to promote the change from conventional mobility to e-mobility. However, the real benefits in terms of CO2 emissions depend on a great extent on their mode of use, vehicle design and electricity source. On the other hand, in the last few years, advanced combustion modes as Reactivity Controlled Compression Ignition (RCCI) showed great advantages in terms of NOx and soot emissions reduction. This paper has the purpose of assessing, through numerical simulations fed with experimental results, the potential of different hybrid vehicles when used together with a low temperature combustion mode. In particular, the dual-fuel Mild (MHEV), Full (FHEV) and Plug-in (PHEV) hybrid electric vehicles are tested and compared to the original equipment manufacturer (OEM) and the conventional dual-fuel powertrain, both no-Hybrid vehicles. The powertrains are optimized to meet the current European homologation legislation Worldwide Harmonized Light Vehicle Test Procedure (WLTP). After that, a deep analysis is performed in terms of performance and emissions. Lastly, a life-cycle analysis (LCA) is performed to evaluate the real potential of the different technologies. The results show that the PHEV has the highest benefits in terms of fuel consumption and engine-out emissions. With this technology, it is possible to achieve the 50 g/km CO2 target for the PHEVs with a medium battery size (15 kWh), while NOx and soot levels are under the Euro 6 limits. In addition, the RCCI technology shows great benefits to achieve the Euro 6 soot level for the other hybrid platforms. The LCA shows that the PHEVs can achieve 12% reduction of the total CO2 with respect to the FHEVs, and 30% with respect to the no-hybrid diesel platform., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Effects of fuel injection parameters on premixed charge compression ignition combustion and emission characteristics in a medium-duty compression ignition diesel engine

  • Molina, Santiago|||0000-0001-7879-2421
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
[EN] From the different power plants, the compression ignition diesel engines are considered the best alternative to be used in the transport sector due to its high efficiency. However, the current emission standards impose drastic reductions for the main pollutants, that is, NOx and soot, emitted by this type of engines. To accomplish with these restrictions, alternative combustion concepts as the premixed charge compression ignition are being investigated nowadays. The objective of this work is to evaluate the impact of different fuel injection strategies on the combustion performance and engine-out emissions of the premixed charge compression ignition combustion regime. For that, experimental measurements were carried out in a single-cylinder medium-duty compression ignition diesel engine at low-load operation. Different engine parameters as the injection pattern timing, main injection timing and main injection fuel quantity were sweep. The best injection strategy was determined by means of a methodology based on the evaluation of a merit function. The results suggest that the best injection strategy for the low-load premixed charge compression ignition operating condition investigated implies using a high injection pressure and a triple-injection event with a delayed main injection with almost 15% of the total fuel mass injected., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This investigation has been funded by VOLVO Group Trucks Technology. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Potential of using OMEx as substitute of diesel in the dual-fuel combustion mode to reduce the global CO2 emissions

  • Benajes, Jesús|||0000-0002-1653-9188
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
[EN] To achieve the targets of extreme low emissions values for the transport sector, several technologies emerged in the last few years. In this sense, advanced combustion modes as the dual-fuel low temperature combustion showed great advantages in terms of NOx and soot emissions reduction. At low and medium engine load, the operation is stable with virtually zero emissions. However, the exhaust gas recirculation rates at high load need to be increased to avoid excessive in-cylinder peaks, which leads to higher soot emissions. At these conditions, the use of non-sooting fuels as the oxymethylene dimethyl ethers (OMEx) allows avoiding the NOx-soot trade-off. In addition, the e-fuel consideration of the OMEx makes it suitable to reduce the global GHG emissions. This paper assesses the potential of using OMEx as high reactivity fuel to reduce the CO2 well-to-wheel emissions, and NOx and soot tailpipe emissions, in a medium-duty truck operating under dual-fuel combustion in transient conditions. The cargo mass was varied between 0% and 100% (18 ton) in the World Harmonized Vehicle Cycle. The tank-to-wheel analysis shows slightly higher CO2 production with OMEx-gasoline than with diesel-gasoline due to the ratio between the lower heating value and the carbon content. However, the well-to-wheel analysis shows the benefits of using OMEx to reduce the carbon dioxide footprint, which ranges from 13% (at full cargo mass) to 19% (at low cargo mass) compared to diesel-gasoline dual-fuel mode. This benefit is due to the large gains in terms of fuel production due to the carbon capture and the clean electric energy source necessary to produce the OMEx., The authors acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politècnica de València for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigación (SP20180148)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Octane number influence on combustion and performance parameters in a Dual-Mode Dual-Fuel engine

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
  • Lago-Sari, Rafael
[EN] Low temperature combustion stands as a promising alternative to realize low soot and NOx emissions while achieving fuel consumption benefits compared to the conventional diesel combustion. Nonetheless, its applicability is limited to narrow zones inside the engine map, reducing the potential benefits on a real driving case. In this scenario, the use of dual-mode dual-fuel combustion stands as an alternative to cover engine conditions up to full load, avoiding the constraints of the fully premixed combustion whenever is needed. This combustion concept is strongly influenced by the characteristics of the fuels that are used to create the charge stratification during the engine operation. The current research aims to evaluate the influence of the low reactivity fuel octane number on the combustion process and the average performance and emissions results. Additionally, the best octane number was determined by means of a merit function evaluation. Octane values of 100, 92.5, 87.5, 85 and 80 were obtained by blending iso-octane and heptane. Their performance was assessed in a medium-duty multi-cylinder platform at different representative operating conditions. The results suggest that fuels with octane number lower than 92.5 have a low impact at low load conditions. However, as load is increased, the high reactivity of the low research octane number fuels leads to early combustion processes, demanding settings modifications to avoid the appearance of excessive pressure gradients. As a consequence of these modifications, the fuel consumption and soot emissions increase. In general, RONs from 92.5 to 87.5 are less penalized, presenting the best merit function values, and therefore being the best fuels to be used in the hardware under investigation., The authors thanks VOLVO Group Trucks Technology and ARAMCO Overseas Company for supporting this research. The authors also acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politècnica de València for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigación (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

OMEx-diesel blends as high reactivity fuel for ultra-low NOx and soot emissions in the dual-mode dual-fuel combustion strategy

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Gil, A.|||0000-0001-7192-6992
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Lago-Sari, Rafael
[EN] Previous works demonstrated that the use of Oxymethylene ether (OMEx) in advanced combustion modes, as the dual-mode dual-fuel combustion, leads to a notable reduction of the lifecycle CO2 emissions while promoting lower NOx and soot emissions than those from conventional diesel combustion. Nonetheless, the low heating value of OMEx results in a fuel consumption increase. A possible solution to avoid this drawback is by blending OMEx with diesel fuel. This will help to introduce the OMEx in the market with minimum changes in the infrastructure. In this context, this work evaluates the impact of using OMEx-diesel blends in different mass percentages (50% and 70% of OMEx in diesel), compared to the reference net fuels (net diesel and OMEx) in a multi-cylinder compression ignition engine operating under dual-mode dual-fuel combustion at different engine loads (25%, 50%, 80% and 100%) and 1800 rpm. At each condition, an air mass sweep was performed to assess the limiting operating conditions with each fuel due to either excessive pressure gradients and soot production, or low combustion efficiency. The results suggested that the OMEx-diesel blends allow to reduce the soot emissions compared to net diesel for all the conditions tested. In addition, blends having an OMEx mass content greater than 70% allowed to fulfill the EUVI limits for NOx with ultra-low soot levels (< 0.01 g/kWh) up to 80% engine load. Nonetheless, the unique fuel able to achieve the EUVI limit for NOx with zero soot emissions simultaneously at 100% of engine load was found to be the pure OMEx., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18). The author R. Sari acknowledges the financial support from the Spanish ministry of science innovation and universities under the grant "Ayudas para contratos predoctorales para la formacion de doctors" (PRE2018-085043).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Potential of e-Fischer Tropsch diesel and oxymethyl-ether (OMEx) as fuels for the dual-mode dual-fuel concept

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
  • Lago-Sari, Rafael
  • Gordillo Zavaleta, Victor
  • Gaillard, Patrick
[EN] The dual-mode dual-fuel combustion strategy allows operating over the entire engine map by implementing a diffusive dual-fuel combustion at high engine loads. This requires increasing the amount of exhaust gas re-circulation to control the NOx emissions, which penalizes the soot levels. At these conditions, the use of nonsooting fuels as the e-Fischer Tropsch Diesel (e-FT) and oxymethylene dimethyl ethers (OMEx) could be a potential way to avoid the NOx-soot trade-off. The experimental results acquired in a compression ignition multi-cylinder medium-duty engine evidence that the higher oxygen content of OMEx allows reducing the soot emissions at high loads to near zero levels, while e-FT promotes a soot reduction of around 20% as compared to diesel. Nonetheless, the low lower heating value of OMEx leads to excessive injection durations, enlarging the combustion process and increasing the fuel consumption around 1.3-7.2% and 1.4-5.3% as compared to diesel and e-FT, respectively, depending on the engine load. Finally, the well to wheel analysis confirms the potential in reducing the carbon dioxide footprint of OMEx (14.8-69%) and e-FT (0.3-38.5%) compared to diesel, as they can be synthetized via direct air capture as a source of carbon and using renewable energy., The authors thanks VOLVO Group Trucks Technology and Aramco Overseas Company for supporting this research. The authors also acknowledge FEDER and the Spanish Ministerio de Economia y Competitividad for partially supporting this research through the TRANCO project (TRA2017-87694-R), and the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Dual fuel combustion and hybrid electric powertrains as potential solution to achieve 2025 emissions targets in medium duty trucks sector

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
  • Gaillard, Patrick
  • Poussin, Olivier
  • Amer, Amer A.
[EN] The European commission is targeting a 15% reduction in CO2 emissions for medium and heavy-duty transportation starting in 2025. Moreover, the next European normative (EU VII) will impose a decrease of 50% for NOx and particulate matter emissions with respect to the current EUVI normative. Meeting these requirements pose a significant challenge to truck and bus manufacturers. Several proposals appeared in the last few years as improve the cabin aerodynamics, decrease the friction losses and improve the powertrain efficiency. The last point involves improving the current combustion systems as well as the transmission and energy management. This work proposes to couple two potential technologies to reduce at the same time the global (CO2) and local pollution (NOx and soot). For this, two truck platforms representative of medium-duty applications (18 ton and 25 ton) are tested using the reactivity controlled compression ignition (RCCI) combustion mode with diesel and gasoline as fuels. In addition, the trucks are electrified to full hybrid technology in a parallel pre-transmission (P2) architecture. A 0D vehicle numerical model is used to evaluate the trucks under four different driving cycles representative of homologation and real driving conditions. The numerical model is validated against on road measurements. The RCCI combustion is modeled by means of a map-based approach with 54 points measured in steady-state conditions. This work presents a complete engine map calibration with measurements up to 350 hp using two combustion modes inside the map (so-called dual-mode dual-fuel). As a baseline, the commercial diesel no-hybrid trucks and the dual-fuel no-hybrid trucks are used. The results show the potential of the dual-mode dual-fuel combustion to achieve ultra-low NOx and soot emissions. In addition, the CO2 target reduction is achieved for several truck platforms and driving conditions due to the hybridization of the driveline. The cycles with large phases of urban driving are the most favorable due to the ability of recovering energy by means of the regenerative braking system and the possibility to avoid large idling phases with respect to the no-hybrid versions. In addition, the decrease of the payload improves the CO2 reduction with respect to the baseline cases., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Polit`ecnica de Val`encia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Exploration of suitable injector configuration for dual-mode dual-fuel engine with diesel and OMEx as high reactivity fuels

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Fogué-Robles, Álvaro
[EN] Dual-mode dual-fuel (DMDF) combustion stands over other low temperature combustion strategies as it is able to operate over the entire engine map by transitioning between reactivity controlled compression ignition and diffusive combustion depending on the engine load. In combination with non-sooting e-fuels, it is able to achieve low NOx and soot levels even at high loads. Oxygenated fuels like poly-oxymethylene dimethyl ethers (OMEx) have been already proved to present an outstanding NOx-Soot trade-off improvement when used in combination with a DMDF combustion strategy. One drawback of OMEx is that, despite having a high reactivity, it has a low lower heating value, which requires considerably longer injection events compared to other traditional fuels in order to achieve the same engine power output. The long injections limit the flexibility of the injection strategy and result in extremely long combustion durations. A possible solution to this problem resides in moving towards injectors with higher flow rate capacities, but this may compromise the mixing and combustion processes. This work aims to shed some light on the implications of changing the engine hardware to overcome this limitation by testing a DMDF mull-cylinder engine using gasoline as the low-reactivity fuel and diesel or OMEx as the high reactivity fuels with injectors of different flow capacity. The results show that a concise analysis of the involved phenomenology of the combustion process allows to find out the trade-off between the engine-out emissions and the mixing capacity of the injection system while the engine performance is not significantly affected., The authors thanks VOLVO Group Trucks Technology and ARAMCO Overseas Company for supporting this research. The authors also acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R) and the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (PAID-06-18).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Potential of hybrid powertrains in a variable compression ratio downsized turbocharged VVA Spark Ignition engine

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Martínez-Boggio, Santiago Daniel
  • Wittek, Karsten
[EN] After the diesel emissions scandal, also known as Dieselgate, Direct Injection Spark-Ignited (DISI) internal combustion engines (ICE) appears as the most promising alternative to mitigate the harmful tailpipe emissions from passenger cars. In spite of that, the current ICE technologies are not enough to achieve the fuel consumption/CO2 emissions targets set by the new transportation legislation (4.1 L-gasoline/100 km, 95 gCO(2)/km for 2021). In this complex scenario, the electrification of the powertrain using high efficiency electric motors and battery package together with sophisticated DISI engines appears as potential solution to meet these requirements. The aim of this work is to study the fuel consumption and pollutant emissions in transient conditions from a passenger car equipped with a variable compression ratio (VCR) DISI engine and electrified powertrain technologies. The vehicle behavior was simulated by means of a 0D GT-Suite model fed by experimental results obtained in an engine test bench. Mild hybrid electric vehicle (MHEV) and full hybrid electric vehicle (FHEV) architectures using a VCR DISI engine were studied. Moreover, an optimization methodology is presented to select the best vehicle configuration in terms of hardware and control strategies by means of a design of experiments (DoE). The results show that VCR allows a fuel improvement of 3% with respect to the conventional DISI fixed CR along the worldwide harmonized light vehicles test cycles (WLTC). The benefits found when combining the VCR technology with hybrid powertrains are even higher. In this sense, the fuel improvements were higher as the electrification levels increased, with 8% for MHEV-VCR and around 20% for FHEV-VCR. In terms of emissions, the two clear benefits with FHEV-VCR were the reduction of particle number (PN) and unburned hydrocarbons (HC) of around 60% and 15%, respectively, as compared to the conventional DISI., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R). The authors also acknowledge the Universitat Politecnica de Valencia for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigacion (SP20180148).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Fuel sensitivity effects on dual-mode dual-fuel combustion operation for different octane numbers

  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Villalta-Lara, David
  • Lago-Sari, Rafael
[EN] The dual-mode dual-fuel combustion is a promising combustion concept to achieve the required emissions and carbon dioxide reductions imposed by the next emissions standards. Nonetheless, since the combustion concept relies on the reactivity of two different fuels (diesel and gasoline), the fuel formulation requirements are stricter. This work investigates the effects of the low reactivity fuel sensitivity for different octane numbers at different operating conditions representative of the combustion regimes found inside the dual-mode dual-fuel engine map. For this, experimental evaluations were performed using fuels with research octane number 92.5 and 80 and different sensitivities (0, 5 and the maximum one achievable for each fuel). The combustion development was assessed by means of the heat release rate characterization. Moreover, numerical simulations in a constant volume homogeneous reactor were used to explore and understand the impact of the different fuels on the ignition delay time. The results suggest that the sensitivity increase affects the different research octane number fuels in a different way. For the fuel with research octane number 92.5, the sensitivity variation increases the experimental ignition delay, impairing the combustion process and increasing the fuel consumption. In the case of the fuel with research octane number 80, the sensitivity increase does not affect the combustion development. This was justified by the numerical investigation, which points to a wider temperature range where the sensitivity does not affect the final ignition delay for research octane number 80. Moreover, generally, the ignition delay times for research octane number 80 considering the experimental gasoline fraction used are half than those of research octane number 92.5. At full load conditions, the trend is inverted, where the experimental ignition delay for research octane number 80 is affected by the sensitivity whilst research octane number 92.5 presents only modifications after the combustion start., The authors thanks ARAMCO Overseas Company and VOLVO Group Trucks Technology for supporting this research. The authors also acknowledge FEDER and Spanish Ministerio de Economía y Competitividad for partially supporting this research through TRANCO project (TRA2017-87694-R), and the Universitat Politècnica de València for partially supporting this research through Convocatoria de ayudas a Primeros Proyectos de Investigación (PAID-06-18).