Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Biogas upgrading by intensified methanation (SESaR): Reaction plus water adsorption - desorption cycles with Ni-Fe/Al2O3 catalyst and LTA 5A zeolite

  • Mercader, Víctor Daniel
  • Durán, Paúl
  • Aragüés-Aldea, Pablo
  • Francés, Eva
  • Herguido, Javier
  • Peña, José Angel
This work is conducted within the framework of the Power to Gas (PtG) technologies, focusing on the topic of “biogas upgrading”. The objective is to enhance the CH4 content of biogas streams by utilizing the CO2 present in these streams through the Sabatier reaction, thereby producing a renewable alternative to natural (fossil) gas. Referred to as “SESaR”(Sorption Enhanced Sabatier Reaction), this process employs a catalytic fixed-bed reactor, featuring selective water adsorption using LTA 5A zeolites, as an innovative approach to traditional methanation reactors. The catalyst used comprises Ni-Fe (7.5:2.5 wt/wt) as the active metallic phase supported on γ-Al2O3. Experimental work has been divided in two sets of trials. The first set focuses on the hydrogenation of CO2 as single reactant (H2 also supplied in the inlet with 4:1 = H2:CO2 molar ratio). The second set of experiments was carried out with a synthetic gas mixture representative of a sweetened biogas stream (molar ratio CH4:CO2 = 7:3). Maximum intensification behavior for CO2 conversion was found at 350 °C, also showing that CH4 presence in the inlet gas has negligible influence on the conversion of CO2. Selectivity to CO is minimized at temperatures exceeding 300 °C and remains constant after three consecutive cycles of methanation, water adsorption, and desorption. The Fe-Ni catalyst has demonstrated sustained performance throughout the experimental cycles, exhibiting no significant loss of activity.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Biogas upgrading through CO2 methanation in a polytropic - distributed feed fixed bed reactor

  • Durán, P.
  • Aragüés-Aldea, P.
  • González-Pizarro, R.
  • Mercader, V. D.
  • Cazaña, F.
  • Francés, E.
  • Peña, J. A.
  • Herguido, J.
Methanation of the CO2 contained in a biogas stream has been experimentally analyzed in a fixed bed reactor with a Ni-Mn catalyst, evaluating the effect of feeding reactants distributed throughout the bed. The performance of different feeding configurations (conventional cofeeding and others implying a lateral distribution of one of the reactive streams) has been analyzed for different nominal temperatures T (250–400 ºC) and weight-related space velocities WHSV (47.71–6.63 gCO2 gcat-1 h-1), always keeping a H2: CO2 ratio of 4:1, and a CH4:CO2 ratio of 7:3. For identical WHSV, the lateral biogas distribution (Poly-Biogas feeding configuration) always showed the best results in terms of activity (higher conversion at the same temperature) and selectivity (lower selectivity to CO in iso-conversion). These better results agree with what was observed in a previous work in methanation of CO2 (i.e., without methane in the feed). In that work, CO2 was distributed along the catalytic bed by several lateral feeds (Poly-CO2). When T was kept constant and WHSV was varied, the reactor fed with distributed biogas (Poly-Biogas), again confirmed its higher efficiency and better selectivity for biogas upgrading (i.e., higher CH4 content). Furthermore, by adopting a Poly-Biogas (or poly-CO2) feeding configuration, a more homogeneous temperature profile was achieved along the bed avoiding the severity of hot spots appearance. In contrast, the lateral distribution of hydrogen (Poly-H2) always led to similar or worse results than those for the conventional co-feeding configuration.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Enhanced methanation assisted by CO2 adsorption on a bimetallic catalytic fixed bed reactor

  • Mercader Plou, Víctor Daniel
  • Sanz-Monreal, Pablo
  • Durán, Paul
  • Aragüés-Aldea, Pablo
  • Francés, Eva
  • Peña, José Ángel
  • Herguido, Javier
This work studies the influence of introducing a CO2 adsorbent in a bimetallic catalytic fixed bed reactor. The catalyst is a lab-made Fe-Ni alloy (2.5:7.5% wt/wt) supported on gamma alumina. Two CO2 adsorbents were tested in this study, a lab made CaO and a Na2O (10% wt/wt) supported on gamma alumina.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

A preliminary assessment of sorption-enhanced methanol synthesis in a fluidized bed reactor with selective addition/removal of the sorbent

  • Menéndez, Miguel
  • Ciércoles, Raúl
  • Lasobras, Javier
  • Soler, Jaime
  • Herguido, Javier
Methanol synthesis from CO2 can be made in the presence of a sorbent to increase the achievable yield. If the fresh sorbent is continuously fed to a fluidized bed and separated from the catalyst bed by segregation, a steady-state operation can be achieved. The objective of the present work is to provide insight on the suitable operating conditions for such a fluidized bed reactor system. For this, a conventional CuO/ZnO/Al2O3 was selected as the catalyst, and the SiOLITE® zeolite was selected as the sorbent. Different particle sizes were used to be tested in various proportions to perform the fluidized bed segregation study. The fluid dynamics and segregation of the catalyst–sorbent binary mixtures were the most critical points in the development of this proof of concept. A good bed segregation with a mixing index of 0.31 was achieved. This fact favors the correct operation of the system with the continuous addition of adsorbent, which had hardly any catalyst losses during the tests carried out, achieving a loss of 0.005 g/min under optimal conditions. Continuous feeding and removal of sorbent with a low loss of catalyst was observed. Reactor simulations with MATLAB provided promising results, indicating that the addition of sorbent considerably improves the methanol yield under some operating conditions. This makes it more viable for industrial scaling, since it allows us to considerably reduce the pressure used in the methanol synthesis process or to increase the yield per step, reducing the recirculation of unconverted reactants.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Biogas upgrading through CO2 methanation in a multiple-inlet fixed bed reactor: Simulated parametric analysis

  • Aragüés-Aldea, P.
  • Mercader, V. D.
  • Durán, P.
  • Francés, E.
  • Peña, J. A.
  • Herguido, J.
A simulation of the catalytic CO2 methanation reaction was carried out, evaluating the effect of reactants distributed feeding throughout the bed. The main operational parameters were studied in a multiple-inlet reactor to test their effect on conversions and, most importantly, on selectivities towards both CO and CH4 as reaction products. The analyzed parameters were, firstly, the number of feeding points (N) and the dosage degree of reactants, followed by temperature (T), partial pressures of reactants (H2:CO2 ratios), and the composition of a sweetened biogas as feeding stream (CH4:CO2 ratios). It is confirmed that a distribution of biogas through several side inlets improves selectivities to the desired CH4 product, over other feeding configurations. The effect of distributing reactants becomes intensified when the number of lateral feedings increases. This observation supports the experimental trends already proven in previous works. Regarding main operation parameters such as temperature and H2:CO2 molar ratio, the analysis confirmed that their influence on selectivities acts just as predicted at low conversions. However, when these conversions become higher the space velocity (WHSV) is the most important factor for selectivities. Finally, no significant changes in reaction performance were obtained when modifying the biogas CH4:CO2 ratio in the broad range of methane concentrations from 55 v% to 70 v%.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Effect of particles size and density on the segregation of catalyst-sorbent mixtures for direct sorption-enhanced DME synthesis: Experimental and mathematical study

  • Renda, Simona
  • Soler, Jaime
  • Herguido, Javier
  • Menéndez, Miguel
Direct sorption-enhanced dimethyl ether synthesis (SEDMES) is a promising process for the production of fuels from CO2 sources. Using novel technologies, the process can be run exploiting the phenomena of particles segregation in a fluidized bed reactor. However, the knowledge on the solid movement and the segregation patterns is a mandatory preliminary step for the setup of the final application. In this study, we evaluated the impact of particles size and density on the segregation patterns, and we used the Gibilaro and Rowe (GR) model to analytically represent the experimental results. It was observed that the variation of both parameters influences segregation, even though a higher separation degree in a wider operating velocity range was observed when a higher density ratio was induced between the two solids. Through the experimental analysis, five possible bed configurations were identified, and a consideration was made on the aims of the GR model to adjust the mathematical representation to the present case. By considering the bottom portion of the bed as a jetsam-rich phase and not – as previously reported – as a segregated layer, a mass balance on the catalyst allowed to obtain a faithful analytical representation of the experimental segregation patterns.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Optimizing Sorption Enhanced Methanation (SEM) of CO2 with Ni3Fe + LTA 5 A mixtures

  • Mercader, V.D.
  • Aragüés-Aldea, P.
  • Durán, P.
  • Francés, E.
  • Herguido, J.
  • Peña, J.A.
This study investigates the integration of catalytic CO2 methanation and water adsorption using a Ni-Fe-based catalyst and LTA 5 A zeolite to enhance methane production via the Sabatier reaction. By mitigating thermodynamic limitations through in situ water removal, the research explores key operational parameters, including temperature, space velocity, and H₂:CO₂ feed ratios, to optimize process performance. The findings highlight that a temperature of 300 °C, a WHSV of 1.50 × 104 (STP) mL·gcat−1·h−1 (4.86 gCO2·gcat⁻¹·h⁻¹), and a H₂:CO₂ molar ratio equal to 5:1, result in enhanced methane yields, shifting thermodynamic equilibrium due to water sorption during initial stages. The presence of methane in the feed, representative of a biogas, demonstrated negligible effects on methane yields under optimal conditions, underscoring the method’s feasibility for direct biogas upgrading. While the process achieved significant intensification, challenges such as loss of activity of the bed of solids (catalyst plus water adsorbent) were identified, necessitating further advancements in both catalyst and adsorbent stability, as well as a deeper study on their interaction. The study provides a pathway for scaling up adsorption-enhanced methanation technologies to achieve renewable methane production, addressing the dual goals of carbon management and energy storage.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Techno-economic assessment of a plant for the upgrading of MSW biogas to synthetic natural gas by thermocatalytic methanation

  • Sanz-Monreal, P.
  • Mercader, V.D.
  • Aragüés-Aldea, P.
  • Durán, P.
  • Francés, E.
  • Herguido, J.
  • Peña, J.A.
This study evaluates the techno-economic feasibility of a plant designed to produce synthetic natural gas (SNG) from biogas through direct catalytic methanation. The proposed facility is simulated with Aspen Plus® v14, using a comprehensive approach that covers the entire process, from biogas pretreatment to the production of the final product. The installation aims to contribute to the development of Power-to-Gas (Power-to-Methane) strategy for decarbonization. The plant, to be located in northeastern Spain, operates at an industrial scale with a production capacity of approximately 1100 Nm3/h of SNG, obtained from a 1425 Nm3/h biogas plant. The process includes five main stages to meet Spanish gas quality standards for grid injection: desulfurization, using amines for sulfur removal; electrolysis, for the generation of renewable hydrogen; thermocatalytic methanation, which combines CO2 from the biogas with hydrogen to enrich the methane content; dehydration, to meet SNG moisture specifications; and cogeneration, intended for the joint production of electricity and steam to meet the plant's energy demands. A detailed analysis of investment costs (CAPEX) and operational expenses (OPEX) is conducted, identifying the key factors influencing the project's profitability. The economic assessment indicates a total capital investment of 21.83 M€ and operational expenses nearly 8 M€ annually. The profitability threshold for the base scenario is estimated at 91.75 €/MWh, exceeding the 2023 natural gas market average in the Iberic peninsula (39.11 €/MWh), highlighting the current economic challenges of SNG production.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Catalytic CO2 methanation for biogas upgrading using a polytropic fixed bed reactor

  • Aragüés-Aldea, P.
  • Pizarro, R.G.
  • Durán, P.
  • Mercader, V.D.
  • Francés, E.
  • Peña, J.A.
  • Herguido, J.
The experiments of this study aim to determine the effect of distributed feeding of reactants throughout the many inlets of a polytropic fixed bed reactor. The effect of dosing either carbon dioxide or hydrogen, was analyzed on the Sabatier reaction (i.e., carbon dioxide methanation) using a Ni-Mn catalyst to carry out the biogas upgrading process. This work analyzes the influence of three feeding configurations (a conventional fixed bed, one with side distribution of biogas, and another with side distribution of hydrogen) and temperatures (350, 375, and 400 °C) for a wide gas hourly space velocity (GHSV) range from 30 × 103 (STP) mL gcat−1 h−1 to more than 200 × 103 (STP) mL gcat−1 h−1. The molar ratios of reactants were always kept constant (H2:CH4:CO2 = 12:7:3) simulating the hydrogenation of the CO2 present in a biogas with a proportion of 70 v% of CH4 and 30 v% of CO2. The empirical results highlight that side distribution of biogas yields improved results over those obtained in a conventional fixed bed reactor, or the one with side distribution of hydrogen. At temperatures of 375 and 400 °C, this feeding configuration brings higher conversions than the other two, while consistently shows greater selectivities to methane for all the conditions tested. As such, its optimal condition to conduct the process is extended to methane space-time yields (STY), for which the highest methane productions are obtained. In addition, the influence of contact time, or GHSV, was determined to be critical both on selectivities and flowrates of methane. It is shown that for a given conversion value, keeping constant all the other parameters, a longer contact time and lower temperature result in an improvement of selectivities to methane. On the other hand, it also affects STY values, where an optimum between the employed flows of reactants and reaction performances is reached at a value of 180 × 103 (STP) mL gcat−1 h−1, independently of experimental conditions
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Influence of Ni-Fe load in a bimetallic catalyst supported on Zeolite 13X for CO2 methanation in a fixed bed reactor

  • Mercader Plou, Víctor Daniel
  • Ruiz-Alejos, David
  • De Jong, Wiebren
  • Durán, Paul
  • Aragüés Aldea, Pablo
  • Sanz Monreal, Pablo
  • Becerril, Miguel Ángel
  • Francés, Eva
  • Herguido, Javier
  • Peña, José Ángel
In this work three Ni-Fe catalysts supported on zeolite 13X were tested for CO2 methanation at different temperatures. The study shows the influence of the active species load on the synthesized catalysts. In addition, the effect of Ni-Fe ratio present on the catalysts was observed. 
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Modelado cinético para la metanación de CO2 sobre un catalizador Ni3Fe/Al2O3

  • Sanz Monreal, Pablo
  • Mercader Plou, Víctor
  • Durán Sánchez, Paúl
  • Francés Pérez, Eva
  • Herguido Huerta, Javier
  • Peña Llorente, José Ángel
Varios modelos cinéticos del tipo Langmuir-Hinshelwood han sido considerados para el ajuste experimental a la metanación de CO2. Los coeficientes de los mismos han sido determinados mediante Regresión-No-Lineal y, posteriormente, valorados desde un punto de vista estadístico y termodinámico.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Process Intensification for CO2 Hydrogenation to Liquid Fuels

  • Renda, Simona
  • Menéndez, Miguel
Liquid fuels obtained from CO2 and green hydrogen (i.e., e-fuels) are powerful tools for decarbonizing economy. Improvements provided by Process Intensification in the existing conventional reactors aim to decrease energy consumption, increase yield, and ensure more compact and safe processes. This review describes the advances in the production of methanol, dimethyl ether, and hydrocarbons by Fischer–Tropsch using different Process Intensification tools, mainly membrane reactors, sorption-enhanced reactors, and structured reactors. Due to the environmental interest, this review article focused on discussing methanol and dimethyl ether synthesis from CO2 + H2, which also represented the most innovative approach. The use of syngas (CO + H2) is generally preferred for the Fischer–Tropsch process; hence, studies examining this process were included in the present review. Both mathematical models and experimental results are discussed. Achievements in the improvement of catalytic reactor performance are described. Experimental results in membrane reactors show increased performance in e-fuels production compared to the conventional packed bed reactor. The combination of sorption and reaction also increases the single-pass conversion and yield, although this improvement is limited by the saturation capacity of the sorbent in most cases.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Intensifying synthetic natural gas production by functionalization of a NiFe/γ-Al2O3 catalyst with alkaline and alkaline-earth materials

  • Mercader, V.D.
  • Sanz-Monreal, P.
  • Durán, P.
  • Aragüés-Aldea, P.
  • Francés, E.
  • Herguido, J.
  • Peña, J.A.
This study demonstrates the influence of the functionalization method (Mechanical Mixture -MM- and Dual Function Materials -DFM-) of two CO2 adsorbent species (Na and Ca) in a catalytic fixed-bed reactor for CO2 methanation. The experiments consisted of cycles beginning with a CO2 adsorption stage followed by a methanation stage (with H2), interspersed with or without inert purge periods. The greatest enhancement in methane generation was observed in experiments with a mechanical mixture (MM) of NiFe/γ-Al2O3 catalyst and Na2O/γ-Al2O3. The methane production capacity was tested over a temperature range comprised between 200 and 400 °C, with values over 380 μmol/g obtained under moderate conditions (350 °C and pCO2 = 0.12 bar) and selectivity to methane close to 100 %. Since the ultimate goal is the methanation of the CO2 present in a biogas (without removing CH4), the potential effect of the presence of methane during the CO2 adsorption stages was also investigated. To achieve this task, a feed stream representative of a sweetened biogas coming from the anaerobic decomposition of municipal solid waste (MSW) (70 %v CH4 and 30 %v CO2) was used. The results showed no adverse effects along the successive cycles, paving the way to the use of these solids for biogas upgrading. On the other hand, the catalyst did not show a significant loss of activity after several hours of repetitive adsorption-methanation cycles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Tuning e-fuel selectivity in sorption-enhanced CO2 hydrogenation over In2O3/ZrO2: The effect of LTA and FAU zeolites

  • González-Pizarro, R.
  • Calero-Berrocal, R.
  • Lasobras, J.
  • Renda, S.
  • Rodríguez-Pardo, M.R.
  • Soler, J.
  • Menéndez, M.
  • Herguido, J.
The e-fuels synthesis via CO2 hydrogenation and the Sorption Enhanced Reaction technology are captivating strategies for CO2 utilization and the integration of renewable energy sources. This study focuses on enhancing the conversion of CO2 over an In2O3/ZrO2 catalyst by incorporating LTA zeolites (3A and 4A) and a FAU zeolite (13X). Key operational parameters, such as temperature (T), Gas Hour Space Velocity (GHSV), type of zeolite, and Zeolite: Catalyst mass ratio (Z/C), were systematically varied. LTA zeolites (3A and 4A) provided the highest CO2 conversions. The introduction of a water-adsorbing solid into the reactor significantly altered the products yield and selectivity. While the selectivity towards CH4, CH3OH, and C2H6O appeared to lay on the type of zeolite, the selectivity towards CO remained unaffected. Zeolite 3A demonstrated the greatest enhancement in selectivity towards CH4 and CH3OH, whereas the synthesis of C2H6O was favored by zeolites 4A and 13X. The Zeolite:Catalyst mass ratio also played a crucial role in process performance, influencing both CO2 conversion and product selectivity. Increasing this ratio improved CO2 conversion and reduced CO selectivity under all operating conditions, while CH4 selectivity increased. However, the selectivity toward CH3OH and C2H6O exhibited an anomalous and complementary behavior. While a maximum was observed for DME, a minimum was registered in methanol production, suggesting a dependency of the dehydration reaction kinetics on the amount of water produced during the reaction.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Low loading copper-based catalysts for effective CO2 hydrogenation to methanol

  • González-Pizarro, R.
  • Renda, S.
  • Lasobras, J.
  • Soler, J.
  • Menéndez, M.
  • Herguido, J.
Methanol synthesis via CO2 hydrogenation is an emerging Power-to-Liquid (PtL) technology aimed to accelerate the energy transition and the defossilization of key sectors, particularly maritime transport. This study focuses on the study of low loading formulations, to minimize the catalyst cost. Key operational variables including temperature (T), Weight Hourly Space Velocity (WHSV), copper and zinc loadings, and aging state were systematically varied. An overall active phase loading of 10 %wt emerged as optimal. Within this total loading, a 5 %wtCu-5 %wtZn/ZrO2 catalysts delivered higher methanol productivity than 10 %wtCu/ZrO2; however, the bimetallic catalysts showed pronounced deactivation under water-rich atmospheres, establishing 10 %wtCu/ZrO2 as the most promising catalysts. Operating temperature and WHSV exerted a strong, synergistic influence on CH3OH formation; in particular, increasing WHSV shifted the reaction away from thermodynamic control and boosted methanol synthesis. Finally, the catalytic performance of these low-loading catalysts was benchmarked against high-copper-loading methanol catalysts reported in the literature by critically compare their activities as a function of the residence time (τ) calculated at reaction conditions. This assessment revealed that the proposed formulation is highly competitive when compared to most conventional formulation, with a maximum methanol space time yield (STYCH3OH) of 3.9 gCH3OH gCu-1 h-1. This comparison confirms that the catalysts proposed in this study could offer a remarkably more efficient use of the active phase than the conventional high-copper-loading catalysts.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Packed-bed membrane reactors as a strategy for selective CO2 methanation

  • Aragüés-Aldea, P.
  • Durán, P.
  • Mercader, V.D.
  • Renda, S.
  • Francés, E.
  • Peña, J.A.
  • Herguido, J.
CO2 methanation represents a key route within Power-to-X strategies for converting captured carbon into synthetic natural gas. However, its efficiency is limited by thermodynamic constraints, heat management issues, and undesired CO formation due to the reverse water–gas shift reaction. In this work, a novel packed-bed membrane reactor (PBMR), conceived as an evolution of the polytropic packed-bed reactor (PPBR), is proposed and experimentally validated for selective CO2 methanation. The reactor enables distributed reactant feeding through a porous membrane wall, allowing enhanced control over local reaction environments along the catalytic bed. A Ni–Fe/Al2O3 catalyst was employed and tested under various operating conditions, including different weight hourly space velocities (WHSV) and feeding configurations (conventional, co-current, and counter-current). The influence of distributing either H2 or CO2 was systematically investigated in terms of CO2 conversion, temperature profiles, and CO selectivity. While distributed configurations did not improve overall CO2 conversion compared to conventional operation, they significantly affected selectivity. In particular, CO2-distributed feeding consistently reduced CO selectivity under iso-conversion conditions, achieving up to a 40% decrease in the most favorable case. This significant reduction highlights the effectiveness of spatial reactant management in driving the reaction pathway toward methane. Overall, these results underline the critical role of reactor design in overcoming selectivity limitations and demonstrate the potential of membrane-assisted distributed feeding as a process intensification strategy for CO2 methanation.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Sorption Enhanced reverse Water Gas Shift (SErWGS): Optimal potassium-driven methanol suppression and zeolite type selection (LTA and FAU) under high-pressure conditions

  • González-Pizarro, R.
  • Renda, S.
  • Lasobras, J.
  • Soler, J.
  • Menéndez, M.
  • Herguido, J.
CO hydrogenation is thermodynamically and kinetically more favorable than direct CO2 hydrogenation, making a preceding CO2-to-CO conversion step an attractive route for enhancing e-fuel production. In this work, intensified e-syngas production via high-pressure CO2 hydrogenation was investigated through the Sorption-Enhanced Reverse Water-Gas Shift (SErWGS) process. Particular attention was given to methanol suppression through the incorporation of low potassium loadings in the catalyst, and to the influence of zeolite type on process performance. The effect of potassium loading on catalytic activity and CH3OH inhibition was systematically evaluated under different temperatures and WHSV values using a Design of Experiments (DoE) methodology, which enabled the development of empirical models describing the process behavior and identification of the optimal catalyst formulation. In parallel, the performance of different zeolite adsorbents was assessed to maximize H2O removal and process intensification. The optimized catalyst, containing 1.5 wt% K, effectively suppressed methanol formation while maximizing CO production. The intensified SErWGS process achieved CO yields exceeding the thermodynamic equilibrium limit at the operating temperature. H2/CO ratios approaching those expected for complete CO2-to-CO conversion, and pre-breakthrough periods accounting for up to 80% of the total cycle duration. The highest CO yield obtained in this work reached 42% at 260 °C using the 3A-LTA zeolite, corresponding to a value approximately 2.5 times higher than that achieved under conventional RWGS conditions. Remarkably, this CO yield was comparable to the thermodynamic equilibrium yield expected at approximately 450 °C in a conventional rWGS process. These results validate that the SErWGS strategy can deliver performance equivalent to operating nearly 200 °C above the actual reaction temperature, highlighting its potential as an effective intensification approach for low-temperature CO2 conversion and sustainable e-syngas production.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

LTA and FAU zeolites as water and CO₂ sorbents for sorption-enhanced CO₂ hydrogenation (SECO2H): Low-pressure sorption-enhanced methanol synthesis as a case study

  • González-Pizarro, R.
  • Mercader, V.D.
  • Durán, P.
  • Renda, S.
  • Soler, J.
  • Peña, J.A.
  • Menéndez, M.
  • Herguido, J.
The selection of the zeolite used in a sorption enhanced CO2 hydrogenation process (SECO2H) plays a decisive role in determining the extent of process intensification and the resulting product yields. This selection is governed by several key properties, including zeolite acidity, pore aperture, adsorption capacity, and the selective adsorption of the target reaction product. Among the zeolites investigated, namely 3 A, 4 A, 5 A (LTA framework), and 13X (FAU framework), the last one exhibited the highest CO2 and H2O adsorption capacities. However, LTA-3A provided the highest selectivity and affinity towards H2O adsorption. H2O adsorption also appeared stronger than CO2 adsorption, as complete H2O desorption and zeolite regeneration required more severe desorption conditions than those needed for CO2 removal. Sorption-enhanced methanol synthesis (SEMS) was selected as the target reaction to evaluate the effect of these zeolites on CO2 hydrogenation. Among all the materials studied, only LTA-3A provided a pronounced intensification of the process, increasing both CH3OH and CO yields due to its highly selective H2O adsorption. The SEMS experiments assisted by LTA-3A delivered yields above the conventional thermodynamic limits of the conventional process and outperformed reported values under comparatively mild operating conditions.