Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 6
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Design of Capacitively Loaded Coupled-Line Bandpass Filters With Compact Size and Spurious Suppression

  • Orellana, Marco
  • Selga, Jordi
  • Vélez, París
  • Sans, Marc
  • Rodríguez Pérez, Ana María
  • Bonache, Jordi
  • Martin, Ferran
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This paper is focused on the synthesis of capacitively loaded coupled lines for the design of bandpass filters with compact size and spurious suppression. The filters consist of cascaded pairs of coupled lines periodically loaded with patch capacitors. The loading capacitances provide a slow-wave effect to the coupled lines useful for filter miniaturization, whereas periodicity introduces bandgaps that can be controlled in order to achieve spurious suppression. Filter design is achieved following an automated process based on aggressive space mapping (ASM) optimization. The two reported examples, a third-order filter with central frequency f0=1.0 GHz, 8% fractional bandwidth, and 0.1-dB ripple level and a fifth-order filter with central frequency f0=1.8 GHz, 8% fractional bandwidth, and 0.1-dB ripple level, demonstrate the potential of the proposed ASM-based design approach, as well as the effectiveness of the loading capacitances to reduce filter size and reject the spurious bands. Significant size reduction in both filters is achieved, whereas the out-of-band rejection is better than 30 and 45 dB in the third-order and fifth-order filters, respectively, up to at least 4f0 ., This work was supported in part by MINECO-Spain under Project TEC2013-47037-C5-1-R, Project TEC2013-40600-R, and Project TEC2013-49221-EXP, in part by the Generalitat de Catalunya under Project 2014SGR-157, and in part by FEDER funds. The work of F. Martin was supported by the Institucio Catalana de Recerca i Estudis Avancats. The work of M. Orellana was supported in part by the Universidad de Costa Rica, in part by MICITT, and in part by CONICIT
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Automated design of bandpass filters based on open complementary split ring resonators (OCSRRs) using aggressive space mapping (ASM) optimization

  • Rodríguez Pérez, Ana María
  • Selga, Jordi
  • Sans, Marc
  • Martin, Ferran
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
[EN] This paper is focused on the design of bandpass filters based on open complementary split ring resonators (OCSRRs) in microstrip technology. The filters are obtained by coupling the corresponding shunt resonators (OCSRRs) through admittance inverters (quarter wavelength transmission line sections). Different undesirable effects derived from the chosen topology are taken into account and are compensated at the design level. These effects include the reduction in bandwidth (caused by the narrowband functionality of the line sections acting as admittance inverters), and the presence of a spurious band above the filter passband. The proposed technique is based on the well-known aggressive space mapping algorithm, which is a powerful tool for the synthesis and design of microwave components. The design of the OCSRR-based filter is provided in a fully automated way as the main result of this paper. Copyright (c) 2015 John Wiley & Sons, Ltd., This work has been supported by MINECO-Spain (projects TEC2010-17512 METATRANSFER, TEC2013-47037-C5-1-R, CONSOLIDER EMET CSD2008-00066, TEC2013-40600-R, and TEC2013-49221-EXP), Generalitat de Catalunya (project 2014SGR-157), and Institucio Catalana de Recerca i Estudis Avancats (who has awarded Ferran Martin).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Automated Design of Common-Mode Suppressed Balanced Wideband Bandpass Filters by Means of Aggressive Space Mapping

  • Sans, M.
  • Selga, J.
  • Velez, P.
  • Rodriguez Perez, Ana Maria
  • Bonache Albacete, Jordi
  • Martin, Ferran
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
The automated and unattended design of balanced microstrip wideband bandpass filters by means of aggressive space mapping (ASM) optimization is reported in this paper. The proposed filters are based on multisection mirrored stepped impedance resonators (SIRs) coupled through quarter-wavelength transmission lines, acting as admittance inverters., This work was supported by MINECO-Spain (projects TEC2013-47037-C5-1-R, TEC2013-40600-R, TEC2013-49221-EXP), Generalitat de Catalunya (project 2014SGR-157), Institucio Catalana de Recerca i Estudis Avancats (who awarded Ferran Martin), and by FEDER funds.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Automated design of balanced wideband bandpass filters based on mirrored stepped impedance resonators (SIRs) and interdigital capacitors

  • Sans, Marc
  • Selga, Jordi
  • Vélez, París
  • Rodriguez Perez, Ana Maria
  • Bonache, Jordi
  • Martin, Ferran
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
This paper presents small balanced bandpass filters exhibiting wide differential-mode pass bands and high common-mode suppression. The filters are implemented in microstrip technology and their topology consists of multisection mirrored stepped impedance resonators (SIRs) alternating with mirrored interdigital capacitors. The mirrored SIRs provide the required common-mode transmission zeros to achieve effective rejection of that mode in the region of interest, i.e. the differential-mode pass band. An automated design method for such filters, based on aggressive space mapping, is reported. The method uses the equivalent circuit model of both the mirrored SIRs and the interdigital capacitors, and filter synthesis is based on a quasi-Newton iterative algorithm where parameter extraction is the key aspect. The automated design approach is illustrated through an order-3 filter, where it is demonstrated that the filter topology is generated from the specifications. As compared with previous balanced filters based on mirrored SIRs coupled through admittance inverters, the proposed filters of this work are smaller and the design method is simplified, since bandwidth compensation due to the narrowband functionality of the inverters is avoided., This work was supported by MINECO-Spain (projects no. TEC2013-47037-C5-1-R, TEC2013-40600-R, and TEC2013-49221-EXP), Generalitat de Catalunya (project no. 2014SGR-157), and Institucio Catalana de Recerca i Estudis Avancats (who has awarded Ferran Martin).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Design of planar wideband bandpass filters from specifications using a two-step aggressive space mapping (ASM) optimization algorithm

  • Sans, Marc
  • Selga, Jordi
  • Rodríguez Pérez, Ana María
  • Bonache, Jordi
  • Martín, Ferran
  • Boria Esbert, Vicente Enrique|||0000-0001-7150-9785
This paper is focused on the automated and unattended optimization of a type of planar wideband bandpass filters by means of aggressive space mapping (ASM). The considered filters are microstrip filters implemented through a combination of shunt connected stepped impedance resonators (SIRs) and grounded stubs coupled through admittance inverters. The most relevant and novel aspect of this paper is the fact that the filter layout is automatically generated from filter specifications, i.e., central frequency, fractional bandwidth, in-band ripple and order, without the need of any external aid to the design process. To achieve this layout generation, filter optimization has been divided into two independent ASM processes. The first one generates the filter schematic (circuit element values) providing the required specifications. This first iterative process is necessary since, due to the narrow band operation of the admittance inverters, the target specifications are achieved by compensating the effects of such narrow band operation. The purpose of the second ASM algorithm is to automatically generate the layout from the filter schematic resulting from the first ASM process. To validate the new two-step ASM optimization tool, two sets of filter specifications (inputs of the developed tool), are considered. The generated filter layouts exhibit frequency responses that satisfy the specifications, and are in excellent agreement with the responses of the schematics., This work was supported by MINECO-Spain (projects TEC2010-17512 METATRANSFER, TEC2010-21520-C04-01 and TEC2013-47037-C5-1-R, CONSOLIDER EMET CSD2008-00066, TEC2013-40600-R and TEC2013-49221-EXP), Generalitat de Catalunya (project 2014SGR-157), and Institucio Catalana de Recerca i Estudis Avancats (who has awarded F. Martin). This paper was presented in part at the IEEE MTT-S International Microwave Symposium, Tampa Bay, FL, USA, June 1-6, 2014.
Dipòsit Digital de Documents de la UAB
Publicación Artículo científico (JournalArticle)

Synthesis of slow-wave structures based on capacitive-loaded lines through aggressive space mapping (ASM)

  • Orellana Gutiérrez, Marco Antonio
  • Selga Ruiz, Jordi|||0000-0002-1660-500X
  • Sans, Marc
  • Rodríguez, Ana
  • Boria, Vicente E.
  • Martín, Ferran|||0000-0002-1494-9167
This article is focused on the automated synthesis of slow-wave structures based on microstrip lines loaded with patch capacitors. Thanks to the presence of the shunt capacitors, the effective capacitance of the line is enhanced, and the phase velocity of the structure can be made significantly smaller than the one of the unloaded line. The target is to achieve the layout of the slow-wave structure able to provide the required slow-wave ratio, characteristic (Bloch) impedance and electrical length (i.e., the usual specifications in the design of slow-wave transmission lines). To this end, a two-step synthesis method, based on the aggressive space mapping (ASM) algorithm, is proposed for the first time. Through the first ASM algorithm, the circuit schematic providing the target specifications is determined. Then, the second ASM optimizer is used to generate the layout of the structure. To illustrate the potential of the proposed synthesis method, three application examples are successfully reported. The two-step ASM algorithm is able to provide the layout of the considered structures from the required specifications, without the need of an external aid in the process.