Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Room Temperature Ethanol Microsensors Based on Silanized Tungsten Oxide Nanowires

  • Vallejos, Stella
  • Fohlerová, Zdenka
  • Tomić, Milena
  • Gràcia Tortadès, Isabel
  • Figueras Costa, Eduard
  • Cané Ballart, Carles
Gas microsensors based on tungsten oxide (WO3-x) nanowires (NWs) silanized with APTES (3-aminopropyltriethoxysilane) are developed in this work. These surface modified microsensors are highly sensitive to ethanol at room temperature (RT) via photoactivation and show enhanced selectivity towards other volatile organic compounds (VOCs) including acetone and toluene., This work has been supported by the Czech Science Foundation (GAČR) via Grant no. 17-16531S. The support of the Spanish Ministry of Economy and Competitiveness via the Ramón y Cajal programme and projects TEC2015-74329-JIN-(AEI/FEDER, EU) and TEC2016-79898-C6-1-R (AEI/FEDER, EU) are also acknowledged, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Cerium oxide-tungsten oxide core-shell nanowire-based microsensors sensitive to acetone

  • Tomić, Milena
  • Šetka, Milena
  • Chmela, Ondřej
  • Gràcia Tortadès, Isabel
  • Figueras Costa, Eduard
  • Cané Ballart, Carles
  • Vallejos, Stella
Gas sensitive cerium oxide-tungsten oxide core-shell nanowires are synthesized and integrated directly into micromachined platforms via aerosol assisted chemical vapor deposition. Tests to various volatile organic compounds (acetone, ethanol, and toluene) involved in early disease diagnosis demonstrate enhanced sensitivity to acetone for the core-shell structures in contrast to the non-modified materials (i.e., only tungsten oxide or cerium oxide). This is attributed to the high density of oxygen vacancy defects at the shell, as well as the formation of heterojunctions at the core-shell interface, which provide the modified nanowires with ‘extra’ chemical and electronic sensitization as compared to the non-modified materials., This work has been supported by the Czech Science Foundation (GAČR) via Grant no. 17-16531S, and the Spanish Ministry of Science and Innovation via the Ramón y Cajal Programme and Grants TEC2015-74329-JIN-(AEI/FEDER,EU) and TEC2016-79898-C6-(AEI/FEDER,EU). This research has used the Spanish ICTS Network MICRONANOFABS (partially funded by MINECO). CEITEC Nano Research Infrastructure (IDLM2015041, MEYS CR, 2016–2019) is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

ZIF Nanocrystal-Based Surface Acoustic Wave (SAW) Electronic Nose to Detect Diabetes in Human Breath

  • Bahos, Fabio Andrés
  • Sainz-Vidal, Arianee
  • Sánchez-Pérez, Celia
  • Saniger, José
  • Gràcia Tortadès, Isabel
  • Saniger-Alba, María M.
  • Matatagui, Daniel
In the present work, a novel, portable and innovative eNose composed of a surface acoustic wave (SAW) sensor array based on zeolitic imidazolate frameworks, ZIF-8 and ZIF-67 nanocrystals (pure and combined with gold nanoparticles), as sensitive layers has been tested as a non-invasive system to detect different disease markers, such as acetone, ethanol and ammonia, related to the diagnosis and control of diabetes mellitus through exhaled breath. The sensors have been prepared by spin coating, achieving continuous sensitive layers at the surface of the SAW device. Low concentrations (5 ppm, 10 ppm and 25 ppm) of the marker analytes were measured, obtaining high sensitivities, good reproducibility, short time response and fast signal recovery., This work has been supported by Universidad Nacional Autónoma de México via Grants DGAPA-UNAM-PAPIIT TA100118 and DGAPA-UNAM-PAPIIT IT100518, the Fundación General CSIC via Programa ComFuturo, and the Spanish Ministry of Science and Innovation via Grant TEC2016-79898-C6-(AEI/FEDER,EU). This research has used the Spanish ICTS Network MICRONANOFABS (partially funded by MINECO), We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Portable low-cost electronic nose based on surface acoustic wave sensors for the detection of BTX vapors in air

  • Matatagui, Daniel
  • Bahos, Fabio Andrés
  • Gràcia Tortadès, Isabel
  • Horrillo, Carmen
A portable electronic nose based on surface acoustic wave (SAW) sensors is proposed in this work to detect toxic chemicals, which have a great potential to threaten the surrounding natural environment or adversely affect the health of people. We want to emphasize that ferrite nanoparticles, decorated (Au, Pt, Pd) and undecorated, have been used as sensitive coatings for the first time in these types of sensors. Furthermore, the proposed electronic nose incorporates signal conditioning and acquisition and transmission modules. The electronic nose was tested to low concentrations of benzene, toluene, and xylene, exhibiting excellent performance in terms of sensitivity, selectivity, and response time, indicating its potential as a monitoring system that can contribute to the detection of toxic compounds., This work was supported by the Fundación General CSIC via Programa ComFuturo and the Spanish Ministry of Science, Innovation and Universities under the projects RTI2018-095856-B-C22 (AEI/FEDER) and TEC2016-79898-C6 (AEI/FEDER)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Love Wave Sensors with Silver Modified Polypyrrole Nanoparticles for VOCs Monitoring

  • Šetka, Milena
  • Bahos, Fabio Andrés
  • Matatagui, Daniel
  • Gràcia Tortadès, Isabel
  • Figueras Costa, Eduard
  • Drbohlavová, Jana
  • Vallejos, Stella
© 2020 by the authors., Love wave sensors with silver-modified polypyrrole nanoparticles are developed in this work. These systems prove functional at room temperature with enhanced response, sensitivity and response time, as compared to other state-of-the-art surface acoustic wave (SAW) sensors, towards volatile organic compounds (VOCs). Results demonstrate the monitoring of hundreds of ppb of compounds such as acetone, ethanol and toluene with low estimated limits of detection (~3 ppb for acetone). These results are attributed to the use of silver-modified polypyrrole as a second guiding/sensitive layer in the Love wave sensor structure, which provides further chemically active sites for the gas-solid interactions. The sensing of low VOCs concentrations by micro sensing elements as those presented here could be beneficial in future systems for air quality control, food quality control or disease diagnosis via exhaled breath as the limits of detection obtained are within those required in these applications., This research was funded by the Czech Science Foundation (GACR) via Grant No. 20-20123S, ˇ the Spanish Ministry of Economy and Competitiveness via projects TEC2015-74329-JIN-(AEI/FEDER, EU), and TEC2016-79898-C6-1-R (AEI/FEDER, EU) and by Universidad Nacional Autónoma de México via Grant DGAPA-UNAM-PAPIIT TA100118. The support of the “Ramón y Cajal” programme is also acknowledged. This research has made use of the infrastructures the Spanish ICTS Network MICRONANOFABS, partially supported by MINECO, and Czech CEITEC Nano Research Infrastructure, supported by MEYS (2016-2019)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of Mg Doping Levels on the Sensing Properties of SnO2 Films

  • Bendahmane, Bouteina
  • Tomić, Milena
  • Touidjen, Nour El Houda
  • Gràcia Tortadès, Isabel
  • Vallejos, Stella
  • Mansour, Farida
© 2020 by the authors., This work presents the effect of magnesium (Mg) doping on the sensing properties of tin dioxide (SnO2) thin films. Mg-doped SnO2 films were prepared via a spray pyrolysis method using three doping concentrations (0.8 at.%, 1.2 at.%, and 1.6 at.%) and the sensing responses were obtained at a comparatively low operating temperature (160 °C) compared to other gas sensitive materials in the literature. The morphological, structural and chemical composition analysis of the doped films show local lattice disorders and a proportional decrease in the average crystallite size as the Mg-doping level increases. These results also indicate an excess of Mg (in the samples prepared with 1.6 at.% of magnesium) which causes the formation of a secondary magnesium oxide phase. The films are tested towards three volatile organic compounds (VOCs), including ethanol, acetone, and toluene. The gas sensing tests show an enhancement of the sensing properties to these vapors as the Mg-doping level rises. This improvement is particularly observed for ethanol and, thus, the gas sensing analysis is focused on this analyte. Results to 80 ppm of ethanol, for instance, show that the response of the 1.6 at.% Mg-doped SnO2 film is four times higher and 90 s faster than that of the 0.8 at.% Mg-doped SnO2 film. This enhancement is attributed to the Mg-incorporation into the SnO2 cell and to the formation of MgO within the film. These two factors maximize the electrical resistance change in the gas adsorption stage, and thus, raise ethanol sensitivity., This work was supported by the Spanish Ministry of Economy and Competitiveness via project TEC2016-79898-C6-1-R (AEI/FEDER, EU) and the ‘Ramón y Cajal’ Programme. Part of this research used the Czech CEITEC Nano Research Infrastructure, supported by MEYS (2016–2019)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Gas sensitive ZnO structures with reduced humidity-interference

  • Vallejos, Stella
  • Gràcia Tortadès, Isabel
  • Pizúrová, Naděžda
  • Figueras, Eduard
  • Čechal, Jan
  • Hubálek, J.
  • Cané, Carles
Gas microsensors based on zinc oxide structures with rod- and needle-like morphology, both integrated via a non-catalyzed vapor-solid mechanism enabled using aerosol-assisted chemical vapor deposition, are developed. Analyses of the films via SEM, TEM, XPS, and water contact angle indicate a higher concentration of oxygen vacancies, higher aspect ratio and higher roughness factor for the needles than for the rods. Gas sensing tests towards hydrogen and carbon monoxide demonstrate reduced humidity-interference, and higher responses to the analytes for the needle-based systems compared to the rods. These results are attributed to the morphology of the sensitive materials, which not only affects the surface-area-to-volume-ratio of the films but also their surface chemistry. These findings indicate that a thorough optimization of morphology, structure and surface properties of gas sensitive metal oxides could allow for more reliable sensor operation in humid conditions., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Highly hydrogen sensitive micromachined sensors based on aerosol-assisted chemical vapor deposited ZnO rods

  • Vallejos, Stella
  • Gràcia Tortadès, Isabel
  • Lednický, Tomáš
  • Vojkuvka, Lukáš
  • Figueras, Eduard
  • Hubálek, J.
  • Cané, Carles
Chemoresistive gas microsensors with highly hydrogen sensitive zinc oxide rods dominated by exposed {100} surfaces are fabricated. The hexagonal rod structures are integrated into micromachined transducing platforms without the need for substrate pre-treatment, via a vapor-solid mechanism enabled using an aerosol-assisted chemical vapor deposition method. The microsensors demonstrate an enhanced functionality towards hydrogen, with greater sensor responses (between 200% and 1800%) compared to other gases including ethanol, carbon monoxide, acetone, and toluene, and with low interferences among these reductive gases. The improved functionality of these systems towards hydrogen is attributed to the formation of an accumulation layer at the zinc oxide rods after hydrogen exposure, which includes a mechanism not only dominated by the oxygen vacancies, but also by the formation of intermediate energy levels for the transfer of charge from hydrogen to the zinc oxide conduction band., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Highly sensitive SnO<inf>2</inf> nanowire network gas sensors

  • Domènech-Gil, Guillem
  • Samà, Jordi
  • Fàbrega, Cristian
  • Gràcia Tortadès, Isabel
  • Cané, Carles
  • Barth, Sven
  • Romano-Rodríguez, Albert
In this work we present a methodology for the localized growth of nanowires on prespecified areas of microhotplates that allows to independently adjust the device's resistance and its response to the gas. This is achieved through the fabrication stripes containing the nanowires, with or without the presence of a gap in the stripe, giving rise that the nanowires bridge the current. The methodology is demonstrated growing SnO2 nanowire-based chemoresistors and the fabricated sensors have been characterized against CO and NO2. The results show the capability of tailoring nanowire stripe sizes from 1 to 100 µm, including empty areas of the same sizes along the sensing material, and a response increase by a factor of up to 500. We attribute the response enhancement to the absence of nucleation seeds in the gap area, where only arching nanowires can allow the current to flow between electrodes. In this way, the current flow along the bridge of nanowires is restricted principally to the surface conduction, which is controlled by the interaction of the nanowires with gases., This work has been partially supported by the Spanish Ministerio de Economía y Competitividad , through project TEC2016-79898-C6 (AEI/FEDER, EU) and Ministerio de Economía e Innovación , through project PID2019-107697RB-C41/AEI/10.13039/501100011033, and by the European Cooperation in Science and Technology , through Action TD1105 EuNetAir. S. B. acknowledges funding by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) in the Heisenberg Programme (BA 6595/1-1; grant no: 413940754 )., Peer reviewed