Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 13
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

NH3 oxidation and NO reduction by NH3 in N2/Ar and CO2 atmospheres

  • Alzueta, María U.
  • Mercader, Víctor D.
  • Giménez-López, Jorge
  • Bilbao, Rafael
Impact of using CO2 or N2/Ar as bath gas, representative respectively of oxy-fuel or air combustion scenarios, has been evaluated on the oxidation of ammonia under a variety of operating conditions in a combined experimental and simulation study. Variables of relevance as temperature and oxygen stoichiometry have been considered at atmospheric pressure and under carefully controlled experimental conditions. Additionally, the impact of the presence of NO, which can be formed from ammonia oxidation, has also been evaluated. The experimental results obtained have been simulated with significant success with a detailed literature kinetic mechanism, which has been further used to interpret the main experimental observations. The results obtained are of interest in the power and energy industry, and can be used for guiding the co-firing of NH3 and carbon containing fuels.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Flow Reactor Oxidation of Ammonia–Hydrogen Fuel Mixtures

  • Alzueta, Maria U.
  • Mercader, Victor
  • Cuoci, Alberto
  • Gersen, Sander
  • Hashemi, Hamid
  • Glarborg, Peter
Hydrogen-assisted oxidation of ammonia under flow reactor conditions was investigated through experiments and chemical kinetic modeling. Novel experiments, conducted in a tubular laminar flow reactor as a function of the NH3/H-2 ratio, stoichiometry, and temperature (725-1475 K), were analyzed along with literature results from tubular and jet-stirred flow reactors. Ignition and oxidation of NH3 is strongly promoted by the presence of H-2 under all conditions investigated. In general, the behavior is captured well by the kinetic model. With an increasing fraction of H-2 in the fuel mixture, the generation of chain carriers gradually shifts from being controlled by the amine reaction subset to being dominated by the oxidation chemistry of H-2, which is known more accurately. However, under reducing conditions, the H-2 consumption rate is strongly underpredicted. This shortcoming suggests that the thermochemistry of amine radicals and/or the formation of higher amines need further assessment. The present analysis shows that for lean oxidation of NH3/H-2 mixtures in tubular flow reactors, data obtained at higher temperatures, particularly for NO formation, may be strongly affected by the reaction during preheating or by mixing (dependent on reactor design) in the inlet section prior to the isothermal zone. Modeling predictions for the high pressure, medium-temperature ignition conditions in a large diesel engine indicate that NH3/H-2 fuel mixtures may still require a cofuel to secure stable ignition.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Conversion of NH3/CO/NO/CO2 mixtures

  • Alzueta, María U.
  • Salas, Iris
The present work addresses the impact of the presence of both CO and NO during the conversion of NH3 using CO2 or N2/Ar as bath gas, which would correspond to oxy-fuel or conventional air fuel combustion processes respectively. The variation of temperature and oxygen excess ratio is studied in a flow reactor setup at atmospheric pressure. Experimental results have been simulated with a literature detailed kinetic mechanism and the main observations have been discussed. The main results indicate that the effect of the presence of CO is less important than in other reactive systems. Conversion of NH3 is almost insensitive to the presence of CO, and the temperature regime for NH3 conversion is only significantly affected under fuel-lean conditions. The present results extend the experimental database on ammonia conversion, for different mixtures and conditions, and contribute to evaluate the possibilities of improving the ignition of this compound.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Oxidation of methylamine (CH3NH2)/CH4/NO mixtures in an atmospheric-pressure flow reactor

  • Alzueta, María U.
  • Pérez, Teresa
  • Marrodán, Lorena
The oxidation of methylamine (CH3NH2) and methane mixtures has been studied by experiments in a flow reactor at atmospheric pressure and temperatures of 350–1450 K. In addition to temperature, stoichiometry (ranging from fuel-rich to fuel-lean conditions) and the presence of NO have been evaluated. Several diagnostic techniques have been used to experimentally quantify many different species: gas chromatography, Fourier Transform Infra-red spectroscopy (FTIR) and an infra-red NO analyzer. Results show a negligible influence of stoichiometry both on the conversion of MEA and CH4 in the absence of NO, while the presence of NO acts to inhibit the conversion of CH4 with no appreciable influence on MEA conversion. This indicates the complex interaction occurring in the MEA/CH4/NO mixtures, for which the mechanism is not able to properly predict the conversion of CH4 in the presence of NO, while the rest of compounds are well reproduced both in the absence and presence of NO. This fact, together with the probable formation of species containing C and N, due to the presence of additional unidentified species and the deep analysis of the mass balances carried out, supports the idea of the formation of C-N species, not clearly identified so far. The literature mechanism used in simulations has provided good results in reproducing most of the species and conditions considered. The largest discrepancy has been observed for CH4 conversion in the presence of NO, supporting the existence of missing interactions in the mechanism.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Combustion of NH3/DME and NH3/DME/NO mixtures

  • Ruiz-Gutiérrez, A.
  • Rebollo, P.
  • Alzueta, M.U.
The objective of this work is to study the oxidation of ammonia and dimethyl ether mixtures (NH3/DME) both in the absence and the presence of monoxide of nitrogen (NO). For this purpose, laboratory experiments have been conducted in a quartz flow reactor setup in the 875–1425 K temperature range at atmospheric pressure, modifying the oxygen excess ratio (λ), and the NH3/DME mixture ratio with and without NO. The experimental results have been simulated with a literature-based kinetic mechanism. The results show that the presence of DME and an oxygen excess ratio affect the conversion of NH3, shifting its oxidation to lower temperatures, which decrease as the DME concentration in the mixture and λ increase. Interactions between ammonia and DME seem to be important under the studied conditions, presumably involving the formation and thermal decomposition of methyl nitrite (CH3ONO). These interactions affect the oxidation of ammonia at low temperatures, consume and produce NO, which would determine the final NO emission. When there is NO in the NH3/DME mixtures, NO is reduced up to 60 %, also favouring the oxidation of ammonia, but with an almost imperceptible effect of NO in the case of DME. The addition of different concentrations of DME also affects the oxidation behaviour of ammonia in NH3/DME/NO mixtures. In general, the conversion of both NH3 and DME is highly determined by the concentration of OH radicals, although thermal decomposition is also relevant for DME.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Polycyclic aromatic hydrocarbons formed during the pyrolysis of dimethoxymethane (DMM). Comparison with other oxygenated additives

  • Viteri, Fausto
  • Alexandrino, Katiuska
  • Millera, Ángela
  • Bilbao, Rafael
  • Alzueta, María U.
The influence of the temperature (1075 – 1475 K) and inlet concentration of fuel (33,333 and 50,000 ppmv) on the formation of the 16 EPA-priority Polycyclic Aromatic Hydrocarbons (PAH) from the pyrolysis of dimethoxymethane (DMM) was analyzed. PAH were detected in different phases (gas phase, adsorbed on soot, and stuck on the reactor walls) and quantified by gas chromatography-mass spectrometry (GC–MS). Additionally, the toxicity of the PAH samples, expressed as B[a]P-eq, was analyzed in all experiments. A comparison with the results obtained from the pyrolysis of other oxygenated compounds was also performed and similar behaviors were observed. The main results showed that, at low temperatures, the highest concentrations of PAH were found in the gas phase, while at high temperatures were found on soot. For both inlet concentrations of DMM, the light PAH, such as naphthalene and acenaphthylene, were found in major concentrations, in all phases and temperatures. The heavy PAH, such as fluoranthene and pyrene, increased its concentration on soot at highest temperatures. The highest formation of soot was obtained at 1475 K and follows the trend: 2,5DMF < tert-butanol < 2MF < 2butanol < iso-butanol < 1-butanol < ethanol < DMC < DMM. The highest formation of PAH was at 1275 K with the tendency: tert-butanol < 2-butanol < 1-butanol < 2,5DMF < 2MF < iso-butanol < ethanol < DMC < DMM. The highest B[a]P-eq value was found in the pyrolysis of 2,5DMF, and the lowest in the pyrolysis of DMM.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

High-pressure conversion of ammonia additivated with dimethyl ether in a flow reactor

  • García-Ruiz, Pedro
  • Ferrando, Pablo
  • Abián, María
  • Alzueta, María U.
The oxidation of ammonia (NH3) mixed with dimethyl ether (DME) was investigated from experimental and modeling points of view using a quartz flow reactor with argon as bath gas from 350 K to 1225 K, for two different DME/NH3 ratios (0.05 and 0.3), three oxygen excess ratios (λ = 0.7, 1 and 3) and various pressures (1, 10, 20 and 40 bar). The effect of pressure, oxygen stoichiometry, temperature, and DME/NH3 ratio has been analyzed on DME, NH3, NO, NO2, N2O, N2, O2, H2, HCN, CH4, CO, and CO2 concentrations. The present study indicates that oxygen availability, DME/NH3 ratio, and pressure are important variables that shift NH3 and DME conversion to lower temperatures as their values increase. Under certain conditions, the pressure effect can avoid NO and HCN production, which would represent a benefit for pressure applications. The main products of ammonia/dimethyl ether oxidation are N2, N2O, CO, and CO2, and under certain conditions, NO, H2, CH4, and HCN are also produced. NO2 is always detected below 5 ppm for all the conditions considered. The N2O formation is favored by increasing the O2 stoichiometry, pressure, and/or DME/NH3 ratio. The experimental results are interpreted and discussed in terms of an updated detailed chemical kinetic mechanism, which captures, with a general good agreement, the main trends of NH3 and DME conversion under the considered conditions. Despite this, some calculated species present discrepancies with the experimental results. The main challenge is the consideration of the C-N interactions that can be present in the combustion of DME/NH3 mixtures.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Use of methanol as a promoter for ammonia combustion

  • Ruiz-Gutiérrez, A.
  • Diego, I. de
  • Alzueta, M.U.
This work aims to study the oxidation of ammonia and methanol mixtures (NH3/CH3OH). For this purpose, laboratory experiments were conducted using a quartz flow reactor at atmospheric pressure, in a temperature range of 875–1425 K. The oxygen excess ratio (λ) and the NH3/CH3OH ratio were modified during the experiments. The experimental results have been simulated with a literature-based kinetic mechanism. The results show that the presence of CH3OH and the oxygen excess ratio affect the conversion of NH3, shifting its oxidation to lower temperatures as these variables increase. The oxidation of both fuels was slightly boosted with increasing CH3OH concentration. The λ study showed that the fuel-lean conditions accelerate NH3 oxidation at lower temperatures whereas do not have the same effect on CH3OH oxidation. The H radical concentration significantly influences fuel consumption, especially in reactions involving CH3OH and NH2, and it is also key for inhibition processes. CH3OH was found to initiate NH3 reactions, with strong competition for OH radicals between the two fuels. Nevertheless, methanol helps reduce ammonia's oxidation temperature. CH2OH was identified as the predominant species following H-abstraction from CH3OH. In the NH3/CH3OH ratio studies, increasing methanol concentration lowered the oxidation temperature of both fuels, with a temperature difference of up to 150 K observed for NH3/CH3OH ratios from 0.6 to 10. Increasing methanol concentration for a given NH3 value also shifted the prominence of secondary reaction pathways, further influencing the overall oxidation process.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

High-Pressure Oxidation of Ammonia Mixed with Dimethoxymethane

  • Alexandrino, Katiuska
  • Andrés, Álvaro
  • Callejas, Alicia
  • Alzueta, María U.
The oxidation of ammonia-dimethoxymethane (NH3-DMM) mixtures at high pressure was analyzed from both experimental and kinetic modeling points of view. Experiments were performed using a laboratory tubular flow reactor installation and were conducted at 10, 20, and 40 bar under fuel-rich (λ = 0.7), stoichiometric (λ = 1), and fuel-lean (λ = 3) conditions and temperatures ranging from 650 to 1250 K. The inlet DMM concentration was varied (100 and 200 ppm), keeping the concentration of ammonia constant at 1000 ppm. The data were interpreted in terms of a detailed chemical kinetic model. Despite some discrepancy between the model predictions and measurements, the model accurately followed the experimental trends, highlighting its ability to describe the oxidation of the NH3-DMM mixture. The experimental and predicted results suggested that the conversion of both ammonia and DMM was favored by increased pressure and higher inlet concentrations of O2 and DMM. Under the conditions of the present work, the dominant path for ammonia and DMM conversion leads to N2/N2O and CO/CO2 in any case. Concentrations of NO and NO2 were below the detection limit in all the experimental conditions studied, which imply a benefit in the reduction of NOx emissions during the combustion of pure ammonia. DMM enhanced the ammonia reactivity, although its presence leads to the formation of CO2 not only by the common CO + OH reaction but also through the interaction of N2O with CO.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Flow Reactor Study of NH3/DEE Oxidation Chemistry

  • Ruiz-Gutiérrez, A.
  • Bello-Gallego, A.
  • Alzueta, M. U.
The pursuit of environmentally sustainable alternatives to conventional fuels is essential today. Ammonia emerges as a promising candidate, though its inherent disadvantages must be addressed. Co-firing ammonia with fuels exhibiting superior thermochemical properties is one of the most widely accepted solutions. The present study investigates the oxidation of ammonia and diethyl ether mixtures (NH3/DEE). To this end, a quartz flow reactor was employed at atmospheric pressure, within a temperature range of 875–1425 K. The oxygen excess ratio (λ) and the NH3/DEE mixture ratio were systematically varied during the experiments. The results show an increase in the reactivity of ammonia when mixed with DEE. During pyrolysis, DEE is inhibited by competition for H radicals, which are essential for initial conversion steps. DEE undergoes thermal decomposition without a significant radical pool, while NH3 reactivity remains low. With the increase of the oxygen excess ratio, fuel oxidation occurs at lower temperatures. Hydroxyl (OH) and atomic oxygen (O) radicals are crucial in NH3 oxidation, while the presence of DEE derivatives further promote this oxidation, although both fuels exhibit competitive behavior regarding radical consumption. Variations in λ do not cause a significant effect in the oxidation temperature of DEE, with OH radicals playing a central role in the minor differences observed. Hydrogen abstraction via interaction with H radicals is the most important consumption reaction of DEE, mainly occurring at the secondary carbon position. Conversely, the production and interaction of derivatives at other positions contribute to the most inhibitory reactions in DEE oxidation. The NH3/DEE ratio has a significant impact on ammonia oxidation, particularly under high DEE dilution conditions (NH3/DEE = 10). OH and H radicals drive oxidation, while an increased DEE concentration leads to CH3 radical formation, enhancing fuel consumption. A literature-based kinetic mechanism, modified in the present work, was employed to represent and interpret the current results accurately.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Pyrolysis of ethylene – ammonia mixture: Formation of soot, gases and PAH

  • Viteri, Fausto
  • Soler, María
  • Starace, Paola
  • Abián, María
  • Alzueta, María U.
The effect of inlet concentration of NH3 (0, 30000, 60000, and 100000 ppm) and temperature (1275, 1375, and 1475 K) on the formation of soot, gases and polycyclic aromatic hydrocarbons (PAH) from the pyrolysis of C2H4/NH3 mixtures with constant concentration of C2H4 (30000 ppm) was analyzed. Light gases were quantified through gas chromatography, while soot was collected in a fiber filter, at the reactor outlet, and the particle diameter was analyzed. The PAH were analyzed through gas chromatograph coupled to mass spectrometer by considering the 16 PAH reported by Environmental Protection Agency (EPA) as priority pollutants. The main results show that the higher the presence of NH3 in the NH3/C2H4 mixture, the lower the soot formation. This decrease of soot is accompanied by an increase of HCN and a decrease in C2H2, indicating that the carbon has been removed from the typical soot reaction pathways. In all conditions tested, PAH formed follow the typical trend observed in earlier works with respect to temperature, i.e. as the temperature increases, the formation of PAH decreases. At 1275 K, the presence of high NH₃ levels increases PAH concentrations, likely due to suppression of soot formation routes, which prevents PAH consumption and allows aromatic intermediates to accumulate rather than proceed to particle growth. The increase in NH3 concentrations at the inlet reduces the toxicity expressed as benzo[a]pyrene equivalent concentration (B[a]P-eq), under all conditions studied. Analysis of the particle distribution diameter reveals that the NH3 presence reduces diameter variations and predominantly results in smaller soot particles.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Oxidation of diethyl ether/ammonia mixtures in a flow reactor at different pressures

  • García-Ruiz, P.
  • García, M.
  • Abián, M.
  • Alzueta, M.U.
Ammonia (NH3) in their mixtures with diethyl ether (DEE) represents a strategy to reduce CO2 emissions and overcome the limitations of NH3 combustion, even for a small addition of DEE (5 %). DEE is considered a potential substitute for fossil fuels when obtained from bioethanol. The present work performs an experimental and kinetic analysis of DEE/NH3 oxidation and the formation of combustion products at different pressures (1–40 bar), in the 290 K–1180 K temperature range using a quartz tubular flow reactor by analyzing the effects of the main variables (pressure, temperature, oxygen excess ratio, and DEE/NH3 ratio) using argon as a bath gas. The results indicate that either increasing pressure, DEE/NH3 ratio, or oxygen availability results in a shift of NH3 and DEE conversion to lower temperatures. DEE and NH3 show a negative temperature coefficient (NTC) phenomenon at low temperatures, influenced by pressure, oxygen excess, and the DEE/NH3 ratio. The pressure effect is particularly significant in the low pressures studied. The main nitrogen products are N2 and N2O. HCN is only produced under atmospheric pressure, while NO2 and NO concentrations are below the detection limit under all considered conditions. N2O formation is favored by increasing stoichiometry, pressure, and DEE/NH3 ratio. Apart from CO and CO2, CH4, CH3OH, C2H4, and CH3CHO have been found as produced carbon pecies. The experimental results are interpreted in terms of a chemical kinetic mechanism for DEE/NH3 mixtures, which can describe the main trend of NH3 and DEE conversion under the studied conditions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publicación Artículo científico (JournalArticle)

Flow reactor study of NH3/DMM oxidation

  • Ruiz-Gutiérrez, Adrián
  • Mazano-Peña, Daniel
  • Alzueta, María U.
This study presents a comprehensive investigation of the conversion of ammonia (NH3) and dimethoxymethane (DMM) mixtures in a quartz flow reactor. Experiments were carried out at atmospheric pressure and across a wide range of conditions to elucidate species profiles, many of which have not been extensively characterised previously. The operational parameters included temperatures between 875 and 1425 K, NH3/DMM ratios from 0.48 to 10.86, and oxygen excess ratios (λ) from 0 to 3.12. Quantification of numerous compounds was achieved using a micro gas chromatograph (GC) in combination with a continuous gas analyser. Simulations with an updated detailed chemical kinetic mechanism were carried out in order to elucidate the conversion pathways of the mixture constituents. Calculations were in good consistency with the experimentally observed ones for the key species. NH3 conversion was highly sensitive to variations in O2, whereas DMM exhibited only minor changes in its reaction temperature (approximately 50 K). The principal consumption pathway of DMM involves hydrogen abstraction from the central carbon by CH3 radicals. This facilitates the access of ammonia to a greater number of radicals, as competition for OH or O radicals is less pronounced. NO formation was influenced by the presence of DMM, increasing with both the oxygen excess ratio (λ) and the proportion of DMM in the mixture. It was further concluded that DMM exerts a significant influence on NH3 behaviour when the NH3/DMM ratio is ≤ 1, an effect that decreases at higher initial O2 concentrations (λ > 1). Overall, this work provides new insights into the conversion behaviour of NH3/DMM mixtures under the investigated conditions and provides essential reference data for further development of detailed kinetic models.