Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Highly selective CO formation via CO2 hydrogenation over novel ceria-based high-entropy oxides (HEOs)

  • Cortazar, Maria
  • Lafuente, Marta
  • Navarro-Puyuelo, Andrea
  • Garcia, Xènia
  • Llorca, Jordi
  • Reyero, Inés
  • Bimbela, F.
  • Gandía, Luis M.
In the present study, new ceria-based high-entropy oxides (HEOs) were investigated as CO2 hydrogenation catalysts. The nominal composition was (Ce0.5Ni0.1Co0.1Cu0.1Zn0.1Mg0.1)Ox and the synthesis was accomplished through the citrate complexing sol–gel method. Characterization techniques utilized including ICP-AES, in situ XRD and in situ XPS, SEM-EDS, HR-TEM and HAADF-STEM, Raman spectroscopy, H2-TPR, CO2-TPD and N2 physical adsorption. The physicochemical characterization and the catalytic results revealed that the conditions of the thermal treatments at which the oxides were subjected critically determined the catalytic performance, especially the CO2 hydrogenation products selectivities. Calcination in air and/or reduction in hydrogen conducted at temperatures below 500 °C led to active but poorly selective catalysts that produced both methane and CO with significant yields. This was mainly attributed to the presence of metallic Cu, Ni and Co on the catalysts that appeared to be supported on ceria doped with the rest of the formulation elements. In contrast, thermal treatments at 750 °C favored the formation of a rocksalt entropy-stabilized (NiCoCuZnMg)Ox HEO supported on ceria that has stood out for showing an excellent selectivity towards the reverse water–gas shift (RWGS) reaction. This catalyst led to CO selectivities of almost 100 % over a very wide range of reaction temperatures (300–700 °C). Long-term stability tests (100 h) showed only a slight decrease in CO2 conversion, while CO selectivity remained stable at nearly 100 % at 400 °C. XRD characterization of the used catalysts evidenced that, whereas the basic catalyst structure remained, some metallic copper exsolved during reduction and reaction period. These results are relevant and very promising, opening a door to the development of new catalysts for the valorization of CO2 through the RWGS reaction, thus expanding the low-temperature limit at which this process can be carried out selectively., Authors wish to thank the Spanish Agencia Estatal de Investigación (AEI) and Ministerio de Ciencia e Innovación (MCIN), the European Regional Development Fund (ERDF/FEDER), the European Union’s NextGenerationEU funds for their financial support. In particular, this work was partially funded by the following research projects: TED2021-130846B-I00 (MULTIeFUEL project), PID2021-127265OB-C21 (SOLFUEL project), PLEC2022-009221 (Panel-to-Fuel project), PID2021-124572OB-C31, and CEX2023-001300-M. M. Cortazar and M. Lafuente also thank Ministerio de Universidades (Spain) and NextGenerationEU funds for their ¨Margarita Salas¨ postdoctoral grants. JL is a Serra Húnter Fellow and is grateful to ICREA Academia program., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001300-M)., Open access funding provided by Universidad Pública de Navarra., Peer reviewed
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Remarkable performance of supported Rh catalysts in the dry and combined reforming of biogas at high space velocities

  • Navarro Puyuelo, Andrea
  • Atienza Martínez, María
  • Reyero Zaragoza, Inés
  • Bimbela Serrano, Fernando
  • Gandía Pascual, Luis
Dry and combined (with O2) reforming of synthetic biogas were studied at 700 °C using 0.5 % Rh catalysts prepared by impregnation on different supports: γ-Al2O3, SiO2, TiO2, ZrO2 and CeO2. Gas hourly space velocity (GHSV) was varied between 150 and 700 N L CH4/(gcat·h), and two O2/CH4 molar ratios of 0 and 0.12 were studied. Rh/Al2O3 catalysts (prepared using two different commercial supports here denoted as Sph and AA) presented the highest biogas conversion and syngas yields under both dry and combined reforming conditions. Catalytic activities were as follows: Rh/AA ≈ Rh/Sph > Rh/SiO2 > Rh/ZrO2 ≈ Rh/CeO2 > Rh/TiO2. The effect of catalysts’ calcination pre-treatment at relatively low (200 °C) and high temperatures (750 °C) was also studied. Calcination at high temperatures had a detrimental effect on both dry and combined reforming activities. However, a positive effect on the reforming activities and syngas yields was observed when the catalysts were calcined at 200 °C, especially under biogas combined reforming conditions: higher CH4 conversions and syngas yields could be achieved, as well as increasing CO2 conversions, though at the expense of lower H2/CO molar ratios., The financial support of the Spanish Agencia Estatal de Investigación (AEI) and Ministerio de Ciencia e Innovación (MCIN), the European Regional Development Fund (ERDF/FEDER), the European Union´s NextGenerationEU funds. In particular, this work was partially funded by the following research projects: TED2021-130846B-I00 (MULTIeFUEL project), PID2021-127265OB-C21 (SOLFUEL project) and PLEC2022-009221 (Panel-to-Fuel project). Open access funding provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Renewable platform chemicals from biomass: pathways, technologies and challenges

  • Moreira, Rui
  • Atienza Martínez, María
  • Gil-Lalaguna, Noemí
  • Bimbela Serrano, Fernando
  • Cornejo Ibergallartu, Alfonso
  • Serra, Arménio
  • Coelho, Jorge
  • Gandía Pascual, Luis
  • Arauzo, Jesús María
  • Sánchez, José Luis
The production of renewable chemicals and plastics has been extensively investigated in recent decades, with the purpose of reducing the global dependence on fossil resources. In this review, the main routes to produce chemicals from biomass are reviewed and a critical discussion on the prospects and techno-economic viability of these technologies is presented. As these topics are often considered as independent from each other, the aim of this work is to provide an unified and interdisciplinary perspective of main possible production routes and their development status for experts and non-experts. The main processes of biomass concentration were reviewed and two main approaches for obtaining renewable chemicals were considered: (i) the production of compounds chemically identical to petroleum derivatives, and (ii) the production of conventional and new oxygenated chemicals. The literature shows that there are sustainable technological alternatives to the substitution of many petroleum derived chemicals, but the complexity of the production processes should not be simplistically evaluated. Solutions and technologies must be carefully evaluated, both from the point of view of their technoeconomic viability and their sustainability., Rui Moreira would like to thank to the project agenda "From Fossil to Forest", funded by the PRR - Recovery and Resilience Program, of the Portuguese Republic, and by the Next Generation European funds (Call N.º 02/C05-i01/2022, Component 5 - Capitalization and Business Innovation-Mobilizing Agendas for Business Innovation). He also what to thank to CERES-Chemical Engineering and Renewable Resources for Sustainability Research Center, funded by Fundaçao para a Ciencia e a Tecnologia (FCT) and PRR (UID/00102/2025 and PRR UID/PRR/00102/2025, respectively). The UNIZAR team was funded by the Agencia Estatal de Investigación in Spain (Project PID2020-114936RB-I00) and Aragón Government (Research Group Ref. T22_23R) for providing frame support for this work. The UPNA team was fundend by the Spanish Agencia Estatal de Investigación (AEI) and Ministerio de Ciencia e Innovación (MCIN), the European Regional Development Fund (ERDF/FEDER), the European Union's NextGenerationEU funds for their financial support. In particular, this work was partially funded by the following research projects: TED2021-130846B-I00 (MULTIeFUEL project), PID2021-127265OB-C21 (SOLFUEL project), PLEC2022-009221 (Panel-to-Fuel project), PID2021-124572OB-C31.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Microkinetic modelling of CO2 and methane conversion into syngas on a low metal-loaded Rh/Al2O3 catalyst: effect of co-feeding reaction products

  • Navarro Puyuelo, Andrea
  • Reyero Zaragoza, Inés
  • Bimbela Serrano, Fernando
  • Kechagiopoulos, Panagiotis
  • Gandía Pascual, Luis
The effects of co-feeding the components of syngas (H2 or CO) in the CO2 and methane dry reforming were studied on a 0.5 wt.% Rh/Al2O3 catalyst by microkinetic modelling. Different inlet compositions, reaction temperatures (700–750 ◦C) and space velocities (530–2100 NL/(gcat⋅h)) were tested to develop a model consisting of 86 elementary reaction steps. The model described satisfactorily the trends found for CO2 and CH4 conversions, H2 and CO yields, and selectivities. Dehydrogenation of CH2* was identified as the rate determining step. The reaction pathway was not altered by H2 or CO co-feeding. Increasing the H2 concentration in the feed resulted in positive effects on the reactants conversions and syngas yield, due to augmented partial surface coverage by OH* and O* species, thus causing promoting effects on the reverse water–gas shift and methane steam reforming reactions. Conversely, CO co-feeding had negative effects on CO2 conversion, and H2 and CO yields, due to the high partial coverage of CO* and C*, which negatively affected the CO2 conversion and CH2* dehydrogenation step. This study provides new insights into the joint conversion of CO2 and CH4 into syngas on a low-loading Rh catalyst, showing the benefits of co-feeding hydrogen., The authors thank the Spanish Agencia Estatal de Investigación (AEI) and Ministerio de Ciencia e Innovación (MCIN), the European Regional Development Fund (ERDF/FEDER), and the European Union's NextGenerationEU funds for their financial support. In particular, this work was partially funded by the following research projects: TED2021-130846B-I00 (MULTIeFUEL project), PID2021-127265OB-C21 (SOLFUEL project) and PLEC2022-009221 (Panel-to-Fuel project). Dr. Andrea Navarro-Puyuelo thanks the AEI, the MCIN , and the EU's NextGenerationEU funds for funding her postdoctoral contract (PLEC2022-009221 project).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A prospective review on bioplastics and biopolymers

  • Moreira, Rui
  • Atienza Martínez, María
  • Gil-Lalaguna, Noemí
  • Serra, Arménio
  • Cornejo Ibergallartu, Alfonso
  • Bimbela Serrano, Fernando
  • Coelho, Jorge
  • Gandía Pascual, Luis
  • Arauzo, Jesús María
  • Sánchez, José Luis
The production of bioplastics has been extensively investigated in recent decades, with the purpose of reducing the global dependence on fossil resources. In this review, the main routes to produce bioplastics and a critical discussion of these technologies are presented. The synthesis routes to produce biodegradable and non-biodegradable bioplastics are discussed. Additionally, approaches to improve the environmental footprint of some conventional plastics that have no immediate solutions of substitution are also addressed. A comparison of the main properties of the bioplastics considered and a general perspective of the bioplastics market are also provided. Because these themes have often been reviewed separately, this article aims to provide a unified general perspective of bioplastics in the context of a biobased economy, as well as pointing out some of the hurdles in such way., The UC team and CERES - Chemical Engineering and Renewable Resources for Sustainability Research Center was funded by Fundação para a Ciência e a Tecnologia (FCT), through the base budgets (DOI: https://doi.org/10.54499/UIDB/00102/2020) and programm atic (DOI: https://doi.org/10.54499/UIDP/00102/2020). The UC team would like also to thank the COMPETE Programa Operacional Factores de Competitividade, FCT Fundação para a Ciência e Tecnologia, CEMMPRE (UID/EMS/00285/2020) and ARISE (LA/P/0112/2020). The UNIZAR team was funded by the Agencia Estatal de Investigación in Spain (Project PID2020-114936RB-I00) and Aragón Government (Research Group Ref. T22_23R) for providing frame support for this work. The UPNA team was fundend by the Spanish Agencia Estatal de Investigación (AEI) and Ministerio de Ciencia e Innovación (MCIN), the European Regional Development Fund (ERDF/FEDER), the European Union's NextGenerationEU funds for their financial support. In particular, this work was partially funded by the following research projects: TED2021-130846B-I00 (MULTIeFUEL project), PID2021-127265OB-C21 (SOLFUEL project), PLEC2022-009221 (Panel-toFuel project), PID2021-124572OB-C31.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Highly selective CO formation via CO2 hydrogenation over novel ceria-based high-entropy oxides (HEOs)

  • Cortázar, María
  • Lafuente Adiego, Marta
  • Navarro Puyuelo, Andrea
  • García, Xènia
  • Llorca Piqué, Jordi
  • Reyero Zaragoza, Inés
  • Bimbela Serrano, Fernando
  • Gandía Pascual, Luis
In the present study, new ceria-based high-entropy oxides (HEOs) were investigated as CO2 hydrogenation catalysts. The nominal composition was (Ce0.5Ni0.1Co0.1Cu0.1Zn0.1Mg0.1)Ox and the synthesis was accomplished through the citrate complexing sol-gel method. Characterization techniques utilized including ICP-AES, in situ XRD and in situ XPS, SEM-EDS, HR-TEM and HAADF-STEM, Raman spectroscopy, H2-TPR, CO2-TPD and N2 physical adsorption. The physicochemical characterization and the catalytic results revealed that the conditions of the thermal treatments at which the oxides were subjected critically determined the catalytic performance, especially the CO2 hydrogenation products selectivities. Calcination in air and/or reduction in hydrogen conducted at temperatures below 500 °C led to active but poorly selective catalysts that produced both methane and CO with significant yields. This was mainly attributed to the presence of metallic Cu, Ni and Co on the catalysts that appeared to be supported on ceria doped with the rest of the formulation elements. In contrast, thermal treatments at 750 °C favored the formation of a rocksalt entropy-stabilized (NiCoCuZnMg)Ox HEO supported on ceria that has stood out for showing an excellent selectivity towards the reverse water¿gas shift (RWGS) reaction. This catalyst led to CO selectivities of almost 100 % over a very wide range of reaction temperatures (300-700 °C). Long-term stability tests (100 h) showed only a slight decrease in CO2 conversion, while CO selectivity remained stable at nearly 100 % at 400 °C. XRD characterization of the used catalysts evidenced that, whereas the basic catalyst structure remained, some metallic copper exsolved during reduction and reaction period. These results are relevant and very promising, opening a door to the development of new catalysts for the valorization of CO2 through the RWGS reaction, thus expanding the low-temperature limit at which this process can be carried out selectively., Authors wish to thank the Spanish Agencia Estatal de Investigaci´on (AEI) and Ministerio de Ciencia e Innovaci´on (MCIN), the European Regional Development Fund (ERDF/FEDER), the European Union¿s NextGenerationEU funds for their financial support. In particular, this work was partially funded by the following research projects: TED2021- 130846B-I00 (MULTIeFUEL project), PID2021-127265OB-C21 (SOLFUEL project), PLEC2022-009221 (Panel-to-Fuel project), PID2021- 124572OB-C31, and CEX2023-001300-M. M. Cortazar and M. Lafuente also thank Ministerio de Universidades (Spain) and NextGenerationEU funds for their ¨Margarita Salas¨postdoctoral grants. JL is a Serra Húnter Fellow and is grateful to ICREA Academia program. Open access funding provided by Universidad Pública de Navarra.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Comparative study of supported Ni and Co catalysts prepared using the All-in-One method in the hydrogenation of CO2: effects of using (Poly)Vinyl Alcohol (PVA) as an additive

  • Navarrete Rodríguez, Luisa Fernanda
  • Atienza Martínez, María
  • Reyero Zaragoza, Inés
  • Urroz Unzueta, José Carlos
  • Amorrortu, Oihana
  • Sanz Iturralde, Oihane
  • Montes, Mario
  • Garcés, Siby I.
  • Bimbela Serrano, Fernando
  • Gandía Pascual, Luis
Two series of Ni and Co catalysts supported onto La-Al2O3 were prepared and the CO2 hydrogenation reactions investigated. The catalytic performance was evaluated in terms of the evolution with the reaction temperature of the CO2 conversion and product (CH4 and CO) yields, as well as specific activities (TOF) and apparent activation energies. CH4 was the favored product over both metals while the TOF for CH4 formation was about three times higher for Ni than Co at 240–265 °C. Metallic particle size effects were found, with the TOF for CH4 formation decreasing over both Ni and Co as the mean metallic size decreased. In contrast, the TOF for CO formation tended to increase at a decreasing particle size for the catalysts with the smallest Ni particle sizes. The apparent activation energies for Ni and Co were very similar and significantly decreased to values of 73–79 kJ/mol when the metallic dispersion increased. The catalysts were prepared using the all-in-one method, resulting in (poly)vinyl alcohol (PVA) being a key additive that allowed us to enhance the dispersion of Ni and Co to give very effective catalysts. This comparative study joins the few existing ones in the literature in which catalysts based on these metals operated under strictly the same reaction conditions., This research was funded by the Spanish Agencia Estatal de Investigación (AEI) and Ministerio de Ciencia e Innovación (MICINN), the European Union’s NextGenerationEU funds, the European Regional Development Fund (ERDF/FEDER) “Una manera de hacer Europa” and Plan de Recuperación, Transformación y Resiliencia, grant numbers PID2021-127265OB-C21, TED2021-130846B-I00 and PLEC2022-009221. This research was funded also by the University of the Basque Country, grant numbers COLLAB22/05 and GIU21/033.