Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 15
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microstructural control by freeze-casting of CaO architectures for improved and stable thermochemical energy storage performance

  • Ambhar, Nabil
  • Perejón, Antonio
  • Hanaor, Dorian
  • Gurlo, Aleksander
  • Ramírez-Rico, Joaquín
  • Pérez-Maqueda, Luis A.
  • Sánchez-Jimenez, Pedro E.
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
[EN] This study investigates the development of porous calcium-based monoliths via freeze-casting (FC) as a novel approach for thermochemical energy storage, particularly within the Calcium Looping (CaL) process. The freeze-casting technique enabled the fabrication of scaffolds with controlled porosity using polyvinyl alcohol (PVA) as a binder. Experimental results demonstrated that freeze-cast monoliths exhibited superior multicycle performance under various carbonation and calcination conditions. The FC-CaCO3 monolith achieved the highest residual conversion of 68.1 % under mild vacuum calcination conditions (780 °C, 0.1 bar CO2), significantly surpassing other configurations. Tests conducted in an inert atmosphere also yielded favorable results, with a conversion of 56.1 %, outperforming equivalent raw powder samples. The enhanced performance is attributed to improved CO2 interaction with the porous structure, mitigating sintering effects and preserving active surface area. Morphological observations by X-ray tomography and SEM confirmed limited particle sintering after multiple cycles, maintaining a reactive surface that supported consistent conversion rates. The pore size distribution of the material evolves upon cycling resulting in an increased microporosity, while the pore network maintains a low tortuosity (¿ ~ 1.5¿2.0). The addition of dopants such as ZrO2 and SiO2 did not enhance performance, as the monoliths' inherent structure provided sufficient stability. These findings highlight freeze-casting as a promising method for creating advanced porous materials suitable for energy storage applications., Financial support is acknowledged from grants TED2021-131839B-C22 and PDC2021-121552-C21 (MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR) and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe. PhD Fellowship granted to N. Amghar (PRE2018-085866) from the Spanish Government Agency Ministerio de Ciencia, Innovacion y Universidades. J. Ivorra-Martinez thanks Generalitat Valenciana-GVA for funding a postdoc position through the CIAPOS program co-funded by ESF Investing in your future, grant number CIAPOS/2023/362. XCT measurements were performed at the X-ray laboratory of the Research, Technology and Innovation Center (CITIUS) of the University of Seville.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

3D-printed mineral limestone structures for calcium looping thermochemical energy storage: reactivity and performance across cycles

  • Castro-Chincho, Ana
  • Perejón, Antonio
  • Sanchez-Jimenez, Pedro E.
  • Ramírez-Rico, Joaquín
  • Pérez-Maqueda, Luis A.
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
[EN] This work presents a proof of concept for the use of 3D-printed CaCO¿ structures, prepared from low-cost and widely available mineral limestone, as an innovative approach for thermochemical energy storage (TCES) via the calcium looping (CaL) process in a fixed-bed reactor. These structures offer significant advantages in terms of reaction efficiency, gas flow control, structural stability, and maintenance. These factors are critical for achieving uniform reaction surface distribution and effective thermal management. The 3D structures were fabricated by robocasting and subjected to various debinding and calcination conditions. They maintained their structural integrity and exhibited high reactivity over multiple carbonation-calcination cycles. Under scheme 1 conditions (calcinations in nitrogen), the printed structures retained a CaO conversion of 0.44 after 50 cycles, corresponding to an energy density of 1.39 MJ kg¿ 1 CaO, outperforming the powdered sample, which reached a conversion of 0.32. Advanced characterization techniques, including thermography, scanning electron microscopy, and X-ray computed tomography, highlight the internal structural advantages of the 3D structures. Overall, this study demonstrates the potential of 3D-printed CaCO¿ structures as scalable and efficient TCES materials, offering a promising route toward improving the performance and practical deployment of solid-state thermochemical energy storage systems., Financial support is acknowledged from grant TED2021-131839B-C22 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe. D.L. and J. I.-M. thank Generalitat Valenciana-GVA for funding their postdoc position through the CIAPOS program co-funded by ESF Investing in your future, grant numbers CIAPOS/2022/140 and CIAPOS/2023/362. Financial support provided by VII PPIT of the University of Seville for the use of the General Research Services (CITIUS) is acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ca-based materials derived from calcined cigarette butts for CO2 capture and thermochemical energy storage

  • Amghar, Nabil
  • Moreno-García, Virginia
  • Sanchez-Jimenez, Pedro Enrique
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
[EN] Cigarette butts (CBs) are one of the most common types of litter in the world. Due to the toxic substances they contain, the waste generated poses a harmful risk to the environment, and therefore there is an urgent need for alternative solutions to landfill storage. Thus, this work presents a possible revalorization of this waste material, which implies interesting environmental benefits. CBs were used as sacrificial templates for the preparation of CaO-based materials by impregnation with calcium and magnesium nitrates followed by flaming combustion. These materials presented enhanced porosity for their use in the Calcium Looping process applied either to thermochemical energy storage or CO2 capture applications. The influence of the concentration of Ca and Mg in the impregnating solutions on the multicycle reactivity of the samples was studied. An improved multicycle performance was obtained in terms of conversion for both applications. (c) 2023 The Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V., This work was supported by MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR (Nos. PDC2021-121552-C21 and PID2022-140815OB-C22) and Ministerio de Ciencia e Innovacion (No. TED2021-131839B-C22). Nabil Amghar acknowledges the Ph.D Fellowship grant from the Spanish Government Agency Ministerio de Ciencia, Innovacion y Universidades (No. PRE2018-085866) . Virginia Moreno wants to thank Generalitat Valenciana-GVA for funding a postdoc position through the APOSTD program co-funded by ESF Investing in your future (No. CIAPOS/2021/67) .
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of Long-Term CaO Storage Conditions on the Calcium Looping Thermochemical Reactivity

  • Amghar, Nabil
  • Perejón, Antonio
  • Ortiz, Carlos
  • Pérez Maqueda, Luis A
  • Sánchez-Jiménez, Pedro E.
Long-term storage capability is often claimed as one of the distinct advantages of the calcium looping process as a potential thermochemical energy storage system for integration into solar power plants. However, the influence of storage conditions on the looping performance has seldom been evaluated experimentally. The storage conditions must be carefully considered as any potential carbonation at the CaO storage tank would reduce the energy released during the subsequent carbonation, thereby penalizing the round-trip efficiency. From lab-scale to conceptual process engineering, this work considers the effects of storing solids at low temperatures (50-200 °C) in a CO2 atmosphere or at high temperatures (800 °C) in N2. Experimental results show that carbonation at temperatures below 200 °C is limited; thus, the solids could be stored during long times even in CO2. It is also demonstrated at the lab scale that the multicycle performance is not substantially altered by storing the solids at low temperatures (under CO2) or high temperatures (N2 atmosphere). From an overall process perspective, keeping solids at high temperatures leads to easier heat integration, a better plant efficiency (+2-4%), and a significantly higher energy density (+40-62%) than considering low-temperature storage. The smooth difference in the overall plant efficiency with the temperature suggests a proper long-term energy storage performance if adequate energy integration is carried out., This work has been funded by the grant TED2021-131839B-C22 (Ministerio de Ciencia e Innovación). Financial support from project PDC2021-121552-C21 (MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR) is also acknowledged. N. Amghar acknowledges the PhD Fellowship grant PRE2018-085866 from the Spanish Government Agency Ministerio de Ciencia, Innovación y Universidades., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural, Vibrational, and Magnetic Characterization of Orthoferrite LaFeO3 Ceramic Prepared by Reaction Flash Sintering

  • Manchón-Gordón, Alejandro F.
  • Sánchez-Jiménez, Pedro E.
  • Blázquez, Javier S.
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
LaFeO3 perovskite ceramics have been prepared via reaction flash technique using Fe2O3 and La2O3 as precursors. The obtained pellets have been investigated using several techniques. The formation of LaFeO3 has been clearly confirmed by X-ray diffraction. The scanning electron microscopy micrographs have shown the microporous character of the obtained pellets due to the low temperature and dwell time used in the synthesis process (10 min at 1173 K). The orthorhombic-rhombohedral phase transition has been observed at approximately 1273 K in differential thermal analysis measurements, which also allows us to determine the Néel temperature at 742 K. The fitted Mössbauer spectra exposed the presence of a single sextet ascribed to the Fe+3 ions in the tetrahedral site. Finally, magnetic measurements at room temperature indicate the antiferromagnetic character of the sample., This work has been funded by EU Next Generation funds and Spanish Ministry of Science and Innovation (projects TED2021-131839B-C22 and PDC2021-121552-C21) and by Junta de AndalucíaConsejería de Conocimiento, Investigación y Universidad (proyect ProyExcel_00360). A.F. ManchónGordón also acknowledges Grant FJC2021-047783-I funded by MCIN/AEI/10.13039/501100011033 and by “European Union NextGenerationEU/PRTR, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A generalized interface reaction kinetic model for describing heterogeneous processes driven by contracting mechanisms

  • Arcenegui-Troya, Juan J.
  • Sánchez-Jiménez, Pedro E.
  • Rodríguez-Laguna, María del Rocío
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
The correct determination of the kinetic model and the kinetic parameters that describe a heterogeneous process is key to accurately predicting its progress within a wide range of conditions, which is one of the main purposes of kinetic analysis. Albeit ideal kinetic models continue to be used to gain insight about the process mechanism, they are constrained by certain assumptions that are rarely met in real experiments and limit their applicability. This is the case of contracting (or interface) kinetic models, which are one of the most commonly used. Thus, the ideal kinetic model R2 is derived by assuming a cylindrical contraction in the radial direction but not contemplating the possibility of a contraction in the direction of the axis of the cylinder. Moreover, in the case of the ideal model R3, it is assumed that contraction takes place simultaneously in particles of identical dimensions in all three directions of space (spheres or cubes). Here, it is revisited this type of model, and it is considered the contraction of particles with different geometries, namely cylinders with different aspect ratios and rectangular cuboids. Besides, a novel generalized interface reaction model is proposed, which covers all the studied cases and broadens the range of applicability to more complex situations involving different geometries and inhomogeneous particle sizes. Finally, the proposed model is applied to the analysis of the experimental thermal dissociation of ammonium nitrate, previously described in the literature as a sublimation process. It is proved that the novel kinetic model provides a more accurate description of the kinetics of the reaction and better prediction capabilities., Financial support is acknowledged from grants TED2021-131839B-C22 and PDC2021-121552-C21 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by European Union NextGeneration EU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and ERDF A way of making Europe., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ca-based materials derived from calcined cigarette butts for CO2 capture and thermochemical energy storage

  • Amghar, Nabil
  • Moreno, Virginia
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
Cigarette butts (CBs) are one of the most common types of litter in the world. Due to the toxic substances they contain, the waste generated poses a harmful risk to the environment, and therefore there is an urgent need for alternative solutions to landfill storage. Thus, this work presents a possible revalorization of this waste material, which implies interesting environmental benefits. CBs were used as sacrificial templates for the preparation of CaO-based materials by impregnation with calcium and magnesium nitrates followed by flaming combustion. These materials presented enhanced porosity for their use in the Calcium Looping process applied either to thermochemical energy storage or CO capture applications. The influence of the concentration of Ca and Mg in the impregnating solutions on the multicycle reactivity of the samples was studied. An improved multicycle performance was obtained in terms of conversion for both applications., This work was supported by MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR (Nos. PDC2021-121552-C21 and PID2022-140815OB-C22) and Ministerio de Ciencia e Innovación (No. TED2021-131839B-C22). Nabil Amghar acknowledges the Ph.D Fellowship grant from the Spanish Government Agency Ministerio de Ciencia, Innovación y Universidades (No. PRE2018-085866). Virginia Moreno wants to thank Generalitat Valenciana-GVA for funding a postdoc position through the APOSTD program co-funded by ESF Investing in your future ( No. CIAPOS/2021/67)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sodium acetate-based thermochemical energy storage with low charging temperature and enhanced power density

  • Arcenegui-Troya, Juan J.
  • Lizana, Jesús
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
  • Vañes-Vallejo, A.
  • Pérez-Maqueda, Luis A.
The electrification of heat necessitates the development of innovative domestic heat batteries to effectively balance energy demand with renewable power supply. Thermochemical heat storage systems show great promise in supporting the electrification of heating, thanks to their high thermal energy storage density and minimal thermal losses. Among these systems, salt hydrate-based thermochemical systems are particularly appealing. However, they do suffer from slow hydration kinetics in the presence of steam, which limits the achievable power density. Additionally, their relatively high dehydration temperature hinders their application in supporting heating systems. Furthermore, there are still challenges regarding the appropriate thermodynamic, physical, kinetic, chemical, and economic requirements for implementing these systems in heating applications. This study analyzes a proposal for thermochemical energy storage based on the direct hydration of sodium acetate with liquid water. The proposed scheme satisfies numerous requirements for heating applications. By directly adding liquid water to the salt, an unprecedented power density of 5.96 W/g is achieved, nearly two orders of magnitude higher than previously reported for other salt-based systems that utilize steam. Albeit the reactivity drops as a consequence of deliquescence and particle aggregation, it has been shown that this deactivation can be effectively mitigated by incorporating 10 % silica, achieving lower but stable energy and power density values. Furthermore, unlike other salts studied previously, sodium acetate can be fully dehydrated at temperatures within the ideal range for electrified heating systems such as heat pumps (40 °C – 60 °C). The performance of the proposed scheme in terms of dehydration, hydration, and multicyclic behavior is determined through experimental analysis., This work was supported by MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR (Nos. PDC2021-121552-C21 and PID2022-140815OB-C22) and Ministerio de Ciencia e Innovación (No. TED2021-131839B-C22)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of the atmosphere on the formation of high-entropy oxides within the Co–Cu–Fe–Mg–Mn–Ni–O system via reactive flash sintering

  • Manchón-Gordón, Alejandro F.
  • Lobo Llamas, C.
  • Molina Molina, S.
  • Perejón, Antonio
  • Sánchez-Jiménez, Pedro E.
  • Pérez-Maqueda, Luis A.
In this study, the feasibility of preparing quinary equimolar high-entropy oxides within the Co–Cu–Fe–Mg–Mn–Ni–O system was explored using the reactive flash sintering (RFS) technique. Various compositions were tested using this technique under atmosphere pressure, leading to the formation of two primary phases: rock-salt and spinel. Conversely, a new high-entropy oxide was produced as a single-phase material with the composition (Co0.2,Cu0.2,Mg0.2,Mn0.2,Ni0.2)O when RFS experiments were conducted in nitrogen atmosphere. The reducing conditions achieved in nitrogen enabled the incorporation of cations with oxidation states different from +2 into the rock-salt lattice, emphasizing the critical role of the processing atmosphere, whether inert or oxidizing, in the formation of high-entropy oxides. The electrical characterization of this material was obtained via impedance spectroscopy, exhibiting a homogeneous response attributed to electronic conduction with a temperature dependence characteristic of disordered systems., This research has received funding from the Junta de Andalucía-Consejería de Universidad, Investigación e Innovación under the ProyExcel_00360 project. Financial support is also acknowledged from the grant TED2021-131839B–C22 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Unlocking synergistic benefits of the calcium looping-calcium hydroxide integration for energy storage: A perspective on sorbent performance

  • Arcenegui Troya, Juan
  • Carro, Andrés
  • Ortiz, Carlos
  • Chacartegui, Ricardo
  • Perejón, Antonio
  • Pérez Maqueda, Luis A
  • Sánchez-Jiménez, Pedro E.
Calcium Looping has recently attracted attention as a high temperature thermochemical energy storage system. However, significant sintering due to the high temperatures hampers the recyclability of CaO. Hydration and hydroxylation has been explored as a method to regenerate the spent CaO. This study investigates a novel synergistic integration of carbonation (CaCO3/CaO) and hydroxylation (CaO/Ca(OH)2) reactions. Calcination was conducted in N2 and N2/H2O mixtures with 29 % steam content. Carbonation was conducted in CO2/H2O mixture with similar steam concentrations. Results show that steam plays a dual role: during calcination, it promotes the formation of large pores on the CaO surface, and during carbonation, it enhances mineralization, resulting in larger CaCO3 grains. Also, steam promotes CO2 diffusion through the CaCO3 layer and, at the same time, significantly mitigates the deactivation of CaO along the cycles. Specifically, sequential calcination/carbonation cycles without steam yield a residual conversion value of 0.14. Steam injection improved residual conversion to 0.27. Alternatively, the interleaving of hydroxylation/dehydroxylation cycles in the sequence further increased this value to 0.64 without steam and up to 0.76 with steam injection. Hydroxylation/dehydroxylation cycles alone demonstrated high stability, with a residual conversion of 0.98 when interleaved with calcination/carbonation cycles under 29 % steam conditions. Additionally, frequent hydroxylation/dehydroxylation cycles improve overall conversion stability, highlighting their synergistic benefits within the integrated process. This work underscores the potential of integrating Calcium Looping with Calcium Hydroxide for improved multicycle performance and opens pathways for scaling experiments to pilot systems, alongside assessing the efficiency and economic viability of this integrated approach., Financial support is acknowledged from grants TED2021-131839B-C22 and PDC2021-121552-C21 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnesium calcites for CO2 capture and thermochemical energy storage using the calcium-looping process

  • Perejón, Antonio
  • Arcenegui-Troya, Juan
  • Sánchez-Jiménez, Pedro E.
  • Diánez, María Jesús
  • Pérez-Maqueda, Luis A.
Chemicals and CAS Registry Numbers calcium 7440-70-2, 14092-94-5 calcium carbonate 13397-26-7, 13701-58-1, 14791-73-2, 471-34-1 carbon dioxide 124-38-9, 58561-67-4 magnesium 7439-95-4 magnesium oxide 1309-48-4, 1317-74-4 Calcium Calcium Carbonate Carbon Dioxide Magnesium Magnesium Oxide, In this study, a precipitation-based synthesis method has been employed to prepare magnesium calcites with the general formula Ca1-xMgxCO3, with the objective of use them in the calcium looping (CaL) process for CO2 capture (CaL-CCS) and thermochemical energy storage (CaL-CSP). The structure and microstructure of the samples have been characterized. It has been found by X-ray diffraction that the samples with a Ca:Mg molar ratio of 0.5:0.5 and 0.55:0.45 are phase pure, while the samples with molar ratios of 0.7:0.3 and 0.8:0.2 are composed by two phases with different stoichiometry. In addition, the sample prepared with calcium alone shows the aragonite phase. The microstructure of the magnesium-containing samples is composed of nanocrystals, which are aggregated in spherical particles whereas the aragonite sample presents a typical rod-like morphology. The multicycle tests carried out under CaL-CCS conditions show that an increase on the MgO content in the calcined samples results in a reduced value of effective conversion when compared to aragonite. On the other hand, under CaL-CSP conditions, the samples with the higher MgO content exhibit nearly stable effective conversion values around 0.5 after 20 cycles, which improve the results obtained for aragonite and those reported for natural dolomite tested under the same conditions., Financial support is acknowledged from grants TED2021-131839B–C22 and PDC2021-121552-C21 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructural control by freeze-casting of CaO architectures for improved and stable thermochemical energy storage performance

  • Amghar, Nabil
  • Ivorra-Martínez, Juan
  • Perejón, Antonio
  • Hanaor, Dorian
  • Gurlo, Aleksander
  • Ramírez-Rico, Joaquín
  • Pérez-Maqueda, Luis A.
  • Sánchez-Jiménez, Pedro E.
This study investigates the development of porous calcium-based monoliths via freeze-casting (FC) as a novel approach for thermochemical energy storage, particularly within the Calcium Looping (CaL) process. The freeze-casting technique enabled the fabrication of scaffolds with controlled porosity using polyvinyl alcohol (PVA) as a binder. Experimental results demonstrated that freeze-cast monoliths exhibited superior multicycle performance under various carbonation and calcination conditions. The FC-CaCO<inf>3</inf> monolith achieved the highest residual conversion of 68.1 % under mild vacuum calcination conditions (780 °C, 0.1 bar CO<inf>2</inf>), significantly surpassing other configurations. Tests conducted in an inert atmosphere also yielded favorable results, with a conversion of 56.1 %, outperforming equivalent raw powder samples. The enhanced performance is attributed to improved CO<inf>2</inf> interaction with the porous structure, mitigating sintering effects and preserving active surface area. Morphological observations by X-ray tomography and SEM confirmed limited particle sintering after multiple cycles, maintaining a reactive surface that supported consistent conversion rates. The pore size distribution of the material evolves upon cycling resulting in an increased microporosity, while the pore network maintains a low tortuosity (τ ~ 1.5–2.0). The addition of dopants such as ZrO<inf>2</inf> and SiO<inf>2</inf> did not enhance performance, as the monoliths' inherent structure provided sufficient stability. These findings highlight freeze-casting as a promising method for creating advanced porous materials suitable for energy storage applications., Financial support is acknowledged from grants TED2021-131839B-C22 and PDC2021-121552-C21 (MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR) and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe. PhD Fellowship granted to N. Amghar (PRE2018-085866) from the Spanish Government Agency Ministerio de Ciencia, Innovación y Universidades. J. Ivorra-Martinez thanks Generalitat Valenciana - GVA for funding a postdoc position through the CIAPOS program co-funded by ESF Investing in your future, grant number CIAPOS/2023/362. XCT measurements were performed at the X-ray laboratory of the Research, Technology and Innovation Center (CITIUS) of the University of Seville., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Enhancing the Multicycle Performance of SrCO₃-Based Thermochemical Energy Storage Using SnO2

  • Santamaria Padilla, Adriana
  • Romero-Paredes Rubio, Hernando
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
This work investigates the potential of strontium carbonate (SrCO3) as a thermochemical energy storage (TCES) material and explores the incorporation of tin (IV) oxide (SnO2) as a chemical spacer to enhance its multicycle performance. High-purity SrCO3 and SnO2 were used to prepare composites with various mass proportions. The composites were subjected to repeated calcination/carbonation cycles under controlled conditions. Experimental results indicate that pure SrCO3 achieves a high initial effective conversion at 900 °C; however, its performance degrades significantly over successive cycles. In contrast, the SrCO3/SnO2 composite containing 15 wt% SnO2 (SrSnO15) maintained a stable effective conversion compared to a drop to 0.11 in pure SrCO3 by the ninth cycle. Structural characterization using X-ray diffraction and scanning electron microscopy revealed the formation of secondary phases, including strontium stannate (SrSnO3) and a spinel phase (Sr2SnO4), which impact the reactivity of the material. Additionally, a pressure swing approach was applied to reduce the calcination temperature, which improved the effective conversion during initial cycles by delaying spinel formation; however, its benefits diminished over extended cycling. Comparative analysis with literature data underscores the promising performance of the SrSnO15 composite. Overall, the results demonstrate that SnO2 addition enhances the long-term cyclic stability and energy storage capacity of SrCO3-based TCES systems, paving the way for more efficient and durable renewable energy storage solutions., The authors acknowledge the financial support received through CONAHCYT as part of the Call for Basic and Frontier Science 2023-2024 within Strategic Project No. CBF2023-2024-3410, entitled "Development of Advanced Methods and New Materials for Solar Thermal Energy Storage Using Reversible Solid-Gas Reaction Cycles to Enhance the Use of Solar Technology," which enabled the development of research and support of human resource training at the graduate level. Financial support is also acknowledged from grants TED2021-131839B–C22 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe. The authors acknowledge the financial support received through the support scholarship by CONAHCYT with number 814358., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Datos de investigación Set de datos (Dataset)

Dataset for the paper "Enhancing Calcium-Looping Materials for Thermochemical Energy Storage: Alkali Chloride Modification for Improved Cycling Stability and Moisture Resistance"

  • Robles-Solano, Esther
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
  • Sánchez-Jiménez, Pedro E.
This study explores the impact of alkali chloride additives on the performance and durability of CaO-based materials obtained from natural limestone for thermochemical energy storage through the calcium-looping process. The investigation was carried out using CaCO3 of different particle sizes derived from natural limestone as the base material. An alkali mixture, extracted from biomass ash and predominantly composed of KCl, was used as additive. The composite materials were prepared in varying proportions (1 and 5 wt%) and tested in thermal cycling experiments that simulate energy storage operation conditions, in order to assess their multicycle reactivity and storage behavior. Key experimental findings demonstrate that a limited alkali addition (1 wt%) slightly decreases conversion during the fast carbonation stage but significantly enhances multicycle stability, achieving conversion values up to 0.40 after 20 cycles for fine particles (60-100 µm) compared to 0.25-0.30 for unmodified materials. This improvement is attributed to accelerated diffusion-controlled carbonation. Furthermore, the use of alkaline salts has a positive effect on inter-cycle storage stability by preventing moisture-induced degradation, as the salts inhibit hydroxylation of CaO under humid conditions, which would otherwise reduce the stored energy. Thus, it has been observed that alkali modification extends the time to full conversion to Ca(OH)2 by up to 700% under 32% relative humidity conditions. The optimized composition (1 wt% alkali) effectively balances conversion efficiency, cyclic and storage stability, making this approach particularly viable for industrial energy storage applications such as concentrated solar power systems where materials may undergo extended storage periods between operational cycles., MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR: TED2021-131839B-C22; MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe: PID2022-140815OB-C22, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

3D-printed mineral limestone structures for calcium looping thermochemical energy storage: reactivity and performance across cycles

  • Castro-Chincho, Ana
  • Ivorra-Martinez, Juan
  • Perejón, Antonio
  • Sánchez-Jiménez, Pedro E.
  • Lascano, Diego
  • Ramírez-Rico, J.
  • Pérez-Maqueda, Luis A.
This work presents a proof of concept for the use of 3D-printed CaCO₃ structures, prepared from low-cost and widely available mineral limestone, as an innovative approach for thermochemical energy storage (TCES) via the calcium looping (CaL) process in a fixed-bed reactor. These structures offer significant advantages in terms of reaction efficiency, gas flow control, structural stability, and maintenance. These factors are critical for achieving uniform reaction surface distribution and effective thermal management. The 3D structures were fabricated by robocasting and subjected to various debinding and calcination conditions. They maintained their structural integrity and exhibited high reactivity over multiple carbonation-calcination cycles. Under scheme 1 conditions (calcinations in nitrogen), the printed structures retained a CaO conversion of 0.44 after 50 cycles, corresponding to an energy density of 1.39 MJ kg−1 CaO, outperforming the powdered sample, which reached a conversion of 0.32. Advanced characterization techniques, including thermography, scanning electron microscopy, and X-ray computed tomography, highlight the internal structural advantages of the 3D structures. Overall, this study demonstrates the potential of 3D-printed CaCO₃ structures as scalable and efficient TCES materials, offering a promising route toward improving the performance and practical deployment of solid-state thermochemical energy storage systems., Financial support is acknowledged from grant TED2021-131839B-C22 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe. D.L. and J. I.-M. thank Generalitat Valenciana - GVA for funding their postdoc position through the CIAPOS program co-funded by ESF Investing in your future, grant numbers CIAPOS/2022/140 and CIAPOS/2023/362. Financial support provided by VII PPIT of the University of Seville for the use of the General Research Services (CITIUS) is acknowledged., Peer reviewed