Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 16
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Microstructural control by freeze-casting of CaO architectures for improved and stable thermochemical energy storage performance

  • Ambhar, Nabil
  • Perejón, Antonio
  • Hanaor, Dorian
  • Gurlo, Aleksander
  • Ramírez-Rico, Joaquín
  • Pérez-Maqueda, Luis A.
  • Sánchez-Jimenez, Pedro E.
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
[EN] This study investigates the development of porous calcium-based monoliths via freeze-casting (FC) as a novel approach for thermochemical energy storage, particularly within the Calcium Looping (CaL) process. The freeze-casting technique enabled the fabrication of scaffolds with controlled porosity using polyvinyl alcohol (PVA) as a binder. Experimental results demonstrated that freeze-cast monoliths exhibited superior multicycle performance under various carbonation and calcination conditions. The FC-CaCO3 monolith achieved the highest residual conversion of 68.1 % under mild vacuum calcination conditions (780 °C, 0.1 bar CO2), significantly surpassing other configurations. Tests conducted in an inert atmosphere also yielded favorable results, with a conversion of 56.1 %, outperforming equivalent raw powder samples. The enhanced performance is attributed to improved CO2 interaction with the porous structure, mitigating sintering effects and preserving active surface area. Morphological observations by X-ray tomography and SEM confirmed limited particle sintering after multiple cycles, maintaining a reactive surface that supported consistent conversion rates. The pore size distribution of the material evolves upon cycling resulting in an increased microporosity, while the pore network maintains a low tortuosity (¿ ~ 1.5¿2.0). The addition of dopants such as ZrO2 and SiO2 did not enhance performance, as the monoliths' inherent structure provided sufficient stability. These findings highlight freeze-casting as a promising method for creating advanced porous materials suitable for energy storage applications., Financial support is acknowledged from grants TED2021-131839B-C22 and PDC2021-121552-C21 (MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR) and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe. PhD Fellowship granted to N. Amghar (PRE2018-085866) from the Spanish Government Agency Ministerio de Ciencia, Innovacion y Universidades. J. Ivorra-Martinez thanks Generalitat Valenciana-GVA for funding a postdoc position through the CIAPOS program co-funded by ESF Investing in your future, grant number CIAPOS/2023/362. XCT measurements were performed at the X-ray laboratory of the Research, Technology and Innovation Center (CITIUS) of the University of Seville.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publicación Artículo científico (JournalArticle)

Ca-based materials derived from calcined cigarette butts for CO2 capture and thermochemical energy storage

  • Amghar, Nabil
  • Moreno-García, Virginia
  • Sanchez-Jimenez, Pedro Enrique
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
[EN] Cigarette butts (CBs) are one of the most common types of litter in the world. Due to the toxic substances they contain, the waste generated poses a harmful risk to the environment, and therefore there is an urgent need for alternative solutions to landfill storage. Thus, this work presents a possible revalorization of this waste material, which implies interesting environmental benefits. CBs were used as sacrificial templates for the preparation of CaO-based materials by impregnation with calcium and magnesium nitrates followed by flaming combustion. These materials presented enhanced porosity for their use in the Calcium Looping process applied either to thermochemical energy storage or CO2 capture applications. The influence of the concentration of Ca and Mg in the impregnating solutions on the multicycle reactivity of the samples was studied. An improved multicycle performance was obtained in terms of conversion for both applications. (c) 2023 The Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V., This work was supported by MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR (Nos. PDC2021-121552-C21 and PID2022-140815OB-C22) and Ministerio de Ciencia e Innovacion (No. TED2021-131839B-C22). Nabil Amghar acknowledges the Ph.D Fellowship grant from the Spanish Government Agency Ministerio de Ciencia, Innovacion y Universidades (No. PRE2018-085866) . Virginia Moreno wants to thank Generalitat Valenciana-GVA for funding a postdoc position through the APOSTD program co-funded by ESF Investing in your future (No. CIAPOS/2021/67) .
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Influence of Long-Term CaO Storage Conditions on the Calcium Looping Thermochemical Reactivity

  • Amghar, Nabil
  • Perejón, Antonio
  • Ortiz, Carlos
  • Pérez Maqueda, Luis A
  • Sánchez-Jiménez, Pedro E.
Long-term storage capability is often claimed as one of the distinct advantages of the calcium looping process as a potential thermochemical energy storage system for integration into solar power plants. However, the influence of storage conditions on the looping performance has seldom been evaluated experimentally. The storage conditions must be carefully considered as any potential carbonation at the CaO storage tank would reduce the energy released during the subsequent carbonation, thereby penalizing the round-trip efficiency. From lab-scale to conceptual process engineering, this work considers the effects of storing solids at low temperatures (50-200 °C) in a CO2 atmosphere or at high temperatures (800 °C) in N2. Experimental results show that carbonation at temperatures below 200 °C is limited; thus, the solids could be stored during long times even in CO2. It is also demonstrated at the lab scale that the multicycle performance is not substantially altered by storing the solids at low temperatures (under CO2) or high temperatures (N2 atmosphere). From an overall process perspective, keeping solids at high temperatures leads to easier heat integration, a better plant efficiency (+2-4%), and a significantly higher energy density (+40-62%) than considering low-temperature storage. The smooth difference in the overall plant efficiency with the temperature suggests a proper long-term energy storage performance if adequate energy integration is carried out., This work has been funded by the grant TED2021-131839B-C22 (Ministerio de Ciencia e Innovación). Financial support from project PDC2021-121552-C21 (MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR) is also acknowledged. N. Amghar acknowledges the PhD Fellowship grant PRE2018-085866 from the Spanish Government Agency Ministerio de Ciencia, Innovación y Universidades., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Direct comparison of surface crystal growth kinetics in chalcogenide glass measured by microscopy and DSC

  • Shánělová, Jana
  • Honcová, Pavla
  • Málek, Jiří
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
Surface crystallization in fine powder Se70Te30 chalcogenide glass was studied by differential scanning calorimetry (DSC) and optical microscopy. A complex kinetic analysis of these experimental data reveals that the contracting sphere mechanism (R3 model) is the rate determining step of crystal growth, and the conventional Johnson–Mehl–Avrami–Kolmogorov model cannot be used in this case. Moreover, it is clearly shown that the particle size distribution should be considered in crystallization studies. Actually, when the particle size effect is taken into account, the simulated DSC curves for the R3 model agree very well with the experimental data over the entire temperature range. The crystallization kinetics determined from the nonisothermal DSC data are consistent with previously reported isothermal crystallization data for the same powder fraction. The crystal growth rate calculated from isothermal and nonisothermal DSC data agrees very well with the microscopically measured surface and bulk crystal growth rate., This work was supported by the Selected Research Teams Program of the Faculty of Chemical Technology, University of Pardubice. The authors thank Petr Pilný for providing the OriTas software, which was used for some of the kinetic calculations. The research grant PDC2021-121552-C21 (MCIN/AEI/10.13039/501100011033 and the European Union Next Generation grant EU/PRTR) is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Thermochemical energy storage using calcium magnesium acetates under low CO2 pressure conditions

  • Amghar, Nabil
  • Sánchez-Jiménez, Pedro E.
  • Pérez-Maqueda, Luis A.
  • Perejón, Antonio
The calcium looping multicycle performance of CaO-based materials, derived from calcium magnesium acetates with different Mg content were tested under experimental conditions compatible with thermochemical energy storage. In order to reduce the sintering-induced decay in performance, calcination at an absolute CO2 pressure of 0.1 bar and 0.01 bar is implemented. CaO carbonation is performed at standard 1 bar CO2 conditions. The samples can be fully calcined in short residence times. Samples with MgO present high cycling stability, even when the MgO content is as low as 5 mol%. The effective conversion values lie within the range 0.88–0.84 over ten calcination/carbonation cycles, which provides an accumulated energy storage density of 90.9 GJ/m3. This outstanding reactivity is related with the microstructure of the sample after calcination composed of CaO nanoparticles that are highly reactive for carbonation., This work has been funded by EU Next Generation funds and Spanish Ministry of Science and Innovation (projects TED2021-131839B-C22 and PDC2021-121552-C21), and by the grant CTQ2017-83602-C2-1-R (MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe by the European Union)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Structural, Vibrational, and Magnetic Characterization of Orthoferrite LaFeO3 Ceramic Prepared by Reaction Flash Sintering

  • Manchón-Gordón, Alejandro F.
  • Sánchez-Jiménez, Pedro E.
  • Blázquez, Javier S.
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
LaFeO3 perovskite ceramics have been prepared via reaction flash technique using Fe2O3 and La2O3 as precursors. The obtained pellets have been investigated using several techniques. The formation of LaFeO3 has been clearly confirmed by X-ray diffraction. The scanning electron microscopy micrographs have shown the microporous character of the obtained pellets due to the low temperature and dwell time used in the synthesis process (10 min at 1173 K). The orthorhombic-rhombohedral phase transition has been observed at approximately 1273 K in differential thermal analysis measurements, which also allows us to determine the Néel temperature at 742 K. The fitted Mössbauer spectra exposed the presence of a single sextet ascribed to the Fe+3 ions in the tetrahedral site. Finally, magnetic measurements at room temperature indicate the antiferromagnetic character of the sample., This work has been funded by EU Next Generation funds and Spanish Ministry of Science and Innovation (projects TED2021-131839B-C22 and PDC2021-121552-C21) and by Junta de AndalucíaConsejería de Conocimiento, Investigación y Universidad (proyect ProyExcel_00360). A.F. ManchónGordón also acknowledges Grant FJC2021-047783-I funded by MCIN/AEI/10.13039/501100011033 and by “European Union NextGenerationEU/PRTR, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Touch-free reactive flash sintering of dense strontium hexaferrite permanent magnet

  • Jalali, Syed I.A.
  • Manchón-Gordón, Alejandro F.
  • Chacartegui, Ricardo
  • Sánchez-Jiménez, Pedro E.
  • Blázquez, Javier S.
  • Perejón, Antonio
  • Raj, Rishi
  • Pérez-Maqueda, Luis A.
This work presents an extension of the touch-free flash sintering technique. In the proposed technique, chemical reaction and sintering occur in a single step, without the use of electrodes, in the presence of electric and magnetic fields. We show that a dense, single-phase strontium hexaferrite magnet can be produced from a mixture of commercial carbonate and oxide powders in a single step in a little more than a minute. This new technique implies significant reduction in energy and time consumption (primarily because of ultrafast processing) relative to conventional sintering., This work was funded by EU Next Generation funds and/or the Spanish Ministry of Science and Innovation (grants TED2021-131839B-C22, PDC2021-121552-C21, and PID2022-140815OB-C22). Financial support received from Junta de Andalucía-Consejería de Transformación Económica, Industria, Conocimiento y Universidades (ProyExcel_00360) is also acknowledged. RR is grateful to the Office of Naval Research for supporting this research under the grant N00014-18-1-2270. RC acknowledges support from Fulbright Association (grant number PRX21/00434) for supporting his visit to Boulder., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Flexible Kinetic Model Determination of Reactions in Materials under Isothermal Conditions

  • Arcenegui-Troya, Juan
  • Perejón, Antonio
  • Sánchez-Jiménez, Pedro E.
  • Pérez-Maqueda, Luis A.
Kinetic analysis remains a powerful tool for studying a large variety of reactions, which lies at the core of material science and industry. It aims at obtaining the kinetic parameters and model that best describe a given process and using that information to make reliable predictions in a wide range of conditions. Nonetheless, kinetic analysis often relies on mathematical models derived assuming ideal conditions that are not necessarily met in real processes. The existence of nonideal conditions causes large modifications to the functional form of kinetic models. Therefore, in many cases, experimental data hardly obey any of these ideal models. In this work, we present a novel method for the analysis of integral data obtained under isothermal conditions without any type of assumption about the kinetic model. The method is valid both for processes that follow and for those that do not follow ideal kinetic models. It consists of using a general kinetic equation to find the functional form of the kinetic model via numerical integration and optimization. The procedure has been tested both with simulated data affected by nonuniform particle size and experimental data corresponding to the pyrolysis of ethylene-propylene-diene., This work has been funded by EU Next Generation funds and the Spanish Ministry of Science and Innovation: grants TED2021-131839B-C22 and PDC2021-121552-C21. Financial support received from Junta de Andalucía-Consejería de Economía, Conocimiento, Empresas y Universidad via a postdoctoral fellowship with reference DOC_00044 is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Partial oxycombustion-calcium looping hybridisation for CO2 capture in waste-to-energy power plants

  • Ortiz, C.
  • García-Luna, S.
  • Chacartegui, Ricardo
  • Valverde, J. M.
  • Pérez-Maqueda, Luis A.
Integrating bioenergy and carbon capture and storage (BECCS) presents a great opportunity for power production with negative global CO2 emissions. This work explores a novel synergetic system that integrates membranes, partial biomass oxycombustion and the calcium looping (CaL) process. Polymeric membranes generate oxygen-enriched air (OEA) with an O2 concentration of 39%v/v, which is used for partial oxycombustion of biomass waste. The CO2-enriched flue gas evolves from the waste-to-energy plant to the CaL unit, where CO2 concentration is increased up to 90–95%v/v, ready for purification and sequestration. Compared to only oxycombustion systems, the proposed concept presents fewer technological challenges in retrofitting boilers to waste-to-energy plants. Moreover, this new approach is highly efficient as integrating membranes to produce OEA instead of cryogenic distillation systems significantly reduces energy consumption. A novel integration concept is modelled to evaluate the whole process efficiency and the effect of key parameters on the system performance, such as the temperature of the reactors, the membrane surface area, and the partial oxy-combustion degree. The results show that the so-called mOxy-CaL system has an energy consumption associated with CO2 capture below 4 MJ/kg CO2 (a 31% lower than that for a conventional CaL process), with a higher CO2 capture efficiency than oxycombustion and the CaL process separately. On the other hand, the economic analysis shows a higher CO2 capture cost for the novel configuration than for the typical CaL configuration due to the additional investment cost of the membrane system. Improvements in membrane performance by increasing its permeance and diminishing the required surface area would significantly reduce the economic cost of this novel integration. Using membranes with permeance over 400 GPU would boost the system's competitiveness., The research leading to these results has received funding from the Junta de Andalucía (grant number PY20 RE007). This work was also supported by ERDF A way of making Europe by the European Union), grant PDC2021-121552-C21 and PDC2021-121552-C22., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A generalized interface reaction kinetic model for describing heterogeneous processes driven by contracting mechanisms

  • Arcenegui-Troya, Juan J.
  • Sánchez-Jiménez, Pedro E.
  • Rodríguez-Laguna, María del Rocío
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
The correct determination of the kinetic model and the kinetic parameters that describe a heterogeneous process is key to accurately predicting its progress within a wide range of conditions, which is one of the main purposes of kinetic analysis. Albeit ideal kinetic models continue to be used to gain insight about the process mechanism, they are constrained by certain assumptions that are rarely met in real experiments and limit their applicability. This is the case of contracting (or interface) kinetic models, which are one of the most commonly used. Thus, the ideal kinetic model R2 is derived by assuming a cylindrical contraction in the radial direction but not contemplating the possibility of a contraction in the direction of the axis of the cylinder. Moreover, in the case of the ideal model R3, it is assumed that contraction takes place simultaneously in particles of identical dimensions in all three directions of space (spheres or cubes). Here, it is revisited this type of model, and it is considered the contraction of particles with different geometries, namely cylinders with different aspect ratios and rectangular cuboids. Besides, a novel generalized interface reaction model is proposed, which covers all the studied cases and broadens the range of applicability to more complex situations involving different geometries and inhomogeneous particle sizes. Finally, the proposed model is applied to the analysis of the experimental thermal dissociation of ammonium nitrate, previously described in the literature as a sublimation process. It is proved that the novel kinetic model provides a more accurate description of the kinetics of the reaction and better prediction capabilities., Financial support is acknowledged from grants TED2021-131839B-C22 and PDC2021-121552-C21 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and by European Union NextGeneration EU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/https://doi.org/10.13039/501100011033 and ERDF A way of making Europe., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Ca-based materials derived from calcined cigarette butts for CO2 capture and thermochemical energy storage

  • Amghar, Nabil
  • Moreno, Virginia
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
Cigarette butts (CBs) are one of the most common types of litter in the world. Due to the toxic substances they contain, the waste generated poses a harmful risk to the environment, and therefore there is an urgent need for alternative solutions to landfill storage. Thus, this work presents a possible revalorization of this waste material, which implies interesting environmental benefits. CBs were used as sacrificial templates for the preparation of CaO-based materials by impregnation with calcium and magnesium nitrates followed by flaming combustion. These materials presented enhanced porosity for their use in the Calcium Looping process applied either to thermochemical energy storage or CO capture applications. The influence of the concentration of Ca and Mg in the impregnating solutions on the multicycle reactivity of the samples was studied. An improved multicycle performance was obtained in terms of conversion for both applications., This work was supported by MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR (Nos. PDC2021-121552-C21 and PID2022-140815OB-C22) and Ministerio de Ciencia e Innovación (No. TED2021-131839B-C22). Nabil Amghar acknowledges the Ph.D Fellowship grant from the Spanish Government Agency Ministerio de Ciencia, Innovación y Universidades (No. PRE2018-085866). Virginia Moreno wants to thank Generalitat Valenciana-GVA for funding a postdoc position through the APOSTD program co-funded by ESF Investing in your future ( No. CIAPOS/2021/67)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Sodium acetate-based thermochemical energy storage with low charging temperature and enhanced power density

  • Arcenegui-Troya, Juan J.
  • Lizana, Jesús
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
  • Vañes-Vallejo, A.
  • Pérez-Maqueda, Luis A.
The electrification of heat necessitates the development of innovative domestic heat batteries to effectively balance energy demand with renewable power supply. Thermochemical heat storage systems show great promise in supporting the electrification of heating, thanks to their high thermal energy storage density and minimal thermal losses. Among these systems, salt hydrate-based thermochemical systems are particularly appealing. However, they do suffer from slow hydration kinetics in the presence of steam, which limits the achievable power density. Additionally, their relatively high dehydration temperature hinders their application in supporting heating systems. Furthermore, there are still challenges regarding the appropriate thermodynamic, physical, kinetic, chemical, and economic requirements for implementing these systems in heating applications. This study analyzes a proposal for thermochemical energy storage based on the direct hydration of sodium acetate with liquid water. The proposed scheme satisfies numerous requirements for heating applications. By directly adding liquid water to the salt, an unprecedented power density of 5.96 W/g is achieved, nearly two orders of magnitude higher than previously reported for other salt-based systems that utilize steam. Albeit the reactivity drops as a consequence of deliquescence and particle aggregation, it has been shown that this deactivation can be effectively mitigated by incorporating 10 % silica, achieving lower but stable energy and power density values. Furthermore, unlike other salts studied previously, sodium acetate can be fully dehydrated at temperatures within the ideal range for electrified heating systems such as heat pumps (40 °C – 60 °C). The performance of the proposed scheme in terms of dehydration, hydration, and multicyclic behavior is determined through experimental analysis., This work was supported by MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR (Nos. PDC2021-121552-C21 and PID2022-140815OB-C22) and Ministerio de Ciencia e Innovación (No. TED2021-131839B-C22)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Otros (Other)

Unlocking synergistic benefits of the calcium looping-calcium hydroxide integration for energy storage: A perspective on sorbent performance

  • Arcenegui Troya, Juan
  • Carro, Andrés
  • Ortiz, Carlos
  • Chacartegui, Ricardo
  • Perejón, Antonio
  • Pérez Maqueda, Luis A
  • Sánchez-Jiménez, Pedro E.
Calcium Looping has recently attracted attention as a high temperature thermochemical energy storage system. However, significant sintering due to the high temperatures hampers the recyclability of CaO. Hydration and hydroxylation has been explored as a method to regenerate the spent CaO. This study investigates a novel synergistic integration of carbonation (CaCO3/CaO) and hydroxylation (CaO/Ca(OH)2) reactions. Calcination was conducted in N2 and N2/H2O mixtures with 29 % steam content. Carbonation was conducted in CO2/H2O mixture with similar steam concentrations. Results show that steam plays a dual role: during calcination, it promotes the formation of large pores on the CaO surface, and during carbonation, it enhances mineralization, resulting in larger CaCO3 grains. Also, steam promotes CO2 diffusion through the CaCO3 layer and, at the same time, significantly mitigates the deactivation of CaO along the cycles. Specifically, sequential calcination/carbonation cycles without steam yield a residual conversion value of 0.14. Steam injection improved residual conversion to 0.27. Alternatively, the interleaving of hydroxylation/dehydroxylation cycles in the sequence further increased this value to 0.64 without steam and up to 0.76 with steam injection. Hydroxylation/dehydroxylation cycles alone demonstrated high stability, with a residual conversion of 0.98 when interleaved with calcination/carbonation cycles under 29 % steam conditions. Additionally, frequent hydroxylation/dehydroxylation cycles improve overall conversion stability, highlighting their synergistic benefits within the integrated process. This work underscores the potential of integrating Calcium Looping with Calcium Hydroxide for improved multicycle performance and opens pathways for scaling experiments to pilot systems, alongside assessing the efficiency and economic viability of this integrated approach., Financial support is acknowledged from grants TED2021-131839B-C22 and PDC2021-121552-C21 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Flash Joule Heating-Boro/Carbothermal Reduction (FJH-BCTR): An approach for the instantaneous synthesis of transition metal diborides

  • Taibi, Ahmed
  • Gil-González, Eva
  • Sánchez-Jiménez, Pedro E.
  • Perejón, Antonio
  • Pérez-Maqueda, Luis A.
Transition metal diborides (TMB2), such as ZrB2 and HfB2, are a class of ultra-high-temperature ceramics (UHTCs) that have attracted considerable attention due to their performance in extreme environments. Their implementation is burdened by the high energetic requirement of traditional synthetic procedures. Here, we report a novel methodology, termed as Flash Joule Heating-Boro/Carbothermal Reduction (FJH-BCTR), for the instantaneous synthesis of phase-pure sub-micron powders of several TMB2 and composite within seconds and without any external source of heating. The immediate synthesis is attributed to the Joule heat generated by the current, enabling extremely fast heating and cooling rates and, therefore, avoiding excessive grain growth. The advantages of FJH-BCTR are thoroughly displayed and can be summarized as; highly efficient, it allows a dramatic drop in terms of energy and time; universal, several TMB2 and composite can be prepared; and flexible, different experimental parameters can be tuned to achieve the desired phase., This work has been funded by EU Next Generation funds and Spanish Ministry of Science and Innovation (projects TED2021-131839B–C22 and PDC2021-121552-C21). Funding from Spanish Ministry of Science and Innovation (PID2022-140815OB-C22 and PID2022-141199OA-I00) is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Magnesium calcites for CO2 capture and thermochemical energy storage using the calcium-looping process

  • Perejón, Antonio
  • Arcenegui-Troya, Juan
  • Sánchez-Jiménez, Pedro E.
  • Diánez, María Jesús
  • Pérez-Maqueda, Luis A.
Chemicals and CAS Registry Numbers calcium 7440-70-2, 14092-94-5 calcium carbonate 13397-26-7, 13701-58-1, 14791-73-2, 471-34-1 carbon dioxide 124-38-9, 58561-67-4 magnesium 7439-95-4 magnesium oxide 1309-48-4, 1317-74-4 Calcium Calcium Carbonate Carbon Dioxide Magnesium Magnesium Oxide, In this study, a precipitation-based synthesis method has been employed to prepare magnesium calcites with the general formula Ca1-xMgxCO3, with the objective of use them in the calcium looping (CaL) process for CO2 capture (CaL-CCS) and thermochemical energy storage (CaL-CSP). The structure and microstructure of the samples have been characterized. It has been found by X-ray diffraction that the samples with a Ca:Mg molar ratio of 0.5:0.5 and 0.55:0.45 are phase pure, while the samples with molar ratios of 0.7:0.3 and 0.8:0.2 are composed by two phases with different stoichiometry. In addition, the sample prepared with calcium alone shows the aragonite phase. The microstructure of the magnesium-containing samples is composed of nanocrystals, which are aggregated in spherical particles whereas the aragonite sample presents a typical rod-like morphology. The multicycle tests carried out under CaL-CCS conditions show that an increase on the MgO content in the calcined samples results in a reduced value of effective conversion when compared to aragonite. On the other hand, under CaL-CSP conditions, the samples with the higher MgO content exhibit nearly stable effective conversion values around 0.5 after 20 cycles, which improve the results obtained for aragonite and those reported for natural dolomite tested under the same conditions., Financial support is acknowledged from grants TED2021-131839B–C22 and PDC2021-121552-C21 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Microstructural control by freeze-casting of CaO architectures for improved and stable thermochemical energy storage performance

  • Amghar, Nabil
  • Ivorra-Martínez, Juan
  • Perejón, Antonio
  • Hanaor, Dorian
  • Gurlo, Aleksander
  • Ramírez-Rico, Joaquín
  • Pérez-Maqueda, Luis A.
  • Sánchez-Jiménez, Pedro E.
This study investigates the development of porous calcium-based monoliths via freeze-casting (FC) as a novel approach for thermochemical energy storage, particularly within the Calcium Looping (CaL) process. The freeze-casting technique enabled the fabrication of scaffolds with controlled porosity using polyvinyl alcohol (PVA) as a binder. Experimental results demonstrated that freeze-cast monoliths exhibited superior multicycle performance under various carbonation and calcination conditions. The FC-CaCO<inf>3</inf> monolith achieved the highest residual conversion of 68.1 % under mild vacuum calcination conditions (780 °C, 0.1 bar CO<inf>2</inf>), significantly surpassing other configurations. Tests conducted in an inert atmosphere also yielded favorable results, with a conversion of 56.1 %, outperforming equivalent raw powder samples. The enhanced performance is attributed to improved CO<inf>2</inf> interaction with the porous structure, mitigating sintering effects and preserving active surface area. Morphological observations by X-ray tomography and SEM confirmed limited particle sintering after multiple cycles, maintaining a reactive surface that supported consistent conversion rates. The pore size distribution of the material evolves upon cycling resulting in an increased microporosity, while the pore network maintains a low tortuosity (τ ~ 1.5–2.0). The addition of dopants such as ZrO<inf>2</inf> and SiO<inf>2</inf> did not enhance performance, as the monoliths' inherent structure provided sufficient stability. These findings highlight freeze-casting as a promising method for creating advanced porous materials suitable for energy storage applications., Financial support is acknowledged from grants TED2021-131839B-C22 and PDC2021-121552-C21 (MCIN/AEI/10.13039/501100011033 and European Union Next Generation EU/PRTR) and by European Union NextGenerationEU/PRTR, and the grant PID2022-140815OB-C22 funded by MCIN/AEI/10.13039/501100011033 and ERDF A way of making Europe. PhD Fellowship granted to N. Amghar (PRE2018-085866) from the Spanish Government Agency Ministerio de Ciencia, Innovación y Universidades. J. Ivorra-Martinez thanks Generalitat Valenciana - GVA for funding a postdoc position through the CIAPOS program co-funded by ESF Investing in your future, grant number CIAPOS/2023/362. XCT measurements were performed at the X-ray laboratory of the Research, Technology and Innovation Center (CITIUS) of the University of Seville., Peer reviewed