Pasar al contenido principal

Resultados relacionados

Resultados totales (Incluyendo duplicados): 8
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

Towards cooling concrete: Evaluation of cement and cement composites under realistic climatic conditions

  • Torres-García, Alicia E.
  • Agbaoye, Ridwan O.
  • Carlosena, Laura
  • Goracci, Guido
  • Lezaun, Carlos
  • Dolado, Jorge S.
  • Beruete, Miguel
  • MIRACLE Project ID: 964450
Finding scalable, cost-effective and environmentally safe solutions for Passive Daytime Radiative Cooling (PDRC) is essential for addressing energy and climate challenges. This study demonstrates the feasibility of achieving PDRC using only cement-based compounds, without the need for additional whitening agents or other additives. Unlike previous approaches that rely on external additives, the proposed solution leverages two fundamental cement phases—portlandite and tobermorite—offering a scalable and low-impact alternative. The research evaluates the radiative cooling potential of these phases, along with two widely used cements—white cement (WC) and ordinary Portland cement (OPC), by analyzing and comparing their homogenized complex permittivities, derived using the Kramers-Kronig (KK) method. Simulations were conducted to assess the cooling power over one year across three different climates using actual meteorological data. The portlandite exhibits positive Pcool, maintaining a temperature equal to or below the ambient temperature more than 90 % of the time in dry desert and warm temperate locations. Indoor controlled measurements results reveal that portlandite (CH) may exhibit temperatures 15 °C lower than OPC and 5 °C lower than WC., The research presented in this paper has been supported by funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No. 64450 (MIRACLE project, more information available at www.miracle-concrete.eu) from the EU Commission. Additionally, this work has received financial support from the projects TED2021-132074B-C31, TED2021-132074B-C32 and TED2021-132074B-C33, funded by MCIN/AEI/10.13039/501100011033, and the European Union NextGenerationEU/PRTR and from the projects PID2022-137845NB-C21, PID2022-137845NB-C22 funded by MCIN/AEI/10.13039/501100011033/and by FEDER Una manera de hacer Europa., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publicación Artículo científico (JournalArticle)

A Modern Roman-Inspired Concrete with Daytime Radiative Cooling Capacity

  • Dolado, Jorge S.
  • Goracci, Guido
  • Moutaoukil, Ghizlane
  • Agbaoye, Ridwan O.
  • Beruete, Miguel
  • Torres-García, Alicia E.
  • Carlosena, Laura
  • Prabhu, Achutha
  • Ibáñez, Jose A.
  • Adams, Nick
  • Lipzig, Nicole van
  • Allacker, Karen
Addressing global warming through the modernization of buildings and urban areas is a major challenge. Passive daytime radiative cooling (PDRC) materials offer potential solutions, but none have effectively replaced concrete's dominant role in urban environments. Here, a Roman-inspired concrete with PDRC capabilities is presented, combining high solar reflectance (≈0.95) and long-wave infrared (LWIR) emittance (≈0.91). It delivers cooling powers over 45 W m- 2 under average solar intensities of 850 W m- 2 without a convection shield. On hot days (above 30°C), it stays 2°C cooler than the surrounding air under solar irradiance up to 985 W m- 2. Simulations predict this concrete can reduce energy use and CO2 emissions by ≈50% in hot regions and lower urban surface temperatures by up to 10°C during heat waves. This breakthrough offers a cheap, scalable and sustainable solution for energy efficiency and climate resilience., This work was supported by the MIRACLE project. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 964450. JSD, MB, and KA acknowledge the support of COOLCRETE project. COOLCRETE has received funding from the European Union'sHorizon 2020 research and innovation programme under grant agreement No 101164420. JSD and MB acknowledge the grants nos. PID2022-137845NBC21-C22 and TED2021-132074B C31-C33 funded by MICIU/AEI/ 10.13039/501100011033, by ERDF/EU, and the European Union NextGenerationEU/PRTR. The authors also thank the Quantum Beams & Sustainable Materials group of the Materials Physics Center for the help with the Confocal Raman measurements and discussions. Finally, JSD acknowledges IQE for providing zeolite sampl, Peer reviewed
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Contribución de congreso (ConferenceOutput)

Lithography-free perfect narrowband absorbers using simple layered structures

  • Lezaun Capdevila, Carlos
  • Navajas Hernández, David
  • Liberal Olleta, Íñigo
  • Beruete Díaz, Miguel
Light absorbers are key components for multiple applications ranging from heat and energy management to communications and sensing. This work explores different complex permittivity combinations for material-reflector and material-spacer-reflector configurations, achieving perfect absorption under different permittivity regimes and thicknesses. Using silicon carbide, we discuss polarization and angle dependencies, and the potential of exploiting different permittivity regimes within a device for multi-band absorption. This work helps standardize absorber design and offer insights to engineer perfect absorbers for applications such as thermal emission, absorption, communication and sensing., The project has received funding from the European Union's Horizon 2020 research and innovation program under grant agreement 964450, MIRACLE and from project TED2021-132074B-C33, funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR\.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Multiple absorption regimes in simple lithography-free structures leading to ultrathin slabs

  • Lezaun Capdevila, Carlos
  • Navajas Hernández, David
  • Liberal Olleta, Íñigo
  • Beruete Díaz, Miguel
Electromagnetic absorbers serve as fundamental components for a wide range of applications, encompassing energy and heat management, sensing, and communications. In this study, we explore several complex permittivity combinations for lithography-free material-reflector and material-spacer-reflector configurations that lead to perfect absorption peaks across distinct permittivity regimes and varying thicknesses. We provide an extensive analysis of angle and polarization dependencies, specifically using silicon carbide as an illustrative example. Our findings reveal the potential for harnessing different absorption regimes within a single device, thus enabling the realization of multiband absorption capabilities. Furthermore, we demonstrate perfect absorption linked with extreme values of permittivity, and we find the conditions to get perfect absorption in ultrathin slabs. In addition, we carry out an analysis about the response at oblique incidence, and we identify a particular mode in the negative permittivity region and its hybridization with epsilon-near-zero modes at oblique incidence. This investigation serves as a valuable standardization of absorber design, offering insights to develop perfect absorbers for infrared applications such as thermal emission, communications, and sensing., The research presented in this paper has been supported by funding from the European Union's Horizon 2020 research and innovation program under Grant Agreement No. 964450 (MIRACLE project, more information available in Ref. ) from the EU Commission. Additionally, this work has received financial support from Project No. TED2021-132074B-C33, funded by MCIN/AEI/10.13039/501100011033, and the European Union NextGenerationEU/PRTR and from Project No. PID2022-137845NB-C21, funded by MCIN/AEI/10.13039/501100011033 and by FEDER Una manera de hacer Europa. C.L. acknowledges financial support from Santander Bank and Public University of Navarra under resolution 2659/2021.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

A modern roman-inspired concrete with daytime radiative cooling capacity

  • Dolado, Jorge S.
  • Goracci, Guido
  • Moutaoukil, Ghizlane
  • Agbaoye, Ridwan O.
  • Beruete Díaz, Miguel
  • Torres García, Alicia E.
  • Carlosena Remírez, Laura
  • Prabhu, Achutha
  • Ibáñez, José A.
  • Adams, Nick
  • Lipzig, Nicole van
  • Allacker, Karen
Addressing global warming through the modernization of buildings and urban areas is a major challenge. Passive daytime radiative cooling (PDRC) materials offer potential solutions, but none have effectively replaced concrete's dominant role in urban environments. Here, a Roman-inspired concrete with PDRC capabilities is presented, combining high solar reflectance (≈0.95) and long-wave infrared (LWIR) emittance (≈0.91). It delivers cooling powers over 45 W m−2 under average solar intensities of 850 W m−2 without a convection shield. On hot days (above 30°C), it stays 2°C cooler than the surrounding air under solar irradiance up to 985 W m−2. Simulations predict this concrete can reduce energy use and CO2 emissions by ≈50% in hot regions and lower urban surface temperatures by up to 10°C during heat waves. This breakthrough offers a cheap, scalable and sustainable solution for energy efficiency and climate resilience., This work was supported by the MIRACLE project. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 964450. JSD, MB, and KA acknowledge the support of COOLCRETE project. COOLCRETE has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 101164420. JSD and MB acknowledge the grants nos. PID2022-137845NBC21-C22 [i.e. PID2022-137845NB-C21 and PID2022-137845NB-C22] and TED2021-132074B C31-C33 [i.e. TED2021-132074B-C31 and TED2021-132074B-C33] funded by MICIU/AEI/ 10.13039/501100011033, by ERDF/EU, and the European Union NextGenerationEU/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Artificial intelligence-enhanced metamaterial bragg multilayers for radiative cooling

  • Osuna Ruiz, David
  • Aznárez-Sanado, Maite
  • Herrera, Pilar
  • Beruete Díaz, Miguel
A full numerical study combining artificial intelligence (AI) methods and electromagnetic simulation software on a multilayered structure for radiative cooling (RC) is investigated. The original structure is made of SiO2/Si nanometer-thick layers that make a Bragg mirror for wavelengths in the solar irradiance window (0.3–4 μm). The structures are then optimized in terms of the calculated net cooling power and characterized via the reflected and absorbed incident light as a function of their structural parameters. This investigation provides with optimal designs of beyond-Bragg, all-dielectric, ultra-broadband mirrors that provide net cooling powers in the order of ≈100 W m−2, similar to the best-performing structures in literature. Furthermore, it explains AI's success in producing these structures and enables the analysis of resonant conditions in metal-free multilayers with unconventional layer thickness distributions, offering innovative tools for designing highly efficient structures in RC., This work was supported by project PC048-049-DisenIA from Gobierno de Navarra (GN) and by grant TED2021-132074B-C33 funded by MCIN/AEI/10.13039/501100011033 and by European Union NextGenerationEU/PRTR.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Towards cooling concrete: evaluation of cement and cement composites under realistic climatic conditions

  • Torres García, Alicia E.
  • Agbaoye, Ridwan O.
  • Carlosena Remírez, Laura
  • Goracci, Guido
  • Lezaun Capdevila, Carlos
  • Dolado, Jorge S.
  • Beruete Díaz, Miguel
Finding scalable, cost-effective and environmentally safe solutions for Passive Daytime Radiative Cooling (PDRC) is essential for addressing energy and climate challenges. This study demonstrates the feasibility of achieving PDRC using only cement-based compounds, without the need for additional whitening agents or other additives. Unlike previous approaches that rely on external additives, the proposed solution leverages two fundamental cement phases—portlandite and tobermorite—offering a scalable and low-impact alternative. The research evaluates the radiative cooling potential of these phases, along with two widely used cements—white cement (WC) and ordinary Portland cement (OPC), by analyzing and comparing their homogenized complex permittivities, derived using the Kramers-Kronig (KK) method. Simulations were conducted to assess the cooling power over one year across three different climates using actual meteorological data. The portlandite exhibits positive Pcool, maintaining a temperature equal to or below the ambient temperature more than 90 % of the time in dry desert and warm temperate locations. Indoor controlled measurements results reveal that portlandite (CH) may exhibit temperatures 15 °C lower than OPC and 5 °C lower than WC., The research presented in this paper has been supported by funding from the European Union's Horizon 2020 research and innovation program under grant agreement No. 64450 (MIRACLE project, more information available at www.miracle-concrete.eu) from the EU Commission. Additionally, this work has received financial support from the projects TED2021-132074B-C31, TED2021-132074B-C32 and TED2021-132074B-C33, funded by MCIN/AEI/10.13039/ 501100011033, and the European Union NextGenerationEU/PRTR and from the projects PID2022-137845NB-C21, PID2022-137845NB-C22 funded by MCIN/AEI/10.13039/501100011033/and by FEDER Una manera de hacer Europa.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publicación Artículo científico (JournalArticle)

Metal-free design of a multilayered metamaterial with chirped Bragg grating for enhanced radiative cooling

  • Osuna Ruiz, David
  • Lezaun Capdevila, Carlos
  • Torres García, Alicia E.
  • Beruete Díaz, Miguel
A wideband, all-dielectric metamaterial structure for enhancing radiative cooling is investigated. The structure is optimized to reflect most of the solar irradiance window (between 0.3 µm–3 µm), which is one of the biggest challenges in highly efficient radiative cooling coatings. The design is based on the principles of Bragg gratings, which constitutes a simple synthesis procedure to make a broadband reflector of reduced dimensions, without metallic layers, while keeping a flat enough response in the entire bandwidth. Numerical results show that reflection of solar irradiation can be easily tailored and maximized using this method, as well as the net cooling power of the device, about ∼79 W/m2 at daytime (about double at night-time) and a temperature reduction of 23 K (assuming no heat exchange) and 7 K assuming a heat exchange coefficient of 10 W/m2/K, for a device and ambient temperatures of 300 K and 303 K, respectively. This occurs even in detriment of absorption in the atmospheric window (8 µm–13 µm). Results also show the importance of efficiently reflecting solar irradiance for such technologies and its relevance in synthesis and design without using metallic components., European Commission (Next Generation, PRTR, TED2021-132074B-C33); Ministerio de Ciencia e Innovación (TED2021-132074B-C33); Gobierno de Navarra (PC048-049-DisenIA).