Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 12
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental study of the droplet characteristics of a SCR injector spray through optical techniques

  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Postrioti, L.
  • Moreno-Gasparotto, Armando Enrique
  • Brizi, G.
[EN] The requirement of high-fidelity experimental data of microscopic properties of sprays motivates the continuous development of optical tools, since they are determinant in the understanding of atomization and evaporation process in a variety of multiphase flows.This work compares two optical techniques and an interferometry method for the measurement of the droplet size and velocity of a spray produced by a commercial Selective Catalytic Reduction (SCR) dosing unit also known as Urea Water Solution (UWS) injector. The adequate dosing and mixing of the injected fluid is fundamental for the proper functioning of the (SCR) system, therefore studying the spray characteristics with proper techniques is important to comprehend the phenomena occurring during the injection process. The SCR system is employed in the elimination of nitrous oxides present in exhaust gases of an engine. The objective is to compare the techniques in order to obtain accurate and reliable data that can be used to validate Computational Fluid Dynamics (CFD) models and improve current exhaust geometries and mixers. The studied techniques are Phase Doppler Anemometry (PDA), High Resolution Laser Backlight Imaging (HRLBI) and High Speed Microscopic Imaging (HSMI). The PDA determines the properties of the spray, obtaining the diameter and velocity of droplets in the axis parallel to the axis of the injector. With the HRLBI frames of 2040 x 2040 pixels were captured at different instants of the injection event, achieving a spatial resolution of 7 um/pixel, allowing the visualization of the smallest droplets present in the spray. With the HSMI videos of the spray using a fast camera and a microscopic lens were recorded at 150.000 fps to measure the diameter and the velocity of the droplets in 2 directions. The measurements were carried out using water as the injected fluid at 3 different injection pressures and the results are compared to determine the limits and advantages of each technique. The droplet diameter obtained by the PDA tests is similar to the observed results in the HRLBI, whereas the HSMI missed the smaller droplets. On the other hand the droplet velocity is in good concordance in the axis parallel to the axis of the injector, proving the HSMI a suitable technique to quantify the velocity of the droplets., The equipment used for the experiments was financially supported by MEMORIA IDIFEDER/2018/037 "Diagnostico optico a alta velocidad para el estudio de procesos termo-fluidodinamicos en sistemas de inyeccion" from Generalitat Valenciana. The Dipartimento di Ingegneria -University of Perugia is also acknowledged for the support to experimental activities with Ricerca di Base -2019 Program. The author A. Moreno thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2018-S2-13), which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID). The Authors would like to thank Jose Enrique del Rey and Omar Huerta for their support in the experimental measurements.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Corrosion resistance of ultra-high performance fibre- reinforced concrete

  • Valcuende Payá, Manuel Octavio|||0000-0002-9967-1554
  • Lliso-Ferrando, Josep Ramon|||0000-0002-2457-9024
  • Ramón Zamora, José Enrique
  • Soto Camino, Juan
[EN] The corrosion resistance of ultra-high performance concrete (UH) made with different fibre contents and under distinct curing conditions was studied. No signs of carbonation were observed after 1 year of accelerated carbonation testing (3% CO2). The fibreless UHs¿ electrical resistivity was above 5000 ¿·m, although these values were 2-fold higher than a UH with 1% fibres and approximately 5-fold higher than a UH with 2% fibres. Concrete resistance to chloride penetration was also extremely high (the diffusion coefficient equalled 1.3·10¿13 m2/s) and curing temperatures of 60 °C or 90 °C improved even more these properties, while lack of curing made them slightly worse. Given these excellent properties, the corrosion rate in specimens submerged in chloride solution for 1 year was negligible (iCORR from 0.007 to 0.025 µA/cm2). These values remained stable with time, unlike the 50 MPa concrete at 2 months when iCORR starting to increase and was 12-fold higher after 1 year. The time estimated for corrosion onset in UH is on average about 150-fold higher than that of 50 MPa., Authors thank to the Spanish Government the financial support of project BIA2016-78460-C3-3-R and to the European Union¿s Horizon 2020 the financial support of ReSHEALience project (Grant Agreement No. 760824). Furthermore, authors would like to express their gratitude for the support of the Universitat Politecnica de Valencia. Funding for open access charge: CRUE-Universitat Politecnica de Valencia. The predoctoral scholarship granted to Josep Ramon Lliso Ferrando within the program "Formacion de Personal Investigador" from the Universitat Politecnica de Valencia (FPI-UPV-2018) is also gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Significance of macrocell currents in reinforced concrete columns partially immersed in seawater

  • Lliso-Ferrando, Josep Ramon|||0000-0002-2457-9024
  • Gasch, Isabel|||0000-0001-7036-4481
  • Valcuende Payá, Manuel Octavio|||0000-0002-9967-1554
  • Soto Camino, Juan
[EN] Corrosion in reinforced concrete structures located in marine environments is probably the main cause of damage, especially in elements that are partially immersed in seawater. The moisture gradient and different chloride concentrations occur in pieces under such conditions, which give way to the formation of macrocell currents between different rebar regions. Despite being studied by several authors who have run experiments in solution or with small test specimens, the significance of macrocell currents in structures has not yet been accurately quantified. The present work studied four columns that were partially immersed in seawater for more than 1 year, when the electrical resistance of concrete and the corrosion rate were monitored. After exposure, moisture and chloride content analyses were performed, and a rebar inspection was carried out. The obtained results show that macrocell currents can increase mass loss by rebar corrosion between 3- and 8-fold. They also reveal that macrocell currents can mitigate corrosion damage in areas showing cathodic performance., The authors thank the Spanish Government for Grant PID2020-119744RB-C21 funded by MCIN/AEI/10.13039/501100011033, and the support of the Universitat Politecnica de Valencia. They are also grateful for the predoctoral scholarship granted to Josep Ramon Lliso Ferrando as part of the "Formacion de Personal Investigador" programme of the Universitat Politecnica de Valencia (FPI-UPV-2018).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sensitivity of pollutants abatement in oxidation catalysts to the use of alternative fuels

  • Piqueras, P.|||0000-0002-3767-0839
  • Ruiz-Lucas, María José
  • Martin Herreros, Jose
  • Tsolakis, Athanasios
[EN] The aim to reduce well to wheel emissions incentives the utilisation of alternative fuels (low to zero carbon content and/or low well to tank emissions) as well as the enhancement of engine efficiency. In parallel, the reduction of engine tailpipe emissions brings new challenges such as the decrease of the exhaust gas temperature. This trend penalises the ability of the exhaust aftertreatment system to eliminate pollutant emissions. In addition, the combustion of alternative fuels and new combustion modes induce changes in the nature and concentration of the exhaust species, which is known to affect the pollutants abatement mechanisms. This investigation provides new understanding on the sensitivity of pollutants abatement in oxidation catalysts to the use of alternative fuels. The studied fuels are conventional diesel, alternative fuels (rapeseed methyl ester and gas to liquid) as well as propane using a dual-fuel combustion strategy. The research combines experimental conversion efficiency from genuine exhaust gases with modelling work useful to explain the reasons for the change in light-off temperature as a function of the fuel. In addition to the CO and NO impact, HC surrogates are proposed distinguishing species of different reactivity for each fuel based on the experimental HC speciation. The results highlight the role of the engine-out emissions on the pollutants conversion efficiency. Their fashion with different fuels contributes to evidence the interest for low engine-out emissions along with low light alkanes content in total HC, as promoted by alternative fuels, to reduce the oxidation light-off temperature., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R and by Universitat Politecnica de Valencia under a grant with reference number FPI-2018-S2-10 to the Ph.D. student Maria Jose Ruiz
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of macrocell currents on rebar corrosion in reinforced concrete structures exposed to a marine environment

  • Lliso-Ferrando, Josep Ramon|||0000-0002-2457-9024
  • Gasch, Isabel|||0000-0001-7036-4481
  • Martínez-Ibernón, Ana|||0000-0003-2136-5650
  • Valcuende Payá, Manuel Octavio|||0000-0002-9967-1554
[EN] Autonomous corrosion monitoring systems in reinforced concrete structures tend to use sensors that are electrically isolated from rebars. This monitoring strategy ignores the macrocell currents that take place between active and passive areas of reinforcement. The effect of these currents has been studied on rebar corrosion in structures exposed to a marine environment. The results showed the existence of macrocell currents generates greater anodic polarisation in rebars¿ active areas, which favours chloride migration towards steel surface. As a result, corrosion onset takes place sooner, the concentration of the chlorides is higher, and the corrosion rate increases. When a rebar is in passive state, steel mass loss is negligible due to macrocell currents. However, after corrosion onset, the influence of these currents is greater the worse concrete quality is, and the smaller cover is. The corrosion rate showed differences of almost two orders of magnitude in concrete C30 and of one order of magnitude in concrete C50. When the total corrosion rate is determined only by measuring microcell currents, the obtained values tend to underestimate the mass loss due to corrosion by 90%. Conversely, when the analysis includes macrocell currents, a good fit between the theoretical and real values is obtained., The authors thank the Spanish Government for Grant PID2020-119744RB-C21 funded by MCIN/AEI/10.13039/501100011033, and the support of the Universitat Politecnica de Valencia. They are also grateful for the predoctoral scholarship granted to Josep Ramon Lliso Ferrando as part of the "Formacion de Personal Investigador" programme from the Universitat Politecnica de Valencia (FPI-UPV-2018) , and Grant FPU 16/00723 funded by MCIN/AEI/10.13039/501100011033 and by "ESF Investing in your future".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Using momentum flux measurements to determine the injection rate of a commercial Urea Water Solution injector

  • Payri, Raul|||0000-0001-7428-5510
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Marti-Aldaravi, Pedro|||0000-0003-4650-4004
  • Moreno-Gasparotto, Armando Enrique
[EN] The Selective Catalytic Reduction (SCR) technology allows the transformation of the Nitrous Oxide emissions present in exhaust gases into gaseous nitrogen and water. For a proper operation of the SCR, a urea-water solution (UWS) injector must dose an adequate amount of liquid into the exhaust pipe in order to avoid deposit formation and to guarantee the SCR system efficiency. This task requires the knowledge of the performance of the injector. Then, the goal of this work is to study the hydraulic performance of a UWS injector, by means of measuring the spray momentum flux in order to understand the influence of different variables as injected fluid, injection pressure, counter pressure and cooling temperature of the injector on the flow characteristics. The tested injector was cooled at three different temperatures, 60, 90 and 120 degrees C, the injection pressure of the UWS was set at 5, 7 and 9 bar, with counter pressures of 750, 900, 1000 and 2000 mbar for the two tested fluids, water and UWS. The measurements were carried out using an experimental facility developed at CMT-Motores Termicos for the determination of spray momentum flux, where a piezoelectric pressure sensor was located near the nozzle exit of the injector, which measures the impact force of the spray. Additionally, the proposed methodology allowed to determine the injected mass flow and to capture the transient injection events, such as the opening and closing stages. Moreover, mass flow rate measurements of the injector were performed under the same operating conditions, determining the influence of the injection pressure, cooling temperature, counter pressure and fluid properties. Regarding the pressure, the tendency was as expected, the higher the injection pressure the higher the Momentum flux and flow rate. Results showed that an increment of the cooling temperature of the injector induces the appearance of flash boiling conditions, having an impact on the total injected mass and momentum flux, changing the behaviour of the spray. For the same conditions, water has a higher momentum flux than the UWS due to differences in fluid properties and velocity at the nozzle exit., This work has been partially funded by Spanish Ministerio de Ciencia, Innovacion y Universidades through project RTI2018099706B100. The author A. Moreno thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI2018S213) , which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo (PAID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of the cell geometry on the conversion efficiency of oxidation catalysts under real driving conditions

  • Piqueras, P.|||0000-0002-3767-0839
  • Ruiz, María José
  • Martín Herreros, José
  • Tsolakis, Athanasios
[EN] Worldwide pollutant regulations applied to the transportation sector are progressively tightening the emission limits and widening the operating conditions of the type approval tests. As a result, the layout and thermal management of the exhaust system is becoming highly complex looking to achieve early catalytic converter activation. On this regard, the monolith meso-geometry plays a primary role to optimise the pollutants con -version efficiency. The geometrical characteristics simultaneously affect and trade-off multiple flow phenomena as the exhaust gas is transported through the channels. These include the bulk gas and internal pore diffusion towards the active sites in addition to the heat transfer including convection, radial conductivity and thermal capacitance. In this work, the impacts of the cell size, cross-section shape, washcoat loading and substrate material on CO and HC conversion efficiency have been investigated under representative real driving condi-tions. From the real driving conditions experimental data, the study decouples the influence of the washcoat loading from the cell size and material applying a catalytic converter model. Detailed expressions are provided for the calculation of the specific surfaces and heat and mass transfer parameters as a function of the cell and washcoat meso-geometry in square and triangular cells. Therefore, this work enables to identify the processes which govern the catalytic abatement of pollutant emissions. In particular, the role of the gas and washcoat specific surfaces is highlighted because of its importance on the optimization of the mass transfer process by means of a proper cell geometry selection. In parallel, the differences in the change of the CO and HC abatement patterns, which are explained by the characteristic CO emission spikes in accelerations and the HC accumulation, contribute to evidence the limitations on the conversion efficiency benefit that the optimum cell geometry and washcoat loading can provide., The authors acknowledge FEDER and Spanish Ministerio de Economia y Competitividad for partially supporting this research through project TRA2016-79185-R. Additionally, the Ph.D. student Maria Jose Ruiz has been funded by a grant from Universitat Politecnica de Valencia with reference number FPI-2018-S2-10.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of Pre-Turbine Small-Sized Oxidation Catalyst on Engine Performance and Emissions under Driving Conditions

  • Serrano, J.R.|||0000-0003-0692-3917
  • Piqueras, P.|||0000-0002-3767-0839
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Ruiz-Lucas, María José
[EN] The earlier activation of the catalytic converters in internal combustion engines is becoming highly challenging due to the reduction in exhaust gas temperature caused by the application of CO2 reduction technologies. In this context, the use of pre-turbine catalysts arises as a potential way to increase the conversion efficiency of the exhaust aftertreatment system. In this work, a small-sized oxidation catalyst consisting of a honeycomb thin-wall metallic substrate was placed upstream of the turbine to benefit from the higher temperature and pressure prior to the turbine expansion. The change in engine performance and emissions in comparison to the baseline configuration are analyzed under driving conditions. As an individual element, the pre-turbine catalyst contributed positively with a relevant increase in the overall CO and HC conversion efficiency. However, its placement produced secondary effects on the engine and baseline aftertreatment response. Although small-sized monoliths are advantageous to minimize the thermal inertia impact on the turbocharger lag, the catalyst cross-section is in trade-off with the additional pressure drop that the monolith causes. As a result, the higher exhaust manifold pressure in pre-turbine pre-catalyst configuration caused a fuel consumption increase higher than 3% while the engine-out CO and HC emissions did around 50%. These increments were not completely offset despite the high pre-turbine pre-catalyst conversion efficiency (>40%) because the partial abatement of the emissions in this device conditioned the performance of the close-coupled oxidation catalyst., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R and by Universitat Politecnica de Valencia under a grant with reference number FPI-2018-S2-10 to the Ph.D. student Maria Jose Ruiz.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental approach for the analysis of the flow behaviour in the stator of a real centripetal turbine

  • Galindo, José|||0000-0001-6068-182X
  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • García-Cuevas González, Luis Miguel|||0000-0001-9340-0617
  • Hervás-Gómez, Natalia
[EN] During normal operation, radial turbines may work in off-design conditions. Off-design conditions may be characterised by very low expansion ratios, very high expansion ratios, very low rotational speeds or very high rotational speeds. All of these cases are difficult to characterise experimentally due to high experimental uncertainties or a lack of capabilities in the system feeding pressurised air to the turbine. Also, there are two- and three-dimensional computational fluid dynamics simulations at these operating points but could not be accurate enough due to high turbulence effects, flow detachment and shock wave generation. With a lack of high-quality data, experimental or computational, to fit the reduced-order turbine models used in zero- and one-dimensional engine simulations, there are large uncertainties associated to their results in off-design conditions. This work develops an experimental facility able to characterise the internal flow of radial turbine stators in terms of pressure and velocity fields at off-design and regular working conditions. The facility consists of an upscaled model of a radial turbine volute and stator fed with air in pressure- and temperature-controlled conditions, so different sensors can be used inside it with the least amount of flow disturbance. The different restrictions considered in the design of the upscaled model are presented, and their effects in the final experimental apparatus capabilities are discussed. A preliminary comparison between computational fluid dynamics simulations and experimental data shows encouraging results., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partly sponsored by the programme 'Ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia (UPV), Spain'. The support given to Ms N.H.G. by Universitat Politecnica de Valencia through the 'FPI-Subprograma 2' (No. FPI-2018-S2-1368) grant within the 'Programa de Apoyo para la Investigacion y Desarrollo (PAID-0118)' is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Investigation of the urea-water solution atomization process in engine exhaust-like conditions

  • Payri, Raul|||0000-0001-7428-5510
  • Bracho Leon, Gabriela|||0000-0002-9198-7044
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Moreno-Gasparotto, Armando Enrique
[EN] The injection process of the urea-water solution (UWS) determines the initial conditions for the mixing and evaporation of the fluid in the selective catalytic reduction system. In this study, the liquid atomization process of a UWS dosing system is investigated using optical diagnosis through back-light imaging. The droplet diameter distribution and the droplet velocity (in the axial and tangential components) of the liquid spray are quantified under different air flow and injection conditions. A new test facility was designed to study UWS spray under conditions that resemble those of the engine exhaust pipe, which is capable of reaching an air flow of 400 kg/h and air temperatures up to 400 degrees C. The test matrix consisted of variations in the air flow temperature, air mass flow and UWS injection pressure. A high speed camera was used for capturing the images of the liquid spray, comparing the atomized liquid behaviour in three different regions of the plume: the first one near the nozzle exit, and the other two in the developed region of the spray (one aligned with the injector axis and the other at the spray periphery). Increasing the injection pressure affected the atomization process producing smaller particles with higher velocities in the axial and tangential components, promoting wider global spray angles, that combined with high air flow temperatures could improve the evaporation and mixing process in the SCR system. The main contribution is the development of an alternative technique for the quantification of the droplet size and velocity., The equipment used for the experiments was financially supported by IDIFEDER2018 from Generalitat Valenciana. The author A. Moreno thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2018-S2-13), which is included within the framework of Programa de Apoyo para la Investigacien y Desarrollo (PAID).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Design and Numerical Analysis of Flow Characteristics in a Scaled Volute and Vaned Nozzle of Radial Turbocharger Turbines

  • Tiseira, Andrés-Omar|||0000-0001-9472-2386
  • Navarro, Roberto|||0000-0003-2587-4954
  • Inhestern, Lukas Benjamin
  • Hervás-Gómez, Natalia
[EN] Over the past few decades, the aerodynamic improvements of turbocharger turbines contributed significantly to the overall efficiency augmentation and the advancements in downsizing of internal combustion engines. Due to the compact size of automotive turbochargers, the experimental measurement of the complex internal aerodynamics has been insufficiently studied. Hence, turbine designs mostly rely on the results of numerical simulations and the validation of zero-dimensional parameters as efficiency and reduced mass flow. To push the aerodynamic development even further, a precise validation of three-dimensional flow patterns predicted by applied computational fluid dynamics (CFD) methods is in need. This paper presents the design of an up-scaled volute-stator model, which allows optical experimental measurement techniques. In a preliminary step, numerical results indicate that the enlarged geometry will be representative of the flow patterns and characteristic non-dimensional numbers at defined flow sections of the real size turbine. Limitations due to rotor-stator interactions are highlighted. Measurement sections of interest for available measurement techniques are predefined., The authors disclose receipt of the following financial support for the research, authorship, and/or publication of this article: This work was partly sponsored by the program "Ayuda a Primeros Proyectos de Investigacion (PAID-06-18), Vicerrectorado de Investigacion, Innovacion y Transferencia de la Universitat Politecnica de Valencia (UPV), Spain". The support given to Ms. N.H.G. by Universitat Politecnica de Valencia through the "FPI-Subprograma 2" (No.FPI-2018-S2-1368) grant within the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-18)" is gratefully acknowledged
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Performance of a diesel oxidation catalyst under diesel-gasoline reactivity controlled compression ignition combustion conditions

  • Piqueras, P.|||0000-0002-3767-0839
  • García Martínez, Antonio|||0000-0001-5783-4936
  • Monsalve-Serrano, Javier|||0000-0001-8593-095X
  • Ruiz, María José
[EN] Reactivity controlled compression ignition is a promising combustion strategy due to the combination of excellent thermal efficiency with ultra-low nitrogen oxides and particulate matter raw emissions. However, very high levels of unburned hydrocarbons and carbon monoxide emissions are found. It limits the reactivity controlled compression ignition use at very low loads and presents an additional challenge for the diesel oxidation catalyst. The low exhaust temperature and high carbon monoxide and hydrocarbon concentration can penalise the catalyst conversion efficiency. The objective of this work is to evaluate the response of an automotive diesel oxidation catalyst when used for reactivity controlled compression ignition combustion combining experimental and modelling approaches. For this purpose, dedicated tests have been done using diesel-gasoline as fuel combination in a single-cylinder engine. This way, the catalyst conversion efficiency has been determined within a wide operating range covering hydrocarbon adsorption conditions and the pollutants abatement dependence on the mass flow and temperature. The experimental results in the full-size catalyst has been analysed by modelling. A lumped diesel oxidation catalyst model has been applied to extend the results to multi-cylinder engine conditions and to determine the light-off curves for both carbon monoxide and hydrocarbons. These tests evidence the penalty in light-off temperature due to high pollutants mass fraction, which promotes inhibition limitations to the reaction rate., This research has been partially supported by FEDER and the Government of Spain through project TRA2016-79185-R. Additionally, the Ph.D. student Maria Jose Ruiz has been funded by a grant from Universitat Politecnica de Valencia with reference number FPI-2018S2-10.