Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 29
Encontrada(s) 1 página(s)

Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Evaluación del volumen de influencia de 4 sondas capacitivas de tipo tubular

  • Bellosta Diest, Amelia
  • Echeverría, Miguel
  • Campo-Bescós, Miguel
El control eficiente del agua es clave en la agricultura de precisión, ya que tanto déficit como exceso afectan el desarrollo radicular de los cultivos. Los sensores capacitivos tubulares permiten monitorizar de forma continua el contenido de agua en el su elo. Este estudio evaluó cuatro sondas comerciales mediante un procedimiento empírico y replicable, con el objetivo de caracterizar el volumen efectivamente explorado por cada una bajo condiciones comparables. Las mediciones se realizaron en agua y aire, variando la distancia entre sensor y medio mediante capas de papel para analizar la sensibilidad a distintas separaciones. Los resultados muestran que el volumen explorado varía significativamente entre fabricantes y según el percentil de señal acumulada. Dado que las sondas se probaron en medios distintos al suelo, los resultados son válidos principalmente de forma relativa o comparativa, y deben interpretarse con precaución al extrapolarlos a condiciones reales de cultivo., Efficient water management is crucial in precision agriculture, as both deficit and excess can affect crop root development. Tubular capacitive sensors allow continuous monitoring of soil water content. This study evaluated four commercial sensors using an empirical and replicable procedure to characterize the effectively explored volume of each under comparable conditions. Measurements were conducted in water and air, progressively varying the distance between sensor and medium using layers of paper to analyze sensitivity at different separations. Results show that the explored volume varies significantly between manufacturers and according to the cumulative signal percentile. Since the sensors were tested in media different from soil, the results are primarily valid in relative or comparative terms and should be interpreted with caution when extrapolating to real soil conditions., El Gobierno de Navarra ha financiado la contratación de Amelia Bellosta en el marco de la convocatoria de ayudas 'Doctorados Industriales 2024' (Nº Expediente: 0011-1408-2024-000029). Hydrotecna desea agradecer a la Comunidad General de Regantes del Canal de Navarra por dar soporte en el marco del proyecto PERTE DIGITALIZACIÓN CICLO DEL AGUA (Nº Expediente: PDAR00039). MAC desea agradecer al proyecto Path4Med, bajo el programa HORIZON (Project ID: 101156867), en el marco del proyecto Path4Med HORIZON-MISS-2023-OCEAN-SOIL-01-01, financiado por la Unión Europea.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Diseño y captura de una base de datos para el reconocimiento de emociones minimizando sesgos

  • Jurío Munárriz, Aránzazu
  • Pascual Casas, Rubén
  • Domínguez Catena, Iris
  • Paternain Dallo, Daniel
  • Galar Idoate, Mikel
El reconocimiento de emociones a partir de expresiones faciales (FER) es un campo de investigación importante para la interacción persona-máquina. Sin embargo, los conjuntos de datos utilizados para entrenar modelos FER a menudo contienen sesgos demográficos que pueden conducir a la discriminación en el modelo final. En este trabajo, presentamos el diseño y la captura realizados para la creación de una nueva base de datos para FER, donde tratamos de minimizar los sesgos desde el propio diseño. La base de datos se ha creado utilizando diferentes métodos de captura. Para comprobar la reducción de los sesgos alcanzada, analizamos diferentes métricas de sesgo representacional y estereotípico sobre la base de datos generada y la comparamos frente a otras bases de datos estándar en la literatura de FER., Este trabajo ha sido financiado por el MICIU del Gobierno de España a través del proyecto PID2022-136627NBI00/ AEI/10.13039/501100011033 FEDER, UE y de una ayuda FPU (Rubén Pascual), por el Gobierno de Navarra (0011-1411-2020-000079 - Emotional Films), y por el Servicio de Investigación de la Universidad Pública de Navarra (contrato predoctoral de Iris Domínguez-Catena.)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Onset of irreversible reactions in overcharging lithium-ion cells: an experimental and modeling approach

  • Irujo Izcue, Elisa
  • Berrueta Irigoyen, Alberto
  • Lalinde Sainz, Iñaki
  • Arza, Joseba
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
Lithium-ion batteries are energy storage systems used in an increasing number of applications. Due to their flammable materials, their use entails risks of fire and explosion. The study of the abuse operation of these batteries before reaching the thermal runaway is a relevant research topic to prevent safety issues. There are various studies in the bibliography providing exhaustive thermal studies of the safe operating area, as well as concerning the thermal runaway. However, the onset irreversible reactions, that take place at a SOC around 110%, have not been properly analyzed. We present in this contribution an experimental study of this onset reaction measured in pouch Li-ion cells under various conditions of charge current and temperature. We also propose a lumped-parameter thermal model for the cell, which allows a detailed characterization of this exothermic reaction. The results achieved in this contributions can be a key tool to prevent overcharge accidents that may arise due to malfunctioning of the battery charger or battery management system., This work is part of the projects PID2019-111262RB-I00, funded by MCIN/AEI/10.13039/501100011033/, TED2021-132457B-I00, funded by MCIN/AEI/10.13039/501100011033/ and by the European Union NextGenerationEU/PRTR, STARDUST (774094), funded by European Union's Horizon 2020 research and innovation programme, HYBPLANT (0011-1411-2022- 000039), funded by Government of Navarre, and has also been supported by MCIN/AEI/10.13039/501100011033/ and by European Social Fund under a PhD scholarship (grant PRE2020-095314).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Medida de torsión en seguidores solares con sensores de fibra óptica, Torsion measurements on solar trackers using fiber optic sensors

  • Leandro González, Daniel
  • Bravo Acha, Mikel
  • López-Amo Sáinz, Manuel
  • Loayssa Lara, Alayn
  • Júdez Colorado, Aitor
  • Mariñelarena Ollacarizqueta, Jon
  • Falcone Lanas, Francisco
  • Jiménez Romero, Sergio
  • Moriana García, Iñaki
En este trabajo se ha monitorizado la torsión sufrida por una estructura de seguidores solares empleando sensores de fibra óptica. Estas medidas de campo se han obtenido con una red de sensores formada por 45 redes de difracción de Bragg en una huerta solar activa. Estos resultados, correlados con la velocidad y dirección del viento permitirían aumentar la eficiencia de los seguidores y ayudar a entender y prevenir efectos negativos relacionados con inestabilidades aeroelásticas., In this work, the torsion experienced by set of solar trackers is monitored using fiber optic sensors. The in-field measurements were obtained using a sensor network comprising 45 fiber Bragg gratings in an active solar plant. These results, correlated with wind speed and direction could increase efficiency and lead to understand and prevent harmful effects related to aeroelastic instability events., Este trabajo ha sido financiado por el proyecto WINDSOLAR (0011-1365-2017-000122) del Gobierno de Navarra, los proyectos TEC2016-76021-C2 y PID2019-107270RB-C22, los fondos FEDER, la European Union's Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No 838143 y las fundaciones 'Caja Navarra' y 'la Caixa' con el proyecto LCF/PR/PR13/51080004.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Temperature indicators and overtemperature detection in lithium-ion batteries based on electrochemical impedance spectroscopy

  • Lalinde Sainz, Iñaki
  • Berrueta Irigoyen, Alberto
  • Soto Cabria, Adrián
  • Arza, Joseba
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
Lithium-ion batteries are the leading technology for energy storage systems due to their attractive advantages. However, the safety of lithium-ion batteries is a major concern, as their operating conditions are limited in terms of temperature, voltage and state of charge. Therefore, it is important to monitor the conditions of lithium-ion batteries to guarantee safe operation. To this end, in the present work, we analyze electrochemical impedance spectroscopy (EIS) as a tool to estimate the temperature of batteries. Overtemperature abuse tests from 25 °C to 140 °C are performed at various states of charge, and EIS measurements are obtained during the tests. The influence of temperature on cell impedance at different frequencies is analyzed and new findings are revealed. The real part of the impedance is identified to be the best indicator for cell temperature estimation by EIS. In addition, the best frequency to achieve accurate temperature monitoring, avoiding disturbances produced by state of charge variations, is proposed based on experimental results. Finally, EIS is proven to be a reliable technique for overtemperature and thermal runaway detection., This work is part of the projects PID2019-111262RB-I00, funded by MCIN/AEI/10.13039/501100011033/, TED2021-132457B-I00, funded by MCIN/AEI/10.13039/501100011033/ and by the European Union NextGenerationEU/PRTR, STARDUST (774094), funded by European Union’s Horizon 2020 research and innovation programme, HYBPLANT (0011-1411-2022- 000039), funded by Government of Navarre, and has also been supported by MCIN/AEI/10.13039/501100011033/ and by European Social Fund under a PhD scholarship (grant PRE2020-095314).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Pushing the limits of Sentinel-2 for building footprint extraction

  • Ayala Lauroba, Christian
  • Aranda, Carlos
  • Galar Idoate, Mikel
Building footprint maps are of high importance nowadays since a wide range of services relies on them to work. However, activities to keep these maps up-to-date are costly and time-consuming due to the great deal of human intervention required. Several automation attempts have been carried out in the last decade aiming at fully automatizing them. However, taking into account the complexity of the task and the current limitations of semantic segmentation deep learning models, the vast majority of approaches rely on aerial imagery (<1 m). As a result, prohibitive costs and high revisit times prevent the remote sensing community from maintaining up-to-date building maps. This work proposes a novel deep learning architecture to accurately extract building footprints from high resolution satellite imagery (10 m). Accordingly, super-resolution and semantic segmentation techniques have been fused to make it possible not only to improve the building's boundary definition but also to detect buildings with sub-pixel width. As a result, fine-grained building maps at 2.5 m are generated using Sentinel-2 imagery, closing the gap between satellite and aerial semantic segmentation., Christian Ayala was partially supported by the Goverment of Navarra under the industrial PhD program 2020 reference 0011-1408-2020-000008. Mikel Galar was partially supported by Tracasa Instrumental S.L. under projects OTRI 2018-901-073, OTRI 2019-901-091 and OTRI 2020-901-050.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Lithium-ion second-life batteries: aging modeling and experimental validation

  • Pérez Ibarrola, Ane
  • San Martín Biurrun, Idoia
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
Re-utilizing lithium-ion batteries from electric vehicles reduces their environmental impact. To ensure their optimal sizing and safe use, identifying the current state of the battery and predicting its remaining useful life is essential. This work analyzes the degradation mechanisms involved and proposes an aging model that utilizes a semi-empirical approach to accurately reproduce the battery's state of health within a range of 75-45 %. Calendar aging includes dependencies on temperature and state of charge while cycling aging is modeled based on depth of discharge, medium SOC, temperature, and Crate. The model is validated against experimental data from 14 LMO/LNO cells previously used in actual Nissan Leaf vehicles and an RMSE bellow 2.5 % is achieved in every case., This work is part of the projects PID2022-139914OB-I00, funded by MICIU/ AEI/10.13039/501100011033/ and by 'ERDF/EU' , TED2021-132457BI00, funded by MICIU/AEI/10.13039/501100011033/ and by the European Union 'NextGenerationEU/PRTR', STARDUST (H2020-SCC-2016/17- 774094), funded by the European Union's Horizon 2020 research and innovation program, HYBPLANT (0011-1411-2022-000039), funded by the Government of Navarre, and Lion2H2 (PJUPNA2023-11380), funded by the Public University of Navarre.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Delimitación inteligente de áreas homogéneas para un riego de precisión: un sistema web basado en clustering

  • Fernández Oregi, Xabier
  • Bellosta Diest, Amelia
  • Preciados, Miguel
  • Campo-Bescós, Miguel
La gestión eficiente del riego agrícola se ve limitada por la heterogeneidad del suelo y la falta de herramientas accesibles para integrar datos complejos. Este estudio presenta un sistema web automático que divide parcelas en sectores de riego de igual superficie, considerando variables edáficas, topográficas, hidrológicas e índices espectrales. Utiliza algoritmos de agrupación y análisis espacial para identificar zonas homogéneas, procesando datos públicos como pendiente, orientación, índice de vegetación en el infrarrojo cercano (NIRv), índice de humedad topográfica (TWI) y conductividad hidráulica saturada (Ks). Validado en tres parcelas cerealistas de Navarra, el sistema demuestra alta precisión y estabilidad. Su diseño modular y basado en software libre permite a técnicos y agricultores acceder fácilmente a información geoprocesada. En conclusión, se automatiza la sectorización agronómica, ofreciendo una solución útil para optimizar el diseño de riego y avanzar hacia una gestión hídrica de precisión más eficiente., Efficient irrigation management in agriculture is often constrained by soil heterogeneity and the lack of accessible tools to integrate complex data. This study presents an automated web-based system that divides agricultural plots into equal-area irrigation sectors, considering edaphic, topographic, hydrological, and vegetation spectral variables. The tool applies clustering algorithms and spatial analysis to identify homogeneous zones, processing public datasets such as slope, aspect, near-infrared vegetation index (NIRv), topographic wetness index (TWI), and saturated hydraulic conductivity (Ks). Validated on three cereal plots in Navarra (Spain), the system demonstrates high precision and spatial stability. Its modular design, based on open-source software, enables technicians and farmers to easily access geoprocessed information. In conclusion, the system successfully automates agronomic sectorization, offering a practical solution to optimize irrigation layout and advance towards more efficient precision water management., Amelia Bellosta ha recibido financiación del Gobierno de Navarra a través del programa de Doctorados Industriales 2024 (Expediente 0011-1408-2024-000029). Los autores desean agradecer la colaboración y soporte de Daniel Huarte e Iñigo Barberena. Miguel Ángel Campo gratefully acknowledges the support of the European Union through the Path4Med Project (Project ID 101156867), funded under the HORIZON MISS-2023-OCEAN-SOIL-01-01 call of the Horizon Europe Programme.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Enhancing DreamBooth with LoRA for generating unlimited characters with stable diffusion

  • Pascual Casas, Rubén
  • Maiza Coupin, Adrián Mikel
  • Sesma Sara, Mikel
  • Paternain Dallo, Daniel
  • Galar Idoate, Mikel
This paper addresses the challenge of generating unlimited new and distinct characters that encompass the style and shared visual characteristics of a limited set of human designed characters. This is a relevant problem in the audiovisual industry, as the ability to rapidly produce original characters that adhere to specific characteristics greatly increases the possibilities in the production of movies, series, or video games. Our solution is built upon DreamBooth, a widely extended fine-tuning method for text-to-image models. We propose an adaptation focusing on two main challenges: the impracticality of relying on detailed image prompts for character description and the few-shot learning scenario with a limited set of characters available for training. To solve these issues, we introduce additional character-specific tokens to DreamBooth training and remove its class-specific regularization dataset. For an unlimited generation of characters, we propose the usage of random tokens and random embeddings. This proposal is tested on two specialized datasets and the results shows our method¿s capability to produce diverse characters that adhere to a style and visual characteristics. An ablation study to analyze the contributions of the proposed modifications is also developed., This work has been funded by MCIN/AEI/10.13039/501100011033/FEDER, UE, with the project PID2022-136627NB-I00, by the Government of Navarre under the project 0011-1365-2022-000130, and by the Public University of Navarra under the project PJUPNA2023-11377. The Scary and Virus datasets are designed by Freepik. This research received support from an FPU grant (Formación de Profesorado Universitario) awarded by the Spanish Ministry of Science and Innovation (MCINN) to Rubén Pascual.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Impact of micro-cycles on the lifetime of lithium-ion batteries - EIS analysis

  • Nováková, Katerina
  • Berrueta Irigoyen, Alberto
  • Soto Cabria, Adrián
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
Publicado 2024-07-30, Experimental studies of lithium-ion batteries are very often based only on deep charge and discharge cycles. However, these test profiles do not fully reflect the actual operation of the battery in an electric vehicle or in stationary applications, where the battery is not only loaded during the main charging and discharging profiles, but it is also stressed by the current throughput caused by renewable power fluctuations or by auxiliary services. These cycles, which are superimposed to the main charge and discharge processes and have a depth of discharge not exceeding 2%, are called micro-cycles. Although there are several simulation studies that attempt to capture this issue, there is still no comprehensive experimental study that has the phenomena that occur during micro-cycling. This paper presents an experimental analysis of micro-cycles, providing a detailed view of the different processes taking place in the battery during aging, by means of a detailed analysis of the results from electrochemical impedance spectroscopy (EIS). By studying the single electrochemical processes in detail, this paper explains the benefits of micro-cycling in terms of extending the lifetime of the battery., This research was funded by the Czech Technical University student's grant project number SGS24/136/OHK3/3T/13 and by the project 'The Energy Conversion and Storage', funded as project No. CZ.02.01.01/00/22-008/0004617 by Programme Johannes Amos Comenius, call Excellent Research. Moreover, this work is part of the projects PID2022-139914OB-I00, funded by MCIN/AEI/10.13039/501100011033/FEDER, UE, TED2021-132457B-I00, funded by MCIN/AEI/10.13039/501100011033/ and by the European Union NextGenerationEU/PRTR, and HYBPLANT (0011-1411-2022-000039), funded by Government of Navarre.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Optimized pattern design of a light guide using 2D ray-tracing simulation

  • Medrano Gurrea, Mario
  • Jiménez Martínez, Unai
  • Tainta Ausejo, Santiago
  • Erro Betrán, María José
  • Arnedo Gil, Israel
  • Beato López, Juan Jesús
  • Izura, J.
  • Zabala, Silvia
We propose the use of a simplified model for the analysis of the scattering elements used in edge-lit systems. By modelling their behaviour as lambertian light sources whose properties depend on the size and geometry of the scatterer and LGP, it is possible to simulate the illuminance map of the edge-lit structure using only 2D ray-traced simulation. This reduces the computational complexity in the optimisation process used to calculate the scatterers distribution to achieve maximum uniformity in light extraction. The results obtained by comparison between the proposed algorithm and a commercial software demonstrate the validity of the proposal., This work was supported by the Government of Navarre through project 7-Lights (0011-1365-2021-000137).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

A new genetic algorithm approach for hybrid-domain spectral signature design

  • Duque Madrid, Nathalia
  • Gómez Laso, Miguel Ángel
  • Luna, Francisco
  • Pons Abenza, Alejandro
  • Lopetegui Beregaña, José María
  • Arregui Padilla, Iván
  • Arnedo Gil, Israel
  • Sánchez Pérez, Arancha
  • Zabala, Silvia
  • Trébol, Eduardo
  • Álvarez Botero, Germán Andrés
This paper presents a Genetic Algorithm (GA)-based methodology for designing high-capacity spectral signature tags for chipless RFID applications. By integrating Frequency Shift Keying (FSK) and Amplitude Shift Keying (ASK), the proposed method enables hybrid-domain encoding, increasing bit capacity without additional resonators. The tags, fabricated using high-resolution screen printing, were experimentally validated through S-parameter measurements, demonstrating strong correlation with simulations. The results show a maximum bit capacity of 12.59 bits, a spectral bit capacity (SBC) of 4.2 bits/GHz, and a spatial bit density (SBD) of 1.57 bits/cm², achieving a balance between spectral efficiency and compact design. Comparative analysis with state-of-the-art solutions highlights the method's potential for anticounterfeiting, secure identification, and high-density RFID applications., We acknowledge the financial support from the Navarra Government, through the Dirección General de Energía, I+D+I Empresarial y Emprendimiento (Project 0011-1365-2024-000033), and the Ministry of Science and Innovation - State Research Agency (MCIN/AEI/10.13039/501100011033), Spain, under Project PID2020-112545RB-C53. Furthermore, Germán Álvarez-Botero acknowledges the support of the Navarra Government through the Andia Fellowship.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Multi-temporal data augmentation for high frequency satellite imagery: a case study in Sentinel-1 and Sentinel-2 building and road segmentation

  • Ayala Lauroba, Christian
  • Aranda Magallón, Coral
  • Galar Idoate, Mikel
Semantic segmentation of remote sensing images has many practical applications such as urban planning or disaster assessment. Deep learning-based approaches have shown their usefulness in automatically segmenting large remote sensing images, helping to automatize these tasks. However, deep learning models require large amounts of labeled data to generalize well to unseen scenarios. The generation of global-scale remote sensing datasets with high intraclass variability presents a major challenge. For this reason, data augmentation techniques have been widely applied to artificially increase the size of the datasets. Among them, photometric data augmentation techniques such as random brightness, contrast, saturation, and hue have been traditionally applied aiming at improving the generalization against color spectrum variations, but they can have a negative effect on the model due to their synthetic nature. To solve this issue, sensors with high revisit times such as Sentinel-1 and Sentinel-2 can be exploited to realistically augment the dataset. Accordingly, this paper sets out a novel realistic multi-temporal color data augmentation technique. The proposed methodology has been evaluated in the building and road semantic segmentation tasks, considering a dataset composed of 38 Spanish cities. As a result, the experimental study shows the usefulness of the proposed multi-temporal data augmentation technique, which can be further improved with traditional photometric transformations., Christian Ayala was partially supported by the Government of Navarra under the industrial Ph.D. program 2020 reference 0011-1408-2020-000008. Mikel Galar was partially supported by Tracasa Instrumental S.L. under the project OTRI 2020- 901-156, and by the Spanish MICIN (PID2019-108392GB-I00 / AEI / 10.13039/501100011033).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Mid-air contactless haptics to augment VR experiences

  • Ezcurdia Aguirre, Íñigo Fermín
  • Fernández Ortega, Unai Javier
  • Olaz Moratinos, Xabier
  • Marzo Pérez, Asier
We present four technologies to deliver contactless haptic stimuli for enriching Virtual Reality (VR) experiences. The technologies are electrostatic piloerection, focused light-induced heat, electric plasma, and ultrasound; the user does not require to wear or touch any device. We describe the working principle behind each technology and how these technologies can provide new exciting sensations in VR experiences. Additionally, we showcase a VR demo experience gathering all four remote haptic stimuli along a circuit for the users to experiment with these new sensations., This research was funded by the EU Horizon 2020 research and innovation programme No 101017746 TOUCHLESS, by the European Research Consortium No 101042702 Intevol-ERC2021-STG, and by Gobierno de Navarra Fondo Europeo de Desarrollo Regional GymTar 0011-1365-2022-000085.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

AI training for application to industrial robotics: trajectory generation for neural network tuning

  • Merino Olagüe, Mikel
  • Ibarrola Chamizo, Javier
  • Aginaga García, Jokin
  • Hualde Otamendi, Mikel
In the present work robot trajectories are generated and kinematically simulated. Different data (joint coordinates, end effector position and orientation, images, etc.) are obtained in order to train a neural network suited for applications in robotics. The neural network has the goal of automatically generating trajectories based on a set of images and coordinates. For this purpose, trajectories are designed in two separate sections which are conveniently connected using Bezier curves, ensuring continuity up to accelerations. In addition, among the possible trajectories that can be carried out due to the different configurations of the robot, the most suitable ones have been selected avoiding collisions and singularities. The designed algorithm can be used in multiple applications by adapting its different parameters., This work was funded by the “Convocatoria de ayudas a proyectos de I+D del Gobierno de Navarra” under the projects with Ref. 0011–1365-2021–000080 and Ref. 0011–1411-2021–000023.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Short single strand DNA detection by means of Lossy Mode Resonance based fiber-optic sensor

  • Zubiate Orzanco, Pablo
  • Ciáurriz Gortari, Paula
  • Tellechea Malda, Edurne
  • Santano Rivero, Desiree
  • Del Villar, Ignacio
  • Urrutia Azcona, Aitor
  • Arregui San Martín, Francisco Javier
  • Matías Maestro, Ignacio
  • Ruiz Zamarreño, Carlos
Development of DNA and RNA biosensors and the associated diagnostic tests have gained growing interest in recent years. In particular, short RNA chains (around 25 oligonucleotides), known as micro RNAs, can be associated different stroke and neurodegenerative diseases. Here, we present the utilization of highly sensitive fiber optic sensor based on Lossy Mode Resonance (LMR) for the detection of single strand complementary DNA (ssDNA) associated to Huntington disease (Hsa-miR-34b)., This work was supported by the Spanish Ministry of Economy and Competitiveness TEC2016-78047-R, and Government of Navarra (0011-1365-2017-000117) (PC095-096 OPTISENS) and Public University of Navarra (PJUPNA26) research grants. In addition, this project has received funding from the ATTRACT call financed by the European Union's Horizon 2020 research and innovation programme under grant agreement No 777222.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Generación ilimitada de personajes mediante Stable Diffusion con DreamBooth y LoRA

  • Pascual Casas, Rubén
  • Maiza Coupin, Adrián Mikel
  • Sesma Sara, Mikel
  • Paternain Dallo, Daniel
  • Galar Idoate, Mikel
Este artículo aborda el reto de generar un número ilimitado de personajes nuevos, y distintos, que engloben el estilo y las características visuales compartidas de un conjunto limitado de personajes diseñados por un humano. Este es un problema de gran relevancia en la industria audiovisual, ya que la capacidad de producir rápidamente personajes originales que se adhieran a unas características específicas aumenta enormemente las posibilidades en la producción de películas, series o videojuegos. Nuestra solución se basa en DreamBooth, un método de ajuste de modelos generativos de texto a imagen ampliamente extendido. Proponemos una adaptación centrada en dos retos principales: lo poco práctico que resulta utilizar prompts detallados de las imágenes para describir los personajes y la complejidad del ajuste de modelos a partir de un conjunto limitado de personajes. Para resolver estos problemas, introducimos en el entrenamiento de DreamBooth tokens adicionales específicos para cada personaje y eliminamos el conjunto de datos de regularización. Para generar personajes de manera ilimitada, proponemos el uso de tokens y embeddings aleatorios. Comprobamos la utilidad de la propuesta utilizando dos conjuntos de datos diferentes. Los resultados obtenidos muestran la capacidad de nuestro método para producir personajes diversos que se adhieren a un estilo y a unas características visuales concretas. Finalmente, desarrollamos un estudio de ablación., Este trabajo está financiado por MCIN/AEI/10.13039/501100011033/FEDER, UE, con el proyecto PID2022-136627NB-I00, por el Gobierno de Navarra bajo el proyecto 0011-1365-2022-000130, y por la Universidad Pública de Navarra bajo el proyecto PJUPNA2023-11377. Los conjuntos de datos Scary y Virus están diseñados por Freepik. Esta investigación ha contado con el apoyo de una beca FPU concedida por el Ministerio de Ciencia e Innovación de España (MCINN) a Rubén Pascual.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Monitoreo inmersivo en tiempo real del suelo en viñedos usando realidad virtual

  • Klaina, Hicham
  • Bellosta Diest, Amelia
  • Iturri López, Peio
  • Picallo Guembe, Imanol
  • Falcone Lanas, Francisco
  • Campo-Bescós, Miguel
Este artículo presenta una aplicación avanzada de Realidad Virtual (VR) diseñada para mejorar la gestión de viñedos mediante la visualización inmersiva y el monitoreo en tiempo real de la humedad y temperatura del suelo a cuatro profundidades críticas: 10, 20, 30 y 40 cm. El sistema consiste en varios sensores con comunicación SDI-12, colocados estratégicamente en parcelas de viñedo. Los valores medidos se transmiten con conectividad NB-IoT cada 20 minutos y se recuperan de forma segura a través de una API, visualizándose dentro de un entorno detallado de VR desarrollado en Unity. La aplicación VR integra seguimiento de manos, interacciones por rayos y contacto, teletransportación, gráficos de indicadores en tiempo real, gráficos históricos, análisis de agua acumulada y visualización intuitiva de profundidades del suelo. El sistema propuesto, que puede utilizarse remotamente, proporciona beneficios significativos a los agricultores, incluyendo una mejor interpretación de datos, toma de decisiones optimizada y gestión eficiente de recursos. Lo que se traduce en una mayor productividad y sostenibilidad del viñedo., This article presents an advanced Virtual Reality (VR) application designed to improve vineyard management through immersive visualization and realtime monitoring of soil moisture and temperature at four critical depths: 10, 20, 30, and 40 cm. The system consists of several sensors with SDI-12 communication, strategically placed in vineyard fields. The measured values are transmitted via NB-IoT connectivity every 20 minutes and securely retrieved through an API, being visualized within a detailed VR environment developed in Unity. The VR application integrates hand tracking, ray and touch interactions, teleportation, real-time indicator charts, historical graphs, accumulated water analysis, and intuitive visualization of soil depths. The proposed system, which can be used remotely, provides significant benefits to farmers, including improved data interpretation, optimized decision-making, and efficient resource management, resulting in increased vineyard productivity and sustainability., El Gobierno de Navarra ha financiado la contratación de Amelia Bellosta en el marco de la convocatoria de ayudas "Doctorados Industriales 2024 (Nº Expediente: 0011-1408-2024-000029). Esta investigación fue financiada por el proyecto Path4Med, bajo el programa HORIZON (Project ID: 101156867), en el marco del proyecto Path4Med HORIZON-MISS-2023-OCEAN-SOIL-01-01, financiado por la Unión Europea.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

El agrocompostaje como solución basada en la naturaleza para el reciclaje de los residuos orgánicos: experiencia piloto con alumnado de FP

  • González Moreno, Miguel Ángel
  • García Gracianteparaluceta, Beñat
  • Prieto Cobo, Eduardo
  • Seco Meneses, Andrés
Una Solución Basada en la Naturaleza (SBN) puede definirse como aquellas acciones en las cuales se emplean los principios de la naturaleza para dar solución a un problema medio ambiental. El compostaje se podría definir como esa solución natural para la transformación biológica de los residuos orgánicos en un producto de alto valor añadido denominado compost. Por lo tanto, esta técnica de reciclaje permite ‘cerrar el círculo’ en aplicación de una economía circular y contribuir en la lucha frente al cambio climático. Por primera vez en España, a través de la Comunidad Valenciana (ORDEN 4/2022, de 24 de marzo), se ha definido legalmente el agrocompostaje como todo aquel proceso de compostaje de subproductos y residuos procedentes de forma directa o indirecta de la actividad agrícola, ganadera y forestal, incluyendo como ingredientes exógenos a la explotación a aquellos materiales tradicionalmente usados para la actividad agrícola como estiércoles o, destríos y subproductos de la actividad trasformadora de los productos vegetales en el ámbito local y de autoconsumo. La presente comunicación pretende mostrar las conclusiones de la experiencia piloto de agrocompostaje realizada a través de un aprendizaje basado en un caso práctico con alumnado de un centro de formación profesional de la rama agraria desde dos puntos de vista: Por un lado, la parte puramente científico-técnica del proceso, dando a conocer los resultados obtenidos fruto del ensayo de agrocompostaje llevado a cabo con varios productos: subproductos agroindustriales de lavanda y lúpulo y residuos de café, en solitario y mezclados, en diversas proporciones de forma sistemática, con estiércol procedente de la explotación ganadera del propio centro educativo. Y por el otro, una parte más socioeducativa, queriendo mostrar desde un punto más 14 subjetivo, las vivencias, dificultades y preocupaciones del proceso de aprendizaje del alumnado mencionado como ‘maestros compostadores’ durante la duración del ensayo., Gobierno de Navarra y el Fondo Europeo de Desarrollo Regional a través del Programa Operativo FEDER 2014-2020 de Navarra: Vermicompostaje 4.0 (0011-1365-2019-000110)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Accurate State Space grid-following inverter model for small signal stability analysis in converter based power systems

  • Goñi Pérez, Naiara
  • Marcos Álvarez, Javier
  • García Solano, Miguel
  • García Barace, Alberto
  • Marroyo Palomo, Luis
  • Urtasun Erburu, Andoni
The future grid is expected to be mostly based on renewable energy plants, such as wind farms or solar plants, as well as hybrid power plants combining both technologies. As these technologies need a power inverter coupling, new dynamic interactions produced between each other arise, affecting the current stability of the grid. For that reason, there is an urgent need of developing simulation models, capable of analyzing these stability challenges, with a compromise between computational cost and accuracy. Previous studies validate the fidelity in terms of stability of a traditional grid-following inverter using nonlinear Averaged Electromagnetic Transient models with low simulation time, compared to nonlinear Switching Electromagnetic Transient models with high accuracy and high computational cost. This paper proposes a further implementation of the Averaged model, linearizing its behaviour by a State Space representation and using the same validation procedure focused on small signal stability, ensuring the high-fidelity approach of the State Space model. Additionally, it is shown how the State Space representation provides new insights in modal analysis, being able to study analytically the stability of the system in the frequency domain, understanding how the control variables are affecting the system stability and reducing the complexity of simulating multiple inverters. Therefore, the grid-following State Space model becomes the best choice for this type of stability studies., This investigation is supported by the Spanish State Research Agency (AEI) under grant PID2022-142179OB-I00 and the Government of Navarre under grant 0011-1408-2022-000002.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Gender stereotyping impact in facial expression recognition

  • Domínguez Catena, Iris
  • Paternain Dallo, Daniel
  • Galar Idoate, Mikel
Facial Expression Recognition (FER) uses images of faces to identify the emotional state of users, allowing for a closer interaction between humans and autonomous systems. Unfortunately, as the images naturally integrate some demographic information, such as apparent age, gender, and race of the subject, these systems are prone to demographic bias issues. In recent years, machine learning-based models have become the most popular approach to FER. These models require training on large datasets of facial expression images, and their generalization capabilities are strongly related to the characteristics of the dataset. In publicly available FER datasets, apparent gender representation is usually mostly balanced, but their representation in the individual label is not, embedding social stereotypes into the datasets and generating a potential for harm. Although this type of bias has been overlooked so far, it is important to understand the impact it may have in the context of FER. To do so, we use a popular FER dataset, FER+, to generate derivative datasets with different amounts of stereotypical bias by altering the gender proportions of certain labels. We then proceed to measure the discrepancy between the performance of the models trained on these datasets for the apparent gender groups. We observe a discrepancy in the recognition of certain emotions between genders of up to 29 % under the worst bias conditions. Our results also suggest a safety range for stereotypical bias in a dataset that does not appear to produce stereotypical bias in the resulting model. Our findings support the need for a thorough bias analysis of public datasets in problems like FER, where a global balance of demographic representation can still hide other types of bias that harm certain demographic groups., This work was funded by a predoctoral fellowship of the Research Service of Universidad Publica de Navarra, the Spanish MICIN (PID2019-108392GB-I00 and PID2020-118014RB-I00 / AEI / 10.13039/501100011033), and the Government of Navarre (0011-1411-2020-000079 - Emotional Films).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

La gestión de residuos orgánicos agroindustriales como propuesta de mitigación del cambio climático, Agroindustrial organic waste management as a proposal for climate change mitigation

  • González Moreno, Miguel Ángel
  • García Gracianteparaluceta, Beñat
  • Prieto Cobo, Eduardo
El aumento de la información sobre cambio climático en los medios, de manera más acentuada en el último lustro, va de la mano de un creciente interés académico por analizar la comunicación sobre los que los geólogos denominan la nueva era del antropoceno. El III Congreso de Comunicación en Cambio Climático (CCCC 2022) fue un evento que tuvo lugar los días 27 y 28 de octubre de 2022 en Sevilla (de forma presencial) y Madrid (virtual), bajo con el título: Comunicando soluciones (En inglés: Communicating solutions). El evento, que fue coorganizado por la Facultad de Comunicación de la Universidad de Sevilla y la Facultad de Ciencias de la Información de la Universidad Complutense de Madrid, tuvo como objetivo el de generar un espacio académico donde los distintos agentes implicados en los procesos comunicativos sobre el cambio climático cooperen e intercambien herramientas, investigaciones y metodologías en este área., Gobierno de Navarra y el Fondo Europeo de Desarrollo Regional a través del Programa Operativo FEDER 2014-2020 de Navarra: Vermicompostaje 4.0 (0011-1365-2019-000110)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Experimental characterization and aging analysis of commercial 18650 sodium-ion cells

  • Irujo Izcue, Elisa
  • Berrueta Irigoyen, Alberto
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
Extensive use of lithium-ion batteries and scarcity of lithium are leading to re-emergence of sodium-ion batteries as a promising candidate, side-by-side with LIBs, to cover increasing demand of energy storage systems. Thus, development and commercialization of SIBs have been recently accelerated. Scientific research on first commercialized cells has been published regarding its fundamental parameters, aging and thermal performance. However, SIBs still require experimental study to continue developing and maturing their technology. For that reason, this work presents an electrical characterization and aging analysis of a commercial 1.3 Ah 18650 SIB. Based on experimental results obtained, this contribution reveals energy efficiencies of around 92% and an open circuit voltage with a plateau at a SOC of 35%. Regarding aging, samples full cycled at 0.5C exhibit a capacity loss of 15% after 310 cycles and stored cells age at a speed of 0.01 %/day., This work is part of the projects PID2022-139914OB-I00, funded by MICIU/ AEI/ 10.13039/501100011033/ and by 'ERDF/EU', TED2021-132457BI00, funded by MICIU/AEI/10.13039/501100011033/ and by the European Union 'NextGenerationEU/PRTR', STARDUST (H2020-SCC-2016/17-774094), funded by the European Union's Horizon 2020 research and innovation program, HYBPLANT (0011-1411-2022-000039), funded by the Government of Navarre, Lion2H2 (PJUPNA2023-11380), funded by the Public University of Navarre, and has also been supported by the Public University of Navarra under a Ph.D. scholarship.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Economía circular para el sector primario: el vermicompostaje como técnica de valorización de residuos orgánicos agroindustriales

  • González Moreno, Miguel Ángel
La sala de conferencias del edificio Jerónimo de Ayanz acogió el 31 de mayo de 2024 la jornada doctoral "Valorización de residuos orgánicos e inorgánicos en el marco de la economía circular“ organizada por el Instituto de Materiales Avanzados y Matemáticas (INAMAT2) de la Universidad Pública de Navarra y la Escuela de Doctorado de Navarra (EDONA). La valorización de residuos desde diferentes puntos de vista y con distintas aplicaciones es uno de los aspectos estratégicos en la economía circular. En esta breve jornada se trató de presentar el interés de esta valorización y algunos ejemplos aplicados tanto para el caso de residuos de componente orgánica como inorgánica. En el marco de este evento tuvo lugar la ponencia del investigador Miguel Ángel González Moreno, bajo el título "Economía circular para el sector primario: El vermicompostaje como técnica de valorización de residuos orgánicos agroindustriales", con el objetivo de mostrar el trabajo de investigación del uso de lombrices para compostar algunos residuos orgánicos., Gobierno de Navarra y el Fondo Europeo de Desarrollo Regional a través del Programa Operativo FEDER 2014-2020 de Navarra: Vermicompostaje 4.0 (0011-1365-2019-000110)
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

A novel ku-band circularly-polarized horn antenna based on a ridged wall

  • Marzo Oyarbide, Andoni
  • Teberio Berdún, Fernando
  • Teniente Vallinas, Jorge
In this paper, a novel wideband (31.5 % bandwidth) circularly-polarized antenna based on a ridged wall is presented. A pair of ridges on the inner wall of the horn serves as an inbuilt polarizer, which can generate left-hand or right-hand circular polarization without any additional polarizer. The ridged wall is placed at 45° with respect to the input port linearly polarized wave to generate a 90° phase delay and obtain the desired circular polarization at the aperture. The simulated results show that the antenna works great in the whole Ku satellite band (from 10.7 to 14.7 GHz) with more than 20 dB return loss and below 1 dB axial ratio. The antenna can be fabricated using traditional computer numerical control machining techniques or the new 3D metal additive manufacturing processes., This research was co-funded by the Navarra Government under project 0011-1408-2021-000004 and project 0011-1365-2021-000220.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Alfalfa quality detection by means of VIS-NIR optical fiber reflection spectroscopy

  • Ruiz Zamarreño, Carlos
  • Gracia Moisés, Ander
  • Vitoria Pascual, Ignacio
  • Imas González, José Javier
  • Castaño de Egüés, Lorena Yveth
  • Avedillo de la Casa, Amaia
  • Matías Maestro, Ignacio
A first approach study for the classification of alfalfa (medicago sativa) quality has been performed by means of VIS-NIR optical fiber reflection spectroscopy. Reflection spectral data has been obtained from alfalfa samples comprising six different qualities. Obtained data has been classified and organized to feed supervised self-learning algorithms. Neural networks have been used in order to differentiate the quality level of the samples. Obtained results permit to validate the proposed approach with 72% of the samples properly classified. In addition, proposed solution was implemented in a low cost automated detection prototype suitable to be used by non-qualified operators. Obtained equipment consist of a first step towards its utilization in quality monitoring and classification of many other products in the agri-food field., This work was supported by the Spanish Ministry through FPU18/03087 and PID2019-106231RB-I00 grants, Government of Navarra 0011-1365-2021-000065 and 0011-1408-2021-000007 grants and UPNA-ISC PhD grant.
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Authentication of cattle finishing diets (conventional vs. vegetable by-products) using near-infrared spectroscopy

  • León Ecay, Sara
  • López Maestresalas, Ainara
  • Goenaga Uceda, Irantzu
  • Mendizábal Aizpuru, José Antonio
  • Insausti Barrenetxea, Kizkitza
This study explored the potential of a portable near-infrared (NIR) spectrophotometer (1200 - 2200 nm; 2-nm bandwidth) to discriminate meat and carcasses from cattle fed two different diets: a control of 90% barley and 10% straw (C, n = 12) and, a ration including 37.5% of vegetable by-products (VBPR, n = 11). At 24 h postmortem spectra were collected on the exterior surface of the left carcass, first, between the 5th and 6th ribs, and afterwards, on the 12th and 13th ribs. After fabrication and 7 d of aging, spectral data was acquired from the intact steaks while keeping muscle integrity. When spectra were collected from the carcasses, partial least squares-discriminant analysis (PLS-DA) correctly classified (%CC) >66.67% in both Train and cross-validation (CV) whereas radial basis function-support vector machine (RBF-SVM) discriminated 100 - 83.33% in Train and CV, respectively, using the full spectrum. Reducing the initial matrix ((λ=501) by interval-PLS (iPLS) led into a >75% of well-sorted carcasses by finishing diet while RBFSVM increased the %CC up to >83.33%. Using both discriminant approaches, carcasses were authenticated with a subtle improvement over intact meat (>90% vs. >75% in Train and >80% vs. >65% in CV for C and VBPR, respectively). Variable importance in projection (VIP) scores showed how variables >1592 nm had higher weight in the discrimination process. The results achieved showed the potential of NIR technology as a sustainable, fast and chemical-free tool to assist the integration of the meat industry into the digital age of connectivity and digitization., This research has been founded by the Government of Navarra and the European Regional Development Fund via project BEEF+ 'Carne saludable a través de la economía circular' (0011-1365-2020-000288), by Universidad Pública de Navarra through a PhD scholarship UPNA-2022 (Res.2178/2022) and, an Industrial PhD 2020 scholarship from the Government of Navarra (0011-1408-2020-000009).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

Experimental evaluation of the safety performance of lithium-ion batteries based on abuse areas

  • Lalinde Sainz, Iñaki
  • Berrueta Irigoyen, Alberto
  • Valera, Juan José
  • Arza, Joseba
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
Safety issues associated with lithium-ion batteries (LIBs) jeopardize their widespread adoption in both stationary applications and electric vehicles. One of the factors that can most affect the safety of a LIB is its chemistry. For this reason, this article aims to evaluate the safety of the two main current chemistries, LFP and NMC. In particular, the safety of both technologies is examined from the perspective of the areas of abuse that characterize their behavior beyond the safe operation area. A commercial 5 Ah pouch cell with LFP chemistry is subjected to various overtemperature and overcharge abuses at different conditions. The results obtained for LFP chemistry cell are discussed together with those for NMC cell from a previous work of the authors. Identification of the abuse areas allows for a comparative analysis of the safety of both chemistries, providing a valuable tool for classifying the abuse behavior of LIBs., This work is part of the projects PID2022-139914OB-I00, funded by MICIU/AEI/ 10.13039/501100011033/ and by 'ERDF/EU', TED2021-132457BI00, funded by MICIU/AEI/10.13039/501100011033/ and by the European Union 'NextGenerationEU/PRTR', STARDUST (H2020-SCC-2016/17-774094), funded by the European Union's Horizon 2020 research and innovation program, HYBPLANT (0011-1411-2022-000039), funded by the Government of Navarre, and has also been supported by the Spanish Ministry of Science and Innovation under a Ph.D. scholarship (PRE2020-095314).
Academica-e. Repositorio Institucional de la Universidad Pública de Navarra
Publication Contribución de congreso (ConferenceOutput)

On the technical reliability of lithium-ion batteries in a zero emission polar expedition

  • Soto Cabria, Adrián
  • Berrueta Irigoyen, Alberto
  • Sanchis Gúrpide, Pablo
  • Ursúa Rubio, Alfredo
  • Oficialdegui, Ignacio
This contribution presents a technical analysis of the Lithium-ion batteries (LIBs) used in the WindSled project. In this project, an expedition has been carried out by means of a 0-emission vehicle that have covered more than 2500 kilometers in Antarctica Eastern Plateau pulled by kites. This adventure allowed the performance of 10 scientific experiments with a minimal disturbance of the polar environment. The required electricity for the survival and the scientific experimentation was delivered by flexible PV panels installed on the sled and commercial LIBs. The study performed in this contribution aims at the quantification of the LIBs degradation after the expedition. The results show a capacity fade of 5 % and an internal resistance increase of 30 %. Based on these results, it can be claimed that the LIBs used in the WindSled Project can successfully operate under -40°C. Moreover, these batteries can be used in upcoming expeditions, entailing an improvement from an economical and environmental point of view compared to primary batteries., Spanish State Research Agency (AEI) and FEDER-UE under grants DPI2016-80641-R, DPI2016-80642-R, PID2019-111262RB-I00 and PID2019-110956RB-I00, the Government of Navarra through research project 0011-1411-2018- 000029 GERA and the Public University of Navarre under project ReBMS PJUPNA1904.