Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Rapid Laser-Based Deposition of PbI2/CsBr Inorganic Scaffolds for Hybrid Fabrication of Perovskite/Silicon Tandem Solar Cells

  • Kralj, Suzana
  • Artuk, Kerem
  • Nales, Marly
  • Hnapovskyi, Vladyslav
  • Minguez-Avellan, Miriam
  • Vishal, Badri
  • Said, Ahmed Ali
  • De Wolf, Stefaan
  • Wolff, Christian M.
  • Morales-Masis, Monica
  • Boix, Pablo P.|||0000-0001-9518-7549
[EN] Rapid dry deposition of metal halide perovskites and inorganic scaffolds remains a key challenge for scalable vapor-phase fabrication. Here, we demonstrate fast vapor-phase growth of PbI2/CsBr inorganic scaffolds from a single composite target using pulsed laser deposition. Deposition rates exceeding 100 nm min-1, over an order of magnitude higher than comparable co-evaporated scaffolds, enable the deposition of similar to 540 nm-thick PbI2/CsBr inorganic scaffolds on textured silicon cells within 5 min. The PbI2/CsBr ratio is moreover maintained from the source target to the film, and the process delivers high material utilization. Proof-of-concept 1 cm2 fully textured perovskite/silicon tandem cells are demonstrated with the rapid PLD scaffolds converted with an organohalide solution to perovskite absorbers and passivated with piperazinium iodide. The material and device characterization demonstrates that laser-based vapor deposition is a promising route for rapid inorganic scaffold fabrication., This project was funded by the European Research Council (ERC) under the European Union s Horizon 2020 Research and Innovation Program (CREATE, Grant Agreement No.852722), received by M.M.M., and the SolarLab within SolarNL, a national research, innovation and industrial development program funded by The Netherlands National Growth Fund. S.K., M.M.M., K.A., and C.M.W. acknowledge additional funding from the European Union s Horizon 2020 Research and Innovation Program (VIPERLAB, Grant No. 101006715, VLAB-234-00137). K.A. and C.M.W. further acknowledge funding from the Swiss State Secretariat for Education, Research and Innovation (SERI) (TRIUMPH, 101075725), the Swiss National Science Foundation (Radicals, CRSII5_216647), the Swiss Federal Office of Energy (PRESTO, PERSISTARS, BESTOBOT), and the ETH Domain through an AM grant (AMYS). P.P.B. and M.M.A. acknowledge support from the predoctoral contract PRE2021- 099951, funded by MCIN/AEI/10.13039/501100011033 within the project PID2020-119628RB-C31.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Mitigating the amorphization of perovskite layers by using atomic layer deposition of alumina

  • Kedia, Mayank
  • Das, Chittaranjan
  • Kot, Malgorzata
  • Yalcinkaya, Yenal
  • Zuo, Weiwei
  • Tabah, Kenedy
  • Matvija, Peter
  • Ezquer, Mikel
  • Cornago, Iñaki
  • Hempel, Wolfram
  • Kauffmann, Florian
  • Plate, Paul
  • Lira-Cantú, Mónica
  • Weber, Stefan A.L.
  • Saliba, Michael
Atomic layer deposition of aluminum oxide (ALD-Al<inf>2</inf>O<inf>3</inf>) layers has recently been studied for stabilizing perovskite solar cells (PSCs) against environmental stressors, such as humidity and oxygen. In addition, the ALD-Al<inf>2</inf>O<inf>3</inf> layer acts as a protective barrier, mitigating pernicious halide ion migration from the perovskite towards the hole transport interface. However, its effectiveness in preventing the infiltration of ions and additives from the hole-transport layer into perovskites remains insufficiently understood. Herein, we demonstrate the deposition of a compact ultrathin (∼0.75 nm) ALD-Al<inf>2</inf>O<inf>3</inf> layer that conformally coats the morphology of a triple-cation perovskite layer. This promotes an effective contact of the hole transporter layer on top of the perovskite, thereby improving the charge carrier collection between these two layers. Upon systematically investigating the layer-by-layer structure of the PSC, we discovered that ALD-Al<inf>2</inf>O<inf>3</inf> also acts as a diffusion barrier for the degraded species from the adjacent transport layer into the perovskite. In addition to these protective considerations, ALD-Al<inf>2</inf>O<inf>3</inf> impedes the transition of crystalline perovskites to an undesired amorphous phase. Consequently, the dual functionality (i.e., enhanced contact and diffusion barrier) of the ALD-Al<inf>2</inf>O<inf>3</inf> protection enhanced the device performance from 19.1% to 20.5%, while retaining 98% of its initial performance compared to <10% for pristine devices after 1500 h of outdoor testing under ambient conditions. Finally, this study deepens our understanding of the mechanism of ALD-Al<inf>2</inf>O<inf>3</inf> as a two-way diffusion barrier, highlighting the multifaceted role of buffer layers in interfacial engineering for the long-term stability of PSCs., M. S., M. K., and C. D. thank Helmholtz Young Investigator Group FRONTRUNNER. M. S., Y. Y., and S. W. thank the German Research Foundation (DFG) for funding (SPP2196, 431314977/GRK 2642). M. S. and M. L. C. acknowledge the funding from ProperPhotoMile. Project ProperPhotoMile is supported under the umbrella of SOLARERA.NET co-funded by The Spanish Ministry of Science and Education and the AEI under Project PCI2020-112185 and CDTI Project IDI-20210171; the Federal Ministry for Economic Affairs and Energy based on a decision by the German Bundestag Projects FKZ 03EE1070B and FKZ 03EE1070A and the Israel Ministry of Energy with Project 220-11-031. SOLAR-ERA.NET is supported by the European Commission with the EU Framework Programme for Research and Innovation HORIZON 2020 (Cofund ERA-NET action number 786483), funded by the European Union. M. S. acknowledges funding from the European Research Council under the Horizon Europe Program (LOCAL-HEAT, Grant Agreement 101041809). M. S. acknowledges funding from the German Bundesministerium für Bildung and Forschung (BMBF), project “NETPEC” (01LS2103E). M. S. also acknowledges funding by the Deutsche Forschungsgemeinschaft (German Research Foundation) via the project “Correlating Defect Densities with Recombination Losses in Halide-Perovskite Solar Cells.” The authors gratefully acknowledge the core facility SRF AMICA (Stuttgart Research Focus Advanced Materials Innovation and Characterization) at the University of Stuttgart for their support and assistance. This research was supported by the German Research Foundation (DFG, AOBJ: 661806). M. Kot and P. P. acknowledge the funding from Zentrales Innovationsprogramm Mittelstand (ZIM), Federal Ministry of Economics and Climate Protection Project no KK5087602BR1. M. S., M. K., and C. D. acknowledge the CERIC-ERIC Consortium for access to experimental facilities and financial support (proposal number 20232163). P. M. is grateful for the partial financial support provided by the Czech Ministry of Education, Youth and Sports (project LM2023072). M. K. and M. S. also acknowledge the VIPERLAB project financed by the European Union's Horizon 2020 (grant agreement No. 101006715). M. K. thanks Eugenia Zugasti and Javier Diaz Berrade from CENER, Spain, for their assistance during the MPPT measurements. M. K. also acknowledges Ludwig Marth from SENTECH for technical assistance during ALD deposition., Peer reviewed