Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A critical evaluation of platinum deposition techniques for hydrogen production in microbial electrolysis cells

  • Sánchez Peña, Pilar|||0000-0002-7825-4890
  • Rodriguez, Jesús|||0000-0002-8601-0466
  • Baeza, Juan Antonio|||0000-0003-1290-1669
  • Gabriel, David|||0000-0002-7713-4192
  • Guisasola, Albert|||0000-0002-3012-7964
  • Baeza, Mireia|||0000-0002-2240-6410
Despite its high cost, Pt is the usual catalyst for hydrogen production in the cathode of Microbial Electrolysis Cells (MECs). Its effectiveness depends not only on the amount deposited but also on the availability and distribution of Pt nanoparticles on the cathode surface. This work provides a comprehensive study of the effectiveness of the Pt coating with five deposition techniques: spray, electrospray, brush painting, doctor blade and sputtering. The performance of the cathodes was studied with different Pt loadings by monitoring the current intensity and H2 production in MECs. Furthermore, cathodes were characterized morphologically using scanning electron microscopy together with energy-dispersive X-ray spectroscopy to study their Pt surface distribution and composition. Sputtering was initially discarded due to Pt detachment. When using the same amount of Pt (0.50 mg Pt cm-2), the highest current density was obtained for electrospray (2.0 mA cm-2), followed by spray (1.9 mA cm-2), brush painting (1.6 mA cm-2) and doctor blade (1.2 mA cm-2). Hence, electrospray improved 20 % the results obtained by the default method of brush painting. Electrospray and spray provided better performance because of the direct deposition of Pt on the carbon fibres creating a compact Pt layer on the electrode surface. Furthermore, it was observed that the cell performance decreased significantly with decreasing amount of Pt per cm2, observing the best performance with the highest Pt load tested (0.5 mg Pt cm-2) regardless of the deposition technique.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Less is more, a comprehensive study on the effects of the unmber of gas diffusion layers on air-cathode microbial fuel cells

  • Sánchez Peña, Pilar|||0000-0002-7825-4890
  • Rodriguez, Jesús|||0000-0002-8601-0466
  • Montes, Raquel|||0000-0001-8805-9987
  • Baeza, Juan Antonio|||0000-0003-1290-1669
  • Gabriel, David|||0000-0002-7713-4192
  • Baeza, Mireia|||0000-0002-2240-6410
  • Guisasola, Albert|||0000-0002-3012-7964
Air-cathode microbial fuel cells (AC-MFC) use a gas-diffusion-layer (GDL) coating based on polytetrafluoroethylene applied to the cathode to prevent electrolyte leakage. However, this type of GDL can also lead to a decrease in MFC performance due to electron-transfer limitation, mass-transfer limitation or catalyst availability. This study provides a comprehensive understanding of the significance of the GDL coating, demonstrating the interaction between the number of GDL coatings and the external resistance (Rext) used. An experimental design in 28 mL AC-MFCs was prepared and conducted using two different Rext (10 and 249 Ω) and four different GDL coatings (1 to 4 layers). The coating effect was not significant when operating with a high Rext, where the electron transfer was the limiting process. However, when the Rext was low, the amount of polytetrafluoroethylene limited the cathode performance due to a significant decrease in the Pt availability on the catalytic surface. Thus, GDL-1 with 10 Ω as Rext reached 0.96 mA/cm2, 3-fold higher than that obtained with 249 Ω as Rext (ca. 0.30 mA/cm2). Besides, the current density did not vary noticeably in the other cathodes with 249 Ω as Rext. Contrarily, the current density with 10 Ω as Rext decreased as the number of GDL increased (0.74, 0.57 and 0.37 for GDL-2, GDL-3 and GDL-4 respectively). These values agreed with those of the polarization curve. Furthermore, limitations were also observed in electrochemical impedance spectroscopy measurements: the charge resistance increased with the number of GDL, related to the ease of electron flow. These values were18 Ω, 22 Ω, 53 Ω and 58 Ω for GDL-1, GDL-2, GDL-3 and GDL-4, respectively, for both 10 and 249 Ω cathodes.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Graphene functionalization with metallic Pt nanoparticles, A path to cost-efficient H2 production in microbial electrolysis cells

  • Sánchez Peña, Pilar|||0000-0002-7825-4890
  • Rodriguez, Jordi
  • Gabriel, David|||0000-0002-7713-4192
  • Baeza, Juan Antonio|||0000-0003-1290-1669
  • Guisasola, Albert|||0000-0002-3012-7964
  • Baeza, Mireia|||0000-0002-2240-6410
Platinum is one of the most widely used catalysts in the cathode of Microbial Electrolysis Cells (MECs) to overcome the relatively slow kinetics of hydrogen evolution, even though it is not economically feasible on a large scale. This work aims at developing, applying, characterizing, and optimizing two novel Pt-functionalized inks with promising characteristics: Pt@rGO based on reduced graphene oxide and Pt@Graphitene based on a home-made material named Graphitene, which showed improved performance at a lower cost. The Pt-functionalized materials were deposited on carbon cloth and used as cathode electrode in a single chamber MEC. These materials provided 47% increase in Pt functionalization over commercial inks. Moreover, surface areas of 10.76 m/g and 24.40 m/g and electroactive areas of 0.10 cm/cm and 0.16 cm/cm were determined for Pt@Graphitene and Pt@rGO, respectively, a difference caused by structural defects in the case of the Pt@rGO, which slightly improved its performance compared to Pt@Graphitene. Thus, the experimental results reached ca. 0.8 mA/cm, a 43% higher intensity than that obtained using conventional commercial inks.