Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 37
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Synthesis of Sr(1-x-y)Al4O7:Eux2+, Lny3+ (Ln= Dy, Y, Pr) Nanophosphors Using Rapid Gel Combustion Process and Their Down Conversion Characteristics

  • Singh, Devender
  • Tanwar, Vijeta
  • Samantilleke, Anura Priyajith
  • Bhagwan, Shri
  • Singh, Krishan Chander
  • Kadyan, Pratap Singh
  • Marí, B.|||0000-0003-0001-419X
  • Singh, Ishwar
[EN] Eu2+ and Eu2++Ln3+ doped SrAl4O7 nanophosphors were synthesized by rapid gel combustion process. The morphology of prepared phosphors was examined with scanning and transmission electron microscopy. The phase identification and the crystal structures of nanophosphors were studied using X-ray powder diffraction techniques. Luminescence characteristics of the prepared nanophosphors were analyzed on account of excitation, emission and phosphorescence decay analysis. The emission spectra demonstrated the broad green emission attributed to 4f65d1→ 4f7 transition of the Eu2+ ions. The effect of codoping of some trivalent lanthanide (Dy3+, Pr3+ and Y3+) ions were investigated for improving the emission intensity and phosphorescence decay time of the basic lattice of SrAl4O7:Eu2+ phosphors. The synthesized materials had enhanced bright luminescent properties that could suitably be applied for display as well as photovoltaic applications. Devender Singh, Vijeta Tanwar, Anura P. Samantilleke, Bernabe Mari, Shri Bhagwan, Krishan C. Singh, Pratap S. Kadyan, Ishwar Singh, The authors thankfully recognize the financial support from the University Grant Commission (UGC), New Delhi [MRP-40-73/2011(SR)] and the European Commission through Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

p-type behavior of electrodeposited ZnO:Cu thin films

  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Sahal, Mustapha
  • Cerqueira, F.M.
  • Samantilleke, Anura Priyajith
Cu-doped ZnO (ZnO:Cu) thin films and ZnO/ ZnO:Cu homojunction devices were electrodeposited on conductive glass substrates in a non-aqueous electrolyte containing Cu and Zn salts. The Cu content of the films is proportional to the Cu/Zn precursor ratio in the deposition electrolyte. ZnO:Cu was found to be of a hexagonal wurtzite structure with (002) preferred orientation. A transition from n-type to p-type was observed for ZnO:Cu films with a Cu/ Zn ratio higher than 2% as inferred from the change in the direction of the photocurrent. The rectifying characteristics shown by homojunction devices further confirm the p-type conductivity of ZnO:Cu layers., This work was supported by the Spanish Government through MEC grant MAT2009-14625-C03-03 and the Portuguese Foundation for Science and Technology (FCT), CIENCIA 2007. Financial support by the European Commission through NanoCIS project (PIRSESGA-2010-269279) is gratefully acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Red emitting MTiO3 (M = Ca or Sr) phosphors doped with Eu3+ or Pr3+ with some some cations as co-dopants

  • Marí, B.|||0000-0003-0001-419X
  • Singh, Krishan Chander
  • Cembrero Coca, Paula
  • Singh, I.
  • Singh, D.
  • Chand, S.
[EN] Ca (or Sr)TiO3:Eu3+ , M (Li + or Na+ or K+ ) and CaTiO3:Pr 3+ , M (Li + or Na+ or Ag+ or K+ or Gd3+ or La3+ ) powders were prepared by combustion synthesis method and the samples were further heated to !1000 !C to improve the crystallinity. The structure and morphology of materials were examined by X-ray diffraction (XRD) and a scanning electron microscopy (SEM). The morphologies of SrTiO3:Eu3+ , CaTiO3:Eu3+ or CaTiO3:Pr 3+ powders co-doped with other metal ions were very similar. Small and coagulated particles of nearly cubical shapes with small size distribution having smooth and regular surface were formed. Photo-luminescence spectra of CaTiO3:Pr 3+ and co-doped either with Li + , Na+ , K+ , Ag+ , La3+ or Gd3+ ions showed red emissions at 613 nm due to the 1 D2 ? 3 H4 transition of Pr 3+ . The variation of intensity of emission peak with different co-doping follows the order: K+ > Ag+ > Na+ > Li + > La3+ > Gd3+ . The characteristic emissions of CaTiO3:Eu3+ lattices had strong emission at 614 and 620 nm for 5 D0 ? 7 F2 with other weak transitions observed at 580, 592, 654, 705 nm for 5 D0 ? 7 Fn transitions where n = 0, 1, 3, 4 respectively in all host lattices. Photoluminescence intensity in SrTiO3:Eu3+ is more than CaTiO3:Eu3+ lattices. A remarkable increase of photoluminescence intensity (in 5 D0 ? 7 F2 transition) was observed if co-doped with Li + ions in CaTiO3:Eu3+ and SrTiO3:Eu3+ . " 2013 Elsevier B.V. All rights reserved., This work was supported by Spanish Government through MCINN Grant MAT2009-14625-C03-03 and the European Commission through NanoCIS Project (FP7-PEOPLE-2010-IRSES ref. 269279). K.C. Singh acknowledges MEC for financial support (SAB2010-0019).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

ZnO-based spinels grown by electrodeposition

  • Tortosa Jorques, María Dolores
  • Manjón, Francisco-Javier|||0000-0002-3926-1705
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
We report on the synthesis of thin films of ZnCo 2O 4 and ZnMn 2O 4 spinels, as well as pure Co 3O 4 and Mn 3O 4 spinels, by means of electrodeposition. Spinel thin films have been analyzed by energy dispersive spectroscopy, X-ray diffraction, and Raman spectroscopy. We show that under determined deposition conditions the initial wurtzite structure of Co- and Mn-doped ZnO develops into spinel structures when the Co and Mn concentration in the films is above the solubility limit of these ions in the typical ZnO-wurtzite structure. © 2012 Elsevier Ltd. All rights reserved., This work was supported by Spanish Government through MICINN grants MAT2009-14625-C03-03, MAT2010-21270-C04-04 and MALTA CSD2007-0045. Financial support by the European Commission through NanoCIS project (PIRSES-GA-2010-269279) is gratefully acknowledged. Finally, we also want to acknowledge the support of Vicerrectorado de Investigacion y Desarrollo de la Universitat Politecnica de Valencia through projects UPV2011-0914 PAID-05-11 and UPV2011-0966 PAID-06-11.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Synthesis and enhanced luminescent characterization&amp, #8232, of SrAl4O7:Eu2+,RE3+ (RE= Nd, Dy) nanophosphors for light emitting applications

  • Singh, D.
  • Tanwar, V.
  • Samantilleke, Anura
  • Marí, B.
  • Singh Kadyan, P.
  • Singh, Krishan Chander
[EN] SrAl4O7:Eu2+,RE3+ (RE = Nd, Dy) nanophosphors were efficiently synthesized with a facile fast gel com- bustion procedure in presence of air. During the synthesis process, urea was used as an organic fuel. Boric acid was applied as reducer as well as flux for the reduction of Eu3? ions into Eu2?. Phase composition, morphology and photolumi- nescence (PL) properties of the prepared SrAl4O7:Eu2?,RE3? phosphors were analyzed by X-ray diffraction, scanning electron microscopy (SEM), transmission electron micro- scopy (TEM) and PL techniques respectively. SEM results showed agglomeration with fluffy shapes having voids and pores and further nanostructural details were obtained with TEM. The divalent europium doped SrAl4O7 phosphors showed broad band emission spectra at 506 nm due to 8H3/2 - 8S7/2 transition on excitation at 360 nm. The pre"pared nanophosphors had high brightness and long afterglow properties which could be efficiently applied in variety of potential light emitting applications., The authors gratefully recognize the financial support from the University Grant Commission (UGC), New Delhi [MRP-40-73/2011(SR)] and the European Commission through Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Needs of multidisciplinary training for engineers: Efficiency, sustainability and profitability of Photovoltaic Energy Plants

  • Guaita-Pradas, Inmaculada|||0000-0003-4116-2375
  • Marí, B.|||0000-0003-0001-419X
[EN] New challenges are been imposed on the markets of developed and developing countries. On the one hand, it has come the phenomenon of globalization. And the other is the economic and environmental sustainability. In a world dominated by technology, engineers as mentors and supporters are expected to gear the decisions of companies’ investments. Besides the technical characteristics of any investment, project design usually involves its economic valuation and profitability analysis. So, to meet the multidisciplinary labor market demands, engineering students require some knowledge of economic analysis techniques to complete their education. In this study we use both capital budgeting and energy production techniques to analyze the yield of photovoltaic power plants. First of all, we describe the technical characteristics of a solar installation addressed to electricity production and we estimate the energy output, which mainly depends on the solar irradiation hitting the solar modules. Further, taking into account the energy production we apply capital budgeting techniques to assess the profitability of such investment. Regarding economics we describe the main concepts: the net present value, the internal rate of return and the payback. These are standard viability indicators to assess the profits and assist the investor in business decisions. These parameters are estimated for two photovoltaic power plants located in Spain and Gemany, which starts its production activity at present, without any kind of economic incentives. Indeed, the addition of capital budgeting techniques would expand the success chances in renewable energy projects., Authors are gratefully to European Commission for supporting this work through grant NanoCIS (FP7-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Control parameters on the fabrication of ZnO hollow nanocolumns

  • Cembrero Cil, Jesús
  • Busquets Mataix, David Jeronimo|||0000-0001-5031-7805
  • E. Rayón|||0000-0002-0653-2046
  • Pérez Puig, Miguel Angel
  • Marí, B.|||0000-0003-0001-419X
  • Pascual Guillamón, Manuel
[EN] The present work reports on the fabrication of hollow ZnO nanocolumns by a sequential combination of electrochemical deposition, chemical attack and regeneration. Initially, ZnO nanocolumns were deposited in two different substrates, namely Fluor Tin Oxide and Indium Tin Oxide. In a further step, a statistical analysis on the most influencing control parameters in the dissolution stage to produce the hollow ZnO nanowires on the FTO substrates was carried out. The control variables considered were electrolyte concentration, dissolution time and temperature, whereas the output variable was the percentage of the hollow nanocolumns obtained. The statistical analysis consisted of a two-level factorial design of experiments on three variables, therefore involving a series of 8 experiments. An analysis of variance (ANOVA) on the results was also carried out. The results showed that all the control variables were significant, the most important being the dissolution time., This work was supported by the Spanish Government through MCINN Grant MAT2009-14625-C03-03, Generalitat Valenciana programme PROMETEO/2009/063 and European Commission through NanoCIS project FP7-PEOPLE-2010-IRSES (ref. 269279). Technical support given to the authors by the Servei de Microscopia at the Universitat Politecnica de Valencia (Spain) is greatly acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrochemical Fabrication and Characterization of p-CuSCn/n-ZnO Heterojunction Devices

  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Singh, Krishan Chander
  • Ortiz Moya, Laura
[EN] p-CuSCN/n-ZnO heterojunction devices were prepared by depositing CuSCN electrochemically over a ZnO film previously deposited. The compact and smooth surface films of n-ZnO on FTO substrate were deposited electrochemically from a nonaqueous bath. The CuSCN films were characterized by cyclic voltammetry, chronoamperometry, SEM, energy-dispersive X-ray spectroscopy, and XRD measurements. The pure crystalline films of CuSCN with intrinsic trigonal pyramidal morphology over the ZnO films were obtained electrochemically by fixing the SCN/Cu ratio in the electrolytic bath 1.5:1 at 60 °C with −0.4 V deposition potential. Photocurrent measurements showed the increase of intrinsic surface states or defects in ZnO/CuSCN interface. The I V characteristic of p-CuSCN/n-ZnO heterojunctions shows good rectification behavior with a rectification ratio of 250 at ±2 V. The value of 2.81 of the ideality factor calculated by fitting the semilogarithmic I V data with the ideal diode equation revealed the better electrical contact between the smooth ZnO and CuSCN films than that of ZnO nano-rods and CuSCN crystallites., This work was supported by the Spanish Government through MCINN grant MAT2009-14625-C03-03 and European Commission through NanoCIS project FP7-PEOPLE-2010-IRSES (ref. 269279). K.C. Singh acknowledges MEC for the financial support (SAB2010-0019).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effective electrochemical n-type doping of ZnO thin films for optoelectronic window applications

  • Cembrero Coca, Paula
  • Singh, K.C.
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] An effective n-type doping of ZnO thin films electrochemically synthetized was achieved by varying the chloride ion concentration in the starting electrolyte. The ratio between chloride and zinc cations was varied between 0 and 2 while the zinc concentration in the solution was kept constant. When the concentration of chloride in the bath increases an effective n-type doping of ZnO films takes place. n-type doping is evidenced by the rise of donors concentration, obtained from Mott-Schottky measurements, as well as from the blueshift observed in the optical gap owing to the Burstein-Moss effect., This work was supported by Spanish Government through MCINN grant MAT2009-14625-C03-03 and European Commission through NanoCIS project FP7-PEOPLE-2010-IRSES (ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Chemical spray pyrolysis of β-In2S3 thin films deposited at different temperatures

  • Sall, Thierno
  • Hartitti, Bouchaib
  • Fahoume, Mounir
  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
In2S3 thin films were deposited onto indium tin oxide-coated glass substrates by chemical spray pyrolysis while keeping the substrates at different temperatures. The structures of the sprayed In2S3 thin films were characterized by X-ray diffraction (XFD). The quality of the thin films was determined by Raman spectroscopy. Scanning electron microscopy (SEM) and atomic force microscopy were used to explore the surface morphology and topography of the thin films, respectively. The optical band gap was determined based on optical transmission measurements. The indium sulfide phase exhibited a preferential orientation in the (0, 0, 12) crystallographic direction according to the XRD analysis. The phonon vibration modes determined by Raman spectroscopy also confirmed the presence of the In2S3 phase in our samples. According to SEM, the surface morphologies of the films were free of defects. The optical band gap energy varied from 2.82 eV to 2.95 eV., This research was supported by the Generalitat Valenciana through the grant PROMETEUS 2009/2013 and the European Commission through the Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Étude de la composition stechiometrique des couches minces de CdTe élaborées par électrodéposition pour des applications photovoltaïques

  • Soro, D.
  • Boko, Aka
  • Marí, B.|||0000-0003-0001-419X
[FR] Les couches minces de CdTe ont été préparées sur des substrats de Au / Al203 de dimensions d'environ (2X0,8 cm2), en utilisant la technique de l'électrodéposition. Les parametres étudiés au cours de la croissance des films sont la durée du dépot et la concentration du dioxyde de tellurure. L'analyse de la composition chimique des films a l'EDS a révélé une bonne strechiométrie (51 ,65% pour le cadmium et 48,35% pour le tellurure) pour un mélange réactionnel contenant 2. l 0-1 mol/L de chlorure de cadmium et de 4. l o·4mol/L de dioxyde de tellurure. La morphologie des films a été examinée a la microscopie électronique a balayage et jugée satisfaisante., [EN] Thin films of CdTe were prepared on substrates of Au / Al 203 cut in rectangular shaped (2X0,8 cm2) using the technique of the electrodeposition. The parameters studied during the film growth are the deposition time and the concentration of dioxide telluride. The analysis of the chemical composition of the films by EDS showed good stoichiometry (51.65% for cadmium and 48.35% for telluride) for a reaction mixture containing 2. l 0-1 mol / L of cadmium chloride and 4. l 0-4 mol / L dioxide telluride. The morphology of the films was examined in the scann ing electron microscopy and satisfactory., O. Soro remerde l'Etole Norma/e Supérieur tl'A/Jidjon pour lo /Jourse t¡u'el/e fui o otlroyée. {e lroroil effetlué entre tlons le totlre tl'un pro¡e1 finonté por le Gourernemenl Espognol (pro¡et MAT2009-l.f62J-COJ-OJ) et lo {ommission Européenne (Nono(JS pro¡et FPl-PEOPLE-2010-/ISE~ lel 269219).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Enhanced luminescence by tunable coupling of Eu3+ and Tb3+ in ZnAl2O4:Eu3+:Tb3+ phosphor synthesized by solution combustion method

  • Verma, Naveen
  • Singh, Krishan Chander
  • Jindal, Jitender
  • Yadav, Suprabha
  • Mittal, Anuj
  • Marí, B.|||0000-0003-0001-419X
[EN] ZnAl2O4:Eu3+ or Tb3+ (1 mol%) and ZnAl2O4:Eu3+/Tb3+ with varied concentrations of Eu3+ and Tb3+ were prepared by solution combustion method. The photoluminescence spectra of synthesized compounds shows that simultaneous doping of Tb3+ and Eu3+ causes enhancement in Eu3+ luminescence intensity. This indicates some energy transfer from Tb3+ to Eu3+. This phenomenon of Tb3+ -> Eu3+ energy transfer, accomplishing enhanced intensity of Eu3+ ions, is attributed to the cross relaxation phenomenon, which is favored by overlap between the donor and acceptor transition. The energy is transferred to Eu3+ cascade rapidly via non-radiative transitions to D-5(0) state. The synthesized compounds were characterized by XRD, SEM for their structural and morphological characteristics respectively., This work was supported by the European Commission through NanoCIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Endorse of renewable energy plants, still an alternative investment in Spain?

  • Guaita-Pradas, Inmaculada|||0000-0003-4116-2375
  • Marí, B.|||0000-0003-0001-419X
[EN] The development of renewable energy technologies depends on two main factors: progress of the related technologies and incentive policies. Long-term incentive policies are essential to achieve progress and spreading of clean energies. However, this scenario is not always met and in some countries some confusion emerge owing to the lack of stable incentive policies. This paper deals with the financial and economical analysis of a standard investment in renewable energy photovoltaic systems in Spain. Main investment parameters related to photovoltaic solar energy plants in Spain during the last decade have been analyzed. Net present value, payback and internal rate of return of a typical 20 kWp photovoltaic solar plant have been calculated in the frame of the recent history of energy policies in Spain. Despite the high variations of incentive policies withdrawn by renewable energy plants, we demonstrate that the evolution of related technology and market has been able to surpass the absence of long-term policies and even nowadays the photovoltaic systems can still be considered as a profitable investment from the economic point of view., This work was supported by European Commission through grant NanoCIS (FP7-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrochemical synthesis of hexagonal hollow ZnO nanostructures

  • Abellan Rubio, Mª Angeles
  • Moya Forero, Mónica Mercedes
  • Marí, B.|||0000-0003-0001-419X
[EN] A simple and controllable one-step electrodeposition process is proposed in order to obtain ZnO nanotubes. Zinc oxide thin films were grown on fluorine-doped tin oxide by electrodeposition from an aqueous electrolyte containing zinc nitrate and potassium nitrate. Generally, in aqueous electrolytes ZnO is electrochemically deposited in the form of hexagonal nanocolumns. These nanocolumns grow perpendicularly to the substrate until reaching a maximum height of about 2 µm and then the perpendicular growth vanishes and the solid nanocolumns develop to hexagonal hollow structures. Several characteristics of the electrodeposited films such as thickness, morphology and crystalline structure were obtained as a function of the deposited charge. The evolution of the morphology of the electrodeposited layers as a function of time was monitored by Scanning Electron Microscopy. X-Ray Diffraction confirms that hexagonal nanotubes are preferentially oriented along the (002) direction., This work was supported by CONICYT (project 3130451), Ministerio de Economía y Competitividad (project ENE2013-46624-C4-4-R) and European Commission through NanoCISproject FP7-PEOPLE-2010-IRSES (ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Pulse and potentiostatic electrodeposition of CuInSe2 films on gold coated alumina substrates

  • Valdés, M.
  • Vazquéz, M.
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] CuInSe2 thin films were deposited on goldcoated alumina electrodes using constant and pulsed potential signals. In situ electrochemical measurements were recorded with an atomic force microscope to follow CuInSe2 electrodeposition. The electrodeposited films were characterized employing scanning electron microscopy, energy dispersive spectroscopy, grazing incidence X-ray diffraction, and Raman spectroscopy. The best stoichiometry is attained for films deposited at pulsed potentials of -0.7 V. These films are also the most compact, showing a homogeneous morphology. In contrast, potentiostatic films presented minor variations in their chemical composition with the deposition potential. The morphology presented porous coral-like structures. X-ray and Raman spectroscopy analysis of as-deposited films by either technique reveal the presence of secondary phases such as CuxSe and Se, especially at the most positive deposition potentials. After a thermal treatment at 500 "C in Se vapor, the crystallinity of the material is significantly enhanced and no secondary phases are present., This study was partially supported by Spanish Government through MCINN grant MAT2009-14625-C03-03 and European Commission through NanoCIS project FP7-PEOPLE-2010IRSES (ref. 269279). Financial support from Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET), Agencia Nacional de Promocion Cientifica y Tecnologica and Universidad Nacional de Mar del Plata (UNMdP) from Argentina are greatly acknowledged. The authors wish to thank BSc. Mariela Desimone for her assistance with GXRD measurements.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sustainable development with photovoltaic energy in India and Pakistan

  • Guaita-Pradas, Inmaculada|||0000-0003-4116-2375
  • Marí, B.|||0000-0003-0001-419X
  • Ullah, Shafi
[EN] The development and massive use of renewable energy depends on two main factothe use of Reuse rs: progress of related technologies and dedicated incentive policies. Improvement of technology is highly dependent on the amount of founds dedicated to the related R&D. Long-term incentive policies that address favoring investment are also essential to achieve general progress and a widespread use of clean energies. However, the latter scenario is not always available and in some countries, and confusion emerges as stable incentive policies are lacking. In this paper we show a capital budgeting analysis of standard investments in renewable energy photovoltaic systems in two developing countries such as India and Pakistan. Standard profitability indicators, such as net present value, payback and internal rate of return, are applied to such investments. The production of electricity through solar energy is sustainable from both economical and ecological point of views. This can be an additional advantage for developing countries like India and Pakistan, as they have much of their electric network still under construction. Despite the lack of incentive policies, we show how the technology and the markets are nowadays enough mature to consider photovoltaic systems for electric energy production a profitable investment from an economic viewpoint., This work was supported by the European Commission through NanoCIS project (FP7-PEOPLE-2010-IRSES ref. 269279). One of the authors (S.Ullah) acknowledges Erasmus Mundus IDEAS Action-II for finantial support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Investigation on the Effect of Gallium on the Efficiency of CIGS Solar Cells through Dedicated Software

  • Ullah, Hanif
  • Cui, Hai-Ning
  • Marí, B.|||0000-0003-0001-419X
[EN] This work reports on the analysis of thin-film copper¿indium¿gallium¿diselenide (CIGS) solar cells by using Solar Cell Capacitance Simulator software (SCAPS). We have modeled a PV device, which consists in a CIGS absorber, a CdS buffer and a ZnO window layer. We have studied the behavior of CIGS absorber as a function of Gallium content by simulating the behavior of CIGS solar cells versus the Ga content in the absorber layer., This work was supported by Innovation and Design for Euro-Asian Scholars (IDEAS) Action-2 and Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279) funded by European Commission. The authors are indebted to School of Design Engineering (ETSID) and Institute of Design and Fabrication (IDF) at Universitat Politècnica de València for their continuous support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Caractérisation structurale et optique de couches minces de CdS elaborées par CBD

  • Soro, D.
  • Boko, A.
  • Marí, B.|||0000-0003-0001-419X
[FR] Des couches minces de CdS d'épaisseurs différentes ont été élaborées sur des substrats en verre et ITO par la technique CBD (dépôt par bain chimique) pour des applications photovoltaïques. Les investigations lors de l¿élaboration tournaient autour des paramètres température et durée du dépôt. La mesure des épaisseurs des couches s¿est faite grâce à un profilomètre. La cristallinité a été déterminée par diffraction de rayon X, la composition et la morphologie des films à l¿aide d¿un Microscope Electronique à Balayage équipé d¿un système de Spectrométrie à Dispersion d¿Energie (EDS). Un spectromètre à force atomique (AFM) a permis d¿analyser la rugosité des films et les spectres de transmission optique ont été étudiés dans la région spectrale de 300 nm à 900nm. Tous les films élaborés avaient une transmittance élevée (~ 60 - 80%). Le gap optique des différents films a été évalué à partir des spectres de transmission. L'énergie de la bande optique qui est fonction des conditions de dépôts a été jugée dans la gamme de 2,25 à 2,35 eV. Les films ont été recuits à 300 °C pendant 2 heures, ce qui a permis d¿améliorer la cristallinité. La température idéale a été de 60°C, quand au temps de dépôt il est fonction de l¿épaisseur désirée., D. Soro remercie l’Ecole Normale Supérieure d’Abidjan pour la bourse qu’elle lui a octroyée. Ce travail rentre dans le cadre d’un projet financé par le Gouvernement Espagnol (projetMAT2009-14625-C03-03) et la Commission Européenne (NanoCIS projet FP7-PEOPLE-2010-IRSES, Réf. 269279)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Luminescence properties of the Eu2+ /Eu3 + activated Barium aluminate phosphors with varies Gd3+ concentration

  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Singh, K.C.
  • Verma, Naveen
  • Jindal, Jitender
[EN] BaAl2O4:Eu2(+)/Eu3(+) (1mol %) co-doped with varying concentrations of Gd3(+) (1, 2, 5 and 10mol%) were prepared by combustion synthesis method at 600 degrees C. All the compositions were investigated for their structural and photoluminescence properties. Samples prepared in open atmosphere showed the presence of both Eu3(+) and Eu2(+) states which indicates the reduction of Eu3(+) to Eu2(+) during the preparation of these compounds. The prepared materials at 600 degrees C showed high intense broad peaks around 498nm corresponding to Eu2(+) and small peaks in the red region which are attributed to the presence of Eu3(+). In the 1000 degrees C annealed compounds, the intensity of the peak at 498nm got increased. The intensity of this broad band for BaAl2O4:Eu2(+)/Eu3(+)(1mol%):Gd3(+)(1mol%) was three times than that of BaAl2O4:Eu2(+)/Eu3(+)(1mol%). Thus second rare earth ion (Gd3(+)) acted as a good sensitizer and enhanced the photoluminescence intensity. The XRD spectra revealed the presence of hexagonal phase of BaAl2O4 as main phase and a small amount of a mixed phase Ba O! 6.6 Al2O3. Doping of Eu3(+), Gd3(+) did not change the crystalline structure of barium aluminate (BaAl2O4)., This work was supported by the Generalitat Valenciana through grant PROMETEUS 2009/2013 and the European Commission through Nano CIS project (FP7-PEOPLE2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Rapid synthesis and enhancement in down conversion emission properties of BaAl2O4:Eu2+,RE3+ (RE3+=Y, Pr) nanophosphors

  • Singh, Devender
  • Tanwar, Vijeta
  • Simantilke, Anura P.
  • Kadyan, Pratap S.
  • Singh, Ishwar
  • Marí, B.|||0000-0003-0001-419X
[EN] BaAl2O4:Eu2+,RE3+ (RE3+=Y, Pr) down conversion nanophosphors were prepared at 600 °C by a rapid gel combustion technique in presence of air using boron as flux and urea as a fuel. A comparative study of the prepared materials was carried out with and without the addition of boric acid. The boric acid was playing the important role of flux and reducer simultaneously. The peaks available in the XPS spectra of BaAl2O4:Eu2+ at 1126.5 and 1154.8 eV was ascribed to Eu2+(3d5/2) and Eu2+(3d3/2) respectively which confirmed the presence of Eu2+ ion in the prepared lattice. Morphology of phosphors was characterized by tunneling electron microscopy. XRD patterns revealed a dominant phase characteristics of hexagonal BaAl2O4 compound and the presence of dopants having unrecognizable effects on basic crystal structure of BaAl2O4. The addition of boric acid showed a remarkable change in luminescence properties and crystal size of nanophosphors. The emission spectra of phosphors had a broad band with maximum at 490–495 nm due to electron transition from 4f65d1 → 4f7 of Eu2+ ion. The codoping of the rare earth (RE3+=Y, Pr) ions help in the enhancement of their luminescent properties. The prepared phosphors had brilliant optoelectronic properties that can be properly used for solid state display device applications., The authors gratefully recognize the financial support from the University Grant Commission (UGC), New Delhi [MRP-40-73/2011(SR)] and the European Commission through Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Structural and optical properties of Ta2O5:Eu3+: Mg2+ or Ca2+ phosphor prepared by molten salt method

  • Verma, Naveen
  • Singh, Krishan Chander
  • Jindal, Jitender
  • Rana, Ravi
  • Pereira, A.L.J.
  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Manjón, Francisco-Javier|||0000-0002-3926-1705
. Ta2O5:Eu3+: Mg2+ or Ca2+ phosphor materials were prepared by molten salt method using KCl as flux. The Xray diffraction (XRD) patterns illustrated that the well crystallized Ta2O5:Eu3+: Mg2+ or Ca2+ were formed in the presence of flux under reduced temperature (800 ºC) in contrast to conventional solid state method (1200-1500 ºC). Scanning electron microscope (SEM) images indicate the achievement of well dispersed particles (hexagonal tablet and rod-like structures). Meanwhile, the photo-luminescent studies demonstrated that Ta2O5 is an efficient host to sensitize europium red emissions. The addition of Mg2+ or Ca2+ as co- dopant enhanced the luminescent intensity of Ta2O5: Eu3+ compound., This work was supported by the European Commission through Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Synthesis and down conversion emission property of Eu3+ doped LaAlO3 CsAlO2 and LiLaO2 phosphors

  • Marí, B.|||0000-0003-0001-419X
  • Singh, K. C.
  • Moya Forero, Mónica Mercedes
  • Singh, Ishwar
  • Om, Hari
  • Chand, Subhash
[EN] LaAlO3:Eu3+, CsAlO2:Eu3+ and LiLaO2:Eu3+ phosphors with varying concen- trations of Eu3+ from 3 to 10 mol% were prepared by combustion synthesis method and the samples were further heated to 1,000ºC to improve the crystallinity of the materials. The structure and morphology of materials have been examined by X-ray diffraction and scan- ning electron microscopy. SEM images depicted that the morphology of crystallites have no uniform shapes and sizes. Small and coagulated particles of irregular shapes of different sizes are obtained. The characteristic emissions of Eu3+ were clearly observed at nearly 580, 592, 650, 682 to 709 (multiplet structure) nm for 5D - 7 Fn transitions where n = 0, 1, 3, 4 respectively, including the strongest emission peaks at 614 and 620 nm for 5 D0 - 7 F2 transitions in CsAlO2:Eu3+ and LiLaO2:Eu3+ host lattices. The intensity of emission peak corresponding to 5 D0 !→ 7 F1 transitions in LaAlO3 :Eu3+ material is comparable to that of 5D0 5D-7F2 transitions which is also a singlet. Photoluminescence intensity follows the order as in LiLaO2 > LaAlO3 > CsAlO2 lattices. Remarkable high photoluminescence intensity with 7 mol% doping of Eu3+ in LiLaO2 makes it a strong contender for red colored display applications., This work was supported by the European Commission through Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

ZnTe thin films grown by electrodeposition technique on FTO substrates

  • SKHOUNI, OTHMANE
  • El Manouni, Ahmed
  • Schrebler, R.
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] Zinc telluride (ZnTe) thin films are prepared potentiostatically from an aqueous solution bath containing ZnCl2, TeCl4 and LiCl on Fluorine Tin Oxide coated glass substrate to investigate its suitability as a material for solar cell technology. The appropriate potential region where formation of stoichiometric ZnTe semiconductor occurs is found to be close to −0.85 V versus Ag/AgCl. X-ray diffraction results have indicated that all electrodeposited films have cubic structure. Quantitative analysis of energy dispersive X-ray analysis results has shown that the composition ratio (Zn:Te) of films is around (1:0.99). A direct energy gap of 2.19 eV is determined by NIR–Vis– UV spectroscopy. The effect of annealing on the crystallinity and optical properties has been reported. Impedance measurements have revealed that all grown films present a p-type electrical conductivity with acceptor density NA=2.16×1019 cm−3. Furthermore, the impedance results are adjusted to an equivalent circuit having two capacitors in series (Helmholtz, CH and space charge, CSC) and two resistances RCT and RSC, which are associated with charge transfer processes., This work was supported by the Spanish Government through AECI grant AP/035039/11 and the European Commission through Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Profitability and sustainability of photovoltaic energy plants in Spain

  • Guaita-Pradas, Inmaculada|||0000-0003-4116-2375
  • Marí, B.|||0000-0003-0001-419X
  • Bartual Sanfeliu, Concepción
[EN] This paper reports on capital budgeting analysis to assess investments in renewable energy photovoltaic systems in Spain. Standard profitability indicators such as net present value, payback time and internal rate of return are applied to such investments. Two main issues have been taken into account: the changes taking place in the recent history of energy policies in Spain as well as the evolution of related technologies. Despite variation in incentive policies, we show how both technology and market have been able to overcome the lack of long-term policies, and even nowadays, photovoltaic energy systems can still be regarded as a profitable investment from an economic viewpoint, even in absence of any kind of incentive., This work was supported by the European Commission through a Nano CIS Project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Preparation and Photoluminescence Properties of SrAl2O4:Eu2+,RE3+ Green Nanophosphors for Display Device Applications

  • Singh, Devender
  • Tanwar, Vijeta
  • Samantilleke, Anura P.
  • Bhagwan, S.
  • Kadyan, Pratap Singh
  • Singh, Ishwar
  • Marí, B.|||0000-0003-0001-419X
[EN] An efficient rapid gel combustion process was used to prepare divalent-eu- ropium-doped strontium aluminate (SrAl2O4:Eu2+/Eu2+,Dy3+/Eu2+,Dy3+,Nd3+) nanophosphors in the presence of boron flux in air. The prepared nanophos- phors emitted green light at 507 nm upon excitation at 360 nm. The emission of green light was observed due to the 4f65d1 fi 4f7 transition of Eu2+ ions. The absence of the characteristic sharp emission peak at 612 nm for Eu3+ (5D0 fi 7F2) indicates that efficient reduction of Eu3+ to Eu2+ occurred in the presence of the boron flux (H3BO3) as reducing agent. The x-ray diffraction pattern suggested monoclinic crystallinity, while transmission electron mi- croscopy revealed the average size of the prepared materials to be between 20 nm and 50 nm. Coactivators in the lattices such as Dy3+ alone or Dy3+ with "Nd3+ produced long persistence and enhancement of the optoelectronic prop- erties of the prepared materials., The authors gratefully recognize the financial support from the University Grant Commission (UGC), New Delhi [MRP-40-73/2011(SR)] and European Commission through Nano CIS Project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Luminescence Properties of CaAl2O4:Eu3+, Gd3+ Phosphors Synthesized by Combustion Synthesis Method

  • Verma, Naveen
  • Singh, K.C.
  • Jindal, Jitender
  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
[EN] CaAl2O4:Eu3+ (1 mol.%) co-doped with varying concentration of Gd3+ (1, 2, 5, and 10 mol.%) were prepared by combustion synthesis method at 600 C and further annealed at 1000 ºC. All the compositions were investigated for their structural and photoluminescence properties. It was observed that both states of europium i.e. Eu3+ and Eu2+ were present and ratio of these states changes on heating at 1000 ºC. The materials synthesized at 600 ºC showed high intense peak around 440 nm due to presence of Eu2+ and less intense peaks in the red region which were due to presence of Eu3+. On annealing the compounds at 1000 ºC, intensity of peak around 440 nm decreases and intensity of peaks in the red region increases significantly. The 5D0 !7 F3 transition due to Eu3+ at 657 nm appears as the highest intensity peak. All co-doped samples annealed at 1000 ºC showed the higher intensity than the mono doped sample which is due to energy transfer from the Gd3+ to Eu3+. The second rare-earth ion (Gd3+) acts as sensitizer and enhances the photoluminescence intensity. The X-ray diffraction spectra reveal the monoclinic phase of CaAl2O4 in all the samples which showed that Eu3+ and Gd3+ do not change the crystalline structure of calcium aluminate., This work was supported by the Generalitat Valenciana through grant PROMETEUS 2009/2013 and the European Commission through Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279)., This work was supported by the Generalitat Valenciana through grant PROMETEUS 2009/2013 and the European Commission through Nano CIS project (FP7- PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optical properties of Yb3+ doped ZnO/MgO nanocomposites

  • Marí, B.|||0000-0003-0001-419X
  • Jindal, J.
  • Singh, Krishan Chander
  • Verma, Naveen
[EN] Yb3þ doped ZnO/MgO nanocomposite were prepared by combustion synthesis method. The samples were further heated to 1000 °C to improve their crystallinity and photoluminescent efficiency. The concentrations of Yb3þ and Mg2þ were varied between 1–2% and 5–70% respectively in prepared samples. The nano-powders were characterized by Scanning Electron Microscopy and X-ray Diffraction for morphology and structural determination. XRD studies have revealed the wurtzite structure for MgxZn1"xO for Mg concentrations below 30%. Higher concentrations of Mg results in Yb3þ doped ZnO/ MgO nanocomposite containing three phases; the wurzite hexagonal phase typical of ZnO, the cubic phase of MgO and a small amount of cubic Yb2O3 phase. As expected, the amount of cubic phase in nanopowders increased with the increase of Mg concentration in ZnO. The crystallite size of ZnO/MgO composites decreased from 55 nm to 30 nm with increase of Mg content. SEM images of Yb3þ doped ZnO/MgO nanocomposite with higher Mg content (450%) showed clearly distinct hexagonal and cubical shaped nano-particles. Photoluminescent emission showed a broad band in the range (435 nm to 700 nm). Pure ZnO nano-phosphor showed an emission peak around 545 nm, which is blue shifted with Mg content. The photoluminescence intensity increased with increase of Mg content in ZnO and it became maximum with 30% Mg concentration. Time resolved decay curves of photoluminescence indicated decay time in microsecond time scale, This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R), Generalitat Valenciana (PROMETEUS-II/2014/044) and the European Commission through NanoCIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Baseline of numerical simulations for ZnTe based thin-film solar cells

  • Ullah, Hanif
  • Ullah, Shafi
  • Marí, B.|||0000-0003-0001-419X
Abstract Numerical modelling of photovoltaic solar cells is an important strategy to test the viability of proposed physical structures and their performance. This article introduces the concept of numerical simulation and explain the relevant physical models for the inside physical phenomenon like generation, recombination and transport of charge carriers (holes and electrons) in photovoltaic materials. This will made with essential input parameters, to have consistent and acceptable results. It is extremely useful to have a common baseline or starting point for researchers working on the same problem under different conditions irrespective of the place, group, research environment and tools/software used. The numerical work, hence produces results for fitting of modelling output to experimental results, predicting the effect of changes in material properties and geometry of cell performance and testing the viability of proposed physical device. A case-study for baseline parameter sets are presented that describes ZnTe based thin-film solar cells consist in ZnO/n-CdS/p-ZnTe in a substrate sequence. This model can be used as a baseline for more complicated models and will help photovoltaic researchers for enhancing the efficiency and reduction the costs in $/Wp of photovoltaic devices., This work was supported by the European Commission through the Erasmus Mundus Innovation and Design for EuroAsian Scholars-Action 2 Programme and FP7-PEOPLE-2010- IRSES-NanoCIS project.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Pulsed Electrodeposition of Tin Sulfide Thin Films from Dimethyl Sulfoxide Solutions

  • Burgos, A.
  • Cataño, F.
  • Schrebler, R.
  • Gomez, H.
  • Marí, B.|||0000-0003-0001-419X
[EN] SnS thin films were prepared on molybdenum covered glass substrates by pulsed electrodeposition. The structure, morphology and composition were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis and Raman spectroscopy. Highly compact, dense, homogenous and almost stoichiometric films were obtained by properly selecting the electrodeposition parameters. Capacitance-voltage measurements showed that the films are p-type presenting cathodic photocurrent under visible light illumination at a bias potential close to the flatband potential. (C) 2016 The Electrochemical Society. All rights reserved., H. G., R. S., B. Mari acknowledge to European Commission, NanoCIS project FP7-PEOPLE-2010-IRSES grant 269279, A. B. acknowledge FONDECYT (Fondo de Desarrollo Cientifico y Tecnologico, Chile) through Project No 3160217. FONDEQUIP EQM130170 project is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Preparation and luminescence properties of MZrO3:Eu3+, A+ (M=Ca2+ or Ba2+ and A=Li+ or Na+ or K+ ) phosphors with perovskite structure

  • Marí, B.|||0000-0003-0001-419X
  • Cembrero Coca, Paula
  • Singh, K.C.
  • Kaushik, R.D.
  • Om, Hari
[EN] Calcium and barium zirconate powders based upon CaZrO3:Eu3 +,A and BaZrO3:Eu3 +,A (A=Li+ , Na+, K+) were prepared by combustion synthesis method and heating to ~1000 °C to improve crystallinity. The structure and morphology of materials were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM). XRD results showed that CaZrO3:Eu3 +,A and BaZrO3:Eu3 +,A (A=Li+ , Na+ , K+ ) perovskites possessed orthorhombic and cubic structures, respectively. The morphologies of all powders were very similar consisting of small, coagulated, cubical particles with narrow size distributions and smooth and regular surfaces. The characteristic luminescences of Eu3+ ions in CaZrO3:Eu3+,A (A=Li+, Na+, K+) lattices were present with strong emissions at 614 and 625 nm for 5D0→7F2 transitions with other weaker emissions observed at 575, 592, 655, and 701 nm corresponding to 5D0→7Fn transitions (where n=0, 1, 3, 4, respectively). In BaZrO3:Eu3 + both the 5D0→7F1 and 5D0→7F2 transitions at 595 and 613 nm were strong. Photoluminescence intensities of CaZrO3:Eu3+ samples were higher than those of BaZrO3:Eu3+ lattices. This remarkable increase of photoluminescence intensity (corresponding to 5D0→7Fn transitions) was observed in CaZrO3:Eu3 + and BaZrO3:Eu3 + if co-doped with Li + ions. An additional broad band composed of many peaks between 440 to 575 nm was observed in BaZrO3:Eu3 + ,A samples. The intensity of this band was greatest in Li+ co-doped samples and lowest for K+ doped samples., The project was supported by the Spanish Government through MCINN (MAT2009-14625-C03-03) and European Commission through Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The influence of cadmium ions source on the morphology, structural and optical properties of CdS thin films

  • Soro, D.
  • Aka, B.
  • Calixto, M. Estela
  • Marí, B.|||0000-0003-0001-419X
[EN] Thin films of cadmium sulfide (CdS) have been prepared on ITO substrates by chemical bath deposition (CBD) technique using cadmium chloride (CdCl2), or cadmium sulfate (CdSO4) as cadmium ions source and thiourea as sulphur ions source. In a previous paper [1], we proposed the preparation of CdS layers deposited by chemical bath deposition using cadmium chloride (CdCl2) for CIS and CIGS thin film solar cells. Our goal is to provide a comprehensive study on the effect on film thickness, grain size, crystal structure and surface morphology. The growth was mainly controlled by the ion-by-ion growth mechanism, or by cluster-by-cluster mechanism. Various properties of the films, such as optical transmission, surface morphology and the X-ray diffraction patterns were studied. The scanning electron microscope results revealed that the morphology of the CdS was homogeneous. The X-ray diffraction results showed the film structure was a mixture of two phases: hexagonal and cubic. Optical transmission measurements have been done at room temperature with unpolarized light at normal incidence in the wavelength range from 300nm to 900nm., This work was supported by the Generalitat Valenciana through grant PROMETEUS 2009/2011 and the European Commission through Nano CIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical analysis of SnS based polycrystalline solar cells

  • Ullah, Hanif
  • Marí, B.|||0000-0003-0001-419X
[EN] SnS is a promising nontoxic and earth-abundant material suitable for photovoltaic applications. Photovoltaic solar cells based on tin sulphide absorbers have been analysed by using Solar Cell Capaci- tance Simulator software. The photovoltaic cell consists of SnS absorber layer, CdS as buffer and ZnO as optical window following the sequence p-SnS/CdS/ZnO. After optimization of different parameters and layer thicknesses a maximum efficiency of 10.6%, VOC of 0.92 V, JSC of 13.4 mA/cm2 and Fill Factor of 86.3% were reached. Simulation studies by varying several solar cell parame- ters such as thickness of various layers reveal that increasing the thickness of absorber layer results in higher efficiency. The concen- tration of shallow acceptors in the SnS has a crucial effect in the conversion efficiency, which rises up to about 15% for acceptor concentrations of 1019 cm􏰂3. The effect of the compensation ratio between donors and acceptors was also analysed but its effect on conversion efficiency is insignificant., This work was supported by European Commission through FP7-PEOPLE-2010-IRSES-NanoCIS project. One of the authors (H.U.) acknowledges the Erasmus Mundus Innovation and Design for Euro-Asian Scholars-Action 2 Programme of the European Commission for financial support.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Self-consistent relativistic band structure of the CH3NH3PbI3 perovskite

  • Menéndez-Proupin, E.
  • Palacios Clemente, Pablo
  • Wahnón Benarroch, Perla
  • Conesa Cegarra, José Carlos
The electronic structure and properties of the orthorhombic phase of the CH3NH3PbI3 perovskite are computed with density functional theory. The structure, optimized using a van der Waals functional, reproduces closely the unit cell volume. The experimental band gap is reproduced accurately by combining spin-orbit effects and a hybrid functional in which the fraction of exact exchange is tuned self-consistently to the optical dielectric constant. Including spin-orbit coupling strongly reduces the anisotropy of the effective mass tensor, predicting a low electron effective mass in all crystal directions. The computed binding energy of the unrelaxed exciton agrees with experimental data, and the values found imply a fast exciton dissociation at ambient temperature. Also polaron masses for the separated carriers are estimated. The values of all these parameters agree with recent indications that fast dynamics and large carrier diffusion lengths are key in the high photovoltaic efficiencies shown by these materials., This work was supported by the European Project NANOCIS of the FP7-PEOPLE-2010-IRSES and DEF-HYDFT (SOPHIA project)., Peer reviewed
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Electronic and atomic structure of complex defects in Al- and Ga-highly doped ZnO films

  • Menéndez Proupin, Eduardo
  • Palacios Clemente, Pablo|||0000-0001-7867-8880
  • Wahnón Benarroch, Perla|||0000-0002-5420-2906
Archivo Digital UPM
Publication Artículo científico (JournalArticle)

Electronic band alignment at CuGaS2 chalcopyrite interfaces

  • Palacios Clemente, Pablo|||0000-0001-7867-8880
  • Wahnón Benarroch, Perla|||0000-0002-5420-2906
  • Castellanos Aguila, J.e.
  • Conesa, J.c.
  • Arriaga, J.
Archivo Digital UPM
Publication Contribución de congreso (ConferenceOutput)

Propiedades estructurales y electrónicas de hetero-interfases de CuGaS2:Cr para su uso en células solares de alta eficiencia

  • Palacios Clemente, Pablo|||0000-0001-7867-8880
  • Wahnón Benarroch, Perla|||0000-0002-5420-2906
  • Castellanos Águila, Jesús Eduardo
  • Arriaga, J.
Archivo Digital UPM
Publication Contribución de congreso (ConferenceOutput)

Estructura electrónicas de perovskitas fotovoltaicas: el caso del CH3NH3PbI3

  • Menéndez Proupin, Eduardo
  • Palacios Clemente, Pablo|||0000-0001-7867-8880
  • Wahnón Benarroch, Perla|||0000-0002-5420-2906