Skip to main content

APROVECHAMIENTO DE LA LUZ SOLAR CON PROCESOS DE DOS FOTONES-TF

ENE2016-77798-C4-2-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2016
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 34
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrodeposited chromium-doped alpha-Fe2O3 under various applied potential configurations for solar water splitting

  • Bouhjar, Feriel
  • Derbali, Lotfi
  • Bessais, Brahim
  • Marí, B.|||0000-0003-0001-419X
[EN] In this work, high quality hematite (alpha-Fe2O3) Chromium (Cr)-doped thin films have been synthesized via electrodeposition technique, on fluorine-doped fin oxide-coated glass substrates, under various applied potential configurations [cyclic voltammetry (CV), linear sweep voltammetry (LSV) and - 0.5 V]. Chromium was added to the electrolyte at such a proportion that the Cr/(Cr + Fe) ratio remained within 8%. The as-deposited films were subsequently annealed in air at 650 degrees C for 2 h. Our novel study highlights the effect of using variable potential approaches during the film preparation on the properties of Cr-alpha-Fe2O3 deposited films. The prepared thin films were analyzed by X-ray diffraction, Raman spectroscopy, scanning electron microscopy, UV-Vis absorption and photoelectrochemical (PEC) analysis. XRD revealed that samples are crystallized in Cr-Fe2O3 cubic structure with a crystalline orientation in the plane (1 1 1) and a clear improvement of the crystallinity and size crystallite of the Cr-Fe2O3 deposited using CV process. SEM micrographs showed that the morphology grains were three-sided pyramid-shaped, expanding with increase of the crystallinity. The calculated band gap values are 2.18, 2.23 and 2.20 eV, respectively for - 0.5 V, LSV, CV. The Cr-Fe2O3 films synthesized in this study showed high PEC activity with very low carrier density in comparison with the conventionally electrodeposited films. This Cr-doped hematite films 'excellent photoelectrochemical performance was mainly attributed to improved charge carrier properties. Such high photoactivity was attributed to the large active surface area and increased donor density caused by increasing the Cr doping in the alpha-Fe2O3 films., This work was supported by the Ministry of High Education and Scientific Research (Tunisia), the Ministry of Economy and Competitiveness (Spain) (ENE2016-77798-C4-2-R) and the Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Hydrothermal synthesis of nanostructured Cr-doped hematite with enhanced photoelectrochemical activity

  • Bouhjar, Feriel
  • Chourou, M.L.
  • Bessais, Brahim
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] Using the easily applicable hydrothermal method Cr-doped hematite thin films have been deposited polycrystalline on conductive glass substrates. The hydrothermal bath consisted of an aqueous solution containing a mixture of FeCl3.6H(2)O and NaNO3 at pH = 1.5. The samples were introduced in an autoclave and heated for a fixed time at a fixed temperature and then annealed in air at 550 degrees C. The concentration of the incorporated Cr atoms (Cr4+ ions) was controlled by varying the concentration of the Cr(ClO4)(3) precursor solution, varied from 0% to 20%. All samples followed morphological and structural studies using field-emission scanning electron microscopy, high-resolution transmission electron microscopy and X-ray diffraction. Chronoamperometry measurements showed that Cr-doped hematite films exhibited higher photoelectrochemical activity than the undoped films. The maximum photocurrent density and incident photon conversion efficiencies (IPCE) were obtained for 16 at.% Cr-doped films. This high photoactivity can be attributed to both the large active surface area and increased donor density caused by Cr-doping in the alpha-Fe2O3 films. All samples reached their best IPCE at 400 nm. IPCE values for 16 at.% Cr-doped hematite films were thirty times higher than that of undoped samples. This high photoelectrochemical performance of Cr-doped hematite films is mainly attributed to an improvement in charge carrier properties. (C) 2017 Elsevier Ltd. All rights reserved., This work was supported by the Ministry of Higher Education and Scientific Research, Tunisia and Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

SnS Thin Films Prepared by Chemical Spray Pyrolysis at Different Substrate Temperatures for Photovoltaic Applications

  • Sall, Thierno
  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Sans-Tresserras, Juan Ángel|||0000-0001-9047-3992
[EN] The preparation and analysis of morphological, structural, optical, vibrational and compositional properties of tin monosulfide (SnS) thin films deposited on glass substrate by chemical spray pyrolysis is reported herein. The growth conditions were evaluated to reduce the presence of residual phases different to the SnS orthorhombic phase. X-ray diffraction spectra revealed the polycrystalline nature of the SnS films with orthorhombic structure and a preferential grain orientation along the (111) direction. At high substrate temperature (450A degrees C), a crystalline phase corresponding to the Sn2S3 phase was observed. Raman spectroscopy confirmed the dominance of the SnS phase and the presence of an additional Sn2S3 phase. Scanning electron microscopy (SEM) images reveal that the SnS film morphology depends on the substrate temperature. Between 250A degrees C and 350A degrees C, SnS films were shaped as rounded grains with some cracks between them, while at substrate temperatures above 400A degrees C, films were denser and more compact. Energy-dispersive x-ray spectroscopy (EDS) analysis showed that the stoichiometry of sprayed SnS films improved with the increase of substrate temperature and atomic force microscopy micrographs showed films well covered at 350A degrees C resulting in a rougher and bigger grain size. Optical and electrical measurements showed that the optical bandgap and the resistivity decreased when the substrate temperature increased, and smaller values, 1.46 eV and 60 Omega cm, respectively, were attained at 450A degrees C. These SnS thin films could be used as an absorber layer for the development of tandem solar cell devices due to their high absorbability in the visible region with optimum bandgap energy., This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of the effect of V-doping on the opto-electrical properties of spray-pyrolized SnS thin films

  • Urbaniak, A.
  • Pawlowski, M.
  • Marzantowicz, M.
  • Sall, Thierno
  • Marí, B.|||0000-0003-0001-419X
[EN] SnS is an earth-abundant material that is a potentially suitable candidate for the absorber layer in solar cells. Here spray-pyrolized SnS thin films doped with vanadium were studied using structural and opto-electrical methods. The thin films have an orthorhombic structure with a preferential (111) crystallographic direction. SnS has an indirect bandgap of around 1.05 eV, whereas doping with vanadium changes the band edge and shifts the absorption threshold to around 1.2 eV. The photoluminescence study revealed a broad peak related to the band-to-band transition of energy at around 1.2 eV and an additional sharp peak positioned at 1.17 eV related to vanadium. Additionally, a non-radiative recombination mechanism followed by hopping through band fluctuation barriers has been proposed for photoluminescence quenching at increased temperatures. The conductivity measurements reveal that conductivity weakly increases with V-doping, whereas its activation energy decreases from around 0.38 eV to 0.35 eV., This work was supported by the Minister den Economic y Competitividad (ENE2016-77798-C4-2-R) and Generalitat Valencia (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of Zinc Content in Ternary ZnCdS Films Deposited by Chemical Bath Deposition for Photovoltaic Applications

  • Ullah, Shafi
  • Ullah, Hanif
  • Bouhjar, F.
  • Chahboun, Adil
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] Cadmium Zinc Sulfide thin films with different Zn concentration were synthesized in aqueous solution by chemical bath deposition (CBD) method using CdSO4, ZnSO4, CH4N2S for Cd+2, Zn+2, and S¿2 ions source, respectively. The as-deposited films are well homogeneous, adherent and free from pinholes. The incorporation of Zn in CdS was found to be dependent on the annealing temperature. Structure, morphology, elemental analysis, optical and photoelectrochemical (PEC) properties of ZnCdS were characterized using X-ray diffraction, atomic force microscopy, energy dispersive spectroscopy, transmission electron microscopy and UV-Vis absorption measurements, respectively. According to EDS analysis the films are non-stoichiometric due to a deficit of sulfur, which becomes more important as the Zn content increases. The absorption edge shifts toward the lower wavelength region and hence the bandgap of the films increases as the Zn content increases. The values of optical absorption edge are found to change from 2.42 eV for CdS and 2.90 eV for ZnS thin films. The PEC and linear sweep voltammetry performance of the Zn doped CdS films were examined by chronoamperometry technique which provided a significant high potential current due to increase of the electrical conductivity as compared to CdS film., This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat Valenciana (Prometeus 2014/044). The Universitat Politecnica de Valencia, Coordinator of the Erasmus + KA 107 Scholarship funded by European Union under project (2016-17)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the power conversion efficiency of perovskite solar cells with different materials as Hole-Transport Layer by numerical simulations

  • Casas, Guillermo
  • Cappelletti, M.A.
  • Kazraz Mohammad, Moetaz
  • Peltzer y Blancá, E.L.
  • Marí, B.|||0000-0003-0001-419X
[EN] In this paper, a theoretical study of different p-p-n perovskite solar cells has been performed by means of computer simulation. Effects of the offset level upon the power conversion efficiency (PCE) of these devices have been researched using five different materials such as spiro-OMeTAD, Cu2O, CuSCN, NiO and CuI, as Hole Transporting Layer (HTL). The Solar Cells Capacitance Simulator (SCAPS)-1D has been the tool used for numerical simulation of these devices. A strong dependence of PCE has been found with the difference between the Maximum of the Valence Band of the HTL and perovskite materials, and with the doping level in p-type perovskite layer. A minimum value of hole mobility in the HTL has been also found, below which the PCE is reduced. Efficiencies in the order of 28% have been obtained for the Cu2O/Perovskite/TiO2 solar cell. Results obtained in this work show the potentiality of this promising technology., This work was partially supported by the Universidad Nacional de Quilmes, Argentina, by the Universidad Nacional Arturo Jauretche, Argentina, by the Universidad Nacional de La Plata, Argentina, by the National Council Research (CONICET), Argentina, and by the Ministerio de Economia y Competitividad (Grant ENE2016-77798-C4-2-R), Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Synthesis of in-gap band CuGaS2:Cr absorbers and numerical assessment of their performance in solar cells

  • Ullah, Shafi
  • Ullah, Hanif
  • Bouhjar, Feriel
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] CuGaS2 thin films were obtained by sulfurization of CuGaSe2. CuGaSe2 thin films were first electrodeposited from aqueous solutions containing CuCl2, GaCl3, and H2SeO3 and subsequently annealed at 400 °C for 10 min in forming gas atmosphere and in the presence of molecular sulfur. This sulfurization process resulted in the complete conversion of CuGaSe2 into CuGaS2. The formation of CuGaS2 was proven by X-Ray diffraction and optical spectroscopy. Diffraction peaks of CuGaS2 shifted to higher angles than those observed for CuGaSe2 films, and the optical band gap shifted to blue rising from 1.66 eV for CuGaSe2 to 2.2 eV for CuGaS2. When Cr ions were added to the initial electrolyte, the final CuGaS2 films exhibited a broad in-gap absorption band centred at 1.63 eV that can be ascribed to Cr atoms in Ga sites. The performance of solar cells based on CuGaS2:Cr absorbers containing an in-gap absorption band was then estimated by numerical simulation using Solar Cell Capacitance Simulator Software. Both quantum efficiency and short circuit current of simulated Mo/CuGaS2:Cr/CdS/ZnO solar cells rose up proportionally to the amount of Cr present in CuGaS2:Cr absorbers. As a result, the photo conversion efficiency of the simulated devices changed from 14.7% for CuGaS2 to 34% for CuGaS2:Cr absorbers. Nevertheless, when neutral defects related to Cr-doping were introduced in the absorber layer, the positive effect of the enhancement of photon harvesting due to IGB was compensated by a decline in the carrier collection and the overall efficiency of the device fell considerably., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Impact of iodide substitution on the physical properties and stability of cesium lead halide perovskite thin films CsPbBr3-xIx (0 &lt, = x &lt, = 1)

  • Atourki, Lahoucine
  • Vega-Fleitas, Erica
  • Kirou, Hassan
  • Bouabid, Khalid
  • Ihlal, Ahmed
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] This study sheds light on the effect of iodide substitution on the structural and optical properties of solution processed mixed cesium lead perovskite thin films CsPbBr3-xIx (0 <= x <= 1) as well as their atmospheric and thermal stability. Pawley fit indicated that the mixed lead halide CsPbBr(3-x)l(x) perovskite crystallizes in the orthorhombic (Pnma) space group. X-ray diffraction analyses showed a shift to lower angles when the average fraction of iodide incorporated increased indicating the expansion of the lattice. Absorbance measurements show that the CsPbBr3-xIx films exhibit a very high absorbance in the visible and short infrared region. The band gap of CsPbBr(3-x)l(x) is tuned from 238 (CsPbBr3) to 2.17 eV (CsPbBr2I1) following the Vegard's law. CsPbBr3 films showed a bright photoluminescence with emission maximum at 530 nm CsPbBr(3-x)l(x) films demonstrate excellent stability after aging for two days in a humid environment (relative humidity of 60%) and under thermal annealing at relatively high temperature. (C) 2017 Elsevier B.V. All rights reserved., This work was supported by Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical Modeling Baseline for high efficiency (Cu2FeSnS4) CFTS based Thin Film Kesterite Solar Cell

  • Khattak, Yousaf Hameed
  • Baig, Faisal
  • Ullah, Shafi
  • Ullah, Hanif
  • Marí, B.|||0000-0003-0001-419X
[EN] Cu2FeSnS4 (CFTS) is auspicious nontoxic and earth abundant semiconductor compound having kesterite symmetrical structure. It is an attractive and suitable material for the fabrication of low cost, high efficiency and sustainable thin film photovoltaic cell. ¿¿¿¿¿¿¿¿ based kesterite photovoltaic cell device modeling was performed in this work. The influence of device parameters such as the thickness, acceptor and donor carrier concentration densities of absorber and electron transport layer (ETL), effect of back contact metal work function and the temperature effect on the performance of ¿¿¿¿¿¿¿¿ based kesterite photovoltaic cell is analyzed by using one dimensional solar cell capacitance simulator (SCAPS) software. In this work, promising optimized results had been achieved with the conversion efficiency of 19.97%, fill factor (¿¿¿¿) 85.94 %, short-circuit current (¿¿¿¿¿¿ ) 23.37 ¿¿¿¿/¿¿¿ 2 and open circuit voltage (¿¿¿¿¿¿ ) 0.995V. The above results will give imperative baselines and feasible directions for the fabrication of higher efficiency ¿¿¿¿¿¿¿¿ based photovoltaic cell, This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tin-mono-sulfide (SnS) Thin Films Prepared by Chemical Spray Pyrolysis with Different [S]/[Sn] Ratios

  • Sall, Thierno
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] SnS thin films were deposited by chemical spray pyrolysis using cost-effective and low-toxicity sources materials like tin (II) chloride dihydrate and thiourea as sources of tin and sulphur, respectively. We have studied the properties of sprayed SnS thin films with [S]/[Sn] ratios were varied from 1 to 4 in order to optimize these parameters. X-ray diffraction was used for analyzing the films structure, Raman Spectroscopy for assessing the films quality and structure, scanning electron microscope (SEM) for surface morphology and energy dispersive energy (EDS) for compositional element in samples, atomic force microscopy (AFM) for the topography of surfaces and optical spectroscopy for measuring transmittances and then deducing the band gap energies. All films obtained are polycrystalline with (111) as preferential direction for films with [S]/[Sn] ratio equals to one while for [S]/[Sn] ratios from 2 to 4 the main peak becomes (101) and the (111) peak decreases in intensity. Raman spectroscopy confirms the presence of only one SnS phase without any additional parasite secondary phases. SEM images revealed that films are well adhered onto glass surface with rounded grain. AFM confirms this result being films with [S]/[Sn] = 1 the roughest and also with the largest grain size. EDS results show an improvement of stoichiometry with the increase of the [S]/[Sn] ratio. From optical analysis, it is inferred that the band gap energy decreases from 1.83 to 1.77 eV when the [S]/[Sn] ratio changes from 2 to 4., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Single Step Electrodeposited Kesterite Cu2ZnSnS4 (CZTS) thin films at low annealing temperatures

  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • El Nahrawy, Amany
  • Saber, Suzan
  • Khattab, Nagwa
  • Eid, Ali
  • Abo-Aly, Mohamed
  • Bouhjar, Feriel
[EN] This paper reports onthe growth of quaternary Cu2ZnSnS4 (CZTS) thin films by a single step electrochemicaldeposition followed by annealing at low temperature.The influence of different annealing atmospheres at constant annealingtimes (t = 45min) and fixed preparation controlling parameters; i.e., starting materials (precursor metal salts) solution concentration, time of deposition and electrodeposition potential. Structural, compositional, morphological, andoptical properties, as well as photoelectrochemical properties were studied. The films, sulfurized during 2 hours, showeda prominent kesterite phase with a nearly stoichiometric composition. Samples were characterizedby X-ray diffraction (XRD), scanning electron microscopy (SEM), EDS and UV-VIS-NIR spectrometry. X-ray diffraction and confirmed the formation of pure kesterite CZTS films. SEM shows that films are compact with densemorphology and homogeneous distribution. EDS analyzed the elemental constituents of the quaternary Cu2ZnSnS4 with an apparent Cu deficiency and S rich for the sulfurized samples. From optical study, the energy gap was indexed for the sulfurized samples,Eg=1.52 eV. Under illumination sulfurized CZTS films exhibits negative photocurrent and positive photovoltagevalues confirming the p-type character of the films., This work was supported by the Culture, Affairs and Missions Sector, Ministry of Higher Education and Scientific Research (Egypt) and Ministerio de Economia y Competitividad (Spain) (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Enhanced luminescence by tunable coupling of Eu3+ and Tb3+ in ZnAl2O4:Eu3+:Tb3+ phosphor synthesized by solution combustion method

  • Verma, Naveen
  • Singh, Krishan Chander
  • Jindal, Jitender
  • Yadav, Suprabha
  • Mittal, Anuj
  • Marí, B.|||0000-0003-0001-419X
[EN] ZnAl2O4:Eu3+ or Tb3+ (1 mol%) and ZnAl2O4:Eu3+/Tb3+ with varied concentrations of Eu3+ and Tb3+ were prepared by solution combustion method. The photoluminescence spectra of synthesized compounds shows that simultaneous doping of Tb3+ and Eu3+ causes enhancement in Eu3+ luminescence intensity. This indicates some energy transfer from Tb3+ to Eu3+. This phenomenon of Tb3+ -> Eu3+ energy transfer, accomplishing enhanced intensity of Eu3+ ions, is attributed to the cross relaxation phenomenon, which is favored by overlap between the donor and acceptor transition. The energy is transferred to Eu3+ cascade rapidly via non-radiative transitions to D-5(0) state. The synthesized compounds were characterized by XRD, SEM for their structural and morphological characteristics respectively., This work was supported by the European Commission through NanoCIS project (FP7-PEOPLE-2010-IRSES ref. 269279).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of guanidinium on the optical properties and structure of the methylammonium lead halide perovskite

  • Vega-Fleitas, Erica
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] The stability and performance of perovskite-based solar cells can be improved by changing the nature of the organic cation. Herein, mixed methylammoniumeguanidinium perovskites (MA1-xGAxPbI3) are structurally and optically characterized. The Pawley fit method confirmed the formation of the iodide halide GAPbI3 tetragonal phase (P42_NMC). Up to 20% of the guanidinium cation was incorporated in the methylammonium lead iodide perovskite, producing a lattice enlargement, which was investigated studying the shift of the diffraction peaks of the MAPbI3 (I4_CM) tetragonal lattice. Long-term stability was tested, resulting in improved mixed perovskites with a low GA content. The bandgap shifted to lower energies. The absorption bandgap diminished slightly when the GA cation substituted up to 20% of MA in MAPbI3, degrading when the GA amount in the mixed perovskite is larger. FESEM morphological analysis was performed showing that a uniform thin film was deposited. PL studies showed that only shallow defects had been introduced., This work was supported by Ministerio de Economia y Competitividad [ENE2016-77798-C4-2-R] and Generalitat Valenciana [Prometeus 2014/044].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Modelling of novel-structured copper barium tin sulphide thin film solar cells

  • Hameed, K. Yousaf
  • Baig, Faisal
  • Toura, Hanae
  • Beg, Saira
  • Khani, Naveed Ali Kaim
  • Marí, B.|||0000-0003-0001-419X
[EN] In this work, a novel structured Cu2BaSnS4 (CBTS)/ZnS/Zn(O, S) photovoltaic device is proposed. A nontoxic, earth-abundant and auspicious quaternary semiconductor compound copper barium tin sulphide (Cu2BaSnS4) is used as an absorber layer. We propose a novel Zn(O, S) buffer layer for a high-power conversion efficiency (PCE) of CBTS-based thin film photovoltaic cells. Solar cell capacitance simulator software is used for device modelling and simulations are performed under a 1.5 AM illumination spectrum. The proposed device is investigated by means of numerical modelling and optimized the parameters to maximize its efficiency. Promising optimized functional parameters had been achieved from the proposed structure with back surface field layer with a PCE of 18.18%, a fill factor of 83.45%, a short-circuit current of 16.13 mA cm¿2 and an open-circuit voltage of 1.3 V. The promising results give an imperative standard for possible manufacturing of high efficiency, eco-friendly inorganic CBTS-based photovoltaic cells., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of Cu2O Back Surface Field on the Efficiency Enhancement of CZTSe Kesterite Photovoltaic Cell

  • Khattak, Yousaf Hameed
  • Baig, Faisal
  • Marí, B.|||0000-0003-0001-419X
[EN] The earth abundant materiel Cu2ZnSnSe4 (CZTSe) is a promising quaternary semiconductor compound having kesterite symmetrical structure. CZTSe is considered as suitable absorber material for photovoltaic cell applications due to its optimum direct band gap. Cu2O/CZTSe/CdS/ZnO photovoltaic solar cell is proposed in this paper. Numerical modeling and analysis of the proposed cell is performed by using Solar Cell Capacitance Simulator (SCAPS). To analyze the effects on the cell performance different physical parameters are varied such as the thickness of the buffer and absorber layers and their carrier densities. Under 1.5 AM illumination condition, the proposed cell shows promising results and had achieved power conversion efficiency (PCE) of 25.95%, fill factor (FF) 85.24%, short circuit current (J(sc)) 31.41 mA/cm(2) and (V-oc) 0.97 V., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Study of the reverse saturation current and series resistance of p-p-n perovskite solar cells using the single and double-diode models

  • Cappelletti, M.A.
  • Casas, G.A.
  • C!edola, A.P.
  • Peltzer y Blanc!a, E.L
  • Marí, B.|||0000-0003-0001-419X
[EN] The effects of the offset level and of the doping level in the perovskite layer upon both the reverse saturation current (J0) and the series resistance (Rs) of p-p-n perovskite solar cells have been researched in this paper, using five different materials such as spiro-OMeTAD, Cu2O, CuSCN, NiO and CuI, as Hole Transporting Material (HTM). The analysis was carried out by means of the single and double-diode models of a solar cell and of genetic algorithms based on optimization technique, in order to extract the desired parameters. The minor degradation of J0 and Rs has been found for the condition offset equal to zero and for the highest doping level in p-type perovskite layer. Also, a comparison has been made of the behavior of two reverse saturation currents (J01 and J02). The power conversion efficiency (PCE) has shown to be more strongly dependent on J02 than on J01. Results obtained in this work can be used to improve the manufacturing process of these devices., This work was partially supported by the National Council Research (CONICET), Argentina, by the Universidad Nacional Arturo Jauretche, Argentina, by the Universidad Nacional de Quilmes, Argentina, by the Universidad Nacional de La Plata, Argentina and by the Ministerio de Economía y Competitividad (Grant ENE2016-77798-C4-2-R), Spain
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of P+ - ZnTe back surface contact on photovoltaic performance of ZnTe based solar cells

  • Bayad, Hamza
  • Elmanouni, Ahmed
  • Khattak, Yousaf Hameed
  • Ullah, Shafi
  • Baig, Faisal
  • Marí, B.|||0000-0003-0001-419X
[EN] In order to improve photovoltaic performance of solar cells based on ZnTe thin films two device structures have been proposed and its photovoltaic parameters have been numerically simulated using Solar Cell Capacitance Simulator software. The first one is the ZnO/CdS/ZnTe conventional structure and the second one is the ZnO/CdS/ZnTe/P+-ZnTe structure with a P+-ZnTe layer inserted at the back surface of ZnTe active layer to produce a back surface field effect which could reduce back carrier recombination and thus increase the photovoltaic conversion efficiency of cells. The effect of ZnO, CdS and ZnTe layer thicknesses and the P+-ZnTe added layer and its thickness have been optimized for producing maximum working parameters such as: open-circuit voltage Voc, short-circuit current density Jsc, fill factor FF, photovoltaic conversion efficiency ¿. The solar cell with ZnTe/P+-ZnTe junction showed remarkably higher conversion efficiency over the conventional solar cell based on ZnTe layer and the conversion efficiency of the ZnO/CdS/ZnTe/P+-ZnTe solar cell was found to be dependent on ZnTe and P+-ZnTe layer thicknesses. The optimization of ZnTe, CdS and ZnTe layers and the inserting of P+-ZnTe back surface layer results in an enhancement of the energy conversion efficiency since its maximum has increased from 10% for ZnO, CdS and ZnTe layer thicknesses of 0.05, 0.08 and 2 µm, respectively to 13.37% when ZnO, CdS, ZnTe and P+-ZnTe layer thicknesses are closed to 0.03, 0.03, 0.5 and 0.1 µm, respectively. Furthermore, the highest calculated output parameters have been Jsc = 9.35 mA/cm2, Voc = 1.81 V, ¿=13.37% and FF= 79.05% achieved with ZnO, CdS, ZnTe, and P+-ZnTe layer thicknesses about 0.03, 0.03, 0.5 and 0.1 µm, respectively. Finally, the spectral response in the long-wavelength region for ZnO/CdS/ZnTe solar cells has decreased at the increase of back surface recombination velocity. However, it has exhibited a red shift and showed no dependence of back surface recombination velocity for ZnO/CdS/ZnTe/P+-ZnTe solar cells., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Synthesis and characterization of perovskite FAPbBr(3-x) I (x) thin films for solar cells

  • Slimi, B.
  • Ben Assaker, I.
  • Kriaa, A.
  • Chtourou, R.
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] FAPbI3, FAPbBr3, and FAPbBr3-xIx perovskite thin films were produced in a single step from a solution containing a mixture of FAI, PbI2, FABr, and PbBr2 (FA = formamidinium). FAPbBr3-xIx perovskite thin films were deposited onto ITO-coated glass substrates by spin coating. X-ray diffraction analyses confirmed that these thin-film perovskites crystallize in the cubic phase (Pm-3 m) for all composition range 0 B x B 3. Mixed lead perovskites showed a high absorbance in the UV¿Vis range. The optical band gap was estimated from spectral absorbance measurements. It was found that the onset of the absorption edge for FAPbBr3¿xIx thin films ranges between 1.47 and 2.20 eV for x = 0 and x = 3, respectively. Photoluminescence emission energies for mixed halide perovskites were also dependent on their composition and presented intermediate values from 810.4 nm for FAPbI3 to 547.3 nm for FAPbBr3., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical analysis a guide to improve the efficiency of experimentally designed solar cell

  • Baig, Faisal
  • Khattak, Yousaf Hameed
  • Ullah, Shafi
  • Ullah, Hanif
  • Marí, B.|||0000-0003-0001-419X
[EN] In this paper a numerical modelling guide is proposed about how to improve the efficiency of experimentally designed solar cells with the aid of numerical analysis. To validate the study presented in this paper, we first reproduce the results for experimentally designed solar cell in SCAPS with solar cell structure p-SnS/n-CdS having a conversion efficiency of 1.5%. After this device performance was optimized in solar cell capacitance simulator (SCAPS) by changing absorber layer thickness, buffer layer thickness, minority carrier lifetime, absorber acceptor doping concentration, buffer donor doping concentration and adding window layer. After optimization of physical device parameters and structure the new solar cell structure p-SnS/n-CdS/n-ZnO achieves power conversion efficiency (PCE) of 14.01% in SCAPS., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical analysis of a novel CNT/Cu2O/Sb2Se /In2S3/ITO antimony selenide solar cell

  • Baig, Faisal
  • Khattak, Yousaf Hameed
  • Beg, Saira
  • Marí, B.|||0000-0003-0001-419X
[EN] Sb2Se3 antimony selenide is a great potential for solar cell commercial application with good absorption coefficient and optimal band gap. In recent years the maximum power conversion efficiency (PCE) achieved from Sb2Se3 is about 6.5% with CNT/PbS/Sb2Se3/CdS/ITO structure. In this structure PbS works as hole transport material (HTM), CdS as buffer layer and Au as back contact. But the toxic nature of (Cd, Pb) and high cost of Au contact it cannot be considered for commercial application. Because of this reason for the first-time alternate solar cell structure with Cu2O as HTM layer, In2S3 as buffer layer and carbon nano tube (CNT) electrode used as a back contact is proposed in this work for Sb2Se3. Device modeling for solar cell with structure CNT/Cu2O/Sb2Se3/In2S3/ITO was performed in solar cell capacitance simulator (SCAPS). After optimization of physical parameters like absorber thickness, acceptor doping of absorber layer, donor doping of buffer and replacing CdS buffer layer with In2S3 efficiency of experimentally designed cell jumped from 6.5% to 13.20%., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2R) and Generalitat valenciana (Prometeus2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Enhancement of the conversion efficiency of thin film kesterite solar cell

  • Khattak, Yousaf Hameed
  • Baig, Faisal
  • Ullah, Shafi
  • Ullah, Hanif
  • Marí, B.|||0000-0003-0001-419X
[EN] Cu2ZnSnS4(CZTS) is a non-toxic earth abundant material and a promising quaternary semiconductor compound of groups I - II - IV - VI having a kesterite symmetrical structure. Due to its optimum direct bandgap, it has been considered as a suitable material for absorber layers for photovoltaic cell applications. This paper presents the numerical simulation and modeling of CZTS based thin film kesterite photovoltaic cells using SCAP-1D software. The influence of device parameters such as the carrier concentration, thickness, densities of absorber, buffer and window layers, defect densities and the temperature effect on the performance of the ZnO/CdS/CZTS/Mo photovoltaic cell structure are analyzed. Defect densities are added to the absorber layer and the interface between the buffer layer and the absorber layer. This type of solar cell does not comprise any toxic material and can lead to non-toxic thin film photovoltaic cells with outstanding optical properties. In this work, promising optimized results had been achieved with a conversion efficiency of 23.72%, a fill factor of 82.54%, a short-circuit current (J(sc)) of 44.87 mA/cm(2), and an open circuit voltage (V-oc) of 0.64V. Published by AIP Publishing., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Efficiency Enhancement of Cu2BaSnS4 Experimental Thin film Solar Cell by Device Modeling

  • Khattak, Yousaf Hameed
  • Baig, Faisal
  • Toura, Hanae
  • Beg, Saira
  • Marí, B.|||0000-0003-0001-419X
[EN] Copper barium tin sulfide (CBTS) is a direct band gap earth abundant, non-toxic and quaternary semiconductor compound. It is used as absorber because of its direct band gap of 1.9 eV. A numerical guide is proposed for CBTS-based photovoltaic cell to enhance the efficiency of experimentally designed device with introducing Cu2O as back surface field (BSF) layer by means of numerical modeling. Device optimization was performed in SCAPS-1D software under 1.5 AM illumination spectrum. After introducing BSF layer and optimized physical parameters, promising result was achieved with PCE of 9.72%, V-oc of 0.81 V, J(sc) of 15.73 mA/cm(2) and FF of 78.23%. The promising outcomes of this work will give a guideline for the feasible production of high-efficiency inorganic CBTS-based photovoltaic cells., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrochemical Fabrication and Characterization of p-CuSCN/n-Fe2O3 Heterojunction Devices for Hydrogen Production

  • Bouhjar, Feriel
  • Ullah, Shafi
  • Bessais, Brahim
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] p-CuSCN/n-Fe2O3 heterojunctions were electrochemically prepared by sequentially depositing alpha-Fe2O3 and CuSCN films on FTO (SnO2:F) substrates. Both alpha-Fe2O3 and CuSCN films and alpha-Fe2O3/CuSCN heterojunctions were characterized by field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD). Pure crystalline CuSCN films were electrochemically deposited on alpha-Fe2O3 films by fixing the SCN/Cu molar ratio in an electrolytic bath to 1:1.5 at 60 degrees C, and at a potential of -0.4 V. The photocurrent measurements showed increased intrinsic surface states or defects at the alpha-Fe2O3/CuSCN interface. The photoelectrochemical performance of the alpha-Fe2O3/CuSCN heterojunction was examined by chronoamperometry and linear sweep voltammetry techniques. The alpha-Fe2O3/CuSCN structure exhibited greater photoelectrochemical activity compared to the alpha-Fe2O3 thin films. The highest photocurrent density was obtained for the alpha-Fe2O3/CuSCN films in 1 M NaOH electrolyte. This strong photoactivity was attributed to both the large active surface area and the external applied bias, which favored the transfer and separation of the photogenerated charge carriers in the alpha-Fe2O3/CuSCN heterojunction devices. The flatband potential and donor density were maximal for the heterojunction. These results suggest a substantial potential to achieve heterojunction thin films in photoelectrochemical water splitting applications. (c) 2017 The Electrochemical Society. All rights reserved., This work was supported by the Ministry of High Education and Scientific Research (Tunisia), Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Optoelectronic characterization of CuInGa(S)2 thin films grown by spray pyrolysis for photovoltaic application

  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
  • Hartiti, Bouchaib
  • Ullah, Shafi
  • Ullah, Hanif
  • Ebn Touhami, Mohamed
  • Santos, D. M. F.
[EN] Copper-indium gallium disulfide (CIGS) is a good absorber for photovoltaic application. Thin films of CIGS were prepared by spray pyrolysis on glass substrates in the ambient atmosphere. The films were characterized by different techniques, such as structural, morphological, optical and electrical properties of CIGS films were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), spectrophotometer and Hall effect, respectively. After optimization, the deposited films structure, grain size, and crystallinity became more important with an increase of annealing time at 370 degrees C for 20 min. Transmission electron microscopy (TEM) analysis shows that the interface sheets are well crystallized and the inter planer distance are 0.25 nm, 0.28 nm, and 0.36 nm. The atomic force microscopy (AFM) observation shows that the grain size and roughness can be tolerated by optimizing the annealing time. The strong absorbance and low transmittance were observed for the prepared films with a suitable energy bandgap about 1.46 eV. The Hall effect measurement system examined that CIGS films exhibited optimal electrical properties, resistivity, carrier mobility, and carrier concentration which were determined to be 4.22 x 10(6) omega cm, 6.18 x 10(2) cm(2) V-1 S-1 and 4.22 x 10(6) cm(-3), respectively. The optoelectronic properties of CIGS material recommended being used for the photovoltaic application., Prof. Bouchaib HARTITI, The Senior Associate at ICTP, is very grateful to ICTP for permanent support. Prof. Mohamed Ebn Touhami, Director of the University Center for Analysis, Expertise, Transfer of Technology and Incubation, Kenitra, Morocco, is very grateful to CUA2TI for financial support. Thanks to Doctor Diogo M.F. Santos for the supervision of Amal Bouich's work during her research in CeFEMA research center. The authors also thank researchers from CeFEMA (IST-ULisboa, Portugal) and CUA2TI (FS-Kenitra Morocco) for their help.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Structural and Electrochemical Analysis of CIGS: Cr Crystalline Nanopowders and Thin Films Deposited onto ITO Substrates

  • Saber, Suzan
  • Andrio, Andreu
  • Escorihuela, Jorge
  • Khattab, Nagwa
  • Eid, Ali
  • El Nahrawy, Amany
  • Abo Ali, Mohamed
  • Marí, B.|||0000-0003-0001-419X
  • Compañ Moreno, Vicente|||0000-0001-8233-7472
[EN] A new approach for the synthesis of nanopowders and thin films of CuInGaSe2(CIGS)chalcopyrite material doped with different amounts of Cr is presented. The chalcopyrite mate rial CuInxGa1 ¿ xSe2 was doped using Cr to form a new doped chalcopyrite with the structure CuInxCryGa1 ¿ x ¿ ySe2, where x = 0.4 and y = 0.0, 0.1, 0.2, or 0.3. The electrical properties of CuInxCryGa1 ¿ x ¿ ySe2 are highly dependent on the Cr content and results show these materials as promis ing dopants for the fabrication thin film solar cells. The CIGS nano-precursor powder was initially synthesized via an autoclave method, and then converted into thin films over transparent sub strates. Both crystalline precursor powders and thin films deposited onto ITO substrates following a spin-coating process were subsequently characterized using XRD, SEM, HR-TEM, UV¿visible and electrochemical impedance spectroscopy (EIS). EIS measurement was performed to evaluate the dc-conductivity of these novel materials as conductive films to be applied in solar cells., This research has been supported by the Culture Affairs and Missions Sector, Ministry of Higher Education and Scientific Research (Egypt) and Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R), (ENE2015-69203-R) and Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Annealing study of electrodeposited CuInSe2 and CuInS2 thin films

  • Saber, Suzan
  • El Nahrawy, Amany
  • Khattab, Nagwa
  • Eid, Ali
  • Abo Ali, Mohamed
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] In this study CuInSe2 and CuInS2 thin films were prepared onto ITO glass substrate using the electrodeposition technique in aqueous solution. The electrodeposited films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDS). The annealing effects on electrodeposited precursors were investigated. The chalcopyrite structure of CuInSe2/CuInS2 showed an enhancement of crystallinity after subsequent selenization/sulfurization treatment in Se/S atmosphere, respectively. XRD and SEM studies revealed a dramatic improvement of the crystalline quality of CIS films after annealing treatments. Mott-Schottky measurements were used to assess the conductivity type of the films and their carrier concentration. The prepared samples underwent an etching process to remove the binary accumulated Cu2-x(Se,S) phases shown in FESEM pictures. This etching process has shown a noticeable decrease in both, the flat band potencial, Vfb (V), and the number of acceptors, NA (cm-3) in selenized CuInSe2 and sulfurized CuInS2 samples., This work was supported by the Culture Affairs and Missions Sector, Ministry of Higher Education and Scientific Research (Egypt) and Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Opto-electrical characterisation of In-doped SnS thin films for photovoltaic applications

  • Urbaniak, A.
  • Pawlowski, M.
  • Marzantowicz, M.
  • Sall, Thierno
  • Marí, B.|||0000-0003-0001-419X
[EN] Spray pyrolised SnS thin films doped with indium were studied using various optical and electrical techniques.Structural analysis shows that all films crystallise in an orthorhombic structurewith (111) as a preferential direction, without secondary phases. The doping of SnS layers with indium results in better morphology with increased grain size. Absorption measurements indicate a dominant direct transition with energy decreasing from around 1.7 eV to 1.5 eV with increased indium supply. Apart from the direct transition, an indirect one, of energy of around 1.05 eV, independent of indiumdoping, was identified. The photoluminescence study revealed two donors to acceptor transitions between two deep defect levels and one shallower one, with an energy of around 90 meV. The observed transitions did not depend significantly on In concentration. The conductivitymeasurements reveal thermal activation of conductivity with energy decreasing from around 165 meV to 145 meV with increased In content., This work was supported by the Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrodeposited Cr-Doped alpha-Fe2O3 thin films active for photoelectrochemical water splitting

  • Bouhjar, Feriel
  • Derbali, Lotfi
  • Bessais, Brahim
  • Marí, B.|||0000-0003-0001-419X
[EN] Polycrystalline hematite (alpha-Fe2O3) Chromium (Cr)-doped thin films were electrodeposited on fluorine-doped tin oxide-coated glass substrates. The electrodeposition bath comprised an aqueous solution containing FeCl3 center dot 6H(2)O, NaCl, and H2O2.Chromium was added to the electrolyte at such a proportion that the Cr/(Cr + Fe) ratio remained within the 2-8 at. % range. The as-deposited films were subsequently annealed in air at 650 degrees C for 2 h. The structure and morphological characteristics of the undoped and Cr-doped alpha-Fe2O3 thin films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV-Vis spectroscopy. Cr doping led the main XRD lines to shift to lower angles, which mostly resulted from substituting Fe3+ for Cr4+ ions that leads to alpha-Fe2O3 lattice contraction. The SEM observations showed that the roughness and aspect of surfaces changed with the Cr doping level. The photoelectrochemical (PEC) performance of the alpha-Fe2O3 films was examined by chronoamperometry and linear sweep voltammetry techniques. The Cr-doped films exhibited greater photoelectrochemical activity than the undoped alpha-Fe2O3 thin films. The highest photocurrent density was obtained for the 8% Cr-doped alpha-Fe2O3 films in 1 M NaOH electrolyte. All the samples achieved their best IPCE at 400 nm. The IPCE values for the 8 at.% Cr-doped hematite films were 20-fold higher than that of the undoped sample.This Cr-doped hematite films 'excellent photoelectrochemical performance was mainly attributed to improved charge carrier properties. Such high photoactivity was attributed to the large active surface area and increased donor density caused by increasing the Cr doping in the alpha-Fe2O3 films. (C) 2019 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved., This work was supported by the Ministry of High Education and Scientific Research (Tunisia), the Ministry of Economy and Competitiveness (Spain) (ENE2016-77798-C4-2-R) and the Generalitat Valenciana (Prometeus 2014/044).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Single step electrochemical deposition for the fabrication of CZTS kesterite thin films for solar cells

  • Khattak, Yousaf Hameed
  • Baig, Faisal
  • Toura, Hanae
  • Harabi, Imen
  • Beg, Saira
  • Marí, B.|||0000-0003-0001-419X
[EN] The high absorption coefficient and direct optical band gap of a kesterite Cu2ZnSnS4 (CZTS) makes it very promising absorber material in the manufacturing of high efficiency and low-cost thin film photovoltaic cells. Single step electrochemical deposition of CZTS quaternary compound thin films on Indium tin oxide (ITO) substrates is reported in this work. The films were obtained from aqueous solutions at room temperature. The key objective of this work is to examine the effect of annealing temperature on CZTS thin films. Sulfurization of thin films was performed under different temperature range from 400 degrees C to 550 degrees C. Good crystal structure was achieved at temperature 500 degrees C with the complexing agent of trisodium citrate. Deposited films material composition was evaluated by analyzing UV-visible spectroscopy, EDS, FE-SEM and XRD. The thin film with good morphological, structural and optical (1.51 eV) properties was achieved at temperature 500 degrees C. The results reported in this work will provide an imperative guideline for efficient low-cost design of CZTS thin films., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R) and Generalitat Valenciana (Prometeus 2014/044)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Synthesis and characterization of coupled ZnO/SnO2 photocatalysts and their activity towards degradation of cibacron red dye

  • Verma, Naveen
  • Yadav, Suprabha
  • Mittal, Anuj
  • Jindal, Jitender
  • Marí, B.|||0000-0003-0001-419X
[EN] A series of coupled ZnO-SnO2 photocatalyst was successfully synthesized in the Zn:Sn molar ratio of 20:1, 10:1, 5:1 and 2:1 via co-precipitation method followed by calcination at different temperatures. The synthesized materials were characterized by X-ray diffraction, diffuse reflectance spectra, scanning electron microscope and transmission electron microscope. Photocatalytic activitiy of synthesized materials was applied for the degradation of cibacron red dye in aqueous solution under UV-A light irradiation. Experimental results revealed that the coupled ZnO-SnO2 photocatalyst with Zn:Sn molar ratio 10:1, calcined at 600 degrees C for 1 h was the most efficient photocatalyst among synthesized samples for the degradation of cibacron red. Superoxide anion radical (O-center dot(2)-) was found to be the prominent active species responsible for degradation comparative to hole (h(+)), hydroxyl radical ((OH)-O-center dot)., Naveen Verma thanks the M. D. University, Rohtak, India for providing final assistance under Radha Krishanan foundation fund (DSW/16/322) and Suprabha Yadav thanks University Grant Commission, New Delhi, India for the award of Junior Research Fellowship.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tetrabutylammonium-Doped Methylammonium lead iodide: high quality and stable perovskite thin films

  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
  • Marí-Guaita, Julia
  • Sahraoui, Bouchta
  • Palacios, Pablo
[EN] This work reported the successive incorporation of tetrabutylammonium (TBA) into Methylammonium lead Iodide (MAPbI3) perovskite. The thin films were characterized by X-Ray diffraction (XRD), Scanning electron microscopy (SEM), Transmittance electron microscopy (TEM), Atomic force microscopy (AFM), and UV-Visible spectroscopy. It was shown that introducing TBA increases the crystallinity, grain size, surface morphology without pin-hole, and roughness of the MAPbI3 thin films. Moreover, the MA(1-X)TBAX PbI3 thin film shows better stability in a relative humidity of ~60% after 15 days than the pure MAPbI3 thin film. The obtained results are hoped to be helpful for stability and improvement of the performance of the MAPbI3 thin films by doping TBA cations under ambient conditions., This work was supported by the Ministerio de Economia y Competitividad (ENE 2016-77798-C4-2-R). Author AB acknowledged the Post-doctoral contract supported by the RRHH, the Postdoctoral contract the Margarita Salas financed with union European Next Generation EU. Grant PID2019-107137RB-C21 and PID2019-107137RB-C22OAQ funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Comparative study of binary cadmium sulfide (CdS) and tin disulfide (SnS2) thin buffer layers

  • Ullah, Shafi
  • Bouich, Amal|||0000-0001-6745-8831
  • Marí, B.|||0000-0003-0001-419X
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Ullah, Hanif
[EN] Binary compound tin disulfide (SnS2) and cadmium sulfide (CdS) are the potential candidates used as a buffer layer for copper indium gallium selenide (CIGS) and copper zinc tin sulfide (CZTS) thin-film device. Herein, both compounds have been successfully prepared through simple hydrothermal (HD) and chemical bath deposition (CBD) techniques, respectively. The prepared samples were characterized by different available techniques like X-ray diffraction (XRD), atomic force microscopy (AFM), surface electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmittance electrons microscopy (TEM), UV¿Visible spectroscopy and photoelectrochemical (PEC) analysis. The XRD analysis confirms the polycrystalline nature of the prepared thin films. AFM analysis showed that the SnS2 display better roughness (60 nm), grain size (75 nm) than CdS roughness (23 nm), grain size (41 nm) thin films. SEM and EDS studies revealed near stoichiometry behavior of elemental composition of the films. The optical absorption spectrum showed the direct bandgap of CdS 2.45 eV and 2.20 eV for SnS2 thin films. The PEC analysis revealed that the SnS2 thin films exhibit two times higher photoresponse (140 µA) as compare to CdS (80 µA) thin films. The SnS2 high photocurrent could be attributed to the small band gap and increase in grain size which can trap more incident light. Based on the results the SnS2 used as a buffer layer can be a good choice for an efficient photovoltaic device., This work was supported by the ministry of education generalitat Valenciana under grant no (ENE2016-77798-C4-2-R)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of Fe Content in Binary SnS2 Synthesis by Hydrothermal Technique for Photovoltaic Application

  • Ullah, Shafi
  • Ullah, Hanif
  • Vega-Fleitas, Erica
  • Baig, Faisal
  • Hameed, Yousaf
  • Bouich, Amal|||0000-0001-6745-8831
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] Binary thin disulfide (SnS2) and ternary Sn1-x FexS2 (X = Fe (2.5%, 5% and 10%) which has huge potentials in the visible-light rang due to its bandgap 2.2-2.6 eV. Herein, SnS2 and Sn1-x FexS2 powders have been synthesize by a fruitful hydrothermal method. The structure, morphology, elemental composition and optical properties of the obtained product were characterized by using X-ray diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), Electron Dispersive Spectroscopy (EDS) and UV-Vis spectroscopy. It was found that the Fe could be effectively incorporated in the obtained Sn(1-x)FexS(2) compounds. According to XRD analysis, increased concentration of Fe in the Sn1-xFexS2 compounds results in a gradual degradation of the crystallinity. The optical bandgap was found to be 1.52 eV, 2.22 eV, 2.38 eV and 2.48 eV, for the SnS, SnS2, Fe 5% and Fe 10% respectively. Mott-Schottky measurements performed for SnS2 confirm the n-type character of SnS2 samples. (c) 2019 The Electrochemical Society., This work was supported by Ministerio de Economia y Competitividad (ENE2016-77798-C4-2-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of a Compact Fe2O3 Layer on the Photovoltaic Performance of Perovskite-Based Solar Cells

  • Bouhjar, F.
  • Ullah, Shafi
  • Bessais, B.
  • Mollar García, Miguel Alfonso|||0000-0003-4315-0407
  • Marí, B.|||0000-0003-0001-419X
[EN] In this study, uniform and dense iron oxide ¿-Fe2O3 thin films were used as an electron-transport layer (ETL) in CH3NH3PbI3-based perovskite solar cells (PSCs), replacing the Titanium dioxide (TiO2) ETL conventionally used in planar heterojunction perovskite solar cells. The ¿-Fe2O3 films were synthesized using an electrodeposition method for the blocking layer and a hydrothermal method for the overlaying layer, while 2,2¿,7,7¿-tetrakis (N, N¿-di-p-methoxyphenylamine)-9,9¿ spirobifluorene (spiro-OMeTAD) was employed as a hole conductor in the solar cells. Based on the above synthesized ¿-Fe2O3 films the photovoltaic performance of the PSCs was studied. The ¿-Fe2O3 layers were found to have a significant impact on the photovoltaic conversion efficiency (PCE) of the PSCs. This was attributed to an efficient charge separation and transport due to a better coverage of the perovskite on the ¿-Fe2O3 films. As a result, the PCE measured under standard solar conditions (AM 1.5G, 100 mW cm¿2) reached 5.7%., This work was supported by the Ministry of High Education and Scientific Research, Tunisia and Ministerio de Economia y Competitividad (ENE2013-46624-C4-4-R) and Generalitatvalenciana (Prometeus 2014/044).