Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Electrical characteristics of silicon nanowire transistors fabricated by scanning probe and electron beam lithographies

  • Kyoung Ryu, Yu
  • Chiesa, Marco
  • García García, Ricardo
Silicon nanowire (SiNW) field-effect transistors have been fabricated by oxidation scanning probes and electron beam lithographies. The analysis and comparison of the electron mobility and subthreshold swing shows that the device performance is not affected by the top-down fabrication method. The two methods produce silicon nanowire transistors with similar electrical features, although oxidation scanning probe lithography generates nanowires with smaller channel widths. The values of the electron mobility and the subthreshold swing, 200 cm2 V−1 s−1 and 500 mV dec−1, respectively, are similar to those obtained from bottom-up methods. The compatibility of top-down methods with CMOS (complementary metal–oxide–semiconductor) procedures, the good electrical properties of the nanowire devices and the potential for making sub-10 nanowires, in particular by using oxidation scanning probe lithography, make those methods attractive for device fabrication., This work was funded by the Spanish Ministry of Science (MICINN) through MAT2009-08650 and the Comunidad de Madrid S2009/MAT-1467 and the European Commission FP7/2007-2013 under grant agreement No. 318804. MC acknowledges the program ‘Juan de la Cierva’ (MICINN)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Fabrication of sub-12 nm thick silicon nanowires by processing scanning probe lithography masks

  • Kyoung Ryu, Yu
  • Postigo, Pablo Aitor
  • García-Pérez, Fernando
  • García García, Ricardo
Silicon nanowires are key elements to fabricate very sensitive mechanical and electronic devices. We provide a method to fabricate sub-12 nm silicon nanowires in thickness by combining oxidation scanning probe lithography and anisotropic dry etching. Extremely thin oxide masks (0.3-1.1 nm) are transferred into nanowires of 2-12 nm in thickness. The width ratio between the mask and the silicon nanowire is close to one which implies that the nanowire width is controlled by the feature size of the nanolithography. This method enables the fabrication of very small single silicon nanowires with cross-sections below 100 nm2. Those values are the smallest obtained with a top-down lithography method. © 2014 AIP Publishing LLC., This work was funded by the European Union FP7/2007-2013 under Grant Agreement No. 318804 (SNM)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Tuning piezoresistive transduction in nanomechanical resonators by geometrical asymmetries

  • Llobet, Jordi
  • Sansa Perna, Marc
  • Lorenzoni, Matteo
  • Borrisé, Xavier
  • San Paulo, Álvaro
  • Perez Murano, Francesc X.
Under the terms of the Creative Commons Attribution (CC BY) license to their work., The effect of geometrical asymmetries on the piezoresistive transduction in suspended double clamped beam nanomechanical resonators is investigated. Tapered silicon nano-beams, fabricated using a fast and flexible prototyping method, are employed to determine how the asymmetry affects the transduced piezoresistive signal for different mechanical resonant modes. This effect is attributed to the modulation of the strain in pre-strained double clamped beams, and it is confirmed by means of finite element simulations., The research leading to these results received funding from the European Union's Seventh Framework Programme FP7/2007-2013, under Grant Agreement No. 318804 (SNM). Support is also acknowledged from project Force for future (CSD2010-00024)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Fabrication of functional electromechanical nanowire resonators by focused ion beam implantation

  • Llobet, Jordi
  • Gerbolés, Marta
  • Sansa Perna, Marc
  • Borrisé, Xavier
  • Perez Murano, Francesc X.
A fast and flexible fabrication method that allows the creation of silicon structures of various geometries is presented. It is based on the combination of focused ion beam local gallium implantation, selective silicon etching, and diffusive boron doping. The structures obtained by this resistless method are electrically conductive. Freely suspended mechanical resonators of different dimensions and geometries have been fabricated and measured. The resulting devices present a good electrical conductivity which allows the characterization of their high-frequency mechanical response by electrical read-out., This work is supported by the European Seventh Framework Programme (FP7) within the project SNM: single nanometer manufacturing for beyond CMOS devices and by national funding from FORCE-for-FUTURE (CSD2010-00024) and SGR-NANONEMS (2014 SGR 1025). J. Ll. is enrolled in the UAB’s PhD program in material science., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Sub-10 nm resistless nanolithography for directed self-assembly of block copolymers

  • Fernández-Regúlez, Marta
  • Evangelio, Laura
  • Lorenzoni, Matteo
  • Fraxedas, J.
  • Perez Murano, Francesc X.
The creation of highly efficient guiding patterns for the directed self-Assembly of block copolymers by resistless nanolithography using atomic force microscopy (AFM) is demonstrated. It is shown that chemical patterns consisting of arrays of lines defined on a brush layer by AFM allow the alignment of the blocks of lamella-forming polymers. The main advantage of this method relies on the capability to create high-resolution (sub-10 nm line-width) guiding patterns and the reduction of the number of process steps compared to the state-of-the-Art methods for creating guiding patterns by chemical surface modification. It is found that the guiding patterns induce the block alignment very efficiently, allowing the achievement of a density multiplication factor of 7 for block copolymers of 14 nm half-pitch, which is attributed to the combined effect of topographical and chemical modification., This work was partially funded by the projects SNM (FP7-ICT-2011-8), FORCE-for-FUTURE (CSD2010-0024), SiNSoc (MAT2011-15159-E) and NaNeau (MAT2012-38319-C02-01)., Peer reviewed, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Subsurface imaging of silicon nanowire circuits and iron oxide nanoparticles with sub-10 nm spatial resolution

  • Perrino, Alma P.
  • Ryu, Y. K.
  • Amo, Carlos A.
  • Morales, María Del Puerto
  • García García, Ricardo
Non-destructive subsurface characterization of nanoscale structures and devices is of significant interest in nanolithography and nanomanufacturing. In those areas, the accurate location of the buried structures and their nanomechanical properties are relevant for optimization of the nanofabrication process and the functionality of the system. Here we demonstrate the capabilities of bimodal and trimodal force microscopy for imaging silicon nanowire devices buried under an ultrathin polymer film. We resolve the morphology and periodicities of silicon nanowire pairs. We report a spatial resolution in the sub-10 nm range for nanostructures buried under a 70 nm thick polymer film. By using numerical simulations we explain the role of the excited modes in the subsurface imaging process. Independent of the bimodal or trimodal atomic force microscopy approach, the fundamental mode is the most suitable for tracking the topography while the higher modes modulate the interaction of the tip with the buried nanostructures and provide subsurface contrast., This work was funded by the European Union FP7/2007-2013 under Grant Agreement No. 318804 (SNM), the Ministerio de Economía y Competitividad (Spain) under grants MAT2013-44858-R, CSD2010-00024 and the European Research Council ERC-AdG-340177 (3DNanoMech)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Direct fabrication of thin layer MoS2 field-effect nanoscale transistors by oxidation scanning probe lithography

  • Espinosa, Francisco M.
  • Ryu, Y. K.
  • Marinov, Kolyo
  • Dumcenco, Dumitru
  • Kis, Andras
  • García García, Ricardo
Thin layer MoS2-based field effect transistors (FET) are emerging candidates to fabricate very fast and sensitive devices. Here, we demonstrate a method to fabricate very narrow transistor channel widths on a single layer MoS2 flake connected to gold electrodes. Oxidation scanning probe lithography is applied to pattern insulating barriers on the flake. The process narrows the electron path to about 200 nm. The output and transfer characteristics of the fabricated FET show a behavior that is consistent with the minimum channel width of the device. The method relies on the direct and local chemical modification of MoS2. The straightforward character and the lack of specific requirements envisage the controlled patterning of sub-100 nm electron channels in MoS2 FETs., This work was funded by the European Union FP7/2007-2013 under Grant Agreement No. 318804 (SNM), the Ministerio de Economía y Competitividad (Spain) under Grant No. MAT2013-44858-R, the Marie Curie ITN network “MoWSeS” (Grant No. 317451) and the Swiss SNF Sinergia Grant No. 147607., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Sub-20 nm patterning of thin layer WSe2 by scanning probe lithography

  • Dago, Arancha I.
  • Ryu, Y. K.
  • García García, Ricardo
The electronic properties of thin layer transition metal dichalcogenides have raised considerable interest in the fabrication of advanced field-effect transistors and ultrasensitive sensors. Downscaling those devices to the nanoscale depends on the development of cost-effective and robust alternative nanolithographies. Here we demonstrate the direct, resist-less and reproducible nanopatterning of tungsten diselenide thin layers. By using oxidation scanning probe lithography (o-SPL) we have generated arrays of dots with a width of 13 nm and periodicity of 40 nm. We have also patterned a point contact of 35 nm and a nanoscale field-effect transistor. The direct and resistless fabrication of WSe2 nanoscale devices by oxidation scanning probe lithography opens a straightforward and reliable method for processing transition metal dichalcogenides materials., This work was funded by the European Union FP7/2007-2013 under Grant Agreement No. 318804 (SNM) and the Ministerio de Economía y Competitividad (Spain) under Grant No. MAT2013-44858-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Advanced oxidation scanning probe lithography

  • Ryu, Y. K.
  • García García, Ricardo
Force microscopy enables a variety of approaches to manipulate and/or modify surfaces. Few of those methods have evolved into advanced probe-based lithographies. Oxidation scanning probe lithography (o-SPL) is the only lithography that enables the direct and resist-less nanoscale patterning of a large variety of materials, from metals to semiconductors; from self-assembled monolayers to biomolecules. Oxidation SPL has also been applied to develop sophisticated electronic and nanomechanical devices such as quantum dots, quantum point contacts, nanowire transistors or mechanical resonators. Here, we review the principles, instrumentation aspects and some device applications of o-SPL. Our focus is to provide a balanced view of the method that introduces the key steps in its evolution, provides some detailed explanations on its fundamentals and presents current trends and applications. To illustrate the capabilities and potential of o-SPL as an alternative lithography we have favored the most recent and updated contributions in nanopatterning and device fabrication., This work was funded by the European Union FP7/2007-2013 under Grant Agreement No. 318804 (SNM) and the Ministerio de Economía y Competitividad (Spain) under grants MAT2013-44858-R, MAT2015-69725-REDT and MAT2016-76507-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Chemical and structural analysis of sub-20 nm graphene patterns generated by scanning probe lithography

  • Dago, Arancha I.
  • Sangiao, S.
  • Fernández-Pacheco, Rodrigo
  • Teresa, José María de
  • García García, Ricardo
Sub-20 nm patterns have been fabricated by using oxidation scanning probe lithography on epitaxial graphene. The structural and chemical properties of these nanopatterns have been characterized by high resolution transmission electron microscopy, energy dispersive X-ray spectroscopy and electron energy loss spectroscopy. The electron microscopy images reveal that the nanolithography process modifies the graphene monolayer and a thin region of the SiC substrate (1 nm thick). Spatially-resolved electron spectroscopies show that the nanopatterns are made of graphene oxide. The combination of spatially-resolved structural and chemical analysis of graphene nanopatterns will enable the development of high-performance graphene devices., Financial support by several projects are acknowledged: MAT2014-51982-C2-1-R, MAT2014-51982-C2-2-R and MAT2015-69725-REDT, MAT2016-76507-R from MINECO (including FEDER funding) and Aragón Regional Government. This work was also funded by the European Union FP7/2007-2013 under Grant Agreement No. 318804 (SNM)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Sub-20 nm patterning of thin layer WSe2 by scanning probe lithography

  • Dago, Arancha I.
  • Ryu, Y. K.
  • García García, Ricardo
Trabajo presentado en la conferencia Fuerzas y Túnel (FyT2016), celebrada en Girona del 5 al 7 de septiembre de 2016., Transition metal dichalcogenides (TMDs) have been broadly studied as promising materials for the development of advanced electronic, optoelectronic and sensing devices. Their electronic properties together with their mechanical flexibility and their optical transparency have caught the attention of the scientific community in recent years [1]. However, some restrictions need to be overcome so that these materials become viable materials for the fabrication of semiconductor devices [2]. For instance, reliable lithographic techniques are needed with which to control the width of the devices in the nanometric scale. Oxidation scanning probe lithography (o-SPL) has been applied for the nanopatterning of molibdenum disulfide (MoS2) [3]. Here we report the sub-30 nm patterning of tungsten diselenide (WSe2) thin layers by o-SPL (Fig.1a) and its application to the fabrication of a WSe2 nanoscale field-effect transistor (FET). The electronic properties of the device were not degraded during the patterning procedure (Fig. 1b). The fabricated WSe2 nano-transistor has been used as a nanoscale humidity sensor [4]., We acknowledge support from the European Union under Grant Agreement No. 318804 (SNM)., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Advanced scanning probe lithography

  • García García, Ricardo
  • Knoll, Armin W.
  • Riedo, Elisa
The nanoscale control afforded by scanning probe microscopes has prompted the development of a wide variety of scanning-probe-based patterning methods. Some of these methods have demonstrated a high degree of robustness and patterning capabilities that are unmatched by other lithographic techniques. However, the limited throughput of scanning probe lithography has prevented its exploitation in technological applications. Here, we review the fundamentals of scanning probe lithography and its use in materials science and nanotechnology. We focus on robust methods, such as those based on thermal effects, chemical reactions and voltage-induced processes, that demonstrate a potential for applications., Financial support from the European Research Council AdG no. 340177 (R.G.) and StG no. 307079 (A.W.K.), the European Commission FP7-ICT-2011 no. 318804 (R.G. and A.W.K.), the Swiss National Science Foundation SNSF no. 200020-144464 (A.W.K.), the Ministerio de Economía y Competitividad MAT2013-44858-R (R.G.), the National Science Foundation CMMI-1100290 (E.R.), the MRSEC program DMR-0820382 (E.R.) and the Office of Basic Energy Sciences of the Department of Energy DE-SC0002245 (E.R.) are acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Identifying the nature of surface chemical modification for directed self-assembly of block copolymers

  • Evangelio, Laura
  • Gramazio, Federico
  • Lorenzoni, Matteo
  • Gorgoi, Michaela
  • Espinosa, Francisco M.
  • García García, Ricardo
  • Perez Murano, Francesc X.
  • Fraxedas, J.
In recent years, block copolymer lithography has emerged as a viable alternative technology for advanced lithography. In chemicalepitaxy- directed self-assembly, the interfacial energy between the substrate and each block copolymer domain plays a key role on the final ordering. Here, we focus on the experimental characterization of the chemical interactions that occur at the interface built between different chemical guiding patterns and the domains of the block copolymers. We have chosen hard X-ray high kinetic energy photoelectron spectroscopy as an exploration technique because it provides information on the electronic structure of buried interfaces. The outcome of the characterization sheds light onto key aspects of directed self-assembly: grafted brush layer, chemical pattern creation and brush/block co-polymer interface., The research leading to these results has received funding from the European Community's Seventh Framework Programme (FP7/2007-2013) within the projects CoLiSA (FP7-ICT-2013-11) and SNM (FP7-ICT-2011-8) and from MINECO (Nanointegra, TEC2015-69864-R). Financial support under the CALIPSO Programme (HZBPHOTONS_CALIPSO-96) is highly appreciated. ICN2 acknowledges support from the Severo Ochoa Program (MINECO, Grant SEV-2013-0295) and from the CERCA Programme (Generalitat de Catalunya). Ricardo García acknowledges financial support from MAT2013-4458-R. Laura Evangelio acknowledges the Ministry of Education of Spain for her FPU grant (FPU 13/03746).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Thermal scanning probe lithography for the directed self-assembly of block copolymers

  • Gottlieb, S
  • Lorenzoni, M
  • Evangelio, Laura
  • Fernández-Regúlez, Marta
  • Ryu, Y K
  • Rawlings, C
  • Spieser, M
  • Knoll, A W
  • Perez Murano, Francesc X.
Thermal scanning probe lithography (t-SPL) is applied to the fabrication of chemical guiding patterns for directed self-assembly (DSA) of block copolymers (BCP). The two key steps of the overall process are the accurate patterning of a poly(phthalaldehyde) resist layer of only 3.5 nm thickness, and the subsequent oxygen-plasma functionalization of an underlying neutral poly(styrene-random-methyl methacrylate) brush layer. We demonstrate that this method allows one to obtain aligned line/space patterns of poly(styrene-block-methyl methacrylate) BCP of 18.5 and 11.7 nm half-pitch. Defect-free alignment has been demonstrated over areas of tens of square micrometres. The main advantages of t-SPL are the absence of proximity effects, which enables the realization of patterns with 10 nm resolution, and its compatibility with standard DSA methods. In the brush activation step by oxygen-plasma exposure, we observe swelling of the brush. This effect is discussed in terms of the chemical reactions occurring in the exposed areas. Our results show that t-SPL can be a suitable method for research activities in the field of DSA, in particular for low-pitch, high-χ BCP to achieve sub-10 nm line/space patterns., This project is partially funded by the EU projects SNM (grant agreement no. 318804) and NFFA (grant agreement no. 654360), and by the Spanish NANOINTEGRA (TEC2015-69864-R). We would like to acknowledge Chris-tophe Navarro and Celia Nicolet from Arkema for supplying some of the polymers used in this work. We would also like to thank Charlotte Bolliger for proofreading the manuscript., Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Chemical and structural analysis of sub-20 nm graphene patterns generated by scanning probe lithography

  • Dago, A.I.
  • Sangiao, S.
  • Fernández-Pacheco, R.
  • De Teresa, J.M.
  • Garcia, R.
Sub-20 nm patterns have been fabricated by using oxidation scanning probe lithography on epitaxial graphene. The structural and chemical properties of these nanopatterns have been characterized by high resolution transmission electron microscopy, energy dispersive X-ray spectroscopy and electron energy loss spectroscopy. The electron microscopy images reveal that the nanolithography process modifies the graphene monolayer and a thin region of the SiC substrate (1 nm thick). Spatially-resolved electron spectroscopies show that the nanopatterns are made of graphene oxide. The combination of spatially-resolved structural and chemical analysis of graphene nanopatterns will enable the development of high-performance graphene devices.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Identifying the nature of surface chemical modification for directed self-assembly of block copolymers

  • Evangelio Araujo, Laura
  • Gramazio, Federico
  • Lorenzoni, Matteo|||0000-0001-5287-8761
  • Gorgoi, Michaela
  • Espinosa, Francisco Miguel
  • García, Ricardo
  • Pérez-Murano, Francesc
  • Fraxedas, Jordi|||0000-0002-2821-4831
In recent years, block copolymer lithography has emerged as a viable alternative technology for advanced lithography. In chemical-epitaxy-directed self-assembly, the interfacial energy between the substrate and each block copolymer domain plays a key role on the final ordering. Here, we focus on the experimental characterization of the chemical interactions that occur at the interface built between different chemical guiding patterns and the domains of the block copolymers. We have chosen hard X-ray high kinetic energy photoelectron spectroscopy as an exploration technique because it provides information on the electronic structure of buried interfaces. The outcome of the characterization sheds light onto key aspects of directed self-assembly: grafted brush layer, chemical pattern creation and brush/block co-polymer interface.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Resonant tunnelling features in a suspended silicon nanowire single-hole transistor

  • Llobet Sixto, Jordi|||0000-0001-7007-9277
  • Krali, Emiljana
  • Wang, Chen
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Jones, Mervyn E.
  • Pérez Murano, Francesc|||0000-0002-4647-8558
  • Durrani, Zahid A. K.
Suspended silicon nanowires have significant potential for a broad spectrum of device applications. A suspended p-type Si nanowire incorporating Si nanocrystal quantum dots has been used to form a single-hole transistor. Transistor fabrication uses a novel and rapid process, based on focused gallium ion beam exposure and anisotropic wet etching, generating <10 nm nanocrystals inside suspended Si nanowires. Electrical characteristics at 10 K show Coulomb diamonds with charging energy ∼27 meV, associated with a single dominant nanocrystal. Resonant tunnelling features with energy spacing ∼10 meV are observed, parallel to both diamond edges. These may be associated either with excited states or hole-acoustic phonon interactions, in the nanocrystal. In the latter case, the energy spacing corresponds well with reported Raman spectroscopy results and phonon spectra calculations.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Evaluating the compressive stress generated during fabrication of Si doubly clamped nanobeams with AFM

  • Lorenzoni, Matteo|||0000-0001-5287-8761
  • Llobet Sixto, Jordi|||0000-0001-7007-9277
  • Gramazio, Federico
  • Sansa Perna, Marc
  • Fraxedas, Jordi|||0000-0002-2821-4831
  • Pérez Murano, Francesc|||0000-0002-4647-8558
In this work, the authors employed Peak Force tapping and force spectroscopy to evaluate the stress generated during the fabrication of doubly clamped, suspended silicon nanobeams with rectangular section. The silicon beams, released at the last step of fabrication, present a curved shape that suggests a bistable buckling behavior, typical for structures that retain a residual compressive stress. Both residual stress and Young's modulus were extracted from experimental data using two different methodologies: analysis of beam deflection profiles and tip-induced mechanical bending. The results from the two methods are compared, providing an insight into the possible limitations of both methods.