Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 3
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Edge-Contact MoS2 Transistors Fabricated Using Thermal Scanning Probe Lithography

  • Conde Rubio, Ana
  • Liu, Xia
  • Boero, Giovanni
  • Brugger, Jürgen
The science and engineering of two-dimensional materials (2DMs), in particular, of 2D semiconductors, is advancing at a thriving pace. It is well known that these delicate few-atoms thick materials can be damaged during the processing toward their integration into final devices. Thermal scanning probe lithography (t-SPL) is a gentle alternative to the typically used electron beam lithography to fabricate these devices avoiding the use of electrons, which are well known to deteriorate the 2DMs' properties. Here, t-SPL is used for the fabrication of MoS2-based field effect transistors (FETs). In particular, the use of t-SPL is demonstrated for the first time for the fabrication of edge-contact MoS2 FETs, combining the hot-tip patterning and Ar+ milling to etch the 2DM. To avoid contamination of the contact interface by atmospheric gas molecules, etching and metal deposition are performed without breaking the vacuum conditions in between. With this process, edge-contact MoS2 FETs are successfully fabricated and characterized. On/off ratios up to 108 and 109 are obtained at room temperature in air and vacuum, respectively, i.e., comparable with the best values reported in the literature., The authors thank the Center of Micro/Nanotechnology (CMi) of EPFL. We also thank Sadegh Kamaei, Teodor Rosca, and Prof. A. M. Ionescu for their help with the electrical measurement set-up and access to their instruments. This work received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 Research and Innovation Program (Project “MEMS 4.0”, ERC-2016-ADG, grant agreement no. 742685)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Combining thermal scanning probe lithography and dry etching for grayscale nanopattern amplification

  • Erbas, Berke
  • Conde Rubio, Ana
  • Liu, Xia
  • Pernollet, Joffrey
  • Wang, Zhenyu
  • Bertsch, Arnaud
  • Penedo, Marcos
  • Fantner, Georg
  • Banerjee, Mitali
  • Kis, Andras
  • Boero, Giovanni
  • Brugger, Juergen
Grayscale structured surfaces with nanometer-scale features are used in a growing number of applications in optics and fluidics. Thermal scanning probe lithography achieves a lateral resolution below 10 nm and a vertical resolution below 1 nm, but its maximum depth in polymers is limited. Here, we present an innovative combination of nanowriting in thermal resist and plasma dry etching with substrate cooling, which achieves up to 10-fold amplification of polymer nanopatterns into SiO2 without proportionally increasing surface roughness. Sinusoidal nanopatterns in SiO2 with 400 nm pitch and 150 nm depth are fabricated free of shape distortion after dry etching. To exemplify the possible applications of the proposed method, grayscale dielectric nanostructures are used for scalable manufacturing through nanoimprint lithography and for strain nanoengineering of 2D materials. Such a method for aspect ratio amplification and smooth grayscale nanopatterning has the potential to find application in the fabrication of photonic and nanoelectronic devices., The authors thank the Center of Micro/Nanotechnology (CMi) of EPFL for fabrication facilities and the Interdisciplinary Centre for Electron Microscopy (CIME) of EPFL for FIB and SEM facilities. We also thank Damien Bertrand, Leonardo Cele, Guillaume Pellerin, Fabienne Bobard, Dr. Lucie Navratilova, Dr. Cyrille Hibert and Prof. Francesc Perez-Murano for their support with fabrication processes and metrology. This work received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation program (Project MEMS4.0, ERC-2016-ADG, grant agreement No. 742685) and the EU’s H2020 framework program for research and innovation under grant agreement n. 101007417, NFFA-Europe Pilot Project. M.B. acknowledges the support of SNSF Eccellenza grant No. PCEGP2_194528, and support from the QuantERA II Programme that has received funding from the European Union’s Horizon 2020 research and innovation program under Grant Agreement No 101017733. G.F. and M.P. received funding through the European research council H2020 - UE Framework Programme for Research & Innovation (2014-2020); ERC-2017-CoG; InCell; Project number 773091, and the Swiss National Science Foundation through grant 200021_182562., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Deterministic grayscale nanotopography to engineer mobilities in strained MoS2 FETs

  • Liu, Xia
  • Erbas, Berke
  • Conde Rubio, Ana
  • Rivano, Norma
  • Wang, Zhenyu
  • Jiang, Jin
  • Bienz, Siiri
  • Kumar, Naresh
  • Sohier, Thibault
  • Penedo, Marcos
  • Banerjee, Mitali
  • Fantner, Georg
  • Zenobi, Renato
  • Marzari, Nicola
  • Kis, Andras
  • Boero, Giovanni
  • Brugger, Juergen
Field-effect transistors (FETs) based on two-dimensional materials (2DMs) with atomically thin channels have emerged as a promising platform for beyond-silicon electronics. However, low carrier mobility in 2DM transistors driven by phonon scattering remains a critical challenge. To address this issue, we propose the controlled introduction of localized tensile strain as an effective means to inhibit electron-phonon scattering in 2DM. Strain is achieved by conformally adhering the 2DM via van der Waals forces to a dielectric layer previously nanoengineered with a gray-tone topography. Our results show that monolayer MoS2 FETs under tensile strain achieve an 8-fold increase in on-state current, reaching mobilities of 185 cm²/Vs at room temperature, in good agreement with theoretical calculations. The present work on nanotopographic grayscale surface engineering and the use of high-quality dielectric materials has the potential to find application in the nanofabrication of photonic and nanoelectronic devices., The authors thank the Center of Micro/Nanotechnology (CMi) of EPFL for the AFM facility support. X.L., B.E., A.C., G.B., and J.B. acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation program (Project “MEMS 4.0”, ERC-2016-ADG, grant agreement No. 742685), NFFA-Europe Pilot Project (the EU’s H2020 framework program for research and innovation, grant agreement No. 101007417). X.L. acknowledges fundings from the National Natural Science Foundation of China (No. 62274013) and the National Key Research and Development Program of China (No. 2023YFB3405600). M.B. acknowledges the support of SNSF Eccellenza grant No. PCEGP2_194528, and support from the QuantERA II Programme that has received funding from the European Union’s Horizon 2020 research and innovation program under Grant Agreement No 101017733. R.Z. acknowledges funding from the Swiss National Science Foundation through the NCCR MARVEL (project number 200021-143636) and the R’Equip program (grant number 206021-205312), as well as computational support from the Swiss National Supercomputing Centre. N.R. and N.M. acknowledge funding from the Swiss National Science Foundation (SNSF) and its National Centre of Competence in Research MARVEL on ‘Computational Design and Discovery of Novel Materials’ (grant number 182892). They also acknowledge computational support from the Swiss National Supercomputing Centre CSCS under project ID mr24. Z.W. and A.K. acknowledge financing from European Union’s Horizon 2020 research and innovation program under grant agreements 881603 (Graphene Flagship Core 3) and No 964735 (EXTREME-IR). G.F. and M.P. received funding through Innosuisse (AFM with PORT: Atomic force microscope with photothermal off-resonance tapping, grant number 7879, ext ref. 36938.1 IP-EE), FNS (Video-rate nanomechanical properties mapping using atomic force microscopy, grant number 7288, ext. ref. 200021_182562), H2020 (InCell - High speed AFM imaging of molecular processes inside living cellsInCell - High speed AFM imaging of molecular processes inside living cells, grant number 6823, ext ref. 773091, ETH Domain (An ecosystem for community driven scanning probe microscopy research and development, grant number 10126) and Eurostars (Correlated Analysis System for in-vivo Inspection of Semi-Conductor Process Wafers, grant number 9953, ext. ref. E!665 CAS-C)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed