Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 23
Encontrada(s) 1 página(s)

Docta Complutense
Publication Artículo científico (JournalArticle)

Realization of complex‐shaped magnetic nanotubes with 3D printing and electrodeposition

  • Fernández González, Claudia
  • Morales Fernández, Pamela
  • Turnbull, Luke Alexander
  • Abert, Claas
  • Suess, Dieter
  • Foerster, Michael
  • Niño, Miguel Á.
  • Nita, Pawel
  • Mandziak, Anna
  • Finizio, Simone
  • Bagués, Nuria
  • Pereiro, Eva
  • Fernández Pacheco, Amalio
  • Pérez García, Lucas
  • Ruiz Gómez, Sandra
  • Donnelly, Claire
The expansion of nanomagnetism to the third dimension leads to phenomena such as curvature-induced magnetochirality and anisotropy, which can significantly influence the behavior of magnetic textures. One of the most promising systems is the magnetic nanotube – where intrinsic curvature effects are present. However, studies of magnetic nanotubes remain limited to straight systems, and little is known about the influence of 3D geometries. In this work, three dimensional (3D) complex-shaped nanotubes are fabricated by combining nanoprinting with the conformal deposition of magnetic films. Specifically, 3D conductive non-magnetic tungsten scaffolds are fabricated using focused electron beam induced deposition and subsequently coated with a nickel magnetic shell, resulting in complex-shaped magnetic nanotubes whose geometry can be controlled by tuning the electron-beam parameters and electrodeposition conditions. Performing X-ray microscopy revealed that nanotubes of various geometries host a vortex-like azimuthal state, and that the energy landscape of the magnetic configuration can be tailored geometrically. Specifically, the pinning of magnetic domain walls at curved vertices is observed experimentally and confirmed with micromagnetic simulations, offering geometrical control of magnetic configurations in nanotube architectures. This approach provides a new pathway to fabricate and study complex 3D core-shell magnetic structures, facilitating experimental investigations of their fundamental properties, key for the next-generation of spintronic devices.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Microstructure of VO2 Thin Films Synthesized by Pulsed Laser Deposition

  • Romanitan, Cosmin|||0000-0002-5615-6624
  • Caicedo Roque, Jose Manuel|||0000-0002-5192-4989
  • Pascu, Razvan|||0000-0003-3170-9752
  • Mihalache, Iuliana|||0000-0002-4417-4972
  • Gavrila, Raluca|||0000-0002-0156-6036
  • Stoian, Marius|||0000-0002-6637-6671
  • Djourelov, Nikolay|||0000-0001-6531-8085
  • Padilla-Pantoja, Jessica|||0000-0002-7769-7753
In this paper, pulsed laser deposition (PLD) at low partial oxygen pressure (∼ 10 mTorr) was used to obtain VO thin films. During the PLD, the deposition temperature and number of pulses were varied in order to obtain a good sample crystallinity. It was showed by atomic force microscopy (AFM) micrographs that the mean grain size increased from ∼ 40 nm to ∼ 90 nm at a variation of the deposition temperature from 400 C to 500 C. Further, by increasing of both substrate temperature and number of pulses, the mean grain size increases to 220 nm. According to the Rietveld refinement of the experimental X-ray diffraction (XRD) pattern, within the grain size increasing, the mean crystallite size increased from 14 nm to 22 nm, as well as a decreasing of the lattice strain from 0.29% to 0.20%. These dependencies further imply a decreasing of the dislocation density of 2.3 to 0.9 × 10 cm. At the same time, the optical band gap decreased from 0.72 eV (400 C) to 0.66 eV (500 C), reaching 0.60 eV (600 C). Further investigations performed by X-ray photoelectron spectroscopy (XPS) showed the vanadium oxide presence, by the spin-orbit splitting of approximately 7.5 eV between V 2p and V 2p orbitals. Finally, the electrical measurements done in the range of 250 - 370 K reveal a close relationship between the dislocation density and the observed resistance-temperature dependence.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Development of hard X-ray photoelectron spectroscopy in liquid cells using optimized microfabricated silicon nitride membranes

  • Capone, F.|||0000-0002-7354-6317
  • Muntada, O.|||0000-0001-8508-2356
  • Ramírez, J. C.
  • Esplandiu Egido, Maria José|||0000-0003-2079-0639
  • Dedryvère, R.|||0000-0001-5125-640X
  • Grimaud, A.
  • Lassalle-Kaiser, B.|||0000-0003-2141-2496
  • Céolin, D.
  • Pérez Murano, Francesc|||0000-0002-4647-8558
  • Rueff, J.-P.|||0000-0003-3594-918X
  • Fraxedas, Jordi|||0000-0002-2821-4831
We present first hard X-ray photoelectron spectroscopy (HAXPES) results of aqueous salt solutions and dispersions of gold nanoparticles in liquid cells equipped with specially designed microfabricated thin silicon nitride membranes, with thickness in the 15-25 nm range, mounted in a high-vacuum-compatible environment. The experiments have been performed at the HAXPES endstation of the GALAXIES beamline at the SOLEIL synchrotron radiation facility. The low-stress membranes are fabricated from 100 mm silicon wafers using standard lithography techniques. Platinum alignment marks are added to the chips hosting the membranes to facilitate the positioning of the X-ray beam on the membrane by detecting the corresponding photoemission lines. Two types of liquid cells have been used, a static one built on an Omicron-type sample holder with the liquid confined in the cell container, and a circulating liquid cell, in which the liquid can flow in order to mitigate the effects due to beam damage. We demonstrate that the membranes are mechanically robust and able to withstand 1 bar pressure difference between the liquid inside the cell and vacuum, and the intense synchrotron radiation beam during data acquisition. This opens up new opportunities for spectroscopic studies of liquids.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Tin Oxide Nanoparticles via Solar Vapor Deposition for Hexavalent Chromium Remediation

  • Simeonidis, Konstantinos
  • Kalaitzidou, Kyriaki
  • Asimakidou, Theopoula
  • Martínez Boubeta, Carlos
  • Makridis, Antonios
  • Haeussler, Anita
  • Vourlias, Georgios
  • Balcells, Lluis
Tin oxide nanoparticles optimized to capture low concentrations of hexavalent chromium from water were developed through a facile, scalable, and low-cost one-step solar vapor deposition methodology. Considering the preservation of high electron donation capacity as the key to support the reduction of mobile Cr(VI) into insoluble forms, the growth of SnO nanoparticles was favored by the co-evaporation of SnO2 with Fe powders at various mass ratios. Characterization techniques indicated that the percentage and the stability of SnO is proportional to the Fe content in the target with a requirement of at least 50% wt to inhibit the formation of a passive SnO2 surface layer. The produced particles were evaluated regarding their efficiency to capture Cr(VI) under conditions similar to water treatment for drinking purposes (pH 7). It was revealed that passivation-free SnO nanoparticles deliver significant improvement in the adsorption capacity corresponding to the residual concentration of 25 μg/L, reaching a value of 1.74 mg/g for the sample prepared with 50% wt Fe in the target. The increase of water acidity was found responsible for the activation of more reduction sites on the particle surface, as reflected through the elevation of efficiency by more than 20% at pH 6., The research project was supported by the Hellenic Foundation for Research and Innovation (H.F.R.I.) under the “second Call for H.F.R.I. Research Projects to support Post-Doctoral Researchers” (Project Number: 00046 MagnoSorb). We thank the CNRS-PROMES laboratory, UPR 8521, belonging to the French National Centre for Scientific Research (CNRS), for providing access to its installations, the support of its scientific and technical staff, and the financial support of the SFERA-III project (Grant Agreement no. 823802). This work was supported by the French “Investments for the future” program managed by the National Agency for Research, under contact ANR-10-EQPX-49-SOCRATE (Equipex SOCRATE). This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement no. 101007417 and has benefited from the access provided by CSIC-ICMAB in Barcelona within the framework of the NFFA-Europe Pilot Transnational Access Activity, proposal ID262. C. M. Boubeta thanks the Spanish MCIN/AEI/10.13039/501100011033 programme for the financial support provided through a Torres Quevedo (PTQ2021-012178) fellowship. Ll. Balcells acknowledges the Ministry of Science and Innovation of Spain for the support through the OXISHOT project (PID2021-128410OB-I00)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Evaluation of Sputtering Processes in Strontium Iridate Thin Films

  • Fuentes, Víctor
  • Balcells, Lluis
  • Konstantinović, Z.
  • Martínez, Benjamín
  • Pomar, Alberto
The growth of epitaxial thin films from the Ruddlesden–Popper series of strontium iridates by magnetron sputtering is analyzed. It was found that, even using a non-stoichiometric target, the films formed under various conditions were consistently of the perovskite-like n = ∞ SrIrO3 phase, with no evidence of other RP series phases. A detailed inspection of the temperature–oxygen phase diagram underscored that kinetics mechanisms prevail over thermodynamics considerations. The analysis of the angular distribution of sputtered iridium and strontium species indicated clearly different spatial distribution patterns. Additionally, significant backsputtering was detected at elevated temperatures. Thus, it is assumed that the interplay between these two kinetic phenomena is at the origin of the preferential nucleation of the SrIrO3 phase. In addition, strategies for controlling cation stoichiometry off-axis have also been explored. Finally, the long-term stability of the films has been demonstrated., This work has received funding from the “Spanish Ministry of Science and Innovation” through “Severo Ochoa” (CEX2019-000917-S) and “OXISOT” (PID2021-128410OB-I00). Z.K. acknowledges funding provided by the Institute of Physics Belgrade (University of Belgrade, Serbia). This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 101007417, having benefited from the access provided by ICMAB within the framework of the NFFA-Europe Pilot Transnational Access Activity, proposal ID352., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Combining thermal scanning probe lithography and dry etching for grayscale nanopattern amplification

  • Erbas, Berke
  • Conde Rubio, Ana
  • Liu, Xia
  • Pernollet, Joffrey
  • Wang, Zhenyu
  • Bertsch, Arnaud
  • Penedo, Marcos
  • Fantner, Georg
  • Banerjee, Mitali
  • Kis, Andras
  • Boero, Giovanni
  • Brugger, Juergen
Grayscale structured surfaces with nanometer-scale features are used in a growing number of applications in optics and fluidics. Thermal scanning probe lithography achieves a lateral resolution below 10 nm and a vertical resolution below 1 nm, but its maximum depth in polymers is limited. Here, we present an innovative combination of nanowriting in thermal resist and plasma dry etching with substrate cooling, which achieves up to 10-fold amplification of polymer nanopatterns into SiO2 without proportionally increasing surface roughness. Sinusoidal nanopatterns in SiO2 with 400 nm pitch and 150 nm depth are fabricated free of shape distortion after dry etching. To exemplify the possible applications of the proposed method, grayscale dielectric nanostructures are used for scalable manufacturing through nanoimprint lithography and for strain nanoengineering of 2D materials. Such a method for aspect ratio amplification and smooth grayscale nanopatterning has the potential to find application in the fabrication of photonic and nanoelectronic devices., The authors thank the Center of Micro/Nanotechnology (CMi) of EPFL for fabrication facilities and the Interdisciplinary Centre for Electron Microscopy (CIME) of EPFL for FIB and SEM facilities. We also thank Damien Bertrand, Leonardo Cele, Guillaume Pellerin, Fabienne Bobard, Dr. Lucie Navratilova, Dr. Cyrille Hibert and Prof. Francesc Perez-Murano for their support with fabrication processes and metrology. This work received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation program (Project MEMS4.0, ERC-2016-ADG, grant agreement No. 742685) and the EU’s H2020 framework program for research and innovation under grant agreement n. 101007417, NFFA-Europe Pilot Project. M.B. acknowledges the support of SNSF Eccellenza grant No. PCEGP2_194528, and support from the QuantERA II Programme that has received funding from the European Union’s Horizon 2020 research and innovation program under Grant Agreement No 101017733. G.F. and M.P. received funding through the European research council H2020 - UE Framework Programme for Research & Innovation (2014-2020); ERC-2017-CoG; InCell; Project number 773091, and the Swiss National Science Foundation through grant 200021_182562., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hybrid Metrology for Nanostructured Optical Metasurfaces

  • Murataj, Irdi
  • Angelini, Angelo
  • Cara, Eleonora
  • Porro, Samuele
  • Beckhoff, Burkhard
  • Kayser, Yves
  • Hönicke, Philipp
  • Ciesielski, Richard
  • Gollwitzer, Christian
  • Soltwisch, Victor
  • Perez Murano, Francesc X.
  • Fernández-Regúlez, Marta
  • Carignano, Stefano
  • Boarino, Luca
  • Castellino, Micaela
  • Ferrarese Lupi, Federico
Metasurfaces have garnered increasing research interest in recent years due to their remarkable advantages, such as efficient miniaturization and novel functionalities compared to traditional optical elements such as lenses and filters. These advantages have facilitated their rapid commercial deployment. Recent advancements in nanofabrication have enabled the reduction of optical metasurface dimensions to the nanometer scale, expanding their capabilities to cover visible wavelengths. However, the pursuit of large-scale manufacturing of metasurfaces with customizable functions presents challenges in controlling the dimensions and composition of the constituent dielectric materials. To address these challenges, the combination of block copolymer (BCP) self-assembly and sequential infiltration synthesis (SIS), offers an alternative for fabrication of high-resolution dielectric nanostructures with tailored composition and optical functionalities. However, the absence of metrological techniques capable of providing precise and reliable characterization of the refractive index of dielectric nanostructures persists. This study introduces a hybrid metrology strategy that integrates complementary synchrotron-based traceable X-ray techniques to achieve comprehensive material characterization for the determination of the refractive index on the nanoscale. To establish correlations between material functionality and their underlying chemical, compositional and dimensional properties, TiO2 nanostructures model systems were fabricated by SIS of BCPs. The results from synchrotron-based analyses were integrated into physical models, serving as a validation scheme for laboratory-scale measurements to determine effective refractive indices of the nanoscale dielectric materials., Project funded by the European Union─NextGenerationEU under the National Recovery and Resilience Plan (NRRP), Mission 04 Component 2 Investment 3.1|Project Code: IR0000027-CUP: B33C22000710006-iENTRANCE@ENL: Infrastructure for Energy TRAnsition aNd Circular Economy @EuroNanoLab. Part of this work was supported by the European project 21GRD01 OpMetBat. The project has received funding from the European Partnership on Metrology, cofinanced from the European Union’s Horizon Europe Research and Innovation Programme, and by Participating States. Part of this work has been carried out in the framework of the EMPIR Researcher Mobility Grant 20FUN06-RMG2. Part of this work has been carried out at Nanofacility Piemonte, a laboratory supported by the ‘“Compagnia di San Paolo”’ Foundation, and at the QR Laboratories, INRiM. This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 101007417 having benefitted from the access provided by IMB-CNM CSIC (Spain) within the framework of the NFFA-Europe Pilot Transnational Access Activity, proposal ID-090. In particular, the authors thank Xavier Borrisé Nogué, Albert Guerrero Barbero, and Miguel Zabala Garcìa of IMB-CNM CSIC for their kind support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Development of hard X-ray photoelectron spectroscopy in liquid cells using optimized microfabricated silicon nitride membranes

  • Capone, F.
  • Muntada, Olga
  • Ramírez, Jéssica Casandra
  • Esplandiú, María J.
  • Dedryvère, R.
  • Grimaud, A.
  • Lassalle-Kaiser, B.
  • Céolin, D.
  • Perez Murano, Francesc X.
  • Rueff, J. P.
  • Fraxedas, J.
We present first hard X-ray photoelectron spectroscopy (HAXPES) results of aqueous salt solutions and dispersions of gold nanoparticles in liquid cells equipped with specially designed microfabricated thin silicon nitride membranes, with thickness in the 15-25 nm range, mounted in a high-vacuum-compatible environment. The experiments have been performed at the HAXPES endstation of the GALAXIES beamline at the SOLEIL synchrotron radiation facility. The low-stress membranes are fabricated from 100 mm silicon wafers using standard lithography techniques. Platinum alignment marks are added to the chips hosting the membranes to facilitate the positioning of the X-ray beam on the membrane by detecting the corresponding photoemission lines. Two types of liquid cells have been used, a static one built on an Omicron-type sample holder with the liquid confined in the cell container, and a circulating liquid cell, in which the liquid can flow in order to mitigate the effects due to beam damage. We demonstrate that the membranes are mechanically robust and able to withstand 1 bar pressure difference between the liquid inside the cell and vacuum, and the intense synchrotron radiation beam during data acquisition. This opens up new opportunities for spectroscopic studies of liquids., This project has received funding from the European Union's Horizon 2020 research and innovation programme, under grant agreement No. 101007417 NFFA-Europe Pilot and the Spanish Ministry of Science and Innovation (MCIN) under contract No. PID2021-124568NB-I00. The ICN2 is funded by the CERCA program/Generalitat de Catalunya. The ICN2 is supported by the Severo Ochoa Centres of Excellence programme, grant CEX2021-001214-S, funded by MCIN/AEI. Support through the María de Maeztu grant CEX2023-001397-M funded by MICIU/AEI is acknowledged. We acknowledge funding from Generalitat de Catalunya through the 2021-SGR-00644 project. We also acknowledge the scientific exchange and support of the Centre for Molecular Water Science (CMWS). This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No. 957189. The project is part of BATTERY 2030+, the large-scale European research initiative for inventing the sustainable batteries of the future. We thank SOLEIL for the provision of beam time (proposal Nos. 20220156 and 20230319)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001214-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001397-M)., We acknowledge support for the publication fee by the CSIC Open Access Publication Support Initiative through its Unit of Information Resources for Research (URICI)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Development of hard X-ray photoelectron spectroscopy in liquid cells using optimized microfabricated silicon nitride membranes [Dataset]

  • Capone, F.
  • Muntada, Olga
  • Ramírez, Jéssica Casandra
  • Esplandiú, María J.
  • Dedryvère, R.
  • Grimaud, A.
  • Lassalle-Kaiser, B.
  • Céolin, D.
  • Perez Murano, Francesc X.
  • Rueff, J. P.
  • Fraxedas, J.
[Description of methods used for collection/generation of data] Data acquired with a high-kinetic-energy Scienta EW 4000 hemispherical analyser installed on the HAXPES endstation of the GALAXIES beamline of the French national synchrotron facility SOLEIL (France) [Methods for processing the data] CasaXPS software., Original raw data (uncorrected energies) of HAXPES spectra obtained at the HAXPES endstation of the GALAXIES beamline at SOLEIL synchrotron facility (France). Each spectrum is displayed in a two-column format, kinetic energy (X) vs. HAXPES intensity (Y). Photon energies are indicated for each figure., [FIGURE 5] HAXPES raw data of the Au 4f region in kinetic energy (X) vs. intensity (Y) columns of a 40 nm Au film (au_film_40nm), a dispersion of Au nanoparticles on a 25 nm-thick membrane in air (au_np_cell16), a dispersion of Au nanoparticles in MilliQ water (au_np_cell17) and a Au film treated with oxygen plasma and measured with 1486.6 eV photons (au_film_O2_plasma, data from DOI: 10.1021/acs.accounts.8b00241). Photon energy = 5 keV., [FIGURE 6] HAXPES raw and normalized (norm) data of the (a) N 1s, (b) O 1s, (c) C 1s and (d) F 1s lines obtained with 7 keV photons and using 20 nm thick membranes. Liquid cells filled with: air (S2), vacuum (S4), with air and with a ca 5 nm-thick amorphous carbon coating deposited in the inner part of the membrane (S7) and with 60 ml of the LP57 electrolyte (1 M LiPF6 in EC:EMC 3:7) and with the ca 5 nm-thick carbon coating (S6). The formulas used for normalization (heights normalized to their corresponding maxima) are displayed in the corresponding Y columns. In Fig. 6(d) a least-squares fit using the CasaXPS software after a Shirley-type background subtraction using a combination of Gaussian (70%) and Lorentzian (30%) functions under the constraint of identical full width at half-maximum (FWHM) for all components is shown. Raw and corrected kinetic energies are given., [FIGURE 7] HAXPES raw data of the (a) Na 1s region of a 3.5 M NaCl aqueous solution and (b) Cs 3d and (c) Cs 4d lines of a 2.6 M aqueous solution of CsCl obtained with 7 keV photons and using 15 nm membranes., [FIGURE S1] (Top) simulation of the inelastic mean free path (nm) as a function of the kinetic energy in silicon nitride using the TPP-2M model and assuming a 3.44 gr cm-3 density for silicon nitride. (Bottom) Simulated HAXPES spectra assuming a 15 nm thick silicon nitride layer on a CsCl substrate in the 3-10 keV photon energy range., European Union’s Horizon 2020 research and innovation programme, under grant agreement No. 101007417 NFFA-Europe Pilot. Spanish Ministry of Science and Innovation (MCIN) under contract No. PID2021-124568NB-I00. ICN2 is funded by the CERCA program/Generalitat de Catalunya. ICN2 is supported by the Severo Ochoa Centres of Excellence programme, grant CEX2021-001214-S, funded by MCIN/AEI. Support through the Marıa de Maeztu grant CEX2023-001397-M funded by MICIU/AEI is acknowledged. Generalitat de Catalunya through the 2021-SGR-00644 project. European Union’s Horizon 2020 research and innovation programme under grant agreement No. 957189., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2021-001214-S)., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001397-M)., File List: Fig_5.xls; Fig_6a.xls, Fig_6b.xls, Fig_6c.xls, Fig_6d.xls, Fig_7.xls, Fig_S1.xls, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Deterministic grayscale nanotopography to engineer mobilities in strained MoS2 FETs

  • Liu, Xia
  • Erbas, Berke
  • Conde Rubio, Ana
  • Rivano, Norma
  • Wang, Zhenyu
  • Jiang, Jin
  • Bienz, Siiri
  • Kumar, Naresh
  • Sohier, Thibault
  • Penedo, Marcos
  • Banerjee, Mitali
  • Fantner, Georg
  • Zenobi, Renato
  • Marzari, Nicola
  • Kis, Andras
  • Boero, Giovanni
  • Brugger, Juergen
Field-effect transistors (FETs) based on two-dimensional materials (2DMs) with atomically thin channels have emerged as a promising platform for beyond-silicon electronics. However, low carrier mobility in 2DM transistors driven by phonon scattering remains a critical challenge. To address this issue, we propose the controlled introduction of localized tensile strain as an effective means to inhibit electron-phonon scattering in 2DM. Strain is achieved by conformally adhering the 2DM via van der Waals forces to a dielectric layer previously nanoengineered with a gray-tone topography. Our results show that monolayer MoS2 FETs under tensile strain achieve an 8-fold increase in on-state current, reaching mobilities of 185 cm²/Vs at room temperature, in good agreement with theoretical calculations. The present work on nanotopographic grayscale surface engineering and the use of high-quality dielectric materials has the potential to find application in the nanofabrication of photonic and nanoelectronic devices., The authors thank the Center of Micro/Nanotechnology (CMi) of EPFL for the AFM facility support. X.L., B.E., A.C., G.B., and J.B. acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation program (Project “MEMS 4.0”, ERC-2016-ADG, grant agreement No. 742685), NFFA-Europe Pilot Project (the EU’s H2020 framework program for research and innovation, grant agreement No. 101007417). X.L. acknowledges fundings from the National Natural Science Foundation of China (No. 62274013) and the National Key Research and Development Program of China (No. 2023YFB3405600). M.B. acknowledges the support of SNSF Eccellenza grant No. PCEGP2_194528, and support from the QuantERA II Programme that has received funding from the European Union’s Horizon 2020 research and innovation program under Grant Agreement No 101017733. R.Z. acknowledges funding from the Swiss National Science Foundation through the NCCR MARVEL (project number 200021-143636) and the R’Equip program (grant number 206021-205312), as well as computational support from the Swiss National Supercomputing Centre. N.R. and N.M. acknowledge funding from the Swiss National Science Foundation (SNSF) and its National Centre of Competence in Research MARVEL on ‘Computational Design and Discovery of Novel Materials’ (grant number 182892). They also acknowledge computational support from the Swiss National Supercomputing Centre CSCS under project ID mr24. Z.W. and A.K. acknowledge financing from European Union’s Horizon 2020 research and innovation program under grant agreements 881603 (Graphene Flagship Core 3) and No 964735 (EXTREME-IR). G.F. and M.P. received funding through Innosuisse (AFM with PORT: Atomic force microscope with photothermal off-resonance tapping, grant number 7879, ext ref. 36938.1 IP-EE), FNS (Video-rate nanomechanical properties mapping using atomic force microscopy, grant number 7288, ext. ref. 200021_182562), H2020 (InCell - High speed AFM imaging of molecular processes inside living cellsInCell - High speed AFM imaging of molecular processes inside living cells, grant number 6823, ext ref. 773091, ETH Domain (An ecosystem for community driven scanning probe microscopy research and development, grant number 10126) and Eurostars (Correlated Analysis System for in-vivo Inspection of Semi-Conductor Process Wafers, grant number 9953, ext. ref. E!665 CAS-C)., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Graphene in Water is Hardly Ever Neutral

  • Boulbet-Friedelmeyer, Luna
  • Pécastaings, Gilles
  • Labrugère-Sarroste, Christine
  • Faraudo, Jordi
  • Pénicaud, Alain
  • Drummond, Carlos
Graphene in water is electrically charged in most conditions. The level of charge can be large enough to stabilize single (or few) layer graphene colloidal dispersions in water, without the need of using any other additive. In this work, potentiometric titration, isothermal titration calorimetry, electrokinetic measurements, Density Functional Theory calculations, Raman Spectroscopy, and direct force measurements using Atomic Force Microscopy to investigate this charge and explore its origin are combined. The body of data collected suggests that this charge is a consequence of the interaction between water ions (hydroxide and hydronium) and graphene, and can be conveniently tuned (in magnitude and sign) by changing the pH of water., L.B. thanks l'Association nationale de la recherche et de la technologie ANRT and Carbon Waters for a PhD grant. C.D. and A.P. thank l'Agence Nationale de la Recherche, project 2D-MEMBA, ANR-21-CE09-0034-01. This project has received funding from the European Union's Horizon Europe research and innovation program under grant agreement No 101007417, having benefited from the access provided by CSIC-ICMAB in Barcelona within the framework of the NFFA-Europe Pilot Transnational Access Activity, proposal ID309. J. F. acknowledges the financial support from the AGAUR agency (Grant 2021SGR01519) and the MCIN/AEI/10.13039/501100011033 agency through the “Severo Ochoa” Program for Centers of Excellence in R&D (CEX2019-000917-S) awarded to ICMAB., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000917-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Microstructure of VO2 thin films synthesized by pulsed laser deposition

  • Romanitan, Cosmin
  • Caicedo, José Manuel
  • Pascu, Razvan
  • Mihalache, Iuliana
  • Gavrila, Raluca
  • Stoian, Marius
  • Djourelov, Nikolay
  • Padilla-Pantoja, Jessica
An open – access publication., In this paper, pulsed laser deposition (PLD) at low partial oxygen pressure (∼ 10 mTorr) was used to obtain VO thin films. During the PLD, the deposition temperature and number of pulses were varied in order to obtain a good sample crystallinity. It was showed by atomic force microscopy (AFM) micrographs that the mean grain size increased from ∼ 40 nm to ∼ 90 nm at a variation of the deposition temperature from 400 C to 500 C. Further, by increasing of both substrate temperature and number of pulses, the mean grain size increases to 220 nm. According to the Rietveld refinement of the experimental X-ray diffraction (XRD) pattern, within the grain size increasing, the mean crystallite size increased from 14 nm to 22 nm, as well as a decreasing of the lattice strain from 0.29% to 0.20%. These dependencies further imply a decreasing of the dislocation density of 2.3 to 0.9 × 10 cm. At the same time, the optical band gap decreased from 0.72 eV (400 C) to 0.66 eV (500 C), reaching 0.60 eV (600 C). Further investigations performed by X-ray photoelectron spectroscopy (XPS) showed the vanadium oxide presence, by the spin-orbit splitting of approximately 7.5 eV between V 2p and V 2p orbitals. Finally, the electrical measurements done in the range of 250 − 370 K reveal a close relationship between the dislocation density and the observed resistance-temperature dependence., This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 101007417 having benefitted from the access provided by ICN2 in Bellaterra, Barcelona within the framework of the NFFA-Europe Pilot Transnational Access Activity, proposal ID282. This research was partially financed by Romanian Core Program PNCDI 2022-2027 “Cercetari avansate in dispozitive micronano-electronice, fotonice, senzori si microsisteme pentru aplicatii societale- µNanoEl” cod 2307/29.12.2022 (2023-2026) and PN 23.21.01.06 project; financed by the Ministry of Research, Innovation and Digitalization. Also, this work was supported by a grant of the Ministry of Research, Innovation and Digitization, CCCDI- UEFISCDI, project number PN-III-P2-2.1PED-2021-2688., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effective Utilization of Nanoporosity and Surface Area Guides Electrosynthesis over Soft-Landed Copper Oxide Catalyst Layers

  • Arnouts, Sven
  • Choukroun, Daniel
  • Napal, Ilargi
  • Tajuelo-Castilla, G.
  • Prieto Serrano, Javier
  • Claes, Nathalie
  • Daems, Nick
  • Nappini, Silvia
  • Magnano, Elena
  • Santoro, Gonzalo
  • Bals, Sara
  • Martín-Gago, José A.
  • Breugelmans, Tom
Porous nanomaterials find wide-ranging applications in modern medicine, optoelectronics, and catalysis, playing a key role in today's effort to build an electrified, sustainable future. Accurate in situ quantification of their structural and surface properties is required to model their performance and improve their design. In this article, we demonstrate how to assess the porosity, surface area and utilization of a model nanoporous soft-landed copper oxide catalyst layer/carbon interface, which is otherwise difficult to resolve using physisorption or capacitance-based methods. Our work employs electron tomography to characterize the three-dimensional structure of the catalyst layer and combines it with in situ soft X-ray absorption spectroscopy and lead underpotential deposition data to probe the stability and utilization of the catalyst layer under potential bias. The analysis proves that a significant share of the original surface area is exploited, and thus explains product distribution and crossover trends in the electrosynthesis of C2+ products from carbon monoxide., The authors acknowledge financial support from NFFA-NEP -European Union’s Horizon 2020 research and innovation program under grant agreement No. 101007417, proposal IDs159 and 472, and by the European Research Council (ERC CoGNo. 815128 RealNANO) to S.B. G.T.C. acknowledges funding from the Comunidad Autónoma de Madrid (grant No. PEJ-2021-AI/IND-21143). This work has been partially funded bygrant No. PID2023-149077OB-C31 funded by MCIN/AEI/10.13039/501100011033 and grant No. PLEC2021-007906 funded by MCIN/AEI/10.13039/501100011033 by the “Euro-pean Union NextGenerationEU/PRTR”. Partial funding byPhotosurf-CM (Y2020/NMT-6469) project funded by Comunidad Autónoma de Madrid and cofinanced by EuropeanStructural Funds is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Epitaxial Growth of Ni-Mn-Ga on Al2O3(112¯0) Single-Crystal Substrates by Pulsed Laser Deposition

  • Pinedo-Cuba, Manuel G.
  • Caicedo, José Manuel
  • Padilla-Pantoja, Jessica
  • Quispe-Marcatoma, Justiniano
  • Landauro, Carlos V.
  • Peña-Rodríguez, Víctor A.
  • Santiso, José
This article belongs to the Special Issue Surface Engineering of Thin Films., Magnetic shape memory alloys have attracted considerable attention due to their multifunctional properties. Among these materials, Ni-Mn-Ga alloys are distinguished by their ability to achieve up to 10% strain when exposed to a magnetic field, a characteristic predominantly observed in single-crystal samples. Consequently, it is essential to develop nanomaterials with a crystal structure closely resembling that of a single crystal. In this study, an epitaxial Ni-Mn-Ga thin film was fabricated using Pulsed Laser Deposition on an Al2O3 ( 11 2 ¯ 0 ) single-crystal substrate. The crystal structure was characterised through X-ray diffraction methodologies, such as symmetrical 2 θ − ω scans, pole figures, and reciprocal space maps. The results indicated that the sample was mainly in a slightly distorted cubic austenite phase, and some incipient martensite phase also appeared. A detailed microstructural analysis, performed by transmission electron microscopy, confirmed that certain regions of the sample exhibited an incipient transformation to the martensite phase. Regions closer to the substrate retained the austenite phase, suggesting that the constraint imposed by the substrate inhibits the phase transition. These results indicate that it is possible to grow high crystalline quality thin films of Ni-Mn-Ga by Pulsed Laser Deposition., The authors acknowledge PROCIENCIA-CONCYTEC for funding the project under contract code PE501079047-2022. This research was further supported by the Universidad Nacional Mayor de San Marcos (Project numbers: B23131861 and B22139675x). G.P. acknowledges funding from the European Union’s Horizon 2020 research and innovation program under the Marie Sklodowska-Curie grant agreement No. 101007825 (ULTIMATE-I Project) for a research stay at ICN2. This research was also funded by the European Union’s Horizon 2020 research and innovation programme under grant agreement No. 101007417, having benefitted from the access provided by ICN2 in Bellaterra (Spain) within the framework of the NFFA-Europe Pilot Transnational Access Activity, proposal ID530. ICN2 is supported by the Severo Ochoa program from Spanish MCIN/AEI (Grant No.: CEX2021-001214-S) and is funded by the CERCA Programme., With funding form the Spanish government through the "Severa Ochoa Centre of Excellence" accreditation (CEX2021-001214-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Combination of Thermal Scanning Probe Lithography and Directed Self-Assembly of Block Copolymers

  • Uranga-Granados, Iker
  • Erbas, Berke
  • Torres-Vila, Pol
  • Bertsch, Arnaud
  • Llobet, Jordi
  • Bausells, Joan
  • Perez Murano, Francesc X.
  • Brugger, Juergen
  • Fernández-Regúlez, Marta
The fabrication of semiconductor quantum devices necessitates sub-20 nm features and high-density patterning, often exceeding the capabilities of current state-of-the-art lithographic techniques. To address this challenge, in this work, the combination of top-down thermal scanning probe lithography (t-SPL) and pattern transfer with bottom-up directed self-assembly (DSA) of block copolymers (BCP) is presented as a new lithography process suitable for quantum device fabrication. Nanohole arrays of varying shapes and sizes were patterned into SiO2 using a combination of t-SPL and reactive ion etching (RIE) for 5x depth-amplified pattern transfer. These arrays served as guiding patterns, inducing three distinct orderings of block copolymers (BCP): pattern hole shrink (PHS), pattern hole doubling (PHD), and high-pitched PHD. SEM images have been analyzed by image processing to determine guiding pattern/DSA pattern placement accuracy. It has been determined that the guiding pattern/DSA offset is sub-10 nm, so it does not hinder the pattern placement control lent by t-SPL. This combined t-SPL/DSA lithography process, capable of creating complex, high-resolution patterns with precise placement, holds a significant promise for fabricating advanced quantum devices., This work was developed in the context of the NFFA NEP network and funded by the NFFA-Europe-Pilot (n. 101007417 from 1/03/2021 to 28/02/2026) project. Additionally, support through the Maria de Maeztu grant CEX2023- 001397-M and projects PID2021-126046OB-C21 and PDC2023-145930-I00 funded by MCIN/AEI is acknowledged. Special thanks to the IMB-CNM and EPFL CMI clean room staffs for support in the processing and characterization of the samples., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Influence of the graphene oxide precursor in laser-synthetized hybrid photocatalysts for the H2 production by glycerol photoreforming

  • Gutiérrez Gómez, Susana
  • Peral, José
  • Buyens, Dominique
  • Gyorgy, Eniko
  • Pérez del Pino, Ángel
The present study reports the versatile synthesis of photocatalysts composed of nitrogen-doped reduced graphene oxide (NrGO) flakes coated with TiO2-FeOx nanostructures using ultraviolet (UV) pulsed laser irradiation in a liquid environment. Different commercial graphene oxide (GO) sources were used, revealing a significant influence on the structural, compositional, and functional properties of the final photocatalysts. The H2 production via water-splitting reaction using glycerol as sacrificial agent (photoreforming), ranged from 0.06 to 2.1 μmol H2/g in 3.5 h depending on the GO precursor used. The best photocatalysts were those that showed a reduction in the TiO2 material with a Ti(IV)/Ti(III) atomic ratio about 2.0–2.4, as well as a reduction and N-doping of GO, with 20–23 at % of C, and 4–6 at % of N. The light-scattering nature of the photocatalysts also had a significant effect on the H2 production yield., The authors thank the financial support through the grant TED2021–130477B-I00 funded by MCIN/AEI/10.13039/501100011033 and by the European Union NextGeneration EU/PRTR, as well as the grants CEX2023–001263-S from the State Investigation Agency, through Severo Ochoa Program for Centers of Excellence in R&D, and 2022 SGR 0936 from AGAUR of Generalitat de Catalunya. This project also received funding from the European Union’s Horizon 2020 research and innovation programme, under the grant agreement No 101007417 NFFA-Europe Pilot (project ID 476), having benefited from the access provided by the SIAM platform at the University of Namur for XPS characterization, and Karlsruhe Institute of Technology, Institute of Microstructure Technology installations, for NMR analyses. The authors also acknowledge the support of Graphenea, Salvador Bartolomé (Fluorescence spectroscopy service of UAB), the scientific-technical and prototyping services of ICMAB (particularly, to Amable Bernabé, Xavier Rodriguez, and Gerard Albujer), as well as Rachel Gouttenbaron (SIAM) to this research., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Spatially Resolved Photodoping of Oxygen-Deficient YBa2Cu3O7−δ Resonators

  • Lejeune, Nicolas
  • Nulens, Lukas
  • Li, Huidong
  • Günkel, Thomas
  • Fabrega, Lourdes
  • Palau, Anna
  • Van de Vondel, Joris
  • Silhanek, Alejandro V.
Oxygen-depleted YBa<inf>2</inf>Cu<inf>3</inf>O<inf>7−δ</inf> exhibits a substantial drop in the normal-state resistivity and an increase in the superconducting critical temperature when illuminated with visible light. The photo-induced states are metastable, slowly decaying at high temperatures and essentially persistent at low temperatures. In this work, this effect is exploited to modify the response of half-wavelength YBa<inf>2</inf>Cu<inf>3</inf>O<inf>7−δ</inf> resonators and simultaneously the high-sensitivity of the resonant circuit is used to investigate the persistent photodoping of this material. Under illumination, the bolometric effect and photodoping are clearly distinguished by the different time scales associated with each mechanism. Using a 60 µm-wide laser spot, the properties of the resonator are locally and reversibly modified, and the position-dependent sensitivity of the device is demonstrated. This enables the direct imaging of standing waves at both the fundamental resonance and the second harmonic., The authors acknowledge financial support from Fonds de la Recherche Scientifique - FNRS under the Grant Weave -PDRT.0208.23 and the Spanish Ministry of Science and Innovation MCIN/ AEI /10.13039/501100011033/ through the “Severo Ochoa” Programme for Centres of Excellence CEX2023–001263–S, HTSUPERFUN PID2021–124680OB–I00, co–financed by ERDF A way of making Europe. The Nanolito networking project RED2022–134096–T and the Catalan Government with Grant No. 2021-SGR-00440. The Research Foundation and by COST (European Cooperation in Science and Technology) [www.cost.eu] through COST Action SUPERQUMAP (CA 21144). This research was supported and funded by an interuniversity BOF project (IBOF-23-065). N.L. acknowledges support from FRS-FNRS (Research Fellowships FRIA). This project received funding from the European Union's Horizon 2020 research and innovation programme under Grant agreement No. 101007417 having benefited from the access to the facilities of ICN2 - Fundacio Institut Català de Nanociència i Nanotecnologia, Barcelona, (ES) within the framework of the NFFA-Europe Pilot Transnational Access Activity, proposal ID557., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Maximizing Reducing Potential of Fe3O4 Nanoparticles for Efficient Removal of Cr(VI) in Drinking Water

  • Efstathiou, Vasiliki
  • Savvantidis, Georgios
  • Virgiliou, Christina
  • Kokkinos, Evgenios
  • Balcells, Lluis
  • Simeonidis, Konstantinos
This article belongs to the Special Issue New Technologies to Ensure Safe Drinking Water., The dimensions and the reduction capacity of Fe3O4 nanoparticles are considered to be the key parameters in achieving the successful, efficient removal of hexavalent chromium, aiming for drinking water purification. This research study focuses on the optimization of reaction parameters during the oxidative precipitation of FeSO4 carried out in a microwave-heated plug-flow reactor, to realize the preparation of Fe3O4 nanoparticles with an increased reduction potential as reflected in the Fe2+/Fe3+ ratio by approximating the ideal value of 0.5. In particular, the coupling of synthesis with features that allow for control of the oxidation extent, and include the addition of a reducing agent, an increase in ageing temperature, and inhibition of aggregation, were tested as potential approaches to tune the reducing potential and overcome reported Cr(VI) capture efficiencies provided by Fe3O4 nanoparticles. The evaluation results showed that adding a reductant after nanoparticle formation inhibits spontaneoussurface oxidation, bringing an improvement in the Cr(VI) uptake capacity for a residual concentration equal to the new EU regulation limit, by around 40%, reaching a value of 2.15 mg/g. However, working at an ageing temperature of around 100 °C resulted in an even better performance with an uptake increase of 120% and a capacity value of 3.45 mg/g. Finally, adding nanoparticles in the form of a dispersion instead of a dried powder provides an extra 10% improvement as a consequence of limited aggregation., This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 101007417, having benefited from the access provided by CSIC-ICMAB in Barcelona within the framework of the NFFA-Europe Pilot Transnational Access Activity, proposal ID735., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Lennard–Jones Parameter Fitting for Gold/Water Interaction Based on Structural Analysis: A QM, MM, and QM/MM Study

  • Bancells i Blazquez, Pere
  • Pedron, Federico N.
  • Alcaraz Torres, Anthoni
  • Moraes, Elizane Efigenia de
  • Cole, Ivan
  • Freitas Martins, Ernane de
This article belongs to the Section Theory and Simulation of Nanostructures, The interaction between water and metallic interfaces is crucial in many fields, and accurate modeling requires good parametrizations using reference data. In classical molecular dynamics (MD), an important part of this interaction is described using the Lennard–Jones (LJ) potential. However, previously reported LJ parameters are not always optimal for capturing the metal/water interactions observed in ab initio descriptions such as density functional theory (DFT). Therefore, well-tailored LJ parameters are necessary to improve the description of water structuring metals in classical MD. The usual route for obtaining LJ parameters involves energetic analysis, where the energies of various structures are obtained via DFT calculations and then matched with the energies obtained using the LJ potentials by varying the sigma/epsilon parameters. Here, we show a different approach to fit LJ parameters for metal/water interactions, based on structural analysis. We report several classical MD simulations for gold/water, varying the sigma/epsilon parameters, comparing the resulting water structuring with that obtained using DFT. Additionally, we test these parameters in quantum mechanics/molecular mechanics (QM/MM) MD simulations, where electrostatic interactions are enabled. Our results demonstrate that the proposed approach can improve the LJ parameters reported in the literature and potentially develop parameters for more complex systems where the water structure above metallic surfaces plays a significant role. Finally, within this proposed approach, the water density profile obtained in hybrid QM/MM calculations, where water is treated as MM at a substantially reduced cost, closely matches the description it would have if treated as QM., Work supported by the Spanish MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe through Grant PID2022-139776NB-C62. This project has received funding from EuroHPC JU-EU under the “MAX” project (Grant No. 101093374), and from Grant PCI2022-134972-2 funded by the Spanish MCIN/AEI/10.13039/501100011033 and the European Union NextGenerationEU/PRTR. In addition, this work was supported by the EU’s H2020 framework programme for research and innovation under grant agreements NFFA-Europe Pilot Transnational Access Facility (Grant No. 101007417), having benefited from the access provided by ICN2 in Barcelona within the framework of the NFFA proposals [ID801, ID548, and ID900]. The ICN2 is supported by the Severo Ochoa Centres of Excellence programme, Grant No. CEX2021-001214-S, funded by MCIN/AEI/10.13039.501100011033., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Cation-induced structural/morphological control of ZnO under alkaline hydrothermal conditions: Influence on photocatalytic activity

  • Kuzmanović, Bojana
  • Vujković, Milica
  • Mamula, Bojana Paskaš
  • Ilić, Mirjana Medić
  • Batalović, Katarina
  • Martínez Perea, Benjamín
  • Tomić, Nataša
This study investigates the hydrothermal synthesis of ZnO nanopowders using three different alkaline reagents: KOH, NaOH, and NH<inf>4</inf>OH, focusing on their morphological, structural, and photocatalytic properties. The resulting ZnO powders displayed distinct morphologies − from hexagonal rods and prismatic structures to a 3D butterfly-nebula-like morphology − depending on the base employed. Phase purity and structural characteristics were confirmed via X-ray diffraction (XRD) and Raman spectroscopy, while scanning and transmission electron microscopy (SEM/TEM) revealed significant morphological differences at multiple magnifications. When hydrothermally produced using KOH and NaOH, ZnO crystallizes into hexagonal prismatic rods along the [0001] direction, starting from a zinc hydroxide precipitate. However, its transition to Zn ammine complex occurs by replacing K<sup>+</sup>or Na<sup>+</sup>with NH<inf>4</inf><sup>+</sup>ions during hydrothermal reaction, which changes the preferential crystal growth, favoring the lateral direction. As a result, ZnO nanostructures with a 3D butterfly-nebula-like morphology are formed. This alteration influences the photocatalytic activity, which is assessed by monitoring the degradation of Reactive Orange 16 (RO16) dye under UV irradiation. The ZnO nanopowder synthesized using NaOH exhibited the highest photocatalytic efficiency, achieving complete degradation of the dye within 90 min. The sample prepared with KOH showed a faster degradation rate than the one synthesized with NH<inf>4</inf>OH, but still lower than that of the NaOH-based sample. These findings highlight the crucial influence of base selection during hydrothermal synthesis on the morphology, crystallite size, and photocatalytic behavior of ZnO nanostructures, providing insights for the design of more efficient materials for environmental remediation applications., This research was supported by funding through grant number 451-03-136/2025-03/200017 provided by the Ministry of Science, Technological Development and Innovation of the Republic of Serbia. This research was supported by the Science Fund of the Republic of Serbia, Grant No. 372, Harnessing Machine Learning for Green Energy Materials: Insights into Mxene/Polyaniline Composite Surface – GEMComp. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 101007417 having benefited from the access provided by Institute of Material Science of Barcelona in Barcelona within the framework of the NFFA–Europe Pilot Transnational Access Activity, proposal ID543. We sincerely thank Dr. Mirjana Novaković for her generous assistance with the additional electron microscopy measurements, careful analysis of the results, and valuable advice, which greatly contributed to the quality of this work. We also wish to express our gratitude to Dr. Miloš Milović and Dr. Dragana Jugović for their helpful discussions and valuable advice., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2023-001263-S)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

In Situ Characterization of Strontium Titanium Ferrite Perovskites for Application as Electrodes of Solid Oxide Cells

  • Diaz Lacharme, Maria Carmenza
  • Marasi, Martina
  • Pérez-Dieste, Virginia
  • Ballesteros, Belén
  • Donazzi, Alessandro
This study investigates the redox behavior, the surface composition, and the electrochemical performance of the Ni-doped Sr0.95(Ti0.3Fe0.63Ni0.07)O3 (STF-Ni) and SrTi0.3Fe0.7O3 (STF) perovskites under conditions relevant to solid oxide cell applications. The effect of Ni doping on exsolution and on its reversibility is examined with synergistic characterization techniques. In situ XRD experiments (in 5% H2, up to 750 °C) reveal that FeNi and FeNi3 coexist in alloyed Ni–Fe nanoparticles and that the exsolved Ni is only partially reincorporated in the lattice of STF-Ni on reoxidation in air. In contrast, the reduction of STF leads to the segregation of nonalloyed metallic Fe particles. In situ near-ambient pressure XPS experiments (20 mbar, 550 °C) show that Sr segregates on both perovskites as SrOx during reduction in pure H2, and that the exsolution of Ni and Fe enhances the segregation. Subsequent exposure to CO2 causes the formation of SrCO3 and compositional changes of the STF-Ni nanoparticles, which become richer in Ni due to the back-diffusion of Fe in the lattice. When applied as fuel electrodes of electrolyte-supported solid oxide cells, STF-Ni and STF exhibit distinct behaviors in H2 electro-oxidation and CO2 electrolysis. STF-Ni shows better performance than STF with 3% humidified H2 supply (450 vs 350 mW/cm2 at 0.5 V), while both electrodes achieve similar current density (−450 mA/cm2 at 1.4 V) in reversible CO2 electrolysis with a 50/50 CO/CO2 mixture. These performance differences primarily arise from the interaction with CO2, which causes SrCO3 formation, electrode passivation, and compositional modifications of the nanoparticles., This project has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No. 101007417, having benefited from the support provided by the ALBA Synchrotron and the Institut Català de Nanociència i Nanotecnologia (ICN2) in Barcelona (Spain) within the framework of the NFFA-Europe Pilot Transnational Access Activity, proposal ID547. The authors gratefully acknowledge Dr. Belen Ballesteros for the realization of the TEM experiments and Dr. Virginia Pérez Dieste and Dr. Aleksandr Missiul for technical support during the beamline sessions with the NAP-XPS experiments and XRD experiments, respectively. The authors also wish to thank Dr. Ferdinando Bassato for his support in the understanding of the NEXAFS data. The authors dedicate the work in honor of Professor Luca Lietti for his 65th birthday., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effects of Elevated Temperatures and Catalyst Layer Morphology on the Carbon Balance during Electrochemical CO Reduction

  • Rossen, A.
  • Daems, N.
  • Choukroun, D.
  • Tajuelo-Castilla, G.
  • Santoro, Gonzalo
  • Martín-Gago, José A.
  • Breugelmans, T.
9 pages, 5 figures, 1 table, The electrochemical reduction of carbon monoxide (CORR) offers a promising opportunity to convert renewable electricity into value-added C2+ chemicals, such as ethylene, ethanol, and acetate. While scaled electrolyzer systems are expected to operate at elevated temperatures, the impact of temperature on crossover during CORR remains underexplored. In this study, we systematically evaluate the influence of temperature (25–85 °C) on the CORR using various copper-based catalyst layers, cell configurations (flow-by and anion exchange zero-gap membrane cell), and processing conditions (anolyte concentration, current density, and temperature). At low current density (−50 mA cm–2), product selectivity is found to be insensitive to temperature across the full investigated range. In addition, elevated temperatures significantly suppress the crossover of liquid products to the anolyte, thus, improving the net carbon efficiency. At higher current densities, conventional sputtered Cu electrodes suffer from severe flooding and CO starvation, limiting performance and selectivity. To address this, spray-coated Cu/PTFE electrodes are introduced, combining porosity and hydrophobicity to stabilize performance. These electrodes enable study of the CORR at current densities and temperatures of up to 400 mA cm–2 and 85 °C, respectively. Overall, the study shows that the temperature primarily affects product transport rather than reaction pathways. Understanding thermal effects is critical for guiding the design of CORR systems capable of efficient, stable operation under thermally and industrially realistic conditions., D.C. and N.D. acknowledge financial support from NFFA-NEP European Union’s Horizon 2020 research and innovation program under grant agreement No. 101007417, proposal ID 472. A.R. was financially supported through a PhD fellowship for strategic basic research (grant Nos. 1S37222N and 1S37224N). This work was cofunded by the Flanders Industry Innovation Moonshot program for the action CLUE HBC.2021.0586 and the FWO (SBO grant number S005226N eSAF project). J.Á .M.-G., G.S., and G.T.-C. acknowledge funding through the Severo Ochoa Centres of Excellence program through Grant CEX2024-001445-S and the national plan PID2023-149077OB-C31.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Research data Set de datos (Dataset)

Determining the intrinsic electronic structure of radiation-sensitive surfaces with X-ray photoemission spectroscopy: Nafion films as a case study

  • Fraxedas, J.
  • Esplandiú, María J.
  • Muntada, Olga
  • Perez Murano, Francesc X.
  • Céolin, D.
  • Rueff, J. P.
[Description of methods used for collection/generation of data] Data acquired with a PHI-Genesis system from ULVAC-PHI located at ICN2 and a high-kinetic-energy Scienta EW 4000 hemispherical analyser installed on the HAXPES endstation of the GALAXIES beamline of the French national synchrotron facility SOLEIL (France)., [Methods for processing the data] CasaXPS software version CasaXPS - 2.3.27 PR5.6, Determining the intrinsic electronic structure of radiation-sensitive polymer surfaces with X-ray photoelectron spectroscopy (XPS) requires careful optimization. Prior to any consistent characterization, evaluating radiation-induced damage is mandatory to establish the optimal operating parameters for the specific XPS instrument. In this work, we present a systematic methodology to address this challenge using Nafion, a widely utilized polymer containing highly radiation-sensitive sulfonate groups. Specifically, we focus on the capacity of Nafion thin films to efficiently capture divalent metal cations, such as Cd2+ and Pb2+, which are common toxic contaminants in drinking water. Given that Nafion films offer promising potential for rapid water purification and environmental remediation, a detailed analysis is essential to elucidate the ion-exchange mechanisms operating at the Nafion/water interface., - European Union’s Horizon 2020 research and innovation programme, under grant agreement No. 101007417 NFFA-Europe Pilot. - Spanish Ministry of Science and Innovation (MCIN) under contract No. PID2021-124568NB-I00. - The ICN2 is funded by the CERCA program/Generalitat de Catalunya. - The ICN2 is supported by the Severo Ochoa Centres of Excellence programme, grant CEX2021-001214-S, funded by MCIN/AEI. - María de Maeztu grant CEX2023-001397-M financed by MICIU/AEI/10.13039/501100011033. - Generalitat de Catalunya through the 2021-SGR-00644 project., With funding from the Spanish government through the "Severo Ochoa Centre of Excellence" accreditation (CEX2023-001397-M)., File List: Fig_03a.opju; Fig_03b.opju; Fig_04a.opju; Fig_04b.opju; Fig_04c.opju; Fig_05a.opju; Fig_05b.opju; Fig_05c.opju; Fig_06.opju; Fig_07a.opju; Fig_07b.opju; Fig_S02.opju; Fig_S03.opju; Fig_S04.opju; Fig_S05.opju; Fig_S06.opju; Fig_S07.opju; Fig_S08.opju, Peer reviewed