Skip to main content

TALADRADO DE COMPONENTES HIBRIDOS CFRPS/TI Y TOLERANCIA AL DAÑO DEBIDO A MECANIZADO DURANTE EL COMPORTAMIENTO EN SERVICIO DE UNIONES ESTRUCTURALES AERONAUTICAS

DPI2017-89197-C2-1-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSIDAD CARLOS III DE MADRID

Resultados relacionados

Resultados totales (Incluyendo duplicados): 18
Encontrada(s) 1 página(s)

Docta Complutense
Publication Artículo científico (JournalArticle)

Numerical modelling of hip fracture patterns in human femur

  • Larrainzar Garijo, Ricardo
Background and objective: Hip fracture morphology is an important factor determining the ulterior surgical repair and treatment, because of the dependence of the treatment on fracture morphology. Although numerical modelling can be a valuable tool for fracture prediction, the simulation of femur fracture is not simple due to the complexity of bone architecture and the numerical techniques required for simulation of crack propagation. Numerical models assuming homogeneous fracture mechanical properties commonly fail in the prediction of fracture patterns. This paper focuses on the prediction of femur fracture based on the development of a finite element model able to simulate the generation of long crack paths. Methods: The finite element model developed in this work demonstrates the capability of predicting fracture patterns under stance loading configuration, allowing the distinction between the main fracture paths: intracapsular and extracapsular fractures. It is worth noting the prediction of different fracture patterns for the same loading conditions, as observed during experimental tests. Results and conclusions: The internal distribution of bone mineral density and femur geometry strongly influences the femur fracture morphology and fracture load. Experimental fracture paths have been analysed by means of micro-computed tomography allowing the comparison of predicted and experimental crack surfaces, confirming the good accuracy of the numerical model.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical analysis of mechanical behaviour of lattice and porous structures

  • Marco, Miguel
  • Miguélez, María Henar
  • Belda Ricardo|||0000-0003-3913-5773
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] Lattice and porous structures have attracted attention in scientific literature due to the development of 3D printers that facilitate their manufacturing. A thorough understanding of the mechanical behaviour of these structures is necessary. In this work, several lattice and porous structures are analysed using the finite element method. Eleven configurations have been studied using periodic boundary conditions, in order to numerically estimate their elastic mechanical properties (Young¿s modulus, shear modulus and Poisson¿s ratio) as a function of the structure porosity. In addition, a tensile fracture test has been modelled to analyse the predicted fracture pattern as well as the stress-strain curve for each structure. It is shown that structures based on spherical holes distributions lead to stiffer structures in tensile and shear conditions. The distribution of cavities has a strong influence on the mechanical behaviour. The square distribution improves stiffness, while the hexagonal distribution improves the shear modulus. Random distributions clearly decrease the stiffness and strength of the structure, although the damage in these structures is more progressive. Therefore, this work provides a comparative study to assess the influence of the lattice topological structure on some mechanical properties of interest in structural engineering, as a function of porosity., The authors gratefully acknowledge the funding support received from the Spanish Ministry of Economy and Competitiveness and the FEDER operation program for funding the projects DPI2017-89197-C2-1-R and DPI2017-89197-C2-2-R
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A New Cutting Device Design to Study the Orthogonal Cutting of CFRP Laminates at Different Cutting Speeds

  • Criado, V.
  • Cantero Guisández, J.L.
  • Díaz-Álvarez, J.
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
[EN] Carbon Fiber-reinforced plastics (CFRPs) are widely used in the aerospace industry due to their highly mechanical properties and low density. Most of these materials are used in high-risk structures, where the damage caused by machining must be controlled and minimized. The optimization of these processes is still a challenge in the industry. In this work, a special cutting device, which allows for orthogonal cutting tests, with a linear displacement at a wide range of constant cutting speeds, has been developed by the authors. This paper describes the developed cutting device and its application to analyze the influence of tool geometry and cutting parameters on the material damage caused by the orthogonal cutting of a thick multidirectional CFRP laminate. The results show that a more robust geometry (higher cutting edge radius and lower rake angle) and higher feed cause an increase in the thrust force of a cutting tool, causing burrs and delamination damage. By reducing the cutting speed, the components with a higher machining force were also observed to have less surface integrity control., This research was funded by the Ministry of economy, Industry and Competitiveness and FEDER (grant number: DPI2017-89197-C2-1-R).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the effect of geometrical fiber arrangement on damage initiation in CFRPs under transverse tension and compression

  • Marco, Miguel
  • Miguélez, María Henar
  • González, David
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] The mechanical performance of composite materials is strongly dependent on its microstructure. Efficient design of composites requires proper estimation of the effect of the microstructure on residual stresses that arising from cooling due to manufacturing temperature. The study of the stresses and damage in fibres interface and its relationship with geometrical distribution of the fibres can contribute to a better comprehension of the mechanical response of the composite. We use 2D numerical models to represent a composite material reinforced with longitudinal fibres. The mechanical behaviour is analysed taking into account the cooling effect and tension/compression transverse loading. We have generated a range of virtual microstructures, characterized by the microstructure randomness, to study the influence of the fiber randomness on the damage initiation. Damage initiation at fibres interfaces has been estimated from the stresses induced at the interface, both in the whole structure and for individual fibers. As expected, a strong effect of the randomness of the fiber arrangement on the damage initiation has been found. For all microstructures and loading modes, higher values of microstructure randomness results in earlier damage development. Normal and shear stresses at individual fibre interfaces have been analysed under tension and compression loading. In tension, normal stress at the fiber interface fully dominates the interfacial damage initiation. In compression, damage is almost completely dominated by the interfacial tangential stress. In compression, localized plasticity develops simultaneously with damage initiation whereas in tension, damage initiation occurs at a stress three times lower than the required for the onset of plasticity. The maximum shear and normal stresses around individual fibers are strongly affected by the local neighborhood., The authors gratefully acknowledge the funding support received from the Spanish Ministerio de Ciencia e Innovacion and the FEDERoperation program for funding the projects DPI2017-89197-C2-1-R and DPI2017-89197-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

An Experimental and Numerical Investigation to Characterize an Aerospace Composite Material with Open-Hole Using Non-Destructive Techniques

  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Belda Ricardo|||0000-0003-3913-5773
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] In this study, the open-hole quasi-static tensile and fatigue loading behavior of a multidirectional CFRP thick laminate, representative of laminates used in the aerospace industry, is studied. Non-destructive techniques such as infrared thermographic (IRT) and digital image correlation (DIC) are used to analyze the behavior of this material. We aim at characterizing the influence of the manufacturing defects and the stress concentrator through the temperature variation and strain distribution during fatigue and quasi-static tests. On the one hand, the fatigue specimens were tested in two main perpendicular directions of the laminate. The results revealed that manufacturing defects such as fiber waviness can have a major impact than open-hole stress concentrator on raising the material temperature and causing fracture. In addition, the number of plies with fibers oriented in the load direction can drastically reduce the temperature increment in the laminate. On the other hand, the quasi-static tensile tests showed that the strain distribution around the hole is able to predict the crack initiation and progression in the external plies. Finally, the experimental quasi-static tests were numerically simulated using the finite element method showing good agreement between the numerical and experimental results., This research was funded by the FEDER programme and the Spanish Ministerio de Ciencia, Innovacion y Universidades, projects DPI2017-89197-C2-1-R and DPI2017-89197-C2-2-R. The funding of the Generalitat Valenciana, Programme PROMETEO 2016/007 is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

El fenómeno de cut-out en fractura intertrocantérica de fémur: análisis mediante modelo de elementos finitos, The cut-out phenomenon in intertrochanteric femur fracture: analysis using a finite element model

  • Arias-Blanco, A.
  • Marco, M.
  • Miguélez, M.H.
  • Caeiro-Rey, J.R.
  • Larraínzar-Garijo, R.
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] Objetive: This work aimed to analyze the cut-out phenomenon, which involves oblique displacements and/or rotations of the femoral head around the cephalic component of the intramedullary nail. The analysis was carried out using finite element numerical models. This technique seeks to understand the failure of this type of fixation and establish what positioning of the system favors or prevents failure due to cut-out. Material and methods: The study was carried out on a numerical model of the proximal limb of an artificial femur and an intramedullary nail type PFNA (proximal femoral nail anti-rotation). In the numerical model, the position of the intramedullary nail was varied in the anterior/posterior and superior/inferior directions to analyze the influence of the position on the cut-out phenomenon. Stresses in critical areas and torque on the nail under normal position loading were analyzed. Results: The most critical position was the one in which the intramedullary nail is placed in the superior position, due to the high compressions that appear in the trabecular bone of the femoral head. The centered position of the nail decreased the risk of bone damage and the torque that the intramedullary nail has to support. Conclusions: This type of model allows us to simulate the influence of the nail position and obtain variables that are otherwise difficult to analyze. Although it is a simple model with static load, it confirms that a centered position of the intramedullary nail reduces the risk of cut-out., [ES] Resumen Objetivo El objetivo del trabajo fue analizar el fenómeno de cut-out, fenómeno que supone desplazamientos oblicuos y/o rotaciones de la cabeza femoral alrededor del componente cefálico del clavo intramedular. El análisis se llevó a cabo mediante modelos numéricos de elementos finitos. Con esta técnica se busca entender el fallo de este tipo de fijaciones y establecer qué posicionamiento del sistema favorece o evita el fallo por cut-out. Material y métodos El estudio se realizó sobre un modelo numérico de la extremidad proximal de un fémur artificial y un clavo intramedular tipo PFNA (femoral proximal de antirrotación). En el modelo numérico se varió la posición del clavo intramedular en dirección anterior/posterior y superior/inferior para analizar la influencia de la posición en el fenómeno de cut-out. Se analizaron las tensiones en zonas críticas y par torsor sobre el clavo bajo una carga en posición normal. Resultados La posición más crítica fue aquella en la que el clavo intramedular está colocado en la posición superior, debido a las altas compresiones que aparecen en el hueso trabecular de la cabeza femoral. La posición centrada del clavo disminuyó el riesgo de daño óseo y el par torsor que tiene que soportar el clavo intramedular. Conclusión Este tipo de modelos permite simular la influencia de la posición del clavo y obtener variables que de otra manera son difíciles de analizar. Aunque se trata de un modelo sencillo con carga estática, confirma que una posición centrada del clavo intramedular disminuye el riesgo de cut-out., The authors are grateful for the funding received through the 2018 Spanish Society for Bone Research and Mineral Metabolism research grant. They also appreciate the Ministry of Science and Innovation funding and the ERDF Program through the projects DPI2017-89197-C2-1-R and DPI2017-89197-C2-2-R.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The minimum shear stress range criterion and its application to crack orientation prediction in incomplete contact fretting problems

  • Infante, Diego
  • Llavori, I.
  • Zabala, A.
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] A proper prediction of crack paths is required when assessing accurately the fatigue crack propagation life. Recently, some authors have pointed out that the criterion of minimum shear stress range leads to inconsistent results when predicting fretting crack paths under incomplete contacts. In this paper, different fretting experiments with cylinder-to-flat contact found in the literature are reviewed, and the corresponding crack path prediction using the extended finite element method and the minimum shear stress range crack orientation criterion is performed. Results show the applicability of the criterion to predict the crack orientation during stage II in incomplete contact fretting problems., The authors gratefully acknowledge the financial support given by the Spanish Ministry of Economy and Competitiveness and the FEDER program through the project DPI2017-89197-C2-1-R, DPI2017-89197-C2-2-R and DPI2014-56137-C2-2-R and the FPI subprogram associated to the project with the reference BES-2015-072070. The support of the Generalitat Valenciana, Programme PROMETEO 2016/007, is also acknowledged. The financial support given by the Eusko Jaurlaritza under "Programa de apoyo a la investigacion colaborativa en areas estrategicas" (Project MEDECA: Ref. KK-2017/00053, and MEDECA2: Ref. KK-2018/00013) programs is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the use of the Theory of Critical Distances with mesh control for fretting fatigue lifetime assessment

  • Zabala, A.
  • Infante-Garcia, D.
  • Goel, S.
  • Endrino, J. L.
  • Llavori, I.
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] This work analyses the viability of the theory of critical distances (TCD) using mesh control for fretting fatigue lifetime assessment. More than seven hundred sets of simulations were performed by taking seventy different experimental tests reported previously in the literature. The outcome of the present study suggests that the TCD mesh control method can be extended to fretting fatigue problems by the reasonable assumption of setting the right element size proportional to critical distance. In this study, a significant computational time reduction of up to 97% was obtained. Thus, this study provides a simple method to design complex 3D industrial components subjected to fretting fatigue phenomena using finite element analysis efficiently without requiring complex remeshing techniques, Surface Technologies Research Group at Mondragon University gratefully acknowledge the financial support given by the Eusko Jaurlaritza under the "Programa de apoyo a la investigacion colaborativa en areas estrategicas" (Project MULTIMAT+: Ref. KK-2019/00067) program. The financial support given by the Spanish Ministerio de Ciencia, Innovacion y Universidades and the FEDER program through the projects DPI2017-89197-C2-1-R, DPI2017-89197-C2-2-R and the FPI subprogram with the reference BES-2015-072070. The support of the Generalitat Valenciana, Programme PROMETEO 2016/007, is also acknowledged. SG and JLE acknowledges the support of the "Centre for Doctoral Training in Ultra-Precision" at Cranfield University (EP/L016567/1). We would like to acknowledge the support from the Isambard Bristol, UK supercomputing service extended via the Resource Allocation Panel (RAP) grant and financial help from other grants such as RCUK (Grant No. EP/S013652/1 and EP/S036180/1), Cost Actions (CA15102 and CA18125) from H2020 and Royal Academy of Engineering (Grant No. IAPP18-19\295). JLE would like to acknowledge the Department of Economic Development and Infrastructure of the Basque Country (Elkartek Program, KK-2019/00062)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the effect of out-of-phase biaxial fatigue loads on crack paths in cruciform specimens using XFEM

  • Infante, Diego
  • Qian, Guian
  • Miguélez, María Henar
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] In the present research work, a numerical crack growth analysis using linear elastic fracture mechanics is carried out paying attention to the crack paths that grow in the central part of cruciform specimens under biaxial fatigue loads. The crack propagation in this type of specimens has been studied using the extended finite element method (XFEM). The objective is to analyse the effect of different phase angles under biaxial fatigue loads and to assess the different orientation criteria for nonproportional loading, benefiting from the advantages of XFEM. The crack path and the stress intensity factor range of a crack either aligned or inclined to the load directions have been investigated using different crack orientation criteria. Symmetrical branching is predicted for an initial crack inclined at 45 degrees with phase angle of loading equal to 90 degrees and 180 degrees. Numerical results are in good agreement with the experimental observations found in the literature, although the study reveals important differences in the crack path predictions depending on the orientation criteria., The authors gratefully acknowledge the financial support given by the Spanish Ministry of Economy and Competitiveness and the FEDER program through the project DPI2017-89197-C2-1-R, DPI2017-89197-C2-2-R and DPI2014-56137-C2-2-11 and the FPI subprogram associated to the project with the reference BES-2015-072070. The support of the Generalitat Valenciana, Programme PROMETEO 2016/007, is also acknowledged. Guian Qian is grateful for the financial support by the National Natural Science Foundation of China (No.11872364).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Drilling of biocomposite materials: Modelling and experimental validation

  • Diaz-Alvarez, A.
  • Diaz-Alvarez, J.
  • Santiuste, C.
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
[EN] Induced damage during biocomposites drilling is significantly different to that produced on composites based on synthetic reinforcement such as carbon or glass fibers. In composites reinforced with carbon or glass fibers, induced damage increases with feed rate, however damage was observed to decrease with feed rate in biocomposites reinforced with natural fibers. This work is focused on the explanation of this differences between biocomposites and traditional composites based on the effect of strain rate on the material behavior during machining. A FEM model has been developed in ABAQUS/Explicit to verify this hypothesis. This numerical model has been used to explain the differences found between traditional composites and biocomposites in the influence of the main drilling parameters on induced damage during drilling. Experimental tests were conducted to validate the model through the comparison between thrust forces and damage factor for two different drills geometries on Flax/PLA bio composites. The results indicate that the decrease of induced damage with feed rate is only predicted when the constitutive model accounts for experimental behavior observed in this type of composites. Additionally, the numerical model demonstrated the ability to reproduce the effect of the different cutting conditions (cutting speed, feed, thickness and drill geometry) observed during experimental tests on induced damage during drilling., Y Authors gratefully acknowledges the support of Spanish Ministry of Economy and FEDER program (EU) through the projects DPI2017-89197-C2-1-R and DPI2013-43994-R, and Madrid Regional Government under the project IND2017/IND7762
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A comparison between some fracture modelling approaches in 2D LEFM using finite elements

  • Marco, Miguel
  • Infante-García, Diego
  • Belda Ricardo|||0000-0003-3913-5773
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] The finite element method has been widely used to solve different problems in the field of fracture mechanics. In the last two decades, new methods have been developed to improve the accuracy of the solution in 2D linear elastic fracture mechanics problems, such as the extended finite element method (XFEM) or the phantom node method (PNM). The goal of this work is to quantify the differences between some numerical approaches: standard finite element method (FEM), mechanical property degradation, interelemental crack method with multi-point constraints, XFEM and PNM. We explain the different techniques analysed together with their advantages and disadvantages. We compare these numerical techniques to model fracture using problems of reference with known solutions, evaluating their behaviour in terms of convergence with respect to the element size and accuracy of the stress intensity factor (SIF), stresses ahead the crack tip and crack propagation prediction. Some of the new techniques have shown a better accuracy in SIF calculation or stress fields ahead the crack tip and other lead to high errors in local results estimations. However, all methods reviewed here can predict crack propagation for the problems of reference of this work, showing good accuracy in crack orientation prediction., The authors gratefully acknowledge the funding support received from the Spanish Ministerio de Ciencia, Innovacion y Universidades and the FEDER operation program in the framework of the projects DPI2017-89197-C2-1-R and DPI2017-89197-C2-2-R and the FPI subprograms BES-2014-068473 and BES-2015-072070. The financial support of the Generalitat Valenciana through the Programme PROMETEO 2016/007 is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the Role of Contact and System Stiffness in the Measurement of Principal Variables in Fretting Wear Testing

  • Infante-García, Diego
  • Marco, Miguel
  • Zabala, Alaitz
  • Abbasi, Farshad
  • Llavori, Iñigo
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] In this work, the role of the contact stiffness in the measurement of principal variables in fretting wear tests is assessed. Several fretting wear tribometers found in the literature, including one developed by the authors, are analysed and modelled using numerical methods. The results show the importance of the tribosystem stiffness and tangential contact stiffness in the displacement sensor calibration and in the correct numerical modelling of fretting wear tests, especially for flat-to-flat contact configuration. The study highlights that, in most cases, direct comparisons between fretting results with severe wear obtained with different tribometers cannot be performed if the contact stiffness is not properly considered during the development of the experiments., This research was funded by Eusko Jaurlaritza, grant number KK-2017/00053 KK-2018/00013, and KK-2020/00063. This research was funded by the Spanish Ministry of Economy and Competitiveness and the FEDER program through the projects DPI2017-89197-C2-1-R and DPI2017-89197-C2-2-R. The financial support of the Generalitat Valenciana, Programme PROMETEO 2016/007, is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of the Machinability of Carbon Fiber Composite Materials in Function of Tool Wear and Cutting Parameters Using the Artificial Neural Network Approach

  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Muñoz-Sánchez, A.
  • Diaz-Alvarez, A.
  • Loya, J.A.
[EN] Local delamination is the most undesirable damage associated with drilling carbon fiber reinforced composite materials (CFRPs). This defect reduces the structural integrity of the material, which affects the residual strength of the assembled components. A positive correlation between delamination extension and thrust force during the drilling process is reported in literature. The abrasive effect of the carbon fibers modifies the geometry of the fresh tool, which increases the thrust force and, in consequence, the induced damage in the workpiece. Using a control system based on an artificial neural network (ANN), an analysis of the influence of the tool wear in the thrust force during the drilling of CFRP laminate to reduce the damage is developed. The spindle speed, feed rate, and drill point angle are also included as input parameters of the study. The training and testing of the ANN model are carried out with experimental drilling tests using uncoated carbide helicoidal tools. The data were trained using error-back propagation-training algorithm (EBPTA). The use of the neural network rapidly provides results of the thrust force evolution in function of the tool wear and cutting parameters. The obtained results can be used by the industry as a guide to control the impact of the wear of the tool in the quality of the finished workpiece., The Ministry of Economy and Competitiveness of Spain, projects DPI2017-89197-C2-1-R and DPI2017-89197-C2-2-R] and the Ministry of Science, Innovation and Universities, grant number [FJCI-2017-34910], funded this research.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical modelling of hip fracture patterns in human femur

  • Marco, Miguel
  • Caeiro-Rey, Jose Ramon
  • Miguélez, María Henar
  • Larrainzar-Garijo, Ricardo
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] Background and Objective: Hip fracture morphology is an important factor determining the ulterior surgical repair and treatment, because of the dependence of the treatment on fracture morphology. Although numerical modelling can be a valuable tool for fracture prediction, the simulation of femur fracture is not simple due to the complexity of bone architecture and the numerical techniques required for simulation of crack propagation. Numerical models assuming homogeneous fracture mechanical properties commonly fail in the prediction of fracture patterns. This paper focuses on the prediction of femur fracture based on the development of a finite element model able to simulate the generation of long crack paths. Methods: The finite element model developed in this work demonstrates the capability of predicting fracture patterns under stance loading configuration, allowing the distinction between the main fracture paths: intracapsular and extracapsular fractures. It is worth noting the prediction of different fracture patterns for the same loading conditions, as observed during experimental tests. Results and conclusions: The internal distribution of bone mineral density and femur geometry strongly influences the femur fracture morphology and fracture load. Experimental fracture paths have been analysed by means of micro-computed tomography allowing the comparison of predicted and experimental crack surfaces, confirming the good accuracy of the numerical model., The authors are indebted to University Complutense of Madrid and to the radiological team of the Hospital Universitario Infanta Leonor for supporting the experimental work on human bones included in this paper. The micro-CTs were performed in the Micro-Computed Tomography laboratory at CENIEH facilities with the collaboration of CENIEH staff. The authors gratefully acknowledge the funding support received from the Spanish Ministry of Economy and Competitiveness and the FEDER operation program for funding the projects DPI2013-46641-R, DPI2017-89197-C2-1-R, DPI2017-89197-C2-2-R, RTC-2015-3887-8 and the Generalitat Valenciana through theproject Prometeo/2016/007. The authors also acknowledge the funding support received from the Fundacion Espanola de Investigacion Osea y del Metabolismo Mineral through the 2018 research fellowship program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Análisis de la progresión del daño en laminados compuestos con concentrador de tensiones bajo cargas de tracción

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Megías-Díaz, Raquel|||0000-0002-1698-7108
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[ES] En este trabajo se analiza el comportamiento de un laminado grueso de CFRP multidireccional típico de componentes aeroespaciales bajo cargas de tracción cuasiestática. Para realizar este estudio se utilizó la técnica no destructiva de correlación digital de imágenes (DIC). El objetivo es caracterizar la influencia de un concentrador de tensiones a través de la distribución de deformaciones durante los ensayos cuasiestáticos. Los ensayos de tracción mostraron que la distribución de deformaciones alrededor del agujero es capaz de predecir el inicio y la progresión de la grieta en las capas externas. Finalmente, las pruebas experimentales se simularon numéricamente mediante el método de elementos finitos, mostrando una buena concondarncia entre los resultados numéricos y experimentales, y obteniendo así información de las capas más internas., Los autores agradecen el material proporcionado por AIRBUS DEFENCE AND SPACE y al Ministerio de Economía y Competitividad de España por la financiación, dentro del marco del proyecto DPI2017-89197-C2-1-R y DPI2017-89197-C2-2-R y el subprograma asociado de ayudas FPI con referencia PRE2018-086277.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical analysis of the influence of micro-voids on fretting fatigue crack initiation lifetime

  • Infante-García, Diego
  • Miguélez, María Henar
  • Wahab, Magd Abdel
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] In this paper, the influence of the heterogeneity in the predicted crack initiation lifetime under fretting fatigue conditions is analysed for a regular and a random distribution of micro-voids. A critical plane analysis with two multiaxial damage criteria is performed to assess the crack initiation lifetime. The predicted initiation lifetime in the heterogeneous material is compared with the results obtained in the homogeneous case. The numerical results show that the heterogeneity has a noticeable influence on the predicted initiation lifetime. Furthermore, the numerical model suggests that a crack may firstly initiate at the upper edge of the micro-voids located close to the contact edge, leading to a mean reduction of the predicted crack initiation lifetime. However, in some cases, the introduction of micro-voids reduces the stress intensity at the contact edge and thus decreasing the predicted crack initiation lifetime., The authors gratefully acknowledge the financial support given by the Spanish Ministry of Economy and Competitiveness and the FEDER program through the projects DPI2017-89197-C2-1-R, DPI2017-89197-C2-2-R and the FPI subprogram with the reference BES-2015-072070. The support of the Generalitat Valenciana, Programme PROMETEO 2016/007, is also acknowledged.r The last author would like to acknowledge the financial support of the Research Foundation-Flanders (FWO), The Luxembourg National Research Fund (FNR) and Slovenian Research Agency (ARRS) in the framework of the FWO Lead Agency project: G018916N 'Multi-analysis of fretting fatigue using physical and virtual experiments'.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Relevant factors affecting the direction of crack propagation in complete contact problems under fretting fatigue

  • Marco, Miguel
  • Infante-Garcia, Diego
  • Diaz-Alvarez, Jose
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] In fatigue problems, an accurate estimation of the propagation direction is important for life prediction. We identify the most relevant factors that affect the crack orientation during the propagation stage of fretting fatigue cracks, arising from complete contacts. Contrary to what initially expected, parameters such as normal load, cyclic bulk load, etc. do not have a noticeable influence on the orientation. However the relative Young's moduli of indenter/specimen materials, the indenter width and the surface coefficient of friction are the most influencing factors. Analyses are performed through the extended finite element method (X-FEM) and an orientation criterion for non-proportional loading proposed by the authors. Experimental fretting fatigue tests confirm the predicted trends. An explanation of this behaviour is also given., The authors gratefully acknowledge the financial support given by the Spanish Ministry of Economy and Competitiveness and the FEDER program through the projects DPI2017-89197-C2-1-R and DPI2017-89197-C2-2-R. The support of the Generalitat Valenciana, Programme PROMETEO 2016/007, is also acknowledged. The authors thank the collaboration of Mr. Francisco Gelardo Rodriguez
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Modeling the delamination failure under compressive loads in CFRP laminates based on digital image correlation analysis

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[EN] Laminate composite materials such as CFRPs are highly susceptible to delamination, being one of the common failure modes in composite laminates. The combination of severe delamination with uniaxial compressive loads leads to the loss of stability and structure failure. In this study, the authors present an experimental and numerical analysis of this effect in laminates. A series of tests were carried out with four different specimens including delamination-free plates and plates with incipient delamination with different damage size and location. 3D Digital Imagen Correlation technique was applied to predict the buckling initiation and propagation and to validate the numerical models implemented, showing good agreement between the numerical and experimental results. Model material failure includes Hashin criterion and cohesive zone model (CZM) to predict delamination. Finally, numerical models have been used to predict the crack initiation and progression in the rest of samples., This research was funded by the FEDER programme and the Spanish Ministry of Science and Innovation, under projects DPI2017-89197-C2-1-R, DPI2017-89197-C2-2-R, PID2020-118480RB-C21, PID2020-118480RB-C22 and the associated predoctoral subprogram PRE2018-086277. The funding of the Generalitat Valenciana, Programme PROMETEO 2021/046 and project GV 2021/156, is also acknowledged.