Skip to main content

ENSAYO MECANICO DE LAMINADOS CON DEFECTOS Y SIMULACION NUMERICA

PID2020-118480RB-C21

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2020
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT POLITÈCNICA DE VALÈNCIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 22
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Visco-hyperelastic material model fitting to experimental stress-strain curves using a genetic algorithm and its application to soft tissue simulants

  • Gómez-Garraza, Samuel
  • de Santos, Raúl
  • Marco, Miguel
  • Infante-García, Diego|||0000-0001-6010-2031
[EN] Ballistic impacts on human thorax without penetration can produce severe injuries or even death of the carrier. Soft tissue finite element models must capture the non-linear elasticity and strain-rate dependence to accurately estimate the dynamic human mechanical response. The objective of this work is the calibration of a visco-hyperelastic model for soft tissue simulants. Material model parameters have been calculated by fitting experimental stress-strain relations obtained from the literature using genetic algorithms. Several parametric analyses have been carried out during the definition of the optimization algorithm. In this way, we were able to study different optimization strategies to improve the convergence and accuracy of the final result. Finally, the genetic algorithm has been applied to calibrate two different soft tissue simulants: ballistic gelatin and styrene-ethylene-butylene-styrene. The algorithm is able to calculate the constants for visco-hyperelastic constitutive equations with high accuracy. Regarding synthetic stress-strain curves, a short computational time has been shown when using the semi-free strategy, leading to high precision results in stress-strain curves. The algorithm developed in this work, whose code is included as supplementary material for the reader use, can be applied to calibrate visco-hyperelastic parameters from stress-strain relations under different strain rates. The semi-free relaxation time strategy has shown to obtain more accurate results and shorter convergence times than the other strategies studied. It has been also shown that the understanding of the constitutive models and the complexity of the stress-strain objective curves is crucial for the accuracy of the method., This work was supported by the Madrid Community (Spain) (IND2020/IND-17413); Generalitat Valenciana and European Social Fund (CIAPOS/2021/271); and Universitat Politecnica de Valencia (PAID-PD-22); MCIN/AEI/https://doi.org/10.13039/501100011033 and the European Union "NextGenerationEU"/PRTR" (PID2020-118480RB-C21, PDC2021-121368-C22). The authors also acknowledge to the Ministry of Culture and Sport (Spain) and European Union-Next Generation EU, the financial support through the project "Gemelos digitales para el diseno biomecanico avanzado de protecciones de cabeza en deportes con riesgo de impacto" (EXP_75127, Universidad Carlos III de Madrid). DAS:The datasets used and/or analysed during the current study are available from the corresponding author on reasonable request.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Estimation of the in-plane ultimate stress of lamellar tissue as a function of bone mineral density and osteocyte lacunae porosity

  • Vercher Martínez, Ana|||0000-0003-3695-6461
  • Megías-Díaz, Raquel|||0000-0002-1698-7108
  • Belda Ricardo|||0000-0003-3913-5773
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Vargas, Pablo
[EN] Detailed finite element models based on medical images (𝜇-CT) are commonly used to analyze the mechanical behavior of bone at microscale. In order to simulate the tissue failure onset, isotropic failure criteria of lamellar tissue are often used, despite its non-isotropic and heterogeneous nature. The main goal of the present work is to estimate the in-plane ultimate stress of lamellar bone, considering the influence of mineral content and the porosity due to the osteocyte lacunae concentration. To this aim, a representative volume cell of lamellar tissue is modeled numerically, including: (1) non-isotropic elastic properties of tissue as a function of the bone mineral density and (2) explicit modeling of the osteocyte lacunae, considering the range of porosity content, size and orientation of ellipsoid-shaped lacunae. Firstly, the element size for the finite element models have been defined from a preliminary convergence analysis. Bounds on the ultimate stress of non-porous lamellar tissue are estimated for two values of bone mineral density, considering the results of tensile and compressive tests of wet osteons from the literature. Subsequently, the ultimate stress of lamellar tissue considering several values of micro-porosity is addressed. Results: Results obtained in this work show that the strength of lamellar bone decreases exponentially with the increase of lacunae porosity concentration. Ultimate stress of non-porous tissue (𝑝 = 0%) increases with high mineral content, reaching a value of ̄ 𝑆 𝑐 𝑡𝑟𝑎𝑛𝑠 = 355.40 ± 39.80 MPa for compression in the transversal direction of the fiber bundles, being BMD = 1.246 g/cm3. The mean value for the longitudinal to transverse strength ratio evaluated for porosity 𝑝 = 0%, 1% and 5% and a mineral content BMD = 1.2 g/cm3, is 2.47:1 for tension and 1.55:1 for compression. These values are in agreement with literature. Conclusions: Osteocyte lacunae act as stress concentrators, acting as potential stimulus for the bone regeneration process. A novel micromechanical model for the in-plane ultimate stress of lamellar tissue as a function of mineral content and lacunae concentration is presented. Additional considerations about the intralamellar shear stress evolution are also given, The authors acknowledge the Ministerio de Ciencia e Innovación y Universidades and the European Regional Development Fund (FEDER) for the financial support received through the projects PID2020- 118920RB-I00 and PID2020-118480RB-C21 and C22 funded by MCIN/AEI/10.13039/501100011033 and by ERDF A way of making Europe , the Ministerio de Ciencia e Innovación y Universidades MCIN/AEI/ 10.13039/501100011033 and Europe Union NextGenerationEU/PRTR for the projects PDC2021-121368-C21 and C22, and the Generalitat Valenciana for Programa PROMETEO/2021/046
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Rapid fatigue life estimation of drilled CFRP laminates and titanium stacks using thermography

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[EN] In this work, we estimate the fatigue life of drilled Carbon Fiber Reinforced Polymer (CFRP) laminates making use of the temperature evolution of the component. As the self-heating effect due to cyclic loading causes a temperature change in the initial stages of the loading, the slope of the temperature variation ¿T versus the number of cycles can be used to estimate the remaining life. We have validated the applicability of the procedure for drilled laminates under different cutting conditions, and for drilled Ti-CFRP stacks. Infrared thermography was used to obtain the temperature variation during cycling loading. The results proved that the obtained adjusted model can effectively estimate the fatigue life of CFRP laminates with delamination damage or thermal damage with an error of 15%, proving the usefulness of this methodology for drilled and stacked laminates., This research is part of the R + D + i project PID2020-118480RBC21,-C22, and PID2023-151610OB-C21,-C22, funded by MCIN/AEI/ 10.13039/501100011033 and by ERDF A way of making Europe . Grant PRE2018-086277 funded by MCIN/AEI/10.13039/ 501100011033 and by ESF Investing in your future . The funding of the Generalitat Valenciana, Programme PROMETEO 2021/046 and project GV/2021/060 is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the use of the theory of critical distances with mesh control for fretting fatigue life assessment in complete and nearly complete contacts

  • Infante-García, Diego|||0000-0001-6010-2031
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Zabala, A.
  • Llavori, I.
[EN] In this work, the theory of critical distances using point method and mesh control approach for fretting fatigue life prediction in complete and nearly complete contacts is analysed. The approach is applied to thirty experi-mental tests found in the literature, where almost nine hundred simulations are carried out. The work concludes that the theory of critical distances using mesh control is able to predict the fretting fatigue strength of com-ponents using an optimum mesh size of 1.6 times the critical distance for all contact configurations analysed. Due to the use of an element size of around the critical distance length, the computational cost can be reduced up to 98% in comparison with the traditional theory of critical distances., This research was funded by the FEDER programme and the Spanish Ministry of Science and Innovation, under project PID2020-118480RB-C21/AEI/10.13039/501100011033. The funding of the Generalitat Valenciana, Programme PROMETEO 2021/046 and Universitat Politecnica de Valencia, Programme PAID-10-21 is also acknowledged. The authors also gratefully acknowledge the financial support given the Eusko Jaurlaritza under "Programa de apoyo a la investigacion colaborativa enareas estrategicas" (Project BISUM: Ref. KK-2021/00089) programs.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The role of the interfaces and cross-links on the mechanical behavior of mineralized collagen fibrils. A numerical approach

  • Vercher Martínez, Ana|||0000-0003-3695-6461
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Fuenmayor Fernández, Francisco-Javier|||0000-0003-3594-9593
  • García-Aznar, J. Manuel
[EN] Mechanical properties of bone tissue are highly dependent on its hierarchical structure. The presence of microcracks and diffuse damage in lamellar bone is correlated with the failure of the collagen-mineral interface in mineralized collagen fibrils (MCF). The main goal of this work is to evaluate the mechanical behavior of the interfaces and quantify the stiffness loss of the MCF associated with different failure mechanisms, under controlled in-plane displacement. Additionally, we aim to study the role of the cross-links on the fibril mechanical response, beyond the interface failure. Inter- and intra-microfibrilar cross-links are analyzed. In order to address the first issue, a detailed representative volume of the MCF is analyzed by means of the finite element method, under the assumption of plane strain and periodic boundary conditions. In this model the interfaces between constituents are modeled with an exponential cohesive law. Enzymatic cross-links, located at the molecular terminals connecting each 4D (D = 67 nm) staggered molecules, are represented by non-linear springs. Three in-plane controlled deformations are applied. The results of this work provide the anisotropic stiffness loss of the tissue involved in the different failure mechanisms at the nano-scale length. The initiation of microcracks and the presence of damage zones are compatible with the failure mechanisms observed at interfaces. Interface failure entails a progressive stiffness loss, bringing a non-linear behavior of bone. The strength obtained for the longitudinal maximum deformation is more than 20 times the transverse strength and 3.5 times the shear strength. The quantification of the reduction percentage in the elastic moduli and the shear stiffness when the fibril is damaged, has a potential application in improving failure criteria based on degradation of elastic constants. When longitudinal elongation is applied, the mechanical contribution of the cross-links in delaying the failure initiation of the interface is shown. Likewise, results of this work confirm the scarce influence of the cross-links in the strain range analyzed. Additionally, a threedimensional numerical model of several microfibrils is defined with the aim of analyzing the mechanical relevance of inter- and intra-microfibrilar cross-links, beyond the interface failure. Results confirm that cross-links transfer the load when strain increases, being highlighted the mechanical competence of the trivalent cross-links., The authors acknowledge the Ministerio de Ciencia e Innovacion y Universidades and the European Regional Development Fund (FEDER) for the financial support received through the projects PID2020-118920RB-I00, PID2020-118480RB-C21 and C22 funded by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe", the Ministerio de Ciencia e Innovacion y Universidades MCIN/AEI/10.13039/501100011033 and Europe Union Next Generation EU/PRTR for the projects PDC2021-121368-C21 and C22, CRUE-Universitat Politecnica de Valencia and the Generalitat Valenciana for Programa PROMETEO/2021/046.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Influencia de la morfometría y las propiedades aparentes en la integridad estructural del hueso trabecular humano enfermo y sano

  • Megías-Díaz, Raquel|||0000-0002-1698-7108
  • Belda Ricardo|||0000-0003-3913-5773
  • Vercher Martínez, Ana|||0000-0003-3695-6461
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[ES] En este trabajo, se han estudiado las relaciones entre la morfometría y la respuesta mecánica de hueso trabecular humano. Las muestras analizadas proceden de cabezas femorales humanas y están divididas en tres grupos: grupo sano (GS), grupo artrósico (GA) y grupo osteoporótico (GO). Las muestras se han escaneado mediante micro-CT para disponer de la geometría y poder realizar el estudio morfométrico de la microarquitectura trabecular. Se han llevado a cabo ensayos de compresión cuasiestática en la dirección más rígida de las muestras hasta producir su fractura. La influencia entre los parámetros se ha estudiado mediante correlaciones lineales por grupos de forma independiente, ya que el comportamiento aparente es tan diferente entre las muestras que las relaciones obtenidas analizando todas las muestras en conjunto no son relevantes y presentan unos coeficientes de correlación muy bajos. El grupo sano (GS) es el que presenta relaciones relevantes (con un p-valor < 0.05) con la densidad de conectividad Conn.D, el número de trabéculas Tb.N, el área superficial de hueso BS y la dimensión fractal D. Además, también se han relacionado los parámetros aparentes obtenidos de los ensayos experimentales entre sí. Para el caso de GS, presenta correlación entre la tensión de fallo final ¿¿ y el módulo de Young aparente ¿¿¿¿. Respecto al grupo osteoporótico, tanto ¿¿ como ¿¿¿¿ presentan correlaciones con la separación trabecular Tb.Sp y el número de trabéculas Tb.N. Además, también presentan correlación ¿¿¿¿ y la deformación asociada a la que se da la tensión de fallo final ¿¿. El grupo artrósico (GA) es el que menos correlaciones presenta, únicamente entre ¿¿ y el volumen total de las muestras TV y entre ¿¿ y ¿¿¿¿. Las correlaciones lineales obtenidas indican que se podría determinar el módulo de Young aparente o la tensión máxima que soportan las muestras sin realizar los ensayos experimentales mediante la evaluación de imágenes micro-CT., Los autores desean agradecer la financiación recibidadesde la GVA por el programa PROMETEO 2021/046, y por los proyectos PID2020-118920RB-I00 y PID2020-118480RB-C21 y C22, financiado por MCIN/AEI/10.13039/5011000110 33 y por FEDER Una manera de hacer Europa y el proyecto PDC2021- 121368-C21 y C22 financiado por MCIN/AEI/10.13039/501100011033 y por la Unión Europea NextGenerationEU/PRTR .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of material extrusion parameters on fracture mechanisms of polylactic acid under three-point bending

  • Álvarez-Blanco, Mario
  • Arias-Blanco, Adrián
  • Marco, Miguel
  • Miguélez, María Henar
  • Infante-García, Diego|||0000-0001-6010-2031
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] In this work, a thorough fracture assessment of additive manufactured specimens made by 3D printed polylactic acid (PLA) under three-point bending is presented. This polymer is widely used in additive manufacturing for numerous applications, gaining prominence in fields such as biomechanics. Prismatic fully dense specimens and lattice structure specimens with different raster orientations and densities were fabricated using the material extrusion-based additive manufacturing technique. The objective is to analyse the effect of relevant process parameters on the fracture mechanism of short beam specimens tested under three-point bending. Digital image correlation and computed tomography have been used to measure the full field displacement and internal defects, respectively. Furthermore, the theory of critical distances was applied to assess the mechanical strength of lattice structure specimens. The results have shown the strong influence of raster orientation on the mechanical strength and fracture patterns even for negative air gap values. The transition from brittle to ductile failure was observed when changing density and raster orientation. Lastly, neck-shaped defects were detected in knots of specimens manufactured with a grid pattern. Defects in grid pattern specimens appear due to the prescribed path followed by the extruder during the building process. They were the main source causing a decrease in the mechanical strength and fracture trajectories. The objective of this research is to enhance the knowledge on the mechanical response of 3D printed components and to give an in-depth failure assessment., The authors gratefully acknowledge the funding support received from the Spanish Ministerio de Ciencia e Innovacion for funding the projects PID2020-112628RA-I00 and PID2020-118480RB-C21, -C22, MCIN/AEI / 10.13039/501100011033 and by "ERDF A way of making Europe"; project PDC2021-121368-C21 and C22 funded by MCIN/AEI/ 10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". The authors also thank the funding received from Madrid Community (Spain) through the project IND2020/IND-17413. The financial support of Generalitat Valenciana and European Social Fund through Programme PROMETEO 2021/046 and CIAPOS/2021/271 is also acknowledged. Lastly, the Universitat Politecnica de Valencia is acknowledged for the financial support through PAID-PD-22.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of bone surrogates by material extrusion-based additive manufacturing to mimic flexural mechanical behaviour and fracture prediction via phase-field approach

  • Álvarez-Blanco, Mario
  • Marco, Miguel
  • Miguélez, M. Henar
  • Infante-García, Diego|||0000-0001-6010-2031
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] Background and objective: The limited availability of human bone samples for investigation leads to the demand for alternatives. Bone surrogates are crucial in promoting research on the intricate mechanics of osseous tissue. However, solutions are restricted to commercial brands, which frequently fail to faithfully replicate the mechanical response of bone, or oversimplified customised simulants designed for a specific application. The manufacturing and assessment of reliable bone surrogates made of polylactic acid via material extrusion-based additive manufacturing are presented in this work. Methods: An experimental and numerical study with 3D-printed dog -bone and prismatic specimens was carried out to characterise the polymeric feedstock and analyse the influence of process parameters under three-point bending and quasi-static conditions. Besides, three porcine rib samples were considered as a reference for the development of the artificial bones. Bone surrogates were manufactured from the 3D-scanned real bone geometries. In order to reproduce the trabecular and cortical bone, a lattice structure for the infill and a compact shell surrounding the core were employed. Infill density and shell thickness were evaluated through different printing configurations. Additionally, a computational analysis based on the phase-field approach was conducted to simulate the experimental tests and predict fracture. The modelling considered homogenisation of the infill material. Results: Outcomes demonstrated the potential of the presented methodology. Maximum force and flexural stiffness were compared to real bone properties to find the optimal printing configuration, replicating the flexural mechanical behaviour of bone tissue. Certain configurations accurately reproduce the studied properties. Regarding the numerical model, strength and stiffness prediction was validated with experimental results. Conclusions: The presented methodology enables the manufacturing of artificial bones with accurate geometries and tailored mechanical properties. Furthermore, the described modelling strategy offers a powerful tool for designing bone surrogates., The authors gratefully acknowledge the funding support received from the Spanish Ministerio de Ciencia e Innovacion for funding the projects PID2020-112628RA-I00, PID2020-118480RB-C21 and C22, funded by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe", and the funding received from the Madrid Community (Spain) through the project IND2020/IND-17413. The authors are also grateful for the funding received from Generalitat Valenciana and European Social Fund programmes PROMETEO/2021/046 and CIAPOS/2021/271, and to Universitat Politecnica de Valencia for the grant PAID-PD-22.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental and numerical analysis of the influence of intramedullary nail position on the cut-out phenomenon

  • Arias-Blanco, A.
  • Marco, M.
  • Larraínzar-Garijo, R.
  • Miguélez, M. H.
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[EN] Background and objective: Proximal femur fractures, colloquially known as hip fractures, are a common pathology with increasing incidence in the last years due to the enhanced ageing population. Regarding the extracapsular fracture, the treatment for this pathology consists of a fixation of the fragments using an osteosynthesis device, mainly the intramedullary nail. This repairing method implies several complications, which may include the failure of the fixation device, frequently occurring due to the "cut-out" mechanism. The present work focuses on the study of how the position of the cephalic screw, which should be fixed during surgery, affects the cut-out risk. Through experimental tests and numerical models some variables that can be critical for the cut-out phenomenon are analysed. Methods: This study has been carried out through a numerical model based on the finite element method and experimental tests. The digital image correlation technique has been used in experimental tests to measure displacements on the femoral surface with the objective of numerical model validation. Some basic daily activities with different intramedullary nail positions have been analysed through the numerical model, considering variables that can induce the cut-out complication. Results: The results show how the intramedullary nail position clearly influences the cut-out risk, showing that displacements in the upper, anterior and posterior direction increase the cut-out risk, while displacement in the lower direction endangers the intramedullary nail itself. Thus, the centred position is the one which reduces the cut-out risk. Conclusions: This work supposes an improvement in the knowledge of the cut-out phenomenon thanks to the combination of experimental testing and validated numerical models. The effects of different intramedullary nail positions in the femoral head are studied, including a novelty variable as torque, which is critical for the structural integrity of the fixation. The main conclusion of the work is the determination of the central intramedullary nail position as the most favourable one for decreasing the cut-out risk., The authors gratefully acknowledge the funding support received from the Spanish Ministry of Science and Innovation for funding project PID2020-112628RA-I00/AEI/10.13039/501100011033, projects PID2020-118480RB-C21 and -C22 and from the Madrid Community (Spain) through the project IND2020/IND-17413. The financial support of the European Union NextGenerationEU/PRTR through grant number PDC2021-121368-C21 and -C22 and the Generalitat Valenciana through Programme PROMETEO 2021/046 is also acknowledged.& nbsp;
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Experimental and numerical analyses of the interaction between rigid non-penetrating projectiles, soft and hard tissue simulants and composite ballistic protection

  • Gómez-Garraza, Samuel
  • Álvarez-Blanco, Mario
  • Miguélez, Beatriz
  • Loya, José Antonio
  • Marco, Miguel
  • Infante-García, Diego|||0000-0001-6010-2031
[EN] The study of ballistic personal protections often only focuses on the mechanical response and ballistic limits of the armor considered. However, understanding the armor-carrier interaction under dynamic conditions remains underexplored. This research analyzes non-penetrating ballistic impacts on gelatin samples involving multi-ply composite ballistic protection panels, focusing on biomechanical damage. For this purpose, ballistic gelatin is presented as a reliable soft tissue simulant and thoroughly examined under non-penetrating ballistic impact conditions. The methodology includes two experimental approaches: (1) lowvelocity impact tests using rigid projectiles to isolate gelatin's mechanical behavior and (2) high-velocity impact tests with steel spherical projectiles, involving additionally ballistic protection panels and a simplified bone surrogate as a hard tissue simulant. Due to the complexity of experimentally assessing the dynamic interaction between soft and hard tissue simulants, protection, and projectiles, an explicit finite element model has been developed. These simulations incorporate different damage models in composite protection and bone surrogate to accurately replicate the experimental tests. In addition, a proposed visco-hyperelastic constitutive model for ballistic gelatin is validated, generating a powerful predictive tool for evaluating ballistic protection and biomechanical damage. This work provides a comprehensive study of the behind armor blunt trauma and introduces an experimental methodology to quantify the mechanical response of ballistic gelatin and hard tissue simulants under nonpenetrating ballistic impacts. It addresses a key gap in modeling soft tissue simulants under high-energy conditions and validates the corresponding visco-hyperelastic constitutive model. Findings highlight the importance of considering hard tissue effects when evaluating composite protection performance, which has not been previously addressed in literature. This work proposes an alternative evaluation framework to the assessment of advanced armor and biomechanical phenomena estimation. We further provide a deeper biomechanical insight in comparison with existing standards, bridging the gap between multi-layered composite protection and the human biomechanical response., This work was supported by the Madrid Community, Spain [IND2020/IND-17413]; the Spanish Ministry of Culture and Sport and "European Union NextGenerationEU/PRTR" ["Gemelos digitales para el diseno biomecanico avanzado de protecciones de cabeza en deportes con riesgo de impacto" EXP_75127, Universidad Carlos III de Madrid]; the projects PID2023-151610OB-C22 and PID2020-118946RB-I00 funded by Spanish Ministry of Science, Innovation and Universities (MICIU/AEI/https://doi.org/10.13039/501100011033)and FEDER, UE and the "European Union NextGenerationEU/PRTR" [PID2020-118480RB-C21, PDC2021-121368-C22].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Aplicación de termografía infrarroja en la estimación de la vida a fatiga en laminados de CFRP taladrados.

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[ES] La aplicación de técnicas no destructivas para evaluar materiales compuestos sometidos a fatiga es un área de creciente interés entre la comunidad científica. Entre las técnicas disponibles, destaca el uso de la termografía infrarroja debido a su asequibilidad, simplicidad y resultados prometedores en investigaciones previas. En este estudio, se aplica la termografía infrarroja con el objetivo de obtener modelos predictivos capaces de estimar el límite de fatiga de laminados gruesos de CFRP (polímero reforzado con fibra de carbono) sometidos a cargas de tracción. Los ensayos experimentales conllevan la monitorización de la temperatura en laminados con características típicas de la industria aeroespacial, a través de una cámara termográfica. La campaña experimental implica la variación de los niveles de daño por taladrado y las cargas cíclicas de tracción. Con los datos obtenidos de la evolución de la temperatura durante la fase inicial de los ensayos de fatiga se obtienen modelos analíticos predictivos del límite de fatiga. Los resultados indican que el modelo propuesto es capaz de predecir de manera eficiente el límite de fatiga con una alta fiabilidad, mostrando una sólida correlación entre las predicciones y los resultados experimentales, por lo que este estudio subraya la utilidad de las técnicas termográficas para evaluar el daño y predecir el límite de fatiga de laminados CFRP en diversas condiciones de carga, Los autores agradecen la financiación a través de los siguientes proyectos: PID2020-118480RB-C21 y C22, financiado por MCIN/AEI/ 10.13039/501100011033 y por FEDER Una manera de hacer Europa ; proyecto PDC2021-121368-C21 y C22 financiado por MCIN/AEI/ 10.13039/501100011033 y por la Unión Europea NextGenerationEU/PRTR ; ayuda PRE2018-086277 financiada por MCIN/AEI/10.13039 /501100011033 y por FSE Invierte en tu futuro . También agradecen la financiación de la Generalitat Valenciana, programa PROMETEO 2021/046 y el proyecto GV/2021/060.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of machining parameters on fretting fatigue life of Inconel 718

  • Infante-García, Diego|||0000-0001-6010-2031
  • Belda Ricardo|||0000-0003-3913-5773
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Díaz-Álvarez, A.
  • Díaz-Álvarez, J.
  • Cantero, J.L.
  • Miguélez, M.H.
[EN] This work focuses on the analysis of the influence of different machining factors on the fretting fatigue behaviour of Inconel 718. Fretting fatigue tests using a flat-to-flat with rounded edges contact were carried out using specimens with different manufacturing process parameters. The results pointed out the high impact that machining parameters possess in the Inconel 718 fatigue lifetime. Tool wear has shown to be the most significant parameter. Residual stresses measured along the direction of fatigue load have proved to be a relevant indicator of the fretting fatigue behaviour. Lastly, surface roughness has been shown to possess a weaker influence., The authors gratefully acknowledge the funding support received from the Spanish Ministerio de Ciencia e Innovación and the FEDER operation program for funding the projects PID2020-118480RB-C22 and PID2020-118480RB-C21 and the Generalitat Valenciana (Programme PROMETEO 2021/046).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Estudio de la fractura a compresión de hueso trabecular sano, osteoporótico y artrósico procedente de cabezas femorales humanas

  • Megías-Díaz, Raquel|||0000-0002-1698-7108
  • Belda Ricardo|||0000-0003-3913-5773
  • Vercher Martínez, Ana|||0000-0003-3695-6461
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
[ES] En este trabajo se ha estudiado el comportamiento mecánico del hueso trabecular mediante ensayos experimentales de compresión y el desarrollo de modelos numéricos de elementos finitos. Las muestras proceden de cabezas femorales humanas y se agruparon en tres cohortes: grupo sano (GS), grupo osteoporótico (GO) y grupo artrósico (GA). Los especímenes se ensayaron en la dirección estimada de máxima rigidez y se sometieron a cargas de compresión cuasiestática hasta la fractura. La respuesta experimental permitió calibrar los modelos numéricos, estimando el módulo de Young del tejido óseo y las propiedades de fallo de las muestras. Los resultados muestran que el hueso sano soporta un 52% más de carga que el hueso osteoporótico, y que la deformación correspondiente a la tensión máxima es un 33% mayor en el GS que en el GO. Las muestras artrósicas presentan un comportamiento intermedio, más próximo al grupo osteoporótico que al sano, lo que indica que las patologías analizadas se asocian a menores niveles de carga y deformación frente al hueso sano. La calibración de los modelos numéricos proporciona valores similares de deformación de inicio de fallo y de fallo completo para las muestras patológicas, mientras que en las muestras sanas estos valores difieren. En consecuencia, la simulación de la fractura en hueso osteoporótico requiere considerar propiedades de fallo específicas, coherentes con un comportamiento más frágil que el del hueso sano. Finalmente, este trabajo permite cuantificar dichos parámetros e identifica como principal origen de las diferencias las características morfométricas propias de la microestructura del hueso trabecular no sano., Los autores desean agradecer la financiación recibida desde la GVA por el Plan FDEGENT 2018 GVA y por el programa PROMETEO 2021/046, y por los proyectos PID2020-118920RB-I00 y PID2020-118480RB-C21 y C22, financiado por MCIN/AEI/10.13039/501100011033 y por FEDER Una manera de hacer Europa y el proyecto PDC2021-121368-C21 y C22 financiado por MCIN/AEI/10.13039/501100011033 y por la Unión Europea NextGenerationEU/PRTR .
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical analysis of the influence of triply periodic minimal surface structures morphometry on the mechanical response

  • Belda Ricardo|||0000-0003-3913-5773
  • Megías-Díaz, Raquel|||0000-0002-1698-7108
  • Vercher Martínez, Ana|||0000-0003-3695-6461
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Marco, Miguel
[EN] Background and Objective: Design of bone scaffolds requires a combination of material and geometry to fulfil requirements of mechanical properties, porosity and pore size. Triply Periodic Minimal Surface (TPMS) structures have gained attention due to their similarities to cancellous bone. In this work, we aim at exploring relationships between morphometry and mechanical properties for TPMS configurations.Methods: Eight TPMS structures are defined considering six porosity levels and their morphometry is characterized. The stiffness matrix of each structure is assessed and related to morphometry through a statistical analysis.Results: An orthotropic mechanical behavior has been derived from the numerical homogenization. Prop-erties decay exponentially for decreasing volume fraction. Through volume fraction variation, TPMS me-chanical properties can be selected to match bone properties in a range of 0.2% to 70% of the bulk mate-rial properties.Conclusions: The comparison between cancellous bone and TPMS morphometry, considering a unit cell size of 1.5 mm, reveals that the configurations analyzed in this work match the requirements of volume fraction, mean thickness and pore size. However, the TPMS studied in this work differ from cancellous bone anisotropy. The results in this paper provide a framework to select the proper TPMS configuration and its geometry for patient-specific applications., This work was supported by the Spanish Ministerio de Ciencia e Innovacion MCIN/AEI/10.13039/501100011033 through grant numbers PID2020-118480RB-C21, PID2020-118920RB-I0 0 and PID2020-112628RA-I0 0, the European Union NextGenerationEU/PRTR through grant number PDC2021-121368-C22 and the Generalitat Valenciana (Programme PROMETEO 2021/046 and Plan FDGENT 2018 GVA).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Verification of strain energy splits of phase field fracture model using Westergaard&apos, s problem under mixed-mode loading

  • Infante-García, Diego|||0000-0001-6010-2031
  • Quiñonero-Moya, Antonio Ramón|||0000-0002-2370-7960
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Álvarez-Blanco, Mario
[EN] One challenge in verifying strain energy splits in phase field fracture models is the lack of reference problems with exact solutions in mixed-mode loading that could serve as benchmark problems. In this work, different strain energy splits used in the variational phase field model have been applied to the classical Westergaard's problem. In contrast to other benchmark problems used in the literature, the proposed problem not only includes the singular term as a boundary condition but also implicitly considers all terms. To the authors' knowledge, this is the first time in the literature that this reference problem has been used to rigorously verify the accuracy of different energy splits of the phase field model. Several critical factors such as the pre- crack definition, mesh size, mixed mode ratio and the length scale parameter have been analysed. A good correlation between the numerical estimations and the analytical predictions was found for some pre-crack definition approaches under mode I. However, we demonstrated that the compatible regularisation length scale and mesh size are significantly lower under mode II loading (i.e., when the crack kinks) than under mode I., The authors gratefully acknowledge the funding support received from Generalitat Valenciana and European Social Fund CIAPOS/2021/271 and Vice-Rectorate for Research of Universitat Politecnica de Valencia with the project " Primeros Proyectos de Investigacion" (PAID-06-23) . The authors also thank the financial support of the Spanish Ministerio de Ciencia e Innovacion MCIN/AEI/10.13039/501100011033 and "ERDF A way of making Europe" through grant number PID2020-118480RB-C21 and PID2023-151610OB-C22 the Generalitat Valenciana (Programme PROMETEO 2021/046) . Grant PRE2021-097626 funded by MCIN/AEI/10.13039/501100011033 and by "ESF Investing in your future".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Numerical modelling of cancellous bone damage using an orthotropic failure criterion and tissue elastic properties as a function of the mineral content and microporosity.

  • Megías-Díaz, Raquel|||0000-0002-1698-7108
  • Vercher Martínez, Ana|||0000-0003-3695-6461
  • Belda Ricardo|||0000-0003-3913-5773
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Fuenmayor Fernández, Francisco-Javier|||0000-0003-3594-9593
  • PERIS SERRA, JOSE LUIS
  • Larrainzar-Garijo, Ricardo
[EN] Background and objective : Elastic and strength properties of lamellar tissue are essential to analyze the mechanical behaviour of bone at the meso- or macro-scale. Although many effort s have been made to model the architecture of cancellous bone, in general, isotropic elastic constants are assumed for tissue modelling, neglecting its non-isotropic behaviour. Therefore, isotropic damage laws are often used to esti- mate the bone failure. The main goals of this work are: (1) to present a new model for the estimation of the elastic properties of lamellar tissue which includes the bone mineral density (BMD) and the micro- porosity, (2) to address the numerical modelling of cancellous bone damage using an orthotropic failure criterion and a discrete damage mechanics analysis, including the novel approach for the tissue elastic properties aforementioned. Methods : Numerical homogenization has been used to estimate the elastic properties of lamellar bone considering BMD and microporosity. Microcomputed Tomography ( ¿-CT) scans have been performed to obtain the micro-finite element ( ¿-FE) model of cancellous bone from a vertebra of swine. In this model, lamellar tissue is orientated by considering a unidirectional layer pattern being the mineralized colla- gen fibrils aligned with the most representative geometrical feature of the trabeculae network. We have considered the Hashin¿s failure criterion and the Material Property Degradation (MPDG) method for sim- ulating the onset and evolution of bone damage. Results: The terms of the stiffness matrix for lamellar tissue are derived as functions of the BMD and mi- croporosity at tissue scale. Results obtained for the apparent yield strain values agree with experimental values found in the literature. The influence of the damage parameters on the bone mechanics behaviour is also presented. Conclusions : Stiffness matrix of lamellar tissue depends on both BMD and microporosity. The new ap- proach presented in this work enables to analyze the influence of the BMD and porosity on the mechan- ical response of bone. Lamellar tissue orientation has to be considered in the mechanical analysis of the cancellous bone. An orthotropic failure criterion can be used to analyze the bone failure onset instead of isotropic criteria. The elastic property degradation method is an efficient procedure to analyze the failure propagation in a 3D numerical model., The authors acknowledge the Ministerio de Ciencia e Innovacion and the European Regional Development Fund (FEDER) for the financial support received through the projects PID2020-118920RB-I00 and PID2020-118480RB-C21, the Generalitat Valenciana for Plan FDGENT 2018 and Programme PROMETEO 2021/046.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of distributed out-of-plane waviness defects on the mechanical behavior of CFRP laminates

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Quiñonero-Moya, Antonio Ramón|||0000-0002-2370-7960
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[EN] One of the most common defects induced during manufacturing of laminates is out-of-plane fibre waviness. This defect significantly affects the mechanical behavior of the laminate and reduces fatigue life and the load capacity of the material. Therefore, it is important to understand the impact of fibre waviness on the performance of composite laminates. In this work, multiple out-of-plane waves have been introduced throughout a Carbon Fibre Reinforced Polymer (CFRP) laminate at different thickness positions. The specimens were tested under tensile loading and an analysis of the surface of the laminate has been carried out by means of Digital Image Correlation (DIC). The results obtained by DIC were able to predict the apparent strain of the laminate quite accurately, as well as locate up to seven undulations at different depths. It was proved that a laminate with multiple wrinkles has 16% less tensile load strength. The results were used to validate different Finite Element (FE) models of the laminate showing a good agreement. These simple models were able to predict the initiation and propagation of failure in both the matrix and the fibre., This research is part of the R + D + i project PID2020-118480RB-C21 and C22, funded by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe". Grant PDC2021-121368-C21 and C22 funded by MCIN/AEI/10.13039/501100011033 and by the "European Union NextGenerationEU/PRTR". Grant PRE2018-086277 and PRE2021-097626 funded by MCIN/AEI/10.13039/501100011033 and by "ESF Investing in your future". The funding of the Generalitat Valenciana, Programme PROMETEO 2021/046 and project GV/2021/060, is also acknowledged.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Analysis of osteoporosis effect on the mechanical behaviour and morphometry of human cancellous bone

  • Megías-Díaz, Raquel|||0000-0002-1698-7108
[ES] En esta tesis, el principal objetivo es analizar el efecto de la osteoporosis en el comportamiento mecánico del hueso trabecular. El comportamiento del hueso trabecular se ha abordado desde diferentes enfoques: ensayos experimentales, modelos de elementos finitos (EF) e imagen médica obtenida por micro-CT. El impacto de la osteoporosis se ha estudiado en distintas escalas. Se ha abordado un estudio a nivel de tejido lamelar del hueso trabecular para estimar las ecuaciones que nos permitan definir las propiedades elásticas y resistentes en función de la densidad mineral ósea y la porosidad del tejido. Estas ecuaciones inferidas en los modelos de EF permitirán estudiar el comportamiento del tejido óseo lamelar abarcando un amplio rango de porosidades y DMOs. Se ha realizado un estudio de la estructura trabecular y del tejido lamelar utilizando un estereomicroscopio y el FESEM. Al nivel del tejido lamelar, se ha podido observar la disposición de las lamelas en distintas localizaciones, como en las trabéculas y sus intersecciones. Además, se ha podido evaluar la porosidad tisular natural y la producida por enfermedades óseas. Esta información se ha introducido en los modelos EF para definir las propiedades en las muestras. Las ecuaciones elásticas y resistentes estimadas consideran un comportamiento ortótropo y es posible cuantificar cómo afectan la DMO y la porosidad a estas propiedades. Se ha estudiado el comportamiento mecánico a compresión de muestras humanas de hueso trabecular procedente de cabezas femorales. Estas muestras se clasifican en tres grupos: sano, artrósico y osteoporótico. Estas muestras se han estudiado mediante ensayos experimentales, imagen médica y modelos de EF, permitiendo obtener gran información sobre el comportamiento mecánico del hueso. La respuesta mecánica está muy influenciada por la microarquitectura trabecular. Los resultados obtenidos más relevantes son el módulo aparente, la tensión de fallo y la deformación de fallo. Se han podido generar modelos de EF y estudiar la morfometría de las muestras. Los modelos de EF han permitido estimar las propiedades a nivel de tejido: módulo de Young a nivel de tejido y las deformaciones de fluencia y fallo. Los resultados muestran que a nivel de tejido no se aprecian variaciones en el módulo de Young aunque el hueso presente una patología ósea. Un comportamiento de fluencia similar se ha observado para todos los grupos, con diferencias únicamente en la deformación de fallo. El estudio morfométrico permite analizar los parámetros morfométricos que diferencian las muestras sanas de las enfermas. Se han correlacionado dichos parámetros con la respuesta mecánica para analizar los que tienen mayor influencia sobre ella. Las correlaciones permiten estimar la respuesta mecánica del hueso utilizando imagen médica sin realizar ensayos experimentales. Los parámetros obtenidos de la respuesta mecánica también se han relacionado entre sí, permitiendo conocer el comportamiento de cada una de las muestras que es diferente según la enfermedad que padecen. También, se han estudiado muestras bioinspiradas y estructuras TPMS obtenidas mediante fabricación aditiva. Estas muestras se han fabricado con PLA como material de impresión. Las muestras muestran un comportamiento ortótropo como las muestras trabeculares. Los simulantes pueden ser utilizados para hacer estudios previos cuando no se disponga de las muestras óseas. El tratamiento de fracturas óseas de gran tamaño requiere de técnicas no convencionales para la fijación del hueso. Suelen utilizarse andamios óseos con triple periodicidad que tienen como resultado propiedades ortótropas iguales en las tres direcciones ortogonales. Estos sistemas deben disponer de rigideces similares al hueso alrededor del defecto para evitar el aflojamiento del implante. Por ello, se propone una metodología que permite diseñar andamios óseos paciente-específicos que permiten ajustar las propiedades mecánicas ortótropas en función del hueso., [CA] En esta tesi, el principal objectiu és analitzar l'efecte de l'osteoporosi en el comportament mecànic de l'os trabecular. El comportament de l'os trabecular s'ha abordat des de diferents plantejaments, com són els assajos experimentals, els models d'elements finits (EF) i la imatge mèdica obtinguda per micro-CT. L'impacte de l'osteoporosi s'ha estudiat en diferents escales. En primer lloc, s'ha abordat un estudi a nivell de teixit lamellar de l'os trabecular per a estimar les equacions que ens permeten definir les propietats elàstiques i resistents en funció de la densitat mineral òssia i la porositat del teixit. Estes equacions inferides en els models d'EF permetran estudiar el comportament del teixit ossi lamel·lar abastant un ampli rang de porositats i DMOs. S'ha realitzat un estudi de l'estructura trabecular i del teixit lamel·lar utilitzant un estereomicroscopi i el FESEM. Al nivell del teixit lamel·lar, s'ha pogut observar la disposició de les lamel·les en diferents localitzacions, com en les trabècules i les seues interseccions. A més, s'ha pogut avaluar la porositat tissular natural i la produïda per malalties òssies. Tota esta informació ha sigut incorporada als models numèrics per a poder definir les propietats en les mostres trabeculars. Les equacions elàstiques i resistents estimades consideren un comportament ortòtrop i és possible quantificar com afecten la DMO i la porositat a estes propietats. S'ha estudiat el comportament mecànic a compressió de mostres humanes d'os trabecular procedent de caps femorals i s'han classificat en tres grups: sa, artròsic i osteoporòtic. S'han estudiat mitjançant assajos experimentals, imatge médica i models d'EF, obtenint gran informació sobre el comportament mecànic de l'os. La resposta mecànica està fortament influenciada per la microarquitectura trabecular. Els resultats obtinguts més importants són el mòdul aparent, la tensió de fallada i la deformació de fallada. S'han generat models d'EF i estudiat la morfometria. Els models d'EF han permés estimar les propietats a nivell de teixit: el mòdul de Young a nivell de teixit i les deformacions de fluència i fallada. A nivell de teixit no s'aprecien variacions en el mòdul de Young encara que l'os present una patologia òssia. Un comportament de fluència similar s'ha observat per a tots els grups, amb diferències únicament en la deformació de fallada. L'estudi de la morfometria ha permés analitzar els paràmetres morfomètrics que diferencien les mostres sanes de les malaltes, i fins i tot a diferenciar entre diferents patologies. S'han correlacionat estos paràmetres amb la resposta mecànica per a analitzar aquells que tenen major influència sobre ella. Les correlacions obtingudes permeten estimar la resposta mecànica de l'os trabecular utilitzant les imatges micro-CT sense necessitat de realitzar assajos experimentals. Els paràmetres obtinguts de la resposta mecànica també s'han relacionat entre si. Estes relacions permeten conéixer el comportament de cadascuna de les mostres que és diferent segons la malaltia que patixen. També, s'han estudiat mostres bioinspirades i estructures TPMS obtingudes mitjançant fabricació additiva. Estes mostres bioinspirades s'han fabricat amb PLA com a material d'impressió. Les mostres mostren un comportament ortòtrop com les trabeculars. Estos simulants poden ser utilitzats per a fer estudis previs quan no es dispose de les mostres òssies. El tractament de fractures òssies de gran grandària requerix de tècniques no convencionals per a la fixació de l'os. Solen utilitzar-se bastides òssies amb triple periodicitat que tenen com a resultat propietats ortòtropes iguals en les tres direccions ortogonals. Estos sistemes han de disposar de rigideses similars a l'os en el veïnatge del defecte per a evitar l'afluixament de l'implant. S'ha proposat una metodologia que permet dissenyar bastides òssies pacient-específics que permeten ajustar les propietats mecàniques ortòtropes en cada direcció en funció de l'os., [EN] The main objective of this thesis is to analyse the effect of osteoporosis on the mechanical behaviour of cancellous bone. The behaviour of cancellous bone has been addressed through different approaches: experimental tests, finite element (FE) models and medical imaging obtained by micro-CT. The impact of osteoporosis has been studied on different scales. Firstly, a study has been undertaken at the lamellar tissue level of trabecular bone to estimate the equations that define the elastic and strength properties as a function of bone mineral density and tissue porosity. These equations are inferred from FE models and allow us to characterise the behaviour of lamellar bone tissue covering a wide range of porosities and BMDs. A study of the cancellous structure and lamellar tissue has been carried out using a stereomicroscope and FESEM. At lamellar tissue level, it was possible to observe the arrangement of lamellae in different locations, such as trabeculae and at their intersections. In addition, it has been possible to evaluate the natural tissue porosity and that produced by bone diseases. All this information has been incorporated to the numerical models in order to define the properties of cancellous bone samples. The estimated elastic and strength equations consider an orthotropic behaviour and it is possible to quantify how BMD and porosity affect these properties. On the other hand, the mechanical behaviour under compression of human trabecular bone samples from femoral heads has been studied. These samples are classified into three study groups: healthy, osteoarthrosic and osteoporotic. The samples have been studied using experimental tests, medical imaging obtained and FE models, enabling to obtain a great deal of information regarding the mechanical behaviour of the bone. The trabecular microarchitecture strongly influences the mechanical response. The most important results obtained are the apparent modulus, the failure stress and the failure strain. It was possible to generate FE models and study the morphometry of the specimens. The FE models have made it possible to estimate the properties at the tissue level. The results revealed that at the tissue level, Young's modulus does not vary appreciably, even if the bone shows bone pathology. A similar yield behaviour is observed for all groups, with differences only in the final failure strain. The morphometry study has enabled to analyse the morphometric parameters that differentiate between healthy and diseased specimens and even to differentiate between different pathologies. The morphometric parameters have been correlated with the mechanical response to analyse those that have the most significant influence on the mechanical response. The correlations obtained make it possible to estimate the mechanical response of trabecular bone using micro-CT images without the need for experimental tests. The parameters obtained from the mechanical response have also been related. These relationships permit to know the behaviour of each of the samples, which is different depending on the disease they suffer. Finally, bioinspired samples and minimal surface area triple periodic structures obtained by additive manufacturing have been studied. These samples are made of PLA as the printing material. The samples show a similar orthotropic behaviour to the trabecular samples. These simulants can be used for pre-studies when bone samples are not available. The treatment of large bone fractures requires unconventional techniques for bone fixation. Bone scaffolds with triple periodicity that result in equal orthotropic properties in all three orthogonal directions are often used. These systems must have bone-like stiffness in the vicinity of the defect to avoid implant loosening. To this end, a methodology has been proposed to design patient-specific bone scaffolds that allow the orthotropic mechanical properties in each direction to be calibrated according to a specific bone., The author and the supervisors of this PhD thesis acknowledge the Ministerio de Ciencia e Innovación y Universidades and the European Regional Development Fund (FEDER) for the financial support received through the projects PID2020-118920RB-I00 and PID2020-118480RB-C21 and C22 funded by MCIN/AEI/10.13039/501100011033, and the Generalitat Valenciana for Plan FDEGENT 2018 and Programa PROMETEO/2021/046.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Modeling the delamination failure under compressive loads in CFRP laminates based on digital image correlation analysis

  • Calvo, Jose Vicente|||0000-0001-8488-1762
  • Feito-Sánchez, Norberto|||0000-0001-7330-6404
  • Giner Maravilla, Eugenio|||0000-0003-1903-6495
  • Miguélez, María Henar
[EN] Laminate composite materials such as CFRPs are highly susceptible to delamination, being one of the common failure modes in composite laminates. The combination of severe delamination with uniaxial compressive loads leads to the loss of stability and structure failure. In this study, the authors present an experimental and numerical analysis of this effect in laminates. A series of tests were carried out with four different specimens including delamination-free plates and plates with incipient delamination with different damage size and location. 3D Digital Imagen Correlation technique was applied to predict the buckling initiation and propagation and to validate the numerical models implemented, showing good agreement between the numerical and experimental results. Model material failure includes Hashin criterion and cohesive zone model (CZM) to predict delamination. Finally, numerical models have been used to predict the crack initiation and progression in the rest of samples., This research was funded by the FEDER programme and the Spanish Ministry of Science and Innovation, under projects DPI2017-89197-C2-1-R, DPI2017-89197-C2-2-R, PID2020-118480RB-C21, PID2020-118480RB-C22 and the associated predoctoral subprogram PRE2018-086277. The funding of the Generalitat Valenciana, Programme PROMETEO 2021/046 and project GV 2021/156, is also acknowledged.
eBiltegia. Repositorio Institucional de Mondragon Unibertsitatea
Publication

On the use of the theory of critical distances with mesh control for fretting fatigue life assessment in complete and nearly complete contacts

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

The role of the interfaces and cross-links on the mechanical behavior of mineralized collagen fibrils. A numerical approach

  • Vercher-Martínez, Ana
  • Giner, Eugenio
  • Fuenmayor, F. Javier
  • García-Aznar, J. Manuel
Mechanical properties of bone tissue are highly dependent on its hierarchical structure. The presence of microcracks and diffuse damage in lamellar bone is correlated with the failure of the collagen-mineral interface in mineralized collagen fibrils (MCF). The main goal of this work is to evaluate the mechanical behavior of the interfaces and quantify the stiffness loss of the MCF associated with different failure mechanisms, under controlled in-plane displacement. Additionally, we aim to study the role of the cross-links on the fibril mechanical response, beyond the interface failure. Inter- and intra-microfibrilar cross-links are analyzed. In order to address the first issue, a detailed representative volume of the MCF is analyzed by means of the finite element method, under the assumption of plane strain and periodic boundary conditions. In this model the interfaces between constituents are modeled with an exponential cohesive law. Enzymatic cross-links, located at the molecular terminals connecting each 4D ( ) staggered molecules, are represented by non-linear springs. Three in-plane controlled deformations are applied. The results of this work provide the anisotropic stiffness loss of the tissue involved in the different failure mechanisms at the nano-scale length. The initiation of microcracks and the presence of damage zones are compatible with the failure mechanisms observed at interfaces. Interface failure entails a progressive stiffness loss, bringing a non-linear behavior of bone. The strength obtained for the longitudinal maximum deformation is more than 20 times the transverse strength and 3.5 times the shear strength. The quantification of the reduction percentage in the elastic moduli and the shear stiffness when the fibril is damaged, has a potential application in improving failure criteria based on degradation of elastic constants. When longitudinal elongation is applied, the mechanical contribution of the cross-links in delaying the failure initiation of the interface is shown. Likewise, results of this work confirm the scarce influence of the cross-links in the strain range analyzed. Additionally, a three-dimensional numerical model of several microfibrils is defined with the aim of analyzing the mechanical relevance of inter- and intra-microfibrilar cross-links, beyond the interface failure. Results confirm that cross-links transfer the load when strain increases, being highlighted the mechanical competence of the trivalent cross-links.
Docta Complutense
Publication Artículo científico (JournalArticle)

Numerical modelling of cancellous bone damage using an orthotropic failure criterion and tissue elastic properties as a function of the mineral content and microporosity

  • Larrainzar Garijo, Ricardo
  • Megías , Raquel
  • Vercher-Martínez, Ana
  • Belda, Ricardo
  • Peris, José Luis
  • Giner, Eugenio
  • Fuenmayor, Javier
Background and objective: Elastic and strength properties of lamellar tissue are essential to analyze the mechanical behaviour of bone at the meso- or macro-scale. Although many efforts have been made to model the architecture of cancellous bone, in general, isotropic elastic constants are assumed for tissue modelling, neglecting its non-isotropic behaviour. Therefore, isotropic damage laws are often used to estimate the bone failure. The main goals of this work are: (1) to present a new model for the estimation of the elastic properties of lamellar tissue which includes the bone mineral density (BMD) and the microporosity, (2) to address the numerical modelling of cancellous bone damage using an orthotropic failure criterion and a discrete damage mechanics analysis, including the novel approach for the tissue elastic properties aforementioned. Methods: Numerical homogenization has been used to estimate the elastic properties of lamellar bone considering BMD and microporosity. Microcomputed Tomography (μ-CT) scans have been performed to obtain the micro-finite element (μ-FE) model of cancellous bone from a vertebra of swine. In this model, lamellar tissue is orientated by considering a unidirectional layer pattern being the mineralized collagen fibrils aligned with the most representative geometrical feature of the trabeculae network. We have considered the Hashin's failure criterion and the Material Property Degradation (MPDG) method for simulating the onset and evolution of bone damage. Results: The terms of the stiffness matrix for lamellar tissue are derived as functions of the BMD and microporosity at tissue scale. Results obtained for the apparent yield strain values agree with experimental values found in the literature. The influence of the damage parameters on the bone mechanics behaviour is also presented. Conclusions: Stiffness matrix of lamellar tissue depends on both BMD and microporosity. The new approach presented in this work enables to analyze the influence of the BMD and porosity on the mechanical response of bone. Lamellar tissue orientation has to be considered in the mechanical analysis of the cancellous bone. An orthotropic failure criterion can be used to analyze the bone failure onset instead of isotropic criteria. The elastic property degradation method is an efficient procedure to analyze the failure propagation in a 3D numerical model.