Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 25
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Model predictive control for ethanol steam reformers with membrane separation

  • Serra-Prat, María
  • Ocampo-Martínez, Carlos
  • Li, Mingming
  • Llorca, Jordi
This paper focuses on the dynamic modelling and the predictive control of an ethanol steam reformer (ESR) with Pd[sbnd]Ag membrane separation stage for the generation of pure hydrogen. Hydrogen purity necessary to feed a proton exchange membrane fuel cell (PEMFC) is required. A non-linear dynamic model of the ESR is developed together with a procedure for adjusting the model parameters in order to fit a bank of experimental data of a real ESR system. Static and dynamic analysis of the non-linear ESR model is presented. From this non-linear model, a linear, reduced order and discretised model is derived and a model predictive controller (LMPC) is designed for the ESR system. Control objectives are pure hydrogen flowrate tracking and ethanol inlet minimization. Comparisons between the non-linear and linear models are carried out to determine the control constraints. Finally, simulation results for the implemented LMPC controller are presented and discussed., This paper has been partially supported by Spanish research projects. DPI2015-69286-C3-2-R, MINECO/FEDER and ENE2015-63969-R, MINECO/FEDER. Mingming Li has been supported by the China Scholarship Council (CSC). Jordi Llorca is Serra Húnter Fellow and is grateful to ICREA Academia program., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Fast and Simple Microwave Synthesis of TiO2/Au Nanoparticles for Gas-Phase Photocatalytic Hydrogen Generation

  • May Masnou, Anna
  • Soler, Lluís
  • Torras, Miquel
  • Sallés, Pol
  • Llorca, Jordi
  • Roig Serra, Anna
The fabrication of small anatase titanium dioxide (TiO2) nanoparticles (NPs) attached to larger anisotropic gold (Au) morphologies by a very fast and simple two-step microwave-assisted synthesis is presented. The TiO2/Au NPs are synthesized using polyvinylpyrrolidone (PVP) as reducing, capping and stabilizing agent through a polyol approach. To optimize the contact between the titania and the gold and facilitate electron transfer, the PVP is removed by calcination at mild temperatures. The nanocatalysts activity is then evaluated in the photocatalytic production of hydrogen from water/ethanol mixtures in gas-phase at ambient temperature. A maximum value of 5.3 mmol·g−1cat⋅h−1 (7.4 mmol·g−1TiO2⋅h−1) of hydrogen is recorded for the system with larger gold particles at an optimum calcination temperature of 450°C. Herein we demonstrate that TiO2-based photocatalysts with high Au loading and large Au particle size (≈50 nm) NPs have photocatalytic activity., This research received funding from the Spanish Ministry of Economy and Competitiveness (MINECO) in co-funding with European Social Funds through the MAT2015-64442-R and ENE2015-63969-R projects and financial support through the Severo Ochoa Programme for Centers of Excellence in R&D (SEV-2015-0496). MINECO also funded the FPU PhD Fellow of MT (FPU16/05452) and the Juan de la Cierva Postdoctoral Fellow of AM-M (FJCI-2014-21407). Generalitat of Catalunya is acknowledged for the projects 2017SGR752 and 2017SGR128. JL is Serra Hunter Fellow and is grateful to ICREA Academia program. The authors would also like to thank Judith Oró and Belén Ballesteros for the TEM and HRTEM images and Ana Esther Carrillo for the SEM images., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Colloidal Ni–Co–Sn nanoparticles as efficient electrocatalysts for the methanol oxidation reaction

  • Li, Junshan
  • Luo, ZhiShan
  • He, Feng
  • Zuo, Yong
  • Zhang, Chaoqi
  • Liu, Junfeng
  • Yu, Xiaoting
  • Du, Ruifeng
  • Zhang, Ting
  • Infante-Carrió, Maria F.
  • Tang, Peng-Yi
  • Arbiol, Jordi
  • Llorca, Jordi
  • Cabot, Andreu
The deployment of direct methanol fuel cells requires engineering cost-effective and durable electrocatalysts for the methanol oxidation reaction (MOR). As an alternative to noble metals, Ni-based alloys have shown excellent performance and good stability toward the MOR. Herein, we present a series of Ni3−xCoxSn2 colloidal nanoparticles (NPs) with composition tuned over the entire Ni/Co range (0 ≤ x ≤ 3). We demonstrate electrodes based on these ternary NPs to provide improved catalytic performance toward the MOR in an alkaline medium when compared with binary Ni3Sn2 NPs. A preliminary composition optimization resulted in Ni2.5Co0.5Sn2 NP-based electrodes exhibiting extraordinary mass current densities, up to 1050 mA mg−1, at 0.6 V vs. Hg/HgO in 1.0 M KOH containing 1.0 M methanol. This current density was about two-fold higher than that of Ni3Sn2 electrodes (563 mA mg−1). The excellent performance obtained with the substitution of small amounts of Ni by Co was concomitant with an increase of the surface coverage of active species and an enhancement of the diffusivity of the reaction limiting species. Additionally, saturation of the catalytic activity at higher methanol concentrations was measured for Ni3−xCoxSn2 NP-based electrodes containing a small amount of Co when compared with binary Ni3Sn2 NPs. While the electrode stability was improved with respect to elemental Ni NP-based electrodes, the introduction of small amounts of Co slightly decreased the cycling performance. Additionally, Sn, a key element to improve stability with respect to elemental Ni NPs, was observed to slowly dissolve in the presence of KOH. Density functional theory calculations on metal alloy surfaces showed the incorporation of Co within the Ni3Sn2 structure to provide more effective sites for CO and CH3OH adsorption. However, the relatively lower stability could not be related to CO or CH3OH poisoning., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through the project SEHTOP (ENE2016-77798-C4-3-R) and VALPEC (ENE2017-85087-C3). J. Li and T. Zhang thank the China Scholarship Council (CSC) for scholarship support. T. Zhang and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327. ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV-2013-0295). IREC and ICN2 are funded by the CERCA Programme/Generalitat de Catalunya. Part of the present work has been performed in the framework of the Universitat Autònoma de Barcelona Materials Science PhD program. J. Llorca is a Serra Húnter Fellow and is grateful to the ICREA Academia program and to MINECO/FEDER grant ENE2015-63969-R and GC 2017 SGR 128., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Colloidal Ni2−xCoxP nanocrystals for the hydrogen evolution reaction

  • Liu, Junfeng
  • Wang, Zhenxing
  • David, Jeremy
  • Llorca, Jordi
  • Li, Junshan
  • Yu, Xiaoting
  • Shavel, Alexey
  • Arbiol, Jordi
  • Meyns, Michaela
  • Cabot, Andreu
A cost-effective and scalable approach was developed to produce monodisperse Ni2−xCoxP nanocrystals (NCs) with composition tuned over the entire range (0 ≤ x ≤ 2). Ni2−xCoxP NCs were synthesized using low-cost, stable and low-toxicity triphenyl phosphite (TPP) as a phosphorus source, metal chlorides as metal precursors and hexadecylamine (HDA) as a ligand. The synthesis involved the nucleation of amorphous Ni–P and its posterior crystallization and simultaneous incorporation of Co. The composition, size and morphology of the Ni2−xCoxP NCs could be controlled simply by varying the ratio of Ni and Co precursors and the amounts of TPP and HDA. Ternary Ni2−xCoxP-based electrocatalysts exhibited enhanced electrocatalytic activity toward the hydrogen evolution reaction (HER) compared to binary phosphides. In particular, NiCoP electrocatalysts displayed the lowest overpotential of 97 mV at J = 10 mA cm−2 and an excellent long-term stability. DFT calculations of the Gibbs free energy for hydrogen adsorption at the surface of Ni2−xCoxP NCs showed NiCoP to have the most appropriate composition to optimize this parameter within the whole Ni2−xCoxP series. However, the hydrogen adsorption energy was demonstrated not to be the only parameter controlling the HER activity in Ni2−xCoxP., J. David and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO project VALPEC (ENE2017-85087-C3). ICN2 acknowledges support from the Severo Ochoa Programme (SEV-2013-0295) and is funded by the CERCA Programme/Generalitat de Catalunya. J. David has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Sklodowska-Curie grant agreement No 665919. J. Llorca is a Serra Hunter Fellow and is grateful to the ICREA Academia program and grants MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128. J. Liu, J. Li and X. Yu thank the China Scholarship Council for scholarship support. M. Meyns acknowledges a Juan de la Cierva formación grant by the Spanish MINECO., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

NiSn bimetallic nanoparticles as stable electrocatalysts for methanol oxidation reaction

  • Li, Junshan
  • Luo, ZhiShan
  • Zuo, Yong
  • Liu, Junfeng
  • Zhang, Ting
  • Tang, Peng-Yi
  • Arbiol, Jordi
  • Llorca, Jordi
  • Cabot, Andreu
Nickel is an excellent alternative catalyst to high cost Pt and Pt-group metals as anode material in direct methanol fuel cells. However, nickel presents a relatively low stability under operation conditions, even in alkaline media. In this work, a synthetic route to produce bimetallic NiSn nanoparticles (NPs) with tuned composition is presented. Through co-reduction of the two metals in the presence of appropriate surfactants, 3–5 nm NiSn NPs with tuned Ni/Sn ratios were produced. Such NPs were subsequently supported on carbon black and tested for methanol electro-oxidation in alkaline media. Among the different stoichiometries tested, the most Ni-rich alloy exhibited the highest electrocatalytic activity, with mass current density of 820 mA mg−1 at 0.70 V (vs. Hg/HgO). While this activity was comparable to that of pure nickel NPs, NiSn alloys showed highly improved stabilities over periods of 10,000 s at 0.70 V. We hypothesize this experimental fact to be associated to the collaborative oxidation of the byproducts of methanol which poison the Ni surface or to the prevention of the tight adsorption of these species on the Ni surface by modifying its surface chemistry or electronic density of states., J. Li and T. Zhang thank the China Scholarship Council for scholarship support. JA and TZ acknowledge funding from Generalitat de Catalunya 2014 SGR 1638 and the Spanish MINECO coordinated projects between IREC and ICN2 VALPEC and subprojects RESOL and ANAPHASE (ENE2017-85087-C3). ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV-2013-0295) and is funded by the CERCA Programme / Generalitat de Catalunya. JL is a Serra Húnter Fellow and is grateful to ICREA Academia program and to MINECO/FEDER grant ENE2015-63969-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

SnP nanocrystals as anode materials for Na-ion batteries

  • Liu, Junfeng
  • Wang, Shutao
  • Kravchyk, Kostiantyn
  • Ibáñez, María
  • Krumeich, Frank
  • Widmer, Roland
  • Nasiou, Déspina
  • Meyns, Michaela
  • Llorca, Jordi
  • Arbiol, Jordi
  • Kovalenko, Maksym V.
  • Cabot, Andreu
Tin monophosphide is a layered material consisting of Sn–P–P–Sn sandwiches that are stacked on top of each other to form a three dimensional crystallographic structure. Its composition and crystal structure makes it an excellent candidate anode material for sodium-ion batteries (SIBs). However, SnP is yet to be explored for such and other applications due to its challenging synthesis. In the present work, we report the synthesis of SnP nanocrystals (NCs) from the reaction of hexamethylphosphorous triamide (HMPT) and a tin phosphonate prepared from tin oxalate and a long chain phosphonic acid. SnP NCs obtained from this reaction displayed a spherical geometry and a trigonal crystallographic phase with a superstructure attributed to ordered diphosphorus pairs. Such NCs were mixed with carbon black and used as anode materials in SIBs. SIBs based on SnP NCs and sodium(I) bis(fluorosulfonyl)imide (NaFSI) electrolyte displayed a high reversible capacity of 600 mA h g−1 at a current density of 100 mA g−1 and cycling stability for over 200 cycles. Their excellent cycling performance is associated with both the small size of the crystal domains and the particular composition and phase of SnP which prevent mechanical disintegration and major phase separation during sodiation and desodiation cycles. These results demonstrate SnP to be an attractive anode material for sodium ion batteries., DN and JA acknowledge funding from Generalitat de Catalunya 2014 SGR 1638 and the Spanish MINECO projects VALPEC and ANAPHASE (ENE2017-85087-C3-3-R). The ICN2 acknowledges support from the Severo Ochoa Programme (SEV-2013-0295) and is funded by Generalitat de Catalunya. JL thanks the China Scholarship Council for scholarship support. MM acknowledges a Juan de la Cierva formación grant by the Spanish MINECO. JLl is a Serra Húnter Fellow and is grateful to ICREA Academia program and projects MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Compositionally tuned NixSn alloys as anode materials for lithium-ion and sodium-ion batteries with a high pseudocapacitive contribution

  • Li, Junshan
  • Xu, Xijun
  • Luo, ZhiShan
  • Zhang, Chaoqi
  • Yu, Xiaoting
  • Zuo, Yong
  • Zhang, Ting
  • Tang, Peng-Yi
  • Arbiol, Jordi
  • Llorca, Jordi
  • Liu, Jun
  • Cabot, Andreu
Nickel tin alloy nanoparticles (NPs) with tuned composition NixSn (0.6 ≤ x ≤ 1.9) were synthesized by a solution-based procedure and used as anode materials for Li-ion batteries (LIBs) and Na-ion batteries (SIBs). Among the compositions tested, Ni0.9Sn-based electrodes exhibited the best performance in both LIBs and SIBs. As LIB anodes, Ni0.9Sn-based electrodes delivered charge-discharge capacities of 980 mAh g−1 after 340 cycles at 0.2 A g−1 rate, which surpassed their maximum theoretical capacity considering that only Sn is lithiated. A kinetic characterization of the charge-discharge process demonstrated the electrode performance to be aided by a significant pseudocapacitive contribution that compensated for the loss of energy storage capacity associated to the solid-electrolyte interphase formation. This significant pseudocapacitive contribution, which not only translated into higher capacities but also longer durability, was associated to the small size of the crystal domains and the proper electrode composition. The performance of NixSn-based electrodes toward Na-ion storage was also characterized, reaching significant capacities above 200 mAh g−1 at 0.1 A g−1 but with a relatively fast fade over 120 continuous cycles. A relatively larger pseudocapacitive contribution was obtained in NixSn-based electrodes for SIBs when compared with LIBs, consistently with the lower contribution of the Na ion diffusion associated to its larger size., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through the project SEHTOP (ENE2016-77798-C4-3-R). J. Li thanks the China Scholarship Council for scholarship support. This project was supported by the National Natural Science Foundation of China (no. 51771076), the “1000 plan” from Chinese Government, and the Project of Public Interest Research and Capacity Building of Guangdong Province (no. 2017A010104004). T. Zhang, P. Tang and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO coordinated projects between IREC and ICN2 VALPEC and subprojects RESOL and ANAPHASE (ENE2017-85087-C3). ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV-2013-0295) and is funded by the CERCA Programme / Generalitat de Catalunya. T. Zhang has received funding from the CSC-UAB PhD scholarship program. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program. J. Llorca is a Serra Húnter Fellow and is grateful to ICREA Academia program and to MINECO/FEDER grant ENE2015-63969-R and GC 2017 SGR 128., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Co–Sn nanocrystalline solid solutions as anode materials in lithium-ion batteries with high pseudocapacitive contribution

  • Li, Junshan
  • Xu, Xijun
  • Luo, ZhiShan
  • Zhang, Chaoqi
  • Zuo, Yong
  • Zhang, Ting
  • Tang, Peng-Yi
  • Infante-Carrió, Maria F.
  • Arbiol, Jordi
  • Llorca, Jordi
  • Liu, Jun
  • Cabot, Andreu
Co–Sn solid‐solution nanoparticles with Sn crystal structure and tuned metal ratios were synthesized by a facile one pot solution‐based procedure involving the initial reduction of a Sn precursor followed by incorporation of Co within the Sn lattice. These nanoparticles were used as anode materials for Li‐ion batteries. Among the different compositions tested, Co0.7Sn and Co0.9Sn electrodes provided the highest capacities with values above 1500 mAh g−1 at a current density of 0.2 A g−1 after 220 cycles, and up to 800 mAh g−1 at 1.0 A g−1 after 400 cycles. Up to 81 % pseudocapacitance contribution was measured for these electrodes at a sweep rate of 1.0 mV s−1, thereby indicating fast kinetics and long durability. The excellent performance of Co–Sn nanoparticle alloy‐based electrodes was attributed to both the small size of the crystal domains and their suitable composition, which buffered volume changes of Sn and contributed to a suitable electrode restructuration., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through the project SEHTOP (ENE2016‐77798‐C4‐3‐R). J. Li thanks the China Scholarship Council for scholarship support. This project was supported by the National Natural Science Foundation of China (no. 51771076), the “1000 plan” from Chinese Government, and the Project of Public Interest Research and Capacity Building of Guangdong Province (no. 2017A010104004). TZ, PYT, MFIC and JA acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO coordinated projects between IREC and ICN2 VALPEC and subprojects RESOL and ANAPHASE (ENE2017‐85087‐C3). ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV‐2013‐0295) and is funded by the CERCA Programme/ Generalitat de Catalunya. JL is a Serra Húnter Fellow and is grateful to ICREA Academia program and to MINECO/FEDER grant ENE2015‐63969‐R. TZ has received funding from the CSC‐UAB PhD scholarship program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Chromium phosphide CrP as highly active and stable electrocatalysts for oxygen electroreduction in alkaline media

  • Liu, Junfeng
  • Yu, Xiaoting
  • Du, Ruifeng
  • Zhang, Chaoqi
  • Zhang, Ting
  • Llorca, Jordi
  • Arbiol, Jordi
  • Wang, Ying
  • Meyns, Michaela
  • Cabot, Andreu
Catalysts for oxygen reduction reaction (ORR) are key components in emerging energy technologies such as fuel cells and metal-air batteries. Developing low-cost, high performance and stable electrocatalysts is critical for the extensive implementation of these technologies. Herein, we present a procedure to prepare colloidal chromium phosphide CrP nanocrystals and we test their performance as ORR electrocatalyst. CrP-based catalysts exhibited remarkable activities with a limiting current density of 4.94 mA cm−2 at 0.2 V, a half-potential of 0.65 V and an onset potential of 0.8 V at 1600 rpm, which are comparable to commercial Pt/C. Advantageously, CrP-based catalysts displayed much higher stabilities and higher tolerances to methanol in alkaline solution. Using density functional theory calculations, we demonstrate CrP to provide a very strong chemisorption of O2 that facilitates its reduction and explains the excellent ORR performance experimentally demonstrated., This work was supported by the European Regional Development Funds and the Spanish MINECO project SEHTOP (ENE2016-77798-C4- 3-R). T. Zhang and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO project ENE2017-85087-C3. ICN2 is supported by the Severo Ochoa program from Spanish MINECO (SEV-2017-0706) and is funded by the CERCA Programme / Generalitat de Catalunya. J. Llorca is a Serra Hunter Fellow and is grateful to ICREA Academia program and grants MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128. J. Liu, X. Yu, R. Du, C. Zhang and T. Zhang thank the China Scholarship Council for scholarship support. M. Meyns acknowledges a Juan de la Cierva formación grant by theSpanish MINECO. Y. Wang thanks the National Natural Science Foundation of China for financial support (Grant Nos: 21673220, 21831003, 21733004), National Key Research and Development Program of China (2016YFA0602900) and High performance Computing Center of Jilin Province and Computing Center of Jilin University for essential support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Graphene-supported palladium phosphide PdP2 nanocrystals for ethanol electrooxidation

  • Liu, Junfeng
  • Luo, ZhiShan
  • Li, Junshan
  • Yu, Xiaoting
  • Llorca, Jordi
  • Nasiou, Déspina
  • Arbiol, Jordi
  • Meyns, Michaela
  • Cabot, Andreu
We present a procedure to produce single-phase PdP2 nanocrystals (NCs). The approach involves the reaction of palladium(II) acetylacetonate and hexamethylphosphoroustriamide to nucleate defective Pd5P2 nanoparticles that subsequently, with further phosphorous incorporation, crystallize into PdP2. The synthesized PdP2 NCs were supported on reduced graphene oxide (rGO) and applied as electrocatalysts for ethanol oxidation. The activity of PdP2 toward the ethanol oxidation reaction (EOR) was over a threefold higher than that of Pd NCs prepared under similar conditions. Even better performance was obtained from PdP2 NCs supported on rGO, which showed current densities up to 51.4 mA cm−2 and mass activities of 1.60 A mg-1Pd, that is 4.8 and 15 times higher than Pd NCs. Besides, PdP2 NCs and PdP2/rGO catalysts showed improved stability during EOR than Pd NCs and Pd/rGO., This work was supported by the European Regional Development Funds and the Spanish MINECO project SEHTOP (ENE2016-77798-C4-3-R). D. Nasiou and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO project ANAPHASE (ENE2017-85087-C3). ICN2 acknowledges support from the Severo Ochoa Programme (SEV-2013-0295) and is funded by the CERCA Programme / Generalitat de Catalunya. J. Llorca is a Serra Hunter Fellow and is grateful to ICREA Academia program and grants MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128. J. Liu, J. Li and X. Yu thank the China Scholarship Council for scholarship support. M. Meyns acknowledges a Juan de la Cierva formación grant by the Spanish MINECO., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Porous NiTiO3/TiO2 nanostructures for photocatatalytic hydrogen evolution

  • Xing, Congcong
  • Liu, Yongpeng
  • Zhang, Yu
  • Liu, Junfeng
  • Zhang, Ting
  • Tang, Peng-Yi
  • Arbiol, Jordi
  • Soler, Lluís
  • Sivula, Kevin
  • Guijarro, Néstor
  • Wang, Xiang
  • Li, Junshan
  • Du, Ruifeng
  • Zuo, Yong
  • Cabot, Andreu
  • Llorca, Jordi
We present a strategy to produce porous NiTiO3/TiO2 nanostructures with excellent photocatalytic activity toward hydrogen generation. In a first step, nickel-doped TiO2 needle bundles were synthesized by a hydrothermal procedure. Through the sintering in air of these nanostructures, porous NiTiO3/TiO2 heterostructured rods were obtained. Alternatively, the annealing in argon of the nickel-doped TiO2 needle bundles resulted in NiOx/TiO2 elongated nanostructures. Porous NiTiO3/TiO2 structures were tested for hydrogen evolution in the presence of ethanol. Such porous heterostructures exhibited superior photocatalytic activity toward hydrogen generation, with hydrogen production rates up to 11.5 mmol h−1 g−1 at room temperature. This excellent performance is related here to the optoelectronic properties and geometric parameters of the material., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through projects ENE2016-77798-C4-3-R and ENE2015-63969-R. Y. L. and N. G. thank the Swiss National Science Foundation (SNF) for funding under the Ambizione Energy grant no. PZENP2_166871. J.L. is a Serra Hunter fellow and is grateful to ICREA Academia program and GC 2017 SGR 128. T. Z., P.·Y. T. and J. A. acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO project ENE2017-85087-C3. ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV-2013-0295) and is funded by the CERCA Programme/Generalitat de Catalunya. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program. C. C. X., Y. Z and T. Z. thank the China Scholarship Council for scholarship support., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Solution-processed ultrathin SnS2−Pt nanoplates for photoelectrochemical water oxidation

  • Zuo, Yong
  • Liu, Yongpeng
  • Li, Junshan
  • Du, Ruifeng
  • Yu, Xiaoting
  • Xing, Congcong
  • Zhang, Ting
  • Yao, Liang
  • Arbiol, Jordi
  • Llorca, Jordi
  • Sivula, Kevin
  • Guijarro, Néstor
  • Cabot, Andreu
Tin disulfide (SnS2) is attracting significant interest because of the abundance of its elements and its excellent optoelectronic properties in part related to its layered structure. In this work, we specify the preparation of ultrathin SnS2 nanoplates (NPLs) through a hot-injection solution-based process. Subsequently, Pt was grown on their surface via in situ reduction of a Pt salt. The photoelectrochemical (PEC) performance of such nanoheterostructures as photoanode toward water oxidation was tested afterwards. Optimized SnS2–Pt photoanodes provided significantly higher photocurrent densities than bare SnS2 and SnS2-based photoanodes of previously reported study. Mott–Schottky analysis and PEC impedance spectroscopy (PEIS) were used to analyze in more detail the effect of Pt on the PEC performance. From these analyses, we attribute the enhanced activity of SnS2–Pt photoanodes reported here to a combination of the very thin SnS2 NPLs and the proper electronic contact between Pt nanoparticles (NPs) and SnS2., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through the project SEHTOP (ENE2016-77798-C4-3-R) and VALPEC (ENE2017-85087-C3). Y.Z., J.L., R.D., X.T., and T.Z. thank China Scholarship Council for scholarship support. Y.L. and N.G. thank the Swiss National Science Foundation (SNF) for funding under the Ambizione Energy grant no. PZENP2_166871. J.L. is a Serra Húnter Fellow and is grateful to ICREA Academia program and grants MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128. T.Z. and J.A. acknowledge funding from Generalitat de Catalunya 2017 SGR 327. ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, grant no. SEV-2013-0295). IREC and ICN2 are funded by the CERCA Programme/Generalitat de Catalunya. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program., Peer reviewed
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Ligand Migration from Cluster to Support, A Crucial Factor for Catalysis by Thiolate-protected Gold Clusters

  • Zhang, Bei
  • Sels, Annelies
  • Salassa, Giovanni|||0000-0002-2396-3884
  • Pollitt, Stephan
  • Truttmann, Vera
  • Rameshan, Christoph|||0000-0002-6340-4147
  • Llorca, Jordi|||0000-0002-7447-9582
  • Olszewski, Wojciech|||0000-0002-4682-4326
  • Rupprechter, Günther|||0000-0002-8040-1677
  • Bürgi, Thomas|||0000-0003-0906-082X
  • Barrabés, Noelia|||0000-0002-6018-3115
Thiolate protected metal clusters are valuable precursors for the design of tailored nanosized catalysts. Their performance can be tuned precisely at atomic level, e. g. by the configuration/type of ligands or by partial/complete removal of the ligand shell through controlled pre-treatment steps. However, the interaction between the ligand shell and the oxide support, as well as ligand removal by oxidative pre-treatment, are still poorly understood. Typically, it was assumed that the thiolate ligands are simply converted into SO, CO and HO. Herein, we report the first detailed observation of sulfur ligand migration from Au to the oxide support upon deposition and oxidative pre-treatment, employing mainly S K-edge XANES. Consequently, thiolate ligand migration not only produces clean Au cluster surfaces but also the surrounding oxide support is modified by sulfur-containing species, with pronounced effects on catalytic properties.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

NiSn bimetallic nanoparticles as stable electrocatalysts for methanol oxidation reaction

  • Li, Junshan|||0000-0002-1482-1972
  • Luo, Zhishan|||0000-0002-0801-9238
  • Zuo, Yong|||0000-0003-1564-467X
  • Liu, Junfeng|||0000-0003-3164-6472
  • Zhang, Ting|||0000-0002-0317-9662
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Nickel is an excellent alternative catalyst to high cost Pt and Pt-group metals as anode material in direct methanol fuel cells. However, nickel presents a relatively low stability under operation conditions, even in alkaline media. In this work, a synthetic route to produce bimetallic NiSn nanoparticles (NPs) with tuned composition is presented. Through co-reduction of the two metals in the presence of appropriate surfactants, 3-5 nm NiSn NPs with tuned Ni/Sn ratios were produced. Such NPs were subsequently supported on carbon black and tested for methanol electro-oxidation in alkaline media. Among the different stoichiometries tested, the most Ni-rich alloy exhibited the highest electrocatalytic activity, with mass current density of 820 mA mg⁻¹ at 0.70 V (vs. Hg/HgO). While this activity was comparable to that of pure nickel NPs, NiSn alloys showed highly improved stabilities over periods of 10,000 s at 0.70 V. We hypothesize this experimental fact to be associated to the collaborative oxidation of the byproducts of methanol which poison the Ni surface or to the prevention of the tight adsorption of these species on the Ni surface by modifying its surface chemistry or electronic density of states.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Compositionally tuned NixSn alloys as anode materials for lithium-ion and sodium-ion batteries with a high pseudocapacitive contribution

  • Li, Junshan|||0000-0002-1482-1972
  • Xu, Xijun
  • Luo, Zhishan|||0000-0002-0801-9238
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Zuo, Yong|||0000-0003-1564-467X
  • Zhang, Ting|||0000-0002-0317-9662
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Liu, Jun|||0000-0001-5288-3042
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Nickel tin alloy nanoparticles (NPs) with tuned composition NixSn (0.6 ≤ x ≤ 1.9) were synthesized by a solution-based procedure and used as anode materials for Li-ion batteries (LIBs) and Na-ion batteries (SIBs). Among the compositions tested, Ni₀₉Sn-based electrodes exhibited the best performance in both LIBs and SIBs. As LIB anodes, Ni₀₉Sn-based electrodes delivered charge-discharge capacities of 980 mAh g⁻¹ after 340 cycles at 0.2 A g⁻¹ rate, which surpassed their maximum theoretical capacity considering that only Sn is lithiated. A kinetic characterization of the charge-discharge process demonstrated the electrode performance to be aided by a significant pseudocapacitive contribution that compensated for the loss of energy storage capacity associated to the solid-electrolyte interphase formation. This significant pseudocapacitive contribution, which not only translated into higher capacities but also longer durability, was associated to the small size of the crystal domains and the proper electrode composition. The performance of NixSn-based electrodes toward Na-ion storage was also characterized, reaching significant capacities above 200 mAh g⁻¹ at 0.1 A g⁻¹ but with a relatively fast fade over 120 continuous cycles. A relatively larger pseudocapacitive contribution was obtained in Ni Sn-based electrodes for SIBs when compared with LIBs, consistently with the lower contribution of the Na ion diffusion associated to its larger size.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Colloidal Ni2-, XCoxP nanocrystals for the hydrogen evolution reaction

  • Liu, Junfeng|||0000-0003-3164-6472
  • Wang, Zhenxing|||0000-0001-5083-0975
  • David, Jérémy|||0000-0003-3219-149X
  • Llorca, Jordi|||0000-0002-7447-9582
  • Li, Junshan|||0000-0002-1482-1972
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Shavel, Alexey|||0000-0002-3995-0391
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Meyns, Michaela|||0000-0003-2476-9001
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
A cost-effective and scalable approach was developed to produce monodisperse NiCoP nanocrystals (NCs) with composition tuned over the entire range (0 ≤ x ≤ 2). NiCoP NCs were synthesized using low-cost, stable and low-toxicity triphenyl phosphite (TPP) as a phosphorus source, metal chlorides as metal precursors and hexadecylamine (HDA) as a ligand. The synthesis involved the nucleation of amorphous Ni-P and its posterior crystallization and simultaneous incorporation of Co. The composition, size and morphology of the NiCoP NCs could be controlled simply by varying the ratio of Ni and Co precursors and the amounts of TPP and HDA. Ternary NiCoP-based electrocatalysts exhibited enhanced electrocatalytic activity toward the hydrogen evolution reaction (HER) compared to binary phosphides. In particular, NiCoP electrocatalysts displayed the lowest overpotential of 97 mV at J = 10 mA cm and an excellent long-term stability. DFT calculations of the Gibbs free energy for hydrogen adsorption at the surface of NiCoP NCs showed NiCoP to have the most appropriate composition to optimize this parameter within the whole NiCoP series. However, the hydrogen adsorption energy was demonstrated not to be the only parameter controlling the HER activity in NiCoP.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Colloidal Ni-Co-Sn nanoparticles as efficient electrocatalysts for the methanol oxidation reaction

  • Li, Junshan|||0000-0002-1482-1972
  • Luo, Zhishan|||0000-0002-0801-9238
  • He, Feng
  • Zuo, Yong|||0000-0003-1564-467X
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Liu, Junfeng|||0000-0003-3164-6472
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Du, Ruifeng
  • Zhang, Ting|||0000-0002-0317-9662
  • Infante Carrió, María F.
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
The deployment of direct methanol fuel cells requires engineering cost-effective and durable electrocatalysts for the methanol oxidation reaction (MOR). As an alternative to noble metals, Ni-based alloys have shown excellent performance and good stability toward the MOR. Herein, we present a series of NiCoSn colloidal nanoparticles (NPs) with composition tuned over the entire Ni/Co range (0 ≤ x ≤ 3). We demonstrate electrodes based on these ternary NPs to provide improved catalytic performance toward the MOR in an alkaline medium when compared with binary NiSn NPs. A preliminary composition optimization resulted in NiCoSn NP-based electrodes exhibiting extraordinary mass current densities, up to 1050 mA mg, at 0.6 V vs. Hg/HgO in 1.0 M KOH containing 1.0 M methanol. This current density was about two-fold higher than that of NiSn electrodes (563 mA mg). The excellent performance obtained with the substitution of small amounts of Ni by Co was concomitant with an increase of the surface coverage of active species and an enhancement of the diffusivity of the reaction limiting species. Additionally, saturation of the catalytic activity at higher methanol concentrations was measured for NiCoSn NP-based electrodes containing a small amount of Co when compared with binary NiSn NPs. While the electrode stability was improved with respect to elemental Ni NP-based electrodes, the introduction of small amounts of Co slightly decreased the cycling performance. Additionally, Sn, a key element to improve stability with respect to elemental Ni NPs, was observed to slowly dissolve in the presence of KOH. Density functional theory calculations on metal alloy surfaces showed the incorporation of Co within the NiSn structure to provide more effective sites for CO and CHOH adsorption. However, the relatively lower stability could not be related to CO or CHOH poisoning.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

SnP nanocrystals as anode materials for Na-ion batteries

  • Liu, Junfeng|||0000-0003-3164-6472
  • Wang, Shutao|||0000-0002-1689-2272
  • Kravchyk, Kostiantyn
  • Ibáñez, Maria|||0000-0001-5013-2843
  • Krumeich, Frank|||0000-0001-5625-1536
  • Widmer, Roland
  • Nasiou, Déspina
  • Meyns, Michaela|||0000-0003-2476-9001
  • Llorca, Jordi|||0000-0002-7447-9582
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Kovalenko, Maksym V.|||0000-0002-6396-8938
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Tin monophosphide is a layered material consisting of Sn-P-P-Sn sandwiches that are stacked on top of each other to form a three dimensional crystallographic structure. Its composition and crystal structure makes it an excellent candidate anode material for sodium-ion batteries (SIBs). However, SnP is yet to be explored for such and other applications due to its challenging synthesis. In the present work, we report the synthesis of SnP nanocrystals (NCs) from the reaction of hexamethylphosphorous triamide (HMPT) and a tin phosphonate prepared from tin oxalate and a long chain phosphonic acid. SnP NCs obtained from this reaction displayed a spherical geometry and a trigonal crystallographic phase with a superstructure attributed to ordered diphosphorus pairs. Such NCs were mixed with carbon black and used as anode materials in SIBs. SIBs based on SnP NCs and sodium(i) bis(fluorosulfonyl)imide (NaFSI) electrolyte displayed a high reversible capacity of 600 mA h g at a current density of 100 mA g and cycling stability for over 200 cycles. Their excellent cycling performance is associated with both the small size of the crystal domains and the particular composition and phase of SnP which prevent mechanical disintegration and major phase separation during sodiation and desodiation cycles. These results demonstrate SnP to be an attractive anode material for sodium ion batteries.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Co-Sn Nanocrystalline Solid Solutions as Anode Materials in Lithium-Ion Batteries with High Pseudocapacitive Contribution

  • Li, Junshan|||0000-0002-1482-1972
  • Xu, Xijun
  • Luo, Zhishan|||0000-0002-0801-9238
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Zuo, Yong|||0000-0003-1564-467X
  • Zhang, Ting|||0000-0002-0317-9662
  • Tang, PengYi|||0000-0002-2306-095X
  • Infante Carrió, María F.
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Liu, Jun|||0000-0001-5288-3042
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Co-Sn solid-solution nanoparticles with Sn crystal structure and tuned metal ratios were synthesized by a facile one pot solution-based procedure involving the initial reduction of a Sn precursor followed by incorporation of Co within the Sn lattice. These nanoparticles were used as anode materials for Li-ion batteries. Among the different compositions tested, Co Sn and Co Sn electrodes provided the highest capacities with values above 1500 mAh g at a current density of 0.2 A g after 220 cycles, and up to 800 mAh g at 1.0 A g after 400 cycles. Up to 81 % pseudocapacitance contribution was measured for these electrodes at a sweep rate of 1.0 mV s , thereby indicating fast kinetics and long durability. The excellent performance of Co-Sn nanoparticle alloy-based electrodes was attributed to both the small size of the crystal domains and their suitable composition, which buffered volume changes of Sn and contributed to a suitable electrode restructuration.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Solution-Processed Ultrathin SnS2-Pt Nanoplates for Photoelectrochemical Water Oxidation

  • Zuo, Yong|||0000-0003-1564-467X
  • Liu, Yongpeng|||0000-0002-4544-4217
  • Li, Junshan|||0000-0002-1482-1972
  • Du, Ruifeng
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Xing, Congcong|||0000-0001-7674-6720
  • Zhang, Ting|||0000-0002-0317-9662
  • Yao, Liang
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Sivula, Kevin|||0000-0002-8458-0270
  • Guijarro, Néstor|||0000-0002-3277-8816
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Tin disulfide (SnS ) is attracting significant interest because of the abundance of its elements and its excellent optoelectronic properties in part related to its layered structure. In this work, we specify the preparation of ultrathin SnS nanoplates (NPLs) through a hot-injection solution-based process. Subsequently, Pt was grown on their surface via in situ reduction of a Pt salt. The photoelectrochemical (PEC) performance of such nanoheterostructures as photoanode toward water oxidation was tested afterwards. Optimized SnS -Pt photoanodes provided significantly higher photocurrent densities than bare SnS and SnS -based photoanodes of previously reported study. Mott-Schottky analysis and PEC impedance spectroscopy (PEIS) were used to analyze in more detail the effect of Pt on the PEC performance. From these analyses, we attribute the enhanced activity of SnS -Pt photoanodes reported here to a combination of the very thin SnS NPLs and the proper electronic contact between Pt nanoparticles (NPs) and SnS .
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Porous NiTiO3/TiO2 nanostructures for photocatatalytic hydrogen evolution

  • Xing, Congcong|||0000-0001-7674-6720
  • Liu, Yongpeng|||0000-0002-4544-4217
  • Zhang, Yu|||0000-0002-0332-0013
  • Liu, Junfeng|||0000-0003-3164-6472
  • Zhang, Ting|||0000-0002-0317-9662
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Soler, Lluís|||0000-0003-1591-3366
  • Sivula, Kevin|||0000-0002-8458-0270
  • Guijarro, Néstor|||0000-0002-3277-8816
  • Wang, Xiang
  • Li, Junshan|||0000-0002-1482-1972
  • Du, Ruifeng
  • Zuo, Yong|||0000-0003-1564-467X
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
  • Llorca, Jordi|||0000-0002-7447-9582
We present a strategy to produce porous NiTiO/TiO nanostructures with excellent photocatalytic activity toward hydrogen generation. In a first step, nickel-doped TiO needle bundles were synthesized by a hydrothermal procedure. Through the sintering in air of these nanostructures, porous NiTiO/TiO heterostructured rods were obtained. Alternatively, the annealing in argon of the nickel-doped TiO needle bundles resulted in NiO/TiO elongated nanostructures. Porous NiTiO/TiO structures were tested for hydrogen evolution in the presence of ethanol. Such porous heterostructures exhibited superior photocatalytic activity toward hydrogen generation, with hydrogen production rates up to 11.5 mmol h g at room temperature. This excellent performance is related here to the optoelectronic properties and geometric parameters of the material.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Chromium phosphide CrP as highly active and stable electrocatalysts for oxygen electroreduction in alkaline media

  • Liu, Junfeng|||0000-0003-3164-6472
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Du, Ruifeng
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Zhang, Ting|||0000-0002-0317-9662
  • Llorca, Jordi|||0000-0002-7447-9582
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Wang, Ying
  • Meyns, Michaela|||0000-0003-2476-9001
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Catalysts for oxygen reduction reaction (ORR) are key components in emerging energy technologies such as fuel cells and metal-air batteries. Developing low-cost, high performance and stable electrocatalysts is critical for the extensive implementation of these technologies. Herein, we present a procedure to prepare colloidal chromium phosphide CrP nanocrystals and we test their performance as ORR electrocatalyst. CrP-based catalysts exhibited remarkable activities with a limiting current density of 4.94 mA cm at 0.2 V, a half-potential of 0.65 V and an onset potential of 0.8 V at 1600 rpm, which are comparable to commercial Pt/C. Advantageously, CrP-based catalysts displayed much higher stabilities and higher tolerances to methanol in alkaline solution. Using density functional theory calculations, we demonstrate CrP to provide a very strong chemisorption of O that facilitates its reduction and explains the excellent ORR performance experimentally demonstrated.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Graphene-supported palladium phosphide PdP2 nanocrystals for ethanol electrooxidation

  • Liu, Junfeng|||0000-0003-3164-6472
  • Luo, Zhishan|||0000-0002-0801-9238
  • Li, Junshan|||0000-0002-1482-1972
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Llorca, Jordi|||0000-0002-7447-9582
  • Nasiou, Déspina
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Meyns, Michaela|||0000-0003-2476-9001
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
We present a procedure to produce single-phase PdP nanocrystals (NCs). The approach involves the reaction of palladium(II) acetylacetonate and hexamethylphosphoroustriamide to nucleate defective Pd P nanoparticles that subsequently, with further phosphorous incorporation, crystallize into PdP . The synthesized PdP NCs were supported on reduced graphene oxide (rGO) and applied as electrocatalysts for ethanol oxidation. The activity of PdP toward the ethanol oxidation reaction (EOR) was over a threefold higher than that of Pd NCs prepared under similar conditions. Even better performance was obtained from PdP NCs supported on rGO, which showed current densities up to 51.4 mA cm and mass activities of 1.60 A mg , that is 4.8 and 15 times higher than Pd NCs. Besides, PdP NCs and PdP /rGO catalysts showed improved stability during EOR than Pd NCs and Pd/rGO.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Superior methanol electrooxidation performance of (110)-faceted nickel polyhedral nanocrystals

  • Li, Junshan|||0000-0002-1482-1972
  • Zuo, Yong|||0000-0003-1564-467X
  • Liu, Junfeng|||0000-0003-3164-6472
  • Wang, Xiang
  • Yu, Xiaoting|||0000-0003-0457-4047
  • Du, Ruifeng
  • Zhang, Ting|||0000-0002-0317-9662
  • Infante Carrió, María F.
  • Tang, PengYi|||0000-0002-2306-095X
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Luo, Zhishan|||0000-0002-0801-9238
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
We present the synthesis of (110)-faceted nickel polyhedral nanocrystals (NCs) and their characterization as electrocatalysts for the methanol oxidation reaction (MOR). Ni NCs were produced at 180 °C through the reduction in solution of a Ni salt. They were combined with carbon black and Nafion and deposited over glassy carbon to study their electrocatalytic properties. Electrodes based on (110)-faceted Ni NCs displayed a first order reaction with KOH in the concentration range from 0.1 M to 1.0 M. These electrodes were characterized by higher coverages of active species, but lower diffusion coefficients of the species limiting the reaction rate when compared with electrodes prepared from spherical Ni NCs. Overall, electrodes based on faceted Ni NCs displayed excellent performance with very high current densities, up to 61 mA cm, and unprecedented mass activities, up to 2 A mg, at 0.6 V vs. Hg/HgO in 1.0 M KOH containing 1.0 M methanol. These electrodes also displayed a notable stability. While they suffered an activity loss of ca. 30% during the first 10000 s of operation, afterward activity stabilized at very high current densities, ∼35 mA cm, and mass activities, ∼1.2 A mg, with only a 0.5% decrease during operation from 20000 to 30000 s.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

A low temperature solid state reaction to produce hollow MnxFe3-xO4 nanoparticles as anode for lithium-ion batteries

  • Yu, Xiaoting|||0000-0003-0457-4047
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Luo, Zhishan|||0000-0002-0801-9238
  • Zhang, Ting|||0000-0002-0317-9662
  • Liu, Junfeng|||0000-0003-3164-6472
  • Li, Junshan|||0000-0002-1482-1972
  • Zuo, Yong|||0000-0003-1564-467X
  • Jacas Biendicho, Jordi|||0000-0001-5981-6168
  • Llorca, Jordi|||0000-0002-7447-9582
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Morante, Joan Ramon|||0000-0002-4981-4633
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Hollow MnFeO nanoparticles (NPs) with an average size of 15 nm are produced from the solid state reaction of FeO-MnO heterostructures. These heterostructures are synthesized through the seeded-growth of MnO crystal domains on the surface of hollow FeO NPs obtained by the nanoscale Kirkendall effect. FeO-MnO heterostructures are subsequently annealed at 500 °C, enough temperature to promote the interfusion of Fe and Mn ions, but without compromising the hollow geometry. MnFeO nanostructures are tested as anode in lithium-ion batteries (LIBs), delivering large lithium storage capacities and high-rate capabilities of 1054 mAh g at 0.1 A g and 369 mAh g at 5 A g. Additionally, hollow MnFeO NPs display long cycling stability, with a capacity up to 887 mAh g at 0.3 A g after 450 cycles. The excellent performance of hollow MnFeO NPs as anode for LIBs is associated with their crystal structure, composition, and the presence of carbonized ligands, which further promote electrical conductivity and buffer the volume changes during cycling. Additionally, the small particle size and hollow morphology improves the lithium kinetics, structural stability and cycling performance.