Skip to main content

NANOSCOPIAS ELECTRONICAS AVANZADAS PARA EL DESARROLLO Y MEJORA DE NUEVAS RUTAS FOTOELECTROCATALITICAS PARA PRODUCTOS DE ALTO VALOR AÑADIDO APROVECHANDO LA ENERGIA SOLAR

ENE2017-85087-C3-3-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre FUNDACIÓ INSTITUT CATALÀ DE NANOCIÈNCIA I NANOTECNOLOGIA

Resultados relacionados

Resultados totales (Incluyendo duplicados): 27
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Controllable vapor phase fabrication of F:Mn3O4 thin films functionalized with Ag and TiO2

  • Bigiani, Lorenzo
  • Barreca, Davide
  • Gasparotto, Alberto
  • Sada, Cinzia
  • Martí-Sànchez, Sara
  • Arbiol, Jordi
  • Maccato, Chiara
A facile two-step vapor phase synthetic approach is proposed for the fabrication of Mn3O4 thin films chemically modified with fluorine, and eventually functionalized with silver or titania. The adopted strategy exploits the initial chemical vapor deposition (CVD) of Mn3O4 on Si(100) substrates starting from a diamine diketonate Mn(II) complex, followed by the controlled radio frequency (RF)-sputtering of silver or titania. Complementary analytical techniques were employed to investigate the crystallinity (X-ray diffraction), chemical composition (X-ray photoelectron spectroscopy, secondary ion mass spectrometry, energy dispersive X-ray spectroscopy), morphology and nano-organization (field emission-scanning electron microscopy, atomic force microscopy, transmission electron microscopy) of both pristine and functionalized manganese oxide thin films. Under the adopted operating conditions, the target Mn(II) complex acted as a single-source precursor for both Mn and F, leading to the formation of phase-pure hausmannite Mn3O4 films characterized by a uniform in-depth fluorine content. In addition, the obtained results gave evidence of the formation of high purity Ag/F:Mn3O4 and TiO2/F:Mn3O4 composites with a close contact between the single constituents. This work outlines an amenable and efficient method for the vapor phase growth of composite Mn3O4-based thin films, which are favorable candidates for diverse technological applications, from photocatalysis to gas sensing., This work was financially supported by Padova University DOR 2016–2017 and P-DiSC #03BIRD2016-UNIPD projects. Funding from “Programa Internacional de Becas “la Caixa”-Severo Ochoa”, Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO ENE2017-85087-C3-3-R is also acknowledged. Catalan Institute of Nanoscience and Nanotechnology (ICN2) acknowledges support from the Severo Ochoa Program (MINECO, Grant SEV-2013-0295) and is funded by the CERCA Programme/Generalitat de Catalunya., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High thermoelectric performance in crystallographically textured n-type Bi2Te3–xSex produced from asymmetric colloidal nanocrystals

  • Liu, Yu
  • Lim, Khak Ho
  • Ibáñez, María
  • Ortega, Silvia
  • Li, Mengyao
  • David, Jeremy
  • Martí-Sànchez, Sara
  • Ng, Ka Ming
  • Arbiol, Jordi
  • Kovalenko, Maksym V.
  • Cadavid, Doris
  • Cabot, Andreu
In the present work, we demonstrate crystallographically textured n-type Bi2Te3–xSex nanomaterials with exceptional thermoelectric figures of merit produced by consolidating disk-shaped Bi2Te3–xSex colloidal nanocrystals (NCs). Crystallographic texture was achieved by hot pressing the asymmetric NCs in the presence of an excess of tellurium. During the hot press, tellurium acted both as lubricant to facilitate the rotation of NCs lying close to normal to the pressure axis and as solvent to dissolve the NCs approximately aligned with the pressing direction, which afterward recrystallize with a preferential orientation. NC-based Bi2Te3–xSex nanomaterials showed very high electrical conductivities associated with large charge carrier concentrations, n. We hypothesize that such large n resulted from the presence of an excess of tellurium during processing, which introduced a high density of donor TeBi antisites. Additionally, the presence in between grains of traces of elemental Te, a narrow band gap semiconductor with a work function well below Bi2Te3–xSex, might further contribute to increase n through spillover of electrons, while at the same time blocking phonon propagation and hole transport through the nanomaterial. NC-based Bi2Te3–xSex nanomaterials were characterized by very low thermal conductivities in the pressing direction, which resulted in ZT values up to 1.31 at 438 K in this direction. This corresponds to a ca. 40% ZT enhancement from commercial ingots. Additionally, high ZT values were extended over wider temperature ranges due to reduced bipolar contribution to the Seebeck coefficient and the thermal conductivity. Average ZT values up to 1.15 over a wide temperature range, 320 to 500 K, were measured, which corresponds to a ca. 50% increase over commercial materials in the same temperature range. Contrary to most previous works, highest ZT values were obtained in the pressing direction, corresponding to the c crystallographic axis, due to the predominance of the thermal conductivity reduction over the electrical conductivity difference when comparing the two crystal directions., This work was supported by the European Regional Development Funds. Y.L. and Y.Z. thank the China Scholarship Council for scholarship support. M.V.K. acknowledges partial financial support by the European Union (EU) via FP7 ERC Starting Grant 2012 (Project NANOSOLID, GA no. 306733). S.M.S. acknowledges funding from “Programa Internacional de Becas “la Caixa”-Severo Ochoa”. J.D. acknowledges funding from the European Union’s Horizon 2020 research and innovation program under the Marie Sklodowska-Curie grant agreement no. 665919. ICN2 acknowledges funding from Generalitat de Catalunya 2017 SGR 327 and IREC from 2017 SGR 1246. ICN2 members acknowledge support from the Severo Ochoa Programme (MINECO, grant no. SEV-2013-0295) and is funded by the CERCA Programme/Generalitat de Catalunya. J.A., S.M.S., and J.D. acknowledge funding from MINECO subproject ANAPHASE (ENE2017-85087-C3)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Optimizing the yield of A-polar GaAs nanowires to achieve defect-free zinc blende structure and enhanced optical functionality

  • Zamani, Mahdi
  • Tütüncüoglu, Gözde
  • Martí-Sànchez, Sara
  • Francaviglia, Luca
  • Güniat, Lucas
  • Ghisalberti, Lea
  • Potts, Heidi
  • Friedl, Martin
  • Markov, Edoardo
  • Kim, Wonjong
  • Leran, Jean-Baptiste
  • Dubrovskii, Vladimir G.
  • Arbiol, Jordi
  • Fontcuberta i Morral, Anna
Compound semiconductors exhibit an intrinsic polarity, as a consequence of the ionicity of their bonds. Nanowires grow mostly along the (111) direction for energetic reasons. Arsenide and phosphide nanowires grow along (111)B, implying a group V termination of the (111) bilayers. Polarity engineering provides an additional pathway to modulate the structural and optical properties of semiconductor nanowires. In this work, we demonstrate for the first time the growth of Ga-assisted GaAs nanowires with (111)A-polarity, with a yield of up to ∼50%. This goal is achieved by employing highly Ga-rich conditions which enable proper engineering of the energies of A and B-polar surfaces. We also show that A-polarity growth suppresses the stacking disorder along the growth axis. This results in improved optical properties, including the formation of AlGaAs quantum dots with two orders or magnitude higher brightness. Overall, this work provides new grounds for the engineering of nanowire growth directions, crystal quality and optical functionality., The funding for this research was provided by Swiss National Science Foundation (SNSF), National Centre of Competence in Research Quantum Science and Technology (NCCR QSIT) and Horizon 2020 European Union Funding for Research and Innovation through projects INDEED and LIMQUET. SMS acknowledges funding from “Programa Internacional de Becas “la Caixa”-Severo Ochoa”. SMS and JA acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO ENE2017-85087-C3-3-R project. ICN2 acknowledges support from the Severo Ochoa Program (MINECO, Grant SEV-2013-0295) and is funded by the CERCA Programme/Generalitat de Catalunya. This work has received funding from the European Union's Horizon 2020 Research and Innovation Programme under grant agreement No. 654360 NFFA-Europe. VGD thanks the Russian Foundation for Basic Research for financial support under grants 17-52-16017, 16-29-03129, 16-02-00134, 16-29-03283, and 18-02-40006., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Reduction of thermal conductivity in nanowires by combined engineering of crystal phase and isotope disorder

  • Mukherjee, Samik
  • Givan, U.
  • Senz, S.
  • Mata, Maria de la
  • Arbiol, Jordi
  • Moutanabbir, Oussama
Nanowires are a versatile platform to investigate and harness phonon and thermal transport phenomena in nanoscale systems. With this perspective, we demonstrate herein the use of crystal phase and mass disorder as effective degrees of freedom to manipulate the behavior of phonons and control the flow of local heat in silicon nanowires. The investigated nanowires consist of isotopically pure and isotopically mixed nanowires bearing either a pure diamond cubic or a cubic-rhombohedral polytypic crystal phase. The nanowires with tailor-made isotopic compositions were grown using isotopically enriched silane precursors 28SiH4, 29SiH4, and 30SiH4 with purities better than 99.9%. The analysis of polytypic nanowires revealed ordered and modulated inclusions of lamellar rhombohedral silicon phases toward the center in otherwise diamond-cubic lattice with negligible interphase biaxial strain. Raman nanothermometry was employed to investigate the rate at which the local temperature of single suspended nanowires evolves in response to locally generated heat. Our analysis shows that the lattice thermal conductivity in nanowires can be tuned over a broad range by combining the effects of isotope disorder and the nature and degree of polytypism on phonon scattering. We found that the thermal conductivity can be reduced by up to ∼40% relative to that of isotopically pure nanowires, with the lowest value being recorded for the rhombohedral phase in isotopically mixed 28Six30Si1–x nanowires with composition close to the highest mass disorder (x ∼ 0.5). These results shed new light on the fundamentals of nanoscale thermal transport and lay the groundwork to design innovative phononic devices., O.M. acknowledges support from NSERC-Canada (Discovery Grants and Strategic Partnership Grants), the Canada Foundation for Innovation, MRIF Québec (Coopération Québec-Catalogne), Mitacs, and Canada Research Chair. J.A. acknowledges funding from Generalitat de Catalunya 2014 SGR 1638 and the Spanish MINECO coordinated projects VALPEC and ANAPHASE (ENE2017-85087-C3-3-R). ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant No. SEV-2013-0295) and is funded by the CERCA Programme/Generalitat de Catalunya., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

SnP nanocrystals as anode materials for Na-ion batteries

  • Liu, Junfeng
  • Wang, Shutao
  • Kravchyk, Kostiantyn
  • Ibáñez, María
  • Krumeich, Frank
  • Widmer, Roland
  • Nasiou, Déspina
  • Meyns, Michaela
  • Llorca, Jordi
  • Arbiol, Jordi
  • Kovalenko, Maksym V.
  • Cabot, Andreu
Tin monophosphide is a layered material consisting of Sn–P–P–Sn sandwiches that are stacked on top of each other to form a three dimensional crystallographic structure. Its composition and crystal structure makes it an excellent candidate anode material for sodium-ion batteries (SIBs). However, SnP is yet to be explored for such and other applications due to its challenging synthesis. In the present work, we report the synthesis of SnP nanocrystals (NCs) from the reaction of hexamethylphosphorous triamide (HMPT) and a tin phosphonate prepared from tin oxalate and a long chain phosphonic acid. SnP NCs obtained from this reaction displayed a spherical geometry and a trigonal crystallographic phase with a superstructure attributed to ordered diphosphorus pairs. Such NCs were mixed with carbon black and used as anode materials in SIBs. SIBs based on SnP NCs and sodium(I) bis(fluorosulfonyl)imide (NaFSI) electrolyte displayed a high reversible capacity of 600 mA h g−1 at a current density of 100 mA g−1 and cycling stability for over 200 cycles. Their excellent cycling performance is associated with both the small size of the crystal domains and the particular composition and phase of SnP which prevent mechanical disintegration and major phase separation during sodiation and desodiation cycles. These results demonstrate SnP to be an attractive anode material for sodium ion batteries., DN and JA acknowledge funding from Generalitat de Catalunya 2014 SGR 1638 and the Spanish MINECO projects VALPEC and ANAPHASE (ENE2017-85087-C3-3-R). The ICN2 acknowledges support from the Severo Ochoa Programme (SEV-2013-0295) and is funded by Generalitat de Catalunya. JL thanks the China Scholarship Council for scholarship support. MM acknowledges a Juan de la Cierva formación grant by the Spanish MINECO. JLl is a Serra Húnter Fellow and is grateful to ICREA Academia program and projects MINECO/FEDER ENE2015-63969-R and GC 2017 SGR 128., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Triphenyl phosphite as the phosphorus source for the scalable and cost-effective production of transition metal phosphides

  • Liu, Junfeng
  • Meyns, Michaela
  • Zhang, Ting
  • Arbiol, Jordi
  • Cabot, Andreu
  • Shavel, Alexey
Transition metal phosphides have great potential to optimize a number of functionalities in several energy conversion and storage applications, particularly when nanostructured or in nanoparticle form. However, the synthesis of transition metal phosphide nanoparticles and its scalability is often limited by the toxicity, air sensitivity, and high cost of the reagents used. We present here a simple, scalable, and cost-effective “heating up” procedure to produce metal phosphides using inexpensive, low-toxicity, and air-stable triphenyl phosphite as source of phosphorus and chlorides as metal precursors. This procedure allows the synthesis of a variety of phosphide nanoparticles, including phosphides of Ni, Co, and Cu. The use of carbonyl metal precursors further allowed the synthesis of Fe2P and MoP nanoparticles. The fact that minor modifications in the experimental parameters allowed producing nanoparticles with different compositions and even to tune their size and shape shows the high potential and versatility of the triphenyl phosphite precursor and the presented method. We also detail here a methodology to displace organic ligands from the surface of phosphide nanoparticles, which is a key step toward their application in energy conversion and storage systems., This work was supported by the European Regional Development Funds and the Spanish Ministerio de Economia y Competitividad through the project SEHTOP (ENE2016-77798-C4-3-R). J.L. thanks the China Scholarship Council for scholarship support. M.M. thanks the Spanish MINECO for her Juan de la Cierva scholarship. T.Z. and J.A. acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO coordinated project ANAPHASE (ENE2017-85087-C3-3-R). ICN2 acknowledges support from the Severo Ochoa Programme (MINECO, Grant no. SEV2013-0295) and is funded by the CERCA Programme/ Generalitat de Catalunya. T.Z. has received funding from the CSC-UAB PhD scholarship program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Tailoring copper foam with silver dendrite catalysts for highly selective carbon dioxide conversion into carbon monoxide

  • Urbain, Félix
  • Tang, Peng-Yi
  • Carretero, Nina M.
  • Andreu, Teresa
  • Arbiol, Jordi
  • Morante, Joan Ramón
The present study outlines the important steps to bring electrochemical conversion of carbon dioxide (CO2) closer to commercial viability by using a large-scale metallic foam electrode as a highly conductive catalyst scaffold. Because of its versatility, it was possible to specifically tailor three-dimensional copper foam through coating with silver dendrite catalysts by electrodeposition. The requirements of high-yield CO2 conversion to carbon monoxide (CO) were met by tuning the deposition parameters toward a homogeneous coverage of the copper foam with nanosized dendrites, which additionally featured crystallographic surface orientations favoring CO production. The presented results evidence that Ag dendrites, owing a high density of planes with stepped (220) surface sites, paired with the superior active surface area of the copper foam can significantly foster the CO productivity. In a continuous flow-cell reactor setup, CO Faradaic efficiencies reaching from 85 to 96% for a wide range of low applied cathode potentials (<1.0 VRHE) along with high CO current densities up to 27 mA/cm2 were achieved, far outperforming other tested scaffold materials. Overall, this research provides new strategic guidelines for the fabrication of efficient and versatile cathodes for CO2 conversion compatible with large-scale integrated prototype devices., Authors acknowledge funding from Generalitat de Catalunya through the CERCA program, 2017 SGR 1246, 2017 SGR 327 and the Spanish MINECO projects MAT2014-59961, ENE2016-80788-C5-5-R and ENE2017-85087, together with the support from REPSOL S.A. ICN2 acknowledges the support from the Severo Ochoa Programme (grant no. SEV2017-0706). F.U. acknowledges the financial support from MINECO through Juan de la Cierva fellowship (FJCI-2016-29147)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Multilayered hematite nanowires with thin‐film silicon photovoltaics in an all‐earth‐abundant hybrid tandem device for solar water splitting

  • Urbain, Félix
  • Tang, Peng-Yi
  • Smirnov, Vladimir
  • Welter, Katharina
  • Andreu, Teresa
  • Finger, Friedhelm
  • Arbiol, Jordi
  • Morante, Joan Ramón
The concept of hybrid tandem device structures that combine metal oxides with thin‐film semiconducting photoabsorbers holds great promise for large‐scale, robust, and cost‐effective bias‐free photoelectrochemical water splitting (PEC‐WS). This work highlights important steps toward the efficient coupling of high‐performance hematite photoanodes with multijunction thin‐film silicon photocathodes providing high bias‐free photocurrent density. The hybrid PEC‐WS device is optimized by testing three types of multijunction silicon photocathodes with the hematite photoanode: amorphous silicon (a‐Si:H) tandem: a‐Si:H/a‐Si:H and triple junction with microcrystalline silicon (μc‐Si:H): a‐Si:H/a‐Si:H/μc‐Si:H and a‐Si:H/μc‐Si:H/μc‐Si:H. The results provide evidence that the multijunction structures offer high flexibility for hybrid tandem devices with regard to tunable photovoltages and spectral matching. Furthermore, both photoanode and photocathode are tested under various electrolyte and light concentration conditions, respectively, with respect to their photoelectrochemical performance and stability. A 27 % enhancement in the solar‐to‐hydrogen conversion efficiency is observed upon concentrating light from 100 to 300 mW cm−2. Ultimately, bias‐free water splitting is demonstrated, with a photocurrent density of 4.6 mA cm−2 (under concentrated illumination) paired with excellent operation stability for more than 24 h of the all‐earth‐abundant and low‐cost hematite/silicon tandem PEC‐WS device., The authors acknowledge funding from Generalitat de Catalunya through the CERCA program, 2017 SGR 1246, 2017 SGR 327 and the Spanish MINECO projects MAT2014‐59961, ENE2016‐80788‐C5‐5‐R and ENE2017‐85087, together with the support from REPSOL, S. A. ICN2 is supported by the Severo Ochoa program from Spanish MINECO (Grant No. SEV‐2017‐0706). IREC also acknowledges additional support from the European Regional Development Funds (ERDF, FEDER), (S)TEM part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program and the rest in the Nanoscience program of the University of Barcelona. The authors thank S. Moll (IEK‐5), M. Biset‐Peiró (IREC), and H. Xie (IREC) for their contribution to this work. F.U. acknowledges financial support from MINECO through Juan de la Cierva fellowship (FJCI‐2016–29147).V.S., K.W., and F.F. (authors from IEK‐5) thank the Deutsche Forschungsgemeinschaft (DFG) (Priority Program SPP 1613)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Upscaling high activity oxygen evolution catalysts based on CoFe2O4 nanoparticles supported on nickel foam for power-to-gas electrochemical conversion with energy efficiencies above 80%

  • Urbain, Félix
  • Du, Ruifeng
  • Tang, Peng-Yi
  • Smirnov, Vladimir
  • Andreu, Teresa
  • Finger, Friedhelm
  • Divins, Núria J.
  • Llorca, Jordi
  • Arbiol, Jordi
  • Cabot, Andreu
  • Morante, Joan Ramón
We investigate cobalt ferrite nanoparticles (NPs) supported on large-scale electrodes as oxygen evolution reaction (OER) catalysts. Colloidal CoFe2O4 NPs were loaded on low-cost and high surface area nickel foam (NF) scaffolds. The coating process was optimized for large electrode areas, ensuring a proper distribution of the NPs on the NF that allowed overcoming the electrical conductivity limitations of oxide NPs. We were able to produce CoFe2O4-coated NFs having 10 cm2 geometric surface areas with overpotentials below 300 mV for the OER at a current density of 50 mA/cm2. Such impressively low overpotentials suggested using CoFe2O4 NP-based electrodes within a water electrolysis device. In this prototype device, stable operating currents up to 500 mA at remarkably low cell-voltages of 1.62 and 1.53 V, at ambient and 50 °C electrolyte temperatures, respectively, were reached during operation periods of up to 50 h. The high electrochemical energy efficiencies reached at 50 mA/cm2, 75% and 81% respectively, rendered these devices particularly appealing to be combined with low-cost photovoltaic systems for bias-free hydrogen production. Therefore, CoFe2O4 NP-based electrolysers were coupled to low-cost thin-film silicon solar cells with 13% efficiency to complete a system that afforded solar-to-fuel efficiencies above 10%., Authors acknowledge funding from Generalitat de Catalunya through the CERCA program, 2017 SGR 1246, 2017 SGR 327 and the Spanish MINECO projects MAT2014-59961, ENE2016-80788-C5-5-R, ENE2016-77798-C4-3-R and ENE2017-85087, together with the support from Repsol S. A. Likewise, the authors thank Enagás S.A. ICN2 is supported by the Severo Ochoa program from Spanish MINECO (Grant No. SEV-2017-0706). IREC also acknowledges additional support from the European Regional Development Funds (ERDF, FEDER), (S)TEM part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program and the rest in the Nanoscience program of the University of Barcelona. The authors thank S. Moll (IEK-5), M. Biset-Peiró (IREC), and H. Xie (IREC) for their contribution to this work. F.U. acknowledges financial support from MINECO through Juan de la Cierva fellowship (FJCI-2016-29147).V.S. and F.F. (authors from IEK-5) thank the Deutsche Forschungsgemeinschaft (DFG) (Priority Program SPP 1613). J. Llorca is a Serra Húnter Fellow and is grateful to ICREA Academia program and funding from Generalitat de Catalunya 2017 SGR 128., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High magnetic coercivity in nanostructured Mn3O4 thin films obtained by chemical vapor deposition

  • Bigiani, Lorenzo
  • Hassan, Marian
  • Peddis, Davide
  • Maccato, Chiara
  • Varvaro, Gaspare
  • Sada, Cinzia
  • Bontempi, Elza
  • Martí-Sànchez, Sara
  • Arbiol, Jordi
  • Barreca, Davide
Nanostructured α-Mn3O4 (haussmannite) thin films consisting of evenly interconnected nanoaggregates were prepared on Si(100) substrates by chemical vapor deposition from a Mn(II) diketonate-diamine precursor under different reaction atmospheres (dry vs wet O2) and total operating pressures. The combination of chemico-physical results obtained by the joint use of complementary techniques enabled us to demonstrate the obtainment of high-purity Mn3O4 materials free from other manganese oxide phases, characterized by controllable structural and morphological characteristics as a function of the adopted processing conditions. Magnetic properties were investigated by analyzing temperature dependence (i.e., field-cooled and zero-field-cooled measurements) and field-dependence of the magnetization behavior. The obtained films show bulk-like magnetic properties, together with extraordinarily high low-temperature in-plane coercivities (up to ∼1 T). The possibility to tailor these values by varying the content of microstructural defects may foster the implementation of the obtained films in eventual technological applications., The authors thank Padova University DOR 2016–2018 and P-DiSC #03BIRD2016-UNIPD projects. Funding from Generalitat de Catalunya 2017 SGR 327, the Spanish MINECO ENE2017-85087-C3-3-R, and Severo Ochoa Program SEV-2017-0706, as well as CERCA Programme/Generalitat de Catalunya is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Atomic atom distribution of Ruthenium dispersed on a 2D covalent organic framework for electrocatalytic hydrogen evolution reaction

  • Liang, Zhifu
  • Wang, Xiang
  • Cabot, Andreu
  • Arbiol, Jordi
Resumen del póster presentado al nanoGe Fall Meeting, celebrado en Berlín (Alemania) del 4 al 8 de noviembre de 2019., In recent years, Single-atom catalysis (SAC) has become one of the most research hot topics in heterogeneous catalysis. As it is known, both homogeneous and heterogeneous catalysts are important for the reactions used in chemical industry. In homogeneous catalysis, up to 100% of the atoms may remain active during reactions, while for the in the case of heterogeneous catalysts, only a small fraction of the metal atoms can be utilized due to the aggregation of the atoms when forming clusters. In this way, SACs have the benefits of homogeneous and heterogeneous catalysts. In our case, we will use a 2D covalent organic framework (COF), which is a π-conjugated microporous polymer with a high stability, designability and crystallinity. In addition, contains a high number of pyridinic nitrogen which will not only be used for anchoring the metal atoms, but also as an active site for the catalytic reaction. Here we propose a single atom ruthenium catalysts on a 2D COF for improved electrocatalytic hydrogen evolution reaction., This work was supported by the European Regional Development Fund and by the Spanish Ministerio de Ciencia, Innovación y Universidades through the project SEHTOP (ENE 2016-77798-C4-3-R). This poster is funded by FEDER/Ministerio de Ciencia, Innovación y Universidades – Agencia Estatal de Investigación (ENE2017-85087-C3-3-R). Z.Liang. are grateful for financial support from Severo Ochoa Fellowship SEV-2013-0295. W Xiang and D Yang. thanks the China Scholarship Council. ICN2 is supported by the Severo Ochoa programme funded by AEI (Grant no. SEV-2017-0706) and is funded by the CERCA Programme/Generalitat de Catalunya., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Combined high catalytic activity and efficient polar tubular nanostructure in urchin-like metallic NiCo2Se4 for high-performance lithium–sulfur batteries

  • Zhang, Ting
  • Zhang, Chaoqi
  • Jacas Biendicho, Jordi
  • Yang, Xuhui
  • Zhou, Yingtang
  • Morante, Joan Ramón
  • Cabot, Andreu
  • Arbiol, Jordi
Resumen del póster presentado al nanoGe Fall Meeting, celebrado en Berlín (Alemania) del 4 al 8 de noviembre de 2019., To realize fast-growing field of electric vehicles, rechargeable lithium-sulfur batteries (LSBs) have recently emerged as one of the most exciting alternatives to lithium-ion batteries (LIBs) owing to their higher theoretical energy density, 6 times higher than LIBs and lower cost. However, a poor utilization of the active material involved by the electrical insulating character of sulfur and lithium sulfides and a rapid degradation during charge/discharge processes still limit their practical application. Therefore, in this work, an urchin-shaped NiCo2Se4 (u-NCSe) nanostructures as efficient sulfur hosts were synthesized to overcome the limitations of lithium-sulfur batteries (LSBs) using selenization of Ni0.33Co0.67(CO3)0.5OH precursor. The u-NCSe showed a hollow structure with different distribution of Ni, Co and Se, which was proved by electron energy loss spectroscopy (EELS). Meanwhile, the high-resolution transmission electron microscopy (HRTEM) images indicated that the NiCo2Se4 nanostructures had a good crystallinity, in agreement with the cubic phase of NiCo2Se4 (space group: C12/m1). Owing to the hollow structure that can relieve volumetric expansion, a superior electrical conductivity to improve electron transfer, a high polarity to promote absorption of lithium polysulfides (LiPS), and outstanding electrocatalytic activity to accelerate LiPS conversion kinetics, S@u-NCSe delivers outstanding initial capacities up to 1403 mAh/g at 0.1 C and retains 626 mAh/g at 5 C with exceptional rate performance. More significantly, a very low capacity decay rate of only 0.016% per cycle is obtained after 2000 cycles at 3 C. Even at high sulfur loading (3.2 mg/cm2), a reversible capacity of 557 mAh/g is delivered after 600 cycles at 1 C. Density functional theory calculations further confirm the strong interaction between NCSe and LiPS, and cytotoxicity measure-ments prove the biocompatibility of NCSe. This work not only demonstrates that transition metal selenides can be promising candidates as sulfur host materials, but also provides a strategy for the rational design and the development of LSBs with long-life and high-rate electrochemical performance., This work corresponds to an extension of activities initially performed around the objectives defined by the Helis project which received funding from the European Union’s Horizon 2020 program under the Grant Agreement No. 666221. The authors acknowledge funding from Generalitat de Catalunya2017 SGR 1246 and 2017 SGR 327, the Spanish MINECO projects ENE2016-77798-C4-3-R and ENE2017-85087-C3, and the Zhou Shan Science and Technology Project (2018C21010). C. Zhang and T. Zhang thank the China Scholarship Council (CSC) for scholarship support. IREC acknowledges funding from European Regional Development Funds (ERDF-FEDER Programa Competitivitat de Catalunya 2007–2013). ICN2 was supported by the Severo Ochoa program from Spanish MINECO (Grant No. SEV-2017-0706) and was funded by the CERCA Programme/Generalitat de Catalunya. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science Ph.D. program. This poster is funded by FEDER/Ministerio de Ciencia, Innovación y Universidades – Agencia Estatal de Investigación (ENE2017-85087-C3-3-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

SnS2/g-C3N4/graphite nanocomposites as durable lithium-ion battery anode with high pseudocapacitance contribution

  • Zuo, Yong
  • Xu, Xijun
  • Zhang, Chaoqi
  • Li, Junshan
  • Du, Ruifeng
  • Wang, Xiang
  • Han, Xu
  • Arbiol, Jordi
  • Llorca, Jordi
  • Liu, Jun
  • Cabot, Andreu
Tin disulfide is a promising anode material for Li-ion batteries (LIB) owing to its high theoretical capacity and the abundance of its composing elements. However, bare SnS2 suffers from low electrical conductivity and large volume expansion, which results in poor rate performance and cycling stability. Herein, we present a solution-based strategy to grow SnS2 nanostructures within a matrix of porous g-C3N4 (CN) and high electrical conductivity graphite plates (GPs). We test the resulting nanocomposite as anode in LIBs. First, SnS2 nanostructures with different geometries are tested, to find out that thin SnS2 nanoplates (SnS2-NPLs) provide the highest performances. Such SnS2-NPLs, incorporated into hierarchical SnS2/CN/GP nanocomposites, display excellent rate capabilities (536.5 mA h g−1 at 2.0 A g−1) and an outstanding stability (∼99.7% retention after 400 cycles), which are partially associated with a high pseudocapacitance contribution (88.8% at 1.0 mV s−1). The excellent electrochemical properties of these nanocomposites are ascribed to the synergy created between the three nanocomposite components: i) thin SnS2-NPLs provide a large surface for rapid Li-ion intercalation and a proper geometry to stand volume expansions during lithiation/delithiation cycles; ii) porous CN prevents SnS2-NPLs aggregation, habilitates efficient channels for Li-ion diffusion and buffer stresses associated to SnS2 volume changes; and iii) conductive GPs allow an efficient charge transport., This work was supported by the European Regional Development Funds and by the Spanish Ministerio de Economía y Competitividad through the project SEHTOP (ENE2016-77798-C4-3-R). Y.Z. thanks China Scholarship Council for scholarship support (201606500001). This work was accomplished with the financial supported from the National Natural Science Foundation of China (no. 51771076) and (no. 51621001. the Foundation for Innovative Research Groups). Jun Liu acknowledges the support from Chinese Government the young “1000 plan”, and thanks the projects of Guangzhou Science and Technology Plan (no. 201804010104) and Guangdong Province Public Interest Research and Capacity Building (no. 2017A010104004). Jordi Llorca is a Serra Húnter Fellow and is grateful to ICREA Academia program and GC 2017 SGR 128. X.H. thanks China Scholarship Council for scholarship support (201804910551). ICN2 acknowledge funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO project ENE2017-85087-C3-3-R. ICN2 is supported by the Severo Ochoa program from Spanish MINECO (Grant No. SEV-2017-0706) and is funded by the CERCA Programme /Generalitat de Catalunya. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of the Annealing Atmosphere on Crystal Phase and Thermoelectric Properties of Copper Sulfide

  • Li, Mengyao
  • Liu, Yu
  • Zhang, Yu
  • Han, Xu
  • Zhang, Ting
  • Zuo, Yong
  • Xie, Chenyang
  • Xiao, Ke
  • Arbiol, Jordi
  • Llorca, Jordi
  • Ibáñez, María
  • Liu, Junfeng
  • Cabot, Andreu
Cu2-xS has become one of the most promising thermoelectric materials for application in the middle-high temperature range. Its advantages include the abundance, low cost, and safety of its elements and a high performance at relatively elevated temperatures. However, stability issues limit its operation current and temperature, thus calling for the optimization of the material performance in the middle temperature range. Here, we present a synthetic protocol for large scale production of covellite CuS nanoparticles at ambient temperature and atmosphere, and using water as a solvent. The crystal phase and stoichiometry of the particles are afterward tuned through an annealing process at a moderate temperature under inert or reducing atmosphere. While annealing under argon results in Cu1.8S nanopowder with a rhombohedral crystal phase, annealing in an atmosphere containing hydrogen leads to tetragonal Cu1.96S. High temperature X-ray diffraction analysis shows the material annealed in argon to transform to the cubic phase at ca. 400 K, while the material annealed in the presence of hydrogen undergoes two phase transitions, first to hexagonal and then to the cubic structure. The annealing atmosphere, temperature, and time allow adjustment of the density of copper vacancies and thus tuning of the charge carrier concentration and material transport properties. In this direction, the material annealed under Ar is characterized by higher electrical conductivities but lower Seebeck coefficients than the material annealed in the presence of hydrogen. By optimizing the charge carrier concentration through the annealing time, Cu2-xS with record figures of merit in the middle temperature range, up to 1.41 at 710 K, is obtained. We finally demonstrate that this strategy, based on a low-cost and scalable solution synthesis process, is also suitable for the production of high performance Cu2-xS layers using high throughput and cost-effective printing technologies., This work was supported by the European Regional Development Funds. M.Y.L., X.H., T.Z., and K.X. thank the China Scholarship Council for scholarship support. M.I. acknowledges financial support from IST Austria. J.L. acknowledges support from the National Natural Science Foundation of China (No. 22008091), the funding for scientific research startup of Jiangsu University (No. 19JDG044), and Jiangsu Provincial Program for High-Level Innovative and Entrepreneurial Talents Introduction. J.L. is a Serra Húnter fellow and is grateful to the ICREA Academia program and projects MICINN/FEDER RTI2018-093996-B-C31 and GC 2017 SGR 128. ICN2 acknowledges funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO ENE2017-85087-C3. ICN2 is supported by the Severo Ochoa program from Spanish MINECO (Grant No. SEV-2017-0706) and is funded by the CERCA Programme/Generalitat de Catalunya. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program. T.Z. has received funding from the CSC-UAB PhD scholarship program.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effects of solar irradiation on thermally driven CO2 methanation using Ni/CeO2–based catalyst

  • Golovanova, Viktoria
  • Spadaro, Maria Chiara
  • Arbiol, Jordi
  • Golovanova, Liubov V.
  • Rantala, Tapio T.
  • Andreu, Teresa
  • Morante, Joan Ramón
Utilization of the renewable energy sources is one of the main challenges in the state-of-the-art technologies for CO recycling. Here we have taken advantage of the solar light harvesting in the thermocatalytic approach to carbon dioxide methanation. The large-surface-area Ni/CeO catalyst produced by a scalable low-cost method was characterized and tested in the dark and under solar light irradiation conditions. Light-assisted CO conversion experiments as well as in-situ DRIFT spectrometry, performed at different illumination intensities, have revealed a dual effect of the incident photons on the catalytic properties of the two-component Ni/CeO catalyst. On the one hand, absorbed photons induce a localized surface plasmon resonance in the Ni nanoparticles followed by dissipation of the heat to the oxide matrix. On the other hand, the illumination activates the photocatalytic properties of the CeO support, which leads to an increase in the concentration of the intermediates being precursor for methane production. Analysis of the methane production at different temperatures and illumination conditions has shown that the methanation reaction in our case is controlled by a photothermally-activated process. The used approach has allowed us to increase the reaction rate up to 2.4 times and consequently to decrease the power consumption by 20 % under solar illumination, thus replacing the conventional thermal activation of the reaction with a green energy source., This work has been done in the framework of the doctorate programme in Materials Science of the Autonomous University of Barcelona. V. Golovanova has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 754397. Authors acknowledge Generalitat de Catalunya for financial support through the CERCA Programme, M2E (2017 SGR 1246) and the CSC – IT Center for Science, Espoo, Finland for provided resources. IREC also acknowledges additional support by the European Regional Development Funds (ERDF, FEDER) and by MINECO coordinated projects MAT2014-59961-C2, ENE2016-80788-C5-5-R and ENE2017-85087-C3. M. C. Spadaro and J. Arbiol acknowledge funding from Generalitat de Catalunya 2017 SGR 327. ICN2 is supported by the Severo Ochoa programme from Spanish MINECO (Grant No. SEV-2017-0706) and is funded by the CERCA Programme / Generalitat de Catalunya. M. C. Spadaro has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 754510 (PROBIST) and the Severo Ochoa programme.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhanced thermoelectric performance of n-type bi2se3 nanosheets through sn doping

  • Li, Mengyao
  • Zhang, Yu
  • Zhang, Ting
  • Zuo, Yong
  • Xiao, Ke
  • Arbiol, Jordi
  • Llorca, Jordi
  • Liu, Yu
  • Cabot, Andreu
The cost-effective conversion of low-grade heat into electricity using thermoelectric devices requires developing alternative materials and material processing technologies able to reduce the currently high device manufacturing costs. In this direction, thermoelectric materials that do not rely on rare or toxic elements such as tellurium or lead need to be produced using high-throughput technologies not involving high temperatures and long processes. BiSe is an obvious possible Tefree alternative to BiTe for ambient temperature thermoelectric applications, but its performance is still low for practical applications, and additional efforts toward finding proper dopants are required. Here, we report a scalable method to produce BiSe nanosheets at low synthesis temperatures. We studied the influence of different dopants on the thermoelectric properties of this material. Among the elements tested, we demonstrated that Sn doping resulted in the best performance. Sn incorporation resulted in a significant improvement to the BiSe Seebeck coefficient and a reduction in the thermal conductivity in the direction of the hot-press axis, resulting in an overall 60% improvement in the thermoelectric figure of merit of BiSe ., M.L., Y.Z., T.Z. and K.X. thank the China Scholarship Council for their scholarship support. Y.L. acknowledges funding from the European Union’s Horizon 2020 research and innovation program under the Marie Sklodowska-Curie grant agreement No. 754411. J.L. thanks the ICREA Academia program and projects MICINN/FEDER RTI2018-093996-B-C31 and G.C. 2017 SGR 128. ICN2 acknowledges funding from the Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO ENE2017-85087-C3.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Photodehydrogenation of ethanol over cu2o/tio2 heterostructures

  • Xing, Congcong
  • Zhang, Yu
  • Liu, Yongpeng
  • Wang, Xiang
  • Li, Junshan
  • Martínez-Alanis, Paulina R.
  • Spadaro, Maria Chiara
  • Guardia, Pablo
  • Arbiol, Jordi
  • Llorca, Jordi
  • Cabot, Andreu
The photodehydrogenation of ethanol is a sustainable and potentially cost-effective strategy to produce hydrogen and acetaldehyde from renewable resources. The optimization of this process requires the use of highly active, stable and selective photocatalytic materials based on abundant elements and the proper adjustment of the reaction conditions, including temperature. In this work, CuO-TiO type-II heterojunctions with different CuO amounts are obtained by a one-pot hydrothermal method. The structural and chemical properties of the produced materials and their activity toward ethanol photodehydrogenation under UV and visible light illumination are evaluated. The CuO-TiO photocatalysts exhibit a high selectivity toward acetaldehyde production and up to tenfold higher hydrogen evolution rates compared to bare TiO . We further discern here the influence of temperature and visible light absorption on the photocatalytic performance. Our results point toward the combination of energy sources in thermo-photocatalytic reactors as an efficient strategy for solar energy conversion., This work was supported by the MINECO project COMBENERGY (PID2019-105490RB-C32) and MICINN/FEDER project RTI2018-093996-B-C31. J.A. and M.C.S. thank funding from GC 2017 SGR 327 and MINECO project (ENE2017-85087-C3). ICN2 thanks supporting from the Severo Ochoa Program (MINECO, No. SEV-2013-0295) and the CERCA Program/Generalitat de Catalunya. Y.Z., C.X., and X.W. acknowledge the China Scholarship Council (CSC) for scholarship support. Part of the present work has been performed in the framework of Universitat Autònoma de Barcelona Materials Science PhD program. J.L. is a Serra Hunter fellow and is grateful to GC 2017 SGR 128 and ICREA Academia program. Y.L. thank the Swiss National Science Foundation (SNF) for funding under the Ambizione Energy (No. PZENP2_166871). M.C.S. has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 754510 (PROBIST) and the Severo Ochoa programme.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enabling full-scale grain boundary mitigation in polycrystalline perovskite solids

  • Zhao, Lichen
  • Tang, Peng-Yi
  • Luo, Deying
  • Dar, M. Ibrahim
  • Eickemeyer, Félix T.
  • Arora, Neha
  • Hu, Qin
  • Luo, Jingshan
  • Liu, Yuhang
  • Zakeeruddin, Shaik Mohammed
  • Hagfeldt, Anders
  • Arbiol, Jordi
  • Huang, Wei
  • Gong, Qihuang
  • Russell, Thomas P.
  • Friend, Richard H.
  • Grätzel, Michael
  • Zhu, Rui
There exists a considerable density of interaggregate grain boundaries (GBs) and intra-aggregate GBs in polycrystalline perovskites. Mitigation of intra-aggregate GBs is equally notable to that of interaggregate GBs as intra-aggregate GBs can also cause detrimental effects on the photovoltaic performances of perovskite solar cells (PSCs). Here, we demonstrate full-scale GB mitigation ranging from nanoscale intra-aggregate to submicron-scale interaggregate GBs, by modulating the crystallization kinetics using a judiciously designed brominated arylamine trimer. The optimized GB-mitigated perovskite films exhibit reduced nonradiative recombination, and their corresponding mesostructured PSCs show substantially enhanced device efficiency and long-term stability under illumination, humidity, or heat stress. The versatility of our strategy is also verified upon applying it to different categories of PSCs. Our discovery not only specifies a rarely addressed perspective concerning fundamental studies of perovskites at nanoscale but also opens a route to obtain high-quality solution-processed polycrystalline perovskites for high-performance optoelectronic devices., This work was financially supported by Beijing Natural Science Foundation (JQ21005), the National Key R&D Program of China (2021YFB3800100 and 2021YFB3800101), the National Natural Science Foundation of China (91733301 and 62104221), the China Postdoctoral Science Foundation (2020M670036), and the R&D Fruit Fund (20210001). M.G. and S.M.Z. thank the King Abdulaziz City for Science and Technology (KACST) for financial support. M.I.D. acknowledges funding from the Royal Society. N.A. and R.H.F. thank the EPSRC project SUNRISE (EP/P032591/1). Q.H. and T.P.R. were supported by the U.S. Office of Naval Research under contract N00014-17-1-2241. Q.H. thanks the support from USTC Research funds of the Double First-Class Initiative (YD2100002007). We thank the support for sample preparation at Molecular Foundry of Lawrence Berkeley National Laboratory (LBNL), which is supported by the Office of Science, Office of Basic Energy Sciences, of the U.S. Department of Energy under contract no. DE-AC02-05CH11231. We also acknowledge the GIXD measurements at beamline 7.3.3 of Advanced Light Source (LBNL), which is a DOE Office of Science User Facility under contract no. DE-AC02-05CH11231. P.T. and J.A. acknowledge the funding from Generalitat de Catalunya 2017 SGR 327 and the Spanish MINECO project ENE2017-85087-C3. ICN2 is supported by the Severo Ochoa program from Spanish MINECO (grant no. SEV-2017-0706) and is funded by the CERCA Programme/Generalitat de Catalunya.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

FeS2-Decorated Carbon NanoFiber as Solid Phase Conversion-Type Cathode for Li-S Batteries

  • Jacas Biendicho, Jordi
  • Mazaira, Pedro
  • Avireddy, Hemesh
  • Zhang, Chaoqi
  • Tang, Peng-Yi
  • Missyul, Alexander
  • Trilla, Lluis
  • Arbiol, Jordi
  • Morante, Joan Ramón
  • Cabot, Andreu
A new cathode material, FeS2-decorated carbon nanofiber (CNF), is proposed for Li-S batteries. The structure and physicochemical properties of the material have been engineered to enhance the poor cycling stability typically displayed by sulfur composites. The composite material shows a complex architecture with a matrix of CNF hosting the sulfur and core-shell FeS2 nanoparticles acting as a catalyst for a solid phase conversion-type reaction. This cathode delivers high discharge capacities of 864, 798, 689, 595 and 455 mAhg−1 at C/10, C/5, C/2, 1C and 2C, respectively, with a stable capacity retention of 87% at 2C after 300 cycles. FeS2-decorated CNF has been characterised using several techniques, including in-situ battery measurements at the ALBA synchrotron facility and high-throughput microscopy, giving valuable insights into its charge/discharge reaction mechanism. The excellent performance obtained is combined with the use of just low-cost and abundant elements such as iron, sulfur and carbon, which makes this battery highly promising for the next generation of electrochemical energy storage devices., The authors acknowledge funding from Generalitat de Catalunya 2021 SGR 01581 and 2021 SGR 00457 the Spanish MINECO project ENE2017-85087-C3. IREC and ICN2 are funded by the CERCA Programme/Generalitat de Catalunya. The authors thank support from the project NANOGEN (PID2020-116093RB-C43), funded by MCIN/AEI/10.13039/501100011033/ and by “ERDF A way of making Europe”, by the “European Union”. This study was supported by MCIN with funding from European Union NextGenerationEU (PRTR-C17.I1) and Generalitat de Catalunya. ICN2 is supported by the Severo Ochoa program from Spanish MCIN/AEIN (Grant No.: CEX2021-001214-S). IREC acknowledges additional support from the European Regional Development Funds (ERDF, FEDER). Jordi Jacas Biendicho acknowledges the fellowship RYC2021-034994-I, funded by MCIN/AEI/10.13039/501100011033 and the European Union «NextGenerationEU»/PRTR». In-situ diffraction measurements experiments were performed at BL04-MSPD beamline at ALBA Synchrotron with the collaboration of ALBA staff under proposal number 2016091931., With funding from the Spanish government through the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2021-001214-S), Peer reviewed
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Triphenyl phosphite as the phosphorus source for the scalable and cost-effective production of transition metal phosphides

  • Liu, Junfeng|||0000-0003-3164-6472
  • Meyns, Michaela|||0000-0003-2476-9001
  • Zhang, Ting|||0000-0002-0317-9662
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
  • Shavel, Alexey|||0000-0002-3995-0391
Transition metal phosphides have great potential to optimize a number of functionalities in several energy conversion and storage applications, particularly when nanostructured or in nanoparticle form. However, the synthesis of transition metal phosphide nanoparticles and its scalability is often limited by the toxicity, air sensitivity, and high cost of the reagents used. We present here a simple, scalable, and cost-effective "heating up" procedure to produce metal phosphides using inexpensive, low-toxicity, and air-stable triphenyl phosphite as source of phosphorus and chlorides as metal precursors. This procedure allows the synthesis of a variety of phosphide nanoparticles, including phosphides of Ni, Co, and Cu. The use of carbonyl metal precursors further allowed the synthesis of FeP and MoP nanoparticles. The fact that minor modifications in the experimental parameters allowed producing nanoparticles with different compositions and even to tune their size and shape shows the high potential and versatility of the triphenyl phosphite precursor and the presented method. We also detail here a methodology to displace organic ligands from the surface of phosphide nanoparticles, which is a key step toward their application in energy conversion and storage systems.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Controllable vapor phase fabrication of F:Mn3O4 thin films functionalized with Ag and TiO2

  • Bigiani, Lorenzo|||0000-0001-7404-2340
  • Barreca, Davide|||0000-0002-8779-3386
  • Gasparotto, Alberto|||0000-0003-4626-651X
  • Sada, Cinzia|||0000-0002-7607-0481
  • Martí-Sánchez, Sara|||0000-0003-4283-1489
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Maccato, Chiara|||0000-0001-6368-5754
A facile two-step vapor phase synthetic approach is proposed for the fabrication of MnO thin films chemically modified with fluorine, and eventually functionalized with silver or titania. The adopted strategy exploits the initial chemical vapor deposition (CVD) of MnO on Si(100) substrates starting from a diamine diketonate Mn(ii) complex, followed by the controlled radio frequency (RF)-sputtering of silver or titania. Complementary analytical techniques were employed to investigate the crystallinity (X-ray diffraction), chemical composition (X-ray photoelectron spectroscopy, secondary ion mass spectrometry, energy dispersive X-ray spectroscopy), morphology and nano-organization (field emission-scanning electron microscopy, atomic force microscopy, transmission electron microscopy) of both pristine and functionalized manganese oxide thin films. Under the adopted operating conditions, the target Mn(ii) complex acted as a single-source precursor for both Mn and F, leading to the formation of phase-pure hausmannite MnO films characterized by a uniform in-depth fluorine content. In addition, the obtained results gave evidence of the formation of high purity Ag/F:MnO and TiO/F:MnO composites with a close contact between the single constituents. This work outlines an amenable and efficient method for the vapor phase growth of composite MnO-based thin films, which are favorable candidates for diverse technological applications, from photocatalysis to gas sensing.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

SnP nanocrystals as anode materials for Na-ion batteries

  • Liu, Junfeng|||0000-0003-3164-6472
  • Wang, Shutao|||0000-0002-1689-2272
  • Kravchyk, Kostiantyn
  • Ibáñez, Maria|||0000-0001-5013-2843
  • Krumeich, Frank|||0000-0001-5625-1536
  • Widmer, Roland
  • Nasiou, Déspina
  • Meyns, Michaela|||0000-0003-2476-9001
  • Llorca, Jordi|||0000-0002-7447-9582
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Kovalenko, Maksym V.|||0000-0002-6396-8938
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Tin monophosphide is a layered material consisting of Sn-P-P-Sn sandwiches that are stacked on top of each other to form a three dimensional crystallographic structure. Its composition and crystal structure makes it an excellent candidate anode material for sodium-ion batteries (SIBs). However, SnP is yet to be explored for such and other applications due to its challenging synthesis. In the present work, we report the synthesis of SnP nanocrystals (NCs) from the reaction of hexamethylphosphorous triamide (HMPT) and a tin phosphonate prepared from tin oxalate and a long chain phosphonic acid. SnP NCs obtained from this reaction displayed a spherical geometry and a trigonal crystallographic phase with a superstructure attributed to ordered diphosphorus pairs. Such NCs were mixed with carbon black and used as anode materials in SIBs. SIBs based on SnP NCs and sodium(i) bis(fluorosulfonyl)imide (NaFSI) electrolyte displayed a high reversible capacity of 600 mA h g at a current density of 100 mA g and cycling stability for over 200 cycles. Their excellent cycling performance is associated with both the small size of the crystal domains and the particular composition and phase of SnP which prevent mechanical disintegration and major phase separation during sodiation and desodiation cycles. These results demonstrate SnP to be an attractive anode material for sodium ion batteries.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Reduction of Thermal Conductivity in Nanowires by Combined Engineering of Crystal Phase and Isotope Disorder

  • Mukherjee, Samik|||0000-0002-5279-1110
  • Givan, Uri
  • Senz, Stephan
  • De La Mata, Maria|||0000-0002-1581-4838
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Moutanabbir, Oussama|||0000-0002-0721-3696
Nanowires are a versatile platform to investigate and harness phonon and thermal transport phenomena in nanoscale systems. With this perspective, we demonstrate herein the use of crystal phase and mass disorder as effective degrees of freedom to manipulate the behavior of phonons and control the flow of local heat in silicon nanowires. The investigated nanowires consist of isotopically pure and isotopically mixed nanowires bearing either a pure diamond cubic or a cubic-rhombohedral polytypic crystal phase. The nanowires with tailor-made isotopic compositions were grown using isotopically enriched silane precursors SiH, SiH, and SiH with purities better than 99.9%. The analysis of polytypic nanowires revealed ordered and modulated inclusions of lamellar rhombohedral silicon phases toward the center in otherwise diamond-cubic lattice with negligible interphase biaxial strain. Raman nanothermometry was employed to investigate the rate at which the local temperature of single suspended nanowires evolves in response to locally generated heat. Our analysis shows that the lattice thermal conductivity in nanowires can be tuned over a broad range by combining the effects of isotope disorder and the nature and degree of polytypism on phonon scattering. We found that the thermal conductivity can be reduced by up to ∼40% relative to that of isotopically pure nanowires, with the lowest value being recorded for the rhombohedral phase in isotopically mixed Si Si nanowires with composition close to the highest mass disorder (x ∼ 0.5). These results shed new light on the fundamentals of nanoscale thermal transport and lay the groundwork to design innovative phononic devices.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

Optimizing the yield of A-polar GaAs nanowires to achieve defect-free zinc blende structure and enhanced optical functionality

  • Zamani, Mahdi|||0000-0003-0750-2938
  • Tütüncüoglu, Gözde
  • Martí-Sánchez, Sara|||0000-0003-4283-1489
  • Francaviglia, Luca|||0000-0002-2138-0837
  • Güniat, Lucas|||0000-0001-7883-4433
  • Ghisalberti, Lea
  • Potts, Heidi A.
  • Friedl, Martin
  • Markov, Edoardo
  • Kim, Wonjong
  • Leran, Jean-Baptiste
  • Dubrovskii, Vladimir G.|||0000-0003-2088-7158
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Fontcuberta i Morral, Anna|||0000-0002-5070-2196
Compound semiconductors exhibit an intrinsic polarity, as a consequence of the ionicity of their bonds. Nanowires grow mostly along the (111) direction for energetic reasons. Arsenide and phosphide nanowires grow along (111)B, implying a group V termination of the (111) bilayers. Polarity engineering provides an additional pathway to modulate the structural and optical properties of semiconductor nanowires. In this work, we demonstrate for the first time the growth of Ga-assisted GaAs nanowires with (111)A-polarity, with a yield of up to ∼50%. This goal is achieved by employing highly Ga-rich conditions which enable proper engineering of the energies of A and B-polar surfaces. We also show that A-polarity growth suppresses the stacking disorder along the growth axis. This results in improved optical properties, including the formation of AlGaAs quantum dots with two orders or magnitude higher brightness. Overall, this work provides new grounds for the engineering of nanowire growth directions, crystal quality and optical functionality.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

III-V Integration on Si(100), Vertical Nanospades

  • Güniat, Lucas|||0000-0001-7883-4433
  • Martí-Sánchez, Sara|||0000-0003-4283-1489
  • Garcia, Oscar|||0000-0001-8541-7013
  • Boscardin, Mégane
  • Vindice, David
  • Tappy, Nicolas
  • Friedl, Martin
  • Kim, Wonjong
  • Zamani, Mahdi|||0000-0003-0750-2938
  • Francaviglia, Luca|||0000-0002-2138-0837
  • Balgarkashi, Akshay
  • Leran, Jean-Baptiste
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Fontcuberta i Morral, Anna|||0000-0002-5070-2196
III-V integration on Si(100) is a challenge: controlled vertical vapor liquid solid nanowire growth on this platform has not been reported so far. Here we demonstrate an atypical GaAs vertical nanostructure on Si(100), coined nanospade, obtained by a nonconventional droplet catalyst pinning. The Ga droplet is positioned at the tip of an ultrathin Si pillar with a radial oxide envelope. The pinning at the Si/oxide interface allows the engineering of the contact angle beyond the Young-Dupré equation and the growth of vertical nanospades. Nanospades exhibit a virtually defect-free bicrystalline nature. Our growth model explains how a pentagonal twinning event at the initial stages of growth provokes the formation of the nanospade. The optical properties of the nanospades are consistent with the high crystal purity, making these structures viable for use in integration of optoelectronics on the Si(100) platform.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

SnS2/g-C3N4/graphite nanocomposites as durable lithium-ion battery anode with high pseudocapacitance contribution

  • Zuo, Yong|||0000-0003-1564-467X
  • Xu, Xijun
  • Zhang, Chaoqi|||0000-0002-0357-235X
  • Li, Junshan|||0000-0002-1482-1972
  • Du, Ruifeng
  • Wang, Xiang
  • Han, Xu|||0000-0001-8319-8830
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Llorca, Jordi|||0000-0002-7447-9582
  • Liu, Jun|||0000-0001-5288-3042
  • Cabot i Codina, Andreu|||0000-0002-7533-3251
Tin disulfide is a promising anode material for Li-ion batteries (LIB) owing to its high theoretical capacity and the abundance of its composing elements. However, bare SnS suffers from low electrical conductivity and large volume expansion, which results in poor rate performance and cycling stability. Herein, we present a solution-based strategy to grow SnS nanostructures within a matrix of porous g-CN (CN) and high electrical conductivity graphite plates (GPs). We test the resulting nanocomposite as anode in LIBs. First, SnS nanostructures with different geometries are tested, to find out that thin SnS nanoplates (SnS-NPLs) provide the highest performances. Such SnS-NPLs, incorporated into hierarchical SnS/CN/GP nanocomposites, display excellent rate capabilities (536.5 mA h g at 2.0 A g) and an outstanding stability (∼99.7% retention after 400 cycles), which are partially associated with a high pseudocapacitance contribution (88.8% at 1.0 mV s). The excellent electrochemical properties of these nanocomposites are ascribed to the synergy created between the three nanocomposite components: i) thin SnS-NPLs provide a large surface for rapid Li-ion intercalation and a proper geometry to stand volume expansions during lithiation/delithiation cycles; ii) porous CN prevents SnS-NPLs aggregation, habilitates efficient channels for Li-ion diffusion and buffer stresses associated to SnS volume changes; and iii) conductive GPs allow an efficient charge transport.
Dipòsit Digital de Documents de la UAB
Publication Artículo científico (JournalArticle)

High magnetic coercivity in nanostructured Mn3O4 thin films obtained by chemical vapor deposition, High low-temperature coercivity in Mn3O4 thin films obtained by chemical vapor deposition

  • Bigiani, Lorenzo|||0000-0001-7404-2340
  • Hassan, Mariam|||0000-0002-8592-5672
  • Peddis, Davide|||0000-0003-0810-8860
  • Maccato, Chiara|||0000-0001-6368-5754
  • Varvaro, Gaspare|||0000-0001-7313-7268
  • Sada, Cinzia|||0000-0002-7607-0481
  • Bontempi, Elza|||0000-0003-1656-7506
  • Martí-Sánchez, Sara|||0000-0003-4283-1489
  • Arbiol i Cobos, Jordi|||0000-0002-0695-1726
  • Barreca, Davide|||0000-0002-8779-3386
Nanostructured α-MnO (haussmannite) thin films consisting of evenly interconnected nanoaggregates were prepared on Si(100) substrates by chemical vapor deposition from a Mn(II) diketonate-diamine precursor under different reaction atmospheres (dry vs wet O) and total operating pressures. The combination of chemico-physical results obtained by the joint use of complementary techniques enabled us to demonstrate the obtainment of high-purity MnO materials free from other manganese oxide phases, characterized by controllable structural and morphological characteristics as a function of the adopted processing conditions. Magnetic properties were investigated by analyzing temperature dependence (i.e., field-cooled and zero-field-cooled measurements) and field-dependence of the magnetization behavior. The obtained films show bulk-like magnetic properties, together with extraordinarily high low-temperature in-plane coercivities (up to ∼1 T). The possibility to tailor these values by varying the content of microstructural defects may foster the implementation of the obtained films in eventual technological applications.