Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of ferrite nanoparticle type and content on the crystallization kinetics and electroactive phase nucleation of poly(vinilidene fluoride)

  • Sencadas, Vitor Joao Gomes Da Silva
  • Pitaes, Alexandre
  • Benelmekki, Maria
  • Lanceros Mendez, Senen
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
[EN] This work reports on the nucleation of the beta-phase of poly(vinylidene fluoride) (PVDF) by incorporating CoFe2O4 and NiFe2O4 nanoparticles, leading in this way to the preparation of magnetoelectric composites. The fraction of filler nanoparticles needed to produce the same beta- to alpha-phase ratio in crystallized PVDF is 1 order of magnitude lower in the cobalt ferrite nanoparticles. The interaction between nanoparticles and PVDF chains induce the all-trans conformation in PVDF segments, and this structure then propagates in crystal growth. The nucleation kinetics is enhanced by the presence of nanoparticles, as corroborated by the increasing number of spherulites with increasing nanoparticle content and by the variations of the Avrami's exponent. Further, the decrease of the crystalline fraction of PVDF with increasing nanoparticle content indicates that an important fraction of polymer chains are confined in interphases with the filler particle., This work is funded by FEDER funds through the “Programa Operacional Factores de Competitividade COMPETE” and by national funds by FCT- Fundac-~ao para a Ci^encia e a Tecnologia, project references NANO/NMed-SD/0156/2007 and PTDC/CTM/69316/2006. V.S. thanks the FCT for the SFRH/BPD/63148/2009 grant. P.M. thanks the FCT for the SFRH/BD/45265/2008 grant. J.L.G.-R. acknowledges the support of the Spanish Ministry of Education through Project No. MAT2010-21611-C03-01 (including the FEDER financial support), Project EUI2008-00126, and funding in the Centro de Investigacion Principe Felipe in the field of Regenerative Medicine through the collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana), and the Instituto de Salud Carlos III (Ministry of Science and Innovation).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Determination of the parameters affecting electrospun chitosan fiber size distribution and morphology

  • Sencadas, Vitor Joao Gomes Da Silva
  • Correia, Daniela Maria
  • Areias Cepa, Anabela
  • Botelho, G.
  • Fonseca, A.M.
  • Neves, I.C.
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
  • Lanceros Mendez, Senen
The production of chitosan nanofiber mats by electrospinning presents serious difficulties due to the lack of suitable solvents and the strong influence of processing parameters on the fiber properties. Two are the main problems to be solved: to control the properties of the solution in order to obtain large area uniform fiber mats by having a stable flow rate and to avoid sparks during the process, damaging the fiber mats. In this work chitosan electrospun mats have been prepared form solutions of trifluoroacetic acid/dichloromethanemixtures, allowing solving the aforementionedproblems.Mats withuniformfibers of submicron diameters without beads were obtained. Further, the influence of the different solution and process parameters on the mean fiber diameter and on the width of the distribution of the fiber sizes has been assessed. Solvent composition, needle diameter, applied voltage and traveling distance were the parameters considered in this study., This work is funded by FEDER funds through the “Programa Operacional Factores de Competitividade – COMPETE” and by national funds by FCT – Fundac ̧ ão para a Ciência e a Tecnologia, project references NANO/NMed-SD/0156/2007. VS thanks the FCT for the SFRH/BPD/63148/2009 grants. JLGR acknowledge the sup- port of the Spanish Ministry of Science and Innovation through project No. MAT2010-21611-C03-01 (including the FEDER finan- cial support) and Programa Nacional de Internacionalización de la I+D project EUI2008-00126. Funding for research in the field of Regenerative Medicine through the collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana), and the Insti- tuto de Salud Carlos III (Ministry of Science and Innovation) is also acknowledged. Thanks are due to the National NMR Network that was purchased within the framework of the National Program for Scientific Re-equipment, contract REDE/1517/RMN/2005 with funds from POCI 2010 (FEDER) and FCT. Also thank to the UPV Microscopy Service for the use of their lab.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fibronectin adsorption and cell response on electroactive poly (vinylidene fluoride) films

  • Ribeiro, Clarisse
  • Panadero Pérez, Juan Alberto
  • Sencadas, Vitor Joao Gomes Da Silva
  • Lanceros Mendez, Senen
  • Tamaño Machiavello, María Noel
  • Salmerón Sánchez, Manuel
  • Moratal, David|||0000-0002-2825-3646
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Due to the large potential of electroactive materials in novel tissue engineering strategies, the aim of this work is to determine if the crystalline phase and/or the surface electrical charge of electroactive poly(vinylidene fluoride), PVDF, have influence on the biological response in monolayer cell culture. Non-polar α-PVDF and electroactive β-PVDF were prepared. The β-PVDF films were poled by corona discharge to show negative or positive electrical surface charge density. It has been concluded that hydrophilicity of the PVDF substrates depends significantly on crystalline phase and polarity. Furthermore, by means of atomic force microscopy and an enzyme-linked immunosorbent assay test, it has been shown that positive or negative poling strongly influences the behavior of β-PVDF supports with respect to fibronectin (FN) adsorption, varying the exhibition of adhesion ligands of adsorbed FN. Culture of MC3T3-E1 pre-osteoeblasts proved that cell proliferation depends on surface polarity as well. These results open the viability of cell culture stimulation by mechanical deformation of a piezoelectric substrate that results in varying electrical charge densities on the substrate surface., This work is funded by FEDER funds through the 'Programa Operacional Factores de Competitividade-COMPETE' and by national funds by FCT-Fundacao para a Ciencia e a Tecnologia, project reference NANO/NMed-SD/0156/2007. CR thanks the INL for a PhD grant. VS and JAP thank the FCT for the SFRH/BPD/63148/2009 and SFRH/BD/64586/2009/grants, respectively. JLGR acknowledges the support of the Spanish Ministry of Education through project no MAT2010-21611-C03-01 (including the FEDER financial support), project EUI2008-00126 and funding in the Centro de Investigacion Principe Felipe in the field of Regenerative Medicine through the collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana) and the Instituto de Salud Carlos III (Ministry of Science and Innovation). The authors thank Armando Ferreira for the help with the contact angle measurements and CENTI, Portugal, for allowing the use of the set-up.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Physical-chemical properties of cross-linked chitosan electrospun fiber mats

  • Sencadas, Vitor Joao Gomes Da Silva
  • Correia, Daniela
  • Ribeiro, Clarisse
  • Moreira, S.
  • Botelho, G.
  • Lanceros Mendez, Senen
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Chitosan fiber mats were successfully processed by electrospinning. The as-spun fiber mats were neutralized with ethanol and cross-linked with glutaraldehyde. A decrease of the fiber average diameter from 243 +/- 43 nm down to 215.53 nm was observed for the neutralized and cross-linking chitosan membrane. It was found that the processing conditions do not alter the initial deacetylation degree of the polymer. Polymer crystallinity index showed a decrease from 61% for the Protasan material down to 17% for the cross-linking fiber mats. A swelling index up to 1000% was observed for the cross-linked samples. Preliminary MC-3T3-E1 cell culture results showed good cell adhesion and proliferation in the cross-linked chitosan fiber mats., This work is funded by FEDER funds through the "Programa Operacional Factores de Competitividade - COMPETE" and by national funds by FCT - Fundacao para a Ciencia e a Tecnologia, project references NANO/NMed-SD/0156/2007. V.S. and SM thanks the FCT grants SFRH/BPD/63148/2009 and SFRH/BPD/64726/2009, respectively. The authors also thank the support of the COST Action MP1003, 2010 'European Scientific Network for Artificial Muscles' (ESNAM). JLGR acknowledge the support of the Spanish Ministry of Science and Innovation through project No. MAT2010-21611-C03-01 (including the FEDER financial support) and Programa Nacional de Internacionalizacion de la I+D project EUI2008-00126. The authors also thank the National NMR Network (National Program for Scientific Re-equipment, REDE/1517/RMN/2005, funds from POCI 2010 (FEDER) and FCT) and Microscopy Service of the UPV for the use of their lab.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessment of Parameters Influencing fiber characteristics of chitosan nanofiber membrane to optimize fiber mat productioi

  • Areias, A.C.
  • Gómez-Tejedor, José Antonio
  • Sencadas, V.
  • Alio, J.
  • Lanceros-Mendez, S.
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Electrospun chitosan nanofiber mats have been obtained using chitosan solutions in a mixture of trifluoroacetic acid and dichloromethane. The relationship between processing parameters (solvent composition, polymer concentration in the solution, feeding rate, applied voltage, traveling distance between the needle, and the collector) and fiber morphology was studied. Taguchi's methodology was followed to determine which parameters have the strongest influence on mean fiber diameter and fiber homogeneity. Chitosan nanofibers obtained with this procedure were water soluble due to the protonation of amine side groups but were successfully neutralized by immersion in calcium carbonate solutions. It was established that fiber diameter is mainly determined by the solution concentration and the distance from the needle to the collector while other parameters have less influence. The set of parameters that produce the thinnest fibers were a concentration of 8 wt%, a TFA/DCM ratio of 80:20 (v/v%), a voltage of 30 kV, a flow rate of 6.0 mL/h, a gap distance of 10 cm, using a needle diameter of 0.5, allowing to produce randomly oriented mats with a mean fiber thickness of 66 nm. © 2012 Society of Plastics Engineers., Contract grant sponsor: Portuguese Foundation for Science and Technology (FCT); contract grant number: NANO/NMed-SD/0156/2007; Contract grant sponsor: FCT; contract grant number: SFRH/BPD/63148/2009; Contract grant sponsor: Spanish Ministry of Science and Innovation; contract grant number: MAT2010-21611-C03-01; Contract grant sponsor: Programa Nacional de Internacionalizacion de la I+D; contract grant number: EUI2008-00126; Contract grant sponsors: Regenerative Medicine collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana), and the Instituto de Salud Carlos III (Ministry of Science and Innovation); Contract grant sponsors: Spanish Ministry of Science and Innovation, Centro para el Desarrollo Tecnologico Industrial (CDTI), CENIT: "Customized Eye Care'' and CeyeC; contract grant number: CEN-20091021; Contract grant sponsor: The translation of this paper was funded by the Universitat Politecnica de Valencia, Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Relaxation dynamics of poly(vinylidene fluoride) studied by dynamical mechanical measurements and dielectric spectroscopy

  • Sencadas, V.
  • Lanceros-Mendez, S.
  • Andrio Balado, A.
  • Sabater i Serra, Roser|||0000-0002-5550-7066
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
[EN] The aim of this study is to analyze the mobility of polymer chains in semicrystalline poly(vinylidene fluoride) (PVDF). PVDF crystallizes from the melt in the crystalline phase. The transformation from the phase to the electroactive phase can be induced by stretching at temperatures in the range between 80 and 140 ◦C. The spherulitic structure of the crystalline phase is deformed during stretching to form fibrils oriented in the direction of the strain. The amorphous phase confined among the crystalline lamellae is distorted as well and some degree of orientation of the polymer chains is expected. Dynamicmechanical and dielectric spectroscopy measurements were performed in PVDF films stretched to strain ratios up to 5 at temperatures between 80 and 140 ◦C. Dynamic-mechanical measurements were conducted between −60 ◦C and melting and in this temperature range the relaxation spectra show the main relaxation of the amorphous phase (called -relaxation) and at higher temperatures a relaxation related to crystallites motions (c-relaxation). Although the mean relaxation times of the -relaxation are nearly equal in PVDF before and after crystal phase transformation, a significant change of shape of the relaxation spectrum proves the effect of chain distortion due to crystal reorganization. In stretched PVDF the elastic modulus of the polymer in the direction of deformation is significantly higher than in the transversal one, as expected by chain and crystals fibril orientation. The recovery of the deformation when the sample is heated is related with the appearance of the c-relaxation. Dielectric spectroscopy spectrum shows the main relaxation of the amorphous phase and a secondary process (-relaxation) at lower temperatures. Stretching produces significant changes in the relaxation processes, mainly in the strength and shape of the main relaxation. The Havriliak-Negami function has been applied to analyze the dielectric response., This work is funded by FEDER funds through the "Programa Operacional Factores de Competitividade-COMPETE" and by national funds by FCT-Fundacao para a Ciencia e Tecnologia, project references NANO/NMed-SD/0156/2007, PTDC/CTM/69316/2006 and PTDC/CTM-NAN/112574/2009. V. S. thanks the FCT for the SFRH/BPD/63148/2009 grant. JLGR acknowledges the support of the Spanish Ministry of Science and Innovation through MAT2010-21611-C03-01 (including the FEDER financial support), and EUI2008-00126 projects and funding in the Centro de Investigacion Principe Felipe in the field of Regenerative Medicine through the collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana), and the Instituto de Salud Carlos III (Ministry of Science and Innovation). The authors also acknowledge support from the COST Action MP1003, 2010 "European Scientific Network for Artificial Muscles".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Glass transition and polymer dynamics in silver/poly(methyl methacrylate) nanocomposites

  • Pandis, C.
  • Logakis, E.
  • Kyritsis, A.
  • Pissis, P.
  • Vodnik, V. V.
  • Dzunuzovic, E.
  • Nedeljkovic, J. M.
  • Djokovic, V.
  • Rodriguez-Hernandez, Jose-Carlos|||0000-0002-1735-824X
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Dynamic mechanical-thermal analysis (DMTA), differential scanning calorimetry (DSC), thermally stimulated depolarization currents (TSDC) and, mainly, broadband dielectric relaxation spectroscopy (DRS) were employed to investigate in detail glass transition and polymer dynamics in silver/poly(methyl methacrylate) (Ag/PMMA) nanocomposites. The nanocomposites were prepared by radical polymerization of MMA in the presence of surface modified Ag nanoparticles with a mean diameter of 5.6 nm dispersed in chloroform. The fraction of Ag nanoparticles in the final materials was varied between 0 and 0.5 wt%, the latter corresponding to 0.055 vol%. The results show that the nanoparticles have practically no effect on the time scale of the secondary ß and ¿ relaxations, whereas the magnitude of both increases slightly but systematically with increasing filler content. The segmental ¿ relaxation, associated with the glass transition, becomes systematically faster and stronger in the nanocomposites. The glass transition temperature T g decreases with increasing filler content of the nanocomposites up to about 10 °C, in good correlation by the four techniques employed. Finally, the elastic modulus decreases slightly but systematically in the nanocomposites, both in the glassy and in the rubbery state. The results are explained in terms of plasticization of the PMMA matrix, due to constraints imposed to packing of the chains by the Ag nanoparticles, and at the same time, of the absence of strong polymer-filler interactions, due to the surface modification of the Ag nanoparticles by oleylamine at the stage of preparation. © 2011 Elsevier Ltd. All rights reserved., JLGR acknowledges the support of the Spanish Ministry of Science and Innovation through project No. EUI2008-00126 and funding in the Centro de Investigacion Principe Felipe in the field of Regenerative Medicine through the collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana), and the Instituto de Salud Carlos III (Ministry of Science and Innovation).