Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 20
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Dielectric relaxation, ac conductivity and electric modulus in poly(vinylidene fluoride)/NaY zeolite composites

  • Lopes, A.C.
  • Costa, C.M.
  • Neves, I.C.
  • Lanceros-Mendez, S.
  • Sabater i Serra, Roser|||0000-0002-5550-7066
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
[EN] Poly(vinylidene fluoride)/zeolite composites prepared by solvent casting at 190 °C have been investigated by scanning electronic microscopy, Fourier transformed infrared spectroscopy and broadband dielectric relaxation spectroscopy. The inclusion of the NaY zeolite filler in the polymer matrix induces the crystallization of poly(vinylidene fluoride), PVDF, in the electroactive γ phase. The dielectric function, ac conductivity and electric modulus of the composites were investigated as a function of zeolite content in the frequency range from 0.1 Hz to 1×107 Hz at temperatures from −120 to 150 °C. The main relaxation process (β-relaxation) of the amorphous phase of the polymer matrix is not affected by the presence of the zeolite, as verified by the similar relaxation parameters obtained for the pure polymer and for the PVDF/NaY4% composite. In a similar way, the zeolite low temperature relaxation is not significantly affected by the polymer phase. On the other hand, the electric modulus formalismreveals significant contributions of the fillers to the electrical permittivity and conductivity of the composites. The presence of the zeolite particles increases ac conductivity and theMaxwell Wagner Sillars contribution that is predominant at low frequencies with respect to ohmic contribution to permittivity., This work is partially funded by the Centre of Physics and Centre of Chemistry (University of Minho, Portugal) and by FEDER funds through the Programa Operacional Factores de Competitividade-COMPETE and by national funds by FCT-Fundação para a Ciência e a Tecnologia, project references, NANO/NMed-SD/0156/2007, PTDC/CTM/69316/2006, PEst-C/QUI/UI0686/2011 and PTDC/CTM-NAN/112574/2009. A.C.L. and C.M.C. also thank the FCT for the grant SFRH/BD/62507/2009 and SFRH/BD/68499/2010, respectively. The authors also thank support from the COST Action MP1003, the European Scientific Network for Artificial Muscles (ESNAM)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Strategies for the development of three dimensional scaffolds from piezoelectric poly(vinylidene fluoride)

  • Correia , Daniela
  • Ribeiro, Clarisse
  • Sencadas, V.
  • Vikingsson, Line
  • Gasch, M. Oliver
  • Botelho, G.
  • Lanceros-Mendez, Senentxu
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Cell supports based on electroactive materials, that generate electrical signal variations as a response to mechanical deformations and vice-versa, are gaining increasing attention for tissue engineering applications. In particular, poly(vinylidene fluoride), PVDF, has been proven to be suitable for these applications in the form of films and two-dimensional membranes. In this work, several strategies have been implemented in order to develop PVDF three-dimensional scaffolds. Three processing methods, including solvent casting with particulate leaching and three-dimensional nylon, and freeze extraction with poly(vinyl alcohol) templates are presented in order to obtain three-dimensional scaffolds with different architectures and interconnected porosity. Further, it is shown that the scaffolds are in the electroactive beta-phase and show a crystallinity degree of similar to 45%. Finally, quasi-static mechanical measurements showed that an increase of the porous size within the scaffold leads to a tensile strengths and the Young's modulus decrease, allowing tuning scaffold properties for specific tissues., This work is funded by FEDER funds through the "Programa Operacional Fatores de Competitividade - COMPETE" and by national funds arranged by FCT Fundacao para a Ciencia e a Tecnologia, project reference PEST-C/FIS/U1607/2014. The authors also thank support from the COST Action MP1301 "New Generation Biomimetic and Customized Implants for Bone Engineering". DMC and CR, thank the FCT for the SFRH/BD/82411/2011 and SFRH/BPD/90870/2012 grants, respectively. JLGR acknowledges the support of Ministerio de Economia y Competitividad, MINECO, through the MAT2013-46467-C4-1-R project CIBER-BBN is an initiative funded by the VI National R&D&i Plan 2008-2011, Iniciativa Ingenio 2010, Consolider Program, CIBER Actions and financed by the Instituto de Salud Carlos III with assistance from the European Regional Development Fund.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Thermal Properties of Electrospun Poly(Lactic Acid) Membranes

  • Sencadas, Vitor Joao Gomes Da Silva
  • Costa, C.M.
  • Botelho, G.
  • Caparrós, C.
  • Ribeiro, C.
  • Lanceros-Mendez, Senentxu
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
[EN] Poly(lactic acid) (PLA) electrospun membranes were obtained by electrospinning and characterized by scanning electron microscopy (SEM) and thermal analysis. The polymer membranes showed a random fiber distribution with a mean diameter of 1µm (±300 nm). Differential scanning calorimetry (DSC) experiments showed that the membranes had a glass transition, cold crystallization, and melting temperatures of 54, 90, and 151◦C, respectively. The kinetic study of thermal degradation of PLA under a nitrogen atmosphere was performed by means of thermogravimetry (TGA). It was found that the thermal decomposition kinetics of PLA could be interpreted in terms of a multi-step degradation mechanism. Several theoretical models were applied to the TGA data. The activation energies obtained by the Broido and Ozawa–Flynn–Wall (OFW) models were in good agreement with the value of the activation energy calculated by the Kissinger method, The authors thank the Portuguese Foundation for Science and Technology (FCT) for finantial support under grants NANO/NMed-SD/0156/2007 and PTDC/CTM/73030/2006. V. Sencadas thanks the FCT for the SFRH/BPD/63148/2009 grant. C. Ribeiro thanks the INL for a PhD grant. J. L. Gomez-Ribelles acknowledges the support of the Spanish Ministry of Education through project No. MAT2007-66759-C03-01 (including the FEDER financial support, and funding in the Centro de Investigacion Principe Felipe in the field of Regenerative Medicine through the collaboration agreement between the Conselleria de Sanidad (Generalitat Valenciana), and the Instituto de Salud Carlos III (Ministry of Science and Innovation).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of oxygen plasma treatment parameters on poly(vinylidene fluoride) electrospun fiber mats wettability

  • Correia, Daniela M.
  • Ribeiro, Clarisse
  • Sencadas, Vitor Joao Gomes Da Silva
  • Botelho, G.
  • Carabineiro, S.A.C.
  • Lanceros-Mendez, Senentxu
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
[EN] Electrospun poly(vinylidene fluoride) (PVDF) fiber mats find applications in an increasing number of areas, such as battery separators, filtration and detection membranes, due to their excellent properties. However, there are limitations due to the hydrophobic nature and low surface energy of PVDF. In this work, oxygen plasma treatment has been applied in order to modify the surface wettability of PVDF fiber mats and superhydrophilic PVDF electrospun membranes have been obtained. Further, plasma treatment does not significantly influences fiber average size (similar to 400 +/- 200 nm), morphology, electroacfive beta-phase content (similar to 80-85%) or the degree of crystallinity (X-c of 42 +/- 2%), allowing to maintain the excellent physical-chemical characteristics of PVDF. Plasma treatment mainly induces surface chemistry modifications, such as the introduction of oxygen and release of fluorine atoms that significantly changes polymer membrane wettability by a reduction of the contact angle of the polymer fibers and an overall decrease of the surface tension of the membranes., This work is funded by FEDER funds through the "Programa Operacional Fatores de Competitividade - COMPETE" and by national funds arranged by FCT - Fundacao para a Ciencia e a Tecnologia, project references NANO/NMed-SD/0156/2007, PTDC/CTM-NAN/112574/2009, PEST-C/FIS/UI607/2011 and PEST-C/QUI/UIO686/2013. The authors also thank funding from Matepro - Optimizing Materials and Processes", ref. NORTE-07-0124-FEDER-000037", co-funded by the "Programa Operacional Regional do Norte" (ON.2-O Novo Norte), under the "Quadro de Referencia Estrategico Nacional" (QREN), through the "Fundo Europeu de Desenvolvimento Regional" (FEDER). The authors also thank support from the COST Action MP1003, 2010 'European Scientific Network for Artificial Muscles', MP1206 "Electrospun Nano-fibres for bio inspired composite materials and innovative industrial applications" and MP1301 "New Generation Biomimetic and Customized Implants for Bone Engineering". DMC, CR, VS and SACC thank the FCT for the SFRH/BD/82411/2011, SFRH/BPD/90870/2012, SFRH/BPD/64958/2009 and Investigator FCT IF/1381/2013 grants, respectively. JLGR acknowledges the support of Ministerio de Economia y Competitividad, MINECO, through the MAT2013-46467-C4-1-R project. CIBER-BBN is an initiative funded by the VI National R&D&i Plan 2008-2011, Iniciativa Ingenio 2010, Consolider Program, CIBER Actions and financed by the Instituto de Salud Carlos III with assistance from the European Regional Development Fund. Dr. Carlos M. Sa (CEMUP) is acknowledged for assistance with XPS analyses.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Determination of the parameters affecting electrospun chitosan fiber size distribution and morphology

  • Sencadas, Vitor Joao Gomes Da Silva
  • Correia, Daniela Maria
  • Areias Cepa, Anabela
  • Botelho, G.
  • Fonseca, A.M.
  • Neves, I.C.
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
  • Lanceros Mendez, Senen
The production of chitosan nanofiber mats by electrospinning presents serious difficulties due to the lack of suitable solvents and the strong influence of processing parameters on the fiber properties. Two are the main problems to be solved: to control the properties of the solution in order to obtain large area uniform fiber mats by having a stable flow rate and to avoid sparks during the process, damaging the fiber mats. In this work chitosan electrospun mats have been prepared form solutions of trifluoroacetic acid/dichloromethanemixtures, allowing solving the aforementionedproblems.Mats withuniformfibers of submicron diameters without beads were obtained. Further, the influence of the different solution and process parameters on the mean fiber diameter and on the width of the distribution of the fiber sizes has been assessed. Solvent composition, needle diameter, applied voltage and traveling distance were the parameters considered in this study., This work is funded by FEDER funds through the “Programa Operacional Factores de Competitividade – COMPETE” and by national funds by FCT – Fundac ̧ ão para a Ciência e a Tecnologia, project references NANO/NMed-SD/0156/2007. VS thanks the FCT for the SFRH/BPD/63148/2009 grants. JLGR acknowledge the sup- port of the Spanish Ministry of Science and Innovation through project No. MAT2010-21611-C03-01 (including the FEDER finan- cial support) and Programa Nacional de Internacionalización de la I+D project EUI2008-00126. Funding for research in the field of Regenerative Medicine through the collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana), and the Insti- tuto de Salud Carlos III (Ministry of Science and Innovation) is also acknowledged. Thanks are due to the National NMR Network that was purchased within the framework of the National Program for Scientific Re-equipment, contract REDE/1517/RMN/2005 with funds from POCI 2010 (FEDER) and FCT. Also thank to the UPV Microscopy Service for the use of their lab.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fibronectin adsorption and cell response on electroactive poly (vinylidene fluoride) films

  • Ribeiro, Clarisse
  • Panadero Pérez, Juan Alberto
  • Sencadas, Vitor Joao Gomes Da Silva
  • Lanceros Mendez, Senen
  • Tamaño Machiavello, María Noel
  • Salmerón Sánchez, Manuel
  • Moratal, David|||0000-0002-2825-3646
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Due to the large potential of electroactive materials in novel tissue engineering strategies, the aim of this work is to determine if the crystalline phase and/or the surface electrical charge of electroactive poly(vinylidene fluoride), PVDF, have influence on the biological response in monolayer cell culture. Non-polar α-PVDF and electroactive β-PVDF were prepared. The β-PVDF films were poled by corona discharge to show negative or positive electrical surface charge density. It has been concluded that hydrophilicity of the PVDF substrates depends significantly on crystalline phase and polarity. Furthermore, by means of atomic force microscopy and an enzyme-linked immunosorbent assay test, it has been shown that positive or negative poling strongly influences the behavior of β-PVDF supports with respect to fibronectin (FN) adsorption, varying the exhibition of adhesion ligands of adsorbed FN. Culture of MC3T3-E1 pre-osteoeblasts proved that cell proliferation depends on surface polarity as well. These results open the viability of cell culture stimulation by mechanical deformation of a piezoelectric substrate that results in varying electrical charge densities on the substrate surface., This work is funded by FEDER funds through the 'Programa Operacional Factores de Competitividade-COMPETE' and by national funds by FCT-Fundacao para a Ciencia e a Tecnologia, project reference NANO/NMed-SD/0156/2007. CR thanks the INL for a PhD grant. VS and JAP thank the FCT for the SFRH/BPD/63148/2009 and SFRH/BD/64586/2009/grants, respectively. JLGR acknowledges the support of the Spanish Ministry of Education through project no MAT2010-21611-C03-01 (including the FEDER financial support), project EUI2008-00126 and funding in the Centro de Investigacion Principe Felipe in the field of Regenerative Medicine through the collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana) and the Instituto de Salud Carlos III (Ministry of Science and Innovation). The authors thank Armando Ferreira for the help with the contact angle measurements and CENTI, Portugal, for allowing the use of the set-up.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Novel poly(vinylidene fluoride-trifluoroethylene)/poly(ethylene oxide) blends for battery separators in lithium-ion applications

  • Costa, Carlos M.
  • Nunes-Pereira, J.
  • Rodrigues, L.C.
  • Silva, M.M.
  • Lanceros-Mendez, Senentxu
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Polymer blends based on poly(vinylidene fluoride-trifluoroethylene)/poly(ethylene oxide), P(VDFTrFE)/PEO for Li-ion battery separator applications have been prepared through solvent casting technique. The microstructure, hydrophilicity and electrolyte uptake strongly depend on PEO content within the blend. The best value of ionic conductivity at room temperature was 0.25 mS cm−1 for the 60/40 membrane. The membranes are electrochemically stable., This work is funded by FEDER funds through the "Programa Operacional Factores de Competitividade - COMPETE" and by national funds by FCT - Fundacao para a Ciencia e a Tecnologia, project references Project PTDC/CTM/69316/2006, NANO/NMed-SD/0156/2007 and Pest-C/QUI/UIO686/2011 and grant SFRH/BD/68499/2010 (C.M.C) and SFRH/BD/66930/2009 CIBER-BBN is an initiative funded by the VI National R&D&D&i Plan 2008-2011, Iniciativa Ingenio 2010, Consolider Program, CIBER Actions and financed by the Instituto de Salud Carlos III with assistance from the European Regional Development Fund.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fatigue prediction in fibrin poly-epsilon-caprolactone macroporous scaffolds

  • Panadero, Juan Alberto
  • Vikingsson, Line Karina Alva
  • Sencadas, Vitor Joao Gomes Da Silva
  • Lanceros-Mendez, Senentxu
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Tissue engineering applications rely on scaffolds that during its service life, either for in-vivo or in vitro applications, are under loading. The variation of the mechanical condition of the scaffold is strongly relevant for cell culture and has scarcely been addressed. The fatigue life cycle of poly-epsilon-caprolactone, PCL, scaffolds with and without fibrin as filler of the pore structure were characterized both dry and immersed in liquid water. It is observed that the there is a strong increase from 100 to 500 in the number of loading cycles before collapse in the samples tested in immersed conditions due to the more uniform stress distributions within the samples, the fibrin loading playing a minor role in the mechanical performance of the scaffolds., This work is funded by FEDER funds through the "Programa Operacional Factores de Competitividade - COMPETE" and by national funds arranged by FCT-Fundacao para a Ciencia e Tecnologia, project references NANO/NMed-SD/0156/2007, PTDC/CTM-NAN/112574/2009 and PEST-C/FIS/UI607/2011. The authors also thank funding from "Matepro-Optimizing Materials and Processes", ref. "NORTE-07-0124-FEDER-000037", co-funded by the "Programa Operacional Regional do Norte" (ON.2 - O Novo Norte), under the "Quadro de Referencia Estrategico Nacional" (QREN), through the "Fundo Europeu de Desenvolvimento Regional" (FEDER). JAP and VS thank the FCT for the SFRWBD/64586/2009/ and SFRWBPD/63148/2009 grants, respectively. JLGR acknowledge the support of the Spanish Ministry of Science and Innovation through project No. MAT2010-21611-C03-01 (including the FEDER financial support). CIBER-BBN is an initiative funded by the VI National R&D&i Plan 2008-2011, Iniciativa Ingenio 2010, Consolider Program, GIBER Actions and financed by the Instituto de Salud Carlos III with assistance from the European Regional Development Fund.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tailoring the morphology and crystallinity of poly(L-lactide acid) electrospun membranes

  • Ribeiro, Clarisse
  • Sencadas, Vitor Joao Gomes Da Silva
  • Miguel Costa, Carlos
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
  • Lanceros-Mendez, Senentxu
[EN] Biodegradable poly(L-lactic acid) (PLLA) microfibers were prepared by electrospinning by varying the applied potential, solution flow rate and collector conditions. PLLA fibers with smoothly oriented and random morphologies were obtained and characterized by scanning electron microscopy. The optimum fiber orientation was obtained at 1000 rpm using a 20.3 cm diameter collecting drum, while for higher and lower drum rotation speeds, the rapid random motion of the jets resulted in a random fiber distribution. The deformation of the jet with rapid solidification during electrospinning often results in a metastable phase. PLLA electrospun fibers are amorphous but contain numerous crystal nuclei that rapidly grow when the sample is heated to 70-140 °C. In this way, the degree of crystallinity of the fibers can be tailored between 0 and 50% by annealing. Infrared transmission spectra revealed that the processing conditions do not affect the PLLA samples at the molecular level and that the crystallinity of the samples is related to the presence of ¿-crystals. © 2011 National Institute for Materials Science., SEM observations were conducted by the authors with the kind help of Jose Carlos Rodriguez from the Microscopy Service of Universidad Politecnica de Valencia, whose advice is greatly appreciated. We thank Centro for Nano and Microtechnologies (CeNTI), Famalicao, Portugal, for technical support and the Portuguese Foundation for Science and Technology (FCT) Grants PTDC/CTM/73030/2006, PTDC/CTM/69316/2006 and NANO/NMed-SD/0156/2007. VS thanks FCT for the SFRH/BPD/63148/2009 grant and CR thanks IINL for a PhD grant. JLGR acknowledges the support by the Spanish Ministry of Education through project No. MAT2010-21611-C03-01 (including FEDER financial support), by Centro de Investigacion Principe Felipe in the field of Regenerative Medicine through the collaboration agreement with Conselleria de Sanidad (Generalitat Valenciana) and Instituto de Salud Carlos III (Ministry of Science and Innovation).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Tailoring porous structure of ferroelectric poly(vinylidene fluoride-trifluoroethylene) by controlling solvent/polymer ratio and solvent evaporation rate

  • California, António
  • Cardoso, Vanessa F.
  • Costa, Carlos M.
  • Sencadas, Vitor
  • Botelho, Gabriela
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
  • Lanceros-Mendez, Senentxu
Ferroelectric macroporous poly(vinylidene fluoride-trifluoroethylene) membranes have been produced by isothermal crystallization from the solution at different temperatures starting from different diluted solutions of the co-polymer in dimethylformamide. In this way pore architecture, consisting in interconnected spherical pores can be obtained. The mechanism and kinetics of solvent evaporation was investigated and related to the evolution of the polymer microstructure. The mechanism underlying the pattern formation has been discussed on the light of the Flory-Huggins (FH) lattice theory, grain boundary effects and the Cahn-Hilliard equation for mass conservation systems. It was also observed that the temperature or initial concentration of the crystallization process does not affect the phase, ferroelectric transition temperature or the melting temperature of the polymer., The authors thank the Portuguese Foundation for Science and Technology (FCT) Grants PTDC/CTM-NAN/112574/2009, PTDC/CTM/73030/2006, PTDC/CTM/69316/2006 and NANO/NMed-SD/0156/2007. V.F., C.M.C. and V.S. thank the FCT for the SFRH/BD/44289/2008, SFRH/BD/68499/2010, SFRH/BPD/63148/2009 grants, respectively. JLGR acknowledge the funding from the Programa de Apoyo a la Investigacion y Desarrollo (PAID-00-09) of the Universidad Politecnica de Valencia for a short stay in Universidade do Minho, Braga, the support of the Spanish Ministry of Science through project No. MAT2010-21611-C03-01 (including the FEDER financial support) and funding for research in the field of Regenerative Medicine through the collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana), and the Institute de Salud Carlos III (Ministry of Science and Innovation). The authors wish also thank the CeNTI - Centre for Nanotechnology and Smart Materials, Rua Fernando Mesquita, 2782, 4760-034 Vila Nova de Famalicao, Portugal for allowing the use of some experimental equipment.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The role of solvent evaporation in the microstructure of electroactive beta-poly(vinylidene fluoride) membranes obtained by isothermal crystallization

  • Magalhaes, R.
  • Duraes, N.
  • Silva, M.
  • Silva, J.
  • Sencadas, V.
  • Botelho, G.
  • Lanceros Mendez, Senen
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Electroactive beta-poly(vinylidene fluoride) (PVDF) membranes were obtained by isothermal crystallization from the solution. Different morphologies and microstructures were obtained by crystallizing at different temperatures. The mechanism and kinetics of solvent evaporation from the polymeric solution were investigated using isothermal thermogravimetric analysis. The kinetic parameters and the activation energy were also calculated. The solvent evaporation is ruled by two steps, related with a metastable-unstable-metastable transition in the solution phase diagram. Scanning electron microscopy revealed the porous structure and the variations of the morphology with the variation of the isothermal evaporation temperature. Finally, the infrared spectroscopy measurements confirm that the polymer crystallizes in the electroactive beta-phase of PVDF., The authors thank the Portuguese Foundation for Science and Technology (FCT) Grants PTDC/CTM/73030/2006, PTDC/CTM/69316/2006, and NANO/NMed-SD/0156/2007. V. Sencadas thanks the FCT for the SFRH/BPD/63148/2009 grant. JLGR acknowledges the funding from the Programa de Apoyo a la Investigacion y Desarrollo (PAID-00-09) of the Universidad Politecnica de Valencia for a short stay in Universidade do Minho, Braga, the support of the Spanish Ministry of Science through project No. MAT2007-66759-C03-01 (including the FEDER financial support), and funding for research in the field of Regenerative Medicine through the collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana), and the Instituto de Salud Carlos III (Ministry of Science and Innovation). The authors also thank Solvay for providing the excellent quality material.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Physical-chemical properties of cross-linked chitosan electrospun fiber mats

  • Sencadas, Vitor Joao Gomes Da Silva
  • Correia, Daniela
  • Ribeiro, Clarisse
  • Moreira, S.
  • Botelho, G.
  • Lanceros Mendez, Senen
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Chitosan fiber mats were successfully processed by electrospinning. The as-spun fiber mats were neutralized with ethanol and cross-linked with glutaraldehyde. A decrease of the fiber average diameter from 243 +/- 43 nm down to 215.53 nm was observed for the neutralized and cross-linking chitosan membrane. It was found that the processing conditions do not alter the initial deacetylation degree of the polymer. Polymer crystallinity index showed a decrease from 61% for the Protasan material down to 17% for the cross-linking fiber mats. A swelling index up to 1000% was observed for the cross-linked samples. Preliminary MC-3T3-E1 cell culture results showed good cell adhesion and proliferation in the cross-linked chitosan fiber mats., This work is funded by FEDER funds through the "Programa Operacional Factores de Competitividade - COMPETE" and by national funds by FCT - Fundacao para a Ciencia e a Tecnologia, project references NANO/NMed-SD/0156/2007. V.S. and SM thanks the FCT grants SFRH/BPD/63148/2009 and SFRH/BPD/64726/2009, respectively. The authors also thank the support of the COST Action MP1003, 2010 'European Scientific Network for Artificial Muscles' (ESNAM). JLGR acknowledge the support of the Spanish Ministry of Science and Innovation through project No. MAT2010-21611-C03-01 (including the FEDER financial support) and Programa Nacional de Internacionalizacion de la I+D project EUI2008-00126. The authors also thank the National NMR Network (National Program for Scientific Re-equipment, REDE/1517/RMN/2005, funds from POCI 2010 (FEDER) and FCT) and Microscopy Service of the UPV for the use of their lab.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of electrospinning parameters on Poly(hydroxybutyrate) electrospun membranes fiber size and distribution

  • Correia, Daniela M.
  • Ribeiro, Clarisse
  • Ferreira, Jose C. C.
  • Botelho, Gabriela
  • Lanceros Mendez, Senen
  • Sencadas, Vitor
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Poly(hydroxybutyrate) (PHB) obtained from sugar cane waste was dissolved in a blend of chloroform and dimethylformamide (DMF) and electrospun at 40 degrees C. By adding DMF to the solution, the electrospinning process for the PHB polymer becomes more stable, allowing complete polymer crystallization during the jet travelling between the tip and the grounded collector. The influence of processing parameters on fiber size and distribution was systematically studied. It was observed that an increase of tip inner diameter promotes a decrease of the fiber average size and a broader distribution. Conversely, an increase of the electric field and flow rate produces an increase of fiber diameter until a maximum of similar to 2.0 mu m but for electric fields higher than 1.5 kV cm(-1), a decrease of the fiber diameter was observed. Polymer crystalline phase seems to be independent of the processing conditions and a crystallinity degree of 53% was found. Moreover, thermal degradation of the as-spun membrane occurs in single step degradation with activation energy of 91 kJ mol(-1). Furthermore, MC-3T3-E1 cell adhesion was not inhibited by the fiber mats preparation, indicating their potential use for biomedical applications., Contract grant sponsor: FEDER; contract grant sponsor: Programa Operacional Factores de Competitividade-COMPETE; contract grant sponsor: FCT-Fundacao para a Ciencia e a Tecnologia; contract grant numbers: NANO/NMed-SD/0156/2007, PTDC/CTM/73030/2006, and PTDC/CTM/69316/2006; contract grant sponsor: COST Action MP1003, 2010 'European Scientific Network for Artificial Muscles'; contract grant sponsor: FCT; contract grant numbers: SFRH/BPD/63148/2009 and SFRH/BD/82411/2011; contract grant sponsor: IINL; contract grant sponsor: Spanish Ministry of Science and Innovation (including the FEDER financial support); contract grant number: MAT2010-21611-C03-01; contract grant sponsors: VI National R&D&i Plan 2008-2011, Iniciativa Ingenio 2010, Consolider Program, and Instituto de Salud Carlos III (with assistance from the European Regional Development Fund).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessment of Parameters Influencing fiber characteristics of chitosan nanofiber membrane to optimize fiber mat productioi

  • Areias, A.C.
  • Gómez-Tejedor, José Antonio
  • Sencadas, V.
  • Alio, J.
  • Lanceros-Mendez, S.
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Electrospun chitosan nanofiber mats have been obtained using chitosan solutions in a mixture of trifluoroacetic acid and dichloromethane. The relationship between processing parameters (solvent composition, polymer concentration in the solution, feeding rate, applied voltage, traveling distance between the needle, and the collector) and fiber morphology was studied. Taguchi's methodology was followed to determine which parameters have the strongest influence on mean fiber diameter and fiber homogeneity. Chitosan nanofibers obtained with this procedure were water soluble due to the protonation of amine side groups but were successfully neutralized by immersion in calcium carbonate solutions. It was established that fiber diameter is mainly determined by the solution concentration and the distance from the needle to the collector while other parameters have less influence. The set of parameters that produce the thinnest fibers were a concentration of 8 wt%, a TFA/DCM ratio of 80:20 (v/v%), a voltage of 30 kV, a flow rate of 6.0 mL/h, a gap distance of 10 cm, using a needle diameter of 0.5, allowing to produce randomly oriented mats with a mean fiber thickness of 66 nm. © 2012 Society of Plastics Engineers., Contract grant sponsor: Portuguese Foundation for Science and Technology (FCT); contract grant number: NANO/NMed-SD/0156/2007; Contract grant sponsor: FCT; contract grant number: SFRH/BPD/63148/2009; Contract grant sponsor: Spanish Ministry of Science and Innovation; contract grant number: MAT2010-21611-C03-01; Contract grant sponsor: Programa Nacional de Internacionalizacion de la I+D; contract grant number: EUI2008-00126; Contract grant sponsors: Regenerative Medicine collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana), and the Instituto de Salud Carlos III (Ministry of Science and Innovation); Contract grant sponsors: Spanish Ministry of Science and Innovation, Centro para el Desarrollo Tecnologico Industrial (CDTI), CENIT: "Customized Eye Care'' and CeyeC; contract grant number: CEN-20091021; Contract grant sponsor: The translation of this paper was funded by the Universitat Politecnica de Valencia, Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of crystallinity and fiber orientation on hydrophobicity and biological response of poly(L-lactide) electrospun mats

  • Areias, A.C.
  • Ribeiro, Clarisse
  • Sencadas, Victor
  • Garcia Giralt, Natalia
  • Diez Perez, A.
  • Lanceros Mendez, Senen
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
[EN] Poly(L-lactide) electrospun mats have been produced with random and aligned fiber orientation and degrees of crystallinity from 0 up to nearly 50%. These two factors, fiber alignment and degree of crystallinity, strongly affect the hydrophobicity of the samples, this being larger for the aligned fiber mats and for the fibers with a higher degree of crystallinity. Whereas, the first effect can be associated with a decrease in the degree of porosity, the second should be related to an increase in fiber stiffness as the observed fiber roughness variations do not show strong differences between the samples. Proliferation of human chondrocytes cultured in a monolayer on these substrates is similar in both aligned and non-aligned amorphous mats. Crystallization of the aligned mats, on the other hand, nearly suppresses proliferation and the cells produce higher amounts of aggrecan, characteristic of the extracellular matrix of hyaline cartilage., This work is funded by FEDER funds through the "Programa Operacional Factores de Competitividade - COMPETE'' and by national funds by FCT (Fundacao para a Ciencia e a Tecnologia, project references PTDC/CTM/69316/2006, PTDC/CTM-NAN/112574/2009, and NANO/NMed-SD/0156/2007). V.S. thanks the FCT for the SFRH/BPD/63148/2009 grant. C. R. thanks the IINL for the financial support via a PhD grant. NG thanks Red Tematica de Investigacion Cooperativa en Envejecimiento y Fragilidad (RETICEF), which is an initiative of the ISCIII and the Catalan Government (2009SGR00848). JLGR acknowledges the support of the Spanish Ministry of Education through project No. MAT2010-21611-C03-01 (including the FEDER financial support). The authors thank the support from the COST Action MP1003, 2010, 'European Scientific Network for Artificial Muscles' (ESNAM).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Relaxation dynamics of poly(vinylidene fluoride) studied by dynamical mechanical measurements and dielectric spectroscopy

  • Sencadas, V.
  • Lanceros-Mendez, S.
  • Andrio Balado, A.
  • Sabater i Serra, Roser|||0000-0002-5550-7066
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
[EN] The aim of this study is to analyze the mobility of polymer chains in semicrystalline poly(vinylidene fluoride) (PVDF). PVDF crystallizes from the melt in the crystalline phase. The transformation from the phase to the electroactive phase can be induced by stretching at temperatures in the range between 80 and 140 ◦C. The spherulitic structure of the crystalline phase is deformed during stretching to form fibrils oriented in the direction of the strain. The amorphous phase confined among the crystalline lamellae is distorted as well and some degree of orientation of the polymer chains is expected. Dynamicmechanical and dielectric spectroscopy measurements were performed in PVDF films stretched to strain ratios up to 5 at temperatures between 80 and 140 ◦C. Dynamic-mechanical measurements were conducted between −60 ◦C and melting and in this temperature range the relaxation spectra show the main relaxation of the amorphous phase (called -relaxation) and at higher temperatures a relaxation related to crystallites motions (c-relaxation). Although the mean relaxation times of the -relaxation are nearly equal in PVDF before and after crystal phase transformation, a significant change of shape of the relaxation spectrum proves the effect of chain distortion due to crystal reorganization. In stretched PVDF the elastic modulus of the polymer in the direction of deformation is significantly higher than in the transversal one, as expected by chain and crystals fibril orientation. The recovery of the deformation when the sample is heated is related with the appearance of the c-relaxation. Dielectric spectroscopy spectrum shows the main relaxation of the amorphous phase and a secondary process (-relaxation) at lower temperatures. Stretching produces significant changes in the relaxation processes, mainly in the strength and shape of the main relaxation. The Havriliak-Negami function has been applied to analyze the dielectric response., This work is funded by FEDER funds through the "Programa Operacional Factores de Competitividade-COMPETE" and by national funds by FCT-Fundacao para a Ciencia e Tecnologia, project references NANO/NMed-SD/0156/2007, PTDC/CTM/69316/2006 and PTDC/CTM-NAN/112574/2009. V. S. thanks the FCT for the SFRH/BPD/63148/2009 grant. JLGR acknowledges the support of the Spanish Ministry of Science and Innovation through MAT2010-21611-C03-01 (including the FEDER financial support), and EUI2008-00126 projects and funding in the Centro de Investigacion Principe Felipe in the field of Regenerative Medicine through the collaboration agreement from the Conselleria de Sanidad (Generalitat Valenciana), and the Instituto de Salud Carlos III (Ministry of Science and Innovation). The authors also acknowledge support from the COST Action MP1003, 2010 "European Scientific Network for Artificial Muscles".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrical and thermal behavior of gamma-phase poly(vinylidene fluoride)/NaY zeolite composites

  • Lopes, A. C.
  • Caparros, C.
  • Neves, I. C.
  • Lanceros-Mendez, Senentxu
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Poly(vinylidene fluoride), PVDF, based composites with increasing NaY zeolite content up to 32 wt.% have been processed by solvent casting and melt crystallization. Depending on the melting temperature of the polymer, the composite crystallizes in the electroactive gamma or non electroactive a-phase of the polymer. The dielectric constant at room temperature reaches values larger that 1000 for the 32 wt.% composite at 1 kHz and it is mainly attributed to restricted ion mobility and interfacial polarization effects due to the zeolite inclusion, leading also to high dielectric losses. For the higher zeolite concentrations the composite d.c. electrical conductivity is characterized by two conducting regimes separated by a concentration independent breaking voltage of 4 V, which is associated to an intrazeolite charge transport., This work is funded by FEDER funds through the "Programa Operacional Factores de Competitividade - COMPETE" and by National funds by FCT- Fundacao para a Ciencia e a Tecnologia, Project references NANO/NMed-SD/0156/2007, PTDC/CTM/69316/2006, PEst-C/QUI/L110686/2011 and PTDC/CTM-NAN/112574/2009. ACL thanks the FCT for the Grant SFRH/BD/62507/2009. The authors also thank support from the COST Action MP1003, the 'European Scientific Network for Artificial Muscles' (ESNAM).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Composition-dependent physical properties of poly[(vinylidene fluoride)-co-trifluoroethylene] poly(ethylene oxide) blends

  • Costa, Carlos M.
  • Tamano Machiavello, M.N.
  • Lanceros Mendez, Senen
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Polymer blends based on poly(vinylidene fluoride-co-trifluoroethylene) copolymers, P(VDF-TrFE), and poly(ethylene oxide), PEO, with varying compositions have been prepared by solvent casting. In this way, P(VDF-TrFE) crystallizes from the solution while solvent evaporates, while PEO crystallizes from the melt during cooling to room temperature. The surface morphology of the polymer blends indicates the transition from the fibrillar microstructure typical of PVDF-TrFE to the spherulite structure characteristic of PEO. The vibration mode characteristics of P(VDF-TrFE) are not influenced by the presence of PEO in the polymer blend. Confinement of PEO in the P(VDF-TrFE) phase change the conformation of PEO from trans to helix, increasing this transformation for increasing P(VDF-TrFE) content in the polymer blends. Sequential crystallization of the two polymers produce separated amorphous phases whose independent cooperative conformational motions are revealed by two main dynamic-mechanical relaxations. No chemical interaction seems to exist between the polymers within the blend., This study is funded by FEDER funds through the "Programa Operacional Factores de Competitividade - COMPETE'' and by national funds by FCT-Fundacao para a Ciencia e a Tecnologia, Project References NANO/NMed-SD/0156/2007 and PTDC/CTM/69316/2006. C. M. C. also thanks the FCT for the Grant SFRH/BD/68499/2010. The authors also thank support from the COST Action MP1003, the "European Scientific Network for Artificial Muscles'' (ESNAM). JLGR acknowledges the support of the Spanish Ministry of Education through Project No. MAT2010-21611-C03-01 (including the FEDER financial support). CIBER-BBN is an initiative funded by the VI National R&D&D&i Plan 2008-2011, Iniciativa Ingenio 2010, Consolider Program, CIBER Actions and financed by the Instituto de Salud Carlos III with assistance from the European Regional Development Fund.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of fiber diameter and crystallinity on the stability of electrospun poly(L-lactic acid) membranes to hydrolytic degradation

  • Dias, Juliana C.
  • Ribeiro, Clarisse
  • Sencadas, V.
  • Botelho, G.
  • Lanceros Mendez, Senentxu
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
Hydrolytic degradation of electrospun mats of poly(l-lactic acid), PLLA, as a function of crystallinity and fiber diameter has been studied. The degradation in a saline phosphate buffer solution (PBS) up to 20 weeks produced a slight decrease in the sample mass but a clear decrease of the polymer average molecular weight in the amorphous fibers. This effect decreases as crystallinity increases. It is important for applications that morphological characteristics of the membranes such as average fiber diameter and membrane porosity are also affected by the degradation process. Fiber diameter increases while membrane porosity decreases, resulting in closer packed fibers due to the release of internal tensions related to the electrospinning and/or thermal treatment processes., This work is funded by FEDER funds through the "Programa Operacional Factores de Competitividade - COMPETE" and by national funds arranged by FCT - Fundacao para a Ciencia e a Tecnologia, project references NANO/NMed-SD/0156/2007, PTDC/CTM/73030/2006 and PTDC/CTM/69316/2006. The authors also thank support from the COST Action MP1003, 2010 'European Scientific Network for Artificial Muscles'. V.S. thanks the FCT for the SFRH/BPD/63148/2009 grant. C. R. thanks the Iberian Institute of Nanotechnology Laboratory (IINL) for a PhD grant. JLGR acknowledge the support of the Spanish Ministry of Education through project No. MAT2010-21611-C03-01 (including the FEDER financial support).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Processing and characterization of alpha-elastin electrospun membranes

  • Araujo, J.
  • Padrao, J.
  • Silva, J. P.
  • Dourado, F.
  • Correia, D. M.
  • Botelho, G.
  • Lanceros-Mendez, S.
  • Sencadas, V.
  • Gómez Ribelles, José Luís|||0000-0001-9099-0885
[EN] Elastin isolated from fresh bovine ligaments was dissolved in a mixture of 1,1,1,3,3,3-Hexafluoro-2-propanol and water were electrospun into fiber membranes under different processing conditions. Fiber mats of randomly and aligned fibers were obtained with fixed and rotating ground collectors and fibrils were composed by thin ribbons whose width depends on electrospinning conditions; fibrils with 721 nm up to 2.12 ¿m width were achieved. After cross-linking with glutaraldehyde, ¿-elastin can uptake as much as 1700 % of PBS solution and a slight increase on fiber thickness was observed. The glass transition temperature of electrospun fiber mats was found to occur at ~80 °C. Moreover, ¿-Elastin showed to be a perfect elastomeric material, and no mechanical hysteresis was found in cycle mechanical measurements. The elastic modulus obtained for random and aligned fibers mats in a PBS solution was 330±10 kPa and 732±165 kPa, respectively. Finally, the electrospinning and cross-linking process does not inhibit MC-3T3-E1 cell adhesion. Cell culture results showed good cell adhesion and proliferation in the cross-linked elastin fiber mats., This work is funded by FEDER funds through the "Programa Operacional Factores de Competitividade-COMPETE" and by national funds arranged by FCT-Fundacao para a Ciencia e a Tecnologia, project references NANO/NMed-SD/0156/2007, PTDC/CTM-NAN/112574/2009, and PEST-C/FIS/UI607/2011. The authors also thank funding from "Matepro-Optimizing Materials and Processes", ref. "NORTE-07-0124-FEDER-000037", cofunded by the "Programa Operacional Regional do Norte" (ON.2-O Novo Norte), under the "Quadro de Referencia Estrategico Nacional" (QREN), through the "Fundo Europeu de Desenvolvimento Regional" (FEDER). The authors also thank support from the COST Action MP1003, 2010 'European Scientific Network for Artificial Muscles'. VS, JP, JS, and DMC thank the FCT for the SFRH/BD/48708/2008, SFRH/BD/64901/2009, SFRH/BPD/64958/2009 and SFRH/BPD/63148/2009, and SFRH/BD/82411/2011 grants, respectively. JLGR acknowledges the support of the Spanish Ministry of Science and Innovation through project No. MAT2010-21611-C03-01 (including the FEDER financial support). CIBER-BBN is an initiative funded by the VI National R&D&i Plan 2008-2011, Iniciativa Ingenio 2010, Consolider Program, CIBER Actions and financed by the Instituto de Salud Carlos III with assistance from the European Regional Development Fund.