Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Nanoindentation study of WC-12Co hardmetals obtained from nanocrystalline powders: Evaluation of hardness and modulus on individual phases

  • Bonache, V.
  • E. Rayón|||0000-0002-0653-2046
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Busquets Mataix, David Jeronimo|||0000-0001-5031-7805
[EN] With the development of finer hardmetals, the study of mechanical properties of the different constituents down the micrometric level is a question of concern for materials optimization. Nanoindentation has been developed in last years in order to cope with mechanical characterisation at the nanolevel, but difficulties on phase detection are an issue. In the present work, individual hardness and Young's modulus of the constituents of WC-12Co composite were obtained by the use of very shallow nanoindentations (30 nm depth), with the aid of in situ 3D imaging to identify these. By this method three different phases at the sub-micrometric level have been identified and characterised: namely cobalt matrix, tungsten carbide and eta phase. The presence of the latter phase and its characterisation is of paramount importance in understanding the behaviour of hardmetals. Values of hardness from 8 (cobalt matrix) to 25 GPa (eta phase) have been obtained. Also, for these phases Young's modulus varied from 250 to 400 GPa respectively. Furthermore, it is firstly reported these values for the WC prismatic planes (1 0 1 0) being in the range of 40-55 and 700-900 GPa respectively. These values decrease to a hardness in the range of 25-30 GPa and modulus in the range from 450 to 550 GPa for the WC basal plane {0 0 0 1}. (C) 2010 Elsevier B.V. All rights reserved., This work has been supported by CICYT, Spain, through project number MAT2006-12945-C03-02 and Generalitat Valenciana, through project number ACOMP/2009/221.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fabrication of ultrafine and nanocrystalline WC-Co mixtures by high energy milling

  • Bonache Bezares, Victoria
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Busquets Mataix, David Jeronimo|||0000-0001-5031-7805
  • Segovia-López, Francisco|||0000-0002-4143-5751
[EN] In this work ultrafine and nanocrystalline WC-Co mixtures were obtained by low energy milling in planetary ball mill. The effect of the processing conditions on the reduction and distribution of the grain sizes and the internal strains level were studied. The characterisation of the powder mixtures was performed by means of scanning and transmission electron microscopy and X-ray diffraction analysis. Observations through SEM and TEM images showed a particle size below 100 nm, after milling. The X-ray diffraction profile analysis revealed a WC phase refined to a crystallite size of 19 nm. The mixtures obtained have been consolidated and mechanical and microstructurally characterised. The results show improvements in resistant behaviour of the material consolidated from nanocrystalline powders, in spite of the grain growth experienced during the sintering. The best results were found for the material obtained by wet milling during 100 h, which presents values of hardness higher than 1800 HV. © 2011 Institute of Materials, Minerals and Mining., This work has been supported by CICYT, Spain, through project no. MAT2006-12945-C03-02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of plasma intensity on wear and erosion resistance of conventional and nanometric WC-Co coatings deposited by APS

  • Bonache Bezares, Victoria
  • García, J.C.
  • Sánchez, E.
  • Bannier, E.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
The effects of plasma intensity and powder particle size on wear and erosion resistance have been evaluated for WC-12 wt.%Co coatings deposited by Air Plasma Spraying. Coatings were deposited from micrometric and nanostructured powders. SEM and XRD characterization showed the presence of WC, W 2C, W, and an amorphous Co-rich matrix. The performance of the different coatings was compared in sliding wear tests (ball-on-disk), under dry friction conditions. Wear debris and tracks were analyzed by SEM. The debris generated during the test was found to have a great influence on the sliding properties. Wear follows a "three-body abrasive mechanism" and is dominated by coating spallation because of sub-surface cracking. In order to evaluate erosion behavior, solid particle erosion tests were conducted. Eroded coatings were analyzed by SEM, and erosion mainly occurs by a "cracking and chipping mechanism." The study shows that wear and erosion behavior is strongly affected by plasma arc intensity. © 2010 ASM International., This study has been conducted with the support of the Spanish Ministry of Education and Science under projects MAT 2006-12945 and MAT 2009-14144.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Preparation and spray drying of Al2O3-TiO2 nanoparticle suspensions to obtain nanostructured coatings by APS

  • Sánchez, E.
  • Moreno, A.
  • Vicent, M.
  • Bonache Bezares, Victoria
  • Santacruz, I.
  • Moreno, R.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Klyatskina, Elizaveta
[EN] Al2O3-TiO2 coatings were deposited on austenitic stainless steel coupons from nanostructured powders by atmospheric plasma spraying (APS). Commercial suspensions of nanosized Al2O3 and TiO2 particles were used as starting materials. Mixtures of these suspensions and of more concentrated suspensions of Al2O3 and TiO2 were then agglomerated into plasma sprayable feedstock. Agglomeration was performed by spray drying, followed by consolidation thermal treatment. These powders were successfully deposited, yielding coatings that were well bonded to the substrates. The coating microstructure thus consisted of semi-molten feedstock agglomerates surrounded by fully molten particles that acted as binders. Agglomerates from suspensions with higher solids contents yielded coatings with lower porosity and fewer semi-molten areas. (C) 2010 Elsevier B.V. All rights reserved., This work has been supported by the Spanish Ministry of Science and Innovation (projects MAT2006-12945-C03-01-02 and CIT-420000-2008-2), and the Institute of Small and Medium-sized Enterprise (IMPIVA) of the Autonomous Government of Valencia through the European Social Fund (ESF) Operational Programme for the Valencia Region 2007–2013 and a Complementary Action (ACOMP/2009/221).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Characterization of nanostructured ceramic and cermet coatings deposited by plasma spraying

  • Sanchez, Enrique
  • Bannier, Emilie
  • Vicent, Mónica
  • Moreno, Arnaldo
  • Bonache Bezares, Victoria
  • Boccaccini, Aldo R.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Klyatskina, Elizaveta
[EN] Industry has a growing need of advanced coatings for a variety of applications (aerospace, special machinery, medicine, etc.). Nanostructured coatings have the potential of providing novel materials with enhanced properties. This paper describes the results of recent research on wear-resistant nanostructured coatings. Cermet (WC-Co) and ceramic (Al(2)O(3)-TiO(2)) coatings were obtained by atmospheric plasma spraying. Coating microstructure and phase composition were characterized using scanning electron microscopy, X-ray energy-dispersion microanalysis, and X-ray diffraction techniques. Vickers microhardness (H(V)) of the coatings was also measured. The microstructure and properties of the developed nanostructured coating were compared with those of their conventional counterparts. The influence of the substrate on both microstructure end properties was investigated, as the coatings were deposited on two different steels. In the WC-Co coatings, significant decomposition of the WC particles occurred during spraying, which is prejudicial to wear resistance. Nanostructured Al(2)O(3)-TiO(2) coatings exhibited a bimodal microstructure that retained the initial nanostructure of the powder. The presence of these areas leads to better tribological properties., This work was financially supported by the Spanish Minister for Sciences and Innovation (Project: MAT2006-12945-C03).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Friction and wear behaviour of WC-Co-Cr3C2-VC cemented carbides obtained from nanocrystalline mixtures

  • Espinosa, L.
  • Bonache Bezares, Victoria
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
The effect of adding Cr3C2, VC or a mixture of both as a grain growth inhibitors to cemented carbides obtained from WC-12 wt.%Co nanocrystalline mixtures on the behaviour of friction and dry sliding wear have been studied. All the wear tests were performed on a tribometer with ball on disc configuration, using a WC-6 wt.%Co ball as a counterpart with normal contact loads of 40 and 60 N, sliding distance of 2000 m and a sliding speed of 0.1 m/s. A significant reduction in the wear rates was observed by the effect of the aforementioned additives, in particular for the VC, which showed an increase in the wear resistance of the order of 90%. The analysis of wear and surface damage were correlated to the observed behaviour., The authors would like to thank the Ministry of Education and Science, and the support received through the Projects MAT2006-12945-C03-02 and MAT2009-14144-C03-02, as well as the AECI for the realization of the doctoral thesis by L. Espinosa in the ITM of the UPV.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Microstructural control of ultrafine and nanocrystalline WC-12Co-VC/Cr3C2 mixture by spark plasma sintering

  • Bonache Bezares, Victoria
  • García-Rocha, Victoria
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
The aim of this present work is to study the effect of VC and/or Cr 3C 2 in densification, microstructural control and mechanical behaviour of WC-12Co ultrafine and nanocrystalline mixtures, consolidated by spark plasma sintering at 1100 °C, applying a pressure of 80 MPa in combination with a heating rate of 100 °C min -1. Nanocrystalline and ultrafine mixtures with an average size of 30 nm and 100-250 nm, respectively, with the addition of 1 and 0.5 wt.% of VC/Cr 3C 2 grain growth inhibitors, respectively, were investigated. The density, microstructure, hardness and fracture toughness of the consolidated samples were measured and observed. The addition of VC inhibitor allows an excellent grain growth control keeping microstructures with an average grain size of 154 nm. The hardness values and fracture toughness obtained were about 2000 HV 30 and above 10 MPa m 1/2, respectively. © 2010 Elsevier Ltd and Techna Group S.r.l., The work is supported financially by the Spanish Ministry of Science and Innovation by means of the project MAT 2006-12945-C02. A. Borrell, is grateful to this Ministry for the mobility grant to the Institute of Materials Technology (ITM) of the Polytechnical University of Valencia, Spain.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Hardness and Young&apos, s modulus distributions in atmospheric plasma sprayed WC-Co coatings using nanoindentation

  • E. Rayón|||0000-0002-0653-2046
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Bonache Bezares, Victoria
  • Roa, J. J.
  • Sánchez, E.
A statistical indentation analysis of WC-Co coatings obtained by atmospheric plasma spray (APS) with two secondary plasma gases, H 2 and He, was investigated using an instrumented indentation technique with the aim of correlating the influence of the nanomechanical behaviour of each constituent phase with the micromechanical characteristics of these coatings.X-ray diffraction (XRD) and backscattered electron (BSE) analysis showed that H 2 gas produced a greater decarburisation of the WC phase. The dissolution and decomposition of the WC phase during the process produced a Co+W+C solid solution as binder phase and the formation of W 2C and W as secondary phases. The nanohardness (H) and Young's modulus (E) resulting from a grid of 300 indentations performed at 50nm in depth identified the characteristics of each phase in the heterogeneous structure produced by decarburisation. Statistical study by a CDF fit and Gaussian simulated distributions showed that the mechanical properties of the coatings were governed by the binder phase content, which decreased the possible hardening effect of the arising hardest phases (W 2C and Co+W+C solid solution). © 2011 Elsevier B.V., Dr. E. Rayon particularly wishes to thank Marcos Signes for his help and discussion of the results of this study. The work was financially supported by the Spanish Ministry of Science and Innovation (MAT2006-12945-C03-02 and MAT2009-14144-C03-02) and the Autonomous Government of Valencia (ACOMP/2009/221 and ACOMP/2010/025).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fabrication of full density near-nanostructured cemented carbides by combination of VC/Cr3C2 addition and consolidation by SPS and HIP technologies

  • Bonache Bezares, Victoria
  • Fernández Valdés, Adolfo
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
The aim of present work is to study the effect of VC and/or Cr3C2 in densification, microstructural development and mechanical behavior of nanocrystalline WC-12wt.%Co powders when they are sintered by spark plasma sintering (SPS) and hot isostatic pressing (HIP). The results were compared to those corresponding to conventional sintering in vacuum. The density, microstructure, X-ray diffraction, hardness and fracture toughness of the sintered materials were evaluated. Materials prepared by SPS exhibits full densification at lower temperature (1100 degrees C) and a shorter stay time (5 min), allowing the grain growth control. However, the effect of the inhibitors during SPS process is considerably lower than in conventional sintering. Materials prepared by HIP at 1100 degrees C and 30 min present full densification and a better control of microstructure in the presence of VC. The added amount of VC allows obtaining homogeneous microstructures with an average grain size of 120 nm. The hardness and fracture toughness values obtained were about 2100 HV30 and close to 10 MPa m(1/)2, respectively. (C) 2010 Elsevier Ltd. All rights reserved., The work is supported financially by the Spanish Ministry of Science and Innovation by means of the project MAT 2006-12945-C03-C02 and MAT 2009-14144-C03-C02.