Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 17
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Compressibility and structural stability of ultra-incompressible bimetallic interstitial carbides and nitrides

  • Errandonea, D.
  • Ruiz-Fuertes, J.
  • Sans, J. A.
  • Santamaría-Perez, D.
  • Gómez, A.
  • Sapiña, F.
  • Gomis, O.|||0000-0001-6763-0638
We have investigated by means of high-pressure x-ray diffraction the structural stability of Pd 2Mo 3N, Ni 2Mo 3C 0.52N 0.48, Co 3Mo 3C 0.62N 0.38, and Fe 3Mo 3C. We have found that they remain stable in their ambient-pressure cubic phase at least up to 48 GPa. All of them have a bulk modulus larger than 330 GPa, the least compressible material being Fe 3Mo 3C, B 0 = 374(3) GPa. In addition, apparently a reduction of compressibility is detected as the carbon content is increased. The equation of state for each material is determined. A comparison with other refractory materials indicates that interstitial nitrides and carbides behave as ultra-incompressible materials. © 2012 American Physical Society., Research supported by Spanish MCYT under Grants No. MAT2010-21270-C04-01, No. MAT2009-14144-CO3-03, and No. CSD2007-00045 (MALTA Consolider Team). XRD experiments carried out at the Diamond Light Source (I15 beamline, proposal EE6517).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Enhanced hydrothermal resistance of Y-TZP ceramics through colloidal processing

  • E. Rayón|||0000-0002-0653-2046
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Manjón, Francisco-Javier|||0000-0002-3926-1705
  • Moreno, R.
  • Alcazar, C.
  • Jimenez-Pique, E.
  • Llanes, L.
Two commercial zirconia powders with 3mol% of yttria (TZ3YE and TZ3YS, labeled as ZE and ZS, respectively) supplied by Tosoh (Japan) were used for this study. Maximum colloidal stability for ZE was achieved by dispersing the powders in a mixture of water/ethanol of 90:10 (wt/wt) using a sonication probe. The rheological behavior of the suspensions was optimized in terms of solids content ranging from 20 to 33vol% and sonication time (06min), the best results being obtained after 2min. ZS samples were prepared to a solids loading of 30vol% in water dispersing with 2min-sonication. Samples obtained by slip casting in plaster molds were used for dynamic sintering studies, and fully dense and nanostructured specimens were obtained at temperatures of 1300 degrees C1350 degrees C (ZE samples) and 1400 degrees C per 2h (ZS samples). The Hardness (H) and Young's Modulus (E) properties of the specimens were studied by nanoindentation technique giving 17 and 250GPa mean values for H and E, respectively. The specimens were then forced to a low-temperature degradation (LTD) treatment at 130 degrees C for 240h in steps of 60h. Raman spectroscopy and nanoindentation results of hydrothermally treated samples showed the absence of transformation from tetragonal to monoclinic phase until 180h whereas the mechanical properties maintained constant even at the sample surface. After 240h of LTD, the monoclinic phase was detected on all specimens by Raman peaks centered at 180, 191, and 383cm1. The nanoindentation study revealed an important loss of mechanical features reaching 10 and 175GPa for H and E, respectively. In the case of the ZS specimens, no monoclinic phase is detected after 240h of LTD treatment and no decay of E or H is detected. The free defect microstructure reached for the ZS specimen revealed a higher hydrothermal resistance so that it is concluded that the excellent behavior against thermal degradation is possible due to the large uniformity obtained by colloidal processing rather than the particle size of the starting powders., This work has been supported by Spanish Ministry of Science and Innovation (Projects MAT2009-14144-C03-02, MAT2009-14369-C02-01, and MAT2008-03398). Authors thank Prof. M. Anglada for helpful comments and discussion. R Moreno thanks the Universidad Politecnica de Valencia for the concession of a grant in the frame of its Program of Support to R+D (PAID-02-11, R-1752). We also wish to acknowledge Rut Benavente for her excellent technical support.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of the feedstock characteristics on the microstructure and properties of Al2O3 TiO2 plasma-sprayed coatings

  • Vicent, M.
  • Bannier, E.
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Molina, T.
  • Moreno, R.
  • Sánchez, E.
[EN] Atmospheric plasma spraying (APS) is an interesting technique to obtain nanostructured coatings due to its versatility, simplicity and relatively low cost. However, nanometric powders cannot be fed into the plume using conventional feeding systems, due to their low mass and poor flowability, and must be adequately reconstituted into sprayable micrometric agglomerates. In this work, Al2O3–13 wt.%TiO2 nanostructured and submicron-nanostructured powders were deposited using APS. The feedstocks were obtained by spray drying from two starting suspensions, prepared by mixing two commercial nanosuspensions of Al2O3 and TiO2, or by adding nanosized TiO2 and submicron-sized Al2O3 powders to water. The spray-dried granules were heat-treated to reduce their porosity and the resultant powders were fully characterized. Optimization of the deposition conditions enabled the reconstituted powders to be successfully deposited, yielding coatings that were well bonded to the substrate. The coating microstructure, characterized by SEM, was formed by semi-molten feedstock agglomerates surrounded by fully molten particles that act as a binder. Moreover, microhardness, adhesion, and tribological behavior were determined, and the impact of the granule characteristics on these properties was studied. It was found that changing the feedstock characteristics allowed controlling the coating quality and properties., This work has been supported by the Spanish Ministry of Science and Innovation (project MAT2009-14144-C03).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Correlation of thermal conductivity of suspension plasma sprayed yttria stabilized zirconia coatings with some microstructural effects

  • Carpio, Pablo
  • Blochet, Quentin
  • Pateyron, Bernard
  • Pawlowski, Lech
  • Sanchez, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
Yttria-stabilized zirconia (3YSZ) coatings were successfully obtained by suspension plasma spraying. The coatings present generally two-zones-microstructure comprising nanostructured zones contributed by unmolten, partially sintered nanoparticles sintered surrounded by lamellar splats formed from molten and agglomerated in-flight fine solids. In addition, different types of cracks inside the coating microstructure were classified and quantified by image analysis such as e.g. inner microcracks and segmentation cracks associated with quenching process as well as horizontal interlamellar cracks. Thermophysical properties of sprayed coatings were tested with a thermal diffusivity set up basing onto light flash principle. Subsequently, the thermal conductivity was determined with the use of literature data of density and specific heat. The calculations showed very low thermal conductivities values. The values did not correlate with coatings porosity data. Consequently, the analysis of variance (ANOVA) test allowed evaluating the possible impact of the various types of cracks on thermal conductivity. By this analysis, a good correlation between vertical cracks, which include microcracks and segmentation cracks, and thermal conductivity was found. The findings also confirmed the increase of thermal conductivity associated with this type of cracks., This work has been supported by the Spanish Ministry of Science and Innovation (project MAT2009-14144-C03) and the Research Promotion Plan of the Universitat Jaume I, action 2.1 (ref. E-2011-05) and action 3.1 (ref. PREDOC/2009/10).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Sliding wear behavior of WC-Co-Cr3C2-VC composites fabricated by conventional and non-conventional techniques

  • Espinosa-Fernández, L.
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Gutierrez-González, C.F.
[EN] The present work aims are to study the dry sliding wear behavior of WC-12 wt.%Co materials, with or without addition of Cr3C2/VC grain growth inhibitors, and to sinter them by two different consolidation techniques: conventional sintering and spark plasma sintering (SPS). The dry sliding wear tests were performed on a tribometer with a ball-on-disc configuration using a WC-Co ball as a counterpart material with a normal contact load of 60 N, a sliding distance of 10000 m and a sliding speed of 0.1 m/s. The influence of the grain growth inhibitors and the consolidation techniques in sintered samples were related to the friction coefficient, wear rates and wear pattern damage. Samples sintered by non-conventional technique (SPS) show the best wear resistance and lower friction coefficient. The addition of inhibitors reduces the wear rates in materials consolidated by both techniques. The differences in the wear damage are related to microstructural parameters, mechanical properties and wear rates, The work is supported financially by the Spanish Ministry of Science and Innovation by the project MAT2009-14144-C03-C02. L. Espinosa-Fernández, acknowledges the AECI program for the realization of the Ph.D in the ITM-UPV. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Influence of plasma intensity on wear and erosion resistance of conventional and nanometric WC-Co coatings deposited by APS

  • Bonache Bezares, Victoria
  • García, J.C.
  • Sánchez, E.
  • Bannier, E.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
The effects of plasma intensity and powder particle size on wear and erosion resistance have been evaluated for WC-12 wt.%Co coatings deposited by Air Plasma Spraying. Coatings were deposited from micrometric and nanostructured powders. SEM and XRD characterization showed the presence of WC, W 2C, W, and an amorphous Co-rich matrix. The performance of the different coatings was compared in sliding wear tests (ball-on-disk), under dry friction conditions. Wear debris and tracks were analyzed by SEM. The debris generated during the test was found to have a great influence on the sliding properties. Wear follows a "three-body abrasive mechanism" and is dominated by coating spallation because of sub-surface cracking. In order to evaluate erosion behavior, solid particle erosion tests were conducted. Eroded coatings were analyzed by SEM, and erosion mainly occurs by a "cracking and chipping mechanism." The study shows that wear and erosion behavior is strongly affected by plasma arc intensity. © 2010 ASM International., This study has been conducted with the support of the Spanish Ministry of Education and Science under projects MAT 2006-12945 and MAT 2009-14144.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

ZrTiO4 materials obtained by Spark Plasma Reaction Sintering

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • García-Rocha, Victoria
  • Fernández, Adolfo
  • Gómez, Andrés
  • López-López, Emilio
  • Moreno, Rodrigo
Zirconium titanate (ZrTiO4), have many attractive properties such as high resistivity, high dielectric constant, high permittivity at microwave frequencies and excellent temperature stability for microwave properties. Zirconium titanate dense materials are proposed for many structural applications, but fully reacted and completely dense pieces are difficult to obtain by conventional routes. In this work, fully dense zirconium titanate materials ( 98%) were obtained at lower temperatures (1300 1400 C) and short processing time by non-conventional technique; spark plasma-reaction sintering (SPRS). Homogeneous and stable starting powders mixture with the adequate composition was prepared from the raw materials: m-ZrO2 ( 0.3 lm) and anatase-TiO2 ( 40 nm). Dense materials were mechanically and microstructural characterised. The fracture strength was measured by biaxial testing, giving values of about 200 MPa., This study has been supported by the Spanish Ministry of Science and Innovation MAT2009-14144-C03-02, MAT2012-38364-C03-02 and MAT2012-31090. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana for the BEST/2012/302 grant and the financial support for ACOMP/2012/166.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Enhanced properties of alumina-aluminium titanate composites obtained by spark plasma reaction-sintering of slip cast green bodies

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Rocha, Victoria G.
  • Fernandez, Adolfo
  • Molina, Tamara
  • Moreno, Rodrigo
Full dense alumina + 40 vol.% aluminium titanate composites were obtained by colloidal filtration and fast reaction-sintering of alumina/titania green bodies by spark plasma sintering at low temperatures (1250-1400 degrees C). The composites obtained had near-to-theoretical density (> 99%) with a bimodal grain size distribution. Phase development analysis demonstrated that aluminium titanate has already formed at 1300 degrees C. The mechanical properties such as Vickers hardness, flexural strength and fracture toughness of bulk composites are significantly higher than those reported elsewhere, e.g. the composite sintered at 1350 degrees C show values of about 24 GPa, 424 MPa and 5.4 MPa m(1/2), respectively. The improved mechanical properties of these composites are attributed to the enhanced densification and the finer and more uniform nanostructure achieved by non-conventional fast sintering of slip-cast dense green compacts. Crown Copyright (c) 2012 Published by Elsevier Ltd. All rights reserved., This study has been supported by the Spanish Ministry of Science and Innovation MAT2009-14369-C02-01 and MAT2009-14144-C03-02. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana for the BEST/2012/302 grant and the financial support for ACOMP/2012/166.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Friction and wear behaviour of WC-Co-Cr3C2-VC cemented carbides obtained from nanocrystalline mixtures

  • Espinosa, L.
  • Bonache Bezares, Victoria
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
The effect of adding Cr3C2, VC or a mixture of both as a grain growth inhibitors to cemented carbides obtained from WC-12 wt.%Co nanocrystalline mixtures on the behaviour of friction and dry sliding wear have been studied. All the wear tests were performed on a tribometer with ball on disc configuration, using a WC-6 wt.%Co ball as a counterpart with normal contact loads of 40 and 60 N, sliding distance of 2000 m and a sliding speed of 0.1 m/s. A significant reduction in the wear rates was observed by the effect of the aforementioned additives, in particular for the VC, which showed an increase in the wear resistance of the order of 90%. The analysis of wear and surface damage were correlated to the observed behaviour., The authors would like to thank the Ministry of Education and Science, and the support received through the Projects MAT2006-12945-C03-02 and MAT2009-14144-C03-02, as well as the AECI for the realization of the doctoral thesis by L. Espinosa in the ITM of the UPV.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Dense nanostructured zirconia compacts obtained by colloidal filtration of binary mixtures

  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Alcázar, M.C.
  • Moreno, R.
As starting materials two commercial nanosized zirconias doped with 3 mol% of Y 2O 3 were used: a powder of about 100 nm (TZ3YE, Tosoh, Japan) and a colloidal suspension of about 15 nm (Mel Chemicals, UK). Colloidal stability in water was studied for both zirconias in terms of zeta potential as a function of deflocculant concentration and pH. Concentrated suspensions were prepared by dispersing the powder in the colloidal suspension to solids loadings ranging from 5 to 30 vol.% using a sonication probe to achieve dispersion. The rheological behavior was optimized in terms of solids content, deflocculant content and sonication time. Optimized suspensions with up to 25 vol.% solids showed a nearly Newtonian behavior and extremely low viscosities and maintain stable for long times (days) which is an important drawback of conventional nanoparticle suspensions. Samples obtained by slip casting in plaster moulds were used for dynamic sintering studies and dense, nanostructured specimens were obtained at temperatures of 1300-1400°C., This work has been supported by Spanish Ministry of Science and Innovation (Projects MAT2009-14144-C03-02 and MAT2009-14369-C02-01). R. Moreno thanks to Universidad Politecnica de Valencia for the concession of a grant in the frame of its Programme of Support to R + D (PAID-02-11, R-1752).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Microstructure and photocatalytic activity of suspension plasma sprayed TiO2 coatings on steel and glass substrates

  • Bannier, E.
  • Darut, G.
  • Sánchez, E.
  • Denoirjean, A.
  • Bordes, M.C.
  • Ageorges, H.
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • E. Rayón|||0000-0002-0653-2046
In this study, TiO 2 coatings were deposited by suspension plasma spraying (SPS) from a commercial TiO 2 nanoparticle suspension on two different substrates: a standard stainless steel and a Pyrex glass. Coatings were sprayed on both substrates with an F4-MB monocathode torch; a Triplex Pro tricathode torch was also used to spray coatings just on the stainless steel substrates. Spraying distance and cooling were varied.The anatase content in the coatings, determined by XRD, ranged from 32 to 72 wt% A significant amount of anatase to rutile transformation was found to occur during cooling. Examination of the microstructure revealed that the coating microstructure was bimodal, involving a non-molten region consisting mainly of anatase nanoparticle agglomerates and a molten region. The glass substrate coatings displayed a segregated phase distribution, particularly when the surface to be coated was cooled. Photocatalytic activity was determined by a methylene blue test.The experimental data fitted well to a first-order kinetic. All the coatings exhibited high photocatalytic activity in comparison with that of a commercial sol-gel coating. However, unlike much of the previous research, photocatalytic activity did not correlate with the anatase content determined by XRD. © 2011 Elsevier B.V., This work has been supported by the Spanish Ministry of Science and Education (MAT2009-14144-C03-01), by the Spanish Ministry of Science and Innovation (PID-600200-2009-5) and by the European Commission in the frame of the Interreg IV B Sudoe programme (Eliare: SOE1/P1/F169).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Atmospheric plasma spraying coatings from alumina titania feedstockcomprising bimodal particle size distributions

  • Vicent, Mónica
  • Bannier, Emilie
  • Moreno, Rodrigo
  • Sanchez, Enrique
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
In this work, Al2O3 13 wt% TiO2 submicron-nanostructured powders were deposited using atmospheric plasma spraying. The feedstocks were obtained by spray drying two starting suspensions of different solids content, prepared by adding nanosized TiO2 and submicron-sized Al2O3 powders to water. The spray-dried granules were heat-treated to reduce their porosity and the powders were fully characterised in both untreated and thermally treated state. Comparison with two commercial feedstocks was carried out. Characterisation allowed a temperature for the thermal treatment to be chosen on the basis of the sprayability of the feedstock and the preservation as much as possible of the submicron-sized structure of the unfired agglomerates. Optimisation of the deposition conditions enabled the reconstituted powdrs to be successfully deposited, yielding coatings that were well bonded to the substrate. The coating microstructure, characterised by SEM, was mostly formed by a matrix of fully molten particles where the presence of semi-molten feedstock agglomerates was also observed. Moreover, microhardness, toughness, adhesion and tribological behaviours were determined, and the impact of the granule characteristics on these properties was studied. It was found that changing the feedstock characteristics allows controlling the coating quality and properties. In general, good mechanical properties were obtained using a feedstock comprising a binary mixture of submicrometric Al2O3 and nanometric TiO2 particles in the spray-dried powder, This work has been supported by Spanish Ministry of Economy and Competitiveness (MAT2009-14144-C03 and MAT2012-38364-C03).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Hardness and Young&apos, s modulus distributions in atmospheric plasma sprayed WC-Co coatings using nanoindentation

  • E. Rayón|||0000-0002-0653-2046
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Bonache Bezares, Victoria
  • Roa, J. J.
  • Sánchez, E.
A statistical indentation analysis of WC-Co coatings obtained by atmospheric plasma spray (APS) with two secondary plasma gases, H 2 and He, was investigated using an instrumented indentation technique with the aim of correlating the influence of the nanomechanical behaviour of each constituent phase with the micromechanical characteristics of these coatings.X-ray diffraction (XRD) and backscattered electron (BSE) analysis showed that H 2 gas produced a greater decarburisation of the WC phase. The dissolution and decomposition of the WC phase during the process produced a Co+W+C solid solution as binder phase and the formation of W 2C and W as secondary phases. The nanohardness (H) and Young's modulus (E) resulting from a grid of 300 indentations performed at 50nm in depth identified the characteristics of each phase in the heterogeneous structure produced by decarburisation. Statistical study by a CDF fit and Gaussian simulated distributions showed that the mechanical properties of the coatings were governed by the binder phase content, which decreased the possible hardening effect of the arising hardest phases (W 2C and Co+W+C solid solution). © 2011 Elsevier B.V., Dr. E. Rayon particularly wishes to thank Marcos Signes for his help and discussion of the results of this study. The work was financially supported by the Spanish Ministry of Science and Innovation (MAT2006-12945-C03-02 and MAT2009-14144-C03-02) and the Autonomous Government of Valencia (ACOMP/2009/221 and ACOMP/2010/025).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fabrication of full density near-nanostructured cemented carbides by combination of VC/Cr3C2 addition and consolidation by SPS and HIP technologies

  • Bonache Bezares, Victoria
  • Fernández Valdés, Adolfo
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
The aim of present work is to study the effect of VC and/or Cr3C2 in densification, microstructural development and mechanical behavior of nanocrystalline WC-12wt.%Co powders when they are sintered by spark plasma sintering (SPS) and hot isostatic pressing (HIP). The results were compared to those corresponding to conventional sintering in vacuum. The density, microstructure, X-ray diffraction, hardness and fracture toughness of the sintered materials were evaluated. Materials prepared by SPS exhibits full densification at lower temperature (1100 degrees C) and a shorter stay time (5 min), allowing the grain growth control. However, the effect of the inhibitors during SPS process is considerably lower than in conventional sintering. Materials prepared by HIP at 1100 degrees C and 30 min present full densification and a better control of microstructure in the presence of VC. The added amount of VC allows obtaining homogeneous microstructures with an average grain size of 120 nm. The hardness and fracture toughness values obtained were about 2100 HV30 and close to 10 MPa m(1/)2, respectively. (C) 2010 Elsevier Ltd. All rights reserved., The work is supported financially by the Spanish Ministry of Science and Innovation by means of the project MAT 2006-12945-C03-C02 and MAT 2009-14144-C03-C02.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

EPD and Spark Plasma Sintering of bimodal alumina/titania concentrated suspensions

  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Rocha, Victoria G.
  • Fernández, Adolfo
  • Molina, Tamara
  • Moreno, Rodrigo
Alumina-aluminium titanate (A-AT) composites and laminates have been recently investigated because they can provide improved flaw tolerance and toughness associated to a microcracking mechanism. A-AT composites have been produced by slip casting and reaction sintering of submicron sized alumina and titania powders. This work deals with the preparation of thick self-sustained A-AT films from mixtures of submicron sized alumina and nanosized titania powders and further sintering by conventional and non-conventional (spark plasma sintering, SPS) methods. Suspensions were prepared in water to high solid loadings, up to 50 vol.%. Self-sustained films were obtained by aqueous electrophoretic deposition (EPD) using graphite substrates under constant current density conditions. The evolution of mass per unit area with current density and deposition time was recorded. The films were characterized in the green state and after sintering at different temperatures (1300-1400) degrees C. Fully dense A-AT reaction sintered materials were obtained at low temperature by SPS, This study has been supported by the Spanish Ministry of Science and Innovation MAT2009-14369-C02-01 and MAT2009-14144-C03-02. A. Borrell, acknowledges the Spanish Ministry of Science and Innovation for her Juan de la Cierva contract (JCI-2011-10498) and the Generalitat Valenciana for the BEST/2012/302 grant and the financial support for ACOMP/2012/166.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Nanoindentation study of the mechanical and damage behaviour of suspension plasma sprayed TiO2 coatings

  • E. Rayón|||0000-0002-0653-2046
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Bonache Bezares, Victoria
  • Bannier, E.
  • Sánchez, E.
  • Denoirjean, A.
  • Ageorges, H.
TiO2 coatings can be used as self-cleaning surfaces owing to their photocatalytic and hydrophilic properties. Suspension plasma spray (SPS) has proven to be a feasible and cheap technique for producing self-cleaning surfaces with acceptable photo-activity. This paper presents a nanoindentation study of the mechanical properties (hardness. Young's modulus and scratch resistance) of photoactive layers of suspension plasma sprayed TiO2 coatings applied on to glass substrates. Microstructure observation showed that the rutile grains were surrounded by fine anatase crystals. Under the same spraying conditions, the resulting anatase/rutile concentrations varied depending on the cooling rate (the substrate being either cooled with water or in air). The results showed that higher concentrations of anatase, which is softer than rutile, reduced the scratch damage and increased the friction coefficient. (C) 2011 Elsevier B.V. All rights reserved., The study was financially supported by the Spanish Ministry of Science and Innovation (PID-600200-2009-5 and MAT2009-14144-C03-01 -02).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Microstructure and indentation mechanical properties of YSZ nanostructured coatings obtained by suspension plasma spraying

  • Carpio, P.
  • Pawlowski, L.
  • Cattini, A.
  • Bannier, E.
  • Sánchez, E.
  • E. Rayón|||0000-0002-0653-2046
  • Benavente Martínez, Rut|||0000-0002-4566-9475
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
[EN] A commercial nanosuspension of yttria-stabilised zirconia (YSZ) was successfully deposited on austenitic stainless steel substrate by suspension plasma spraying technique (SPS). A SG-100 torch with internal radial injection was used for the spraying. The pneumatic system transported the feed suspension from the containers to the plasma torch. In order to study the effect of the spraying parameters, a factorial model was used to design the experiments, changing both spraying translation speed and suspension flow rate. The coating microstructure was characterised by FEG-SEM. All coatings displayed a two-zone microstructure formed by nanometre-sized particles surrounded by fully molten areas. Moreover, crystalline phases were determined by XRD and Raman spectroscopy. Mechanical properties were also determined using nanoindentation technique. Nanoindentation tests showed a bimodal distribution of the mechanical properties (hardness and Young's modulus) which is related to the two zones (molten and partially molten) present in the coatings. (C) 2012 Elsevier B.V. All rights reserved., This work has been supported by the Spanish Ministry of Science and Innovation (project MAT2009-14144-C03) and the Research Promotion Plan of the Universitat Jaume I, action 2.1 (ref. E-2011-05) and action 3.1 (ref. PREDOC/2009/10). The authors are grateful to Leszek Łatka for his help in plasma spray experiments.