Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 17
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Local mechanical properties of graphene/polyethylene-based nanocomposites by depth-sensing indentation

  • Flores, Araceli
  • Ania, F.
  • Salavagione, Horacio J.
  • Ellis, Gary James
  • Saurel, Damien
  • Gómez-Fatou, Marián A.
Local mechanical properties of modified-graphene high-density polyethylene nanocomposites are investigated using depth-sensing indentation. Three different chemical routes are employed to boost filler dispersion by functionalizing graphene with polyethylene brushes and incorporating a small amount of free short-chain polyethylene. At large penetration depths the results reveal distinct mechanical properties for the different chemical approaches. Hardness, modulus and creep resistance are discussed in terms of filler dispersion, polymer nanostructure and plasticization of the amorphous regions by the short-chain polyethylene. By reducing the indentation size, maps of the surface mechanical properties are generated, and graphene agglomerates that appear in some nanocomposites can be clearly identified. However, these agglomerates present significantly inferior mechanical properties than those usually reported for graphene, and results at the nanoscale suggest that modification of graphene together with the viscous >liquid-like> character of the polymer host represent strong impediments for effective reinforcement. Notwithstanding, one of the nanocomposites (from the thiol-ene click reaction) overcomes these issues, achieving a macroscopic mechanical performance similar to that of the neat polymer, combined with outstanding electrical conductivity., The authors wish to thank the MINECO (Ministerio de Economía y Competitividad), Spain, for funding the research reported under Grants MAT2013-47898-C2-1-R and MAT2013-47898-C2-2-R. HJS would like to acknowledge the MICINN for a ‘Ramón y Cajal’ Senior Research Fellowship. WAXS measurements were carried out with financial support from the Comunidad de Madrid, Spain, BIPEDD-2: S2010-BMD-2457. The authors wish to thank Dr. Pilar Posadas and Mr. David Gómez of the Characterization Service of the Institute of Polymer Science & Technology, CSIC, for the AFM and SEM measurements, respectively, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Development of Advanced Elastomeric Conductive Nanocomposites by Selective Chemical Affinity of Modified Graphene

  • Salavagione, Horacio J.
  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Martínez, Gerardo
  • Ania, F.
  • Flores, Araceli
  • Gómez-Fatou, Marián A.
9 págs.; 8 figs.; 3 tabs., The preparation of conductive nanocomposites of poly(styrene-b-ethylene-co-butylene-b-styrene) (SEBS) triblock copolymers with chemically modified graphene is reported. Graphene has been functionalized with short polyethylene brushes by thiol-ene click chemistry in order to enhance the interactions of the filler with the ethylenic phase of the block copolymer. The presence of graphene modifies the morphology of the SEBS domains, reducing their size and promoting an isotropic distribution of cylinders arranged in hexagonal packing, as shown by SAXS, AFM, and TEM. The elastomeric character of SEBS persists in the nanocomposites with filler content below 1 vol %, retaining high elongation at break. In addition, the percolation threshold for electrical conductivity is found to be slightly above 0.7 vol %, reaching conductivity values of ∼10 S cm for ∼2.5 vol % of filler. These materials represent a new class of flexible conductors that open promising opportunities for applications like actuators or bodily motion sensors. Copyright © 2016 American Chemical Society, Financial support from MINECO (Ministerio de Economiá y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R and MAT2013-47898- C2-2-R is gratefully acknowledged. H.J.S. acknowledges the MINECO for a “Ramón y Cajal” Senior Research Fellowship, and P.E.-J. and S.Q.-D. acknowledge a FPI Fellowship., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Facile one-pot exfoliation and integration of 2D layered materials by dispersion in a photocurable polymer precursor

  • Gallardo Ruiz, Alberto
  • Pereyra, R.
  • Martínez-Campos, Enrique
  • García Sánchez, Carolina
  • Acitores, D.
  • Casado-Losada, I.
  • Gómez-Fatou, Marián A.
  • Reinecke, Helmut
  • Ellis, Gary James
  • Acevedo, D.
  • Rodríguez-Hernández, Juan
  • Salavagione, Horacio J.
Efficient exfoliation of graphene and related materials (GRM) and fast and inexpensive integration/assembly are crucial to fulfil their full potential. A high degree of exfoliation in organic media can be achieved with high boiling point liquids that usually leave residues after drying, which is a handicap for many applications. Here, the effective exfoliation and dispersion of GRM in a vinyl monomer, which is subsequently converted to a functional polymer by photopolymerization, is reported. Nanocomposite membranes and three-dimensional objects are produced by the photo-curing process and stereolithography 3D printing, respectively., This work was supported by MINECO (Spain, MAT2013-47898- C2-2-R, MAT2014-54231-C4-4-P, MAT2013-42957-R, MAT2016- 78437-R) and FONCYT (Argentina, PICT-2716-2013, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Control of the structure and properties of SEBS nanocomposites via chemical modification of graphene with polymer brushes

  • Enrique-Jiménez, Patricia
  • Quiles-Díaz, Susana
  • Salavagione, Horacio J.
  • Wesner, D.
  • Schönherr, H.
  • González-Casablanca, Jesús
  • García-Quismondo, Roberto
  • Martínez, Gerardo
  • Gómez-Fatou, Marián A.
  • Ania, F.
  • Flores, Araceli
Incorporation of small quantities of graphene modified with polystyrene brushes into poly (styrene-b-ethylene-co-butylene-b-styrene) (SEBS) produces elastomeric conductive nanocomposites with enhanced electromechanical behaviour. Compared to graphene modified with polyethylene rubbery brushes, polystyrene-modified graphene distorts the hexagonal packing of cylinders in SEBS to a lesser extent due to the selective interactions with the rigid polystyrene blocks. At the same time, the type of filler has an apparent impact in the nano-, macro- and electro-mechanical properties of the nanocomposites. Consistently, AFM nanoindentation shows a narrower distribution of modulus values for the polystyrene modification. Moreover, tensile testing reveals that only the nanocomposites with styrene-affine fillers show elongation at break comparable to SEBS. Most importantly, a stable electromechanical behaviour is only found for the polystyrene modification, which is attributed to the selective interaction of the brushes on graphene with the polystyrene blocks of the matrix. The work offers a comprehensive understanding of the interplay between the nature of the polymer brush grafted to graphene, the nanostructure of the nanocomposites and their final properties., The SAXS experiments were performed at BL11 beamline at ALBA Synchrotron with the collaboration of ALBA staff.Funding Fig. 11. Electromechanical tests. Resistance change as a response to cyclic strain for 2gpsSEBS (a, c) and 2gpeSEBS (b, d). P. Enrique-Jimenez et al. European Polymer Journal 97 (2017) 1–13 11 sources Financial support from MINECO (Ministerio de Economía y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R, MAT2013-47898-C2-2-R is gratefully acknowledged. PEJ and SQ also acknowledge the MINECO for a FPI Fellowship. PEJ additionally thanks the MINECO for a grant under the Predoctoral Mobility Program (EEBB-I-16-10848). This work was also supported by the European Research Council (ERC project ASMIDIAS, Grant no. 279202), the Deutsche Forschungsgemeinschaft (DFG grant no. INST 221/87-1 FUGG) and the University of Siegen., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Influence of the chemical functionalization of graphene on the properties of polypropylene-based nanocomposites

  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Papageorgiou, D. G.
  • Ania, F.
  • Flores, Araceli
  • Kinloch, I. A.
  • Gómez-Fatou, Marián A.
  • Young, R. J.
  • Salavagione, Horacio J.
9 pags., 5 figs., 4 tabs., Nanocomposites of polypropylene were prepared with different loadings of both commercially-available graphene and graphene that had been modified with low molecular weight polypropylene brushes. The dependence of the thermal stability, electrical conductivity and mechanical properties of the composites on the type and loading of graphene have been investigated. The mechanical properties were studied using several techniques, including nanoindentation, four-point bending coupled to Raman spectroscopy and tensile testing. Significant differences on the mechanical performance, due to the influence of graphene content and modification, have been observed; i.e. the Young's modulus takes values up to 30% higher for nanocomposites with modified graphene, compared to those with pristine graphene. Different trends on the variation of mechanical properties have been encountered at the local and macro scales and a discussion of the respective results from the different techniques is offered. Finally, the behavioral changes on the electrical conductivity are also discussed., Financial support by MINECO, Spain (Grants MAT2013-47898- C2-1-R and MAT2013-47898-C2-2-R) is gratefully acknowledged. S.Q.-D. and P.E.-J. acknowledge a FPI Fellowship. D.G.P, I.A.K and R.J.Y acknowledge funding from the European Union Seventh Framework Programme under grant agreement no 604391, Graphene Flagship., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Chemistry below graphene: Decoupling epitaxial graphene from metals by potential-controlled electrochemical oxidation

  • Palacio, Irene
  • Otero, Gonzalo
  • Alonso, Concepción
  • Martínez, José I.
  • López-Elvira, Elena
  • Ochando, Isabel M.
  • Salavagione, Horacio J.
  • López, María Francisca
  • García-Hernández, Mar
  • Méndez, J.
  • Ellis, Gary James
  • Martín-Gago, José A.
While high-quality defect-free epitaxial graphene can be efficiently grown on metal substrates, strong interaction with the supporting metal quenches its outstanding properties. Thus, protocols to transfer graphene to insulating substrates are obligatory, and these often severely impair graphene properties by the introduction of structural or chemical defects. Here we describe a simple and easily scalable general methodology to structurally and electronically decouple epitaxial graphene from Pt(111) and Ir(111) metal surfaces. A multi-technique characterization combined with ab-initio calculations was employed to fully explain the different steps involved in the process. It was shown that, after a controlled electrochemical oxidation process, a single-atom thick metal-hydroxide layer intercalates below graphene, decoupling it from the metal substrate. This decoupling process occurs without disrupting the morphology and electronic properties of graphene. The results suggest that suitably optimized electrochemical treatments may provide effective alternatives to current transfer protocols for graphene and other 2D materials on diverse metal surfaces., We acknowledge funding from the Spanish MINECO (Grants MAT2014-54231-C4-1-P, MAT2014-54231-C4-4-P, MAT2013- 47898-C2-2-R and MAT2017-85089-C2-1-R), the EU via the ERCSynergy Program (Grant ERC-2013-SYG-610256 NANOCOSMOS), the innovation program under grant agreement No. 696656 (GrapheneCore1- Graphene-based disruptive technologies), the Comunidad Autónoma de Madrid (CAM) MAD2D-CM Program (S2013/ MIT-3007) and computing resources from CTI-CSIC. GOI acknowledges financial support from FCT, Ministry of Science and Technology, Portugal (Grant No. PTDC/CTM-NAN/121108/2010 and IF/ 01054/2015). EL acknowledges funding from Spanish “Consolider” project CSD2010-00024. JIM acknowledges the financial support by the “Ramón y Cajal” Program of MINECO (Grant RYC-2015-17730) and NANOCOSMOS. We are grateful to Prof. C. Palacio and K. Lauwaet for their help with the XPS measurement., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Adsorption and coupling of 4-aminophenol on Pt(111) surfaces

  • Otero, Gonzalo
  • Martínez, José I.
  • Aceituno Bueno, Rebeca
  • Palomares, F. Javier
  • Salavagione, Horacio J.
  • Singh, M. K.
  • Méndez, J.
  • Ellis, Gary James
  • López, María Francisca
  • Martín-Gago, José A.
We have deposited 4-aminophenol on Pt(111) surfaces in ultra-high vacuum and studied the strength of its adsorption through a combination of STM, LEED, XPS and ab initio calculations. Although an ordered (2√3 × 2√3)R30° phase appears, we have observed that molecule–substrate interaction dominates the adsorption geometry and properties of the system. At RT the high catalytic activity of Pt induces aminophenol to lose the H atom from the hydroxyl group, and a proportion of the molecules lose the complete hydroxyl group. After annealing above 420 K, all deposited aminophenol molecules have lost the OH moiety and some hydrogen atoms from the amino groups. At this temperature, short single-molecule oligomer chains can be observed. These chains are the product of a new reaction that proceeds via the coupling of radical species that is favored by surface diffusion., We acknowledge funding from the Spanish MINECO (Grants MAT2014-54231-C4-1-P, MAT2014-54231-C4-4-P and MAT2013-47898-C2-2-R), the EU via the ERC-Synergy Program (Grant ERC-2013-SYG-610256 NANOCOSMOS), and computing resources from CTI-CSIC. MKS and GOI acknowledge financial support from FCT (Grant No. PTDC/CTM-NAN/121108/2010 and SFRH/BPD/90562/2012), Ministry of Science and Technology, Portugal. HJS would like to acknowledge the MICINN for a "Ramón y Cajal" Senior Research Fellowship, Spain. JIM acknowledges funding from both the CSIC-JAE-Doc Fellowship Program (co-funded by the European Social Fund). The research leading to these results has received funding from the European Union Seventh Framework Programme under Grant agreement No. 604391 Graphene Flagship., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Application of synchrotron infrared micro-reflectance for the study of diverse materials

  • González-Castillo, Eduin I.
  • Shuttleworth, Peter S.
  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Flores, Araceli
  • Ania, F.
  • Salavagione, Horacio J.
  • Gómez-Fatou, Marián A.
  • Yousef, Ibraheem
  • Kreuzer, Martin
  • Ellis, Gary James
Madrid from October 9-11, 2017. -- https://w3.ual.es/Congresos/AUSE/CONGRESO2017/index_congreso.html, EIGC acknowledges a PhD grant from the CONACYT (Mexico). SQD and PEJ acknowledge FPI Fellowships, and PSS a Ramón y Cajal PostDoc Fellowship, from the MINECO (Spain). MINECO also provided financial support through Grants MAT2014-54231-C4-4P, MAT2014-59674-JIN, MAT2013-47898-C2-1R and MAT2013-47898-C2-2R., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Monolithic mesoporous graphitic composites as super capacitors: From Starbons to Starenes®

  • Muñoz García, A.
  • Budarin, Vitaliy L.
  • Zhou, Y.
  • De Bruyn, Mario
  • Hunt, A. J.
  • Lari, L.
  • Lazarov, V. K.
  • Salavagione, Horacio J.
  • Morales, Enrique
  • Ellis, Gary James
  • Shuttleworth, Peter S.
In this study, we present a new class of monolithic mesoporous carbonaceous materials produced via the carbonisation of a mesoporous starch aerogel highly doped with graphite. Consecutive ball milling, microwave assisted gelation and carbonization treatment produced a high concentration of dispersed graphite. These treatments induce a strong interaction between the graphite particles and the developing carbonaceous matrix, including partial delamination of graphite and the merging of the nanoflakes into the carbonaceous structure. From a combination of SEM and TEM it was found that the graphite particles reduced in size to 24 and 37 nm, matching the pore wall sizes of the produced materials. From XRD, ball milling and heating helped reduce the number of graphene layers by 40%, with presence within the porous starch matrix reducing this a further 13%. The high degree of graphite dispersion/incorporation induces a pronounced increase in conductivity, and excellent capacitance retention, in excess of 10 000 charge-discharge cycles, offering a cost efficient and sustainably produced alternative to activated carbon based EDLCs and importantly, the resultant monolithic structures mitigate the need for additional binders., The authors would like to thank the ICTP-CSIC Characterisation Service and the personnel of the National EPSRC XPS User's Service (NEXUS) for the XPS analysis. P. S. S. gratefully acknowledges financial support from the Spanish Ministry of Economy and Competitively (MINECO) for the grants MAT2014- 59674-JIN and MAT2013-47898-C2-2-R, and for a ‘Ramón y Cajal’ Senior Research Fellowship. The Spanish Scientific Research Council, CSIC (i-LINK+0636) is also acknowledged. A. M. G. gratefully acknowledges Financial support from the Wild Fund Scholarship and an STMS grant awarded by the EUBIS COST Action, Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Searching for effective compatibilizing agents for the preparation of poly(ether ether ketone)/graphene nanocomposites with enhanced properties

  • Martínez-Gómez, Aránzazu
  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Flores, Araceli
  • Ania, F.
  • Gómez-Fatou, Marián A.
  • Salavagione, Horacio J.
The homogeneous dispersion of graphene into poly(ether ether ketone) (PEEK) remains a challenging task mostly due to the resistance of PEEK to most common organic solvents. The present investigation describes a careful selection of compatibilizing agents that allows effectively dispersing graphene into PEEK. Polyetherimide (PEI), polysulfone, (PSU), poly(1,4-phenylene ether-ether-sulfone) (PEES) and sulfonated PEEK (SPEEK) are considered as potential compatibilizers and the mechanical, thermal and electrical properties of PEEK/graphene nanocomposites with different filler contents are evaluated. Significant electrical conductivity values are obtained for the nanocomposite with SPEEK (σ > 0.01 S·cm at 4 wt% filler content) and the one incorporating PEI exhibited a percolation threshold below 2 wt%. Finally, the nanocomposites including SPEEK, PEI and PEES show a clear enhancement of the mechanical properties with increasing graphene content. Hence, nanocomposites incorporating PEI and SPEEK as compatibilizers displayed optimized electrical and mechanical properties, in addition to a thermal stability up to 550 °C., Financial support from MINECO (Ministerio de Economía y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R, MAT2013-47898-C2-2-R, MAT2017-88382-P is gratefully acknowledged. SQD and PEJ also acknowledge the MINECO for a FPI Fellowship. The authors wish to thank Mr. David Gómez (Characterization Service of the CSIC-ICTP) for the SEM measurements, Mr. J. Gonzalez-Casablanca (CAP, University Rey Juan Carlos, Spain) for TEM measurements and Dr. J.P. Fernández-Blázquez (IMDEA Materials, Spain) for assistance with hot-press preparation of nanocomposites films., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Nanoindentation mapping of multiscale composites of graphene-reinforced polypropylene and carbon fibres

  • Enrique-Jiménez, Patricia
  • Quiles-Díaz, Susana
  • Salavagione, Horacio J.
  • Fernández-Blázquez, J. P.
  • Monclús, M.A.
  • Guzmán de Villoria, R.
  • Gómez-Fatou, Marián A.
  • Ania, F.
  • Flores, Araceli
The local mechanical properties of hierarchically reinforced laminates of graphene-isotactic polypropylene (iPP) and carbon fibres are investigated by nanoindentation. Carbon fibre fabrics are alternated with films of iPP reinforced with different graphene contents and types (pristine and modified with iPP brushes). The distribution of the mechanical data obtained around one isolated carbon fibre at the boundary with the polymer layer is compared with a similar analysis far away from any fibre. In the case of neat iPP, a high E′ tail can be identified with a micrometre-sized interphase showing distinct properties from those of the polymer matrix. With increasing amount of graphene, the E′ distribution including the high E′ tail progressively shifts to higher values. It is suggested that graphene platelets accumulate at the front of the ply due to the filtering effect of the carbon fibres giving rise to a transition region, superimposed on the interphase, with enhanced properties. Nanoindentation studies reveal that the chemical modification of graphene by short-chain iPP lowers the reinforcement of the nanofiller, both near and far away from the fibres front. On the other hand, indentation push-in tests suggest that modified graphene increases the resistance of the laminate under shear stress conditions. However, from the point of view of overall performance, it lowers the electrical conductivity across the laminate. The work offers a discussion of the role of graphene type and content on the properties of the multiscale composite., Financial support from MINECO (Ministerio de Economía y Competitividad), Spain, under grants MAT2013-47898-C2-1-R, MAT2013- 47898-C2-2-R and MAT2017-88382-P is gratefully acknowledged. PEJ and SQ also acknowledge MINECO for a FPI fellowship. We are also indebted to the Department of Crystallography (IQFR, CSIC) for providing Xray diffraction facilities. Authors wish to thank Dr. Nuria García (ICTPCSIC) for profilometry measurements and Mr. David Gómez of the Characterization Service of ICTP-CSIC, for SEM studies., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Nonlinear thermal and electronic optical properties of graphene in N-methylpyrrolidone at 800 nm with femtosecond laser pulses

  • Weigand, Rosa
  • Sánchez-Balmaseda, M.
  • Afanador-Delgado, S. M.
  • Salavagione, Horacio J.
Graphene is a useful saturable absorber in a variety of lasers working in mode-locking or Q-switch regimes. The optical performance of chemically synthesized graphene is still not completely characterized. In this study, the saturable absorption and the nonlinear refractive index of graphene flakes in N-methylpyrrolidone, in both liquid and solid phases, have been studied at 800 nm with the z-scan technique using femtosecond laser pulses. The results obtained using a Ti:sapphire laser oscillator in the mode-locking regime (6 fs, 78 MHz) or in the continuous wave shows that the optical properties of graphene have a thermal origin, while at the lower repetition rate and higher energy and intensity of a Ti:sapphire amplifier (95 fs, 1 kHz), it shows the electronic Kerr effect. Solid samples with very high optical densities, equivalent to 60 layers of graphene grown by chemical vapor deposition (CVD), can be fabricated. They show a higher saturation intensity ( I s ≈ 100 GW cm) than CVD-grown (74 MW cm) or epitaxially grown (4 GW cm) graphene and intensity-dependent changes in transmission from 25% to 43%. This change in transmission in multilayer solid samples points to a good performance as a saturable absorber in laser cavities., We gratefully acknowledge the support from projects Santander-Complutense FIS2013-41709-P, MAT2013.47898- C2-2-R, and PCIN2016-021(M-ERA-NET2/0002/2016) from MINECO. Also, ICTS Centro Nacional de Microscopía Electrónica (Universidad Complutense de Madrid, Spain) for the AFM and TEM measurements., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhanced Thermal Conductivity in Polymer Nanocomposites via Covalent Functionalization of Boron Nitride Nanotubes with Short Polyethylene Chains for Heat-Transfer Applications

  • Quiles-Díaz, Susana
  • Martínez-Rubí, Y.
  • Guan, J.
  • Kim, K.S.
  • Couillard, M.
  • Salavagione, Horacio J.
  • Gómez-Fatou, Marián A.
  • Simard, B.
Boron nitride, which possesses high thermal conductivity, is often incorporated into polymer matrixes for thermal management. The enhancement in the thermal conductivity depends on the filler shape, size, effective dispersion in the matrix, and interfacial thermal resistance between the filler and matrix, and the last two are the most challenging issues. To address these challenges, in this study two different covalent functionalization approaches on boron nitride nanotubes (BNNTs) with short polyethylene (PE) chains are employed: one based on the Williamson reaction and the other on nitrene [1 + 2] chemistry. The covalent connection between the nanotubes and the polymer is confirmed by Fourier transform infrared, X-ray photoelectron microscopy, tandem thermogravimetric-infrared spectroscopy analysis and energy-filtered transmission electron microscopy. The modification of BNNTs with short polymer chains has resulted in an excellent strategy to modulate the interface in polymer composites. Tuning the interface has a strong influence on thermal transport, and up to an ∼250% increase in the thermal conductivity of BNNT-HDPE nanocomposites has been observed when the loading increases from 20 to 40 wt % of PE-modified BNNTs due to the improved dispersion and reduced interfacial thermal resistance. The materials described here show the potential for heat-transfer applications., Financial support from Spain (Grants MAT2013-47898-C2-2R and MAT2017-88382-P) and CSIC (Grant 201760I084) is gratefully acknowledged. S.Q.-D. acknowledges MINEICO for the FPI Fellowship and for a grant under the Predoctoral Mobility Program (EEBB-I-17-12247) and the hospitality of the National Research Council Canada (NRC). The authors are indebted to Malgorzata Daroszewska for the TGA and DVS measurements, to Gordon Chan for recording the SEM images of the nanotubes, to Oltion Kodra for taking the XPS measurements, to Prof. Luis Barral from University of Coruña for his help with the thermal conductivity measurements, to Prof. Rosario Benavente (ICTP-CSIC) for her help with the Cp and POM measurements, and to David Gómez of the Characterization Service of the Institute of Polymer Science & Technology for his assistance in the SEM/EDX measurements of nanocomposites. This work was partly supported by the Security Materials Technologies Program of the NRC (Grant A1-9469).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Creep behaviour of elastomeric nanocomposites by flat punch indentation: Influence of graphene modification and content

  • Ania, F.
  • Gómez-Fatou, Marián A.
  • Salavagione, Horacio J.
  • Enrique-Jiménez, Patricia
  • Quiles-Díaz, Susana
  • Flores, Araceli
Creep can be understood as the resistance of a material to a continuous stress and represents an important property for engineering design. The creep behaviour of a series of nanocomposites with electromechanical applications based on a thermoplastic elastomer, poly(styrene-b-ethylene-co-butylene-b-styrene) (SEBS), and small amounts of graphene has been explored using cylindrical flat punch depth-sensing indentation. Special attention is paid to the influence of the nature of the polymer brushes (polyethylene or polystyrene) attached to the graphene surface. Common methodologies for indentation creep analysis are critically examined and brought together to provide a comprehensive picture of creep deformation. It is found that graphene significantly reduces the creep rate and this is most significant under viscoplastic deformation than in the linear viscoelastic regime. Most interesting, polyethylene branches reduce visco-elastic-plastic flow in a more effective manner and this is attributed to the selective interaction of the filler with the matrix chains., Financial support from MINECO (Ministerio de Economía y Competitividad), Spain, under grants MAT2013-47898-C2-1-R, MAT2013- 47898-C2-2-R and MAT2017-88382-P is gratefully acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Tailored graphenic structures directly grown on titanium oxide boost the interfacial charge transfer

  • Muñoz, Roberto
  • Sánchez-Sánchez, Carlos
  • Merino, Pablo
  • López-Elvira, Elena
  • Munuera, C.
  • Gant, Patricia
  • López, María Francisca
  • Castellanos-Gómez, Andrés
  • Martín-Gago, José A.
  • García-Hernández, Mar
10 pags., 8 figs., 1 tab., The successful application of titanium oxide-graphene hybrids in the fields of photocatalysis, photovoltaics and photodetection strongly depends on the interfacial contact between both materials. The need to provide a good coupling between the enabling conductor and the photoactive phase prompted us to directly grow conducting graphenic structures on TiO crystals. We here report on the direct synthesis of tailored graphenic structures by using Plasma Assisted Chemical Vapour Deposition that present a clean junction with the prototypical titanium oxide (1 1 0) surface. Chemical analysis of the interface indicates chemical bonding between both materials. Photocurrent measurements under UV light illumination manifest that the charge transfer across the interface is efficient. Moreover, the influence of the synthesis atmosphere, gas precursor (CH) and diluents (Ar, O), on the interface and on the structure of the as-grown graphenic material is assessed. The inclusion of O promotes vertical growth of partially oxidized carbon nanodots/rods with controllable height and density. The deposition with Ar results in continuous graphenic films with low resistivity (ρ = 6.8 · 10 Ω·m). The synthesis protocols developed here are suitable to produce tailored carbon-semiconductor structures on a variety of practical substrates as thin films, pillars or nanoparticles., We acknowledge funding from the Spanish MINECO (Grants MAT2014-54231-C4-1-P, MAT2013-47898-C2-2-R and MAT2017-85089-C2-1-R), the EU via the ERC-Synergy Program (Grant ERC-2013-SYG-610256 NANOCOSMOS), the innovation program under grant agreement No. 696656 (Graphene Core1-Graphene-based disruptive technologies) and grant agreement No. 785219 (Graphene Core2-Graphene-based disruptive technologies) and the Comunidad Autónoma de Madrid (CAM) MAD2D-CM Program (S2013/MIT-3007and P2018/NMT-4367). C.S.S. acknowledges Juan de la Cierva program (IJCI-2014-19291). A.C.-G. acknowledges to grant agreement n°755655, ECR-StG 2017 project 2D-TOPSENSE.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Development of Multifunctional PEEK Nanocomposites based on Graphene

  • Quiles-Díaz, Susana
  • Enrique-Jiménez, Patricia
  • Flores, Araceli
  • Ania, F.
  • Gómez-Fatou, Marián A.
  • Salavagione, Horacio J.
  • Martínez-Gómez, Aránzazu
ECCM18 - 18th European Conference on Composite Materials, Athens, Greece, 24-28th June 2018 . -- 7 pags., 2 figs., 1 tab., In this communication we present the preparation of multifunctional Polyether ether ketone (PEEK) nanocomposites with graphene. PEEK is an important high-perfomance semicrystalline thermoplastic matrix that displays a unique combination of toughness, stiffness, chemical and solvent resistance, retention of physical properties at high temperatures and recyclability. A relevant step forward to expand its field of application is the incorporation of electrical conductivity, developing multifunctional materials. Therefore, graphene has been incorporated into the matrix aiming to achieve electrical conductivity without a significant detriment on PEEK properties. The accomplishment of an effective transfer of the properties from graphene to the matrix is controlled by the nanofiller dispersion within the matrix and the presence of a strong polymer/graphene interface. One of the most efficient strategies to improve both parameters consists on the covalent modification of graphene with short polymer chains and their subsequent use as filler in the cognate polymer matrix1-3. Nevertheless, this approach is unachievable in our case since PEEK is insoluble in organic solvents. An alternative strategy, proven to be effective to increase carbon nanotubes dispersion within PEEK matrix4-5, consists on nanofiller wrapping in compatibilizing polymers. In this study we prepared PEEK/graphene nanocomposites using compatibilizers like polyetherimide (PEI), poly(1-4-phenylene ether-ether sulfone) (PEES), polysulfone (PSU) and sulfonated PEEK (SPEEK), which are amorphous thermoplastic polymers miscible with and structurally similar to PEEK. Composites incorporating compatibilizer/graphene nanofillers display a slight decrease on the thermal stability with respect to PEEK, which is related to the intrinsic thermal stability of the compatibilizer employed. Regarding the electrical conductivity, significant conductivity values were measured depending on both nanofiller concentration and the nature of the compatibilizer. A slight enhancement was observed on the mechanical properties of the nanocomposites for some of the non-covalent functionalized graphene. The morphology, thermal behavior and mechanical performance of all nanocomposites will be compared and the best strategy leading to a balance among electrical, thermal and mechanical properties will be shown., Financial support from MINEICO (Ministerio de Economía, Industria y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R and MAT2013-47898-C2-2-R is gratefully acknowledged. SQD and PEJ also acknowledge the MINECO for a FPI Fellowship.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Nanoindentation of Graphene-Reinforced Polypropylene Nanocomposites Laminated with Carbon Fibres

  • Enrique-Jiménez, Patricia
  • Quiles-Díaz, Susana
  • Salavagione, Horacio J.
  • Gómez-Fatou, Marián A.
  • Ania, F.
  • Flores, Araceli
ECCM18 - 18th European Conference on Composite Materials, Athens, Greece, 24-28th June 2018 . -- 7 pags., 6 figs., The mechanical properties of graphene-reinforced polypropylene nanocomposites laminated with alternating carbon fibre mats have been studied at a local scale by nanoindentation and results are correlated with morphological studies by means of scanning electron microscopy (SEM). Mechanical maps (storage modulus and hardness) have been obtained using indentation depths of a few tens of nanometres. Analysis of the distribution of E´ values close to and far away from isolated carbon fibres offers a comprehensive understanding of the role of graphene on the mechanical properties of the transition region between the reinforced matrix and the microsized fibres., Financial support from MINECO (Ministerio de Economía y Competitividad), Spain, for funding the research reported under grants MAT2013-47898-C2-1-R, MAT2013-47898-C2-2-R is gratefully acknowledged. PEJ and SQ also acknowledge the MINECO for a FPI Fellowship. The authors wish to thank Mr. David Gómez of the Characterization Service of the Institute of Polymer Science & Technology, CSIC, for the SEM measurements.