Skip to main content

GENERACION Y APLICACION DE UN MATERIAL NANOCOMPUESTO DE VIDRIO BIOACTIVO Y AG MEDIANTE LA TECNICA DE ABLACION LASER EN CONDICIONES AMBIENTE DE FORMA CONTROLADA

MAT2015-71459-C2-2-P

•
Funding agency name Ministerio de Economía y Competitividad
Funding agency acronym MINECO
Program Programa Estatal de Fomento de la Investigación Científica y Técnica de Excelencia
Subprogram Subprograma Estatal de Generación de Conocimiento
Call Proyectos de I+D (Excelencia / Generación de Conocimiento)
Call year 2015
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Management unit Secretaría de Estado de Educación, Formación Profesional y Universidades
Beneficiary centre UNIVERSIDAD DE VIGO

Resultados relacionados

Resultados totales (Incluyendo duplicados): 2
Encontrada(s) 1 página(s)

Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

RE-irradiation of silver nanoparticles obtained by laser ablation in water and assessment of their antibacterial effect

  • Fernández Arias, Mónica
  • Boutinguiza Larosi, Mohamed
  • Del Val Garcia, Jesús
  • Medina, E
  • Muñoz Rodríguez, Daniel
  • Riveiro Rodríguez, Antonio
  • Comesaña Piñeiro, Rafael
  • Lusquiños Rodríguez, Fernando
  • Gil, F. J
  • Pou Saracho, Juan María
The rapid evolution of resistant bacteria is a huge problem in medicine because makes the treatment of infections more and more difficult. The bactericidal properties of noble metal nanoparticles could be a solution. In this work silver nanoparticles were produced by using two nanosecond Nd:YVO 4 lasers operating at 1064 and 532 nm respectively to ablate a silver target submerged in pure de-ionized water. Part of the resulting colloidal solution was injected as a fine stream by a compressed air system and re-irradiated one and three times with the same laser to resize and get uniform nanoparticles. The obtained nanoparticles by ablation and re-irradiation consisted of crystalline Ag nanoparticles with a bimodal size distribution. The particle size has been reduced by subsequent laser re-irradiation with both laser sources, reaching a 40% of mean size reduction. Inhibitory effects on the proliferation of Staphylococcus aureus was demonstrated on silver nanoparticles obtained after re-irradiation with the infrared laser., Xunta de Galicia | Ref. ED481D 2017/010, Xunta de Galicia | Ref. ED481B 2016/047-0, Xunta de Galicia | Ref. ED431B 2016/042, Ministerio de Economía y Competitividad | Ref. MAT2015-71459-C2-2-P, Ministerio de Economía y Competitividad | Ref. MAT2015-71459-C2-1-P, Ministerio de Educación, Cultura y Deporte | Ref. PRX17/00157
Investigo. Repositorio Institucional de la Universidade de Vigo
Publication Artículo científico (JournalArticle)

Laser direct writing of Co-superalloy lines for micro-fabrication applications

  • Del Val Garcia, Jesús
  • Comesaña Piñeiro, Rafael
  • Riveiro Rodríguez, Antonio
  • Lusquiños Rodríguez, Fernando
  • Quintero Martínez, Félix
  • Boutinguiza Larosi, Mohamed
  • Pou Saracho, Juan María
Co-superalloy lines were deposited on stainless steel by a direct laser writing technique: laser micro-cladding by lateral powder injection. With the aim of producing small strips as thin and narrow as possible, the mean size of the powder used was 8 μm. Using such fine particles makes conventional powder feeders useless, due to the formation of agglomerates unable to be feed. Therefore a new powder feeder, here described, was designed, constructed and tested. A processing parameters map was established, identifying the working window for laser micro-cladding. The new power feeder and a high brightness, good beam quality fiber laser allowed producing fine lines just 14 μm wide and 7.2 μm thick. Microstructure and mechanical properties, in terms of Hardness and Elastic Modulus, were evaluated confirming that the fine strips maintain the main characteristics of the hardfacing alloy. Potential applications include micro-part fabrication and repairing such as micro-moulds, and production of 3D parts at sub-millimetre scales., Xunta de Galicia | Ref. ED431B 2016/042, Xunta de Galicia | Ref. ED481D 2017/010, Xunta de Galicia | Ref. ED481B 2016/047-0, European Comission | Ref. EAPA_151/2016 Interreg Atlantic Area, Ministerio de Economía y Competitividad | Ref. MAT2015-71459-C2-1-P