Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 31
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Selective thermal emission of directionally solidified Al2O3/Y3-xErxAl5O12 eutectics: Influence of the microstructure, temperature and erbium content

  • Oliete, Patricia B.
  • Orera, Alodia
  • Sanjuán, M. L.
  • Merino, R. I.
Directionally solidified eutectic rods of Al2O3-Y3−xErxAl5O12 (0 ≤ x ≤ 3) composition have been grown using the laser floating zone method at processing rates of 25 mm/h and 750 mm/h. For all the samples the microstructure presents the same morphology, consisting of an interpenetrated 3D eutectic network of both Al2O3 and garnet phases, while eutectic interspacing strongly depends on the solidification rate. Optical absorption, luminescence and thermal emission have been investigated as a function of the growth rate and the erbium content. From the luminescence characterization it can be concluded that erbium ions are present in the eutectic only in the garnet phase. Near infrared thermal emission has been measured at temperatures ranging from 1000 to 1500 °C. Selective emission consisting of an emission band at 1540 nm and a weaker line at 970 nm, ascribed to the radiative de-excitation of the thermally excited Er3+ ions from the 4I13/2 and 4I11/2 multiplets to the 4I15/2 ground state respectively, has been detected in all the samples containing erbium. The influence of the erbium content, the microstructure and the temperature on the thermal emission has been investigated. The strongest selective emission has been obtained for samples with x=3 although it does not increase proportionally to the erbium content. The thermal emission becomes more intense when the temperature is increased but the selective emission seems to saturate at temperatures higher than 1300 °C. This effect is especially noticeable for x=3 and is attributed to thermally activated non-radiative de-excitation channels. It is suggested that these channels become effective through energy transfer among Er3+ ions and towards killers., The authors gratefully acknowledge the financial support from the Ministerio de Economía y Competitividad de España under projects MAT2013-41045-R and MAT2016-77769-R., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Influence of microstructural size on the thermal shock behavior of Al2O3-Er3Al5O12 directionally solidified eutectics

  • Nie, Ying
  • Oliete, Patricia B.
  • Merino, R. I.
We analyze the thermal shock resistance of directionally solidified eutectics. When quenching in water, the resistance starts to deteriorate with temperature differences in the range 260 to 300 K, almost independent of the microstructure size (or initial flexural strength). Unlike other strong, dense ceramics, the loss of strength is gradual upon quenching in boiling water. The onset of crack propagation seems to be controlled by the mismatch of the thermal and elastic properties of the component phases, while the length of the propagated cracks is limited by their quantity, which is estimated to scale approximately with the interface density., This work has been supported by the Spanish Ministerio de Economía, Industria y Competitividad (MINECO) and the CE (FEDER Funds) [grants number MAT2013-41045-R-EMITEME and MAT-2016-77769R-FLASCERAMAT]. Authors would like to acknowledge the Servicio General de Apoyo a la Investigación-SAI, Universidad de Zaragoza. Y. Nie would like to acknowledge the China Scholarship Council for a funding of Doctoral Joint-Training Program., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Directionally solidified Ni doped MgO-MgSZ eutectic composites for thermophotovoltaic devices

  • Sola, D.
  • Oliete, Patricia B.
  • Merino, R. I.
  • Peña, J. I.
Ni-doped MgO-MgSZ eutectic composites were investigated as selective emitters for thermophotovoltaic devices. MgO-MgSZ:Ni eutectic rods were directionally solidified at 25 and 500 mm/h using the laser floating zone technique. Microstructure was strongly dependent on the growth rate, the size of the eutectic phases decreased as the growth rate increased. A hardness of ∼11 GPa and a fracture toughness of ∼1.6 MPa were obtained from indentation techniques, not showing dependence on the growth rate. Flexure strength increased from ∼400 MPa in samples grown at 25 mm/h up to ∼1 GPa for those solidified at 500 mm/h, which was attributed to the decrease of the phase size. Thermal emission of eutectic composites was studied up to 1400 °C. An intense broad emission band centred in 1.5 μm matching with the sensitive region of the GaSb photoconverter was found. The selective emission was ascribed to the de-excitation of the thermally excited Ni2+ ions., This work has been supported by the Spanish Ministerio de Economía Industria y Competitividad (MINECO) and the CE (FEDER Funds) [grants number MAT2013-41045-R-EMITEME and MAT-2016-77769R-FLASCERAMAT]. D. Sola thanks the PIT2 programme of the University of Murcia for the financial support of his contract., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Understanding the complex structural features and phase changes in Na2Mg2(SO4)3: A combined single crystal and variable temperature powder diffraction and Raman spectroscopy study

  • Trussov. I. A.
  • Male, L. L.
  • Sanjuán, M. L.
  • Orera, Alodia
  • Slater, P. R.
Sodium mixed metal sulphates have attracted considerable attention, both in terms of mineralogy and more recently due to interest in Na ion containing materials for battery applications. The phase, Na2Mg2(SO4)3, has been previously reported to undergo a phase change to langbeinite at high temperatures, which is interesting given that usually the langbeinite structure is only adopted when large alkali metal ions, e.g. K, Cs, are present. Nevertheless the room temperature structure of this phase has remained elusive, and so in this work, we report a detailed structural study of this system. We show that room temperature Na2Mg2(SO4)3 can only be prepared by quenching from high temperature, with slow cooling leading to phase separation to give the previously unreported systems, Na2Mg(SO4)2 and Na2Mg3(SO4)4. We report the structures of quenched Na2Mg2(SO4)3 (monoclinic, ), as well as Na2Mg(SO4)2 (triclinic, ̅) and Na2Mg3(SO4)4 (orthorhombic, , detailing their complex structural features. Furthermore, we report a study of the thermal evolution of quenched Na2Mg2(SO4)3 with temperature through variable temperature XRD and Raman studies, which shows a complex series of phase transitions, highlighting why this phase has proven so elusive to characterise previously, and illustrating the need for detailed characterisation of such sulphate systems., We would like to thank the Bolashak International Scholarship Fund, Kazakhstan (PhD scholarship for Ivan Trussov) for funding. The work has been supported by the Spanish Ministerio Economía y Competitividad and Feder funds through grant MAT2016-77769R as well., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Synthesis and structures of sodium containing K2-xNaxMg2(SO4)3 langbeinite phases

  • Trussov. I. A.
  • Driscoll, L.L.
  • Male, L. L.
  • Sanjuán, M. L.
  • Orera, Alodia
  • Slater, P. R.
In this work we report a detailed structural study of the K2-xNaxMg2(SO4)3 series in order to evaluate the effect of Na incorporation on the structure. The results show that the cubic langbeinite structure is observed at room temperature for high Na levels; K2-xNaxMg2(SO4)3 (0 ≤ x ≤ 1.8). Increasing the Na content further, 1.8 < x ≤ 1.9, leads to significant structural distortions, with the observation of an enlarged orthorhombic cell. These latter systems resemble a highly distorted variant of the langbeinite structure, and this relationship is also illustrated by the fact that they transform to the cubic langbeinite structure at relatively low temperature (≈200 °C). In conjunction with our prior studies on Na2Mg2(SO4)3 (complex monoclinic cell, which also transforms to langbeinite at elevated temperature), this work highlights the flexibility of the langbeinite structure to accommodate high levels of Na ions, thus offering another potential avenue to manipulate the properties of materials with this structure-type., We would like to thank the Bolashak International Scholarship fund (PhD scholarship for Ivan Trussov) for funding. The work has been supported by the Spanish Ministerio Economía y Competitividad and Feder funds through grant MAT2016-77769R as well., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Non-Hall-Petch hardness dependence in ultrafine fibrous MgAl2O4-MgO eutectic ceramics fabricated by the laser-heated floating zone (LFZ) method

  • Moshtaghioun, Bibi Malmal
  • Peña, J. I.
MgAl2O4-MgO eutectic ceramics were fabricated by the laser-heated floating zone (LFZ) method with various growth rates to assess its possible beneficial effect on microstructural aspects and mechanical properties. It was determined that the growth rate optimizing the microstructure and mechanical properties is 750 mm/h; below this value, coarsening of the fibrous microstructure takes place with a degradation of these properties. In the extreme case of 50 mm/h growth rate, the presence of undesirable transverse cracks was unavoidable. Thanks to the high growth rate of 750 mm/h, ultra-fine fibrous microstructure MgAl2O4-MgO eutectic ceramics can thus be fabricated with greater hardness (15.5 GPa from Vickers indentation and 22 GPa from nanoindentation) and flexural strength (˜345 MPa). It is reported that hardness scales with the interfiber spacing λ according to a law of the type lnλ/λ, contrary to the assumed Hall-Petch-like dependence. This proposed law can be explained in terms of dislocation hardening induced by the MgO fibers., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants No. MAT2016-77769-R BMM wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Does grain size have an influence on intrinsic mechanical properties and conduction mechanism of near fully-dense boron carbide ceramics?

  • Moshtaghioun, Bibi Malmal
  • Laguna-Bercero, M. A.
  • Gómez-García, Diego
  • Peña, J. I.
This work is concentrated on getting a reply to the following question: how does the grain size of boron carbide specimens influence on their mechanical and electrical response? It is a common issue that both essential properties are usually affected by the grain boundaries. To this purpose, a set of near fully-dense boron carbide specimens were prepared by spark plasma sintering. In order to reduce residual porosity and grain-size effects, nanoindentation tests at room temperature were conducted. DC conductivity was measured through four-point test technique from room temperature up to 800 °C. The results show that hardness can reach values as high as ∼60 GPa and plasticity onset takes place at around 23 GPa by dislocation nucleation. Regarding the conductivity, it is found that grain boundaries can block the mobility of bipolarons in an effective way. A simple additive law is provided to account for the resistivity of boron carbide polycrystals., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants No. MAT2015- 71411-R. and MAT2016-77769-R wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Elusive super-hard B6C accessible through the laser-foating zone method

  • Moshtaghioun, Bibi Malmal
  • Cumbrera, F. L.
  • Gómez-García, Diego
  • Peña, J. I.
Boron carbide is among the most promising ceramic materials nowadays: their mechanical properties are outstanding, and they open potential critical applications in near future. Since sinterability is the most critical drawback to this goal, innovative and competitive sintering procedures are attractive research topics in the science and technology of this carbide. This work reports the pioneer use of the laser-floating zone technique with this carbide. Crystallographic, microstructural and mechanical characterization of the so-prepared samples is carefully analysed. One unexpected output is the fabrication of a B6C composite when critical conditions of growth rate are adopted. Since this is one of the hardest materials in Nature and it is achievable only under extremely high pressures and temperatures in hot-pressing, the use of this technique offers a promising alternative for the fabrication. Hardness and elastic modulus of this material reached to 52 GPa and 600 GPa respectively, which is close to theoretical predictions reported in literature., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants Nos MAT2015-71411-R and MAT2016-77769-R. B.M.M. wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Medium infrared transparency of MgO-MgAl2O4 directionally solidified eutectics

  • Moshtaghioun, Bibi Malmal
  • Peña, J. I.
  • Merino, R. I.
MgAl2O4-MgO eutectic ceramics have been fabricated by the laser floating zone method. Increasing growth rates from 10 to 50 mm/h, the microstructure transformed from irregular MgO rod-to-lamellae phase and it approached to almost homogeneous rod morphology. At the highest used velocity of 750 mm/h, the cell structure was completely dominant and the samples were free from transversal cracks. Although the highest flexure strength was found at 750 mm/h growth rate, the maximum optical transmittance in the medium-infrared range was obtained for 50 mm/h growth rate and for 1 mm thick samples reached values higher than 75% in the wavelengths between 4 and 5.3 μm. The enhanced transmittance for the sample with 50 mm/h growth rate can be explained in terms of the close refraction indexes of the component phases and the characteristic lengths of the resulting microstructure showing fully dense ceramics with the finest and almost homogeneous microstructure., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants No. MAT2016-77769-R, and Gobierno de Aragon (Grupo Reconocido DGA T02_17R) and the associated EU Regional Development Funds. BMM wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Spectroscopic insight into the interplay between structural disorder and oxidation degree in melt‐grown Ce0.5Zr0.5O2‐y compounds

  • Oliete, Patricia B.
  • Orera, Alodia
  • Sanjuán, M. L.
The oxygen storage capacity of CexZr1‐xO2‐y compounds arises from the mixed‐valent character of cerium, which makes the system sensitive to external factors such as temperature and oxygen partial pressure through their influence in the Ce valence, cation ordering and oxygen content. In this work, we analyze the phase relations in Ce0.5Zr0.5O2‐y compounds fabricated by the laser floating zone technique in either oxidising or reducing atmosphere. Chemical, structural, and microstructural properties are studied by X‐ray diffraction, thermogravimetry, scanning electron microscopy (energy dispersive X‐ray spectroscopy and electron backscatter diffraction), and Raman spectroscopy. The latter proves to be determinant to discriminate between phases arising from subtle variations of atomic distribution that are hardly distinguished by X‐ray diffraction or energy dispersive X‐ray analyses. Cation disordered, fluorite‐like phases are obtained when processing is performed in air, whereas cation‐ordered, pyrochlore‐related phases are formed when processing in Ar+5%H2 atmosphere. Processing in a low but non‐negligible pO2 yields, besides the pyrochlore and fluorite‐like phases, an intermediate state with partial disorder that may be relevant for catalysis applications. The vibrational Raman spectrum of the Ce2Zr2O7 pyrochlore has been fully interpreted through polarisation measurements at room and low temperature. Bands arising from crystal field transitions within the ground and first excited multiplets of Ce3+ ions are also identified. The electronic Raman spectrum is found to be a sensitive probe of the degree of cation and oxygen order in these compounds., The authors acknowledge the financial support from the Spanish Ministerio de Economía y Competitividad and Feder Funds under project MAT2016‐77769‐R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Selective emitters for thermophotovoltaics based on eutectic composites

  • Merino, R. I.
  • Oliete, Patricia B.
Resumen del trabajo presentado a la 6th Directionally Solidified Eutectics Conference (DSEC VI) celebrada en Salerno Italia) del 10 al 14 de septiembre de 2019., This work has been supported by the Spanish Ministerio de Economía, Industria y Competitividad (MINECO) and the CE (FEDER Funds) [grant number MAT-2016-77769R-FLASCERAMAT], and by the Departamento de Innovación, Investigación y Universidad de la DGA [grant number T02-17R].]
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Measuring membrane permeation rates through the optical visualization of a single pore

  • Tsochataridou, Sotiria
  • Mutch, Greg A.
  • Neagu, Dragos
  • Papaioannou, Evangelos I.
  • Sanjuán, M. L.
  • Ray, Brian
  • Merino, R. I.
  • Orera, V. M.
  • Metcalfe, S.
Membranes are a critical technology for energy-efficient separation processes. The routine method of evaluating membrane performance is a permeation measurement. However, such measurements can be limited in terms of their utility: membrane microstructure is often poorly characterized; membranes or sealants leak; and conditions in the gas phase are poorly controlled and frequently far-removed from the conditions employed in the majority of real processes. Here, we demonstrate a new integrated approach to determine permeation rates, using two novel supported molten-salt membrane geometries. In both cases, the membranes comprise a solid support with laser-drilled pores, which are infiltrated with a highly CO2-selective molten carbonate salt. First, we fabricate an optically transparent single-crystal, single-pore model membrane by local laser drilling. By infiltrating the single pore with molten carbonate, monitoring the gas–liquid interface optically, and using image analysis on gas bubbles within the molten carbonate (because they change volume upon controlled changes in gas composition), we extract CO2 permeation rates with exceptional speed and precision. Additionally, in this arrangement, microstructural characterization is more straightforward and a sealant is not required, eliminating a major source of leakage. Furthermore, we demonstrate that the technique can be used to probe a previously unexplored driving force region, too low to access with conventional methods. Subsequently, we fabricate a leak-free tubular-supported molten-salt membrane with 1000 laser-drilled pores (infiltrated with molten carbonate) and employ a CO2-containing sweep gas to obtain permeation rates in a system that can be described with unprecedented precision. Together, the two approaches provide new ways to measure permeation rates with increased speed and at previously inaccesible conditions., The research leading to these results has received funding from the European Research Council (ERC) under the European Union’s Seventh Framework Programme (FP/2007-2013)/ERC Grant Agreement 320725 and the Engineering and Physical Sciences Research Council (EPSRC) via Grants EP/M01486X/1, EP/P007767/1, and EP/P009050/1. Greg A. Mutch thanks the EPSRC for his Doctoral Prize Fellowship (EP/M50791X/1) and Newcastle University for a Newcastle University Academic Track (NUAcT) Fellowship. Financial support from the Spanish Ministerio de Economía y Competitividad and FEDER Funds under Project MAT2016-77769-R is acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Mg2SiO4-MgAl2O4 directionally solidified eutectics: Hardness dependence modelled through an array of screw dislocations

  • Moshtaghioun, Bibi Malmal
  • Gómez-García, Diego
  • Peña, J. I.
Mg2SiO4-MgAl2O4 eutectic ceramics have been fabricated by means of the laser floating zone (LFZ) technique. The microstructure has revealed as an unusual one at lower growth rate, composed of broken lamellae of MgAl2O4 distributed randomly along one matrix, composed of Mg2SiO4. At higher growth rates, a cell structure with intra-cell lamella structure is dominant. Contrary to most eutectic systems, hardness is not dependent upon the inter-spacing, but it does depend on one characteristic length of lamellae: their perimeter. One simple model based upon the dislocation is proposed, which successfully accounts for such extraordinary hardness law. Accordingly, Mg2SiO4-MgAl2O4 eutectic ceramics fabricated at 50 mm/h growth rate with the smallest MgAl2O4 lamella perimeter favorably showed more elevated hardness (13.4 GPa from Vickers indentation and 15.3 GPa from nanoindentation) and strength (∼430 MPa) than those found in the monolithic Mg2SiO4 matrix., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants No. MAT2016-77769-R and MAT2015- 71411-R and Gobierno de Aragon (Grupo Reconocido DGA T02_17R) and the associated EU Regional Development Funds. BMM wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza and the ‘Junta de Andalucía’ project P18-RTJ-1972., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

High CO2 permeability in supported molten-salt membranes with highly dense and aligned pores produced by directional solidification

  • Grima, Lorena
  • Mutch, Greg A.
  • Oliete, Patricia B.
  • Bucheli, Wilmer
  • Merino, R. I.
  • Papaioannou, Evangelos I.
  • Bailey, Josh J.
  • Kok, M. D.
  • Brett, D. J. L.
  • Shearing, P. R.
  • Metcalfe, Ian S.
  • Sanjuán, M. L.
Composite molten salt-ceramic membranes are promising devices for high-temperature CO2 separation. Intensive material properties impact on separation performance as do membrane geometry (thickness) and microstructure (pore volume fraction, size, connectivity, and tortuosity factor). Although controlling pore size is considered somewhat routine, achieving pore alignment and connectivity is still challenging. Here we report the production of the first gas separation membrane using a porous ceramic matrix obtained from a directionally-solidified magnesium-stabilised zirconia (MgSZ) – MgO fibrilar eutectic as the membrane support. MgO was removed from the parent material by acid-etching to create a porous matrix with highly aligned pores with diameters of ~1 μm. X-ray nano-computed tomography of a central portion (~32,000 μm3) of the support identified ~21% porosity, with all pores aligned within 10° and ~76% percolating along the longest sampled length. Employing the matrix as a support for a carbonate molten salt, a high CO2 permeability of 1.41x10-10 mol.m-1.s-1.Pa-1 at 815 °C was achieved, among the highest reported for supported molten-carbonate membranes (typically 10-12 to 10-10 mol.m-1.s-1.Pa-1 at similar temperatures). We suggest that the high permeability is attributable to the excellent pore characteristics resulting from directional solidification, namely a dense array of parallel, micron-scale pores connecting the feed and permeate sides of the membrane., The authors acknowledge the financial support from the Spanish Ministerio de Economía y Competitividad and Feder Funds under project MAT2016-77769R. L. Grima acknowledges financial support through grant BES-2017-079683 associated to the aforementioned project. The research leading to these results has received funding from the European Research Council under the European Union's Seventh Framework Programme (FP/2007-2013)/ERC Grant Agreement Number 320725 and from the Engineering & Physical Sciences Research Council (EPSRC) via grants EP/M01486X/1, EP/P007767/1 and EP/P009050/1. PRS acknowledges the Royal Academy of Engineering (CiET1718/59). PRS, DJLB, JJB and MDK acknowledge the support of The Faraday Institution (faraday.ac.uk; EP/ S003053/1). G. Mutch was supported by the Royal Academy of Engineering under the Research Fellowship Scheme and would like to thank the EPSRC for his Doctoral Prize Fellowship (EP/M50791X/1) and Newcastle University for a Newcastle University Academic Track (NUAcT) Fellowship. X-Ray CT acquisition and analysis was supported by UCL and EPSRC under EP/N032888/1. We thank the Servicio General de Apoyo a la Investigación-SAI (Universidad de Zaragoza) for technical support in X-ray diffraction and electron microscopy experiments, Rubén Gotor for technical assistance in sample preparation and R. Lahoz for laser-drilling the YSZ plate that serves as the membrane base., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Can Y2O3-MgO eutectics be new promising structural and optical ceramics?

  • Moshtaghioun, Bibi Malmal
  • Peña, J. I.
  • Merino, R. I.
Hasta el 28 de agosto de 2021 puede accederse gratis a la versión publicada del artículo en este enlace: authors.elsevier.com/c/1dNyu_UwYsE~Gd, The manuscript addresses the solidification of Y2O3-MgO eutectic composites for the first time, and the study of their microstructure, mechanical properties and infrared transmittance. The composites with eutectic composition (20 % vol MgO) have been solidified using the laser floating zone method, at solidification rates between 25 mm/h and 750 mm/h. Their microstructure has been quantified and the conditions for coupled or cellular regime determined. They are dense, with elastic modulus, as determined from nanoindentation tests of around 200 GPa. The highest 3-point flexural strength (256±25 MPa) values and highest infrared optical transmittance has been observed for the material solidified with the finest, still homogeneous microstructure that could be achieved. This microstructure, which is achieved at a solidification rate of 50mm/h, consists of MgO fibers of 600 nm diameter embedded in the Y2O3 matrix. The thin MgO rods and the associated residual stress field contribute to the material strength as they deviate the propagating crack. The Vickers Hardness ranged from 9.5 to 11.5 GPa, with mild increase with the decrease of the microstructural size which has been rationalized as the MgO rods blocking the movement of dislocations in the matrix, as in other studied composites. Indentation fracture toughness values around 3 MPa.m1/2, independent of the sample microstructure, have been measured. In the longitudinal direction transmittance values higher than 80 % in the wavelength range from 3.5 to 7 μm, for 1 mm thick slices have been measured. Light scattering limits the short wavelength cut-off to around 2 μm for light travelling in the longitudinal direction, while a transmittance gap is observed in the transverse direction, of photonic crystal like nature., This work was supported by the Ministerio de Economía y Competitividad (Government of Spain) and FEDER Funds under Grants No. MAT77769-R and Gobierno de Aragón, Subvención a Grupos de Investigación No. T02_20R. BMM wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva-Incorporación” fellowship during her sabbatical stay in Zaragoza and is grateful to the Ministerio de Economía y Competitividad for the research funding through the project PID2019-103847RJ-I00 and ‘Junta de Andalucía’ through the project P18-RTJ-1972. We want to thank Rubén Gotor for his help in several tasks of material preparation. Authors would like to acknowledge also the use of the Servicio General de Apoyo a la Investigación SAI, Universidad de Zaragoza, namely, the Service of Electron Microscopy of Materials and the Service of X-ray Diffraction and Fluorescence Analysis., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Cation-driven electrical conductivity in Ta-doped orthorhombic zirconia ceramics

  • Moshtaghioun, Bibi Malmal
  • Laguna-Bercero, M. A.
  • Peña, J. I.
  • Gómez-García, Diego
  • Domínguez-Rodríguez, Arturo
This paper is devoted to the study of the electrical conductivity of tantalum-doped zirconia ceramics prepared by spark plasma sintering. In this study, the temperature dependence of conductivity in as-prepared specimens and in those previously annealed in air is determined and compared. A semi-empirical model, which is based on the oxidation states of the cations, has been developed and successfully assessed. According to this, the conductivity is basically controlled by the diffusion of tetravalent zirconium cations in both cases, although the concentration of these species varies drastically with the amount of induced oxygen vacancies. This is a quite unexpected fact, since conductivity is normally controlled by anionic diffusion in zirconia ceramics. This option is forbidden here due to the presence of substitutional pentavalent cations. Therefore, conductivity values are much lower than those reported in trivalent or divalent substitutional cation doped zirconia ceramics., The authors would like to acknowledge provided by several institutions: BMM wants to acknowledge the Spanish Ministry of Science and Innovation through the grant PID2019-103847RJ-I00, as well as the financial support awarded by the Regional government of the ‘Junta de Andalucía’ through the project P18-RTJ-1972. BMM and JIP gratefully acknowledge the financial support provided the Ministry of Science in Spain through the projects MAT2016-77769-R and Gobierno de Aragón, Spain (Grupo Reconocido DGA T02_17R) and the associated EU Regional Development Funds. MLB acknowledges the funding support provided by the projects MAT2015-68078-R and PID2019-107106RB-C32 funded by the Spanish Ministry of Science and Innovation. Finally, DGG and ADR are grateful to the Spanish Ministry of Science for the research funding through the project MAT2015-71411-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Pyrochlore-like ZrO2-PrOx compounds: The role of the processing atmosphere in the stoichiometry, microstructure and oxidation state

  • Grima, Lorena
  • Peña, J. I.
  • Sanjuán, M. L.
The object of this work is to study the relation between composition, microstructure and oxidation state of Pr2±xZr2∓xO7±y materials produced by the laser–floating zone (LFZ) technique. Three compositions are studied, nominally Pr1.7Zr2.3O7+y, Pr2Zr2O7+y and Pr2.24Zr1.76O7±y, all within the pyrochlore field in the ZrO2–PrOx phase diagram. Samples have been processed under four different atmospheres (O2, air, N2 and 5%H2(Ar)), so as to vary the environmental conditions from oxidising to reducing. Sample colouration ranged from dark brown to bright green, owing to varying Pr4+ content. A close correlation is found between the phase homogeneity, the microstructure and the Pr content. Pr–deficient samples present a homogeneous microstructural aspect and composition, whereas Pr–rich compositions always break into 5–25 µm–sized grains with pyrochlore phases at the grain centre and ill–crystallised, Pr–rich oxidised phases at the grain–boundaries. Raman spectroscopy shows that different types of oxygen disorder occur depending on composition and processing atmosphere: in Pr–poor samples oxygen interstitials are created to compensate for Zr4+ excess charge, whereas in Pr–rich samples oxygen disorder occurs around the Pr3+ or Pr4+ ions substituting for Zr4+, because of size–mismatch. Magnetic measurements showed a high Pr4+ content, which has been attributed to several factors: the highly oxidised state of the feedstock material, the segregation of Pr and O–rich grain boundaries in compositions with praseodymium molar rate> 0.5, and the lower oxide–ion conductivity for PZO compositions, compared to either Pr–poor or Pr–rich compositions. Post–processing thermal annealing in a vacuum at 1000 °C enabled total Pr reduction, with the exception of the Pr–rich P2.24 samples, where some Pr4+ ions remained in the oxidised state., We acknowledge financial support from the Spanish Government and Feder Funds (European Union) through projects MAT2016-77769R and PID2019-107106RB-C32. LG acknowledges the grant BES-2017-079683., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Directionally solidified cobalt-doped MgO-MgAl2O4 eutectic composites for selective emitters

  • Merino, R. I.
  • Oliete, Patricia B.
  • Moshtaghioun, Bibi Malmal
  • Sola, Daniel
  • Peña, J. I.
This article belongs to the Special Issue Advanced Characterization of Functional Materials., Cobalt-doped MgO-MgAl2O4 eutectic composites were explored for their use as selective emitters for thermophotovoltaic devices. Eutectic ceramic rods with different cobalt content were directionally solidified by using the laser floating zone technique at two processing rates to obtain microstructures with different domain sizes. Thermal emission between 1000 °C and 1500 °C and optical properties (reflectance and transmittance) at room temperature were measured in the Co-doped composites and the effect on microstructure and cobalt content was investigated. Thermal emission consisted of an intense broad band at about 1.67 µm matching with the bandgap of the InGaAs cell. The emission was ascribed to the de-excitation from the 4T1(F) multiplet to the 4A2(F) ground state of the thermally excited Co ions located in the tetrahedral sites of the MgAl2O4 phase. The selectivity of the thermal emission showed a decrease with the cobalt content due to the enhancement of other electronic transitions, which leads to keeping the cobalt content in these composites at low levels (<0.15% at Co) for their use as selective emitters., This research was funded by the Spanish Ministerio de Economía, Industria y Competitividad (MINECO) and the CE (FEDER FUNDS), grants number MAT2013-41045-R-EMITEME and MAT-2016-77769R-FLASCERAMAT. The Departamento de Ciencia, Universidad y Sociedad del Conocimiento del Gobierno de Aragón also contributed through the financial support to the Research Group T02-20R. B.M.M. wants to acknowledge the support of the Spanish MINECO by means of a “Juan de la Cierva- Incorporación” fellowship during her sabbatical stay in Zaragoza. D.S. thanks the PIT2 program of the University of Murcia´s own research plan., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Ceramic supports with highly dense and aligned pores for moltencarbonate based CO2 separation membranes

  • Merino, R. I.
  • Grima, Lorena
  • Oliete, Patricia B.
  • Orera, Alodia
  • Bucheli, Wilmer
  • Mutch, Greg A.
  • Papaioannou, Evangelos I.
  • Bailey, Josh J.
  • Kok, M. D.
  • Brett, D. J. L.
  • Shearing, P. R.
  • Metcalfe, Ian S.
  • Sanjuán, M. L.
Resumen del trabajo presentado a la XVII Conference Ceramics in Europe, celebrada en Krakow (Poland), del 10 al 14 de julio de 2022., Spanish Ministerio de Economía y Competitividad and Feder Funds grants MAT2016-77769R and BES-2017-079683; Departamento de Ciencia, Universidad y Sociedad del Conocimiento del Gobierno de Aragón through the financial support to the Research Group T02 20R., No
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Cerámicas con microestructura eutéctica producidas por solidificación direccional para aplicación en membranas selectivas al CO2

  • Oliete, Patricia B.
  • Orera, Alodia
  • Merino, R. I.
  • Grima, Lorena
  • Bucheli, Wilmer
  • Sanjuán, M. L.
Resumen del trabajo presentado al XVI Congreso Nacional de Materiales, celebrado en Ciudad Real del 28 de junio al 1 de julio de 2022., MAT2016-77769R, PID2019-107106RB-C32 y BES-2017-079683 (Ministerio de Economía y Competitividad y fondos Feder), Gobierno de Aragón (grupo T02 20R) y Servicio General de Apoyo a la Investigación (SAI) de la Universidad de Zaragoza., No
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Selective thermal emission of directionally solidified Al2O3/Y3-xErxAl5O12 eutectics: influence of the microstructure, temperature and erbium content

  • Oliete, P. B.
  • Orera, A.
  • Sanjuán, M. L.
  • Merino, R. I.
Directionally solidified eutectic rods of Al2O3-Y3-xErxAl5O12 (0 = x = 3) composition have been grown using the laser floating zone method at processing rates of 25 mm/h and 750 mm/h. For all the samples the microstructure presents the same morphology, consisting of an interpenetrated 3D eutectic network of both Al2O3 and garnet phases, while eutectic interspacing strongly depends on the solidification rate. Optical absorption, luminescence and thermal emission have been investigated as a function of the growth rate and the erbium content. From the luminescence characterization it can be concluded that erbium ions are present in the eutectic only in the garnet phase. Near infrared thermal emission has been measured at temperatures ranging from 1000 to 1500 °C. Selective emission consisting of an emission band at 1540 nm and a weaker line at 970 nm, ascribed to the radiative de-excitation of the thermally excited Er3+ ions from the 4I13/2 and 4I11/2 multiplets to the 4I15/2 ground state respectively, has been detected in all the samples containing erbium. The influence of the erbium content, the microstructure and the temperature on the thermal emission has been investigated. The strongest selective emission has been obtained for samples with x=3 although it does not increase proportionally to the erbium content. The thermal emission becomes more intense when the temperature is increased but the selective emission seems to saturate at temperatures higher than 1300 °C. This effect is especially noticeable for x=3 and is attributed to thermally activated non-radiative de-excitation channels. It is suggested that these channels become effective through energy transfer among Er3+ ions and towards killers.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Understanding the complex structural features and phase changes in Na 2 Mg 2 (SO 4 ) 3 : A combined single crystal and variable temperature powder diffraction and Raman spectroscopy study

  • Trussov, I.A.
  • Male, L.L.
  • Sanjuan, M.L.
  • Orera, A.
  • Slater, P.R.
Sodium mixed metal sulphates have attracted considerable attention, both in terms of mineralogy and more recently due to interest in Na ion containing materials for battery applications. The phase, Na 2 Mg 2 (SO 4 ) 3 , has been previously reported to undergo a phase change to langbeinite at high temperatures, which is interesting given that usually the langbeinite structure is only adopted when large alkali metal ions, e.g. K, Cs, are present. Nevertheless the room temperature structure of this phase has remained elusive, and so in this work, we report a detailed structural study of this system. We show that room temperature Na 2 Mg 2 (SO 4 ) 3 can only be prepared by quenching from high temperature, with slow cooling leading to phase separation to give the previously unreported systems, Na 2 Mg(SO 4 ) 2 and Na 2 Mg 3 (SO 4 ) 4 . We report the structures of quenched Na 2 Mg 2 (SO 4 ) 3 (monoclinic, P2 1 ), as well as Na 2 Mg(SO 4 ) 2 (triclinic, P1¯) and Na 2 Mg 3 (SO 4 ) 4 (orthorhombic, Pbca), detailing their complex structural features. Furthermore, we report a study of the thermal evolution of quenched Na 2 Mg 2 (SO 4 ) 3 with temperature through variable temperature XRD and Raman studies, which shows a complex series of phase transitions, highlighting why this phase has proven so elusive to characterise previously, and illustrating the need for detailed characterisation of such sulphate systems.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Non-Hall-Petch hardness dependence in ultrafine fibrous MgAl 2 O 4 -MgO eutectic ceramics fabricated by the laser-heated floating zone (LFZ) method

  • Moshtaghion, B.M.
  • Peña, J.I.
MgAl 2 O 4 -MgO eutectic ceramics were fabricated by the laser-heated floating zone (LFZ) method with various growth rates to assess its possible beneficial effect on microstructural aspects and mechanical properties. It was determined that the growth rate optimizing the microstructure and mechanical properties is 750 mm/h; below this value, coarsening of the fibrous microstructure takes place with a degradation of these properties. In the extreme case of 50 mm/h growth rate, the presence of undesirable transverse cracks was unavoidable. Thanks to the high growth rate of 750 mm/h, ultra-fine fibrous microstructure MgAl 2 O 4 -MgO eutectic ceramics can thus be fabricated with greater hardness (15.5 GPa from Vickers indentation and 22 GPa from nanoindentation) and flexural strength (˜345 MPa). It is reported that hardness scales with the interfiber spacing ¿ according to a law of the type ln¿/¿, contrary to the assumed Hall-Petch-like dependence. This proposed law can be explained in terms of dislocation hardening induced by the MgO fibers.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Influence of microstructural size on the thermal shock behavior of Al2O3-Er3Al5O12 directionally solidified eutectics

  • Nie, Y.
  • Oliete, P.B.
  • Merino, R.I.
We analyze the thermal shock resistance of directionally solidified eutectics. When quenching in water, the resistance starts to deteriorate with temperature differences in the range 260 to 300 K, almost independent of the microstructure size (or initial flexural strength). Unlike other strong, dense ceramics, the loss of strength is gradual upon quenching in boiling water. The onset of crack propagation seems to be controlled by the mismatch of the thermal and elastic properties of the component phases, while the length of the propagated cracks is limited by their quantity, which is estimated to scale approximately with the interface density.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Medium infrared transparency of MgO-MgAl2O4 directionally solidified eutectics

  • Moshtaghioun, Bibi Malmal
  • Peña, José I.
  • Merino, Rosa I.
MgAl2O4-MgO eutectic ceramics have been fabricated by the laser floating zone method. Increasing growth rates from 10 to 50 mm/h, the microstructure transformed from irregular MgO rod-to-lamellae phase and it approached to almost homogeneous rod morphology. At the highest used velocity of 750 mm/h, the cell structure was completely dominant and the samples were free from transversal cracks. Although the highest flexure strength was found at 750 mm/h growth rate, the maximum optical transmittance in the medium-infrared range was obtained for 50 mm/h growth rate and for 1 mm thick samples reached values higher than 75% in the wavelengths between 4 and 5.3 µm. The enhanced transmittance for the sample with 50 mm/h growth rate can be explained in terms of the close refraction indexes of the component phases and the characteristic lengths of the resulting microstructure showing fully dense ceramics with the finest and almost homogeneous microstructure.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Directionally solidified Ni doped MgO-MgSZ eutectic composites for thermophotovoltaic devices

  • Sola, D.
  • Oliete, P.B.
  • Peña, J. I.
  • Merino, R.I.
Ni-doped MgO-MgSZ eutectic composites were investigated as selective emitters for thermophotovoltaic devices. MgO-MgSZ:Ni eutectic rods were directionally solidified at 25 and 500 mm/h using the laser floating zone technique. Microstructure was strongly dependent on the growth rate, the size of the eutectic phases decreased as the growth rate increased. A hardness of ~11 GPa and a fracture toughness of ~1.6 MPa were obtained from indentation techniques, not showing dependence on the growth rate. Flexure strength increased from ~400 MPa in samples grown at 25 mm/h up to ~1 GPa for those solidified at 500 mm/h, which was attributed to the decrease of the phase size. Thermal emission of eutectic composites was studied up to 1400 °C. An intense broad emission band centred in 1.5 µm matching with the sensitive region of the GaSb photoconverter was found. The selective emission was ascribed to the de-excitation of the thermally excited Ni2+ ions.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Spectroscopic insight into the interplay between structural disorder and oxidation degree in melt-grown Ce0.5Zr0.5O2-y compounds

  • Oliete, Patricia B.
  • Orera, Alodia
  • Sanjuán, María Luisa
The oxygen storage capacity of CexZr1-xO2-y compounds arises from the mixed-valent character of cerium, which makes the system sensitive to external factors such as temperature and oxygen partial pressure through their influence in the Ce valence, cation ordering and oxygen content. In this work, we analyze the phase relations in Ce0.5Zr0.5O2-y compounds fabricated by the laser floating zone technique in either oxidising or reducing atmosphere. Chemical, structural, and microstructural properties are studied by X-ray diffraction, thermogravimetry, scanning electron microscopy (energy dispersive X-ray and electron backscatter diffraction), and Raman spectroscopy. The latter proves to be determinant to discriminate between phases arising from subtle variations of atomic distribution that are hardly distinguished by X-ray diffraction or energy dispersive X-ray analyses. Cation disordered, fluorite-like phases are obtained when processing is performed in air, whereas cation-ordered, pyrochlore-related phases are formed when processing in Ar+5%H2 atmosphere. Processing in a low but non-negligible pO2 yields, besides the pyrochlore and fluorite-like phases, an intermediate state with partial disorder that may be relevant for catalysis applications. The vibrational Raman spectrum of the Ce2Zr2O7 pyrochlore has been fully interpreted through polarisation measurements at room and low temperature. Bands arising from crystal field transitions within the ground and first excited multiplets of Ce3+ ions are also identified. The electronic Raman spectrum is found to be a sensitive probe of the degree of cation and oxygen order in these compounds.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Mg2SiO4-MgAl2O4 directionally solidified eutectics: Hardness dependence modelled through an array of screw dislocations

  • Moshtaghioun, B.M.
  • Gomez-Garcia, D.
  • Peña, J.I.
Mg2SiO4-MgAl2O4 eutectic ceramics have been fabricated by means of the laser floating zone (LFZ) technique. The microstructure has revealed as an unusual one at lower growth rate, composed of broken lamellae of MgAl2O4 distributed randomly along one matrix, composed of Mg2SiO4. At higher growth rates, a cell structure with intra-cell lamella structure is dominant. Contrary to most eutectic systems, hardness is not dependent upon the inter-spacing, but it does depend on one characteristic length of lamellae: their perimeter. One simple model based upon the dislocation is proposed, which successfully accounts for such extraordinary hardness law. Accordingly, Mg2SiO4-MgAl2O4 eutectic ceramics fabricated at 50 mm/h growth rate with the smallest MgAl2O4 lamella perimeter favorably showed more elevated hardness (13.4 GPa from Vickers indentation and 15.3 GPa from nanoindentation) and strength (~430 MPa) than those found in the monolithic Mg2SiO4 matrix.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High CO2 permeability in supported molten-salt membranes with highly dense and aligned pores produced by directional solidification

  • Grima, L
  • Mutch, GA
  • Oliete, PB
  • Bucheli, W
  • Merino, RI
  • Papaioannou, EI
  • Bailey, JJ
  • Kok, MD
  • Brett, DJL
  • Shearing, PR
  • Metcalfe, IS
  • Sanjuan, ML
Composite molten salt-ceramic membranes are promising devices for high-temperature CO2 separation. Intensive material properties impact on separation performance as do membrane geometry (thickness) and microstructure (pore volume fraction, size, connectivity, and tortuosity factor). Although controlling pore size is considered somewhat routine, achieving pore alignment and connectivity is still challenging. Here we report the production of the first gas separation membrane using a porous ceramic matrix obtained from a directionally-solidified magnesium-stabilised zirconia (MgSZ) - MgO fibrilar eutectic as the membrane support. MgO was removed from the parent material by acid-etching to create a porous matrix with highly aligned pores with diameters of similar to 1 mu m. X-ray nano-computed tomography of a central portion (similar to 32, 000 mu m(3)) of the support identified similar to 21% porosity, with all pores aligned within 10 degrees and similar to 76% percolating along the longest sampled length. Employing the matrix as a support for a carbonate molten salt, a high CO2 permeability of 1.41x10(-10) mol m(-1).s(-1).Pa-1 at 815 degrees C was achieved, among the highest reported for supported molten-carbonate membranes (typically 10(-12) to 10(-10) mol m(-1).s(-1).Pa-1 at similar temperatures). We suggest that the high permeability is attributable to the excellent pore characteristics resulting from directional solidification, namely a dense array of parallel, micron-scale pores connecting the feed and permeate sides of the membrane.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Pyrochlore-like ZrO2-PrOx compounds: The role of the processing atmosphere in the stoichiometry, microstructure and oxidation state

  • Grima, L.
  • Peña, J.I.
  • Sanjuán, M.L.
The object of this work is to study the relation between composition, microstructure and oxidation state of Pr2±xZr2∓xO7±y materials produced by the laser–floating zone (LFZ) technique. Three compositions are studied, nominally Pr1.7Zr2.3O7+y, Pr2Zr2O7+y and Pr2.24Zr1.76O7±y, all within the pyrochlore field in the ZrO2–PrOx phase diagram. Samples have been processed under four different atmospheres (O2, air, N2 and 5%H2(Ar)), so as to vary the environmental conditions from oxidising to reducing. Sample colouration ranged from dark brown to bright green, owing to varying Pr4+ content. A close correlation is found between the phase homogeneity, the microstructure and the Pr content. Pr–deficient samples present a homogeneous microstructural aspect and composition, whereas Pr–rich compositions always break into 5–25 µm–sized grains with pyrochlore phases at the grain centre and ill–crystallised, Pr–rich oxidised phases at the grain–boundaries. Raman spectroscopy shows that different types of oxygen disorder occur depending on composition and processing atmosphere: in Pr–poor samples oxygen interstitials are created to compensate for Zr4+ excess charge, whereas in Pr–rich samples oxygen disorder occurs around the Pr3+ or Pr4+ ions substituting for Zr4+, because of size–mismatch. Magnetic measurements showed a high Pr4+ content, which has been attributed to several factors: the highly oxidised state of the feedstock material, the segregation of Pr and O–rich grain boundaries in compositions with praseodymium molar rate> 0.5, and the lower oxide–ion conductivity for PZO compositions, compared to either Pr–poor or Pr–rich compositions. Post–processing thermal annealing in a vacuum at 1000 °C enabled total Pr reduction, with the exception of the Pr–rich P2.24 samples, where some Pr4+ ions remained in the oxidised state.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Can Y2O3-MgO eutectics be new promising structural and optical ceramics?

  • Moshtaghioun B. M.
  • Peña J. I.
  • Merino R. I.
The manuscript addresses the solidification of Y2O3-MgO eutectic composites for the first time, and the study of their microstructure, mechanical properties and infrared transmittance. The composites with eutectic composition (20 % vol MgO) have been solidified using the laser floating zone method, at solidification rates between 25 mm/h and 750 mm/h. Their microstructure has been quantified and the conditions for coupled or cellular regime determined. They are dense, with elastic modulus, as determined from nanoindentation tests of around 200 GPa. The highest 3-point flexural strength (256±25 MPa) values and highest infrared optical transmittance has been observed for the material solidified with the finest, still homogeneous microstructure that could be achieved. This microstructure, which is achieved at a solidification rate of 50mm/h, consists of MgO fibers of 600 nm diameter embedded in the Y2O3 matrix. The thin MgO rods and the associated residual stress field contribute to the material strength as they deviate the propagating crack. The Vickers Hardness ranged from 9.5 to 11.5 GPa, with mild increase with the decrease of the microstructural size which has been rationalized as the MgO rods blocking the movement of dislocations in the matrix, as in other studied composites. Indentation fracture toughness values around 3 MPa.m1/2, independent of the sample microstructure, have been measured. In the longitudinal direction transmittance values higher than 80 % in the wavelength range from 3.5 to 7 µm, for 1 mm thick slices have been measured. Light scattering limits the short wavelength cut-off to around 2 µm for light travelling in the longitudinal direction, while a transmittance gap is observed in the transverse direction, of photonic crystal like nature.