Skip to main content

SPARK PLASMA SINTERING COMO MEDIO DE PREPARACION DE MATERIALES MAGNETOELECTRICOS EN CAPAS: FASES UNICAS Y COMPOSITES MULTIFERROICOS ESTRUCTURADOS EN DISTINTAS ESCALAS

MAT2017-88788-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2017
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 26
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Mechanosynthesis of the Whole Y1−xBixMn1−xFexO3 Perovskite System: Structural Characterization and Study of Phase Transitions

  • Quintana-Cilleruelo, Jose Ángel
  • Veerapandiyan, Vignaswaran K.
  • Deluca, Marco
  • Algueró, Miguel
  • Castro, Alicia
Perovskite BiFeO3 and YMnO3 are both multiferroic materials with distinctive magnetoelectric coupling phenomena. Owing to this, the Y1xBix Mn1xFexO3 solid solution seems to be a promising system, though poorly studied. This is due to the metastable nature of the orthorhombic perovskite phase of YMnO3 at ambient pressure, and to the complexity of obtaining pure rhombohedral phases for BiFeO3-rich compositions. In this work, nanocrystalline powders across the whole perovskite system were prepared for the first time by mechanosynthesis in a high-energy planetary mill, avoiding high pressure and temperature routes. Thermal decomposition temperatures were determined, and structural characterization was carried out by X-ray powder diffraction and Raman spectroscopy on thermally treated samples of enhanced crystallinity. Two polymorphic phases with orthorhombic Pnma and rhombohedral R3c h symmetries, and their coexistence over a wide compositional range were found. A gradual evolution of the lattice parameters with the composition was revealed for both phases, which suggests the existence of two continuous solid solutions. Following bibliographic data for BiFeO3, first order ferroic phase transitions were located by differential thermal analysis in compositions with x 0.9. Furthermore, an orthorhombic-rhombohedral structural evolution across the ferroelectric transition was characterized with temperature-dependent X-ray diffraction., This work has been funded by the MICINNU (Spain) through the MAT2014-58816-R and MAT2017-88788-R projects. Jose Ángel Quintana-Cilleruelo is grateful for the financial support by the Spanish MINECO (BES-2015-072595). Vignaswaran K. Veerapandiyan and Marco Deluca gratefully acknowledge support from the Austrian Science Fund (FWF): Proyect P29563-N36., We acknowledge support by the CSIC Open Access Publication Initiative through its Unit of Information Resources for Research (URICI), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhanced piezomagnetic coefficient of cobalt ferrite ceramics by Ga and Mn doping for magnetoelectric applications

  • Santa-Rosa, Washington
  • da-Silva, Jr. Paulo Sergio
  • M’Peko, Jean-Claude
  • Amorín, Harvey
  • Algueró, Miguel
  • Venet, Michel
See the supplementary material for XRD patterns and SEM micrographs of CFG and CFM compositions. [ftp://ftp.aip.org/epaps/journ_appl_phys/E-JAPIAU-125-083908], [EN] The magnetic, magnetostrictive, and electrical properties of Ga- and Mn-doped cobalt ferrite are reported as a function of composition. Materials with improved functionality for magnetoelectric composites are obtained. Magnetic characterizations reveal the effectiveness of the dopants to reduce the typically high magneto-crystalline anisotropy of cobalt ferrite and significantly enhance piezomagnetic coefficients. CoGa0.15Fe1.85O4 ceramic shows large effective piezomagnetic coefficient q11, 3.9 × 10−6 kA−1 m, which is among the highest values reported for cobalt ferrite-based ceramics. Additionally, a two order of magnitude increase of resistivity is found after doping, which makes this material specially suitable for particulate composites. On the contrary, CoMn0.25Fe1.75O4 ceramic has the highest value of q11+q21 (∼1.9 × 10−6 kA−1 m), which is the relevant parameter for laminated composites. Analytical calculations of the transverse magnetoelectric coefficient αE31 for bilayers containing these optimized magnetostrictive phases are also reported, and they demonstrate their high potential for developing new magnetoelectric composites., The research was co-funded by the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior, Brasil (CAPES) —Finance Code 001 (Process No. 8881.030500/2013-01), São Paulo Research Foundation FAPESP (Grant Nos. 2013/00134-7and 2017/17872-1), and Spanish MINECO (Project Nos. MAT2014-58816-R and MAT2017-88788-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Processing issues and their influence in the magnetoelectric performance of (K,Na)NbO3/CoFe2O4-based layered composites

  • Santa-Rosa, Washington
  • Venet, Michel
  • M’Peko, Jean-Claude
  • Amorín, Harvey
  • Algueró, Miguel
Low temperature processing of environmentally-friendly (K,Na)NbO- and CoFeO-based layered composites has been accomplished by hot pressing, and their electrical, piezoelectric and magnetoelectric properties have been characterized. High quality composite three-layer CoFeO/KNaNbO/CoFeO structures with defect-free interfaces were obtained by hot pressing at only 1000 °C, when highly reactive CoFeO powders obtained by Pechini were used. Negligible chemical reactions at interfaces or interdiffusion across them took place during processing, while alkali volatilization was minimized. Dense, crack-free CoFeGaO/(KNa)LiNbTaO/CoFeGaO structures incorporating phases with enhanced piezoresponses have been also obtained, though in this case magnetoelectric coefficients were lower than expected. This is shown to be related with the presence of a core-shell type microstructure within the piezoelectric layer characteristic of (KNa)LiNbTaO, which is stabilized by the low temperature processing. Procedures for further enhancement of the magnetoelectric response are proposed., Research funded by Brazilian PVE/CAPES (process88881.030500/2013-01) and grant #2013/00134-7 Sao Paulo Research Foundation (FAPESP) and by Spanish MINECO through projects MAT2014-58816-R and MAT2017-88788-R., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Environmentally-friendly magnetoelectric ceramic multilayer composites by water-based tape casting

  • Santa-Rosa, Washington
  • Venet, Michel
  • M'Peko, Jean-Claude
  • Moreno, Rodrigo
  • Amorín, Harvey
  • Algueró, Miguel
Supplementary data associated with this article can be found, in theonline version, at: https://doi.org/10.1016/j.jeurceramsoc.2018.10.009, Magnetoelectric composites are an enabling material technology for a range of novel devices like electrically-tunable magnetic microwave components or room-temperature-operation high-sensitivity magnetic sensors. Among the different approaches under development, cofired ceramic layered composites provide large effective magnetoelectric coefficients and improved reliability. However, miniaturization and processing up-scaling remain an issue. This can be addressed by using tape casting technology to prepare multilayer structures, as it is industrially done for multilayer ceramic capacitors. We report here the processing of ceramic multilayer composites of environmentally-friendly piezoelectric (KNa)LiNbTaO and magnetostrictive CoFeMnO by water-based tape casting. Dense ceramic multilayers with high quality interfaces were obtained, and their functional response characterized. Effects of the multilayer geometry, characterized by ceramic layer thickness of tens of microns and large number of layers, have been defined. A distinctive enhancement of functionality as compared with conventionally-prepared layered structures is demonstrated and related to strain/stress relaxation characteristics across layers., Research co-funded by the Coordenação de Aperfeiçoamento dePessoal de Nível Superior–Brasil (CAPES)–Finance Code 001 (process88881.030500/2013-01), São Paulo Research Foundation FAPESP(grants #2013/00134-7 and #2017/17872-1), and Spanish MINECO (projects MAT2014-58816-R and MAT2017-88788-R)., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Evidence of Kittel type behaviour of the permittivity of a nanostructured high sensitivity piezoelectric

  • Balciunas, Sergejus
  • Ivanov, Maksim
  • Grigalaitis, Robertas
  • Banys, Juras
  • Amorín, Harvey
  • Castro, Alicia
  • Algueró, Miguel
The broadband dielectric properties of high sensitivity piezoelectric 0.36BiScO-0.64PbTiO ceramics with average grain sizes from 1.6 μm down to 26 nm were investigated in the 100-500 K temperature range. The grain size dependence of the dielectric permittivity was analysed within the effective medium approximation. It was found that the generalised core-shell (or brick wall) model correctly explains the size dependence down to the nanoscale. For the first time, the grain bulk and boundary properties were obtained without making any assumptions of values of the parameters or simplifications. Two contributions to dielectric permittivity of the grain bulk are described. The first is the size-independent one, which follows the Curie-Weiss law. The second one is shown to plausibly follow the Kittel's law. This seems to suggest the unexpected persistence of mobile ferroelectric domains at the nanoscale (26 nm grains). Alternative explanations are discussed., This work was supported by project TUMOCS. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie [Grant Agreement No. 645660]. Financial support of the Spanish MINECO (Project Nos. MAT2014-58816-R and MAT2017-88788-R) and the collaboration in the frame of COST MP0904 Action are highly acknowledged., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

The Polar/Antipolar Phase Boundary of BiMnO3–BiFeO3–PbTiO3: Interplay among Crystal Structure, Point Defects, and Multiferroism

  • Fernández-Posada, Carmen M.
  • Castro, Alicia
  • Kiat, Jean-Michel
  • Porcher, Florence
  • Peña, Octavio
  • Jiménez, Ricardo
  • Algueró, Miguel
  • Amorín, Harvey
The ferromagnetic perovskite oxide BiMnO is a highly topical material, and the solid solutions it forms with antiferromagnetic/ferroelectric BiFeO and with ferroelectric PbTiO result in distinctive polar/nonpolar morphotropic phase boundaries (MPBs). The exploitation of such a type of MPBs could be a novel approach to engineer novel multiferroics with phase-change magnetoelectric responses, in addition to ferroelectrics with enhanced electromechanical performance. Here, the interplay among crystal structure, point defects, and multiferroic properties of the BiMnO–BiFeO–PbTiO ternary system at its line of MPBs between polymorphs of tetragonal P4mm (polar) and orthorhombic Pnma (antipolar) symmetries is reported. A strong dependence of the phase coexistence on thermal history is found: phase percentage significantly changes whether the material is quenched or slowly cooled from high temperature. The origin of this phenomenon is investigated with temperature-dependent structural and physical property characterizations. A major role of the complex defect chemistry, where a Bi/Pb-deficiency allows Mn and Fe ions to have a mixed-valence state, in the delicate balance between polymorphs is proposed, and its influence in the magnetic and electric ferroic orders is defined., This work was supported by the Spanish MINECO through projects MAT2014‐58816‐R and MAT2017‐88788‐R., Peer Reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Lead-Free BNT–BT0.08/CoFe2O4 Core–Shell Nanostructures with Potential Multifunctional Applications

  • Cernea, Marin
  • Radu, Roxana
  • Amorín, Harvey
  • Greculeasa, Simona Gabriela
  • Vasile, Bogdan Stefan
  • Surdu, Vasile Adrian
  • Ganea, Paul
  • Trusca, Roxana
  • Hattab, Marwa
  • Galassi, Carmen
© 2020 by the authors., Herein we report on novel multiferroic core–shell nanostructures of cobalt ferrite (CoFe2O4)–bismuth, sodium titanate doped with barium titanate (BNT–BT0.08), prepared by a two–step wet chemical procedure, using the sol–gel technique. The fraction of CoFe2O4 was varied from 1:0.5 to 1:1.5 = BNT–BT0.08/CoFe2O4 (molar ratio). X–ray diffraction confirmed the presence of both the spinel CoFe2O4 and the perovskite Bi0.5Na0.5TiO3 phases. Scanning electron microscopy analysis indicated that the diameter of the core–shell nanoparticles was between 15 and 40 nm. Transmission electron microscopy data showed two–phase composite nanostructures consisting of a BNT–BT0.08 core surrounded by a CoFe2O4 shell with an average thickness of 4–7 nm. Cole-Cole plots reveal the presence of grains and grain boundary effects in the BNT–BT0.08/CoFe2O4 composite. Moreover, the values of the dc conductivity were found to increase with the amount of CoFe2O4 semiconductive phase. Both X-ray photoelectron spectroscopy (XPS) and Mössbauer measurements have shown no change in the valence of the Fe3+, Co2+, Bi3+ and Ti4+ cations. This study provides a detailed insight into the magnetoelectric coupling of the multiferroic BNT–BT0.08/CoFe2O4 core–shell composite potentially suitable for magnetoelectric applications., The authors gratefully acknowledge the financial support from Core Program PN19–0.3 (Contract No. 21 N/08.02.2019) from the Romanian Ministry of Research. R. Radu is most thankful to R.M. Costescu for her engagement in performing XPS measurements. The SEM spectroscopy characterization was possible due to the Project POSCCE, No.638/12.03.2014. H. Amorín acknowledges financial support from Spanish MINECO project MAT2017-88788-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Delicate Balance among Three Ferroic Polymorphic Phases in BiFeO3-BiMnO3-PbTiO3

  • Fernández-Posada, Carmen M.
  • Castro, Alicia
  • Peña, Octavio
  • Algueró, Miguel
  • Amorín, Harvey
Phase-change functional responses can be obtained in perovskite solid solutions at structural instabilities involving multiferroic states, a very promising approach for realizing magnetoelectric effects at room temperature. A line of multiferroic morphotropic phase boundaries (MPBs) has been described within the phase diagram of the BiFeO-BiMnO-PbTiO ternary system, in which an evolution from Cc/P4mm-type (polar/polar) to Pnma/P4mm-type (antipolar/polar) MPBs takes place. Coexistence of the three polymorphs results in a small region, where distinctive phase-change magnetoelectric responses are anticipated. In this work, all three polymorphs were obtained, either isolated or in phase coexistence with varying percentages, by tailoring the cooling profile after high-temperature annealing in a small compositional range. The perovskite structure was characterized, and temperature-dependent magnetic and electrical characterizations were carried out to define the ferroic orders and crystal physicochemical properties of the three polymorphs. Results revealed the close interplay among the crystal structure, point defects, and multiferroism in this small region, where the delicate balance among the three polymorphs is shown. Additionally, the effect of size reduction across the submicron range, down to the nanoscale, is described and discussed., Funded by Spanish MINECO through projects MAT2014-58816-R and MAT2017-88788-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Selection and optimization of a K0.5Na0.5NbO3-based material for environmentally-friendly magnetoelectric composites

  • Venet, Michel
  • Santa-Rosa, Washington
  • da-Silva, Jr. Paulo Sergio
  • M’Peko, Jean-Claude
  • Ramos, Pablo
  • Amorín, Harvey
  • Algueró, Miguel
[EN] Li-and Ta-modified KNaNbO compounds are among the most promising lead-free ferroelectrics for high-sensitivity piezoelectric ceramic materials, and are potentially capable of replacing Pb(Zr, Ti)O. They are also being investigated as piezoelectric components in environmentally friendly magnetoelectric composites. However, most suitable modifications for this application have not been identified. We report here a simulation study of how the magnetoelectric voltage responses of layered composite structures based on Lix(KNa)NbTayO varies with the chemical composition of the piezoelectric. Instead of relying on material coefficients from the literature, which would have required using different sources, an ad hoc set of materials was prepared. This demanded tailoring preparation by conventional means to obtain dense ceramics while controlling alkali volatilization, perovskite phase and microstructure, as well as characterizing their dielectric, elastic and electromechanical properties. This provided the set of relevant material coefficients as a function of composition, which was used to obtain the magnetoelectric responses of model layered structures including a reference magnetostrictive spinel oxide by simulation. The piezoelectric material leading to the highest magnetoelectric coefficient was identified, and shown to be different to that showing the highest piezoelectric coefficient. This reflects the dependence of the magnetoelectric response on all material coefficients, along with the complex interplay between composition, processing and properties in KNaNbO-based ceramics., The research was co-funded by the Coordenação de Aperfeiçoamento de Pessoal de Nível Superior, Brasil (CAPES)—Finance Code 001 (process number 88881.030500/2013-01), the São Paulo Research Foundation FAPESP (grant numbers 2013/00134-7 and 2017/17872-1), and Spanish MINECO (project MAT2017-88788-R).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

A glance at processing-microstructure-property relationships for magnetoelectric particulate PZT-CFO composites

  • Galizia, Pietro
  • Baldisserri, Carlo
  • Mercadelli, Elisa
  • Capiani, Claudio
  • Galassi, Carmen
  • Algueró, Miguel
[EN] In this work, we investigated the processing-microstructure-property relationships for magnetoelectric (ME) particulate composites consisting of hard ferromagnetic CoFeO (CFO) particles dispersed in a Nb-doped PbZrTiO (PZT) soft ferroelectric matrix. Several preparation steps, namely PZT powder calcination, PZT-CFO mixture milling and composite sintering were tailored and a range of microstructures was obtained. These included open and closed porosities up to full densification, PZT matrices with decreasing grain size across the submicron range down to the nanoscale and well dispersed CFO particles with bimodal size distributions consisting of submicron and micron sized components with varying weights. All samples could be poled under a fixed DC electric field of 4 kV/mm and the dielectric, piezoelectric and elastic coefficients were obtained and are discussed in relation to the microstructure. Remarkably, materials with nanostructured PZT matrices and open porosity showed piezoelectric charge coefficients comparable with fully dense composites with coarsened microstructure and larger voltage coefficients. Besides, the piezoelectric response of dense materials increased with the size of the CFO particles. This suggests a role of the conductive magnetic inclusions in promoting poling. Magnetoelectric coefficients were obtained and are discussed in relation to densification, piezoelectric matrix microstructure and particle size of the magnetic component. The largest magnetoelectric coefficient ff33 of 1.37 mV cm Oe was obtained for submicron sized CFO particles, when closed porosity was reached, even if PZT grain size remained in the nanoscale., This research was funded by Spanish MICINN grant number MAT2017-88788-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Ceramic processing and multiferroic properties of the perovskite YMnO3-BiFeO3 binary system

  • Quintana-Cilleruelo, Jose Ángel
  • Castro, Alicia
  • Amorín, Harvey
  • Veerapandiyan, Vignaswaran K.
  • Deluca, Marco
  • Peña, Octavio
  • Algueró, Miguel
[EN] The perovskite (1-x)YMnO3-xBiFeO(3) binary system is very promising because of its multiferroic end members. Nanocrystalline phases have been recently obtained by mechanosynthesis across the system, and the perovskite structural evolution has been described. Two continuous solid solutions with orthorhombic Pnma and rhombohedral R3c symmetries were found, which coexist within a broad compositional interval of 0.5 <= x <= 0.9. This might be a polar-nonpolar morphotropic phase boundary region, at which strong phase-change magnetoelectric responses can be expected. A major issue is phase decomposition at moderate temperatures that highly complicates ceramic processing. This is required for carrying out a sound electrical characterization and also for their use in devices. We present here the application of Spark Plasma Sintering to the ceramic processing of YMnO3-BiFeO3 phases. This advanced technique, when combined with nanocrystalline powders, allowed densifying phases at reduced processing temperatures and times, so that perovskite decomposition was avoided. Electrical measurements were accomplished, and the response was shown to be mostly dominated by conduction. Nonetheless, the intrinsic dielectric permittivity was obtained, and a distinctive enhancement in the phase coexistence region was revealed. Besides, Rayleigh-type behavior characteristic of ferroelectrics was also demonstrated for all rhombohedral phases. Magnetic characterization was performed in this region, and antiferromagnetism was shown., Austrian Science Fund, Grant/Award Number: P29563-N36; Spanish MICINNU, Grant/Award Number: MAT2017-88788-R; Spanish MINECO, Grant/Award Number: BES-2015-072595
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Novel Aurivillius Bi4Ti3_2xNbxFexO12 phases with increasing magnetic-cation fraction until percolation: a novel approach for room temperature multiferroism

  • Algueró, Miguel
  • Pérez-Cerdán, Miguel
  • Pérez del Real, Rafael
  • Ricote, J.
  • Castro, Alicia
[EN] Aurivillius oxides with general formula (BiO)(ABO) are being extensively investigated for room-temperature multiferroism and magnetoelectric coupling. The chemical design strategy behind current investigations is the incorporation of magnetically active BiMOunits (M: Fe, Mn, Co…) to the pseudoperovskite layer of known ferroelectrics like BiTiO, increasingm. The percolation of magnetic cations at the B-site sublattice is required for magnetic ordering and thus, phases withm≥ 5 are searched. Alternatively, one can try to directly substitute magnetic species for Tiin the perovskite slab, without introducing additional oxygen octahedra. We report here the mechanosynthesis of Aurivillius BiTiNbFeOphases with increasingxvalues up to 1. A maximum magnetic fraction of 1/3, surpassing the threshold for percolation, was reached. Preliminary structural analysis indicated a continuous solid solution, though hints of structural changes betweenx= 0.25 and 0.5 were found. Ceramic processing was accomplished by spark plasma sintering of the mechanosynthesized phases, including those with high-xones with reduced thermal stability. This has enabled us to carry out full electrical characterization and to demonstrate ferroelectricity for all phases up tox= 1. Magnetic measurements were also carried out, and weak ferromagnetism was found forx= 1. Therefore, BiTiNbFeOis proposed to be a novel room-temperature multiferroic., Research is funded by Spanish MICINN through project MAT2017-88788-R. Technical support by Ms I. Martínez, at ICMM-CSIC is also acknowledged., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Magnetic properties across the YMnO3-BiFeO3 system designed for phase-change magnetoelectric response

  • Algueró, Miguel
  • Quintana-Cilleruelo, Jose Ángel
  • Peña, O.
  • Castro, Alicia
[EN] Perovskite systems with structurally different multiferroic end members are being extensively investigated, because large phase-change magnetoelectric responses have been anticipated at the morphotropic phase boundaries (MPBs) between polymorphic forms with differentiated ferroic orderings. (1-x) YMnO-x BiFeO is one such system, for which two continuous perovskite solid solutions with rhombohedral R3c and orthorhombic Pnma symmetries are present, and coexist across a wide compositional range. This might be a discontinuous MPB between a non-polar and a polar phase, at which the orthorhombic to rhombohedral transition may be electrically induced with a distinctive magnetic signature. In order to explore this possibility, magnetic properties have been characterized across the whole system, and relationships between perovskite crystal structure and magnetism have been established. Distinctive evolutions within each solid solution are revealed that define a region between x = 0.6 and 0.9, where a non-polar orthorhombic ferromagnetic phase coexists with a polar rhombohedral antiferromagnetic one at room temperature., Research funded by Spanish MICINN through project MAT2017-88788-R. J.A. Quintana-Cilleruelo also recognizes additional funding by Spanish MINECO (grant BES-2015-072595), and training in JANA2006 during a two-month research stay at Ecole Centrale Paris under the supervision of Dr. Brahim Dkhil. Technical support by Ms. I. Martínez at ICMM-CSIC, and magnetic data acquisition by Mr. T. Guizouarn at ISCR are greatly acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Controlling colloidal processing of (K,Na)NbO3-based materials in aqueous medium

  • Venet, Michel
  • Santa-Rosa, Washington
  • M'Peko, Jean-Claude
  • Amorín, Harvey
  • Algueró, Miguel
  • Moreno, Rodrigo
[EN] K0:5Na0:5NbO3-based materials are serious candidates to replace leadbased piezoceramics since they show excellent electrical and piezoelectric properties. The tape casting technique can be used to obtain highly textured KNN-based ceramics; however, despite industrial and environmental advantages of water-based processing, there are not reports about the control of colloidal processing conditions to obtain optimized K0:5Na0:5NbO3-based slurries in aqueous medium. This paper reports a procedure for controlling colloidal stability and rheological behavior of aqueous (K0:5Na0:5)0:97Li0:03Nb0:8Ta0:2O3 suspensions. Zeta potential and cationic solubility measurements as a function of pH showed that pH 8.5 is adequate for concentrated suspensions, while ow curves analysis allowed optimizing processing parameters, such as, powder content, amount of de occulant and binder, and sonication time. Optimized colloidal suspensions were prepared and used to obtain high quality tapes. Processed ceramics from these stacked tapes show equivalent properties to those processed directly from powders, which demonstrates the effectiveness of the colloidal route reported here., Research co-funded by the Coordenacao de Aperfeicoamento de Pessoal de Nivel Superior - Brasil (CAPES) - Finance Code 001 (process 88881.030500/2013-01), Sao Paulo Research Foundation FAPESP (grants#2013/00134-7 and #2017/17872-1), and Spanish MINECO (projects MAT2014-58816-R, MAT2015-67586-CR-2-R, and MAT2017-88788-R).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Enhanced magnetoelectric response of cofired ceramic layered composites by adjusting the grain boundary conductivity of the magnetostrictive component

  • Venet, Michel
  • Santa-Rosa, Washington
  • Amorín, Harvey
  • Ramos, Pablo
  • Algueró, Miguel
[EN] Magnetoelectric composites provide large enough room-temperature functional responses to enable a range of novel technologies, like uncooled high-sensitivity magnetic sensors. Magnetoelectricity in these composites appears as a product property of the piezoresponses of two elastically coupled ferroic phases. Coefficients then depend not only on the magnetostriction and piezoelectricity of the components, but also on interface quality. Different composite approaches are under development, among which cofired ceramic layered structures of ferrimagnetic spinel and ferroelectric perovskite oxides stand out because direct bonding between phases is attained, which facilitates miniaturization. An aspect rarely investigated is the role of the electrical characteristics of the magnetostrictive material beyond their effect on ferroelectric poling. We report here a three-fold enhancement of magnetoelectric coefficients by the only adjustment of the grain boundary conductivity of the spinel oxide. Significant differences in poling level are ruled out, and the effect is related with changes in the composite effective permittivity., This work was supported by the Coordenaçao de Aperfeiçoamento de Pessoal de Nível Superior, Brasil (CAPES) - Finance Code 001 (Process No. 88881.030500/2013–01), Sao Paulo Research Foundation FAPESP (Grants No.2013/00134–7 and 2017/17872–1), Brazilian National Council for Scientific and Technological Development CNPq (Grant No. 150979/2020-7) and Spanish MICINN (Project MAT2017-88788-R)
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Role of magnetic ordering in the phase coexistence at the structural instability of the multiferroic BiFeO3-PbTiO3

  • Fernández-Posada, Carmen M.
  • Castro, Alicia
  • Pérez del Real, Rafael
  • Algueró, Miguel
  • Amorín, Harvey
[EN] A promising approach for obtaining a large magnetoelectric response at room temperature in single-phase materials is to make use of phase-change phenomena at structural instabilities of a multiferroic state. This is the case of perovskites showing the morphotropic phase boundary (MPB) between ferroelectric polymorphs with differentiated magnetic orderings, like in BiFeO3-PbTiO3. Indeed, distinctive magnetoelectric effects were recently shown in Mn-modified BiFeO3-PbTiO3, associated with the electric field-induced phase transition between the coexisting MPB phases. We report here analogous effects under the magnetic field in 0.7BiFeO3-0.3PbTiO3, which shed light on the reversibility of the phase-change phenomena and the role of the magnetic ordering in the phase coexistence at the structural instability characteristic of the MPB. Results demonstrate magnetic field-driven phase-change phenomena., This work was funded by Spanish MINECO Project No. MAT2017-88788-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Beta phase crystallization and ferro/piezoelectric performances of melt-processed PVDF blends with PMMA copolymers containing ionizable moieties

  • de Neef, Alexandre
  • Samuel, Cédric
  • Amorín, Harvey
  • Stoclet, Gregory
  • Jiménez, Ricardo
  • Dubois, Philippe
  • Soulestin, Jérémie
  • Raquez, Jean-Marie
[EN] Poly(methyl methacrylate-co-methacrylic acid) (PMMA-co-MAA) copolymer containing ionizable moieties is here investigated as a melt processing additive for PVDF to develop high-quality ferro/piezoelectric polymer films by extrusion-calendering. The PVDF/PMMA-co-MAA miscibility and the β-phase crystallization from the melt state at high cooling rates were first explored by Flash DSC. Transposition to the melt-processing of thin films by extrusion-calendering is attempted and a direct production of β-crystals in high amounts is attested at a specific content of 5 wt-% PMMA-co-MAA. Ferro/piezoelectric properties were subsequently investigated and classical ferroelectric-type hysteresis loops clearly appear at room temperature for AC electric fields higher than 900 – 1200 kV/cm. Enhanced remanent polarizations (P) are observed with only 5 wt-% PMMA-based additives and the best ferroelectric performances are identified for PVDF/PMMA-co-MAA blends, in agreement with a higher β-phase content. Stable piezoelectric properties are also highlighted with maximal piezoelectric coefficient (d) of 11 pC/N for these formulations. A linear relationship is found between d and P in accordance with several models and, in this respect, the origin/optimization of the remanent polarization was investigated. Crystal transformations are revealed during high-voltage AC poling and high-quality ferroelectric behaviors with high P values up to 7 µC/cm are obtained at elevated poling temperatures for PVDF/PMMA-co-MAA blends (theoretical d up to 16 pC/N) approaching the theoretical limit value for perfectly-poled β-crystals. This study clearly opens up interesting perspectives in the development of cost-effective electroactive polymer films using industrially-relevant processes and demonstrates that PVDF-based blends with miscible functional PMMA copolymers represent an interesting approach for this purpose., Authors gratefully acknowledge the Wallonia Region/Service Public de Wallonie (Belgium), West Vlaanderen Region (Belgium), Agentschap Innoveren Ondernemen (Belgium) and European Commission (FEDER) for the financial support in the framework of the INTERREG V FWVL program (BIOHARV project, GoToS3 portofolio). Authors particularly thank Samuel Devisme from Arkema (France) for supplying raw materials. UMons (LPCM) gratefully acknowledges the Belgian Federal Government Office of Science Policy/Belgian Federal Science Policy Office (SSTC – PAI 6/27, Belgium) for general support and is much indebted to both the Wallonia Region/Service Public de Wallonie (Belgium) and the European Commission (FEDER) for financial support in the frame of phasing-out Hainaut. IMT Lille Douai and Université de Lille acknowledge both the International Campus on Safety and Intermodality in Transportation (CISIT, France), the Hauts-de-France Region (France) and the European Commission (FEDER) for their contributions to funding extrusion equipments, SAXS-WAXS laboratory equipments and calorimetric characterization tools. Authors also thanks the Spanish Ministerio de Economía y Competitividad (MINECO) for financial supports of MAT2017-88788-R and MAT2016-76851-R projects.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Direct epitaxial growth of polar Hf0.5Zr0.5O2 films on corundum

  • Barriuso, Eduardo
  • Koutsogiannis, Panagiotis
  • Serrate, David
  • Herrero Martín, Javier
  • Jiménez, Ricardo
  • Magén, César
  • Algueró, Miguel
  • Algarabel, Pedro A.
  • Pardo, José A.
This article belongs to the Special Issue Pulsed Laser Deposited Nanostructures., Single-phase epitaxial Hf0.5Zr0.5O2 films with non-centrosymmetric orthorhombic structure have been grown directly on electrode-free corundum (α-Al2O3) substrates by pulsed laser deposition. A combination of high-resolution X-ray diffraction and X-ray absorption spectroscopy confirms the epitaxial growth of high-quality films belonging to the Pca21 space group, with [111] out-of-plane orientation. The surface of a 7-nm-thick sample exhibits an atomic step-terrace structure with a corrugation of the order of one atomic layer, as proved by atomic force microscopy. Scanning transmission electron microscopy reveals that it consists of grains with around 10 nm lateral size. The polar nature of this film has been corroborated by pyroelectric measurements. These results shed light on the mechanisms of the epitaxial stabilization of the ferroelectric phase of hafnia., We acknowledge the research projects MAT2017-88788-R, PID2019-107338RB-C64, and PID2020-112914RB-I00, funded by MCIN/AEI/10.13039/501100011033. This work has received funding from regional Gobierno de Aragón through projects E28_20R and E12_20R, including FEDER funding, and from the EU’s Horizon 2020 programme under the grant agreement No. 823717-ESTEEM3 and the Marie Skłodowska-Curie grant agreement No. 861153-MANIC., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Solution processing of morphotropic phase boundary BiFeO3-PbTiO3 thin films with reduced conductivity for high room temperature switchable polarization

  • Zia, Layiq
  • Jaffari, G. Hassnain
  • Jiménez, Ricardo
  • Bretos, Íñigo
  • Amorín, Harvey
  • Algueró, Miguel
  • Rodríguez-Castellón, Enrique
  • Calzada, M. L.
[EN] The (1 – x)BiFeO-xPbTiO (BFO-PTO) perovskite solid solution has great potential for being used in practical devices, as it exhibits significant ferroelectric response at its morphotropic phase boundary (MPB). However, the significant conduction, particularly high electrical leakage currents that BFO-PTO films show at room temperature, deteriorates their functionality. This is mainly associated with the presence of multivalent iron along with A-site and oxygen vacancies. Here, solution-derived BFO-PTO thin films have been crystallized at low temperature on Pt/TiO/SiO/Si substrates, by a rapid thermal annealing process to minimize Bi and Pb volatilization. X-ray analyses have revealed that textured films are obtained with a pseudocubic perovskite structure and without the formation of detectable second phases. Microstructural studies indicated a columnar growth of the films with grain size well above the nanometric range, which, therefore, should not produce an appreciable reduction of the ferroelectric response due to size effects. Because of the relatively low content of charged defects produced in these BFO-PTO films during processing, ferroelectric hysteresis loops can be measured at room temperature. The highest value of remnant polarizations (2P= 58 μC/cm) was obtained for the 0.65BiFeO-0.35PbTiO (65BFO-35PTO) films, which suggests that this film composition lies in the proximity of the MPB where the coexistence of a highly textured <100> tetragonal phase and a rhombohedral one seems to occur., Layiq Zia acknowledges the Higher Education Commission of Pakistan (HEC) for financial support for his stay at ICMM-CSIC under the Indigenous 5000-PhD Fellowship Program (PIN: 112-27186-2PS1-143) and the International Research Support Initiative Program (IRSIP) (PIN: IRSIP 43 PSc 48). Ricardo Jiménez, Iñigo Bretos, Harvey Amorín, Miguel Algueró, and M. Lourdes Calzada acknowledge the financial support of the Spanish Projects PID2019-104732RB-I00, MAT2017-88788-R, and MAT2017-91772-EXP. Iñigo Bretos acknowledges financial support from the Ramón & Cajal Spanish Program. GHJ acknowledges financial support from the Pakistan Higher Education Commission (HEC, NRPU project number 8342). Enrique Rodríguez-Castellón thanks project RTI2018-099668-BC22 of Ministerio de Ciencia, Innovación y Universidades, and FEDER funds.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Lead-free Ba0.85Ca0.15Zr0.1Ti0.9O3 ferroelectric ceramics with refined microstructure and high strain under electric field by mechanosynthesis

  • Amorín, Harvey
  • Venet, Michel
  • Chinarro Martín, Eva
  • Ramos, Pablo
  • Algueró, Miguel
  • Castro, Alicia
Lead-free ferroelectric Ba0.85Ca0.15Zr0.1Ti0.9O3 stands out among environmentally friendly alternatives to commercial Pb(Zr,Ti)O3 piezoceramics for its large piezoelectric coefficients, and it is especially suitable for applications in which thermal depoling is not an issue like bio-implanted devices. However, ceramic processing by conventional means consistently results in exaggerated grain growth, which compromises reliability and has prevented its transfer to industry. We report here the application of high-energy milling for the mechanosynthesis of nanocrystalline Ba0.85Ca0.15Zr0.1Ti0.9O3 powders with enhanced reactivity, and to the control of grain growth during ceramic processing to obtain materials with tailored microstructures and decreasing grain sizes down to the sub-10 µm range. Characterization of the electrical and electromechanical properties was accomplished and uncovered triggering of a new mechanism for very large strain under electric field in fine-grained ceramics. Process optimization by precursor selection and preliminary up-scaling studies are also presented., Funded by the Spanish MINECO Project MAT2017-88788-R. M. Venet thanks financial support by São Paulo Research Foundation FAPESP (grant number 2017/17872-1)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Coexisting magnetic orders and concomitant Morin-like transition and relaxor behavior in multiferroic Aurivillius Bi4Ti3 - 2xNbxFexO12compounds

  • Algueró, Miguel
  • Pérez del Real, Rafael
  • Amorín, Harvey
  • Castro, Alicia
[EN] Aurivillius layered oxides with general formula (Bi2O2)(Am-1BmO3m+1) stand out among room-temperature magnetoelectric multiferroics for their large magnetization. However, despite extensive research, there is an obvious lack of understanding of their magnetism. The chemical design strategy for obtaining multiferroism involves the incorporation of M3+ magnetic cations at the B-site of well-known ferroelectric compounds such as Bi4Ti3O12 (m = 3). We report here a study of the magnetism and dielectric properties of Aurivillius Bi4Ti3 - 2xNbxFexO12 phases with x ≥ 1 up to 1.2, which correspond to magnetic cation fractions at the B site between 0.33 and 0.4 above the threshold for percolation. This is a three-layer system, less prone to the formation of intergrowths, which nominally contains Fe3+ as single magnetic species. Despite that, a rich phenomenology is uncovered. Coexisting magnetic orders are present in the Aurivillius compounds, and a Morin-like transition takes place at low temperatures. The dielectric characterization does not show any associated anomaly that could indicate a polymorphic phase transition but the appearance of relaxor-like characteristics. Possible scenarios are discussed, which involve the presence of Fe2+, cation partitioning between nonequivalent B-sites, and the development of polar nanodomains within a ferroelectric phase at a spin reorientation transition., Research funded by Spanish MICINN through Project No. MAT2017-88788-R. Technical support by Ms. I. Martínez at ICMM-CSIC was also recognized. Part of the FEG-SEM experiments were carried out as service from the MiNa Laboratory at IMN, which acknowledges funding from CM (Project No. S2018/NMT-4291 TEC2SPACE), MINECO (Project No. CSIC13-4E-1794), and EU (FEDER, FSE), Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Multiferroic Aurivillius Bi4Ti2-xMnxFe0.5Nb0.5O12 (n=3) compounds with tailored magnetic interactions

  • Algueró, Miguel
  • Sanz-Mateo, Jorge
  • Pérez del Real, Rafael
  • Ricote, J.
  • Fernández-Posada, Carmen M.
  • Castro, Alicia
[EN] Aurivillius compounds with the general formula (Bi2O2)(A(n-1)B(n)O(3n+1)) are a highly topical family of functional layered oxides currently under investigation for room-temperature multiferroism. A chemical design strategy is the incorporation of magnetically active BiMO3 units (M: Fe3+, Mn3+, Co3+ horizontal ellipsis ) into the pseudo-perovskite layer of known ferroelectrics like Bi4Ti3O12, introducing additional oxygen octahedra. Alternatively, one can try to directly substitute magnetic species for Ti4+ in the perovskite slab. Previous reports explored the introduction of the M3+ species, which required the simultaneous incorporation of a 5+ cation, as for the Bi4Ti3-2xNbxFexO12 system. A larger magnetic fraction might be attained if Ti4+ is substituted with Mn4+, though it has been argued that the small ionic radius prevents its incorporation into the pseudo-perovskite layer. We report here the mechanosynthesis of Aurivillius Bi4Ti2-xMnxNb0.5Fe0.5O12 (n = 3) compounds with increasing Mn4+ content up to x = 0.5, which corresponds to a magnetic fraction of 1/3 at the B-site surpassing the threshold for percolation, and equal amounts of Mn4+ and Fe3+. The appearance of ferromagnetic superexchange interactions and magnetic ordering was anticipated and is shown for phases with x >= 0.3. Ceramic processing was accomplished by spark plasma sintering, which enabled electrical measurements that demonstrated ferroelectricity for all Mn4+-containing Aurivillius compounds. This is a new family of layered oxides and a promising alternative single-phase approach for multiferroism., Spanish MICINN through the project MAT2017-88788-R. The XPS system at Cambridge is part of the Sir Henry Royce Institute – Cambridge Equipment, EPSRC grant EP/P024947/1. Technical support by Ms I. Martínez, at ICMM-CSIC is also acknowledged.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Solvent-Free Design of Biobased Non-isocyanate Polyurethanes with Ferroelectric Properties

  • Sessini, Valentina
  • Thai, Cuong Nguyen
  • Amorín, Harvey
  • Jiménez, Ricardo
  • Samuel, Cédric
  • Caillol, Sylvain
  • Cornil, Jérôme
  • Hoyas, Sébastien
  • Barrau, Sophie
  • Dubois, Philippe
  • Leclère, Philippe
  • Raquez, Jean-Marie
[EN] Increasing energy autonomy and lowering dependence on lithium-based batteries are more and more appealing to meet our current and future needs of energy-demanding applications such as data acquisition, storage, and communication. In this respect, energy harvesting solutions from ambient sources represent a relevant solution by unravelling these challenges and giving access to an unlimited source of portable/renewable energy. Despite more than five decades of intensive study, most of these energy harvesting solutions are exclusively designed from ferroelectric ceramics such as Pb(Zr,Ti)O3 and/or ferroelectric polymers such as polyvinylidene fluoride and its related copolymers, but the large implementation of these piezoelectric materials into these technologies is environmentally problematic, related with elevated toxicity and poor recyclability. In this work, we reveal that fully biobased non-isocyanate polyurethane-based materials could afford a sustainable platform to produce piezoelectric materials of high interest. Interestingly, these non-isocyanate polyurethanes (NIPUs) with ferroelectric properties could be successfully synthesized using a solvent-free reactive extrusion process on the basis of an aminolysis reaction between resorcinol bis-carbonate and different diamine extension agents. Structure-property relationships were established, indicating that the ferroelectric behavior of these NIPUs depends on the nanophase separation inside these materials. These promising results indicate a significant potential for fulfilling the requirements of basic connected sensors equipped with low-power communication technologies., Spanish Ministerio de Economía y Competitividad (MINECO) forfinancial support through projects MAT2017-88788-R and MAT2016-76851-R. This project has received funding from European Union’s Horizon 2020 research and innovation programmeunder the Marie Skłodowska-Curie grant agreement no.955700.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Magnetoelectric properties of CoFe2O4/BNT–BT0.08 biphasic nanocomposites, with 0–3 connectivity, prepared by sol-gel method

  • Cernea, Marin
  • Radu, Roxana
  • Amorín, Harvey
  • Vasile, Bogdan Stefan
  • Surdu, Vasile Adrian
  • Trusca, Roxana
  • Gavrila, Raluca
  • Galassi, Carmen
[EN] Motivated by the goal of developing ultralow power, smart and multifunctional nano (micro) electronic devices, research has shown unwavering interest in synthesis methods, architectures and interphase connectivity of composites containing magnetostrictive and piezoelectric phases, known as magnetoelectric (ME) materials. Herein we report on CoFeO/BiNaTiO–BaTiO biphasic ME composites, obtained by sol-gel chemistry, by mixing the precursor sols of the two phases into one precursor sol and further transforming it into gel, with the goal of obtaining homogeneous nanocomposites with magnetoelectric properties. The structural properties, the temperature dependance of dielectric properties, the magnetic and magnetoelectric properties of these biphasic mixtures, with various molar ratios CoFeO/BNT–BT = 0.5:1, 1:1 and 1.5:1, are investigated. It is observed that the amount of CoFeO and the synthesis in situ of these composites influences their macroscopic properties showing a high difficulty of carrying out an efficient poling resulting in small piezoelectric and magnetoelectric response. It was concluded that the synthesis procedure, the type of architecture and the interphase connectivity are of outmost importance for magnetoelectric properties based on lead-free materials., The authors gratefully acknowledge the financial support from Core Program PN19-0.3 (Contract No. 21N/08.02.2019) from the Romanian Ministry of Research. H. Amorín acknowledges financial support from Spanish MINECO projects MAT2017-88788-R and PID2021-122708OB-C33, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Microstructure-property relationships in composites of 8YSZ ceramics and in situ graphitized nanocellulose

  • Hudelja, Polona
  • Schmidt, Rainer
  • Amorín, Harvey
  • Drev, Sandra
  • Iveković, Aljaž
  • Abram, Anže
  • Kocjan, Andraž
  • Wicklein, Bernd
Ceramic matrix composites (CMC) of 8 mol.% yttria-stabilized zirconia (8YSZ) mixed with natural fiber nanocellulose (0.75, 1, 2 wt%) were prepared by spark plasma sintering (SPS). Nanocellulose markedly improved the densification of the 8YSZ ceramic matrix and induced significant grain size refinement. It was demonstrated that in situ graphitization of nanocellulose during the SPS processing resulted in 6 nm thin turbostratic graphite layers homogeneously covering the 8YSZ ceramic grains. The dielectric properties were analyzed by electrical impedance spectroscopy suggesting a low percolation threshold near or below ≈ 1.6 vol% graphite, above which mixed ionic-electronic conduction dominates. The CMCs are stable under reducing conditions (5%H2/Ar atmosphere) at least until 800 °C with a high conductivity of σdc = 0.17 S∙cm−1 even at 900 °C (8YSZ-2%CNF). These features make the 8YSZ-nanocellulose CMCs promising candidates for application in medium- to high-temperature electrochemical devices. © 2022, PH thanks the JECS Trust for funding a mobility stay project in 2020 (Contract 2019231). The Slovenian Research Agency is acknowledged for funding through research program P2-0087. RS acknowledges funding from the EU FLAG-ERA project To2Dox (JTC-2019-009) and the Spanish MINECO (Grant PID2020-118078RB-I00). Financial support from the Agencia Estatal de Investigación (AEI, Spain) and the FEDER Program (EU) is acknowledged (MAT2015-71117-R). BW thanks the MICINN for a JIN contract (PID2019-107022RJ-I00). HA thanks the MICINN for funding through project MAT2017-88788-R., Supplementary data associated with this article can be found in the online version at doi:10.1016/j.jeurceramsoc.2022.04.041, Peer reviewed
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Direct epitaxial growth of polar Hf0.5 Zr0.5 O2 films on corundum

  • Barriuso, E.
  • Koutsogiannis, P.
  • Serrate, D.
  • Herrero-Martín, J.
  • Jiménez, R.
  • Magén, C.
  • Algueró, M.
  • Algarabel, P. A.
  • Pardo, J. A.
Single-phase epitaxial Hf0.5 Zr0.5 O2 films with non-centrosymmetric orthorhombic structure have been grown directly on electrode-free corundum (a-Al2 O3) substrates by pulsed laser deposition. A combination of high-resolution X-ray diffraction and X-ray absorption spectroscopy confirms the epitaxial growth of high-quality films belonging to the Pca21 space group, with 111] out-of-plane orientation. The surface of a 7-nm-thick sample exhibits an atomic step-terrace structure with a corrugation of the order of one atomic layer, as proved by atomic force microscopy. Scanning transmission electron microscopy reveals that it consists of grains with around 10 nm lateral size. The polar nature of this film has been corroborated by pyroelectric measurements. These results shed light on the mechanisms of the epitaxial stabilization of the ferroelectric phase of hafnia. © 2022 by the authors. Licensee MDPI, Basel, Switzerland.