Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 65
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Enhancing ultrasonic-assisted drying of low-porosity products through pulsed electric field (PEF) pretreatment: The case of butternut squash

  • Llavata-Cabrero, Beatriz
  • Rosselló, C.
  • Quiles Chuliá, Mª Desamparados|||0000-0003-4991-6629
  • Carcel, J. A.|||0000-0002-3796-6146
[EN] Ultrasonic-assisted drying is an effective technique for accelerating drying processes, particularly for products with high porosity. The structural changes induced by pulsed electric field (PEF) treatment can make lowporosity products more susceptible to the effects of ultrasound during drying. This study aimed to investigate the influence of PEF treatment on the structure of low-porosity products, such as butternut squash, and to evaluate its effect on ultrasonic-assisted drying. PEF pretreatment altered the physicochemical and microstructural properties of butternut squash. Thus, the higher the energy input, the higher the cell disintegration rate, the lower the shearing force and the lower the water holding capacity. For the same energy input applied, no influence was observed from the different combinations of pulse number and electric field intensity used. The microstructural analysis also showed greater effects with increasing intensity of PEF treatments. All these changes affected the subsequent drying, increasing the drying rate of conventional drying. Moreover, PEF pretreatment enhanced the ultrasound effects when applied during drying, reducing drying time by up to 47% when moderate PEF intensity was used. Therefore, PEF pretreatment under the appropriate conditions could make ultrasound-assisted drying of low-porosity products, such as butternut squash, more feasible., This work was supported by the PID2019-106148RRC42 grants funded by MCIN/AEI/10.13039/501100011033; the PID2022-136889OB-C21 and PID2022-136889OB-C22 grant funded by MCIN/AEI/10.13039/501100011033 and by ERDF/EU, and the PhD grant of Beatriz Llavata from the Universitat Politecnica de Valencia (PAID-01-19).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A study of the early life of Gasoline Particulate Filters: reactive and dissipative acoustic effects

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • De La Morena, Joaquín|||0000-0003-0208-508X
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Redondo-Navarro, Álvaro Rafael|||0000-0003-1668-1245
  • Servetto, Emanuele
[EN] The presence of after-treatment systems (ATS) has some side effects as they modify the wave dynamics, back-pressure and acoustic behavior of the exhaust system, that define the boundary conditions for the main silencing device. Gasoline particulate filters (GPF) have a considerable influence on these traits as their working principle depends on wall-flow monoliths; additionally, particulate filters have an inherent transient behavior due to the loading-regeneration cycles during their operation. In this paper, the steady and unsteady behavior of a typical device containing a three-way catalyst (TWC) and a GPF has been characterized in "new" (prior to any use) and "used" (after regeneration) conditions, with special focus on the role of dissipation. Pressure drop measurements were used in steady flow, whereas an acoustic energy balance was performed in the unsteady case that allows for the identification of the reactive and dissipative contributions. The results obtained for the GPF suggest that after it has been used for a relatively short time it oscillates between a maximum and a minimum loading over load¿regeneration cycles burning the soot, never reaching back brand¿new cleanness due to accumulation into the substrate pores and only suffering from ash accumulation over very long times. The results were then used to analyze the ability of a standard gas-dynamic code to reproduce the influence of the loading on the reactive and dissipative effects observed, with the main conclusion that by properly tuning the model parameters it is possible to reproduce, at least qualitatively, the trends observed in the experiments. The model can thus be used to provide adequate inlet conditions for the design of the exhaust line., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: A lvaro Redondo is supported by Universitat Politecnica de Valencia through the Programa de Ayudas de Investigacion y Desarrollo [PAID-01-19] which grants his predoctoral contract.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A Type II singularity avoidance algorithm for parallel manipulators using output twist screws

  • Pulloquinga-Zapata, José
  • Escarabajal-Sánchez, Rafael José
  • Valera Fernández, Ángel|||0000-0001-6843-6394
  • Vallés Miquel, Marina|||0000-0002-6396-0098
  • Mata Amela, Vicente|||0000-0003-2255-0567
[EN] Parallel robots (PRs) are closed-chain manipulators with diverse applications due to their accuracy and high payload. However, there are configurations within the workspace named Type II singularities where the PRs lose control of the end-effector movements. Type II singularities are a problem for applications where complete control of the end-effector is essential. Trajectory planning produces accurate movements of a PR by avoiding Type II singularities. Generally, singularity avoidance is achieved by optimising a geometrical path with a velocity profile considering singular configurations as obstacles. This research presents an algorithm that avoids Type II singularities by modifying the trajectory of a subset of the actuators. The subset of actuators represents the limbs responsible for a Type II singularity, and they are identified by the angle between two Output Twist Screws. The proposed avoidance algorithm does not require optimisation procedures, which reduces the computational cost for offline trajectory planning and makes it suitable for online trajectory planning. The avoidance algorithm is implemented in offline trajectory planning for a pick and place planar PR and a spatial knee rehabilitation PR., Acknowledgements This research was partially funded by Fondo Europeo de Desarrollo Regional (PID2021-125694OB-I00) , cofounded by Vicer-rectorado de Investigacion de la Universitat Politecnica de Valencia (PAID-11-21) and by Programa de Ayudas de Investigacion y Desarrollo de la Universitat Politecnica de Valencia (PAID-01-19) . Funding for open access charge: CRUE-Universitat Politecnica de Valencia. Moreover, the authors would like to thank the help of all anonymous reviewers, which have improved the paper's readability.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

Performance y documentación: propuesta de un modelo para la adquisición y conservación de obra performativa

  • Fernández-Valdés, Paula
  • Cuesta, Salomé|||0000-0002-7898-8093
[ES] En un mundo que tiende exponencialmente hacia la transformación digital y la desobjetualización, encontramos que en el ámbito de la cultura se producen cada vez más experiencias en torno a lo virtual, lo intangible y lo inmaterial. Estos fenómenos, activados por la convergencia entre nuevas tecnologías y producción artística, generan complejas obras performativas que afectan a los protocolos propios del campo de la conservación y la restauración. La complejidad de trabajar con estas tipologías es especial, ya que son piezas que se caracterizan por estar basadas en el tiempo, ser efímeras, vivas y dinámicas. ¿Se puede conservar una acción? ¿La audiencia participa en la obra? ¿Necesita ser documentada? A partir del estudio de los protocolos de conservación de los considerados nuevos medios, desarrollaremos un modelo conceptual con el objetivo de abordar la complejidad de las obras performativas y reflexionar sobre posibles modelos para su preservación.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Genetic Dissection of ToLCNDV Resistance in Resistant Sources of Cucumis melo

  • Pérez-Moro, Clara
  • Sáez, Cristina
  • Dhillon, Narinder P. S.
  • Sifres Cuerda, Alicia Gemma|||0000-0002-9498-0083
  • López Del Rincón, Carmelo|||0000-0001-7459-1315
  • Picó Sirvent, María Belén|||0000-0001-7761-990X
  • Pérez De Castro, Ana María|||0000-0002-4949-3323
[EN] Tomato leaf curl New Delhi virus (ToLCNDV) is a begomovirus causing significant melon (Cucumis melo) crop losses globally. This study aims to map the ToLCNDV resistance in the PI 414723 melon accession, previously identified and characterized through phenotypic studies, thereby exploring shared genomic regions with the established resistant source WM-7. In the present study, WM-7 and PI 414723 were crossed with the susceptible accessions 'Rochet' and 'Blanco' respectively, to generate F-1 hybrids. These hybrids were self-pollinated to generate the populations for mapping the ToLCNDV resistance region and designing markers for marker-assisted selection. Disease evaluation included visual symptom scoring, viral-load quantification and tissue printing. Genotyping-by-sequencing and SNP markers were used for quantitative trait loci (QTL) mapping. For genetic analysis, qPCR and bulked segregant RNA-seq (BSR-seq) were performed. Gene expression was assessed using RNA-seq, and qRT-PCR was used for confirmation. The research narrows the candidate region for resistance in WM-7 and identifies overlapping QTLs on chromosome 11 in PI 414723, found in the region of the DNA primase large subunit. BSR-seq and expression analyses highlight potential regulatory roles of chromosome 2 in conferring resistance. Differential expression was confirmed for six genes in the candidate region on chromosome 2. This study confirms the existence of common resistance genes in PI 414723 and WM-7., This work was supported by the grant PID2021-125787OR-C33, funded by MICIU/AEI/10.13039/501100011033; the 'FEDER UE' PROMETEO/2021/072 project for excellence groups Conselleria d'Educacio, Cultura, Universitats i Ocupacio (Generalitat Valenciana, Spain); and project RTC-2017-6023-2, funded MICIU/AEI/10.13039/501100011033 and by FEDER 'A way of making Europe'. C.S. was the recipient of a 'Margarita Salas' grant (MS/60) from the Requalification Program for Excellence of the Universitat Politecnica de Valencia, Spanish Ministry of Universities and European Union-Next Generation EU. C.P.M. is a recipient of the predoctoral fellowship "Programa de Ayudas de Investigacion y Desarrollo (PAID-01-19)" from Universitat Politecnica de Valencia. Funding for open access charge: Universitat Politecnica de Valencia (PAID-12-23).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Water-assisted synthesis of stable and multicolored CsPbX3@SiO2 core shell nanoparticles as fluorescent probes for biosensing

  • Collantes-Pablo, Cynthia
  • Teixeira, William|||0000-0002-6729-9508
  • González-Pedro, Victoria|||0000-0002-8133-5958
  • Bañuls Polo, María-José|||0000-0002-2422-7731
  • Quintero-Campos, Pedro|||0000-0002-9398-5077
  • Morais, Sergi|||0000-0002-3722-2358
  • Maquieira, Angel|||0000-0003-4641-4957
[EN] Colloidal lead halide perovskite nanocrystals are highly luminescent materials with great promise as fluorescent probes in biosensing as long as their intrinsic instability in aqueous media is effectively addressed. In this study, we successfully prepared stable and multicolored CsPbX3@SiO2 (X = Cl/Br, Br and I) core¿ shell nanoparticles through a simple method based on the water-induced transformation of Cs4PbX6 into CsPbX3, combined with sol¿gel procedures. We observed that the concentration of the Cs4PbX6 precursor plays a crucial role in the formation of isolated nanospheres with uniform silica coating and in controlling the number of core-free particles. Furthermore, our research expands this approach to other halide compositions, resulting in multicolored core¿shell nanoparticles with emission wavelengths ranging from 490 to 700 nm, average sizes below 30 nm, and photoluminescence quantum yields close to 60%. Unlike in previous reports, the silica coating boosts the photoluminescence quantum yields compared to uncoated counterparts and provides increased structural stability for more than four days. Moreover, a controlled thermal treatment confers water stability to the as-synthesized nanoparticles. To establish the feasibility of the developed materials as fluorescent probes, we successfully demonstrated their specific recognition of a humanized antibody (omalizumab) used in treating patients with severe allergic asthma. This work paves the way to develop in vitro tests using CsPbX3@SiO2 core¿shell nanoparticles as fluorogenic probes., This work was financially supported by the E.U FEDER project ADBIHOL/AEI/10.13039/501100011033 from MCIN/AEI and PROMETEO/2020/094 from Generalitat Valenciana. C. C. thanks the Spanish Ministry of Economy and Competitiveness for her predoctoral contract (BES-2017-080242). W. T. acknowledges the financial support from Universitat Politécnica de Valéncia for the Ph.D. studies (PAID-01-19-06).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and Characterization of Polyester and Acrylate-Based Composites with Hydroxyapatite and Halloysite Nanotubes for Medical Applications

  • Torres, Elena
  • Domínguez-Candela, Iván|||0000-0003-3288-1079
  • Castelló-Palacios, Sergio|||0000-0003-4689-652X
  • Vallés Lluch, Ana|||0000-0002-7896-8666
  • Fombuena, Vicent|||0000-0001-7266-6205
[EN] We aimed to study the distribution of hydroxyapatite (HA) and halloysite nanotubes (HNTs) as fillers and their influence on the hydrophobic character of conventional polymers used in the biomedical field. The hydrophobic polyester poly (¿-caprolactone) (PCL) was blended with its more hydrophilic counterpart poly (lactic acid) (PLA) and the hydrophilic acrylate poly (2-hydroxyethyl methacrylate) (PHEMA) was analogously compared to poly (ethyl methacrylate) (PEMA) and its copolymer. The addition of HA and HNTs clearly improve surface wettability in neat samples (PCL and PHEMA), but not that of the corresponding binary blends. Energy-dispersive X-ray spectroscopy mapping analyses show a homogenous distribution of HA with appropriate Ca/P ratios between 1.3 and 2, even on samples that were incubated for seven days in simulated body fluid, with the exception of PHEMA, which is excessively hydrophilic to promote the deposition of salts on its surface. HNTs promote large aggregates on more hydrophilic polymers. The degradation process of the biodegradable polyester PCL blended with PLA, and the addition of HA and HNTs, provide hydrophilic units and decrease the overall crystallinity of PCL. Consequently, after 12 weeks of incubation in phosphate buffered saline the mass loss increases up to 48% and mechanical properties decrease above 60% compared with the PCL/PLA blend., Dominguez-Candela thanks the Universitat Politècnica de València for the financial support through an FPI-UPV grant (PAID-01-19)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Novel compatibilizers and plasticizers developed from epoxidized and maleinized chia oil in composites based on PLA and chia seed flour

  • Domínguez-Candela, Iván|||0000-0003-3288-1079
  • Gómez-Caturla, Jaume|||0000-0001-8680-4509
  • Cardona, S. C.|||0000-0002-2882-3098
  • Lora-García, Jaime|||0000-0003-1699-5404
  • Fombuena, Vicent|||0000-0001-7266-6205
[EN] Novel compatibilizers and plasticizers derived from epoxidized chia seed oil (ECO) and maleinized chia seed oil (MCO) have been applied in composites based on poly(lactic acid) (PLA) and 15 wt% chia seed flour (CSF). Results obtained have been compared to conventional silane coupling agent, (3-glycidyloxypropyl) trimethoxysilane (GPS), and a petroleum-based compatibilizer, poly(styrene-co-glycidyl methacrylate) copolymer (Xibond, (R)). The compatibilization effect of green composites were assessed by FTIR. The addition of all four compatibilizers improved the ductile mechanical and thermal properties of the composites. The morphology analysis revealed an improvement of interfacial adhesion of the CSF particles into the PLA matrix. In particular, ECO and MCO composites showed a roughness with long filaments in their morphology which plays a crucial role in improving the ductile properties highly. The elongation at break was 10 and 8 times higher using ECO and MCO, respectively, compared to uncompatibilized composite. Moreover, the composites manufactured showed low values (<9%) in the water uptake assay and a negligible compostability delay. The use of novel compatibilizers based on modified vegetable oils could mean an interesting proposal to obtain an entirely environmentally friendly composite with a remarkable ductile property., This research work was funded by the Ministry of Science and Innovation-¿Retos de la Sociedad¿. Project references: PID2020-119142RA-I00. I. Dominguez-Candela wants to thank Universitat Politècnica de València for his FPI grant (PAID-2019-SP20190013) and Generalitat Valenciana-GVA (ACIF/2020/233). J. Gomez-Caturla wants to thank Generalitat Valenciana-GVA, for his FPI grant (ACIF/2021/185) and grant FPU20/01732 funded by MCIN/AEI/10.13039/ 501100011033.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Exploring essential variables for successful and unsuccessful football teams in the &quot, Big Five&quot, with multivariate supervised techniques

  • Malagón-Selma, María del Pilar
  • Debón, A.|||0000-0002-5116-289X
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] This research proposes multivariate techniques for discovering the game actions that contribute to the final ranking of football teams. This study uses data from the "Big Five" teams that competed in the Bundesliga First Division, Premier League, LaLiga, Ligue 1, and Serie A in the 2018-2019 season. The principal component analysis is used for outlier detection and for providing an overall preliminary insight. The statistically significant game actions of the top and bottom teams were studied using three supervised multivariate techniques, namely the partial least squares discriminant analysis, random forest and logistic regression. The partial least squares discriminant analysis model best identifies the variables with the most statistically significant contribution to a team's success or failure. The results were compared with those obtained using two-sample univariate tests (such as the Student's t-test or the Mann-Whitney test), demonstrating the advantages of multivariate approaches over univariate approaches. The results indicate that the top teams have both offensive and defensive power, and emphasise the high number of attacking actions; in contrast, the bottom teams have weak defences and few offensive actions., The authors want to express their gratitude to the Universitat Politecnica de Valencia for the financial support through the FPI-UPV grant (PAID-01-19).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Study Of Spray-Air Interaction In A Gasoline Fuel Injection System Under Various Flash Boiling Conditions

  • Mendoza Álvarez, Víctor Daniel
[ES] La inyección de combustible en sistemas de combustión, particularmente de gasolina, sigue desempeñando un papel importante en la industria automotriz y en la investigación actual dado su potencial para lograr una alta eficiencia con bajas emisiones. En este contexto, el presente estudio tiene como objetivo profundizar en la comprensión de los fenómenos clave que afectan la inyección y la atomización del chorro. Esta investigación analiza dos inyectores GDI, ambos capaces de operar a altas presiones de inyección. Uno sirve como referencia principal para la caracterización, mientras que el segundo se utiliza con fines comparativos y para la validación de las tendencias observadas. Se emplean dos combustibles para simular diferentes propiedades de volatilidad de los compuestos de la gasolina y reproducir condiciones de flashing más extremas, así como Etanol, un alcohol representativo usualmente considerado en estrategias de bajas emisiones de carbono. Se llevó a cabo una metodología exhaustiva para medidas de chorro GDI mediante PDPA usando un equipo nuevo en el centro de investigación que albergó este proyecto, el Clean Mobility and Thermofluids (CMT). Además, se mejoró el control de la temperatura en la maqueta mediante la instalación de un nuevo módulo de resistencias y aislamiento para un calentamiento más rápido y homogéneo del gas ambiente. También se probaron dos ventanas giradas para optimizar la alineación del PDPA. Para el flujo interno, se realiza una caracterización que incluye la tasa de momento (ROM) y la tasa de inyección (ROI) de ambas toberas. La geometría de éstas se midió utilizando varias técnicas, incluidas técnicas ópticas avanzadas de rayos X en el Argonne National Laboratory (ANL). La visualización lateral con dispersión MIE ayudó a tener una idea clara de los fenómenos que tienen lugar durante las inyecciones mientras se realizaban mediciones de tamaño y velocidad de gotas. En este sentido, algunas de las condiciones de flashing más extremas produjeron el fenómeno de colapso del chorro debido la interacción de las plumas. Se observaron diferentes estructuras de colapso, una para colapso transicional y otras para colapsos completos. Los datos de velocidad y tamaño de las gotas en varias posiciones axiales y radiales confirmaron las tendencias esperadas de atomización, particularmente la influencia positiva de la alta presión de inyección, la temperatura ambiente y el flash boiling. Se observó una clara relación inversa entre RP y el tamaño de las gotas en la mayoría de las condiciones de inyección, es decir, los valores más altos de RP generalmente correspondían a Sauter Mean Diameter (SMD) más bajos. Sin embargo, las desviaciones de esta tendencia atribuidas al inicio del colapso del chorro introdujeron gotas más grandes en la distribución. Siguiendo esta línea, un mapeo de los regímenes de colapso, que van desde leves hasta extremos, permitió determinar que los tamaños de gota dentro de la región de colapso eran consistentemente mayores que los del chorro principal y a menudo anulaban los efectos positivos sobre la atomización de la alta presión de inyección o la ebullición instantánea. La metodología experimental demostró ser efectiva para medidas con PDPA en la región central del inyector, incluso en escenarios de colapso extremos. Así pues, se identificó una banda de colapso cerca del centro del inyector. Esta región es rodeada por áreas con velocidades negativas o fenómenos de flujo inverso, revelando que la posición del colapso está fuertemente influenciada por los chorros más energéticos. En general, se espera que estos resultados cualitativos y cuantitativos contribuyan a la investigación chorros GDI con combustibles volátiles, brindando una aplicación novedosa de herramientas de medición establecidas, y que ofrezcan una comprensión más amplia de estos chorros, además de apoyar futuras investigaciones sobre el diseño de inyectores, estrategias de inyección y optimización de la combustión., [CA] La injecció de combustible en sistemes de combustió, particularment de gasolina, continua exercint un paper important en la indústria automotriu i en la investigació actual donat el seu potencial per a aconseguir una alta eficiència amb baixes emissions. En este context, el present estudi té com a objectiu aprofundir en la comprensió dels fenòmens clau que afecten la injecció i l'atomització del doll. Esta investigació analitza dos injectors GDI, els dos capaços d'operar a altes pressions d'injecció. Un servix com a referència principal per a la caracterització, mentres que el segon s'utilitza amb finalitats comparatius i per a la validació de les tendències observades. S'empren dos combustibles per a simular diferents propietats de volatilitat dels compostos de la gasolina i reproduir condicions de flashing més extremes, així com Etanol, un alcohol representatiu usualment considerat en estratègies de baixes emissions de carboni. Es va dur a terme una metodologia exhaustiva per a mesures de doll GDI mitjançant PDPA usant un equip nou en el centre d'investigació que va albergar este projecte, el Clean Mobility and Thermofluids (CMT). A més, es va millorar el control de la temperatura en la maqueta mitjançant la instal·lació d'un nou mòdul de resistències i aïllament per a un calfament més ràpid i homogeni del gas ambient. També es van provar dos finestres girades per a optimitzar l'alineació del PDPA. Per al flux intern, es realitza una caracterització que inclou la taxa de moment (ROM) i la taxa d'injecció (ROI) de les dos toveres. La geometria d'estes es va mesurar utilitzant diverses tècniques, incloses tècniques òptiques avançades de rajos X en el Argonne National Laboratory (ANL). La visualització lateral amb dispersió MIE va ajudar a tindre una idea clara dels fenòmens que tenen lloc durant les injeccions mentres es realitzaven mesuraments de grandària i velocitat de gotes. En este sentit, algunes de les condicions de flashing més extremes van produir el fenomen de col·lapse del doll degut a la interacció de les plomes. Es van observar diferents estructures de col·lapse, una per a col·lapse transicional i altres per a col·lapses complets. Les dades de velocitat i grandària de les gotes en diverses posicions axials i radials van confirmar les tendències esperades d'atomització, particularment la influència positiva de l'alta pressió d'injecció, la temperatura ambient i el flash boiling. Es va observar una clara relació inversa entre RP i la grandària de les gotes en la majoria de les condicions d'injecció, és a dir, els valors més alts de RP generalment corresponien a Sauter Mean Diameter (SMD) més baixos. No obstant això, les desviacions d'esta tendència atribuïdes a l'inici del col·lapse del doll van introduir gotes més grans en la distribució. Seguint esta línia, un mapatge dels règims de col·lapse, que van des de lleus fins a extrems, va permetre determinar que les grandàries de gota dins de la regió de col·lapse eren consistentment majors que els del doll principal i sovint anul·laven els efectes positius sobre l'atomització de l'alta pressió d'injecció o l'ebullició instantània. La metodologia experimental va demostrar ser efectiva per a mesures amb PDPA a la regió central de l'injector, fins i tot en escenaris de col·lapse extrems. Així doncs, es va identificar una banda de col·lapse prop del centre de l'injector. Esta regió és envoltada per àrees amb velocitats negatives o fenòmens de flux invers, revelant que la posició del col·lapse està fortament influenciada pels dolls més energètics. En general, s'espera que estos resultats qualitatius i quantitatius contribuïsquen a la investigació de dolls GDI amb combustibles volàtils, brindant una aplicació nova de ferramentes de mesurament establides, i que oferisquen una comprensió més àmplia d'estos dolls, a més de secundar futures investigacions sobre el disseny d'injectors, estratègies d'injecció i optimització de la combustió., [EN] Fuel injection in combustion systems, particularly gasoline injections, continues to play a significant role in the automotive industry and ongoing research due to its potential for high efficiency while achieving low emission. In this context, the present study aims to deepen the understanding of the key phenomena affecting spray injection and atomization, focusing on both gasoline surrogates and Ethanol. This research analyzes two GDI injectors, both capable of operating at high injection pressures. One serves as the main reference for characterization, while the second is used for comparative purposes and validation of observed trends. Two surrogate fuels are employed to simulate different volatility properties of gasoline compounds and ultimately reproduce more extreme flashing conditions, as well as Ethanol, a representative alcohol increasingly considered in low-carbon fuel strategies. An exhaustive methodology was conducted for employing PDPA on GDI sprays using a new instrumentation at the research center that hosted this project, the Clean Mobility and Thermofluids (CMT). Furthermore, the ambient temperature control in the vessel was improved by installing a new resistor module and isolating parts for faster and homogeneous ambient gas heating. Two custom rotated windows were also tested to optimize PDPA alignment. For the internal flow, a characterization including the rate of momentum (ROM) and rate of injection (ROI) of both nozzles is performed. The nozzles geometry was measured using several techniques, including advanced X-ray optical techniques at the Argonne National Laboratory (ANL). Injector response was tested to typical boundary conditions such as injection and ambient pressure, fuel temperature, etc. Side-view visualization using MIE scattering technique aided in having a clear idea of the phenomena taking place at different injection conditions while performing droplet size and velocity measurements. In this sense, some of the most extreme flashing conditions produced the spray collapse phenomenon due to plumes interaction. Different collapse structures were observed, one for transitional and the other for fully collapsed sprays. Velocity and droplet size data at various axial and radial positions confirmed expected atomization trends, particularly the positive influence of high injection pressure, ambient temperature, and flash boiling. A clear inverse relationship between RP and droplet size across most injection conditions was seen, i.e. the higher RP values generally corresponded to lower Sauter Mean Diameters (SMD). However, deviations from this trend attributed to the onset of spray collapse, introduced larger droplets into the distribution. Following this thread, a complete mapping of collapse regimes, ranging from mild to extreme, allowed to determine that droplet sizes within the collapse region were consistently higher than those in the main spray and often override the positive effects on atomization of high injection pressure or flash boiling. The experimental methodology established here proved effective for measuring droplet velocities and sizes in the central region of the injector, even under extreme collapse scenarios. A collapse band was identified near the core of the injector under various flash boiling conditions. This region was surrounded by areas with negative velocities or reverse flow phenomena; revealing that the collapse position was strongly influenced by the most energetic jets. Overall, these qualitative and quantitative findings are expected to contribute to ongoing research on GDI sprays involving volatile fuels, with novel application of established measurement tools, and offera broader understanding of GDI spray behavior, and support future research on injector design, injection strategies, and combustion optimization., Esta tesis se llevó a cabo en el marco de la ayuda para la Formación de Personal Investigador (FPI) Subprograma 1 (PAID-01-19), financiada por la Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Evaluation of Hygrothermal Behaviour in Heritage Buildings through Sensors, CFD Modelling and IRT

  • Lerma Elvira, Carlos|||0000-0003-0436-3725
  • Garcia-Borràs, Júlia|||0000-0002-5470-0753
  • Mas Tomas, Maria De Los Angeles|||0000-0002-0097-0598
  • Torner-Feltrer, María Eugenia Milagro|||0000-0002-8296-0632
  • Vercher Sanchis, José|||0000-0001-9855-4201
  • Gil Benso, Enrique|||0000-0002-6617-640X
[EN] Architectural heritage, building materials and interior space are highly susceptible to temperature and relative humidity. A better knowledge of the hygrothermal dynamics inside buildings allows an adequate conservation of heritage. This work compares three non-destructive techniques (NDT), such as temperature and relative humidity sensors, finite element simulations (CFD) and thermographic pictures (IRT). The work has made it possible to carry out an assessment of the risk of condensation over a year and to identify affected periods and areas of the building. Sensors and IRT pictures provide real data to validate CFD simulations, facilitating a global analysis of the building. The results provided reflect a great concordance between the NDTs used.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analysis of spray/wall impingement using an ECN single-hole injector and a controlled-temperature wall under realistic engine conditions

  • Peraza, Jesús E
  • Payri, Raul|||0000-0001-7428-5510
  • Gimeno, Jaime|||0000-0003-3317-9994
  • Carvallo-García, César Leonardo|||0000-0003-2297-2225
[EN] Spray¿wall interactions (SWI) directly affect fuel¿air mixture and emissions formation. Therefore, they are considered among the most critical physical processes in engine research nowadays. However, the physics of the wall film formation, propagation, and breakup is not fully understood yet. This work aims to use a thermoregulated steel wall to study the spray¿wall interaction phenomenon and its influence on the macroscopic spray behavior. A single-hole injector known as ``Spray D¿¿ in the Engine Combustion Network was used. n-Dodecane was employed as fuel and the wall has been positioned in four different configurations, varying angle and distance respect to the injector tip. For this work, not only diesel combustion is reproduced in the test rig due to ambient gas engine-like thermodynamic conditions, but wall temperature has been controlled to emulate characteristic values that could be found in the piston of an internal combustion engine. This implies that the spray¿wall heat transfer is simulated and its effects on ignition and spray development can be analyzed. Heat flux was measured by employing high-speed thermocouples fitted in the wall and by the use of an one-dimensional transient wall heat model. Three high speed cameras were simultaneously used to observe the SWI, one for the Schlieren optical technique which allows to study the vapor phase of the spray and to determine the ignition delay, another one to observe the natural luminosity of the flame, and finally, an intensified camera was used to determine the lift-off length by observing the chemiluminescence of the OH*. An interesting finding obtained in this work was a boundary layer formation due to the thermal diffusion that contributes to cool down the spray and to delay the high-temperature chemical reactions. Results show a substantial increment of the heat flux and the wall temperature variation with both ambient temperature and density by increasing the flame temperature and gas entrainment. The exposure to the cold wall affects the ignition delay variation with the injection pressure and the wall distance. It was found that the wall temperature (in the range of tested conditions) did not affect the lift-off length location, Authors would like to acknowledge Caterpillar Inc. for its support and interest in this work. The author C. Carvallo thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2019-S1) which is included within the framework of Programa de Apoyo para la Investigacion.. Desarrollo (PAID-01-19). Finally, the collaboration of Omar Huerta Cornejo and Sergi Soro in the laboratory work and the setup of the hardware is greatly thanked.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Estudio del efecto de la introducción de membranas de ultrafiltración en la línea de aguas de un esquema de tratamiento de aguas residuales convencional sobre la digestión anaerobia del fango

  • Ivailova Petkova, Ivana
[ES] El incremento en la población mundial y el cambio en los hábitos de consumo ha generado un aumento en la generación de aguas residuales con contaminantes cada vez más complejos. En la actualidad, el esquema convencional de tratamiento de aguas residuales en EDAR se basa en el empleo de procesos biológicos aerobios que presentan un elevado consumo energético asociado a la aireación, así como una elevada producción de fangos. Por ese motivo la posibilidad de sustituir los procesos aerobios por procesos anaerobios, que permiten valorizar la materia orgánica contenida en el agua residual en forma de energía, es una alternativa cada vez más contemplada. Sin embargo, la aplicación de procesos anaerobios en la línea de aguas de una EDAR está sujeta a limitaciones asociadas a la baja velocidad de crecimiento de los microorganismos anaerobios y, por tanto, a la necesidad de operar a elevados tiempos de retención celular (TRC). Por ello se plantean otras alternativas que permitan incrementar la cantidad de materia orgánica valorizada mediante procesos anaerobios y, por tanto, mejorar el balance energético de la EDAR. Entre estas alternativas destaca la incorporación de un proceso de filtración por membranas en la línea de aguas. En esta tesis se evalúa el efecto de incorporar un proceso de filtración directa en la línea de aguas de una EDAR sobre el rendimiento del proceso de digestión anaerobia al incluir la corriente de rechazo generada. Se consideran dos ubicaciones diferentes para la filtración en la línea de aguas: tras el decantador primario o tras el pretratamiento. Se centra en el análisis de las características fisicoquímicas de la corriente rechazo generada, su comportamiento en un proceso de digestión anaerobia mesófila operado en régimen semicontinuo bajo distintas condiciones de operación (convencional y con membrana, AnMBR) y sus características de sedimentación. Se evalúan las variaciones que tienen lugar en la población de microorganismos presentes en el digestor anaerobio y se realiza un estudio económico en el que se evalúa el balance energético y los costes de inversión y operación (CAPEX y OPEX) asociados. El análisis fisicoquímico y la evaluación del rendimiento del proceso de digestión anaerobia mesófila ponen de manifiesto su elevado potencial de biometanización de la corriente de rechazo. Se obtienen incrementos mayores al 44 % en el caudal de metano diario producido respecto al esquema de una EDAR convencional independientemente de la ubicación del proceso de filtración. Cuando el proceso se sitúa tras el pretratamiento las características de sedimentación se asemejan a las del fango primario, favoreciendo su espesado por gravedad. La dosificación de coagulante comercial no supone mejoras significativas en las características de sedimentación. Las variaciones observadas en la población de microorganismos anaerobios evidencian que situar el proceso de filtración directa tras el pretratamiento favorece el desarrollo de microorganismos implicados en la hidrólisis y acidogénesis como bacterias de la familia Comamonadaceae y Rhodocyclaceae. La reducción del TRH promueve el crecimiento de archaeas hidrogenotróficas como Methanospirillum y Methanobrevibacter y valores elevados de TRC favorecen el crecimiento de microorganismos que degradan materia orgánica compleja, como Pedosphaeraceae. Se obtiene un incremento del 13,7 % en la energía recuperada al colocar el proceso de filtración directa tras el decantador y un incremento ligeramente mayor, 15,5 %, al colocarlo tras el pretratamiento. Los elevados costes de inversión no pueden ser compensados por el ahorro que se obtiene en los costes de operación. De todas formas, se reduce el consumo energético de la EDAR y, por tanto, las emisiones de CO2 a la atmósfera (hasta 220 tCO2eq·año-1). Por este motivo se debe seguir investigando en la reducción de los costes asociados a las membranas., Este trabajo de investigación se enmarca en el proyecto “Modelización y control para la implementación de la tecnología de membranas en las EDAR actuales para su transformación en Estaciones de Recuperación de Recursos” (CTM2017-86751-C2-2-R-AR), financiado por el Ministerio de Economía, Industria y Competitividad (MINECO). Esta tesis también ha sido financiada a través de un contrato predoctoral concedido por la Universitat Politècnica de València (FPI) (PAID-01-19).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The Pragmatic Function of Translanguaging in a Bilingual Telecollaboration Project

  • Di Sarno-García, Sofia
  • Gimeno-Sanz, Ana|||0000-0003-3366-0729
[EN] The aim of this paper is to analyse the discourse produced by participants of a bilingual telecollaboration project and its pragmatic implications. Based on Picoli and Salomão¿s (2020) `principle of equality¿, instances of translanguaging were sought and analysed. The participants in the telecollaboration project were a group of seven Spanish-speaking students of English and a group of seven English-speaking students of Spanish who engaged in synchronous Zoom sessions for six weeks. Learners were expected to perform a role-play per week, after which they were given free time to practise oral conversation in both English and Spanish. Data were gathered from the transcription of the oral conversations. A total number of 23 conversations were analysed quantitatively and qualitatively. After categorising all the usage instances, the results revealed that students mostly used translanguaging for ¿clarification¿, followed by ¿last language used¿, ¿accommodation¿, ¿sequential subordination¿, and ¿solidarity¿. There was evidence that translanguaging was used as a pragmatic strategy to support communication and avoid breakdowns in bilingual or multilingual interactions., The study was funded by Universitat Politècnica de València (Spain), grant number PAID-01-19.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Contribution of green roofs to energy savings in building renovations

  • Garcia-Borràs, Júlia|||0000-0002-5470-0753
  • Lerma Elvira, Carlos|||0000-0003-0436-3725
  • Mas Tomas, Maria De Los Angeles|||0000-0002-0097-0598
  • Vercher Sanchis, José|||0000-0001-9855-4201
  • Gil Benso, Enrique|||0000-0002-6617-640X
[EN] Reversing the consequences of climate change and achieving more resilient societies involves reducing CO2 emissions and energy consumption, especially in sectors as important as construction. Green roofs, due to their particularities, imply a series of benefits, among which energy saving stands out. This implies a reduction in the consumption of resources and in CO2 emissions, more evident in the case of the refurbishment of buildings. A comparison is proposed between the energy savings obtained by renovating only the roof and renovating the entire thermal envelope. This is done with three roof construction systems (including two green roofs) and in 6 Spanish cities that represent different climatic zones. The novelties provided by this research are based on the comparison of both renovation cases to obtain the influence of the roof with respect to the thermal improvement of the envelope. The energy savings obtained by renovating the roof are very similar in all cities, but after renovating the entire envelope, the savings increase as the climate gets colder.Determining themost influential variables in these savings, as well as the influence of the roof, allows choosing the most appropriate construction techniques to optimize the energy renovation of existing buildings., Fundingforopenaccesscharge:CRUE-UniversitatPolitècnicadeValència.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Cider apple pomace as a source of nutrients: Evaluation of the polyphenolic profile, antioxidant and fiber properties after drying process at different temperatures

  • Llavata-Cabrero, Beatriz
  • Picinelli, A.
  • Simal, S.
  • Carcel, J. A.|||0000-0002-3796-6146
[EN] Apple pomace, the by-product of the cider industry, contains a high content of antioxidant compounds and dietary fiber. Drying would allow its preservation for a later use. The aim of this study was to evaluate the effect of the drying temperature on the drying kinetics, antioxidant properties and the fiber characteristics. For this, drying experiments were performed at different temperatures (40-120 degrees C). The increase in temperature enhanced the drying rate, as was shown by the effective diffusivity and mass transfer coefficient identified by modelling. The influence of temperature was quantified through the activation energy (38.21 kJ/mol). Regarding the retention of antioxidant properties, the best results were found at 80-100 degrees C while 40-60 degrees C was the best temperature range for the fiber characteristics. Therefore, 80 degrees C could be an adequate temperature for drying of cider apple pomace, as it represents a good balance between kinetics, and antioxidant and fiber properties., The authors acknowledge the financial support from the grant PID2019-106148RRC42 and PID2019-106148RRC43 funded by MCIN/AEI/10.13039/501100011033, the grant for open access charge of the Universitat Politècnica de València and the PhD grant of Beatriz Llavata from the Universitat Politecnica de Valencia (PAID-01-19).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Direct membrane filtration of municipal wastewater: Effects on biogas production, anaerobic biodegradability and settling properties of the up-concentrated stream

  • Ivailova, Ivana
  • Giménez, J.B.
  • Aguado García, Daniel|||0000-0002-6417-366X
  • Serralta Sevilla, Joaquín|||0000-0001-5015-0689
[EN] Direct membrane filtration (DMF), which can increase the amount of organic matter derived to anaerobic digestion, has emerged as a feasible option for implementing the principles of the Circular Economy in Wastewater Treatment Plants (WWTP). In this work, the effect of DMF on the anaerobic digestion performance and the sedimentation properties of the up-concentrated stream, for which a DMF pilot plant and a laboratory scale mesophilic anaerobic digester were operated for a period of two years, were evaluated. Since the DMF can be placed either after the pretreatment or after the primary settler, the pilot plant was fed with both raw and settled wastewater during the experimental period. The primary sludge and the up-concentrated stream were thickened and fed to the anaerobic digester. The results showed that including an ultrafiltration module in the WWTP increases biogas production of anaerobic digestion, whatever its location. The findings showed an increase of 28-52 % in the amount of organic matter that reached anaerobic digestion that led to an increase of 45-74 % in daily biogas production. A 0.663 kWh.kgCODrem-1 / 0.256 kWh.m-3 inf energy recovery related to anaerobic digestion has been found when including the DMF after the pretreatment. Better settling properties were obtained when the DMF was placed after the pretreatment, while there was no improvement when PAClwas added as a coagulant., This work was partly supported by the Ministry of Science and Innovation through the project MEM4REC (CTM2017-86751-C2) and RECREATE (PID2020-114315RB-C22) and by the Universitat Politecnica de Valencia through a research contract on the first author (PAID-01-19).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Evaluation of Different Compatibilization Strategies to Improve the Performance of Injection-Molded Green Composite Pieces Made of Polylactide Reinforced with Short Flaxseed Fibers

  • Agüero, Ángel
  • Rojas-Lema, Sandra Paola
  • Garcia-Sanoguera, David|||0000-0002-1923-9519
  • Lascano-Aimacaña, Diego Sebastián|||0000-0002-0996-1946
  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Fenollar, Octavio|||0000-0003-4323-7414
  • Torres-Giner, Sergio|||0000-0001-9071-9542
[EN] Green composites made of polylactide (PLA) and short flaxseed fibers (FFs) at 20 wt % were successfully compounded by twin-screw extrusion (TSE) and subsequently shaped into pieces by injection molding. The linen waste derived FFs were subjected to an alkalization pretreatment to remove impurities, improve the fiber surface quality, and make the fibers more hydrophobic. The alkali-pretreated FFs successfully reinforced PLA, leading to green composite pieces with higher mechanical strength. However, the pieces also showed lower ductility and toughness and the lignocellulosic fibers easily detached during fracture due to the absence or low interfacial adhesion with the biopolyester matrix. Therefore, four different compatibilization strategies were carried out to enhance the fiber-matrix interfacial adhesion. These routes consisted on the silanization of the alkalized FFs with a glycidyl silane, namely (3-glycidyloxypropyl) trimethoxysilane (GPTMS), and the reactive extrusion (REX) with three compatibilizers, namely a multi-functional epoxy-based styrene-acrylic oligomer (ESAO), a random copolymer of poly(styrene-co-glycidyl methacrylate) (PS-co-GMA), and maleinized linseed oil (MLO). The results showed that all the here-tested compatibilizers improved mechanical strength, ductility, and toughness as well as the thermal stability and thermomechanical properties of the green composite pieces. The highest interfacial adhesion was observed in the green composite pieces containing the silanized fibers. Interestingly, PS-co-GMA and, more intensely, ESAO yielded the pieces with the highest mechanical performance due to the higher reactivity of these additives with both composite components and their chain-extension action, whereas MLO led to the most ductile pieces due to its secondary role as plasticizer for PLA., This research work was funded by the Spanish Ministry of Science and Innovation (MICI) project numbers RTI2018-097249-B-C21 and MAT2017-84909-C2-2-R. D.L. and J.I.-M. thanks UPV for the grant received through the PAID-01-18 and PAID-01-19 (SP2019001) programs, respectively. S.T.-G. is recipient of a Juan de la Cierva contract (IJCI-2016-29675) from MICIU while S.R.J. is funded through the Santiago Gisolía contract (GRISOLIAP/2019/132) from Generalitat Valenciana (GVA). The microscopy services of UPV are also acknowledged for their help in collecting and analyzing the FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On Projectional Skeletons and the Plichko Property in Lipschitz-Free Banach Spaces

  • Guirao Sánchez, Antonio José|||0000-0002-1031-3954
  • Montesinos Santalucia, Vicente
  • Quilis-Sandemetrio, Andres
[EN] We study projectional skeletons and the Plichko property in Lipschitz-free spaces, relating these concepts to the geometry of the underlying metric space. Specifically, we identify a metric property that characterizes the Plichko property witnessed by Dirac measures in the associated Lipschitz-free space. We also show that the Lipschitz-free space of all R-trees has the Plichko property witnessed by molecules and define the concept of retractional trees to generalize this result to a bigger class of metric spaces. Finally, we show that no separable subspace of l(infinity) containing c0 is an r-Lipschitz retract for r < 2, which implies in particular that F(l(infinity)) is not r-Plichko for r < 2., The authors are immensely grateful to Marek Cuth for his remarks and suggestions regarding the first version of this article, which have been key to improving the overall exposition. The authors would also like to thank Abraham Rueda-Zoca, Antonin Prochazka and the anonymous referee for their very useful comments. This research was supported by grant PID2021-122126NB-C33 funded by MCIN/AEI/10.13039/501100011033 and by "ERDF A way of making Europe". The second author's research has been supported by PAID-01-19, by GA23-04776S and by the project SGS22/053/OHK3/1T/13.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Curcumin-Loaded HA-Based Nerve Guidance Conduit with PLA Microfibers-Filled Lumen Enhances Schwann Cell Proliferation and Alignment

  • Fuster-Gómez, Sandra|||0000-0001-5788-3981
  • Martínez-Férriz, Arantxa|||0000-0001-7193-2575
  • Navarro-Páez, Francisco|||0000-0002-4383-3681
  • Monleón Pradas, Manuel|||0000-0001-6457-0414
[EN] Peripheral nerve injuries (PNIs) represent a significant health challenge for society, as they can result in lifelong disabilities. Despite the rapid advancement of tissue engineering technology, the regeneration of peripheral nerves through nerve guidance conduits (NGCs) remains less favorable than the gold standard treatment, nerve autografts. Consequently, improving the effectiveness of NGCs is essential. The objective of this study was to develop a more effective nerve guidance conduit. To achieve this, hyaluronic acid tubular scaffolds were loaded with curcumin, which has been shown to promote peripheral nerve regeneration, and filled with polylactic acid microfibers to encourage directed growth. A physicochemical characterization of this novel NGC was performed to ensure a thorough understanding of its structural features and performance characteristics. The impact of curcumin and PLA microfibers on Schwann cells, a crucial player in nerve regeneration, was evaluated. The sustained release of curcumin from the hyaluronic hydrogel was observed to enhance the proliferation of Schwann cells, which aligned themselves in a parallel fashion with the PLA microfibers. The proliferation and alignment of these cells within the NGC provides an optimal environment for the regeneration of nerves., The authors acknowledge financing from grant PID2021-12661OB-I00 funded by MCIN/AEI/10.12039/501100011033 and by ERDF (BioNerv). FNP acknowledges the CIACIF/2021/249 scholarship from the Generalitat Valenciana (Conselleria de Innovacion, Universidades, Ciencia y Sociedad Digital) and the European Social Fund (ESF). Funding for open access charge: CRUE-Universitat Politecnica de Valencia. The authors also acknowledge the Electron Microscopy Service at the UPV, where the HR-FESEM images were obtained.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Light-responsive bent-core liquid crystals as candidates for energy conversion and storage

  • Domínguez-Candela, Iván|||0000-0003-3288-1079
  • Lora-García, Jaime|||0000-0003-1699-5404
  • Fombuena, Vicent|||0000-0001-7266-6205
  • Zulkhairi, Iman
  • Pintre, Inmaculada
  • Kamalul Aripin, Nurul Fadhilah
  • Ros, Blanca
  • Martinez-Felipe, Alfonso
[EN] We have assessed the potential of light-responsive bent-core liquid crystals as candidate materials for energy conversion and storage applications. Samples comprise two chromophore bent-core compounds containing either one (IP33) or two (IP31) azobenzene groups, and their 5% (molar) mixtures with one non-chromophore bent-core compound (NG75), which was also measured as a reference material. The pristine compounds and their mixtures were introduced in thin transparent Indium Tin Oxide (ITO) cells, and were characterised by polarised optical microscopy, UV-visible spectrophotometry, impedance spectroscopy, and ferroelectric analysis, under different conditions of electrical fields and UV irradiation. All materials display smectic C polar phases (SmCP) except IP31, which forms columnar phases (Col), and IP33, IP31 and their mixtures exhibit light-responsiveness when irradiated at 365 nm due to reversible trans-to-cis photoisomerisation of the azobenzene units. All the bent-core based materials exhibit, at least, two dielectric relaxations, associated with different modes of molecular reorientation under weak alternating electrical fields (1 Vrms), as well as ferroelectric response that leads to permanent polarisation under the application of strong alternating fields (B75 kV cm¿1) at frequencies associated with the Goldstone-mode (1 Hz). Samples show considerable conductivity values and relaxor behaviour for liquid crystals, which can be tuned by application of UV light. In addition, we have induced in IP31 isothermal phase transitions from columnar to smectic phases (via the isotropic melt), by a combination of light and electrical stimuli. Our results confirm the potential of these bent-core compounds as light-harvesters for energy applications., IDC would like to thank the Universitat Politecnica de Valencia (UPV), for the FPI grant (PAID-2019-SP20190013), the Generalitat Valenciana (GVA) and the European Social Fund (ESF), for the FPI grant (ACIF/2020/233) and the mobility grant (CIBEFP/2021/53). NFKA would like to thank Universiti Teknologi MARA (UiTM) for sponsoring her academic sabbatical leave and allowing her to work on this project. AMF would like to thank the Carnegie Trust for the Universities of Scotland, for the Research Incentive Grant RIG008586, the Royal Society and Specac Ltd., for the Research Grant RGS\R1\201397, the Royal Society of Chemistry for the award of a mobility grant (M19-0000), and the Scottish Government and the Royal Society of Edinburgh for the award of a SAPHIRE project. The authors from INMA greatly appreciate financial support from projects of the Spanish Government PGC2018-093761-B-C31 [MCIU/AEI/FEDER, UE] and the Gobierno de Aragon/FEDER (research group E47_20R). Thanks are given to the nuclear magnetic resonance, mass spectrometry, and thermal analysis services of the INMA (Univ. Zaragoza-CSIC)
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Pulsed electric field (PEF) pretreatment impact on the freezing and ultrasound-assisted atmospheric freeze-drying of butternut squash and yellow turnip

  • Llavata-Cabrero, Beatriz
  • Clemente Polo, Gabriela|||0000-0003-1173-9903
  • Bon Corbín, José|||0000-0002-0457-9705
  • Carcel, J. A.|||0000-0002-3796-6146
[EN] This study explores the impact of the application of pulsed electric field (PEF) pretreatment in the freezing and in the power ultrasound-assisted (US) atmospheric freeze-drying (AFD) of two different products: butternut squash and yellow turnip. Two PEF pretreatments were applied, inducing cell disintegration indexes (CDI) of 0.25 and 0.75. The results showed that PEF pretreatments significantly altered the microstructure of butternut squash and yellow turnip, but in a different way. These changes led to a significant shortening of the freezing process by up to 11.6%. Although PEF pretreatments significantly affected the drying rate of AFD, the effect was maximum when combined with ultrasound-assisted AFD. However, the PEF treatment that most enhanced ultrasound-assisted drying kinetics varied between products: a moderate treatment (CDI of 0.25) was most effective for butternut squash (37.3% time reduction), while a more intense treatment (CDI of 0.75) was better in the case of yellow turnip (44.2% time reduction). These findings indicate an enhancement of the atmospheric freeze-drying process achieved through the combined application of PEF and US under adequate conditions., This study was supported by the PID2019-106148RRC42 grants funded by MCIN/AEI/10.13039/501100011033; the PID2022-136889OB-C22 grant funded by MCIN/AEI/10.13039/501100011033 and by ERDF/EU, and the PhD grant of Beatriz Llavata from the Universitat Polit`ecnica de Val`encia (PAID-01-19). Funding for open access charge: Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Contribución de congreso (ConferenceOutput)

A novel inlet boundary condition for VOF-DNS simulations of the primary breakup of prefilming airblast atomizers

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Carreres, Marcos|||0000-0001-6430-6613
  • Moreno-Montagud, Carlos
[EN] Prefilming airblast atomizers are becoming widely used in state-of-the-art aero engines. The planar configuration experimentally studied by the Karlsruhe Institute of Technology (KIT) has been computationally replicated by different research groups through both Large Eddy Simulation (LES) and Direct Numerical Simulation (DNS). The present investigation reports the use of a novel inlet boundary condition for the DNS study of prefilming airblast atomization that allows accounting not only for the inflow turbulence but also for the temporal evolution of the liquid film thickness at the DNS inlet. The methodology implies the resolution of subsequent singlephase LES, two-phase flow LES and two-phase flow DNS. The former simulations are solved by using the interFoam solver from the OpenFoam toolbox, whereas the latter is computed with the PARIS open-source code. Results for a widely known operating condition show a different degree of atomization when the liquid film thickness evolution is accounted for than the one obtained through the use of a constant liquid film thickness at the domain inlet., Research leading to these results has received funding from the Clean Sky 2 Joint Undertaking under European Union¿s Horizon 2020 research and innovation programme through the ESTiMatE project, grant agreement 821418. We acknowledge PRACE for awarding us access to computational resources on JOLIOT CURIE-AMD at GENCI@CEA, France (proposal 2019204944). Support given to Carlos Moreno by Universitat Politècnica de València through the ¿FPI-Subprograma 2¿ grant within the ¿Programa de Apoyo para la Investigación y Desarrollo (PAID-01-19)¿ is acknowledged. We must thank Marco Crialesi and Wojciech Aniszewski for their technical advice on custom modifications on PARIS, and Johan Sundin for his implementation of the contact angle model. We also thank Achille Schmitter, Hugo Martínez and Lucas González for help processing the 1-phase LES, 2-phase LES and DNS, respectively.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Designing stable lead halide perovskite nanocrystals: From a single particle to nanocomposites

  • Collantes-Pablo, Cynthia
  • Teixeira, William|||0000-0002-6729-9508
  • González-Pedro, Victoria|||0000-0002-8133-5958
  • Bañuls Polo, María-José|||0000-0002-2422-7731
  • Maquieira, Angel|||0000-0003-4641-4957
[EN] Metal halide perovskite nanocrystals have attracted substantial interest given their easy manufacturing, superior Photoluminiscence Quantum Yield and striking optical properties. Despite the huge potential of such materials, their practical implementation and future technological applications need to overcome stability drawbacks: spontaneous degradation, which is accelerated by external stressors (i.e., moisture, oxygen, heat, light, and their combinations), poor phase stability and loss of their colloidal stability due to ligand lability. Within this framework, the understanding of their surface chemistry features and ligand-binding patterns plays a key role in improving the robustness and stability of perovskite nanocrystals. This review presents a comprehensive study of state-of-the-art and current challenges in surface chemistry, interface engineering and encapsulation methodologies for stabilizing lead halide perovskite nanoparticles. We first introduced lead halide perovskite structural and optical properties and a brief discussion of synthesis methods. Next, we explored recent developments in encapsulation methods in different protective matrices comprising from core-shell to macroscale nanocomposites. We also analyzed the advantages and shortcomings of each approach according to their final applications. Finally, we concluded with a discussion of open research challenges and future directions in the aforementioned aspects., This work was financially supported by EU FEDER Project ADBIHOL/AEI/10.13039/501100011033 from MCIN/AEI and PROMETEO/2020/094 from the Generalitat Valenciana. C.C. thanks the Spanish Ministry of Economy and Competitiveness for her predoctoral contract (FPI/17 Scholarship) . W.T acknowledges financial support for Ph.D studies (FPI-UPV 2019 grants).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Spanish Melon Landraces: Revealing Useful Diversity by Genomic, Morphological, and Metabolomic Analysis

  • Flores-León, Alejandro
  • Cebolla Cornejo, Jaime|||0000-0002-2607-9920
  • Picó Sirvent, María Belén|||0000-0001-7761-990X
  • Pérez-Moro, Clara
  • Martí-Renau, Raul
  • Beltran, Joaquim
  • Roselló, Salvador
[EN] Spain is a secondary centre of the diversification of the melon (Cucumis melo L.), with high diversity represented in highly appreciated landraces belonging to the Flexuosus and Ibericus groups. A collection of 47 accessions of Flexuosus, Chate, Piel de Sapo, Tendral, Amarillo, Blanco, and Rochet was analysed using a genotyping-by-sequencing (GBS) approach. A total of 66,971 quality SNPs were identified. Genetic analysis differentiated Ibericus accessions and exotic materials (Ameri, Momordica, Kachri, and Agrestis), while Flexuous accessions shared ancestry between them. Within the Ibericus group, no clear genomic distinction could be identified for the different landraces evaluated, with accessions of different landraces showing high genetic similarity. The morphological characterization confirmed that the external colour and fruit shape had been used as recognition patterns for Spanish melon landraces, but variability within a landrace exists. Differences were found in the sugars and acid and volatile profiles of the materials. Flexuosus and Chate melons at the immature commercial stage accumulated malic acid and low levels of hexoses, while Ibericus melons accumulated high contents of sucrose and citric acid. Specific trends could be identified in the Ibericus landraces. Tendral accumulated low levels of sugars and citric acid and high of malic acid, maintaining higher firmness, Rochet reached higher levels of sugars, and Amarillo tended to lower malic acid contents. Interestingly, high variability was found within landraces for the acidic profile, offering possibilities to alter taste tinges. The main volatile organic compounds (VOCs) in Flexuosus and Chate were aldehydes and alcohols, with clear differences between both groups. In the Ibericus landraces, general trends for VOC accumulation could be identified, but, again, a high level of variation exists. This situation highlights the necessity to develop depuration programs to promote on-farm in situ conservation and, at the same time, offers opportunities to establish new breeding program targets and to take advantage of these sources of variation., This work was supported by grants PROMETEO/2017/078 and PROMETEO/2021/072 (to promote excellence groups), funded by Conselleria d'Educacio, Investigacio, Cultura i Esports (Generalitat Valenciana, Spain) and grant AGL2017-85563-C2-1-R-AR, funded by AEI 10.13039/501100011033 and by "ERDF: A way of making Europe". C.P.M. is a recipient of the predoctoral fellowship "Programa de Ayudas de Investigacion y Desarrollo (PAID-01-19)" from Universitat Politecnica de Valencia, R.M. is a recipient of a postdoctoral grant (PAID-10-20) from Universitat Politecnica de Valencia, and A.F.-L. is a recipient of a predoctoral fellowship from Generalitat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Spatio-Temporal Assessment of a Live Fuel Moisture Content Monitoring Model from an Operational Perspective

  • Arcos-Villacís, María Alicia
  • Soriano-Sancho, Jose L.
  • Balaguer-Beser, Ángel|||0000-0003-0039-2641
  • Ruiz Fernández, Luis Ángel|||0000-0003-0073-7259
[EN] Live fuel moisture content (LFMC) is a key determinant of fuel flammability and forest fire danger; however, its operational monitoring remains challenging due to the limited spatial and temporal coverage of field measurements. This study aims to assess the operational suitability of a Random Forest-based methodology for LFMC estimation by extending a previously validated local-scale approach to a regional and multi-year context. Weighted average LFMC was modeled across 67 shrubland plots in the Valencian Region (eastern Spain) from 2017 to 2025 using Sentinel-2 spectral indices and aggregated meteorological variables consistent with prior research. Model performance was evaluated under spatially independent and combined spatio-temporal training-testing scenarios designed to approximate real-world wildfire monitoring conditions. Results show that the model exhibits good spatial transferability when applied to shrubland plots not used during training within the same temporal domain, while temporal extrapolation is more limited and dependent on the stability of climatic conditions represented in the training data, with a marked decline in performance under changing temperature and precipitation regimes. These findings highlight key drivers of LFMC prediction, identify validation strategies under operational constraints, and contribute to the development of scalable monitoring approaches for wildfire danger assessment and fuel management in Mediterranean shrublands., Maria Alicia Arcos gives thanks for the help received by the Universitat Politecnica de Valencia through a pre-doctoral contract financed in the call, PAID-01-19, subprogram 1. This research has been supported by the grant PID2024-158591OB-I00, funded by MICIU/AEI/10.13039/501100011033 and the European Social Fund Plus (ESF+).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Lipschitz retractions and complementation properties in Banach spaces

  • Hájek, Petr
  • Quilis-Sandemetrio, Andres
[EN] In the present paper we introduce and study the Lipschitz retractional structure of metric spaces. This topic was motivated by the analogous projectional structure of Banach spaces, a topic that has been thoroughly investigated. The more general metric setting fits well with the currently active theory of Lipschitz free spaces and spaces of Lipschitz functions. Among our applications we show that the Lipschitz free space F(X) is a Plichko space whenever X is a Plichko Banach space. Our main results include two examples of metric spaces. The first one M contains two points {0, 1} such that no separable subset of M containing these points is a Lipschitz retract of M. The second example fails the analogous property for arbitrary infinite density. Finally, we introduce the metric version of the concept of locally complemented Banach subspace, and prove some metric analogues to the linear theory., This research was supported by CAAS CZ.02.1.01/0.0/0.0/16-019/0000778,bytheprojectSGS21/056/OHK3/1T/13andbyPAID-01-19. The authors also wish to thank the anonymous referee for their insightful remarks.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Introgression of virus and fungal resistance into traditional genetic backgrounds of melon and Cucurbita spp.

  • Pérez Moro, Clara
[ES] La familia de las cucurbitáceas representa uno de los grupos hortícolas más extensos y ampliamente cultivados. En ella se incluyen especies de gran relevancia económica a nivel mundial, como el melón y el calabacín, entre otras. Sin embargo, su producción se ve gravemente amenazada por numerosos estreses bióticos, entre ellos virus como el Tomato leaf curl New Delhi virus (ToLCNDV). Este virus ha emergido en los últimos años como uno de los principales problemas fitosanitarios que afectan a las cucurbitáceas en regiones mediterráneas y asiáticas. Este begomovirus, transmitido principalmente por la mosca blanca (Bemisia tabaci), causa amarilleo, mosaico y acucharado en las hojas y en algunas especies puede producir deformaciones en los frutos y detención en el crecimiento de la planta, reduciendo drásticamente el rendimiento y la calidad de los cultivos. En la presente tesis se ha abordado la mejora genética de distintas especies de cucurbitáceas para conferirles resistencia a ToLCNDV y a otros patógenos relevantes, sin comprometer las características organolépticas propias de las variedades tradicionales. Para ello, en primer lugar, se ha profundizado en el conocimiento del control genético de las resistencias y se han desarrollado marcadores moleculares asociados a las mismas. En concreto, en el caso de melón se ha trabajado con la resistencia derivada de las entradas de origen indio WM-7 (grupo kachri) y PI 414723 (grupo momordica). La resistencia de la entrada WM-7 había sido caracterizada en trabajos previos del grupo de investigación. El análisis de poblaciones segregantes en el marco de la tesis ha permitido estrechar la región candidata del cromosoma 11 asociada a la resistencia derivada de esta entrada. En el caso de la entrada PI 414723 se ha comprobado que la región asociada a la resistencia es solapante con la identificada en la entrada WM-7. En ambos casos, la región contiene el gen que codifica la subunidad grande de la DNA primasa, gen propuesto en estudios previos como principal candidato para la resistencia a ToLCNDV. Además, mediante análisis BSR-seq combinado con análisis de expresión diferencial, se han identificado otros genes del cromosoma 2 potencialmente implicados en la resistencia derivada de PI 414723. Los marcadores moleculares desarrollados a partir de la información de estos trabajos han permitido acelerar los programas de mejora de introgresión de resistencia a ToLCNDV en variedades tradicionales de melón. Paralelamente, se han empleado marcadores moleculares previamente descritos para introgresar resistencia frente a otros virus como WMV, ZYMV, CMV, y frente a hongos como el oídio, con el fin de generar nuevas líneas multirresistentes de melón adaptadas a la agricultura sostenible. En el caso del programa de mejora de calabacín, se ha estudiado la resistencia derivada de dos entradas de Cucurbita moschata, la entrada india PI 381814 y la variedad tradicional española AN-CU-45. Se ha confirmado que la resistencia derivada de ambas fuentes tiene un control genético común, estando implicado el gen de Cucurbita moschata ortólogo del gen de melón que codifica la subunidad grande de la ADN primasa. Los marcadores moleculares descritos asociados a la resistencia serán de utilidad en el desarrollo de programas de mejora. Además, la entrada AN-CU-45 tiene especial interés por su adaptación al clima mediterráneo y su compatibilidad con C. pepo. Estos estudios se han completado con la identificación de marcadores moleculares asociados a otras características de interés en calabacín. Por una parte, se ha comparado la distribución de variantes genómicas en tres accesiones de calabacín con diferente respuesta frente a ZYMV y oídio. Además, se ha realizado una búsqueda de variantes en genes candidatos asociados a caracteres de calidad, con especial atención a la identificación de genes candidatos relacionados con la arquitectura de la planta, forma del fruto, forma de la hoja y color de la piel del fruto., [CA] La família de les cucurbitàcies representa un dels grups hortícoles més extensos i àmpliament cultivats. Inclou espècies de gran rellevància econòmica a escala mundial, com ara el meló i el carabassí, entre altres. Tanmateix, la seua producció es veu greument amenaçada per nombrosos estressos biòtics, entre els quals destaquen els virus com el Tomato leaf curl New Delhi virus (ToLCNDV). Aquest virus ha emergit en els últims anys com un dels principals problemes fitosanitaris que afecten les cucurbitàcies en regions mediterrànies i asiàtiques. Aquest begomovirus, transmés principalment per la mosca blanca (Bemisia tabaci), causa engroguiment, mosaic i arrissament en les fulles, i en algunes espècies pot produir deformacions en els fruits i atur en el creixement de la planta, la qual cosa redueix dràsticament el rendiment i la qualitat dels cultius. En la present tesi s'ha abordat la millora genètica de diferents espècies de cucurbitàcies per conferir-los resistència a ToLCNDV i a altres patògens rellevants, sense comprometre les característiques organolèptiques pròpies de les varietats tradicionals. Per a això, en primer lloc, s'ha aprofundit en el coneixement del control genètic de les resistències i s'han desenvolupat marcadors moleculars associats a aquestes. En concret, en el cas del meló s'ha treballat amb la resistència derivada de les entrades d'origen indi WM-7 (grup kachri) i PI 414723 (grup momordica). La resistència de l'entrada WM-7 havia sigut caracteritzada en treballs previs del grup d'investigació. L'anàlisi de poblacions segregants en el marc de la tesi ha permés acotar la regió candidata del cromosoma 11 associada a la resistència derivada d'aquesta entrada. En el cas de l'entrada PI 414723 s'ha comprovat que la regió associada a la resistència és solapant amb la identificada en l'entrada WM-7. En ambdós casos, la regió conté el gen que codifica la subunitat gran de la DNA primasa, gen proposat en estudis previs com a principal candidat per a la resistència a ToLCNDV. A més, mitjançant l'anàlisi BSR-seq combinat amb l'anàlisi d'expressió diferencial, s'han identificat altres gens del cromosoma 2 potencialment implicats en la resistència derivada de PI 414723. Els marcadors moleculars desenvolupats a partir de la informació d'aquests treballs han permés accelerar els programes de millora per a la introgressió de la resistència a ToLCNDV en varietats tradicionals de meló. Paral·lelament, s'han emprat marcadors moleculars prèviament descrits per a introgressar resistència davant altres virus com WMV, ZYMV, CMV, i davant fongs com l'oïdi, amb la finalitat de generar noves línies multiresistents de meló adaptades a l'agricultura sostenible. En el cas del programa de millora del carabassí, s'ha estudiat la resistència derivada de dues entrades de Cucurbita moschata: l'entrada índia PI 381814 i la varietat tradicional espanyola AN-CU-45. S'ha confirmat que la resistència derivada d'ambdues fonts té un control genètic comú, i hi està implicat el gen de Cucurbita moschata ortòleg del gen de meló que codifica la subunitat gran de la DNA primasa. Els marcadors moleculars descrits associats a la resistència seran útils en el desenvolupament de programes de millora. A més, l'entrada AN-CU-45 és d'especial interés per la seua adaptació al clima mediterrani i la seua compatibilitat amb C. pepo. Aquests estudis s'han completat amb la identificació de marcadors moleculars associats a altres característiques d'interés en carabassí. D'una banda, s'ha comparat la distribució de variants genòmiques en tres accessions de carabassí amb diferent resposta davant ZYMV i oïdi. A més, s'ha realitzat una cerca de variants en gens candidats associats a caràcters de qualitat, amb especial atenció a la identificació de gens candidats relacionats amb l'arquitectura de la planta, la forma del fruit, la forma de la fulla i el color de l'epidermis del fruit., [EN] The Cucurbitaceae family is one of the largest and most widely cultivated groups of horticultural crops. It includes species of major global economic importance, such as melon (Cucumis melo) and zucchini (Cucurbita pepo), among others. However, their cultivation is seriously threatened by numerous biotic stresses, including viruses such as Tomato leaf curl New Delhi virus (ToLCNDV). This virus has emerged in recent years as one of the main phytosanitary threats to cucurbits in the Mediterranean and Asian regions. ToLCNDV, a begomovirus mainly transmitted by the whitefly (Bemisia tabaci), causes leaf yellowing, mosaic, and curling symptoms. In some species, it also leads to fruit malformations and stunted plant growth, drastically reducing crop yield and quality. This thesis focuses on breeding different cucurbit species to carry resistance to ToLCNDV and other important pathogens, without compromising the organoleptic qualities of traditional varieties. To this purpose, the first step was to get a deeper knowledge of the genetic control of resistance traits and developing molecular markers linked to them. Specifically, in the case of melon, research focused on resistance derived from two Indian accessions: WM-7 (kachri group) and PI 414723 (momordica group). Resistance from WM-7 had already been characterized in previous studies by the research group. The analysis of segregating populations in this thesis allowed for the narrowing down of the candidate region on chromosome 11 associated with resistance from this accession. For PI 414723, the resistance-associated region was confirmed to overlap with that identified in WM-7. In both cases, the region contains the gene encoding a DNA primase large subunit, which has been proposed in previous studies as the main candidate for ToLCNDV resistance. Moreover, through BSR-seq combined with differential expression analysis, additional genes on chromosome 2 were identified as potentially involved in the resistance derived from PI 414723. The molecular markers developed from these studies have allowed the acceleration of breeding programs aimed at introgressing ToLCNDV resistance into melon landraces. In parallel, previously described molecular markers were employed to introgress resistance to other viruses such as Watermelon mosaic virus (WMV), Zucchini yellow mosaic virus (ZYMV), and Cucumber mosaic virus (CMV), as well as to the fungal pathogen Podosphaera xanthii (powdery mildew). The ultimate goal is to develop new multi-resistant melon lines adapted to sustainable agriculture. For the zucchini breeding program, resistance derived from two Cucurbita moschata accessions, the Indian PI 381814 and the traditional Spanish variety AN-CU-45, was investigated. It was confirmed that resistance from both sources is controlled by the same genetic mechanism, involving the C. moschata ortholog of the melon gene encoding the DNA primase large subunit. The associated molecular markers will be valuable tools for future breeding efforts. Notably, AN-CU-45 is of particular interest due to its adaptation to the Mediterranean climate and crossability with C. pepo. These studies were further complemented by the identification of molecular markers associated with other traits of interest in zucchini. On the one hand, the distribution of genomic variants was compared among three zucchini accessions with different responses to ZYMV and powdery mildew. In addition, candidate gene variants were explored for quality-related traits, focusing on genes linked to plant architecture, fruit shape, leaf morphology, and rind color. These markers represent a valuable resource for preserving key quality traits throughout the breeding process., Clara Pérez Moro is a recipient of the predoctoral fellowship “Programa de Ayudas de Investigación y Desarrollo (PAID-01-19)” from Universitat Politècnica de València and the mobility grant “Programa para la Formación de Personal investigador (FPI) de la Universitat Politècnica de València (UPV)”. This work was supported by the grant PID2021-125787OR-C33, funded by MICIU/AEI/10.13039/501100011033; the ‘FEDER UE’ PROMETEO/2021/072 project for excellence groups Conselleria d’Educació, Cultura, Universitats i Ocupació (Generalitat Valenciana, Spain); grant /10.13039/501100011033 and PID2020-116055RB-C21 project funded RTC-2017-6023-2, MICIU/AEI/10.13039/501100011033 and by FEDER ‘A way of making Europe’.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development of a novel epoxy resin based on epoxidized chia oil as matrix and maleinized chia oil as bio-renewable crosslinker

  • Domínguez-Candela, Iván|||0000-0003-3288-1079
  • Lora-García, Jaime|||0000-0003-1699-5404
  • Fombuena, Vicent|||0000-0001-7266-6205
  • Perez-Nakai, Aina
  • Torres-Roca, Elena
[EN] In this work novel thermosetting resins with high bio-based content have been developed derived from chia seed oil (CO). Epoxidized chia seed oil (ECO) was used as bio-based epoxy matrix with different mixtures of crosslinker agents, that is, methyl nadic anhydride (MNA) as petroleum-derived and maleinized chia seed oil (MCO) as bio-based crosslinker. The chemically modified oils from CO, that is, ECO and MCO, and MNA were analyzed by titration and FT-IR. Additional 1H NMR analysis was performed to characterize MCO structure. Two different behaviors were observed using the mixtures of crosslinkers. On one hand, MNA increases the rigidity with bio-based content of 54.2%. On the other hand, the addition of MCO provides higher ductility with bio-based content up to 98%. The same trend was observed by DMTA analysis. The novel cured resins were successfully crosslinked as demonstrated by the mechanical properties, FT-IR analyses, and gel content. Based on the results, it is concluded that MCO presents higher reactivity than MNA, decreasing curing time with possible energy saving at industrial level. In general, the results showed that adding the appropriate amount of MCO, green thermosetting resins with the desired thermal and mechanical properties can be manufactured with high bio-based content., Ministry of Science and Innovation,Grant/Award Number: PID2020-119142RA-I00; Universitat Politecnica de Valencia, Grant/Award Number: PAID-2019-SP20190013; Generalitat Valenciana,Grant/Award Number: ACIF/2020/233. This research work was funded by the Ministry of Science and Innovation-¿Retos de la Sociedad¿. Project references: PID2020-119142RA-I00. I. Dominguez-Candela wants to thank Universitat Politècnica de València for his FPI grant (PAID-2019-SP20190013) and Generalitat Valenciana-GVA (ACIF/2020/233). Funding for open access charge: CRUE-Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Effect of freeze-thaw and PEF pretreatments on the kinetics and microstructure of convective and ultrasound-assisted drying of orange peel

  • Llavata-Cabrero, Beatriz
  • Mello, Ronaldo Elias
  • Correa, J.L.G
  • Quiles Chuliá, Mª Desamparados|||0000-0003-4991-6629
  • Carcel, J. A.|||0000-0002-3796-6146
[EN] The main waste generated by juice industry comprises orange peels, which have a great upcycling potential once stabilized. Drying is the most used method for this purpose, but the high energy consumption prompts interest in its intensification. This study assessed the influence of freeze-thaw and pulsed electric field (PEF) pretreatments in conventional and airborne ultrasound-assisted drying (50 degrees C) of orange peels. None of these pretreatments alone got to reduce processing times significantly, but combined with ultrasound-assisted drying produced a significant shortening of the process. This was particularly important in the lower intensity PEF pretreatment tested (0.33 kJ/kg), indicating the existence of optimum conditions to carry out the pretreatments. Microstructure analysis revealed that the application of ultrasound during drying led to better preservation of the sample structure. Thus, the integration of pretreatment techniques to ultrasound-assisted drying may not only shorten the process but also help to preserve the original structure., This work was supported by the PID2019-106148RRC42 grant funded by MCIN/AEI/ 10.13039/501100011033; PID2022-136889OB-C22 grant funded by MCIN/AEI /10.13039/501100011033/ERDF, a way of making Europe, and the Ph.D. grant of Beatriz Llavata from the Universitat Politecnicade Valencia (PAID-01-19). We are also grateful for the economic support of the Coordenac & atilde;o de Aperfeicoamento de Pessoal de Nivel Superior-Brasil(Capes)-Finance Code 001, Conselho Nacional de Desenvolvimento Cientifico e Tecnologico (CNPq) and Fundac & atilde;o de Amparo a Pesquisa de MinasGerais (FAPEMIG).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Data Homogenization Method for Heterogeneous Sensors Applied to Reinforcement Learning

  • Palacios-Morocho, Maritza Elizabeth
  • López-Muñoz, Pablo
  • Costán, Manuel A.
  • Monserrat del Río, Jose Francisco|||0000-0001-8664-6408
[EN] In autonomous navigation and route planning, the data obtained by the different sensors play a significant role. On the one hand, more data will lead to faster learning of the behavioral policy. On the other hand, agents equipped with different sensors will need more computing power to process the data, thus requiring more robust equipment and increasing the cost of implementation. In addition, the complexity of the algorithms increases as different types of data, i.e., data with different structures, have to be synchronized. Therefore, this paper addresses the problem of homogenization and synchronization of data provided by heterogeneous sensors. Furthermore, it presents a novel method of estimating data in order to provide the agent with a 360-degree view of the environment, similar to that provided by a laser. The method's performance compares the different behavioral policies obtained by different viewing angles of a camera with the policy obtained by a laser. The data obtained from the different viewing angles of each sensor are used in a path planning algorithm, which was designed to use a single 24-scan laser as an input source. The results show that the proposed method is robust since the behavior policies can be reused regardless of the viewing angle with which the sensor (camera) is provided. Furthermore, the proposed novel algorithm achieves an average efficiency of 68% and 94% using a 90 and 360-degree camera, respectively., The work of Elizabeth Palacios-Morocho was supported by the Research and Development Grants Program, Universitat Politecnica deValencia, under Grant PAID-01-19.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Combined Effect of Airborne Ultrasound and Temperature On the Drying Kinetics and Quality Properties of Kiwifruit (Actinidia Deliciosa)

  • Llavata-Cabrero, Beatriz
  • Femenia, A.
  • Clemente Polo, Gabriela|||0000-0003-1173-9903
  • Carcel, J. A.|||0000-0002-3796-6146
[EN] Drying is one of the most used options for the stabilization of the surpluses resulting from kiwifruit industrialization for their upcycling. However, drying conditions, such as drying temperature or ultrasound application during drying to intensify the process, can highly affect its final quality. Thus, with the aim to assess the combined influence of temperature and ultrasound application in the drying process of kiwifruit, ultrasonically assisted drying experiments were performed at 40, 50, 60 and 70 oC. The process kinetics was greatly dependent on the temperature, as shown by the activation energy value obtained, 30.95 kJ/mol. Ultrasound application increased the drying kinetics, with its influence being more marked at the lowest temperatures tested. The increase in effective diffusivity and the mass transfer coefficient induced by ultrasound application was similar to the increase induced by an increase of drying temperature of 10 oC. Drying caused a significant change in the color although the use of ultrasound helped to preserve it at the higher temperatures. Antioxidant capacity and vitamin C content decreased after drying, but the total phenolic content increased. The greatest retention of the antioxidant properties was observed in ultrasonically assisted samples dried at the highest temperatures. In the case of fiber properties, the best results were obtained at intermediate ones. Drying kiwifruit at 60 oC with ultrasound application could serve as a means of balancing a fast drying process and good final quality., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. This work was supported by the grants PID2019-106148RRC42 and PID2019-106148RRC43 funded by MCIN/AEI/10.13039/501100011033 and the PhD grant of Beatriz Llavata and funding for open access charge from the Universitat Politecnica de Valencia (PAID-01-19).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Irrigation proposals for improving the energy performance of green roofs in Mediterranean climate

  • Garcia-Borràs, Júlia|||0000-0002-5470-0753
  • Lerma Elvira, Carlos|||0000-0003-0436-3725
  • Mas Tomas, Maria De Los Angeles|||0000-0002-0097-0598
  • Vercher Sanchis, José|||0000-0001-9855-4201
  • Gil Benso, Enrique|||0000-0002-6617-640X
[EN] The evapotranspiration and cooling energy saving potential of green roofs is very great in the Mediterranean climate, due to high levels of solar radiation. However, the low rainfall limits these losses. The main goal of this research is to determine the energy savings achieved by increasing water availability by installing an irrigation system. It is proposed the computer simulation of a building renovated with three construction systems, according to real scaled models. Irrigation proposals are studied from two perspectives: (1) different irrigation rates for each green roof system and (2) different irrigation schedules. From the perspective of irrigation rates (1) it is observed that increased water input in extensive green roofs does not lead to increased evapotranspiration heat losses due to their limited water storage capacity. In extensive green roofs, increasing the water supply above the storage capacity implies increasing water outflow, but not heat losses. In relation to the irrigation schedules (2) the models with daily annual irrigation achieve very limited total savings, less than 1% compared to self-sustaining models. However, a daily irrigation system only during cooling periods achieves greater total savings, between 1% and 2% compared to self-sustaining models. The system is optimised by increasing energy savings and reducing water consumption. On green roofs in the Mediterranean climate, the increase in available water does not necessarily imply an increase in total energy savings. In these cases, it is essential to find a balance between limiting water consumption and reducing energy consumption., This research has been carried out within the project entitled "Hydrothermal study of green roofs. Analysis and design recommen-dations for greater efficiency" (PAID-01-19-10) , financed by public call by the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Assessment of the fluid-dynamic and acoustic behaviour of a swirl static mixer for after-treatment systems

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Broatch, A.|||0000-0001-9991-1039
  • Quintero-Igeño, Pedro-Manuel|||0000-0003-4373-2079
  • Redondo-Navarro, Álvaro Rafael|||0000-0003-1668-1245
  • Morin, F.
[EN] An investigation on the acoustic transmission loss and the pressure drop caused by a mixer inducing element located downstream of a Diesel Exhaust Fluid (DEF) injection port was carried out in order to reduce the knowledge gap identified for this kind of after-treatment system elements. Transmission Loss measurements were performed at 4 mass flow rate conditions; 0, 100, 200 and 300 kg/h. Additionally, pressure drop measurements were registered for a range of mass flow rates, from 0 to 800 kg/h at steps of 50 kg/h, with similar flow and room temperatures. The post-processing and analysis included the application of a decomposition technique in the case of the transmission loss, which lead to understand the contribution of reflective and dissipative effects to the total attenuation. Reference results are provided for the particular geometry and kind of mixer element characterized, as well as the full extent of the results analysis and the insights of the decomposition analysis technique, and also different modelling possibilities have been explored. The conclusions indicate that, while usually overlooked, these devices may have a significant influence on the exhaust acoustics, mainly due to the influence of their presence on the attenuation of the after-treatment device as a whole. (C) 2021 Elsevier Ltd. All rights reserved., This paper is derived from the research activities developed during the doctoral studies of co-author Alvaro Redondo, which included the characterization of the ATS where the mixer element was located; all his research was supported by the Universitat Politecnica de Valencia (UPV) through the Programa de Ayudas de Investigacion y Desarrollo PAID-01-19 which grants him a predoctoral contract.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Admittance controller complemented with real-time singularity avoidance for rehabilitation parallel robots

  • Pulloquinga-Zapata, José Luis
  • Escarabajal-Sánchez, Rafael José
  • Díaz-Rodríguez, Miguel
  • Vallés Miquel, Marina|||0000-0002-6396-0098
  • Mata Amela, Vicente|||0000-0003-2255-0567
  • Valera Fernández, Ángel|||0000-0001-6843-6394
[EN] Rehabilitation tasks demand robust and accurate trajectory-tracking performance, mainly achieved with parallel robots. In this field, limiting the value of the force exerted on the patient is crucial, especially when an injured limb is involved. In human-robot interaction studies, the admittance controller modifies the location of the robot according to the user efforts driving the end-effector to an arbitrary location within the workspace. However, a parallel robot has singularities within the workspace, making implementing a conventional admittance controller unsafe. Thus, this study proposes an admittance controller that overcomes the limitations of singular configurations by using a real-time singularity avoidance algorithm. The singularity avoidance algorithm modifies the original trajectory based on the actual location of the parallel robot. The complemented admittance controller is applied to a 4 degrees of freedom parallel robot for knee rehabilitation. In this case, the actual location is measured by a 3D tracking system because the location calculated by the forward kinematics is inaccurate in the vicinity of a singularity. The experimental results verify the effectiveness of the proposed admittance controller for safe knee rehabilitation exercises., Acknowledgements This research was partially funded by Fondo Europeo de Desarrollo Regional (PID2021-125694OB-I00), cofounded by Programa de Ayudas de Investigacion y Desarrollo de la Universitat Politecnica de Valencia (PAID-01-19). Funding for open access charge: CRUE-Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Identification of Host Factors Interacting with Movement Proteins of the 30K Family in Nicotiana tabacum

  • Villar-Álvarez, David
  • Leastro, Mikhail Oliveira
  • Pallás Benet, Vicente|||0000-0003-4954-989X
  • Sánchez-Navarro, Jesús-Ángel|||0000-0002-3320-2827
[EN] The interaction of viral proteins with host factors represents a crucial aspect of the infection process in plants. In this work, we developed a strategy to identify host factors in Nicotiana tabacum that interact with movement proteins (MPs) of the 30K family, a group of viral proteins around 30 kDa related to the MP of tobacco mosaic virus, which enables virus movement between plant cells. Using the alfalfa mosaic virus (AMV) MP as a model, we incorporated tags into its coding sequence, without affecting its functionality, enabling the identification of 121 potential interactors through in vivo immunoprecipitation of the tagged MP. Further analysis of five selected candidates (histone 2B (H2B), actin, 14-3-3A protein, eukaryotic initiation factor 4A (elF4A), and a peroxidase-POX-) were conducted using bimolecular fluorescence complementation (BiFC). The interactions between these factors were also studied, revealing that some form part of protein complexes associated with AMV MP. Moreover, H2B, actin, 14-3-3, and eIF4A interacted with other MPs of the 30K family. This observation suggests that, beyond functional and structural features, 30K family MPs may share common interactors. Our results demonstrate that tagging 30K family MPs is an effective strategy to identify host factors associated with these proteins during viral infection., D.V.-A. is a recipient of a predoctoral contract from the Universitat Politecnica of Valencia (PAID-01-19). This work was supported by grants PROMETEO/CIPROM/2022/031 from the Generalitat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Discovery of variation in genes related to agronomic traits by sequencing the genome of Cucurbita pepo varieties

  • Pérez-Moro, Clara
  • D&apos;Esposito, D.
  • Capuozzo, C.
  • Guadagno, A.
  • Ercolano, M.R
  • Pérez De Castro, Ana María|||0000-0002-4949-3323
[EN] BackgroundCucurbita pepo L. cultivars display high morphological traits variation. In addition, C. pepo faces numerous threats, such as viral and fungal infections, which significantly influence crop cultivation. Recent genomic advancements improved the understanding of genetic diversity and stress responses in this crop. We investigated genetic variations related to plant morphology and quality traits. Additionally, the inclusion of both powdery mildew (PM) and Zucchini yellow mosaic virus (ZYMV) susceptible and tolerant varieties facilitated the examination of genetic diversity concerning biotic stress.ResultsThe sequencing of eight Cucurbita pepo varieties produced an average of 40 million raw reads with a coverage of reference genome ranging from 22 to 40X. More than 4.7 million genomic variants were identified in all genomes. Based on admixture and PCA analysis, the eight C. pepo genotypes were grouped in two clusters belonging to Cocozelle and Zucchini groups, with "Whitaker" separated from the rest of the accessions. Genes involved in pathways related to gibberellin regulation, leaf development, and pigment accumulation resulted highly affected by variation suggesting that the diversity observed among varieties in plant and fruit morphology could be related to variants identified in such genes. Each variety showed its own set of genetic differences. The genomic comparison of 381e, 968Rb and SPQ allowed the identification of variants in chromosome regions affecting response to Zucchini yellow mosaic virus (ZYMV) and powdery mildew (PM). Variants in key genes associated with resistant traits were identified, suggesting potential pathways and mechanisms involved in biotic stress response and plant immunity.ConclusionsGenetic variations affecting morphology and fruit quality in C. pepo emphasize their significance for breeding efforts. Furthermore, the genomic comparison of 381e, 968Rb and SPQ highlighted variants in chromosomal regions influencing zucchini's response to PM and ZYMV. These findings could pave the way for more targeted and effective genetic improvement strategies, thereby potentially leading to increased agricultural productivity and quality., This research was funded by the Italian Ministry of University and Research (GenHORT project) and Agritech National Researc Center European Union Next-Generation EU (PIANO NAZIONALE DI RIPRESA E RESILIENZA (PNRR)-MISSIONE 4 COMPONENTE 2, INVESTIMENTO 1.4-D.D. 1032 17/06/2022, CN00000022), CPM is a recipient of the predoctoral fellowship "Programa de Ayudas de Investigacion y Desarrollo (PAID-01-19) de la Universitat Politecnica de Valencia (FPI-UPV )" and mobility grant "Programa para la Formacion de Personal investigador (FPI) de la Universitat Politecnica de Valencia (UPV )".
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Artichoke by Products as a Source of Antioxidant and Fiber: How It Can Be Affected by Drying Temperature

  • Borsini, Ariel A.
  • Llavata-Cabrero, Beatriz
  • Umaña, Mónica
  • Carcel, J. A.|||0000-0002-3796-6146
[EN] The reuse of food industry by-products constitutes one of the essential pillars of the change from a linear to a circular economic model. Drying is one of the most affordable techniques with which to stabilize by¿products, making their subsequent processing possible. However, it can affect material properties. The objective of this study was to assess the effect of the drying temperature on the drying kinetics and final quality of the main artichoke processing by¿products, bracts and stems, which have never been studied as independent materials. For this purpose, air drying experiments at different temperatures (40, 60, 80, 100 and 120 °C) were carried out. The alcohol insoluble residue (AIR) and the total phenolic content (TPC), antioxidant capacity (AC) and vitamin C (VC) of the fresh and dried samples were determined. The bracts dried faster than the stems, increasing drying rate with temperature. The two by¿products presented relatively large amounts of AIR, the content being higher in bracts, but better functional properties in stems. The TPC, AC and VC values of the dried samples decreased in relation to the fresh samples, with the temperatures of 40 °C (bracts) and 120 °C (stems) being the most adequate for the purposes of preserving these characteristics, This research was funded by INIA (Spain)-ERDF, grant number RTA2015-00060-C04-02 and RTA2015-00060-C04-03; Science and Innovation Ministry of Spain and grant number PID2019106148RR-C42. The APC was funded by the Science and Innovation Ministry of Spain, grant number PID2019-106148RR-C42.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Engine Combustion Network &quot, Spray G&quot, : Wall heat transfer characterization by infrared thermography

  • Zaccara, Mirko
  • Montanaro, Alessandro
  • Allocca, Luigi
  • Cardone, Gennaro
  • Carvallo-García, César Leonardo|||0000-0003-2297-2225
  • Gimeno, Jaime|||0000-0003-3317-9994
[EN] Nowadays, several efforts are being made to design more efficient, cleaner, and economically accessible engines. Spray-wall interactions are strongly related with the fuel-air mixture and emission formation. As such, they are considered as the most important physical processes in engine research. In the present study, the infrared thermography coupled with an inverse heat transfer data reduction is applied to evaluate the wall heat transfer of an iso-octane spray generated by a multi-hole gasoline direct injector (Spray G) impinging on a heated thin foil. The experimental apparatus includes an Invar foil (50 mu m in thickness) heated by Joule effect and the injector located at 66.66 injector nozzle diameter above the surface. Thermal images of the impinging spray are acquired from the dry side of the foil at several time delays from the start of injection at two different injection pressures (10 and 20 MPa) and two different wall temperatures (373 and 473 K). The experimental data are reduced in the dimensionless form in terms of the spray cooling efficiency zeta, which represents the ratio between the spray cooling heat flux and the heat transfer capability of the fluid, by taking into account the area of impact of the spray. Results show a substantial increment of the heat flux and the spray cooling efficiency by increasing the wall temperature. Also, the increment of the injection pressure has an increasing effect on the area of impact, the heat flux, and the efficiency of the spray for both wall temperatures investigated in the experimental campaign. The spray cone angle and the plume jet axis angle were also estimated from the wall heat flux distribution., The author C. Carvallo thanks the Universitat Politecnica de Valencia for his predoctoral contract (FPI-2019- S1) which is included within the framework of Programa de Apoyo para la Investigacion y Desarrollo(PAID-01-19) and would also like to say thanks for the mobility economical help provided by the program Ayudas para movilidad dentro del Programa para la Formacion de Personal investigador (FPI) de laUPV''.The authors kindly acknowledge Consiglio Nazionale delle Ricerche- STEMS for hardware and technical support. Funding for open access charge: CRUE-Universitat Politecnica deValencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Enhancing Cooperative Multi-Agent Systems With Self-Advice and Near-Neighbor Priority Collision Control

  • Palacios-Morocho, Maritza Elizabeth
  • Inca-Sánchez, Saúl Adrián
  • Monserrat del Río, Jose Francisco|||0000-0001-8664-6408
[EN] The coordination of actions to be executed by multiple independent agents in a dynamic environment is one of the main challenges of multi-agent systems. To address this type of scenario, a key technology called Reinforcement Learning (RL) has emerged, which enables the training of optimal cooperative policies among agents. However, traditional value decomposition methods suffer fromunstable convergence when the number of agents increases. To address this problem, this article proposes a novel algorithm based on centralized learning that employs a self-advice module to replace the joint action, thereby reducing the algorithmic complexity. The proposed algorithm uses the Joint Action Learning (JAL) concept to find an optimal approach and a collision controller module that was designed to further mitigate the risk of collisions. A comparison of the algorithm proposed is carried out with two benchmark algorithms. The first one focuses on ecomposing the reward signal and the second one trains a different actor-critic network for each agent. Furthermore, multiple target points are defined to enhance cooperative scenarios during the learning process. According to the results, the proposed approach outperforms the two benchmarks by 8% and 49%, thus highlighting the effectiveness of the centralized learning approach in multi-agent systems., Elizabeth Palacios s research was supported by the Research and Development Grants Program under Grant PAID-01-19 of the Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Physicochemical Characterization of Novel Epoxidized Vegetable Oil from Chia Seed Oil

  • Domínguez-Candela, Iván|||0000-0003-3288-1079
  • Cardona, S. C.|||0000-0002-2882-3098
  • Lora-García, Jaime|||0000-0003-1699-5404
  • Fombuena, Vicent|||0000-0001-7266-6205
  • Lerma-Canto, Alejandro
[EN] In this study, a novel epoxidized vegetable oil (EVO) from chia seed oil (CSO) has been obtained, with the aim to be employed in a great variety of green products related to the polymeric industry, as plasticizers and compatibilizers. Previous to the epoxidation process characterization, the fatty acid (FA) composition of CSO was analyzed using gas chromatography (GC). Epoxidation of CSO has been performed using peracetic acid formed in situ with hydrogen peroxide and acetic acid, applying sulfuric acid as catalyst. The effects of key parameters as temperature (60, 70, and 75 degrees C), the molar ratio of hydrogen peroxide:double bond (H2O2:DB) (0.75:1.0 and 1.50:1.0), and reaction time (0-8 h) were evaluated to obtain the highest relative oxirane oxygen yield (Y-oo). The evaluation of the epoxidation process was carried out through iodine value (IV), oxirane oxygen content (O-o), epoxy equivalent weight (EEW), and selectivity (S). The main functional groups were identified by means of FTIR and H-1 NMR spectroscopy. Physical properties were compared in the different assays. The study of different parameters showed that the best epoxidation conditions were carried out at 75 degrees C and H2O2:DB (1.50:1), obtaining an O-o value of 8.26% and an EEW of 193 (g center dot eq(-1)). These high values, even higher than those obtained for commercial epoxidized oils such as soybean or linseed oil, show the potential of the chemical modification of chia seed oil to be used in the development of biopolymers., This research work was funded by the Ministry of Science and Innovation-"Retos de la Sociedad". Project reference: PID2020-119142RA-I00. I. Dominguez-Candela wants to thank Universitat Politecnica de Valencia for his FPI grant (PAID-2019-SP20190013) and Generalitat Valenciana (GVA) for his FPI grant (ACIF/2020/233).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The Affordances of Telecollaboration to Teach Apologies

  • Di Sarno-García, Sofia
[EN] This study presents the results of three telecollaboration projects carried out between Spanish-speaking students and their English-speaking counterparts. The aim is to explore the affordances of telecollaboration for the development of Spanish learners' use of apologies in English. To investigate its suitability, a control group and three experimental groups were set. Quantitative analysis of the responses to a pre- and post-test, as well as quantitative content analysis of the strategies used to apologise in role-playing tasks have been carried out. The results revealed that there is a tendency toward improvement in the three experimental groups, as opposed to the control group. In line with this, the control group used a smaller range of strategies to apologise. It is concluded that the first experimental group is the one that obtained better results than the rest., The author would like to thank Prof. Ana Gimeno-Sanz (Universitat Politecnica de Valencia), Prof. Ana Sevilla-Merino (University of Bath), Prof. Marta Gonzalez-Lloret (University of Hawaii), Prof. Baptista (Morgan State University), and all their students for participating in this study. This project was funded by the Universitat Politecnica de Valencia (PAID-01-19).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Modelos de Machine Learning y estadística multivariante para predecir la posición de los equipos de primera división, Machine Learning and Multivariate Statistics models to predict the position of the first division teams

  • Malagón-Selma, María del Pilar
  • Debón, A.|||0000-0002-5116-289X
  • Ferrer, Alberto|||0000-0001-7244-5947
[EN] This research aims to find which models of Machine Learning and Multivariate Statistics have a greater predictive capacity when deciding what the team's classification will be at the end of the season. The teams that competed in the first division of the Bundesliga, Premier League, LaLiga, Ligue 1 and Serie A throughout the 2018-2019 season have been studied. The badly classified teams by the best of the models, the Random Forest with balanced data, were analyzed in-depth to determine the game's actions that caused the classification error. The results indicate that, generally, the effectiveness in front of goal and the possession of the ball are the statistics in which badly classified teams differ the most with the average of their real position. In conclusion, this research shows how Machine Learning and Multivariate Statistical techniques can be used successfully to discriminate between Top and Bottom teams competing in the best leagues in the world, [ES] Esta investigación tiene como objetivo encontrar qué modelos de Machine Learning y Estadística Multivariante tienen una mayor capacidad de predicción de la posición de los equipos al final de la temporada en la tabla clasificatoria. Se han utilizado las acciones de juego de los equipos que compitieron en la primera división de la Bundesliga, Premier League, LaLiga, Ligue 1 y Serie A, a lo largo de la temporada 2018-2019. Los equipos mal clasificados por el mejor de los modelos, el Random Forest con datos equilibrados, fueron analizados en profundidad para determinar las acciones del juego que provocaban el error de clasificación. Los resultados indican que, generalmente, la efectividad de cara a portería y la posesión del balón son las variables en las que más difieren los equipos mal clasificados respecto a los valores medios de las variables en su grupo real. En conclusión, esta investigación muestra cómo las técnicas de Machine Learning y Estadística Multivariante se pueden utilizar con éxito para predecir la clasificación final de los equipos que compiten en las mejores ligas del mundo., Los autores quieren agradecer a la Universitat Politècnica de València el apoyo económico a través de la beca FPI-UPV (PAID-01-19). Además, agradecen el trabajo de los dos revisores anónimos y el editor, cuyas sugerencias mejoraron el manuscrito original.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Evaluating the performance of spectral indices and meteorological variables as indicators of live fuel moisture content in Mediterranean shrublands

  • Arcos-Villacís, María Alicia
  • Balaguer-Beser, Ángel|||0000-0003-0039-2641
  • Ruiz Fernández, Luis Ángel|||0000-0003-0073-7259
[EN] This article presents a methodology to estimate the live fuel moisture content (LFMC), a critical factor in the spread of forest fires, through machine learning tools. Random forest models were trained using field LFMC samples collected bi-weekly for 18 consecutive months in 43 shrubland plots in the Valencian region, a Mediterranean zone in eastern Spain. LFMC predictions were obtained for the weighted average of LFMC values, calculated using the Fraction of Canopy Cover (FCC) of dominant species as weights. Furthermore, a specific model was defined for predicting LFMC for the Rosmarinus officinalis species. A Forward Feature Selection (FFS) with a Leave-Location-Out Cross Validation (LLOCV) method was used to select predictors extracted from a spatiotemporal data set, which includes different spectral indices obtained from Sentinel-2 imagery and meteorological variables obtained from measurements at weather stations, along with other seasonal, geographical or topographic variables. Model predictions were validated with a LLOCV procedure, and also using independent field measurements of LFMC in another period with changes in the precipitation regime and average temperatures. Variables selected by FFS for the two LFMC models were: the cumulative precipitation in the previous 60 days (p60), the average of the daily mean temperature in the previous 60 days (t60), together with the Y-UTM coordinate and the sine and cosine of the day of the year. LFMC predictions for the weighted average of LFMC values also introduced the Transformed Chlorophyll Absorption Ratio Index (TCARI), resulting in an R2 of 68.1%. However, LFMC for the Rosmarinus officinalis species used the ratio between TCARI and the Optimized SoilAdjusted Vegetation Index (OSAVI), in addition to the average daily minimum relative humidity in the 15 days prior to the date considered (R2 = 74.9 %). LFMC time series analysis showed that the general trend of LFMC measures is satisfactorily captured by the predictions. Spatial and temporal variations in LFMC were analyzed throughout thematic maps in the studied area during the wildfire season., Ma Alicia Arcos gives thanks for the help received by the Universitat Politecnica de Valencia through a pre-doctoral contract financed in the call, PAID-01-19, subprogram 1, and the open access charge: Universitat Politecnica de Valencia (PAID-12-23) . This research was funded by through a collaboration agreement between the company Red Electrica de Espana S.A.U. and the Universitat Politecnica de Valencia (2020-2023) , as well as the research project PID2020-117808RB-C21 funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Performance Evaluation of Onboard Processing Capability Reduction in Cooperative Vehicles Using 5G and Artificial Intelligence

  • Palacios-Morocho, Maritza Elizabeth
  • Inca-Sánchez, Saúl Adrián
  • Monserrat del Río, Jose Francisco|||0000-0001-8664-6408
[EN] Fifth Generation (5G) technology is one of the keys to the industrial revolution known as Industry 4.0 since it provides faster connectivity and allows a greater number of devices to be connected simultaneously. In the transport sector, newly produced vehicles are equipped with various sensors and applications to help drivers perform safe maneuvers. However, moving from semi-autonomous to fully autonomous vehicles to cooperating systems remains a major challenge. Many researchers have focused on Artificial Intelligence (AI) techniques and the ability to share information to achieve this cooperative behavior. This information can be made up of different data, which can be obtained from different sensors such as Laser Imaging Detection and Ranging (LiDAR), radar, camera, Global Positioning System (GPS), or data related to the current speed, acceleration, or position. The combination of the different shared data is performed depending on the approach of each navigation algorithm. This data fusion will allow a better understanding of the environment but will overload the network, as the traffic generated will be massive. Therefore, this paper addresses the challenge of achieving this cooperation between vehicles from the point of view of network requirements and computational capacity. In addition, this study contributes to advancing theory into real-world practice by examining the performance of cooperative navigation algorithms in the midst of the migration of computational resources from onboard vehicle equipment to the cloud. Specifically, it investigates the transition from a cooperative navigation algorithm based on a decentralized architecture to a semi-decentralized one as computationally demanding processes previously performed onboard are performed in the cloud. Additionally, the paper discusses the indispensable role of 5G in fulfilling the escalating demands for high throughput and low latency in these services, particularly as the number of vehicles increases. The results of the tests show that the AI acting alone cannot achieve optimal performance, even using 100% of the computational capacity of the onboard equipment in the vehicle. However, a system that integrates 5G and AI-based joint decisions can achieve better performance, reduce the computational resources consumed in the vehicle, and increase the efficiency of collaborative choices by up to 83.3%, Elizabeth Palacios s research was funded by the Research and Development Grants Program (PAID-01-19) of the Polytechnic University of Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Acoustic and Fluid-Dynamic Characterization of State-of-the-Art Exhaust After-Treatment Systems

  • Redondo-Navarro, Álvaro Rafael|||0000-0003-1668-1245
[ES] Las normativas sobre emisiones contaminantes y sonoras, cada vez más estrictas, han sido la principal motivación para la investigación, el desarrollo y la optimización de los motores de combustión y demás tecnologías relacionadas. Esta tendencia ha dado lugar a la introducción paulatina de sistemas de postratamiento para reducir las emisiones contaminantes provenientes de la automoción. Se emplearon diferentes enfoques experimentales y de modelado computacional para estudiar y caracterizar el comportamiento acústico y fluidodinámico de un conjunto diverso de sistemas de postratamiento, abarcando así una amplia gama de elementos y características representativos de las aplicaciones de postratamiento más avanzadas de uso comercial. La pérdida por transmisión y la caída de presión fueron seleccionadas como parámetros clave de estudio para cuantificar la atenuación acústica y la contrapresión generada por cada dispositivo. Para la caracterización experimental se utilizaron procedimientos de medición bien establecidos. Por su parte, para el modelado computacional se emplearon distintos enfoques de simulación, tales como el unidimensional, el CFD e incluso la co-simulación 1D-3D, siguiendo en la medida lo posible el concepto o principio "gemelos digitales", en programas comerciales con el objetivo de replicar los resultados experimentales, a fin de obtener información complementaria y ayudar a profundizar en la comprensión de los fenómenos internos, los efectos tridimensionales del flujo y los efectos acústicos. Previo a la caracterización minuciosa de los dispositivos, se verificó la validez y significancia de las medidas acústicas en condiciones frías como las que se iban a tomar, para representar los dispositivos respecto a sus condiciones reales de funcionamiento, es decir, expuestos a flujo caliente y pulsante como en el extremo caliente de las líneas de escape donde habitualmente se sitúan los sistemas de postratamiento. Una vez realizada esta validación. Comenzó se dio paso a la caracterización experimental, para cada sistema o dispositivo se registraron mediciones de caída de presión para un rango de caudales násicos, normalmente entre 0 y 800 kg/h. Del mismo modo, se efectuaron mediciones de pérdida de transmisión en condiciones de ausencia de flujo y con tres caudales masicos diferentes superpuestos, por lo general 100, 200 y 300 kg/h. La información producida, tras cierto post-procesamiento, análisis por descomposición y comparativo, sumado al uso del razonamiento inductivo fueron empleados para cuantificar y relacionar cada elemento con sus efectos. Adicionalmente otros temas fueron evaluados, como el cumplimiento de la propiedad aditiva en los resultados de caída de presión y pérdida por transmisión cuando varios dispositivos de postratamiento se disponen juntos formando un sistema, la importancia real de los dispositivos auxiliares que a menudo son pasados por alto , los cambios en los inicios de la vida útil de un dispositivo con filtro de partículas tipo GPF, las ventajas de realizar análisis por descomposición en los resultados de pérdida por transmisión, las capacidades de 1D y 3D CFD para producir información útil y los beneficios eventuales de la co-simulación 1D-3D. En conjunto, se elaboró una base de datos exhaustiva sobre la caída de presión y la pérdida de transmisión de los dispositivos y sistemas de postratamiento más avanzados. Las metodologías experimentales utilizadas, con su correspondiente posprocesado, demostraron ser adecuadas y producir información significativa. Especialmente tras la validación realizada con las mediciones acústicas en condiciones ambientales relativas a condiciones similares a las reales en el motor., [CA] Les normatives sobre emissions contaminants i sonores, cada vegada més estrictes, han sigut la principal motivació per a la investigació, el desenvolupament i l'optimització dels motors de combustió i altres tecnologies relacionades. Aquesta tendència ha donat lloc a la introducció gradual de sistemes de post-tractament per a reduir les emissions contaminants provinents de l'automoció. Es van emprar diferents enfocaments experimentals i de modelatge computacional per a estudiar i caracteritzar el comportament acústic i fluidodinàmic d'un conjunt variat de sistemes i dispositius de post-tractament, abastant així una àmplia gamma d'elements i característiques representatius de les aplicacions de post-tractament més avançades d'ús comercial. La pèrdua per transmissió i la caiguda de pressió van ser seleccionades com a paràmetres clau d'estudi per a quantificar l'atenuació acústica i la contrapressió generada per cada dispositiu. Per a la caracterització experimental es van utilitzar instal·lacions i procediments de mesura ben establits. Per part seua, per al modelatge computacional es van emprar diferents enfocaments de simulació, com ara l'unidimensional, el CFD (tridimensional) i fins i tot la co-simulació 1D-3D, seguint en la mesura del possible el concepte o principi ``bessons digitals'' (virtual twinning), en programes comercials amb l'objectiu de replicar els resultats experimentals, a fi d'obtindre informació complementària i ajudar a aprofundir en la comprensió dels fenòmens interns, els efectes tridimensionals del flux i els efectes acústics. Previ a la caracterització minuciosa dels dispositius, es va verificar la validesa i significança de les mesures acústiques en condicions fredes (ambient), com les que s'anaven a prendre, per a representar els dispositius respecte a les seues condicions reals de funcionament, és a dir, exposats a flux calent i periòdic com en l'extrem calent de les línies de escapament on habitualment se situen els sistemes de post-tractament. Una vegada realitzada aquesta validació, per a cada sistema o dispositiu es van registrar mesures de caiguda de pressió per a un rang de cabals màssics, normalment entre 0 i 800 kg/h. De la mateixa manera, es van efectuar mesures de pèrdua de transmissió en condicions d'absència de flux i amb tres cabals màssics diferents superposats, en general 100, 200 i 300 kg/h. La informació produïda, després d'un cert post-processament, anàlisi per descomposició i comparatiu, sumat a l'ús del raonament inductiu van ser emprats per a quantificar i relacionar cada element amb els seus efectes. Addicionalment altres temes van ser avaluats, com el compliment de la propietat additiva en els resultats de caiguda de pressió i pèrdua per transmissió quan diversos dispositius de post-tractament es disposen junts formant un sistema, la importància real dels dispositius auxiliars que sovint són passats per alt, els canvis en els inicis de la vida útil d'un dispositiu amb filtre de partícules tipus GPF, els avantatges de realitzar anàlisis per descomposició en els resultats de pèrdua per transmissió, les capacitats dels models 1D i 3D CFD per a produir informació útil, i els beneficis eventuals de la co-simulació 1D-3D. En conjunt, es va elaborar una base de dades exhaustiva sobre la caiguda de pressió i la pèrdua de transmissió dels dispositius i sistemes de post-tractament més avançats. Les metodologies experimentals utilitzades, amb el seu corresponent post-processament, van demostrar ser adequades i produir informació significativa. Especialment després de la validació realitzada amb les mesures acústiques en condicions ambientals relatives a condicions similars a les reals en el motor., [EN] Continuously tightening pollutant and noise emission regulations have been the key motivation for engine -and engine related technology- research, development and optimization. Such trend gave rise to the gradual introduction of after-treatment systems to reduce pollutant emissions in automotive applications. Experimental and modelling approaches were used to study and characterize the acoustic and fluid-dynamic behavior of a diverse set of state-of-the-art after-treatment systems and devices, covering a wide range of elements and characteristics representative of after-treatment applications of commercial use. Transmission loss and pressure drop were selected as the key parameters to account for the sound attenuation and back-pressure generated by each device. Well established measurement facilities and procedures were used for the experimental characterization. In parallel, 1D, 3D CFD and even coupled 1D-3D simulation approaches on the basis of the "virtual twinning" concept were implemented on commercial software, aiming to replicate the experimental results in order to provide additional information and help deepen the understanding of internal phenomena, three-dimensional flow and acoustic effects. Prior to the thorough characterization of the devices, the validity and significance of acoustic cold (ambient) condition measurements, as those to be taken, to represent the devices in their actual operating condition, i.e. hot and pulsating-flow as in the hot-end of exhaust lines were after-treatment systems are usually placed, was verified. Once such validation was done, for each system or device pressure drop measurements were performed for a range of mass flow rates, usually between 0 to 800 kg/h. Similarly, transmission loss measurements were performed at no-flow condition and with three different superimposed mean mas flow rates, commonly 100, 200 and 300 kg/h. The information produced, with some post-processing, decomposition and comparative analysis, and the use of inductive reasoning were used to account and relate each element with their effects. Additionally, some other topics were assessed, such as the compliance of the additivity property of pressure drop and the transmission loss when several after-treatment devices are arranged together as an after-treatment system, the actual importance of auxiliary devices often overlooked, the changes in the early service life of a device with a GPF monolith, the benefits of performing decomposition analysis to the transmission loss, the capabilities of 1D and 3D CFD to produce useful information and the eventual benefits of 1D-3D co-simulation. Overall, a comprehensive database on the pressure drop and transmission loss of state-of-the-art after-treatment devices and systems was produced. The experimental methodologies used, with their corresponding post processing, proved to be adequate and to produce significant information, especially after the validation of ambient condition acoustic measurements regarding engine-like conditions., This research has been funded by the Programa de Ayudas de Investigación y Desarrollo PAID-01-19, from Universitat Politècnica de València (UPV), which granted my pre-doctoral contract.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Hyaluronic Acid Ultra-Porous Scaffolds Reinforced with Low Quantities of Graphene Oxide: Influence on the Delivery of Curcumin and Bacterial Inhibition

  • Fuster-Gómez, Sandra|||0000-0001-5788-3981
  • Campillo-Fernández, Alberto J.|||0000-0002-2978-5994
[EN] In this study, the influence of (i) the degree of crosslinking and (ii) incorporating small amounts of graphene oxide¿up to 0.2% by mass¿into the matrix of ultra-porous hyaluronic acid scaffolds was analyzed in relation to their physicochemical and mechanical properties. Also studied was the effect of incorporating graphene oxide on the release profile of curcumin, a hydrophobic molecule of interest in tissue engineering, plus the potential antibacterial activity of graphene oxide against Escherichia coli, E.coli. This paper describes the development of a hybrid ultra-porous material composed of crosslinked hyaluronic acid and graphene oxide, representing a significant advance in the field of nanomedicine. The resulting material enables dual control over the release kinetics of curcumin, a compound with high pharmacological potential and neuroprotective properties., This research was funded by Spanish Ministry of Science, Innovation and Universities through (i) PID2021-126612OB-I00. Also, this research was supported by (ii) UPV-LaFe INBIO innovation projects, PI2023-6. Funding for open access charge: Universitat Politecnica de Valencia through PAID-12-24 program.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Experimental study of the behavior of gasoline direct injection GDI sprays during wall impingement under realistic engine conditions.

  • Carvallo-García, César Leonardo|||0000-0003-2297-2225
[ES] A medida que aumenta la conciencia climática y se buscan reducir las emisiones globales, se están realizando esfuerzos para producir tecnologías que permitan desarrollar motores más limpios y amigables con el medio ambiente. Los sistemas GDI (inyección directa de gasolina) tienen el potencial de cumplir con los cada vez más estrictos estándares de emisiones y, al mismo tiempo, mejorar el consumo de combustible. El espacio limitado dentro de la cámara de combustión hace que el impacto del chorro con la pared sea un fenómeno común en los motores de inyección directa de gasolina. Este fenómeno tiene un efecto significativo en el desarrollo del chorro y su interacción con el aire en la cámara. En condiciones de arranque en frío, las bajas presiones y temperaturas en la cámara facilitan la deposición del combustible en la superficie del pistón, lo que conduce a un aumento considerable en la formación de hollín y en los hidrocarburos sin quemar. Esta tesis busca proporcionar información sobre las características más relevantes de la interacción chorro-pared en sistemas de inyección directa de gasolina en condiciones de arranque en frío y otras condiciones evaporativas. Para ello, se utilizó una pared plana ubicada a diferentes distancias de impacto y ángulos con respecto a la punta del inyector. Se empleó un inyector solenoide fabricado por Continental y el inyector "Spray G", utilizando iso-octano como combustible inyectado. El estudio se llevó a cabo en diversas instalaciones experimentales cubriendo varias técnicas ópticas. El estudio de la interacción chorro-pared se llevó a cabo utilizando tres campañas experimentales. En la primera, se utilizó una pared de cuarzo transparente para analizar las características macroscópicas del chorro al impactar la pared, observándola lateral y frontalmente con el uso de tres cámaras de alta velocidad gracias a los accesos ópticos de la instalación experimental. En la segunda, se empleó una pared termorregulada de acero inoxidable para medir el efecto que tienen las condiciones de operación y ambientales sobre la transferencia de calor entre la pared y el chorro durante el evento de inyección de combustible. Se observó que la penetración del chorro libre y el desarrollo del chorro sobre la pared son influenciados por la presión de inyección y el ángulo de inclinación de la pared. El ancho del chorro medido después del impacto fue afectado principalmente por la distancia entre el inyector y la pared y por el ángulo de la pared pero más aún por la distancia respecto al punto de impacto sobre la cual fue medida. La semi área de impacto es susceptible a cambios en el ángulo de la pared y la distancia inyector-pared teniendo un papel fundamental en el arrastre de aire entre el chorro y el ambiente. No se encontraron diferencias significativas entre las fases líquida y vapor tanto para la penetración de chorro libre como para el desarrollo del chorro sobre la pared a temperatura ambiente. Por el contrario, con la pared calentada, se obtuvieron diferencias entre la fase líquida y vapor, destacando la contribución de la evaporación de combustible causada por el incremento en la temperatura de la pared. Respecto a la pared instrumentada, tanto la temperatura del combustible como de la pared produjeron los picos más significativos en términos del flujo de calor superficial. Órdenes de magnitud similares respecto al flujo de calor superficial fueron encontrados entre las campañas experimentales de la pared instrumentada y la termografía infrarroja. La aparición del flash boiling en condiciones de menor contrapresión ambiental y mayor temperatura del combustible modificó la morfología del chorro en términos de anchura , lo que tuvo repercusiones significativas en el parámetro R (que depende de la penetración del chorro) y en el número de gotas de líquido presentes en el chorro, afectando tanto a los perfiles de extinción de la luz como a los perfiles del flujo de calor superficial., [CA] A mesura que augmenta la consciència climàtica i es busquen reduir les emissions globals, s'estan fent esforços per a produir tecnologies que permeten desenvolupar motors més nets i amigables amb el medi ambient. Els sistemes GDI (injecció directa de gasolina) tenen el potencial de complir amb els estrictes estàndards d'emissions i, al mateix temps, millorar el consum de combustible. L'espai limitat dins de la cambra de combustió fa que l'impacte del doll amb la paret siga un fenomen comú en els motors d'injecció directa de gasolina. Aquest fenomen té un efecte significatiu en el desenvolupament del doll i la seua interacció amb l'aire en la cambra. La interacció doll-paret és un fenomen interessant i difícil de comprendre que ocorre durant el procés de combustió. En condicions d'arrancada en fred, les baixes pressions i temperatures en la cambra faciliten la deposició del combustible en la superfície del pistó, la qual cosa condueix a un augment considerable en la formació de sutge i en els hidrocarburs sense cremar. Aquesta tesi busca proporcionar informació sobre les característiques més rellevants de la interacció doll-paret en sistemes d'injecció directa de gasolina en condicions d'arrancada en fred i altres condicions evaporatives. Per a això, es va utilitzar una paret plana situada a diferents distàncies d'impacte i angles respecte a la punta de l'injector. Es va emprar un injector solenoide fabricat per Continental i l'injector "Spray G", utilitzant iso-octà com a combustible injectat. L'estudi es va dur a terme en diverses instal·lacions experimentals cobrint diverses tècniques òptiques. L'estudi de la interacció doll-paret es va dur a terme utilitzant tres campanyes experimentals. En la primera, es va utilitzar una paret de quars transparent per a analitzar les característiques macroscòpiques del doll en impactar la paret, observant-la lateral i frontalment amb l'ús de tres càmeres d'alta velocitat gràcies als accessos òptics de la instal·lació experimental. En la segona, es va emprar una paret termorregulada d'acer inoxidable per a mesurar l'efecte que tenen les condicions d'operació i ambientals sobre la transferència de calor entre la paret i el doll durant l'esdeveniment d'injecció de combustible. Es va observar que la penetració del doll lliure i el desenvolupament del doll sobre la paret són influenciats per la pressió d'injecció i l'angle d'inclinació de la paret. L'ample del doll mesurat després de l'impacte va ser afectat principalment per la distància entre l'injector i la paret i per l'angle de la paret però més encara per la distància respecte al punt d'impacte sobre la qual va ser mesurada. La semi àrea d'impacte és susceptible a canvis en l'angle de la paret i la distancia injector-paret tenint un paper fonamental en l'arrossegament d'aire entre el doll i l'ambient. No es van trobar diferències significatives entre les fases líquida i vapor tant per a la penetració de doll lliure com per al desenvolupament del doll sobre la paret a temperatura ambient. Per contra, amb la paret calfada, es van obtindre diferències entre la fase líquida i vapor, destacant la contribució de l'evaporació de combustible causada per l'increment en la temperatura de la paret. Respecte a la paret instrumentada, tant la temperatura del combustible com de la paret van produir els pics més significatius en termes del flux de calor superficial. Ordres de magnitud similars respecte al flux de calor superficial van ser trobats entre les campanyes experimentals de la paret instrumentada i la termografia infraroja. L'aparició del flaix boiling en condicions de menor contrapressió ambiental i major temperatura del combustible va modificar la morfologia del doll en termes d'amplària, la qual cosa va tindre repercussions significatives en el paràmetre R i en el nombre de gotes de líquid presents en el doll, afectant tant els perfils d'extinció de la llum com als perfils del flux de calor superfial., [EN] Fuel injection is one of the most important factor that must be considered to achieve cleaner and more efficient internal combustion engines. Its role is more evident when direct injection strategies are used. As awareness of climate change and global emission reduction policies increase, efforts are being made to develop new technologies that enable cleaner and more environmentally friendly engines. The gasoline direct injection systems can fulfill strict emission standards and improve fuel consumption. Because of the space constraints inside the combustion chamber for spray penetration, collision and interaction with the wall are common events in direct injection engines, considerably influencing spray formation and air-spray interaction inside the chamber. In cold-start engine conditions, the lower injection pressures and temperatures in the combustion chamber enhance the fuel deposition over the piston surface, incrementing the soot and the unburned hydrocarbon formation. The present work highlights the fundamental aspects of the spray-wall interaction for the gasoline direct injection (GDI) system under cold-start and other evaporative conditions. For that, a flat wall is located several distances and at different wall angles to the injector tip. Also, this thesis involves using a solenoid injector produced by Continental and the well-known "Spray G" injector using iso-octane as injected fuel covering several techniques and experimental facilities. To analyze the spray-wall interaction, three experimental approaches were used: The first used three high-speed cameras and a quartz wall inside the test rig vessel to study the macroscopic characteristics of the spray, which was observed lateral and frontal by using the optical accesses of the vessel. The second approach used a stainless steel wall to catch the effect of the operating and ambient conditions over the heat flux between the wall and the spray during the fuel injection event and determine how the spray development is affected by the cold-start realistic engine conditions and other evaporative conditions that were included in the test matrix. This wall was coupled with sensors to control the initial surface temperature and to compute the temperature variation in time and the surface heat flux using high-speed thermocouples. The spray under free-jet conditions was also analyzed as a comparison point with the spray-wall interaction conditions. The free spray penetration and the spray spreading over the wall were influenced mainly by the injection pressure and the wall angle. The spray thickness measured after the SWI was affected primarily by the wall-to-tip distance and the wall angle but even more by the distance from the impact point in which it is measured. The semi-circle impact area was susceptible to wall angles and wall-to-tip distance variations, essential in the spray-air entrainment. No remarkable differences were found between the liquid and vapor phases for the free jet or the isothermal wall configuration. In contrast, some differences were obtained for the instrumented and thermoregulated wall, remarking the contribution of fuel evaporation caused by the wall temperature increase. Regarding the thermoregulated wall, the fuel and wall temperatures produced the most important peaks in terms of surface heat flux. A similar order of magnitude regarding the surface heat flux was found between the thermoregulated wall and infrared thermography experimental campaigns. The flash boiling appearance for the lower ambient back pressure and higher fuel temperature condition changed the spray morphology in terms of the width (spray angle), having significant repercussions over the R-parameter (which depends on the spray penetration) and in the number of liquid droplets present in the spray affecting both the light extinction profiles and the surface heat flux profiles., Esta tesis se ha desarrollado en el marco de una ayuda para la Formación de Personal Investigador (FPI) Subprograma 1 (PAID-01-19) financiada por la Universitat Politècnica de València.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Analyzing Independent LFMC Empirical Models in the Mid-Mediterranean Region of Spain Attending to Vegetation Types and Bioclimatic Zones

  • Arcos-Villacís, María Alicia
  • Edo-Botella, Roberto
  • Balaguer-Beser, Ángel|||0000-0003-0039-2641
  • Ruiz Fernández, Luis Ángel|||0000-0003-0073-7259
[EN] This paper presents empirical models developed through stepwise multiple linear regression to estimate the live fuel moisture content (LFMC) in a Mediterranean area. The models are based on LFMC data measured in 50 field plots, considering four groups with similar bioclimatic characteristics and vegetation types (trees and shrubs). We also applied a species-specific LFMC model for Rosmarinus officinalis in plots with this dominant species. Spectral indices extracted from Sentinel-2 images and their averages over the study time period in each plot with a spatial resolution of 10 m were used as predictors, together with interpolated meteorological, topographic, and seasonal variables. The models achieved adjusted R2 values ranging between 52.1% and 74.4%. Spatial and temporal variations of LFMC in shrub areas were represented on a map. The results highlight the feasibility of developing satellite-derived LFMC operational empirical models in areas with various vegetation types and taking into account bioclimatic zones. The adjustment of data through GAM (generalized additive models) is also addressed in this study. The different error metrics obtained reflect that these models provided a better fit (most adjusted R2 values ranged between 65% and 74.1%) than the linear models, due to GAMs being more versatile and suitable for addressing complex problems such as LFMC behavior., Ma Alicia Arcos gives thanks for the help received by the Universitat Politecnica de Valencia through a pre-doctoral contract financed in the call, PAID-01-19, subprogram 1. This research was funded by through a collaboration agreement between the company Red Electrica de Espana S.A.U. and the Universitat Politecnica de Valencia (2020-2023), as well as the research project PID2020-117808RB-C21 funded by MCIN/AEI/10.13039/501100011033 and by ESF Investing in your future.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Unleashing Technological Collaboration: AI, 5G, and Mobile Robotics for Industry 4.0 Advancements

  • Palacios Morocho, Maritza Elizabeth
[ES] La Industria 4.0 se enfrenta a importantes retos a la hora de perseguir la transformación digital y la eficiencia operativa. La creciente complejidad de los entornos industriales modernos lleva a la necesidad de desplegar tecnologías digitales y, sobre todo, la automatización de la Industria. Sin embargo, este camino hacia la innovación va acompañado de numerosos obstáculos, ya que el entorno cambia constantemente. Por lo tanto, para adaptarse a esta evolución, es necesario emplear planteamientos más flexibles. Estos planteamientos están estrechamente relacionados con el uso de la AI y RL, ya que surgen como soluciones clave para abordar los retos cruciales de la navegación cooperativa de agentes dentro de entornos dinámicos. Mientras tanto, los algoritmos RL se enfrentan a las complejidades que implica la transmisión y el procesamiento de grandes cantidades de datos, para hacer frente a este desafío, la tecnología 5G emerge como un habilitador clave para las soluciones de escenarios de problemas evolutivos. Entre las principales ventajas de la 5G están que ofrece una transmisión rápida y segura de grandes volúmenes de datos con una latencia mínima. Al ser la única tecnología hasta ahora capaz de ofrecer estas capacidades, 5G se convierte en un componente esencial para desplegar servicios en tiempo real como la navegación cooperativa. Además, otra ventaja es que proporciona la infraestructura necesaria para intercambios de datos robustos y contribuye a la eficiencia del sistema y a la seguridad de los datos en entornos industriales dinámicos. A la vista de lo anterior, es evidente que la complejidad de los entornos industriales conduce a la necesidad de proponer sistemas basados en nuevas tecnologías como las redes AI y 5G, ya que su combinación proporciona una potente sinergia. Además, aparte de abordar los retos identificados en la navegación cooperativa, también abre la puerta a la implementación de fábricas inteligentes, dando lugar a mayores niveles de automatización, seguridad y productividad en las operaciones industriales. Es importante destacar que la aplicación de técnicas de AI conlleva la necesidad de utilizar software de simulación para probar los algoritmos propuestos en entornos virtuales. Esto permite abordar cuestiones esenciales sobre la validez de los algoritmos, reducir los riesgos de daños en el hardware y, sobre todo, optimizar las soluciones propuestas. Con el fin de proporcionar una solución a los retos fundamentales en la automatización de fábricas, esta Tesis se centra en la integración de la robótica móvil en la nube, especialmente en el contexto de la Industria 4.0. También abarca la investigación de las capacidades de las redes 5G, la evaluación de la viabilidad de simuladores como ROS y Gazebo, y la fusión de datos de sensores y el diseño de algoritmos de planificación de trayectorias basados en RL. En otras palabras, esta Tesis no solo identifica y aborda los retos clave de la Industria 4.0, sino que también presenta soluciones innovadoras e hipótesis concretas para la investigación. Además, promueve la combinación de AI y 5G para desplegar servicios en tiempo real, como la navegación cooperativa. Así, aborda retos críticos y demuestra que la colaboración tecnológica redefine la eficiencia y la adaptabilidad en la industria moderna., [CA] La Indústria 4.0 s'enfronta a importants reptes a l'hora de perseguir la transformació digital i l'eficiència operativa. La creixent complexitat dels entorns industrials moderns porta a la necessitat de desplegar tecnologies digitals i, sobretot, l'automatització de la Indústria. No obstant això, este camí cap a la innovació va acompanyat de nombrosos obstacles, ja que l'entorn canvia constantment. Per tant, per a adaptar-se a esta evolució, és necessari emprar plantejaments més flexibles. Estos plantejaments estan estretament relacionats amb l'ús de l'AI i RL, ja que sorgixen com a solucions clau per a abordar els reptes crucials de la navegació cooperativa d'agents dins d'entorns dinàmics. Mentrestant, els algorismes RL s'enfronten a les complexitats que implica la transmissió i el processament de grans quantitats de dades, per a fer front a este desafiament, la tecnologia 5G emergix com un habilitador clau per a les solucions d'escenaris de problemes evolutius. Entre els principals avantatges de la 5G estan que oferix una transmissió ràpida i segura de grans volums de dades amb una latència mínima. A l'ésser l'única tecnologia fins ara capaç d'oferir estes capacitats, 5G es convertix en un component essencial per a desplegar servicis en temps real com la navegació cooperativa. A més, un altre avantatge és que proporciona la infraestructura necessària per a intercanvis de dades robustes i contribuïx a l'eficiència del sistema i a la seguretat de les dades en entorns industrials dinàmics. A la vista de l'anterior, és evident que la complexitat dels entorns industrials conduïx a la necessitat de proposar sistemes basats en noves tecnologies com les xarxes AI i 5G, ja que la seua combinació proporciona una potent sinergia. A més, a part d'abordar els reptes identificats en la navegació cooperativa, també obri la porta a la implementació de fabriques intel·ligents, donant lloc a majors nivells d'automatització, seguretat i productivitat en les operacions industrials. És important destacar que l'aplicació de tècniques d'AI comporta la necessitat d'utilitzar programari de simulació per a provar els algorismes proposats en entorns virtuals. Això permet abordar qüestions essencials sobre la validesa dels algorismes, reduir els riscos de dona'ns en el maquinari i, sobretot, optimitzar les solucions proposades. Amb la finalitat de proporcionar una solució als reptes fonamentals en l'automatització de fabriques, esta Tesi se centra en la integració de la robòtica mòbil en el núvol, especialment en el context de la Indústria 4.0. També abasta la investigació de les capacitats de les xarxes 5G, l'avaluació de la viabilitat de simuladors com ROS i Gazebo, i la fusió de dades de sensors i el disseny d'algorismes de planificació de trajectòries basats en RL. En altres paraules, esta Tesi no sols identifica i aborda els reptes clau de la Indústria 4.0, sinó que també presenta solucions innovadores i hipòtesis concretes per a la investigació. A més, promou la combinació d'AI i 5G per a desplegar servicis en temps real, com la navegació cooperativa. Així, aborda reptes crítics i demostra que la col·laboració tecnològica redefinix l'eficiència i l'adaptabilitat en la indústria moderna., [EN] Industry 4.0 faces significant challenges in pursuing digital transformation and operational efficiency. The increasing complexity of modern industrial environments leads to the need to deploy digital technologies and, above all, Industry automation. However, this path to innovation is accompanied by numerous obstacles, as the environment constantly changes. Therefore, to adapt to this evolution, it is necessary to employ more flexible approaches. These approaches are closely linked to the use of Artificial Intelligence (AI) and Reinforcement Learning (RL), as they emerge as pivotal solutions to address the crucial challenges of cooperative agent navigation within dynamic environments. Meanwhile, RL algorithms face the complexities involved in transmitting and processing large amounts of data. To address this challenge, Fifth Generation (5G) technology emerges as a key enabler for evolutionary problem scenario solutions. Among the main advantages of 5G is that it offers fast and secure transmission of large volumes of data with minimal latency. As the only technology so far capable of delivering these capabilities, 5G becomes an essential component for deploying real-time services such as cooperative navigation. Furthermore, another advantage is that it provides the necessary infrastructure for robust data exchanges and contributes to system efficiency and data security in dynamic industrial environments. In view of the above, it is clear that the complexity of industrial environments leads to the need to propose systems based on new technologies such as AI and 5G networks, as their combination provides a powerful synergy. Moreover, aside from tackling the challenges identified in cooperative navigation, it also opens the door to the implementation of smart factories, leading to higher levels of automation, safety, and productivity in industrial operations. It is important to note that the application of AI techniques entails the need to use simulation software to test the proposed algorithms in virtual environments. This makes it possible to address essential questions about the validity of the algorithms, reduce the risks of damage to the hardware, and, above all, optimize the proposed solutions. In order to provide a solution to the fundamental challenges in factory automation, this Thesis focuses on integrating mobile robotics in the cloud, especially in the context of Industry 4.0. It also covers the investigation of the capabilities of 5G networks, the evaluation of the feasibility of simulators such as Robot Operating System (ROS) and Gazebo, and the fusion of sensor data and the design of path planning algorithms based on RL. In other words, this Thesis not only identifies and addresses the key challenges of Industry 4.0 but also presents innovative solutions and concrete hypotheses for research. Furthermore, it promotes the combination of AI and 5G to deploy real-time services, such as cooperative navigation. Thus, it addresses critical challenges and demonstrates that technological collaboration redefines efficiency and adaptability in modern industry., This research was funded by the Research and Development Grants Program (PAID-01-19) of the Universitat Politècnica de València. The research stay of the author at Technischen Universit¨at Darmstadt (Germany) was funded by the Program of Grants for Student Mobility of doctoral students at the Universitat Politècnica de València in 2022 from Spain and by Erasmus+ Student Mobility for Traineeship 2022
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

A computational methodology to account for the liquid film thickness evolution in Direct Numerical Simulation of prefilming airblast atomization

  • Payri, Raul|||0000-0001-7428-5510
  • Salvador, Francisco Javier|||0000-0003-3269-2251
  • Carreres, Marcos|||0000-0001-6430-6613
  • Moreno-Montagud, C.
[EN] Prefilming airblast atomization is becoming widely used in current aero engines. Fundamental studies on the actual annular configuration of airblast atomizers are difficult to realize. For this reason, researchers have also focused on planar configurations. In this regard, the Karlsruhe Institute of Technology (KIT) developed a test rig to conduct experimental activities, conforming a large database with results for different working fluids and operating conditions. Such data allow two-phase flow modelers to validate their calculations concerning primary atomization on these devices. The present investigation proposes a Direct Numerical Simulation (DNS) study on the KIT planar configuration through the Volume of Fluid (VOF) method within the PARIS Simulator code. The novelty compared to DNS works reported in the literature resides in the use of a boundary condition that allows accounting not only for the gas inflow turbulence but also for the spatio-temporal evolution of the liquid film thickness at the DNS inlet and its related effect on turbulence. The proposed methodology requires computing precursor single-phase and two-phase flow Large-Eddy Simulations on the prefilmer flow, with the assumption that the flow between computational domains is one-way coupled. Results are compared to DNS that only account for a constant (both timewise and spanwise) liquid film thickness at the domain inlet, validating the full methodology workflow. The proposed methodology is shown to improve the qualitative description of the atomization mechanism, as the different stages of breakup (liquid accumulation behind the prefilmer edge, bag formation, bag breakup, ligament formation and ligament breakup) coexist spanwise for a given temporal snapshot. This implies a more continuous atomization than the one predicted by the constant film thickness case, which showed the same breakup stage to be present along the prefilmer span for a given instant and led to a more discretized set of atomization events. The proposed workflow allows quantifying the influence of the liquid film flow evolution above the prefilmer surface on primary breakup frequency and relevant atomization features., Research leading to these results has received funding from the Clean Sky 2 Joint Undertaking European Union's Horizon 2020 research and innovation programme through the ESTiMatE project, grant agreement 821418. The authors acknowledge PRACE for awarding access to computational resources on JOLIOT CURIE-AMD at GENCI@ CEA, France (proposal 2019204944). Computer resources at Marenostrum Supercomputer and the technical support provided by Barcelona Supercomputing Center (RES IM-2020-3-0018 and IM-2021-1-0010) in the frame of the Spanish Supercomputing Network is also thankfully acknowledged. Additionally, the support given to Mr. Carlos Moreno by Universitat Politecnica de Valencia, Spain through the "FPI Subprograma 2"grant within the "Programa de Apoyo para la Investigacion y Desarrollo (PAID-01-19)"is acknowledged. The authors must also thank Marco Crialesi and Wojciech Aniszewski for their technical advice on custom modifications on PARIS, and Johan Sundin for his implementation of the contact angle model. Help from Achille Schmitter, Hugo Martinez and Lucas Gonzalez processing the single-phase LES, two-phase LES, and DNS, respectively, is also appreciated.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

On the applicability of cold acoustic measurements to high-amplitude hot pulsating flows

  • Torregrosa, A. J.|||0000-0003-0933-1626
  • Piqueras, P.|||0000-0002-3767-0839
  • Sanchis, Enrique José|||0000-0002-6856-8992
  • Redondo-Navarro, Álvaro Rafael|||0000-0003-1668-1245
[EN] The experimental characterization of the acoustic characteristics of engine exhaust devices is usually carried out through measurements in cold conditions, due to the intrinsic difficulties associated with proper temperature control in an acoustic rig. While those measurements may be sufficiently indicative for the cold end of the exhaust (the silencing elements) their significance for the hot end (the aftertreatment system) is more doubtful, as a result of the high temperatures and, eventually, the higher amplitude of pressure waves acting on the system. In this paper, a direct assessment is provided on the significance of acoustic measurements in cold conditions for representing the actual behaviour of an aftertreatment system in a hot pulsating, engine-like flow. Making use of wave decomposition techniques, the measured characterization was convoluted with the hot-flow excitation and the device responses were directly compared. The results indicate that, while it is not possible to fully reproduce the behaviour observed in hot pulsating flow, the tendencies are reproduced, at least qualitatively. In particular, the effect of soot loading is fairly reproduced., This research has been supported by Grant PID2020114289RB-I00 funded by MCIN/AEI/https://doi.org/10.13039/501100011033.Alvaro Redondo is supported by Universitat Politecnica de Valencia through the Programa de Ayudas de Investigacion y Desarrollo (PAID-01-19) which grants his predoctoral contract.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Energy Efficiency Evaluation of Green Roofs as an Intervention Strategy in Residential Buildings in the Field of Spanish Climate

  • Garcia-Borràs, Júlia|||0000-0002-5470-0753
  • Lerma Elvira, Carlos|||0000-0003-0436-3725
  • Mas Tomas, Maria De Los Angeles|||0000-0002-0097-0598
  • Vercher Sanchis, José|||0000-0001-9855-4201
  • Gil Benso, Enrique|||0000-0002-6617-640X
[EN] The use of green roofs entails environmental, economic and social benefits as sustainable tools of architecture. They present proven benefits in the path towards carbon neutrality and the reduction of the consumption of energy resources, especially in the field of renovation and improvement of the thermal envelope. In Spain, the current climate crisis also implies a problem of water stress, so it is necessary to analyse in more detail the behaviour of self-sustaining green roofs in the different climatic and rainfall zones into which the territory is divided. Evapotranspiration is the main mechanism of heat dissipation in green roofs, but in this study, it is observed that in the case of self-sustaining roofs with limited water content, the greatest losses through evapotranspiration occur in climates with high temperatures and solar radiation, above cities with higher rainfall and colder climates. On the contrary, the greatest energy savings are obtained in this type of cold climate. Evapotranspiration in self-sustaining roofs is not the most determining factor for achieving energy savings. The design of the roof, the geometry and orientation of the building, as well as the cooling energy consumption, play a more determining role.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Characterization of the electropermeabilization induced by pulsed electric field (PEF) technology and its effect on the ultrasonic-assisted drying of yellow turnip

  • Llavata-Cabrero, Beatriz
  • Lyng, J.
  • Bedane, T. F.
  • Simal, S.
  • Carcel, J. A.|||0000-0002-3796-6146
[EN] Obtaining snacks from the drying of surplus vegetables is an alternative to reduce waste. A combination of pulsed electric field (PEF) pretreatments and ultrasonic-assisted (US) drying could significantly enhance the process, as this is the aim of this study. PEF pretreatments of yellow turnip significantly affected the cell disintegration index (CDI) and the water holding capacity (WHC): the more intense the PEF treatment, the greater the CDI and the lower the WHC. Both parameters, CDI and WHC, showed a high degree of correlation which indicated that WHC can be an alternative index to CDI to assess PEF effects on food matrices. Regarding yellow turnip drying (40¿°C), PEF pretreatments (CDI 0.25 and 0.75) and US application (20.5¿kW/m3) significantly accelerated the operation, but it was the combination of both technologies that provided the shortest process (CDI 0.75). PEF could generate changes in the food matrix which enhance the US effects on mass transfer., This work was supported from Agencia Estatal de Investigacion by the PID2019-106148RRC42 and PID2019-106148RRC43 grants funded by MCIN/AEI/10.13039/501100011033; the PID2022-136889OB-C22 grant funded by MCIN/AEI/10.13039/501100011033/ERDF, a way of making Europe, and the PhD grant of Beatriz Llavata from the Universitat Politecnica de Valencia [PAID-01-19].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Measuring the popularity of football players with Google Trends

  • Malagón-Selma, María del Pilar
  • Debón, A.|||0000-0002-5116-289X
  • Domenech, Josep|||0000-0002-7302-5810
[EN] Google Trends is a valuable tool for measuring popularity since it collects a large amount of information related to Google searches. However, Google Trends has been underused by sports analysts. This research proposes a novel method to calculate several popularity indicators for predicting players¿ market value. Google Trends was used to calculate six popularity indicators by requesting information about two football players simultaneously and creating popularity layers to compare players of unequal popularity. In addition, as the main idea is to obtain the popularity indicators of all players on the same scale, a cumulative conversion factor was used to rescale these indicators. The results show that the proposed popularity indicators are essential to predicting a player¿s market value. In addition, using the proposed popularity indicators decreases the transfer fee prediction error for three different models that are fitted to the data using the multiple linear regression, random forest, and gradient boosting machine methods. The popularity indicator Min, which is a robust reflection of the popularity that represents a player¿s popularity during the periods when they are less popular, is the most important popularity indicator, with a significant effect on the market value. This research provides practical guidance for developing and incorporating the proposed indicators, which could be applied in sports analytics and in any study in which popularity is relevant., P.M-S. Economic support through the FPI-UPV scholarship (PAID-01-19) to the Universitat Politecnica de Valencia. http://www.upv.es/entidades/VINV/indexc.html P.M-S, A.D., and J.D. Grant PID2019-107765RB-I00, funded by MCIN/AEI/10.13039/501100011033. The funders had no role in study design, data collection and analysis, decision to publish, or preparation of the manuscript.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Multipath Planning Acceleration Method With Double Deep R-Learning Based on a Genetic Algorithm

  • Palacios-Morocho, Maritza Elizabeth
  • Inca-Sánchez, Saúl Adrián
  • Monserrat del Río, Jose Francisco|||0000-0001-8664-6408
[EN] Autonomous navigation is a well-studied field in robotics requiring high standards of efficiency and reliability. Many studies focus on applying AI techniques to obtain a high-quality map, a precise localization, or improve the proposed trajectory to be followed by the agent. As traditional planning methods need a high-quality map to obtain optimal trajectories, this paper addresses the problem of multipath map-less planning, and proposes a novel multipath planning algorithm (Double Deep Reinforcement Learning - Enhanced Genetic (DDRL-EG)) for mobile robots in an unknown environment. It combines Double Deep Reinforcement Learning (DDRL) with Heuristic Knowledge (HK), Experience Replay (ER), Genetic Algorithm (GA), and Dynamic Programming (DP), allowing the agent to reach its target successfully without maps. In addition, it optimizes the training time and the chosen path in terms of time and distance to the target. A hybrid method is also used in which Semi-Uniform Distributed Exploration (SUDE) is employed to determine the probability that the action is decided based on directed knowledge, hybrid knowledge, or autonomous knowledge. The performance of DDRL-EG is compared with two other algorithms in two different environments. The results show that DDRL-EG is a more robust and powerful algorithm since with less training, it can provide much smoother and shorter trajectories to the target., The work of Elizabeth Palacios was supported by the Research andDevelopment Grants Program (PAID-01-19) of the Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Millimeter-wave Human Blockage Model Enhancements for Directional Antennas and Multiple Blockers

  • Prado-Alvarez, Danaisy|||0000-0003-3781-5951
  • Inca-Sánchez, Saúl Adrián
  • Martín-Sacristán, David|||0000-0002-7781-557X
  • Monserrat del Río, Jose Francisco|||0000-0001-8664-6408
[EN] The Third Generation Partnership Project (3GPP) has defined a blockage model as an add-on feature to the channel model used in its evaluations of the physical layer in the 0.5-100 GHz frequency range. This letter focuses on the human body blockage losses in the millimeter-wave band proposing: (i) a new criterion to place the diffraction points over the edges of the blockers that considers the precise position of the blocker with regard to the line-of-sight between the transmitter and the receiver, (ii) a specific criterion to determine which potential blockers, from a set of human bodies present in a certain scenario, should be considered effective blockers given the positions of a transmitter, a receiver, and those bodies, and (iii) a modification of the model to provide more accurate estimations in the case in which several blockers are closely located. The validity of our criteria and the accuracy improvement are confirmed by a set of measurements performed at 30 GHz with directional antennas and with multiple human blockers in different positions., The work of Danaisy Prado-Alvarez was supported by the H2020 Marie Curie Program, with Project Grant No. 766231 WAVECOMBE-ITN-2017. Part of this work has been performed in the framework of the H2020 project 5G-SMART co-funded by the EU. This was also supported by the Spanish Ministry of Science, Innovation and University under the project RTI2018-099880-B-C31. The associate editor coordinating the review of this letter and approving it for publication was J. Choi.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Real-world evaluation of a QCM-based biosensor for exhaled air

  • Juste-Dolz, Augusto Miguel|||0000-0003-4889-6419
  • Teixeira, William|||0000-0002-6729-9508
  • Pallás-Tamarit, Yeray|||0000-0002-1167-5631
  • Carrascosa Rubio, Javier|||0009-0003-4615-5278
  • Maquieira, Angel|||0000-0003-4641-4957
  • Carballido-Fernández, Mario
  • Morán-Porcar, Ángela
  • Redón-Badenas, María Ángeles
  • Pla-Roses, María Gracia
  • Tirado-Balaguer, María Dolores
  • Remolar-Quintana, María José
  • Ortiz-Carrera, Jon
  • Ibañez-Echevarría, Ethel
  • Giménez-Romero, David
[EN] The biosensor, named ¿virusmeter¿ in this study, integrates quartz crystal microbalance technology with an immune-functionalized chip to distinguish between symptomatic patients with respiratory diseases and healthy individuals by analyzing exhaled air samples. Renowned for its compact design, rapidity, and noninvasive nature, this device yields results within a 5-min timeframe. Evaluated under controlled conditions with 54 hospitalized symptomatic COVID-19 patients and 128 control subjects, the biosensor demonstrated good overall sensitivity (98.15%, 95% CI 90.1¿100.0) and specifcity (96.87%, 95% CI 92.2¿99.1). This proof-of-concept presents an innovative approach with signifcant potential for leveraging piezoelectric sensors to diagnose respiratory diseases., Open Access funding provided thanks to the CRUE-CSIC agreement with Springer Nature. A. J-D and W. T received fnancial support for the Ph.D. studies (FPI-UPV 2017 and PAID-01-19-06 grants, respectively). A.M awards grant DOGV no. 8815, May 19, 2020, pp. 16712 16726, from Generalitat Valenciana. D.G-R awards grant PI-2021-004 from the University of Valencia and INCLIVA|VLC Biomedical Research Institute.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Separation layers and their influence on green roof water storage

  • Garcia-Borràs, Júlia|||0000-0002-5470-0753
  • Mas Tomas, Maria De Los Angeles|||0000-0002-0097-0598
  • Lerma Elvira, Carlos|||0000-0003-0436-3725
  • Vercher Sanchis, José|||0000-0001-9855-4201
  • Gil Benso, Enrique|||0000-0002-6617-640X
[EN] This study deals with how adding separation layers to flat roofs improves their design, construction, and sustainability. Better understanding and use of these layers leads to increased durability, lower maintenance, and simpler execution, with potential for material reuse and performance enhancement. Currently, the optional nature of separation layers hinders the overall sustainability of roofing systems, so this research seeks to guide building professionals in selecting suitable separation layers for flat roofs, considering factors like location, function, material composition, and mass. Particularly, it examines the impact of Water Storage layers on self-sustaining green roofs, aiming to enhance thermal performance, especially when water is scarce. Results indicate that installing these layers significantly increases water retention below the drainage layer, primarily in extensive green roofs, where values rise by 17%. Water Storage layers also extend water availability after rainfall, raising maximum daily humidity levels inside the roof by up to 10% on the third day post-rainfall compared to green roofs without such a layer., This work was supported by Universitat Politecnica de Valencia: [grant no PAID-01-19-10].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Development and Characterization of Sustainable Composites from Bacterial Polyester Poly(3-Hydroxybutyrate-co-3-hydroxyhexanoate) and Almond Shell Flour by Reactive Extrusion with Oligomers of Lactic Acid

  • Ivorra-Martinez, Juan|||0000-0001-8968-4899
  • Boronat, Teodomiro|||0000-0002-2144-2874
  • Sanchez-Nacher, Lourdes|||0000-0002-8627-4576
  • Balart, Rafael|||0000-0001-5670-7126
  • Quiles-Carrillo, Luis|||0000-0001-8037-2215
  • Manuel-Mañogil, Jose
[EN] Eco-effcient Wood Plastic Composites (WPCs) have been obtained using poly(hydroxybutyrate-co-hexanoate) (PHBH) as the polymer matrix, and almond shell flour (ASF), a by-product from the agro-food industry, as filler/reinforcement. These WPCs were prepared with different amounts of lignocellulosic fillers (wt %), namely 10, 20 and 30. The mechanical characterization of these WPCs showed an important increase in their stiffness with increasing the wt % ASF content. In addition, lower tensile strength and impact strength were obtained. The field emission scanning electron microscopy (FESEM) study revealed the lack of continuity and poor adhesion among the PHBH-ASF interface. Even with the only addition of 10 wt % ASF, these green composites become highly brittle. Nevertheless, for real applications, the WPC with 30 wt % ASF is the most attracting material since it contributes to lowering the overall cost of the WPC and can be manufactured by injection moulding, but its properties are really compromised due to the lack of compatibility between the hydrophobic PHBH matrix and the hydrophilic lignocellulosic filler. To minimize this phenomenon, 10 and 20 phr (weight parts of OLA-Oligomeric Lactic Acid per one hundred weight parts of PHBH) were added to PHBH/ASF (30 wt % ASF) composites. Differential scanning calorimetry (DSC) suggested poor plasticization effect of OLA on PHBH-ASF composites. Nevertheless, the most important property OLA can provide to PHBH/ASF composites is somewhat compatibilization since some mechanical ductile properties are improved with OLA addition. The study by thermomechanical analysis (TMA), confirmed the increase of the coeffcient of linear thermal expansion (CLTE) with increasing OLA content. The dynamic mechanical characterization (DTMA), revealed higher storage modulus, E¿, with increasing ASF. Moreover, DTMA results confirmed poor plasticization of OLA on PHBH-ASF (30 wt % ASF) composites, but interesting compatibilization effects., This research work was funded by the Spanish Ministry of Science, Innovation, and Universities (MICIU) project number MAT2017-84909-C2-2-R. This work was supported by the POLISABIO program grant number (2019-A02). J. Ivorra-Martinez is the recipient of an FPI grant from Universitat Politècnica de València (PAID-2019). L. Quiles-Carrillo wants to thank GV for his FPI grant (ACIF/2016/182) and MECD for his FPU grant (FPU15/03812). Microscopy services at UPV are acknowledged for their help in collecting and analyzing FESEM images.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

In Vitro Photobehavior of Tyrosine Kinase Inhibitors in Solution and within Skin Cells

  • Ouardi el Hamidy, Meryem el
[ES] En las últimas décadas, la aprobación de los inhibidores de la tirosina quinasa (del inglés TKI) como una nueva clase de terapia dirigida ha mejorado la calidad de vida y las tasas de supervivencia de los pacientes con cáncer. Sin embargo, los efectos adversos asociados a éstos, como son las reacciones cutáneas, siguen siendo un desafío para la terapia controlada. De acuerdo con anteriores estudios fotofísicos y fotobiológicos de TKI realizados por el grupo de investigación, esta tesis sigue un enfoque multidisciplinar para investigar nuevos fármacos fotoactivos dentro de esta familia. En la etapa inicial, se seleccionaron cuatro TKI, gefitinib, axitinib, dasatinib y avapritinib, por su capacidad para absorber luz UVA y por su potencial fototóxico. Los estudios, tanto fotofísicos como fotobiológicos, se llevaron a cabo en estos fármacos. Gefitinib (GFT), un TKI con un cromóforo quinazolina, reveló cambios significativos en la fototoxicidad debido a modificaciones metabólicas en su estructura. Así, la desalquilación de la cadena lateral propoxi-morfolina (DMOR-GFT) presentó el valor más alto de factor de fotoirritación (PIF), aprox. 48, mientras que el metabolito desmetilado (DMT-GFT) mostró un valor de PIF mucho menor (~7), casi la mitad del valor de PIF del fármaco inalterado (~13). Por el contrario, el metabolito que presenta un grupo hidroxilo en lugar de flúor (DF-GFT) resultó no ser fototóxico. Notablemente, solo se confirmó que DMOR-GFT induce fotoperoxidación lipídica mediante un mecanismo oxidativo de Tipo I, basado en la escasa producción de oxígeno singlete y la eficiente desactivación del estado excitado triplete por un modelo lipídico. La fotooxidación de proteínas se evidenció en el caso de GFT y, en menor medida, en DMOR-GFT, pero resultó insignificante para DMT-GFT. Sin embargo, a diferencia de GFT, el daño al ADN inducido por el metabolito desmetilado no se reparó incluso después de varias horas. Axitinib (AXT), comercialmente disponible como el isómero (E)-AXT, tiende a fotoisomerizar a (Z)-AXT, especialmente en presencia de proteínas. Así, se revelaron dos mecanismos de fototoxicidad. En primer lugar, la conversión del (E)-AXT (no citotóxico) en el (Z)-AXT (citotóxico) tras irradiación. En segundo lugar, la fototoxicidad intrínseca exhibida por (Z)-AXT. Además, la fotooxidación de proteínas se atribuyó al isómero Z debido a la similitud en el contenido de carbonilo entre ambos isómeros y la alta afinidad del isómero Z por las proteínas. Finalmente, la fotogenotoxicidad solo se reveló mediante la detección de histonas ¿-H2AX. Dasatinib (DAS) es un TKI propuesto para el uso tópico en enfermedades cutáneas. Tras establecer un PIF inicial de 5, se confirmó la fototoxicidad de DAS en una emulsión oleo-acuosa en epidermis humana reconstruida (RhE), la cual se redujo sustancialmente al incorporar un filtro solar de amplio espectro. DAS presenta capacidad de generar tanto oxígeno singlete como radicales, desencadenando fotooxidación tanto en lípidos como en proteínas. Asimismo, se evidenció daño fotoinducido al ADN tanto mediante el ensayo cometa como la detección de ¿-H2AX. Avapritinib (AVP), un TKI de nueva aprobación, demostró ser un fármaco fototóxico con un valor de PIF de aproximadamente 11. Además, fue capaz de inducir tanto fotooxidación a las proteínas como daño en el ADN. En definitiva, el estudio de la toxicidad cutánea de los TKI en combinación con la luz solar se llevó a cabo mediante una exhaustiva evaluación de su fotocomportamiento tanto en disolución como en células de piel. El objetivo es proporcionar a los profesionales de la salud información actualizada sobre la foto(geno)toxicidad y alentarlos a evaluar e implementar estrategias de fotoprotección para los pacientes sometidos a la terapia basada en TKI., [CA] En les últimes dècades, l'aparició d'inhibidors de la tirosina cinasa (de l'anglès TKI) com una nova classe de teràpia dirigida ha millorat la qualitat de vida i les taxes de supervivència dels pacients amb càncer. No obstant això, els efectes adversos associats a aquests, com les reaccions cutànies, continuen sent un desafiament per a la teràpia controlada. D'acord amb estudis fotofísics i fotobiològics prèvis de TKI realitzats pel grup de recerca, esta tesi segueix un enfocament multidisciplinari per a investigar nous fàrmacs fotoactius dins d¿aquesta familia. En l'etapa inicial, es van seleccionar quatre TKI, gefitinib, axitinib, dasatinib i avapritinib, per la seua capacitat per absorbir llum en la regió UVA i el seu potencial fototòxic. Gefitinib (GFT), un TKI amb un cromòfor quinazolina, va experimentar canvis significatius en la fototoxicitat a causa de modificacions metabòliques en la seua estructura. La desalquilació de la cadena lateral propoxi-morfolina (DMOR-GFT) va presentar el valor més alt de factor de fotoirritació (PIF), aprox. 48, mentre que el metabòlit desmetilat (DMT-GFT) va mostrar un valor de PIF molt menor (~7), quasi la meitat del valor de PIF del fàrmac inalterat (aprox. 13). Al contrari, el metabòlit que presenta un grup hidroxil en lloc de fluor (DF-GFT) va resultar no ser fototòxic. Notablement, només es va confirmar que DMOR-GFT induïx fotoperoxidació lipídica mitjançant un mecanisme oxidatiu de Tipus I, basat en l'escassa producció d'oxigen singlet i l'eficient desactivació de l'estat excitat triplet per un model lipídic. La fotooxidació de proteïnes va ser evident per a GFT i, en menor mesura, per a DMOR-GFT, però va resultar insignificant per a DMT-GFT. No obstant això, a diferència de GFT, el dany a l'ADN induït pel metabòlit desmetilat no es va reparar fins i tot després de diverses hores. Axitinib (AXT), comercialment disponible com a (E)-AXT, tendeix a fotoisomeritzar a (Z)-AXT, especialment en presència de proteïnes. Així, es van revelar dos mecanismes de fototoxicitat. En primer lloc, la conversió de l'(E)-AXT (no citotòxic) en el (Z)-AXT (citotòxic) després d'irradiació. En segon lloc, la fototoxicitat intrínseca exhibida per (Z)-AXT. A més, la fotooxidació de proteïnes es va atribuir a l'isòmer Z a causa de la similitud en el contingut de carbonil entre ambdós isòmers i l'alta afinitat de l'isòmer Z per les proteïnes. Finalment, la fotogenotoxicitat només es va revelar mitjançant la detecció de histones ¿-H2AX. Dasatinib (DAS) és un TKI proposat per a l'ús tòpic en malalties cutànies. Després d'establir un PIF inicial de 5, es va confirmar la fototoxicitat de DAS en una emulsió oli-aquosa en epidermis humana reconstituïda (RhE), la qual es va reduir substancialment en incorporar un filtre solar d'ample espectre. DAS presenta capacitat de generar tant oxigen singlet com radicals, desencadenant la fotooxidació tant en lípids com en proteïnes. Així mateix, es va evidenciar mitjançant l'assaig cometa i la detecció d'H2AX dany fotoinduït a l'ADN. Avapritinib (AVP), un TKI de segona generació, va demostrar ser un fàrmac fototòxic amb un valor PIF d'aproximadament 11. A més, va ser capaç d'induir tant la fotooxidació a les proteïnes com induir dany en l'ADN. En definitiva, l'estudi de la toxicitat cutània dels TKI en combinació amb la radiació solar es va dur a terme mitjançant una exhaustiva avaluació del seu fotocomportament tant en dissolució como en cèl·lules de pell. L'objectiu és proporcionar als professionals de la salut informació actualitzada sobre foto(geno)toxicitat i fomentar l'avaluació e implementació d'estratègies de fotoprotecció per als pacients sotmesos a la teràpia basada en TKI., [EN] In recent decades, the emerge of tyrosine kinase inhibitors (TKIs) as a new class of targeted therapy has substantially enhanced the quality of life and survival rates for cancer patients. However, associated adverse effects, such as dermatological reactions, remain a challenge to sustained therapy. In light of our research group established insights into the photophysical and photobiological aspects of some TKIs, this thesis follows a similar multidisciplinary approach to investigate other photoactive drugs within the TKI family. In the initial stage, four TKIs, gefitinib, axitinib, dasatinib, and avapritinib, were selected based on their ability to absorb in the UVA region of the solar spectrum and their phototoxic potential. Consequently, photophysical and photobiological studies were conducted on these TKIs. Gefitinib (GFT) is a TKI with a quinazoline moiety, in which modifications resulting from metabolism significantly alter the phototoxicity potential. Dealkylation of the propoxy-morpholine side chain (DMOR-GFT) exhibited the highest photoirritant value (PIF), reaching approximately 48, while the demethylated metabolite (DMT-GFT) displayed much lower phototoxicity (PIF ~7), nearly half the PIF value of the parent drug (ca. 13). In contrast, replacing the fluorine substituent with OH (DF-GFT) resulted in the absence of phototoxic activity. Surprisingly, only DMOR-GFT was confirmed to induce lipid photoperoxidation which occurred through a Type I oxidative mechanism, based on the weak singlet oxygen production and the efficient quenching of the triplet excited state by a lipid model. Furthermore, protein photooxidation was evident for GFT and, to a lesser extent, for DMOR-GFT, but negligible for DMT-GFT. However, unlike the parent drug, DNA photodamage induced by the demethylated metabolite exhibited limited repair even after several hours. Axitinib (AXT), commercially available as (E)-AXT, showed a tendency for photoisomerization to (Z)-AXT, particularly within proteins. Thus, two phototoxicity mechanisms were unveiled. Firstly, the transformation of the initially non-cytotoxic (E)-AXT into the cytotoxic (Z)-AXT upon radiation. Secondly, the intrinsic phototoxicity exhibited by (Z)-AXT. Moreover, protein photooxidation was unequivocally attributed to the (Z)-isomer due to the similarity in carbonyl content between E/Z-isomers and the high protein affinity of the (Z)-isomer. Finally, the photogenotoxicity was only revealed through the detection of ¿-H2AX histone foci. Dasatinib (DAS) is a TKI suggested for topical treatment of dermatological diseases. Given this context and having determined a PIF value ca. 5, an evaluation of DAS phototoxicity in reconstructed human epidermis (RhE) was conducted. DAS formulated in an oil-in-water emulsion exhibited high phototoxicity, which was substantially reduced upon incorporating a broad-spectrum sunscreen. DAS, capable to generate both singlet oxygen and radicals, triggered photooxidation in both lipids and proteins. Similarly, DNA photodamage was evidenced through comet assay and H2AX foci detection. Avapritinib (AVP), a newly approved TKI, was proven to be a phototoxic drug with a PIF value ca. 11, which was highly photooxidative toward proteins and capable to induce DNA photodamage. All in all, the study of skin toxicity of TKIs in combination with sunlight was achieved through a comprehensive evaluation of their photobehavior both in solution and within skin cells. The aim is to provide healthcare professionals with updated information on photo(geno)toxicity and encourage them to assess and implement photoprotection strategies for patients undergoing TKI-based therapy., Agradezco a la Universitat Politècnica de València por la ayuda para la formación de doctores dentro del subprograma 1 (PAID-1- 2019) y al Ministerio de Ciencia, Innovación y Universidades por la ayuda para la formación del profesorado universitario (FPU19/00048). Ambas subvenciones resultaron fundamentales para la elaboración de mi tesis doctoral.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Biomimetic Growth of Hydroxyapatite in Hybrid Polycaprolactone/Graphene Oxide Ultra-Porous Scaffolds

  • Fuster-Gómez, Sandra|||0000-0001-5788-3981
  • Vidaurre, Ana|||0000-0003-3394-1176
  • Campillo-Fernández, Alberto J.|||0000-0002-2978-5994
  • Castilla Cortázar, María Isabel Cecilia
[EN] This paper reports the preparation and character-ization of hybrid scaffolds composed of polycaprolactone (PCL) and different graphene oxide (GO) amounts, intending to incorporate the intrinsic characteristics of their constituents, such as bioactivity and biocidal effect. These materials were fabricated by a solvent-casting/particulate leaching technique showing a bimodal porosity (macro and micro) that was around 90%. The highly interconnected scaffolds were immersed in a simulated body fluid, promoting the growth of a hydroxyapatite (HAp) layer, making them ideal candidates for bone tissue engineering. The growth kinetics of the HAp layer was influenced by the GO content, a remarkable result. Furthermore, as expected, the addition of GO neither significantly improves nor reduces the compressive modulus of PCL scaffolds. The thermal behavior of composites was investigated by differential scanning calorimetry, showing an increase in crystallinity as the addition of GO raised, which implies that GO nanosheets can act as seeds to induce the crystallization of PCL. The improved bioactivity was demonstrated by the deposition of an HAp layer on the surface of the scaffold with GO, especially with a 0.1% GO content., The authors are grateful for the support of the Spanish Ministry of Science, Innovation and Universities through (i) PID2021-126612OB-I00 and (ii) PID2019-106099RB-C41. Also, this research was supported by (iii) CIBER -Consorcio Centro de Investigación Biomédica en Red- (CB06/01/1026), Instituto de Salud Carlos III, Ministerio de Ciencia e Innovación and (iv) H2020 FET-OPEN grant 964562. FESEM images were taken by the authors at the Microscopy Service of the Universitat Politecnica &#768; de Valencia, &#768; whose advice is greatly appreciated.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Tesis doctoral (DoctoralThesis)

Novel Insights into the Viral Movement and Host Factors Interactions of Alfalfa Mosaic Virus and Biotechnological Applications of 30K Movement Proteins

  • Villar Álvarez, David
[ES] Los virus de plantas provocan importantes pérdidas en el sector agrícola, por lo que comprender su biología es clave para desarrollar estrategias de control. Un aspecto crucial en las infecciones virales es el movimiento sistémico, que permite la propagación del virus dentro de la planta. Para profundizar en los aspectos del transporte sistémico, se realizó un experimento de evolución compensatoria con una construcción derivada del RNA3 de AMV defectuosa en el movimiento sistémico. En este experimento, ciertos linajes virales recuperaron la capacidad de moverse sistémicamente tras varios pases. En estos linajes, se observaron mutaciones en la región no traducible 5' (5'UTR). Los 5'UTR evolucionados poseían una menor afinidad por la proteína de cubierta (CP), y generaban una menor acumulación de partículas virales. Además, los 5'UTR evolucionados permitieron el movimiento sistémico de versiones del RNA3 con una CP mutada, incapaz de formar partículas virales, lo que sugiere que la encapsidación no es esencial para el movimiento sistémico. El silenciamiento génico inducido por virus (VIGS) es una herramienta fundamental para estudiar la funcionalidad génica en plantas. En esta tesis se desarrolló un nuevo enfoque para generar vectores VIGS modificando MPs de la familia 30K. Este método se probó en AMV, el virus del mosaico del pepino (CMV) y el virus del mosaico del tabaco (TMV); en plantas de Nicotiana tabacum y N. benthamiana. Los ensayos permitieron establecer una correlación entre el tamaño del inserto y la eficacia del silenciamiento: los insertos de 45-54 pb consiguieron silenciar el gen de la fitoeno desaturasa (PDS) en un 75-90 %, mientras que los insertos más pequeños (21-39 pb) mostraron un silenciamiento del 45 %. También se detectó una relación inversa entre la eficiencia del silenciamiento y la encapsidación viral, resaltando la importancia de la encapsidación en el diseño de vectores VIGS. Otro aspecto clave de la infección es la interacción entre proteínas virales y factores del hospedador. En esta tesis se empleó una estrategia novedosa para identificar factores del hospedador que interaccionan con MPs de la familia 30K. Mediante esta estrategia se identificaron 121 posibles interactores de la MP de AMV en N. tabacum, validando cinco mediante ensayos BiFC: una histona 2 B (H2B), una actina, una proteína 14-3-3A, un factor de iniciación eucariota 4A (eIF4A) y una peroxidasa. Los resultados obtenidos sugieren que algunos de estos factores podrían formar parte de complejos multiproteicos asociados a la MP de AMV, mientras que otros interactúan también con otras MPs de la familia 30K, evidenciando la existencia de interactores comunes en el grupo 30K. La proteína H2B se seleccionó para realizar un análisis más profundo. Los resultados mostraron que la H2B interacciona con MPs de la familia 30K y del doble bloque genético, siendo las regiones N-terminales clave en esta interacción. El silenciamiento del gen H2B.1 en Nicotiana benthamiana redujo la acumulación viral y aumentó las hormonas de defensa, como el ácido salicílico (SA) y el ácido abscísico (ABA). La interrupción de la interacción MP-H2B mediante ensayos de competencia también disminuyó los títulos virales, indicando que esta interacción es esencial para la infección. Además, las infecciones virales alteraron la localización nuclear de H2B y la expresión de variantes específicas de H2B, lo que sugiere que ciertas variantes H2B desempeñan roles específicos en la respuesta frente a virus. En conjunto, esta tesis aporta conocimientos relevantes sobre el movimiento sistémico viral, las interacciones entre MPs de la familia 30K y factores del huésped, además de presentar una nueva estrategia para el desarrollo de vectores VIGS. Estos hallazgos podrían tener distintas implicaciones tanto en investigación básica como en investigación aplicada en el sector agrícola, lo que, en última instancia, podría contribuir a la obtención de plantas resistentes a virus., [CA] Els virus de plantes causen pèrdues significatives en l'agricultura. Comprendre els seus mecanismes moleculars és essencial per a desenrotllar estratègies de control efectives. Un aspecte clau de la infecció viral és el moviment sistèmic, que permet la disseminació del virus dins de la planta i la seua propagació a altres hostes. Per a aprofundir en este aspecte, es va realitzar un experiment d'evolució compensatòria amb un RNA 3 de AMV defectuós en el moviment sistèmic però capaç de moure's de cèl·lula a cèl·lula. Alguns llinatges virals van recuperar la capacitat de transport sistèmic després de diverses passades. L'anàlisi va revelar mutacions en la regió 5' UTR, que reduïen l'afinitat per la proteïna de coberta (CP) i disminuïen l'acumulació de partícules virals. A més, estes mutacions van permetre el moviment sistèmic fins i tot en una versió del RNA 3 amb una CP mutada, suggerint que la formació de virions no és essencial per al transport a llarga distància. També es va observar un augment del moviment sistèmic en variants de AMV amb MPs d'altres virus de la família 30K, reforçant la hipòtesi que l'encapsidació no és un requisit absolut per a este procés. El silenciament gènic induït per virus (VIGS) és una eina potent per a l'estudi funcional de gens en plantes d'importància agrícola. En esta tesi es va desenrotllar una estratègia nova per a generar vectors VIGS modificant les MPs de la família 30K, que inclou més de 500 espècies víriques que infecten cultius rellevants. La incorporació de seqüències heteròlogues en les MPs es va provar en AMV, el virus del mosaic del cogombre (CMV) i el virus del mosaic del tabac (TMV). Els assajos en Nicotiana tabacum i N. benthamiana van demostrar que insercions de 45-54 pb en les MPs aconseguien un silenciament del gen PDS del 75-90 %, amb un fenotip clar d'emblanquiment. Insercions més curtes (21-39 pb) van mostrar una eficàcia menor (¿45 %), mentre que fragments inferiors a 21 pb no induïen cap silenciament. A més, es va trobar una relació inversa entre l'eficàcia del silenciament i la capacitat d'encapsidació del virus, ressaltant la influència d'este procés en el disseny de vectors VIGS. Un altre aspecte fonamental de la infecció viral és la interacció entre factors de l'hoste i proteïnes víriques. Mitjançant una estratègia basada en immunoprecipitació durant la infecció natural en N. tabacum, es van identificar 121 possibles interactors de la MP d'AMV. D'estos, cinc van ser validats per complementació bimolecular de fluorescència (BiFC): H2B, actina, 14-3-3A, eIF4A i POX. L'anàlisi detallada d'H2B va mostrar que esta histona interacciona amb MPs de diversos gèneres vírics, incloent-hi la família 30K i les MPs del doble bloc genètic. El mapatge de la interacció va revelar que les regions N-terminals de totes dues proteïnes són essencials. El silenciament del gen H2B.1 en N. benthamiana va reduir els títols virals i va incrementar els nivells d'hormones defensives com SA i ABA. A més, la interrupció de la interacció MP-H2B mitjançant assajos de competència va provocar una reducció addicional de la càrrega viral, destacant la seua rellevància en la patogènesi viral. També es va observar que les infeccions víriques alteraven la localització nuclear d'H2B i l'expressió de variants específiques, suggerint que algunes podrien tindre rols concrets en la resposta de la planta als virus. En conjunt, esta tesi proporciona noves dades sobre el moviment sistèmic viral i la interacció entre MPs de la família 30K i factors de l'hoste. A més, presenta una estratègia innovadora per al desenrotllament de vectors VIGS mitjançant la modificació de les MPs. Estes troballes podrien tindre aplicacions tant en investigació bàsica com en biotecnologia agrícola, contribuint al desenrotllament de cultius amb major resistència als virus., [EN] Viruses cause substantial losses in agricultural crops, making it essential to understand their biology for developing control strategies and biotechnological tools. One key aspect of plant virus infection is systemic movement through vascular tissues, but many details remain unclear. In alfalfa mosaic virus (AMV), the coat protein (CP) plays a major role in long-distance transport, yet its precise function remains unknown. To investigate this, a compensatory evolution experiment was conducted using an AMV RNA3 construct defective in systemic transport. After several passages, some viral lineages regained the ability for systemic movement, revealing mutations in the 5' untranslated region (5'UTR). These evolved 5'UTRs had reduced CP affinity and lower virus particle accumulation, but still enabled systemic movement, even when CP was mutated and unable to form particles, indicating that encapsidation is not essential for systemic transport. Additionally, movement proteins (MPs) from the 30K family enhanced systemic transport in the evolved AMV constructs. Virus-induced gene silencing (VIGS) is a powerful tool for functional studies in agriculturally important crops. This thesis developed a novel VIGS approach using viruses with 30K family MPs as vectors. The 30K MP family includes 20 viral genera and over 500 species, which infect most major crops. MPs from AMV, cucumber mosaic virus (CMV), and tobacco mosaic virus (TMV) were modified to incorporate target gene sequences. In Nicotiana tabacum and N. benthamiana, insert sizes correlated with silencing efficiency: 45-54 bp inserts achieved 75-90% silencing of the phytoene desaturase (PDS) gene, while 21-39 bp fragments resulted in 45% silencing without visible phenotypes. Inserts shorter than 21 bp did not induce silencing. Notably, silencing efficiency was inversely correlated with viral encapsidation efficiency, emphasizing its importance in VIGS vector design. Host factors interacting with viral proteins are another crucial aspect of infection. This study employed a novel strategy to identify host factors in N. tabacum that interact with 30K family MPs. For this purpose, tags were added to the AMV MP coding sequence without affecting its functionality, enabling the identification of 121 potential interactors through immunoprecipitation. Five candidates¿histone H2B, actin, 14-3-3A protein, eukaryotic initiation factor 4A (eIF4A), and a peroxidase (POX)¿were validated using bimolecular fluorescence complementation (BiFC). Furthermore, some of these factors appeared to form protein complexes with AMV MP, while others interacted with MPs from different 30K viruses, suggesting shared host interactors among this MP family. H2B was further analyzed due to its emerging role in plant-pathogen interactions. H2B was found to interact with MPs from various viral genera, including 30K MPs and double gene block MPs. Mapping experiments revealed that AMV MP and H2B interact via their N-terminal regions. Silencing the H2B.1 gene in N. benthamiana significantly reduced viral titers and increased levels of defense-related hormones, such as salicylic acid (SA) and abscisic acid (ABA). Disrupting the MP-H2B interaction further decreased viral accumulation, underscoring its importance in infection. Viral infections also altered H2B's nuclear localization and the expression patterns of specific H2B variants, suggesting distinct roles in the host response. Collectively, this thesis advances our understanding of viral movement mechanisms, identifies novel host factors interacting with 30K family MPs, and refines a strategy for using modified 30K MPs as VIGS vectors. These findings have broad implications for both basic research and agricultural applications by contributing to the development of broad-spectrum resistance strategies against RNA viruses., David Villar Álvarez ha disfrutado de un contrato predoctoral para la formación de doctores otorgado por la Universitat Politècnica de València (Subprograma 1, PAID-01-19). El trabajo de investigación llevado a cabo en esta tesis doctoral ha sido financiado por los proyectos de investigación PID2019-103998GB-I00 y PID2020-115571RB-I00 del Ministerio de Ciencia, Innovación y Universidades; y el proyecto de investigación PROMETEO/CIPROM/2022/031 de la Generaliatat Valenciana.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

PEF pre-treatment and ultrasound-assisted drying at different temperatures as a stabilizing method for the up-cycling of kiwifruit: Effect on drying kinetics and final quality

  • Llavata-Cabrero, Beatriz
  • Collazos-Escobar, Gentil Andres|||0000-0002-0659-8897
  • Garcia-Perez, J.V.|||0000-0002-9993-4246
  • Carcel, J. A.|||0000-0002-3796-6146
[EN] The drying of food by-products, such as kiwifruit discards and surpluses, constitutes an interesting option as a means of stabilizing them for later use. This study assesses the combined influence of the drying temperature (40¿70 °C), pulsed electric field (PEF) pretreatment (0¿5000 V) and ultrasound (US; 0¿50 W) application during the drying of kiwifruit. The increase in temperature, the use of PEF pretreatment or the US application during drying accelerated the process, but it was the combination of the three which led to the highest values of the effective diffusivity and the mass transfer coefficient. Over the range of different conditions studied, the functional and antioxidant properties of dried kiwifruit were not significantly affected, while the color presented some differences, mainly related to the L* and a* coordinates. Therefore, the combination of temperature, PEF and US allowed the processing time to be shortened without significantly affecting the final quality of kiwifruit., This work was supported by the PID2019-106148RRC42 grant funded by MCIN/AEI/10.13039/501100011033, PID2022-136889OB-C22 grant founded by MCIN/AEI/10.13039/501100011033/ERDF a way of making Europe, PhD grant of Beatriz Llavata from the Universitat Politècnica de València (PAID-01-19) and PhD grant of Gentil A. Collazos-Escobar from the State Training Subprogram of the State Plan for Scientific and Technical Research and Innovation 2017-2020, in conjunction with the European Social Fund (PRE2020-092255).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Capítulo o parte de un libro (BookPart)

Modelos empíricos de predicción del contenido de humedad del combustible vivo mediante índices espectrales de Sentinel-2 y datos meteorológicos, Empirical models for predicting live fuel moisture content using Sentinel-2 spectral indices and meteorological data

  • Arcos, María
  • Balaguer-Beser, Ángel|||0000-0003-0039-2641
  • Ruiz Fernández, Luis Ángel|||0000-0003-0073-7259
[EN] The water content of the vegetation affects the flammability of the vegetation and fire behavior. A standard measure of this parameter is the live fuel moisture content (LFMC), calculated as the percentage of humidity of the vegetation relative to its dry weight. The aim of this work was to predict LFMC values of Rosmarinus officinalis in forest areas of the Valencian Community (Spain) using spectral indices obtained from Sentinel-2 satellite images and meteorological data. For this, LFMC values of this species were obtained from field samples collected biweekly from June to October in years 2019 and 2020 in three forest plots in the province of Valencia (Spain). The meteorological data (precipitation, temperature, relative humidity and wind speed) were obtained from observatories of the State Meteorological Agency (AEMET) of Spain. Multiple linear regression models were applied to estimate LFMC, using as predictor variables different spectral indices generated from Sentinel-2 images, calculated using Google Earth Engine and R programming. The results obtained using smoothed spectral data with the Savitzky-Golay filter were compared with data without such smoothing, also considering the differential contribution of the meteorological variables in each of the interpolated dates for each plot with data from the study area., [ES] El contenido de agua de la vegetación afecta a la inflamabilidad de la vegetación y al comportamiento del fuego. Una medida estándar de este parámetro es la humedad del combustible vivo (HCV), calculada como el porcentaje de humedad de la vegetación respecto a su peso seco. El objetivo de este trabajo ha sido predecir los valores de HCV de Rosmarinus officinalis en zonas forestales de la Comunitat Valenciana (España) utilizando índices espectrales obtenidos a partir de imágenes de los satélites Sentinel-2 y datos meteorológicos. Para ello, se obtuvieron valores de HCV de dicha especie en muestras tomadas quincenalmente entre los meses desde junio hasta octubre de los años 2019 y 2020 en tres parcelas forestales en la provincia de Valencia (España). Los datos meteorológicos (precipitación, temperatura, humedad relativa y velocidad del viento) se obtuvieron a partir de observatorios de la Agencia Estatal de Meteorología (AEMET) de España. Se aplicaron modelos de regresión lineal múltiple para estimar los valores de HCV, usando como variables predictoras distintos índices espectrales generados a partir de imágenes Sentinel-2, calculados usando Google Earth Engine y programación en R. Se compararon los resultados obtenidos empleando datos espectrales suavizados con el filtro Savitzky-Golay y datos sin suavizar, considerando además el aporte diferencial de las variables meteorológicas en cada una de las fechas interpoladas para cada parcela con datos de campo., Mª Alicia Arcos agradece la ayuda recibida por la Universitat Politècnica de València mediante un contrato predoctoral financiado en la convocatoria, PAID-01-19, subprograma 1. Este trabajo ha sido financiado a través de un convenio de colaboración entre la empresa Red Eléctrica de España S.A.U. y la Universitat Politècnica de València (2020-2023). Los autores agradecen a la Empresa Pública VAERSA y a la Direcció General de Prevenció d’Incendis Forestals de la Generalitat Valenciana por proporcionar los datos de medición de HCV en campo y los datos meteorológicos a través de la AEMET.