Skip to main content

SINTERIZACION EN FRIO DE MATERIALES FERROELECTRICOS, FERROMAGNETICOS Y COMPOSITES

PID2020-112659RB-I00

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos de I+D+i (Generación de Conocimiento y Retos Investigación)
Call year 2020
State Plan 2017-2020 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre UNIVERSITAT JAUME I DE CASTELLO

Resultados relacionados

Resultados totales (Incluyendo duplicados): 10
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Impact of Li1.3Al0.3Ti1.7(PO4)3 content and particle size on the electrochemical properties and stability of polymer-based solid electrolytes for lithium batteries

  • Simon, Sonia
  • Ferrer-Nicomedes, Sergio
  • Garcia-Belmonte, Germa
  • Barba-Juan, Antonio
  • Vicente-Agut, Nuria
  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
[EN] This work addresses the current limitations of standard composite solid electrolyte membranes through a systematic optimization of the LATP Li1.3Al0.3Ti1.7(PO4)3 wt fraction and rigorous particle size control via selective milling. By precisely integrating these calibrated ceramic particles within a ternary PVDF-HFP/PEO matrix, the resulting configuration establishes a highly balanced framework for advanced lithium-ion battery applications. The optimal composition, designated CSE2H (26 wt% LATP with particle size d50 approximate to 0.875 mu m), exhibits exceptional electrical properties: minimum activation energy (0.138 eV), maximum ionic conductivity (1.12 & sdot;10- 4 S cm- 1 at 30 degrees C and 6.33 & sdot;10- 4 S cm- 1 at 70 degrees C), and stable electrochemical operation within the voltage range 2.5-4.2 V vs. Li+/Li, LFP-cell operating conditions. Electrochemical impedance spectroscopy reveals low interfacial resistance, while chronoamperometry measurements yield a lithium-ion transference number of 0.48, indicating efficient ion transport. Galvanostatic cycling experiments confirm high coulombic efficiency (98%) and good capacity retention: initial capacity of 147 mAh g- 1 LFP at 0.5C stabilizing at 77.58 mAh g- 1 LFP after 200 cycles, with specific discharge capacity of 127.2 mAh g- 1 LFP at 2C. Concurrently, these integrated results establish that this 26 wt% LATP baseline configuration successfully balances interfacial compatibility with competitive electrochemical properties, presenting a highly viable pathway for targeted solidstate battery development., A. B.-J. and G. G.-B. have received funding from Generalitat Valenciana under the Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030) and CIPROM/2024/91. A. B.-J. and N. V.-A. acknowledge the financial support received from projects PID2020-112659RB-I00 and PID2024-158590OB-I00, funded by MICIU/AEI/10.13039/501100011033. N. V.-A. acknowledges support from Universitat Jaume I under project UJI/2023/016. S. F.-N. thank Generalitat Valenciana for the FPI Fellowship Program (grant numbers CIACIF/2021/050). A. M.-S. acknowledge the financial support received from projects PAID-06-25 and PAID-10-24, funded by Universitat Politecnica de Valencia.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo de revisión (ReviewArticle)

Sintering science meets sustainability: a review of cold sintering process in solid-state electrolytes

  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Barba Juan, Antonio
[EN] The global push for deep decarbonization by 2050 has accelerated energy storage development to address power intermittency. This review covers ceramic- and polymer-in-ceramic solid-state electrolytes obtained via the cold sintering process, which enables higher energy density and safety by replacing liquid electrolytes and supporting lithium-metal anodes. Cold sintering, at temperatures below 300 ¿C, provides fast densification with low environmental impact compared to traditional high-temperature sintering. It affects microstructure, phase stability, and ionic transport. Important applications include lithium and sodium solid electrolytes with notable density and conductivity. Challenges remain in material optimization, scaling, and integrating multifunctional designs for sustainable, high-performance batteries., A.B.-J. acknowledge the financial support from Generalitat Valenciana under Pla Complementari Programa de Materials Avanc¿ats , 2022 [grant number MFA/2022/030], and A.B.-J. also acknowledges Ministerio de Ciencia e Innovacion; (Spain) [grant number MCIN/AEI/10.13039/501100011033]. Am-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program [grant numbers ACIF/2021/294 and CIACIF/2021/050]. N.V.-A. thanks the financial support from UJI [grant UJI-2023-16].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fine-tuning the microstructure for improved performance in cold-sintered Li1. 3Al0. 3Ti1. 7 (PO4) 3 composite solid electrolytes

  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Barba-Juan, Antonio
  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
[EN] Solid-state electrolytes (SSE) are one of the fundamental components of the upcoming generation of batteries since they increase the operational safety and efficiency. In this work, composite solid electrolytes (CSE) based on Li1.3Al0.3Ti1.7(PO4)3 and a (PEO2-LiTFSI) polymer matrix are obtained via the pioneering Cold Sintering Process (CSP), with a drastic reduction of the conventional sintering temperature. The CSP is performed at only 150 °C and 700 MPa, for 90 min of sintering time, by using a 3m acetic acid solution as the transient liquid phase (TLP). Here, the effect of the LATP particle size (d50) is studied to tailor the final microstructure, which enables the fine-tuning of the ultimate electrical properties of the electrolyte. An optimum d50 of 0.415 ¿m produces CSEs with 91 % of relative density, an ionic conductivity of 0.169 mS/cm, activation energy of 0.293 eV and electrical stability under 0.1 mA/cm2, thus leading to competitive properties., A.B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion (Spain) (grant number MCIN/AEI/10.13039/501100011033) and Generalitat Valenciana under Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030) . A.M.-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program (grant numbers ACIF/2020/294 and ACIF/2021/050) . N.V.-A. thanks the financial support from UJI (grant UJI-2023-16) . The authors also acknowledge SCIC from UJI and Celgard for supplying the separator membranes.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Densification and performance optimization of NaSICON solid electrolytes via a low-temperature cold sintering process with sodium ionic salt doping

  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Barba-Juan, Antonio
  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
[EN] Sodium-ion batteries (SIBs) have emerged as a sustainable alternative to lithium-ion systems, offering cost-effective and environmentally friendly energy storage solutions. Solid-state electrolytes (SSEs), particularly NaSICON-type materials such as Na3.4Zr1.9Zn0.1Si2.2P0.8O12 (NZZSP) studied here, are critical for enhancing the safety and stability of SIBs. However, conventional high-temperature sintering methods for fabricating these electrolytes are energy-intensive and environmentally impactful. In this work, we employed the Cold Sintering Process (CSP) to densify NZZSP at a low temperature of 150 °C under 720 MPa with the aid of a transient liquid phase (TLP), achieving a sustainable electrolyte production with competitive performance. The effects of milling time and two different TLP media were evaluated, with 3 M acetic acid solution (HAc) being more effective than 25 mM sodium hydroxide solution (NaOH) in preserving particle integrity and yielding higher ionic conductivity (0.50 mS cm¿1). Doping with NaPF6 and NaTFSI further enhanced performance, with 20% NaPF6-doped samples achieving the highest densification (94.3%) and conductivity (0.80 mS cm¿1). Optimized 2 hour-milled, 20% NaPF6 electrolytes demonstrated suitable cycling stability in symmetric cells (over 500 hours) and specific capacity in half cells, with Na metal and Na3V2(PO4)3 (NVP) as electrodes, of about 85 mA h gNVP ¿1 at C/2 and over 100 mA h gNVP ¿1 at C/10 after cycling at multiple rates. These results underscore the potential of the CSP as a sustainable, low-temperature alternative for fabricating high-performance solid-state electrolytes for application in all solid-state sodium batteries., This work has received funding from Generalitat Valenciana under Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030). A. B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion (Spain) grant number. MCIN/AEI/10.13039/501100011033. N. V.-A. acknowledges the support for the research from Universitat Jaume I under the project number UJI/2023/016. A. M.-S. and S. F.-N. thank Generalitat Valenciana for the FPI Fellowship Program (grant numbers ACIF/2021/294 and CIACIF/2021/050).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Heating-time independent Densification of LATP via Cold Sintering Process

  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
  • Hérisson de Beauvoir, Thomas
  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Estournès, Claude
  • Barba Juan, Antonio
[EN] The Cold Sintering Process has been used to sinter Li1.3Al0.3Ti1.7(PO4)3 powder (LATP) initially mixed with 15 wt.% of a solution of acetic acid 3 m as Transient Liquid Phase (TLP). The effect of variables such as green density, heating rate, sintering temperature, dwell time and the operating pressure on the densification of LATP via CSP has been thoroughly analysed. The operating pressure shows no effect on the green density above 450 MPa. The heating rates, thus the heating time, do not modify the densification behavior of LATP Solid-State Electrolytes (SSEs) but a decomposition reaction takes place at temperatures above 180 ºC. This reaction depends on the TLP amount still present in the pores, and at higher pressures (P>450 MPa) this decomposition effect on densification is reduced as the pore volume becomes smaller. For the first time in the CSP, a linear dependence of relative density on temperature is demonstrated., This work has received funding from Generalitat Valenciana under Pla Complementari Programa de Materials Avançats , 2022 (grant number MFA/2022/030). A.B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion (Spain) grant number. MCIN/ AEI/10.13039/501100011033. N.V.-A. acknowledges the support for the research from Universitat Jaume I under the project number UJI/ 2023/016. A.M.-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program (grant numbers ACIF/2021/294 and CIACIF/2021/ 050). A.M.-S. thanks Generalitat Valenciana through its Internship Fellowship Program for PhD students (grant number CIBEPF/2023/137).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Hydroflux-assisted cold sintering: eutectic mixtures for boosting ionic conductivity in LATP solid-state electrolytes

  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Barba Juan, Antonio
[EN] Superior electrical properties have been achieved for a Li1.3Al0.3Ti1.7(PO4)3 (LATP) solid-state electrolyte (SSE) by using the novel hydroflux-assisted cold sintering process (HACSP) at 400 MPa, 200 °C and 90 minutes of sintering time. The use of the eutectic LiOH:LiNO3 mixture, with 20 wt% content, as an hydroflux to assist the CSP has allowed to obtain a total ionic conductivity of 1.51 × 10¿4 S cm¿1 and an activation energy of 0.366 eV. Using water to better distribute the hydroflux along the LATP structure was found to be critical to the homogeneity and properties of the sample., This work has received funding from Generalitat Valenciana under Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030). A. B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion (Spain) grant number. MCIN/AEI/10.13039/501100011033. N. V.-A. acknowledges the support for the research from Universitat Jaume I under the project number UJI/2023/016. A. M.-S. and S. F.-N. thank Generalitat Valenciana for the FPI Fellowship Program (grant numbers ACIF/2021/294 and ACIF/2021/050).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Pressure-Driven Structural Distortion in Cold Sintered LiFePO4|Li1.3Al0.3Ti1.7(PO4)3 Composite Solid Electrolyte Bilayers

  • Ferrer-Nicomedes, Sergio
  • Zarrabeitia, Maider
  • Bresser, Dominic
  • García-Belmonte, Germà
  • Vicente-Agut, Nuria
  • Barba, Antonio
  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
[EN] The pressure applied during the fabrication of LiFePO4-composite solid electrolyte bilayers via Cold Sintering Process (CSP) is known to influence their electrochemical performance and structural integrity. In a previous work, the authors have reported that bilayers sintered at high pressure (720 MPa) achieve high densification, but exhibit rapid capacity fading and poorer cycling stability compared to those processed at lower pressures (300 MPa). This study employs the galvanostatic intermittent titration technique (GITT), operando X-ray diffraction (XRD), and ex situ X-ray photoelectron spectroscopy (XPS) to elucidate the underlying mechanisms hindering the performance in high-pressure bilayers. GITT reveals larger and progressively increasing overpotentials and internal resistances, as well as irregular ion diffusion in high-pressure bilayers, suggesting altered lithiation kinetics. Operando XRD identifies irreversible phase transformations alongside accumulation of inactive FePO4 species, with XPS confirming the presence of oxidized iron (Fe3+) in the discharged cathodes sintered at high pressure. Notably, lattice distortions in the b and c axes-key lithium diffusion pathways in the olivine structure-are more pronounced at 720 MPa, indicating pressure-induced crystalline deformation modifies the energy barrier for lithium ion migration. Conversely, bilayers sintered at 300 MPa maintain stable structural and kinetic behavior, enabling reversible cycling and superior performance. These findings underscore the delicate balance required in CSP pressure to optimize densification of multi-component structures without compromising electrode functionality, guiding the design of robust solid-state bilayers and multilayers for next-generation battery technologies., This work has received funding from Generalitat Valenciana under Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030). A. B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion (Spain) grant number. MCIN/AEI/10.13039/501100011033. N. V.-A. acknowledges the support for the research from Universitat Jaume I under the project number UJI/2023/016. A. M.-S. and S. F.-N. thank Generalitat Valenciana for the FPI Fellowship Program (grant numbers ACIF/2021/294, CIACIF/2021/050 and BEFPI/2024/29). D. B. and M. Z. would like to acknowledge financial support from the Helmholtz Association. Authors also want to acknowledge I. S.-S. and M. P. for their technical assistance and advice.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrochemical Response of Cold-Sintered Cathode-Hybrid Electrolyte Bilayers: Deep Insights into the Determining Kinetic Mechanisms via Operando Electrochemical Impedance Characterization

  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Barba-Juan, Antonio
  • Garcia-Belmonte, Germà
  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
[EN] This study reports the fabrication of solid-state bilayers combining LiFePO4 (LFP) cathodes with Li1.3Al0.3Ti1.7(PO4)3 (LATP)-based composite solid electrolytes using a cold sintering process. By optimizing sintering pressure, intimate cathode–electrolyte contact is achieved, resulting in improved electrochemical performance. Bilayers cold-sintered at 300 MPa and 150 degrees C show high ionic conductivity (about 0.5 mS cm-1) and stable room-temperature capacities (160.1 mAh g-1 of LFP at C/10 and 75.8 mAh g-1 of LFP at 1 C). Operando electrochemical impedance spectroscopy is used to identify kinetic limitations and predict overall behavior. The results indicate that capacity fading may occur at higher pressures due to volume contraction of the LFP crystal cell. Overall, the work highlights cold sintering as a simple route to high-performance solid-state bilayers and demonstrates operando EIS as a non-destructive tool to understand and mitigate degradation in solid-state lithium batteries., A.B.-J. and G.G.-B. acknowledge the financial support from Generalitat Valenciana under Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030), and A.B.-J. also acknowledges Ministerio de Ciencia, Innovacion y Universidades (Spain) (grant number MCIN/AEI/10.13039/501100011033). N.V.-A. thanks the financial support from UJI (UJI-2023-16 and GACUJIMC/2023/08). A.M.-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program (grant numbers ACIF/2020/294 and CIACIF/2021/050). The authors also acknowledge SCIC from UJI and Celgard for supplying the separator membranes.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Using in operando impedance spectroscopy technique to unravel the sintering process evolution of Bi2O3:LATP cold-sintered solid electrolyte

  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
  • Ferrer-Nicomedes, Sergio
  • Simon, Sonia
  • Vicente-Agut, Nuria
  • Jarque Fonfría, Juan Carlos
  • Barba Juan, Antonio
[EN]A NASICON-type Li₁₊ₓAlₓTi₂₋ₓ(PO₄)₃ (LATP) cold-sintered solid electrolyte with a dense structure is reported as a potential alternative to conventional liquid organic electrolytes. A low-temperature sintering approach (below 200 °C) was developed, employing a sintering additive, an acid-based solvent, and high pressure to fabricate the solid electrolyte. Additionally, an in operando impedance technique was integrated into the setup, enabling real-time monitoring of the Cold Sintering Process (CSP) to investigate the mechanisms occurring during densification. As a result, an ionic conductivity as high as 4.48 × 10⁻⁵ S·cm⁻¹, with a relative density of approximately 82%, was achieved using a mixture of LATP powder with 2 wt% Bi₂O₃ and 25 wt% 3 M acetic acid solution, sintered under 700 MPa at 150 °C. This represents one of the highest reported values in peer-reviewed literature for cold-sintered LATP ceramics. However, the CSP-fabricated samples, without subsequent high-temperature annealing treatments, exhibit kinetic limitations attributed to intergranular regions. Overcoming this bottleneck is essential to further enhance ionic conductivity at low processing temperatures., All authors are grateful to the Generalitat Valenciana for funding their research projects within the framework of Pla Complementari Programa de Materials Avançats , 2022 (MFA/2022/030). A.B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion ¿ (Spain) under project no. MCIN/AEI/10.13039/501100011033. A.M.-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program (ACIF/2020/294 and ACIF/2021/050). N.V.-A. acknowledges funding by Universitat Jaume I under the grant number POSDOC/2020/04.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

The role of the LATP particle size as a cornerstone of the cold sintering process

  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Barba Juan, Antonio
[EN] An innovative sintering technique, the Cold Sintering Process (CSP), has been employed to obtain dense Li1.3Al0.3Ti1.7(PO4)3 (LATP) Solid-State Electrolytes (SSE) by optimising the particle size (d50) of the starting powder. The CSP is carried out at 700 MPa, 150 ºC, and 90 min of sintering time, using acetic acid solution as Transient Liquid Phase (TLP). The CSP lowers the LATP sintering temperatures almost 1000 ºC. To study the electrical properties, an in operando Electrochemical Impedance Spectroscopy (EIS) technique has been used. The optimum d50 is 0.415 ¿m, yielding to competitive microstructure and electrical properties (ionic conductivity of 6.93¿10 5 S cm-1 at 30 ºC, activation energy of 0.363 eV, and a relative density of 81.2 ± 0.8%). Relative density, ionic conductivity and TLP content must be balanced, because at small d50, although relative density is enhanced the ionic conductivity is reduced. A packing model has been used to understand this behaviour and the mass transfer mechanisms, This work has received funding from Generalitat Valenciana under Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030) . A.B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion (Spain) grant number. MCIN/AEI/10.13039/501100011033. N.V.-A. acknowledges the support for the research from Universitat Jaume I under the grant number POSDOC/2020/04. A.M.-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program (grant numbers ACIF/2021/294 and ACIF/2021/050) . The authors also acknowledge SCIC from UJI.r 2020/04. A.M.-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program (grant numbers ACIF/2021/294 and ACIF/2021/050) . The authors also acknowledge SCIC from UJI.