Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 7
Encontrada(s) 1 página(s)

RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Microwave-Driven Densification of NASICON-type LATP: A Fast Route Toward Efficient Solid-State Electrolytes

  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
  • Salvador Moya, Mª Dolores|||0000-0002-4242-478X
  • Borrell Tomás, María Amparo|||0000-0003-4292-4538
  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
[EN] The transition from flammable liquid electrolytes to safer solid-state electrolytes is essential for next-generation batteries. Li1.3Al0.3Ti1.7(PO4)3 (LATP) is a promising NASICON-type electrolyte, but its application is hindered by energy-intensive high-temperature sintering. This work demonstrates microwave sintering as a rapid and efficient route to fabricate dense, highly conductive LATP. Green bodies with a relative density of 71% were obtained by combined uniaxial and isostatic pressing, followed by microwave sintering between 800 and 1100 ºC for only 10 minutes. Optimal densification (91.4%) was achieved at 1000 ºC, while higher temperatures led to abnormal grain growth and rutile-TiO2 formation. Electrochemical impedance spectroscopy revealed a strong reduction in grain-boundary resistance above 950 ºC. LATP sintered at 1000 ºC exhibited an ionic conductivity of 5·10-4 S cm-1 and an activation energy of 0.20 eV. Symmetric Li|LATP|Li cells showed stable cycling over 500 h with low overpotentials, confirming excellent transport and mechanical integrity., This publication is part of the grants PID2021-128548OB-C21 & C22 and CNS2023-144190 funded by MICIU/AEI/10.13039/501100011033, "ERDF/EU" and the "European Union NextGenerationEU/PRTR". A.M.-S. acknowledges the funding from the Aid for Early Research Projects (PAID-06-25) and the postdoctoral fellowship (PAID-10-24) programs from the Vice-Rectorate for Research of Universitat Politecnica de Valencia. S.F.-N thanks Generalitat Valenciana through FPI Fellowship Program (CIACIF/2021/050) . N. V.-A. acknowledges support for the research from Universitat Jaume I under the project number UJI/2023/016. Authors thank Felipe L. Penaranda-Foix from ITACA facilities for performing the dielectric measurements.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo de revisión (ReviewArticle)

Sintering science meets sustainability: a review of cold sintering process in solid-state electrolytes

  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Barba Juan, Antonio
[EN] The global push for deep decarbonization by 2050 has accelerated energy storage development to address power intermittency. This review covers ceramic- and polymer-in-ceramic solid-state electrolytes obtained via the cold sintering process, which enables higher energy density and safety by replacing liquid electrolytes and supporting lithium-metal anodes. Cold sintering, at temperatures below 300 ¿C, provides fast densification with low environmental impact compared to traditional high-temperature sintering. It affects microstructure, phase stability, and ionic transport. Important applications include lithium and sodium solid electrolytes with notable density and conductivity. Challenges remain in material optimization, scaling, and integrating multifunctional designs for sustainable, high-performance batteries., A.B.-J. acknowledge the financial support from Generalitat Valenciana under Pla Complementari Programa de Materials Avanc¿ats , 2022 [grant number MFA/2022/030], and A.B.-J. also acknowledges Ministerio de Ciencia e Innovacion; (Spain) [grant number MCIN/AEI/10.13039/501100011033]. Am-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program [grant numbers ACIF/2021/294 and CIACIF/2021/050]. N.V.-A. thanks the financial support from UJI [grant UJI-2023-16].
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Fine-tuning the microstructure for improved performance in cold-sintered Li1. 3Al0. 3Ti1. 7 (PO4) 3 composite solid electrolytes

  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Barba-Juan, Antonio
  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
[EN] Solid-state electrolytes (SSE) are one of the fundamental components of the upcoming generation of batteries since they increase the operational safety and efficiency. In this work, composite solid electrolytes (CSE) based on Li1.3Al0.3Ti1.7(PO4)3 and a (PEO2-LiTFSI) polymer matrix are obtained via the pioneering Cold Sintering Process (CSP), with a drastic reduction of the conventional sintering temperature. The CSP is performed at only 150 °C and 700 MPa, for 90 min of sintering time, by using a 3m acetic acid solution as the transient liquid phase (TLP). Here, the effect of the LATP particle size (d50) is studied to tailor the final microstructure, which enables the fine-tuning of the ultimate electrical properties of the electrolyte. An optimum d50 of 0.415 ¿m produces CSEs with 91 % of relative density, an ionic conductivity of 0.169 mS/cm, activation energy of 0.293 eV and electrical stability under 0.1 mA/cm2, thus leading to competitive properties., A.B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion (Spain) (grant number MCIN/AEI/10.13039/501100011033) and Generalitat Valenciana under Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030) . A.M.-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program (grant numbers ACIF/2020/294 and ACIF/2021/050) . N.V.-A. thanks the financial support from UJI (grant UJI-2023-16) . The authors also acknowledge SCIC from UJI and Celgard for supplying the separator membranes.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Densification and performance optimization of NaSICON solid electrolytes via a low-temperature cold sintering process with sodium ionic salt doping

  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Barba-Juan, Antonio
  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
[EN] Sodium-ion batteries (SIBs) have emerged as a sustainable alternative to lithium-ion systems, offering cost-effective and environmentally friendly energy storage solutions. Solid-state electrolytes (SSEs), particularly NaSICON-type materials such as Na3.4Zr1.9Zn0.1Si2.2P0.8O12 (NZZSP) studied here, are critical for enhancing the safety and stability of SIBs. However, conventional high-temperature sintering methods for fabricating these electrolytes are energy-intensive and environmentally impactful. In this work, we employed the Cold Sintering Process (CSP) to densify NZZSP at a low temperature of 150 °C under 720 MPa with the aid of a transient liquid phase (TLP), achieving a sustainable electrolyte production with competitive performance. The effects of milling time and two different TLP media were evaluated, with 3 M acetic acid solution (HAc) being more effective than 25 mM sodium hydroxide solution (NaOH) in preserving particle integrity and yielding higher ionic conductivity (0.50 mS cm¿1). Doping with NaPF6 and NaTFSI further enhanced performance, with 20% NaPF6-doped samples achieving the highest densification (94.3%) and conductivity (0.80 mS cm¿1). Optimized 2 hour-milled, 20% NaPF6 electrolytes demonstrated suitable cycling stability in symmetric cells (over 500 hours) and specific capacity in half cells, with Na metal and Na3V2(PO4)3 (NVP) as electrodes, of about 85 mA h gNVP ¿1 at C/2 and over 100 mA h gNVP ¿1 at C/10 after cycling at multiple rates. These results underscore the potential of the CSP as a sustainable, low-temperature alternative for fabricating high-performance solid-state electrolytes for application in all solid-state sodium batteries., This work has received funding from Generalitat Valenciana under Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030). A. B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion (Spain) grant number. MCIN/AEI/10.13039/501100011033. N. V.-A. acknowledges the support for the research from Universitat Jaume I under the project number UJI/2023/016. A. M.-S. and S. F.-N. thank Generalitat Valenciana for the FPI Fellowship Program (grant numbers ACIF/2021/294 and CIACIF/2021/050).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Heating-time independent Densification of LATP via Cold Sintering Process

  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
  • Hérisson de Beauvoir, Thomas
  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Estournès, Claude
  • Barba Juan, Antonio
[EN] The Cold Sintering Process has been used to sinter Li1.3Al0.3Ti1.7(PO4)3 powder (LATP) initially mixed with 15 wt.% of a solution of acetic acid 3 m as Transient Liquid Phase (TLP). The effect of variables such as green density, heating rate, sintering temperature, dwell time and the operating pressure on the densification of LATP via CSP has been thoroughly analysed. The operating pressure shows no effect on the green density above 450 MPa. The heating rates, thus the heating time, do not modify the densification behavior of LATP Solid-State Electrolytes (SSEs) but a decomposition reaction takes place at temperatures above 180 ºC. This reaction depends on the TLP amount still present in the pores, and at higher pressures (P>450 MPa) this decomposition effect on densification is reduced as the pore volume becomes smaller. For the first time in the CSP, a linear dependence of relative density on temperature is demonstrated., This work has received funding from Generalitat Valenciana under Pla Complementari Programa de Materials Avançats , 2022 (grant number MFA/2022/030). A.B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion (Spain) grant number. MCIN/ AEI/10.13039/501100011033. N.V.-A. acknowledges the support for the research from Universitat Jaume I under the project number UJI/ 2023/016. A.M.-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program (grant numbers ACIF/2021/294 and CIACIF/2021/ 050). A.M.-S. thanks Generalitat Valenciana through its Internship Fellowship Program for PhD students (grant number CIBEPF/2023/137).
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Pressure-Driven Structural Distortion in Cold Sintered LiFePO4|Li1.3Al0.3Ti1.7(PO4)3 Composite Solid Electrolyte Bilayers

  • Ferrer-Nicomedes, Sergio
  • Zarrabeitia, Maider
  • Bresser, Dominic
  • García-Belmonte, Germà
  • Vicente-Agut, Nuria
  • Barba, Antonio
  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
[EN] The pressure applied during the fabrication of LiFePO4-composite solid electrolyte bilayers via Cold Sintering Process (CSP) is known to influence their electrochemical performance and structural integrity. In a previous work, the authors have reported that bilayers sintered at high pressure (720 MPa) achieve high densification, but exhibit rapid capacity fading and poorer cycling stability compared to those processed at lower pressures (300 MPa). This study employs the galvanostatic intermittent titration technique (GITT), operando X-ray diffraction (XRD), and ex situ X-ray photoelectron spectroscopy (XPS) to elucidate the underlying mechanisms hindering the performance in high-pressure bilayers. GITT reveals larger and progressively increasing overpotentials and internal resistances, as well as irregular ion diffusion in high-pressure bilayers, suggesting altered lithiation kinetics. Operando XRD identifies irreversible phase transformations alongside accumulation of inactive FePO4 species, with XPS confirming the presence of oxidized iron (Fe3+) in the discharged cathodes sintered at high pressure. Notably, lattice distortions in the b and c axes-key lithium diffusion pathways in the olivine structure-are more pronounced at 720 MPa, indicating pressure-induced crystalline deformation modifies the energy barrier for lithium ion migration. Conversely, bilayers sintered at 300 MPa maintain stable structural and kinetic behavior, enabling reversible cycling and superior performance. These findings underscore the delicate balance required in CSP pressure to optimize densification of multi-component structures without compromising electrode functionality, guiding the design of robust solid-state bilayers and multilayers for next-generation battery technologies., This work has received funding from Generalitat Valenciana under Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030). A. B.-J. acknowledges the financial support from Ministerio de Ciencia e Innovacion (Spain) grant number. MCIN/AEI/10.13039/501100011033. N. V.-A. acknowledges the support for the research from Universitat Jaume I under the project number UJI/2023/016. A. M.-S. and S. F.-N. thank Generalitat Valenciana for the FPI Fellowship Program (grant numbers ACIF/2021/294, CIACIF/2021/050 and BEFPI/2024/29). D. B. and M. Z. would like to acknowledge financial support from the Helmholtz Association. Authors also want to acknowledge I. S.-S. and M. P. for their technical assistance and advice.
RiuNet. Repositorio Institucional de la Universitat Politécnica de Valéncia
Publication Artículo científico (JournalArticle)

Electrochemical Response of Cold-Sintered Cathode-Hybrid Electrolyte Bilayers: Deep Insights into the Determining Kinetic Mechanisms via Operando Electrochemical Impedance Characterization

  • Ferrer-Nicomedes, Sergio
  • Vicente-Agut, Nuria
  • Barba-Juan, Antonio
  • Garcia-Belmonte, Germà
  • Mormeneo-Segarra, Andrés|||0000-0002-8827-3649
[EN] This study reports the fabrication of solid-state bilayers combining LiFePO4 (LFP) cathodes with Li1.3Al0.3Ti1.7(PO4)3 (LATP)-based composite solid electrolytes using a cold sintering process. By optimizing sintering pressure, intimate cathode–electrolyte contact is achieved, resulting in improved electrochemical performance. Bilayers cold-sintered at 300 MPa and 150 degrees C show high ionic conductivity (about 0.5 mS cm-1) and stable room-temperature capacities (160.1 mAh g-1 of LFP at C/10 and 75.8 mAh g-1 of LFP at 1 C). Operando electrochemical impedance spectroscopy is used to identify kinetic limitations and predict overall behavior. The results indicate that capacity fading may occur at higher pressures due to volume contraction of the LFP crystal cell. Overall, the work highlights cold sintering as a simple route to high-performance solid-state bilayers and demonstrates operando EIS as a non-destructive tool to understand and mitigate degradation in solid-state lithium batteries., A.B.-J. and G.G.-B. acknowledge the financial support from Generalitat Valenciana under Pla Complementari "Programa de Materials Avancats", 2022 (grant number MFA/2022/030), and A.B.-J. also acknowledges Ministerio de Ciencia, Innovacion y Universidades (Spain) (grant number MCIN/AEI/10.13039/501100011033). N.V.-A. thanks the financial support from UJI (UJI-2023-16 and GACUJIMC/2023/08). A.M.-S. and S.F.-N. thank Generalitat Valenciana through FPI Fellowship Program (grant numbers ACIF/2020/294 and CIACIF/2021/050). The authors also acknowledge SCIC from UJI and Celgard for supplying the separator membranes.