Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 19
Encontrada(s) 1 página(s)

Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Benchmarking of useful phase change materials for a building application

  • Navarro Farré, Lidia
  • Solé, Aran
  • Martín, Marc
  • Barreneche Güerisoli, Camila
  • Olivieri, Lorenzo
  • Tenorio, José Antonio
  • Cabeza, Luisa F.
Nowadays, there is an increasing interest in more efficient building materials and new technologies to accomplish the objectives defined by energy policies. The combination of energy efficient building designs and integration of renewable energies makes the use of thermal energy storage (TES) necessary. Within this context, the improvement of building envelopes by the use of phase change materials (PCM) has been widely studied. The PCM selection should fulfil the requirements of the specific application. In this study, a benchmarking of PCM available in the market was performed to undertake a material selection for a specific building application. The incorporation of PCM into a radiant wall technology present several requirements with especial interest on long-term thermal stability. A complete laboratory-scale characterization has been carried out considering the following properties: temperature of phase change, specific heat capacity, thermal conductivity, and stability., Financiado por el proyecto RTC-2015-3583-5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013-2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad. The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-2-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2017 SGR 1537 and 2017 SGR 188). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Camila Barreneche would like to thank ACCIO for her Grant TecnioSpring Plus TECSPR17-1-0071. Aran Solé would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva FJCI-2015-25741.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Developing a PCM-enhanced mortar for thermally active precast walls

  • Olivieri, Lorenzo
  • Tenorio, José Antonio
  • Revuelta Crespo, David
  • Navarro Farré, Lidia
  • Cabeza, Luisa F.
This work presents an experimental research on the thermal properties of novel cementitious mortars incorporating microencapsulated Phase Change Materials intended to be used as the innermost layer in a precast radiant building component actively controlled by an integrated hydronic system. The characterization was developed in two steps: the first one focused on the effects of different fine aggregates and admixtures for a fixed PCM content and the second one on the effect of changing the amount of PCM. Results show that using silica aggregates and antifoaming admixture outperform the other options, producing mortars with statistically significant higher thermal conductivities, diffusivities and effusivities. Besides, increasing the amount of PCM significantly reduces conductivity and diffusivity, but the effusivity is practically invariant. This suggests that the mortar design has to be defined by predominantly focusing on diffusivity, in order to achieve appropriate heat penetration rates and activation times for an efficient system operation., INPHASE project (RTC-2015-3583-5) has been founded by the Ministry of Economy and Competitiveness within the National Programme for Research Aimed at the Challenges of Society, included in the framework of the Spanish National Plan for Scientific and Technical Research and Innovation 2013-2016, and has been co-financed by the European Regional Development Fund (ERDF), with the aim of promoting technological development, innovation and quality research.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Experimental set-up for testing active and passive systems for energy savings in buildings - Lessons learnt

  • Gracia Cuesta, Alvaro de
  • Navarro Farré, Lidia
  • Coma Arpón, Julià
  • Serrano, Susana
  • Romaní Picas, Joaquim
  • Pérez Luque, Gabriel
  • Cabeza, Luisa F.
This paper describes a building prototype experimental set-up used for testing active and passive systems for energy savings, presenting the used methodology, reviewing the main experimental results and identifying limitations. The test facility is located in Puigverd de Lleida (Spain) and has been experimentally evaluating different materials, technologies and systems which might be integrated in building design to provide energy savings for space heating and cooling since 2002. The research fields of passive technologies covered the effect of using different insulating materials, construction systems based on sustainable materials, addition of phase change materials in building envelopes and green infrastructures such as green roofs and walls. On the other hand, the active systems tested were focused in exploiting different available renewable energy source available, such a solar thermal, free-cooling with night air, or geothermal heat, using thermal energy storage systems to shift the heating and cooling loads., The work partially funded by the Spanish Government (ENE2008-06687-C02-01/CON, ENE2011-28269-C03-02, ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-3-R (MINECO/FEDER), and ULLE10-4E-1305). Financiado por el proyectoRTC-2015-3583-5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013–2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. The research leading to these results has received funding from the European Union's Seventh Framework Programe (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE), from MOPCON Project (EU CRAFT ref. G5ST-CT-2002-50331), from Eccoinnovation Project Rewastee ECO/13/630286 and from European Union's Horizon 2020 Research and Innovation Programme under grant agreement No. 657466 (INPATH-TES) and from EEA-Grants under grant IDI-20140914. This work was supported by the “Corporación Tecnológica de Andalucía” by means of the project “MECLIDE-Soluciones estructurales con materiales especiales para la climatización diferida de edificios” with the collaboration of DETEA. Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940. Julià Coma would like to thank the Departament d′Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship. Cecilia Castellón, Pablo Arce, Albert Castell, Cristian Solé, Pere Moreno and Lídia Rincón participated in the experimentation in this set-up.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Empirical equation to estimate viscosity of paraffin

  • Ferrer, Gerard
  • Gschwander, Stefan
  • Solé, Aran
  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
  • Schossig, Peter
  • Cabeza, Luisa F.
Thermal energy storage (TES) systems using phase change materials (PCM) are nowadays widely developed to be applied in solar power plants or cooling and domestic comfort services. The design of a TES system does not only rely on the energy density that a PCM can provide, but also on other important material properties such as its rheological behavior when the PCM is melted. Viscosity varies with temperature, but the lack of an empirical equation predicting its value has lead researchers to simulate the system performance taking constant viscosity values which, consequently, have led to errors on the designs. As paraffin are one of the most common PCM types used, the present paper evaluates the rheology of four commercial paraffin with different phase change temperatures in order to find out an empirical equation for the whole paraffin family. A polynomial 3 model type equation has been found as the best one to predict paraffin viscosity., The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-2-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from RTC-2015-3583-5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013–2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad, and from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Dr. Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-22886.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Behaviour of a concrete wall containing micro‐encapsulated PCM after a decade of its construction

  • Cabeza, Luisa F.
  • Navarro Farré, Lidia
  • Pisello, Anna Laura
  • Olivieri, Lorenzo
  • Bartolomé, Cesar
  • Sánchez Sánchez, José
  • Álvarez Domínguez, Servando
  • Tenorio, José Antonio
Today, our society has the duty of reducing the energy consumed in the building sector. A promising technology to achieve this goal is the implementation of thermal energy storage (TES) solutions in buildings envelope. Lately, much literature dealing with the effect of the inclusion of latent heat storage materials in construction materials to provide higher thermal inertia has appeared, mostly focusing on the evaluation of the thermal properties, density, or porosity of these new materials. However, few of them evaluated the long stability properties of the materials with embedded PCM when included in a building, very much needed since the lifetime of a building is about 50 years. Therefore, in this study, an evaluation of a house‐like cubicle of concrete with micro‐encapsulated PCM after a decade of its construction is carried out. The results are compared to the tests done in 2005 concluding that the thermal performance of this cubicle presented no degradation in the PCM effect., The work partially funded by the Spanish Government (ENE2015‐64117‐C5‐1‐R (MINECO/FEDER), ULLE10‐4E‐1305, and ENE2005‐08256‐C02‐01). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Financiado por el proyecto RTC‐2015‐3583‐5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013‐2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad.
Repositori Obert UdL
Publication Artículo científico (JournalArticle)

Building thermal storage technology: Compensating renewable energy fluctuations

  • Guerrero Delgado, M. Carmen
  • Sánchez Ramos, José
  • Álvarez Domínguez, Servando
  • Tenorio, José Antonio
  • Cabeza, Luisa F.
Emerging technologies and new intelligent management systems will be needed to rise to the energy challenges posed by buildings today. Thermally activated building systems (TABS) are attracting growing interest on the back of their energy savings potential. The TABS studied in this article, a new prefabricated panel designed for installation in residential building façades, was characterised by the high thermal inertia afforded by the phase change materials in its composition. The design and assessment of the potential savings derived from TABS require specific characterisation methodologies to estimate the amount of useful energy available to control the indoor environment. A two-stage approach was adopted for the TABS studied here with ``ideal'' operating control (the building is assumed to be at a constant desired temperature). The first stage involved a simplified method for characterising system behaviour based on performance maps developed from CFD simulations. Such maps can be used to quickly assess changes in system energy performance following on variations in design and operating parameters. In the second, the TABS was integrated into a building with a simplified model to assess monthly energy demand to evaluate the system potential for energy savings in representative types of Spanish single-family housing in different climate zones. The first-stage findings showed that given the system significant inertia, it discharged for several days, even when charging occurred only on the first, ensuring a wide operating range adaptable to renewable resource limitations. The analysis of potential, in turn, revealed that savings of over 40% in heating demand are possible even under the least favourable circumstances., This study was funded by Spanish Ministry of Economy and Competitiveness under the INPHASE (RTC-2015-3583-5) and DACAR (BIA2016-77431-C2-2-R), the European Regional Development Fund (ERDF) and the University of Seville under its Research Plan VI (VPPI-US). Prof. Cabeza would like to thank the Catalan Government for the quality accreditation given to her research group GREiA (2017 SGR 1537). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Benchmarking of useful phase change materials for a building application

  • Navarro, Lidia
  • Solé, Aran
  • Martín, Marc
  • Barreneche, Camila
  • Olivieri, Lorenzo
  • Tenorio Ríos, José Antonio
  • Cabeza, Luisa F.
Nowadays, there is an increasing interest in more efficient building materials and new technologies to accomplish the objectives defined by energy policies. The combination of energy efficient building designs and integration of renewable energies makes the use of thermal energy storage (TES) necessary. Within this context, the improvement of building envelopes by the use of phase change materials (PCM) has been widely studied. The PCM selection should fulfil the requirements of the specific application. In this study, a benchmarking of PCM available in the market was performed to undertake a material selection for a specific building application. The incorporation of PCM into a radiant wall technology present several requirements with especial interest on long-term thermal stability. A complete laboratory-scale characterization has been carried out considering the following properties: temperature of phase change, specific heat capacity, thermal conductivity, and stability., Financiado por el proyecto RTC-2015-3583-5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013–2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad. The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-2-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2017 SGR 1537 and 2017 SGR 188). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Camila Barreneche would like to thank ACCIO for her Grant TecnioSpring Plus TECSPR17-1-0071. Aran Solé would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva FJCI-2015-25741., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Laboratory test cells for evaluate the real performance of precast concrete façade with PCM

  • Tenorio Ríos, José Antonio
  • Marcos, Ana
  • Guerrero Delgado, M. Carmen
  • Sánchez-Ramos, José
  • Álvarez, Servando
  • Cabeza, Luisa F.
Trabajo presentado al Eurotherm Seminar #112: Advances in Thermal Energy Storage, celebrado en la Universitat de Lleida del 15 al 17 de mayo de 2019., The Inphase project proposes the development of a precast concrete façade with incorporated Phase Changing Materials (PCMs) for residential buildings¿ envelopes, taking advantage of the latent thermal storage capacity of the latter in order to improve the overall performance of the building. The solution is based in layers of mortars and slurries for incorporation in precast building components actively controlled by means of an integrated hydronic radiant system. In order to evaluate the performance of different solutions, an experimental infrastructure was developed with laboratory test cells with increasing amounts of microencapsulated PCM (0%, 9%, 19%, 24% and 32%) proportions in relation to the total volume of PCM containing concrete. The temperature of the system is modified and controlled through an active water installation and measured at different points of the testing blocks and pipes, providing an in-depth analysis of the dynamic response of the system. The idea is to be able to activate or control the thermal inertia of the material at will for the development of the experiment as well as future applications. The models were devised to be monitored in order to obtain a detailed study of their thermal properties and performance, such as temperature profiles, heat flux, dampening or phase shift. This information will later be used to validate the simulation model, which enables the digital analysis of a building with these materials incorporated as part of its envelope, INPHASE project (RTC-2015-3583-5) has been founded by the Ministry of Economy and Competitiveness within the National Programme for Research Aimed at the Challenges of Society, included in the framework of the Spanish National Plan for Scientific and Technical Research and Innovation 2013-2016, and has been co-financed by the European Regional Development Fund (ERDF), with the aim of promoting technological development, innovation and quality research.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Developing a PCM-enhanced mortar for thermally active precast walls

  • Olivieri, Lorenzo
  • Tenorio Ríos, José Antonio
  • Revuelta Crespo, David
  • Navarro, Lidia
  • Cabeza, Luisa F.
This work presents an experimental research on the thermal properties of novel cementitious mortars incorporating microencapsulated Phase Change Materials intended to be used as the innermost layer in a precast radiant building component actively controlled by an integrated hydronic system. The characterization was developed in two steps: the first one focused on the effects of different fine aggregates and admixtures for a fixed PCM content and the second one on the effect of changing the amount of PCM. Results show that using silica aggregates and antifoaming admixture outperform the other options, producing mortars with statistically significant higher thermal conductivities, diffusivities and effusivities. Besides, increasing the amount of PCM significantly reduces conductivity and diffusivity, but the effusivity is practically invariant. This suggests that the mortar design has to be defined by predominantly focusing on diffusivity, in order to achieve appropriate heat penetration rates and activation times for an efficient system operation., INPHASE project (RTC-2015-3583-5) has been founded by the Ministry of Economy and Competitiveness within the National Programme for Research Aimed at the Challenges of Society, included in the framework of the Spanish National Plan for Scientific and Technical Research and Innovation 2013-2016, and has been co-financed by the European Regional Development Fund (ERDF), with the aim of promoting technological development, innovation and quality research., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Development of cementitious mortars incorporating PCMs for radiant heating and cooling systems

  • Olivieri, Lorenzo
  • Tenorio Ríos, José Antonio
  • Revuelta Crespo, David
  • Navarro, Lidia
  • Cabeza, Luisa F.
Trabajo presentado a la International Conference on Construction Research / Eduardo Torroja: Architecture, Engineering, Concrete (AEC), celebrada en el Instituto de Ciencias de la Construcción Eduardo Torroja (IETCC-CSIC) del 21 al 23 de noviembre de 2018., [ES]: Las estrategias centradas en lograr el confort térmico en edificios, al tiempo que se reduce la demanda energética en calefacción, ventilación y refrigeración (HVAC por sus siglas en inglés), como los Sistemas de Almacenamiento de Energía Térmica (TES por sus siglas en inglés) o los de Estructuras Termoactivas (TABS por sus siglas en inglés), han ganado interés demostrando un gran potencial. La activación térmica de los componentes de un edificio ha demostrado ser una opción viable para la reducción de la demanda energética de los edificios debido principalmente a su funcionamiento a baja temperatura y la alta inercia térmica que permite recortar los picos de temperatura máxima y desplazar el consumo de energía a períodos de bajo costo. Este trabajo presenta los resultados obtenidos en el desarrollo de materiales cementicos con incorporación de Materiales de Cambio de Fase (PCM por sus siglas en inglés) que, en combinación con los TABS, pueden resultar en una mejora del confort térmico de los edificios y al mismo tiempo en una reducción del consumo de energía en HVAC., [EN]: Strategies focused on achieving thermal comfort in buildings, while reducing heating, ventilation and air conditioning (HVAC) energy demand, such as Thermal Energy Storage (TES) systems and Thermally Activated Building Systems (TABS), have gained interest proving high energy savings potential. The thermal mass activation of building components has proved to be a viable option for energy use reduction in buildings mainly due to its low temperature operation and the high thermal inertia that enables shaving peak loads and shifting energy consumption to low energy cost periods. This works presents the results obtained in the development of cementitious mortars incorporating Phase Change Materials (PCM) that, in combination with TABS might result in an improvement of the thermal comfort in buildings and at the same time in a reduction of the HVAC energy consumption., Parte de las investigaciones en este trabajo han sido financiadas por el Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, dentro del proyecto “INPHASE (RTC-2015-3583-5).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Micro-encapsulated PCM in concrete matrix after a decade of the building construction

  • Olivieri, Lorenzo
  • Tenorio Ríos, José Antonio
Trabajo presentado a la 14th International Energy Storage Conference (EnerSTOCK), celebrada en la Universidad de Çukurova (Turquía) del 25 al 28 de abril de 2018., The reduction of the energy consumed in the building sector is no more a recommendation, but a duty of our society. Thermal energy storage (TES) implementation into buildings envelope has been highlighted as a promising technology to reduce the energy demand in buildings. Last decade, many literature have been dealing with the effect of the inclusion of latent heat storage materials in construction materials to provide higher thermal inertia. Several studies focused on the evaluation of the thermal properties, density, or porosity of these new materials. However, few of them focused on the long stability properties of the materials with embedded PCM when included in a building, since the lifetime of a building last around 50 years. In this study, an evaluation of a house-like cubicle of concrete with micro-encapsulated PCM after a decade of its construction is done. The results of this study were compared to the tests done in 2005 concluding that the thermal performance of this cubicle presented no degradation in the PCM effect., The work partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER), ENE2015-64117-C5-3-R (MINECO/FEDER), ULLE10-4E-1305, and ENE2005-08256-C02-01). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Financiado por el proyecto RTC-2015-3583-5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013-2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Behaviour of a concrete wall containing micro‐encapsulated PCM after a decade of its construction

  • Cabeza, Luisa F.
  • Navarro, Lidia
  • Pisello, Ana Laura
  • Olivieri, Lorenzo
  • Bartolomé, Cesar
  • Sánchez, José
  • Álvarez, Servando
  • Tenorio Ríos, José Antonio
Today, our society has the duty of reducing the energy consumed in the building sector. A promising technology to achieve this goal is the implementation of thermal energy storage (TES) solutions in buildings envelope. Lately, much literature dealing with the effect of the inclusion of latent heat storage materials in construction materials to provide higher thermal inertia has appeared, mostly focusing on the evaluation of the thermal properties, density, or porosity of these new materials. However, few of them evaluated the long stability properties of the materials with embedded PCM when included in a building, very much needed since the lifetime of a building is about 50 years. Therefore, in this study, an evaluation of a house‐like cubicle of concrete with micro‐encapsulated PCM after a decade of its construction is carried out. The results are compared to the tests done in 2005 concluding that the thermal performance of this cubicle presented no degradation in the PCM effect., The work partially funded by the Spanish Government (ENE2015‐64117‐C5‐1‐R (MINECO/FEDER), ULLE10‐4E‐1305, and ENE2005‐08256‐C02‐01). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Financiado por el proyecto RTC‐2015‐3583‐5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013‐2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Building thermal storage technology: Compensating renewable energy fluctuations

  • Guerrero Delgado, M. Carmen
  • Sánchez-Ramos, José
  • Álvarez, Servando
  • Tenorio Ríos, José Antonio
  • Cabeza, Luisa F.
Emerging technologies and new intelligent management systems will be needed to rise to the energy challenges posed by buildings today. Thermally activated building systems (TABS) are attracting growing interest on the back of their energy savings potential. The TABS studied in this article, a new prefabricated panel designed for installation in residential building façades, was characterised by the high thermal inertia afforded by the phase change materials in its composition. The design and assessment of the potential savings derived from TABS require specific characterisation methodologies to estimate the amount of useful energy available to control the indoor environment. A two-stage approach was adopted for the TABS studied here with ``ideal'' operating control (the building is assumed to be at a constant desired temperature). The first stage involved a simplified method for characterising system behaviour based on performance maps developed from CFD simulations. Such maps can be used to quickly assess changes in system energy performance following on variations in design and operating parameters. In the second, the TABS was integrated into a building with a simplified model to assess monthly energy demand to evaluate the system potential for energy savings in representative types of Spanish single-family housing in different climate zones. The first-stage findings showed that given the system significant inertia, it discharged for several days, even when charging occurred only on the first, ensuring a wide operating range adaptable to renewable resource limitations. The analysis of potential, in turn, revealed that savings of over 40% in heating demand are possible even under the least favourable circumstances., This study was funded by Spanish Ministry of Economy and Competitiveness under the INPHASE (RTC-2015-3583-5) and DACAR (BIA2016-77431-C2-2-R), the European Regional Development Fund (ERDF) and the University of Seville under its Research Plan VI (VPPI-US). Prof. Cabeza would like to thank the Catalan Government for the quality accreditation given to her research group GREiA (2017 SGR 1537). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme., Peer reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Building thermal storage technology: Compensating renewable energy fluctuations

  • Guerrero Delgado, M. Carmen
  • Sánchez Ramos, José
  • Álvarez Domínguez, Servando
  • Tenorio, José Antonio
  • Cabeza, Luisa F.
Emerging technologies and new intelligent management systems will be needed to rise to the energy challenges posed by buildings today. Thermally activated building systems (TABS) are attracting growing interest on the back of their energy savings potential. The TABS studied in this article, a new prefabricated panel designed for installation in residential building façades, was characterised by the high thermal inertia afforded by the phase change materials in its composition. The design and assessment of the potential savings derived from TABS require specific characterisation methodologies to estimate the amount of useful energy available to control the indoor environment. A two-stage approach was adopted for the TABS studied here with ``ideal'' operating control (the building is assumed to be at a constant desired temperature). The first stage involved a simplified method for characterising system behaviour based on performance maps developed from CFD simulations. Such maps can be used to quickly assess changes in system energy performance following on variations in design and operating parameters. In the second, the TABS was integrated into a building with a simplified model to assess monthly energy demand to evaluate the system potential for energy savings in representative types of Spanish single-family housing in different climate zones. The first-stage findings showed that given the system significant inertia, it discharged for several days, even when charging occurred only on the first, ensuring a wide operating range adaptable to renewable resource limitations. The analysis of potential, in turn, revealed that savings of over 40% in heating demand are possible even under the least favourable circumstances., This study was funded by Spanish Ministry of Economy and Competitiveness under the INPHASE (RTC-2015-3583-5) and DACAR (BIA2016-77431-C2-2-R), the European Regional Development Fund (ERDF) and the University of Seville under its Research Plan VI (VPPI-US). Prof. Cabeza would like to thank the Catalan Government for the quality accreditation given to her research group GREiA (2017 SGR 1537). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. This work is partially supported by ICREA under the ICREA Academia programme.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Behaviour of a concrete wall containing micro‐encapsulated PCM after a decade of its construction

  • Cabeza, Luisa F.
  • Navarro Farré, Lidia
  • Pisello, Anna Laura
  • Olivieri, Lorenzo
  • Bartolomé, Cesar
  • Sánchez Sánchez, José
  • Álvarez Domínguez, Servando
  • Tenorio, José Antonio
Today, our society has the duty of reducing the energy consumed in the building sector. A promising technology to achieve this goal is the implementation of thermal energy storage (TES) solutions in buildings envelope. Lately, much literature dealing with the effect of the inclusion of latent heat storage materials in construction materials to provide higher thermal inertia has appeared, mostly focusing on the evaluation of the thermal properties, density, or porosity of these new materials. However, few of them evaluated the long stability properties of the materials with embedded PCM when included in a building, very much needed since the lifetime of a building is about 50 years. Therefore, in this study, an evaluation of a house‐like cubicle of concrete with micro‐encapsulated PCM after a decade of its construction is carried out. The results are compared to the tests done in 2005 concluding that the thermal performance of this cubicle presented no degradation in the PCM effect., The work partially funded by the Spanish Government (ENE2015‐64117‐C5‐1‐R (MINECO/FEDER), ULLE10‐4E‐1305, and ENE2005‐08256‐C02‐01). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Financiado por el proyecto RTC‐2015‐3583‐5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013‐2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Experimental set-up for testing active and passive systems for energy savings in buildings - Lessons learnt

  • Gracia Cuesta, Alvaro de
  • Navarro Farré, Lidia
  • Coma Arpón, Julià
  • Serrano, Susana
  • Romaní Picas, Joaquim
  • Pérez Luque, Gabriel
  • Cabeza, Luisa F.
This paper describes a building prototype experimental set-up used for testing active and passive systems for energy savings, presenting the used methodology, reviewing the main experimental results and identifying limitations. The test facility is located in Puigverd de Lleida (Spain) and has been experimentally evaluating different materials, technologies and systems which might be integrated in building design to provide energy savings for space heating and cooling since 2002. The research fields of passive technologies covered the effect of using different insulating materials, construction systems based on sustainable materials, addition of phase change materials in building envelopes and green infrastructures such as green roofs and walls. On the other hand, the active systems tested were focused in exploiting different available renewable energy source available, such a solar thermal, free-cooling with night air, or geothermal heat, using thermal energy storage systems to shift the heating and cooling loads., The work partially funded by the Spanish Government (ENE2008-06687-C02-01/CON, ENE2011-28269-C03-02, ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-3-R (MINECO/FEDER), and ULLE10-4E-1305). Financiado por el proyectoRTC-2015-3583-5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013–2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad GREA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2014 SGR 123) and the city hall of Puigverd de Lleida. The research leading to these results has received funding from the European Union's Seventh Framework Programe (FP7/2007-2013) under grant agreement no. PIRSES-GA-2013-610692 (INNOSTORAGE), from MOPCON Project (EU CRAFT ref. G5ST-CT-2002-50331), from Eccoinnovation Project Rewastee ECO/13/630286 and from European Union's Horizon 2020 Research and Innovation Programme under grant agreement No. 657466 (INPATH-TES) and from EEA-Grants under grant IDI-20140914. This work was supported by the “Corporación Tecnológica de Andalucía” by means of the project “MECLIDE-Soluciones estructurales con materiales especiales para la climatización diferida de edificios” with the collaboration of DETEA. Alvaro de Gracia would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-19940. Julià Coma would like to thank the Departament d′Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya for his research fellowship. Cecilia Castellón, Pablo Arce, Albert Castell, Cristian Solé, Pere Moreno and Lídia Rincón participated in the experimentation in this set-up.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Empirical equation to estimate viscosity of paraffin

  • Ferrer, Gerard
  • Gschwander, Stefan
  • Solé, Aran
  • Barreneche Güerisoli, Camila
  • Fernández Renna, Ana Inés
  • Schossig, Peter
  • Cabeza, Luisa F.
Thermal energy storage (TES) systems using phase change materials (PCM) are nowadays widely developed to be applied in solar power plants or cooling and domestic comfort services. The design of a TES system does not only rely on the energy density that a PCM can provide, but also on other important material properties such as its rheological behavior when the PCM is melted. Viscosity varies with temperature, but the lack of an empirical equation predicting its value has lead researchers to simulate the system performance taking constant viscosity values which, consequently, have led to errors on the designs. As paraffin are one of the most common PCM types used, the present paper evaluates the rheology of four commercial paraffin with different phase change temperatures in order to find out an empirical equation for the whole paraffin family. A polynomial 3 model type equation has been found as the best one to predict paraffin viscosity., The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-2-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research groups GREA (2014 SGR 123) and research group DIOPMA (2014 SGR 1543). The research leading to these results has received funding from RTC-2015-3583-5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013–2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad, and from the European Union’s Seventh Framework Programme (FP7/2007-2013) under grant agreement n° PIRSES-GA-2013-610692 (INNOSTORAGE) and from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 657466 (INPATH-TES). Dr. Camila Barreneche would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva, FJCI-2014-22886.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Developing a PCM-enhanced mortar for thermally active precast walls

  • Olivieri, Lorenzo
  • Tenorio, José Antonio
  • Revuelta Crespo, David
  • Navarro Farré, Lidia
  • Cabeza, Luisa F.
This work presents an experimental research on the thermal properties of novel cementitious mortars incorporating microencapsulated Phase Change Materials intended to be used as the innermost layer in a precast radiant building component actively controlled by an integrated hydronic system. The characterization was developed in two steps: the first one focused on the effects of different fine aggregates and admixtures for a fixed PCM content and the second one on the effect of changing the amount of PCM. Results show that using silica aggregates and antifoaming admixture outperform the other options, producing mortars with statistically significant higher thermal conductivities, diffusivities and effusivities. Besides, increasing the amount of PCM significantly reduces conductivity and diffusivity, but the effusivity is practically invariant. This suggests that the mortar design has to be defined by predominantly focusing on diffusivity, in order to achieve appropriate heat penetration rates and activation times for an efficient system operation., INPHASE project (RTC-2015-3583-5) has been founded by the Ministry of Economy and Competitiveness within the National Programme for Research Aimed at the Challenges of Society, included in the framework of the Spanish National Plan for Scientific and Technical Research and Innovation 2013-2016, and has been co-financed by the European Regional Development Fund (ERDF), with the aim of promoting technological development, innovation and quality research.
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Benchmarking of useful phase change materials for a building application

  • Navarro Farré, Lidia
  • Solé, Aran
  • Martín, Marc
  • Barreneche Güerisoli, Camila
  • Olivieri, Lorenzo
  • Tenorio, José Antonio
  • Cabeza, Luisa F.
Nowadays, there is an increasing interest in more efficient building materials and new technologies to accomplish the objectives defined by energy policies. The combination of energy efficient building designs and integration of renewable energies makes the use of thermal energy storage (TES) necessary. Within this context, the improvement of building envelopes by the use of phase change materials (PCM) has been widely studied. The PCM selection should fulfil the requirements of the specific application. In this study, a benchmarking of PCM available in the market was performed to undertake a material selection for a specific building application. The incorporation of PCM into a radiant wall technology present several requirements with especial interest on long-term thermal stability. A complete laboratory-scale characterization has been carried out considering the following properties: temperature of phase change, specific heat capacity, thermal conductivity, and stability., Financiado por el proyecto RTC-2015-3583-5 (INPHASE) del Ministerio de Economía y Competitividad, dentro del Programa Estatal de Investigación, Desarrollo e Innovación Orientada a los Retos de la Sociedad, en el marco del Plan Estatal de Investigación Científica y Técnica y de Innovación 2013-2016, y ha sido cofinanciado con FONDOS FEDER, con el objetivo de promover el desarrollo tecnológico, la innovación y una investigación de calidad. The work is partially funded by the Spanish government (ENE2015-64117-C5-1-R (MINECO/FEDER) and ENE2015-64117-C5-2-R (MINECO/FEDER)). The authors would like to thank the Catalan Government for the quality accreditation given to their research group (2017 SGR 1537 and 2017 SGR 188). GREiA is certified agent TECNIO in the category of technology developers from the Government of Catalonia. Camila Barreneche would like to thank ACCIO for her Grant TecnioSpring Plus TECSPR17-1-0071. Aran Solé would like to thank Ministerio de Economia y Competitividad de España for Grant Juan de la Cierva FJCI-2015-25741.