Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 9
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hybrid binders: A journey from the past to a sustainable future (opus caementicium futurum)

  • Palomo, Ángel
  • Monteiro, P.
  • Martauz, P.
  • Bílek, Vlastimil
  • Fernández-Jiménez, Ana
This article describes and interprets data drawn from a thorough characterisation of a series of cementitious materials. The materials addressed can be divided into three major groups: 1) cements/concretes from well-known and historically documented Roman constructions in Italy; 2) cements recently prepared in the laboratory simulating the compositions of Roman cements, stored for 6 months in environmental conditions similar to those to which the Roman materials have been exposed for 2000 years; 3) concretes prepared from an industrial cement manufactured 6 years ago applying today's knowledge of hybrid cements. An analysis of all the data presented in this article has led its authors to conclude that, conceptually speaking, ancient Roman cements can be identified with modern hybrid ‘portland-alkaline’ materials. That conceptual identity is based on the detection of the same cementitious phases in the two types of cements (Roman and Hybrid) and naturally of the inclusion of alkalis in the structures of some of the phases observed., Data acquired at beamlines 5.3.1 and 8.3.2 at the Advanced Light Source at the Lawrence Berkeley Laboratories, Berkeley, California, were supported by the Director of the Office of Science, Department of Energy, under Contract DEAC02-05CH11231. Angel Palomo and Ana Fernández-Jiménez acknowledge the financing support for the research from Ministerio de Ciencia, Innovación y Universidades and FEDER under research projects BIA2016-76466-R and RTC2016-4872-S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Mechanical-chemical activation of coal fly ashes: An effective way for recycling and make cementitious materials

  • Fernández-Jiménez, Ana
  • García-Lodeiro, Inés
  • Maltseva, O.
This paper is wholly committed to resource efficiency through the valorization of waste from other industries, and more specifically fly ash as a raw material to produce concrete-like geopolymers. In particular, this study aimed to determine the effect of the physical and chemical characteristics of recycled coal fly ash used to manufacture alkaline cement on reaction kinetics and product microstructure and performance. The ash was mixed with 8 M NaOH and cured for 20 h at 85°C and RH > 90% to form a compact paste, after which mechanical strength was determined and the reaction rate was calculated using isothermal conduction calorimetry. The findings showed that vitreous content (SiO2/Al2O3), reactive and (especially) fineness play a very important role in both the development of cement mechanical strength and the composition and structure of the reaction products formed., This research was funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects BIA2013-43293-R, BIA2016-76466-R, and RTC2016-4872-S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Studies about the hydration of hybrid “alkaline-belite” cement

  • Sánchez-Herrero, M. J.
  • Fernández-Jiménez, Ana
  • Palomo, Ángel
The mechanical performance of a hybrid cement containing 48% fly ash, 48% mineralized belite clinker, 1. 5% gypsum and 2.5% Na2SO4 was analyzed and the hydration products were identified. The findings showed that the newly designed cement met European standard EN 197-1 compositional, mechanical and setting time requirements (cement type IVB). The hydration products forming in this blended “alkaline-belite” cement (as it was determined through XRD, 29Si and 27Al MAS NMR and electron microscopy) consisted in a mix of cementitious gels: C-(A)-S-H and N-(C)-A-S-H, which interacted and over time evolved toward the latter with no detriment to the mechanical strength developed by the cement., This research was funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects BIA2016-76466-R and RTC2016-4872-S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Efecto del contenido de C3A en los cementos híbridos

  • Regidor, P.
  • Maltseva, O.
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
Póster presentado a las II Jornadas de Jóvenes Científicos en Materiales de Construcción, celebradas en Madrid del 27 al 28 de mayo de 2019., Los cementos híbridos son unos cementos con muy bajo contenido de cemento portland (< 30%) y elevados contenidos de ceniza volante (<70%). Para acelerar el desarrollo de las resistencias iniciales se incorpora un activador alcalino (< 5%). El objetivo de este trabajo es determinar cómo influye el tipo de cemento empleado en la elaboración de cementos híbridos, más concretamente el contenido de C3A del cemento. Para este estudio se han empleado dos cementos comerciales: A=CEM I 52,5 R y B=CEM I 52,5 SR. Con ellos se elaboraron dos cementos híbridos: HYCA (27.5 % CEM I 52,5 R + 67.5 %5 % ceniza volante +5% activador) y HYCB (27.5 % CEM I 52,5 SR + 67.5 %5 % ceniza volante +5% activador). Inicialmente se determinaron las resistencias mecánicas en pasta, los tiempos de fraguado, y el calor liberado por calorimetría de conducción isoterma. Las pastas fueron caracterizadas por DRX y FTIR a 28 días. Finalmente se elaboraron hormigones a 2 y 28 días. Los resultados obtenidos muestran que, de los dos cementos híbridos, el que tiene un mayor contenido de C3A da lugar a cementos con tiempos de fraguado más cortos, y mayores resistencias iniciales., Ministerio de Ciencia Innovación y Universidades y fondos FEDER que subvencionan los proyectos BIA2016-76466-R y RTC2016-4872-S. Gracias también al MINECO y UE por la subvención del contrato de iniciativa al empleo Juvenil EI-GARJUV-GP17-0045 CAMGP17-IETCC_001.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

New alkaline-belitic hybrid binders

  • Palomo, Ángel
  • Fernández-Jiménez, Ana
  • Sánchez-Herrero, M. J.
Trabajo presentado al 15th International Congress on the Chemistry of Cement (ICCC), celebrado en Praga (República Checa) del 16 al 20 de septiembre de 2019., This paper summarises a long-term study organized in two consecutive steps. The first, which involved exploring a number of laboratory-synthesised belite clinkers with slightly different mineral compositions in depth, culminated in the industrial-scale manufacture of one of those materials. In the second a hybrid alkaline belite cement was prepared containing 48 % of the industrial belite clinker, 48 % fly ash and 4 % chemicals. The hybrid binder was subsequently analysed to determine its mechanical strength and hydration products. The findings showed that the hybrid alkaline belite cement designed met the compositional, mechanical and setting time requirements laid down in European standard EN 197-1 and that its hydration favoured the simultaneous precipitation of a mix of cementitious gels: C-(A)-S-H and N-(C)-A-S-H., This research was funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects BIA2016‐76466‐R and RTC2016‐4872‐S.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Effect of curing temperature in the hydration of a belite cement with high level of fly ash

  • Qu, Bo
  • Sánchez-Herrero, M. J.
  • Martín, Antonia
  • Pastor, José Y.
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
Trabajo presentado al 15th International Congress on the Chemistry of Cement (ICCC), celebrado en Praga (República Checa) del 16 al 20 de septiembre de 2019., This study aimed to determine the physical, mechanical, mineral and microstructural properties of a industrially manufactured hybrid cement (HYP), consisting 47,5 % Belite clinker + 47,5 % FA + 5 % solid alkaline activator. The effect of the curing temperature (25ºC, or 85 ºC) on hydration kinetics and on compressive strength development (in paste prisms and mortar prisms) was determined. Isothermal conduction calorimetry shows that curing at 85ºC, accelerates relevantly the hydration process. The 3 days compressive strength achieved by curing at 25oC was 9 MPa, but 30 MPa was the mechanical strength after 3 days if mortars were cured at 85ºC. After 28 days, the compressive strength of the specimen cured at 25oC was 33 MPa, and 43 MPa after 90 days. The specimens cured at 85oC exhibited a slightly better compressive strength. The hydration products formed were characterized using XRD, SEM/EDX and 27Al and 29Si MAS-NMR. The main reaction product formed was found to be a mixture of cementitious gels: C-(A)-S-H /C-A-S-H/(N,C )-A-S-H. The initial curing at 85°C for 20 h inhibited the formation of ettringite (or favored its rapid decomposition), at least during the first 90 days (maximum age of the materials analyzed in this work). On the contrary, curing at 85ºC favors the precipitation of the sulphates in the form of Phase U., This research was funded by the Spanish Ministry of the Economy, Industry and Competitiveness and FEDER under research projects BIA2016-76466-R and RTC2016-4872-S, Ministry of Economy and Competitiveness of Spain (MAT2015-70780-C4-4-P), and Community of Madrid (S2013/MIT-2862-MULTIMATCHALLENGE). Author QuBo, a Ph.D. the student worked under a China Scholarship Council (CSC) grant.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hybrid alkaline cements: Bentonite-Opc binders

  • García-Lodeiro, Inés
  • Fernández-Jiménez, Ana
  • Palomo, Ángel
This article belongs to the Special Issue Geopolymers., Moderately alkaline activators can be used to formulate cementitious binders with a high Supplemetary Cementitious Materials (SCMs) and a low portland cement content (hybrid alkaline cements). This study aimed to prepare hybrid alkaline cements containing large percentages of dehydroxylated bentonite (BT) and small Portland cement (OPC) fractions, with 5% Na2SO4 as a solid alkaline activator. The hydration kinetics of the pastes hydrated in water in the presence and absence of the solid activator were assessed by isothermal conduction calorimetry, whilst the reaction products were characterised with X-Ray Powder Diffraction (XRD) and Fourier-transform Infrared Spectroscopy (FTIR). The presence of the alkaline activator hastened OPC and BT/OPC hydration: more heat of hydration was released, favouring greater initial bentonite reactivity. The portlandite forming during cement hydration reacted readily with the Na2SO4, raising medium alkalinity and enhancing bentonite dissolution and with it reaction product precipitation (primarily (N,C)-A-S-H-like gels that co-exist with C-S-H- or C-A-S-H-like gels). The presence of sulfate ions favoured the formation of AFm-like phases. Preceding aspects accelerated the hydration reactions, with the formation of more reaction product and matrix densification. As a result, the 28 days Na2SO4 activated systems developed greater mechanical strength than the water-hydrated systems, with the 60% BT/40% OPC blends exhibiting higher compressive strength than the 100% OPC pastes., This research was funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects BIA2016-76466-R and RTC2016-4872-S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hydration mechanisms of hybrid cements as a function of the way of addition of chemicals

  • Fernández-Jiménez, Ana
  • García-Lodeiro, Inés
  • Maltseva, O.
  • Palomo, Ángel
In this study fly ash contents of up to 50% were used to produce binders with mechanical strength greater than or equal to type CEM I 42.5R cement (reference). The specific aim pursued in this research was to determine whether the procedure used to add the chemical activator (in solid or liquid form) can affect strength development in the cement or the nature of the reaction products formed. Two experimental procedures were deployed: (a) the chemical activator was dissolved in the mixing water; (b) the chemical activator was ground, as a solid, into the fly ash. The solid‐state method induced slightly higher mechanical strength than when the activator was dissolved in hydration water. The way the chemical activator was added affected not only early age reaction kinetics, but also the nature and composition of the reaction products, the liquid state favoring the formation of phases AFt and AFm., This research was funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects BIA2016‐76466‐R and RTC2016‐4872‐S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Use of industrial by-products as alkaline cement activators

  • García-Lodeiro, Inés
  • Cristelo, Nuno
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
Alkaline (or geopolymer) cements have proven to be a sustainable alternative to the ordinary portland cement material. The laboratory reagents normally used as alkaline activators constitute the most costly and on occasion polluting constituents of such cementitious systems. This study aimed to explore the use of a disposed cleaning solution (CS), coming from the aluminium transformation industry, as an activator for high and low calcium aluminosilicate precursors. For that a Blast Furnace Slag (BFS) and a type F-Fly Ash (FA) were used. Precursors activated with a traditional NaOH solutions were used as a reference. Kinetics of reactions (isothermal calorimetry) were evaluated and mechanical strength of hardened pastes determined. The nature of the reaction products generated in this new systems were also identified by using XRD, FTIR, SEM and 29Si and 27Al MAS NMR. The findings showed that the CS can be effectively used to prepare cementitious materials, particularly when applied to CaO-SiO2-Al2O3 system precursors such as BFS, which require lower alkalinity than FA-based precursors. The nature of the reaction products generated in the CS alkali activated systems was similar than those observed in the reference systems, however Al richer reaction products were observed in the former., This research was funded by the Spanish Ministry of Science, Innovation and Universities under project BIA2016-76466-R and ERDF under project RTC2016-4872-S (principal investigators Angel Palomo and Ana Fernandez-Jimenez). In addition, thanks the project from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 734833., Peer reviewed