Skip to main content

AVANCES EN CIENCIA Y TECNOLOGIA DE CEMENTOS HIBRIDOS- SOSTENIBLES

BIA2016-76466-R

•
Funding agency name Agencia Estatal de Investigación
Funding agency acronym AEI
Program Programa Estatal de I+D+i Orientado a los Retos de la Sociedad
Call Proyectos I+D+i Retos de Investigación
Call year 2016
State Plan 2013-2016 Plan Estatal de Investigación Científica y Técnica y de Innovación
Beneficiary centre AGENCIA ESTATAL CONSEJO SUPERIOR DE INVESTIGACIONES CIENTIFICAS (CSIC)

Resultados relacionados

Resultados totales (Incluyendo duplicados): 27
Encontrada(s) 1 página(s)

DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of alkali concentration on the activation of carbonate-high illite clay

  • D’Elia, Angela
  • Pinto, Daniela
  • Eramo, Giacomo
  • Laviano, Rocco
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
This article belongs to the Special Issue Low Binder Concrete and Mortars., The present study explores the effect of activating solution concentration (4, 6 and 8 M NaOH) on mechanically and thermally pre-treated carbonate-high illite clay (LCR). Pastes were prepared with an alkaline solution/clay (S/B) ratio of 0.55, which were cured at room temperature and relative humidity > 90% in a climatic chamber. At two and 28 days, compressive mechanical strength was determined, and the reaction products were characterised by X-ray Powder Diffraction analysis (XRPD), Fourier-transform infrared spectroscopy (FTIR) and Scanning Electron Microscopy - Energy Dispersive X-ray spectroscopy (SEM/EDX). Results obtained showed that the presence of reactive calcium in the starting clay induces co-precipitation of a mix of gels: An aluminium-enriched C-S-H gel (C-A-S-H) and a N-A-S-H gel, in which sodium is partially replaced by calcium (N,C)-A-S-H. Pastes prepared with higher (6 or 8 M) activator concentrations exhibit a more compact matrix than the ones prepared with 4 M NaOH. The findings show that the use of a 6 M NaOH solution yields a binder with two days compressive strength >20 MPa and 28 days strength of over 30 MPa., The research was also partially funded by the Spanish Ministry of the Economy, Industry and Competitiveness and ERDF under project BIA2016-76466-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hybrid binders: A journey from the past to a sustainable future (opus caementicium futurum)

  • Palomo, Ángel
  • Monteiro, P.
  • Martauz, P.
  • Bílek, Vlastimil
  • Fernández-Jiménez, Ana
This article describes and interprets data drawn from a thorough characterisation of a series of cementitious materials. The materials addressed can be divided into three major groups: 1) cements/concretes from well-known and historically documented Roman constructions in Italy; 2) cements recently prepared in the laboratory simulating the compositions of Roman cements, stored for 6 months in environmental conditions similar to those to which the Roman materials have been exposed for 2000 years; 3) concretes prepared from an industrial cement manufactured 6 years ago applying today's knowledge of hybrid cements. An analysis of all the data presented in this article has led its authors to conclude that, conceptually speaking, ancient Roman cements can be identified with modern hybrid ‘portland-alkaline’ materials. That conceptual identity is based on the detection of the same cementitious phases in the two types of cements (Roman and Hybrid) and naturally of the inclusion of alkalis in the structures of some of the phases observed., Data acquired at beamlines 5.3.1 and 8.3.2 at the Advanced Light Source at the Lawrence Berkeley Laboratories, Berkeley, California, were supported by the Director of the Office of Science, Department of Energy, under Contract DEAC02-05CH11231. Angel Palomo and Ana Fernández-Jiménez acknowledge the financing support for the research from Ministerio de Ciencia, Innovación y Universidades and FEDER under research projects BIA2016-76466-R and RTC2016-4872-S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Mechanical-chemical activation of coal fly ashes: An effective way for recycling and make cementitious materials

  • Fernández-Jiménez, Ana
  • García-Lodeiro, Inés
  • Maltseva, O.
This paper is wholly committed to resource efficiency through the valorization of waste from other industries, and more specifically fly ash as a raw material to produce concrete-like geopolymers. In particular, this study aimed to determine the effect of the physical and chemical characteristics of recycled coal fly ash used to manufacture alkaline cement on reaction kinetics and product microstructure and performance. The ash was mixed with 8 M NaOH and cured for 20 h at 85°C and RH > 90% to form a compact paste, after which mechanical strength was determined and the reaction rate was calculated using isothermal conduction calorimetry. The findings showed that vitreous content (SiO2/Al2O3), reactive and (especially) fineness play a very important role in both the development of cement mechanical strength and the composition and structure of the reaction products formed., This research was funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects BIA2013-43293-R, BIA2016-76466-R, and RTC2016-4872-S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Studies about the hydration of hybrid “alkaline-belite” cement

  • Sánchez-Herrero, M. J.
  • Fernández-Jiménez, Ana
  • Palomo, Ángel
The mechanical performance of a hybrid cement containing 48% fly ash, 48% mineralized belite clinker, 1. 5% gypsum and 2.5% Na2SO4 was analyzed and the hydration products were identified. The findings showed that the newly designed cement met European standard EN 197-1 compositional, mechanical and setting time requirements (cement type IVB). The hydration products forming in this blended “alkaline-belite” cement (as it was determined through XRD, 29Si and 27Al MAS NMR and electron microscopy) consisted in a mix of cementitious gels: C-(A)-S-H and N-(C)-A-S-H, which interacted and over time evolved toward the latter with no detriment to the mechanical strength developed by the cement., This research was funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects BIA2016-76466-R and RTC2016-4872-S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Efecto del contenido de C3A en los cementos híbridos

  • Regidor, P.
  • Maltseva, O.
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
Póster presentado a las II Jornadas de Jóvenes Científicos en Materiales de Construcción, celebradas en Madrid del 27 al 28 de mayo de 2019., Los cementos híbridos son unos cementos con muy bajo contenido de cemento portland (< 30%) y elevados contenidos de ceniza volante (<70%). Para acelerar el desarrollo de las resistencias iniciales se incorpora un activador alcalino (< 5%). El objetivo de este trabajo es determinar cómo influye el tipo de cemento empleado en la elaboración de cementos híbridos, más concretamente el contenido de C3A del cemento. Para este estudio se han empleado dos cementos comerciales: A=CEM I 52,5 R y B=CEM I 52,5 SR. Con ellos se elaboraron dos cementos híbridos: HYCA (27.5 % CEM I 52,5 R + 67.5 %5 % ceniza volante +5% activador) y HYCB (27.5 % CEM I 52,5 SR + 67.5 %5 % ceniza volante +5% activador). Inicialmente se determinaron las resistencias mecánicas en pasta, los tiempos de fraguado, y el calor liberado por calorimetría de conducción isoterma. Las pastas fueron caracterizadas por DRX y FTIR a 28 días. Finalmente se elaboraron hormigones a 2 y 28 días. Los resultados obtenidos muestran que, de los dos cementos híbridos, el que tiene un mayor contenido de C3A da lugar a cementos con tiempos de fraguado más cortos, y mayores resistencias iniciales., Ministerio de Ciencia Innovación y Universidades y fondos FEDER que subvencionan los proyectos BIA2016-76466-R y RTC2016-4872-S. Gracias también al MINECO y UE por la subvención del contrato de iniciativa al empleo Juvenil EI-GARJUV-GP17-0045 CAMGP17-IETCC_001.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Hidratación del Clinker de sulfoaluminato de calcio (CSA) en medio alcalino

  • Padilla Encinas, Pilar
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
Póster presentado a las II Jornadas de Jóvenes Científicos en Materiales de Construcción, celebradas en Madrid del 27 al 28 de mayo de 2019., Los cementos de sulfoaluminato de calcio (CSA) se caracterizan por estar formados principalmente por ye¿elemita (C4A3Š). Estos cementos se consideran medioambientalmente más sostenibles que el OPC, debido a que la temperatura de su fabricación (1300ºC) es unos 300º menor que la del cemento portland (OPC). Dichos cementos se caracterizan por presentar una rápida velocidad de fraguado y endurecimiento, y un buen desarrollo de resistencias mecánicas a edades iniciales. Cuando se hidratan con agua en presencia de sulfato cálcico, se forma etringita e hidróxido de aluminio2. Pero cuando el Clinker de CSA se hidrata, en ausencia de sulfatos, dependiendo de la cantidad de agua utilizada, se puede obtener como productos de reacción etringita, monosulfato, C3AH6 y AH3. Este trabajo se ha estudiado como afecta la presencia de álcalis a la hidratación de un Clinker de CSA comercial (en ausencia de sulfato cálcico). Para ello el Clinker se hidrato con agua (referencia) y con disoluciones de NaOH (0.1M, 2M, y 4M). Se determinaron las resistencias mecánicas en probetas prismáticas de pasta a 2, 28 y 90 días. La velocidad de desprendimiento de calor se determinó por calorimetría de conducción isoterma, y los productos de reacción se han caracterizado por DRX, FTIR y SEM/EDX. Los resultados obtenidos indican que a medida que aumenta la concentración de NaOH en el medio, las resistencias mecánicas disminuyen debido principalmente a la formación de productos de reacción diferentes: Katoita, carboaluminatos y ternardita., Esta investigación fue desarrollada gracias al apoyo del Ministerio de Ciencia e Innovación y Universidades y fondo FEDER que subvencionan el proyecto BIA2016‐76466‐R, y la beca FPI (BES-2017-082022).
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

New alkaline-belitic hybrid binders

  • Palomo, Ángel
  • Fernández-Jiménez, Ana
  • Sánchez-Herrero, M. J.
Trabajo presentado al 15th International Congress on the Chemistry of Cement (ICCC), celebrado en Praga (República Checa) del 16 al 20 de septiembre de 2019., This paper summarises a long-term study organized in two consecutive steps. The first, which involved exploring a number of laboratory-synthesised belite clinkers with slightly different mineral compositions in depth, culminated in the industrial-scale manufacture of one of those materials. In the second a hybrid alkaline belite cement was prepared containing 48 % of the industrial belite clinker, 48 % fly ash and 4 % chemicals. The hybrid binder was subsequently analysed to determine its mechanical strength and hydration products. The findings showed that the hybrid alkaline belite cement designed met the compositional, mechanical and setting time requirements laid down in European standard EN 197-1 and that its hydration favoured the simultaneous precipitation of a mix of cementitious gels: C-(A)-S-H and N-(C)-A-S-H., This research was funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects BIA2016‐76466‐R and RTC2016‐4872‐S.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Mechanochemical activation of fly ashes a way to make concretes with high levels of substitution: hybrid concretes

  • Cabrera, Oscar
  • Viejo-Mariño, David
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
  • Maltseva, O.
Trabajo presentado al 15th International Congress on the Chemistry of Cement (ICCC), celebrado en Praga (República Checa) del 16 al 20 de septiembre de 2019., The objective pursued in this study was to determine the mechanical properties and some technological characteristics of a few concrete formulations containing a high level of fly ash. Three concrete options were considered with respect the fly ash addition: i) concrete TO (prepared by adding original fly ash); ii) concrete TM (prepared with mechanically activated fly ash); iii) concrete TMA (prepared with mechano-chemical activated fly ash). The pozzolanic activity of the fly ash as function of the type of activation procedure (TO, TM or TMA) was determined by the Frattini method and also by the Activity Index. The effect of the fly ash in the hydration kinetics was also determined by conduction calorimetry. Finally the effect in the mechanical strength development was determined in a H-30 concrete. Results of this research indicate that the mechano-chemical treatment of the fly ash (TMA), allows to develop a compressive strength of 30 MPa at 28 days for a replacement level (fly ash for OPC) of 50%., This research was funded by the Spanish Ministry of the Economy and Competitiveness and funds FEDER under research projects BIA2013-43293-R and BIA2016-76466-R.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Role of ternesite on the hydration of C3A in the presence and absence of gypsum

  • Montes, Myriam
  • Pato, Esther
  • Carmona-Quiroga, Paula
  • Blanco-Varela, María Teresa
Trabajo presentado al 15th International Congress on the Chemistry of Cement (ICCC), celebrado en Praga (República Checa) del 16 al 20 de septiembre de 2019., In the search for new eco-cements it has been found that ternesite (2C2S·CaSO4), which has traditionally been regarded as a hydraulically inactive phase, can be activated by aluminum hidroxides (AH3) and some calcium aluminates. This research, in particular, studies the role of ternesite on C3A hydration, with and without gypsum. After laboratory synthesis, C3A was blended with ternesite, gypsum and ternesite+gypsum. The early hydration of those blends was monitored with isothermal conduction calorimetry at 25 °C for 7 days. The resulting pastes were analysed with XRD, FTIR and DTA/TG. Additionally, mixtures of C3AH6 and ternesite in water were prepared in order to study their compatibility. The calorimetric results showed a higher total heat per gram of aluminate in the sample containing gypsum and ternesite than in the sample C3A+ternesite. XRD diffractograms and DTG-TG analysis revealed the presence of AFm in all the samples with gypsum but not in C3A+ternesite which shows no evidence of ternesite activation by C3A., Funding from BIA2016-76466-R project as well as the Regional Government of Madrid Community and European Social Fund (Geomaterials Programme2 S2013/MIT-2914) is gratefully acknowledged. Authors thank to Ministerio de Economía y Competitividad the young researcher contract given to Myriam Montes. Financial support for Dr. Paula M. Carmona-Quiroga’s participation was provided by the Spanish Ministry of the Economy and Competitiveness under project BIA2015-73237-JIN.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Contribución de congreso (ConferenceOutput)

Effect of curing temperature in the hydration of a belite cement with high level of fly ash

  • Qu, Bo
  • Sánchez-Herrero, M. J.
  • Martín, Antonia
  • Pastor, José Y.
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
Trabajo presentado al 15th International Congress on the Chemistry of Cement (ICCC), celebrado en Praga (República Checa) del 16 al 20 de septiembre de 2019., This study aimed to determine the physical, mechanical, mineral and microstructural properties of a industrially manufactured hybrid cement (HYP), consisting 47,5 % Belite clinker + 47,5 % FA + 5 % solid alkaline activator. The effect of the curing temperature (25ºC, or 85 ºC) on hydration kinetics and on compressive strength development (in paste prisms and mortar prisms) was determined. Isothermal conduction calorimetry shows that curing at 85ºC, accelerates relevantly the hydration process. The 3 days compressive strength achieved by curing at 25oC was 9 MPa, but 30 MPa was the mechanical strength after 3 days if mortars were cured at 85ºC. After 28 days, the compressive strength of the specimen cured at 25oC was 33 MPa, and 43 MPa after 90 days. The specimens cured at 85oC exhibited a slightly better compressive strength. The hydration products formed were characterized using XRD, SEM/EDX and 27Al and 29Si MAS-NMR. The main reaction product formed was found to be a mixture of cementitious gels: C-(A)-S-H /C-A-S-H/(N,C )-A-S-H. The initial curing at 85°C for 20 h inhibited the formation of ettringite (or favored its rapid decomposition), at least during the first 90 days (maximum age of the materials analyzed in this work). On the contrary, curing at 85ºC favors the precipitation of the sulphates in the form of Phase U., This research was funded by the Spanish Ministry of the Economy, Industry and Competitiveness and FEDER under research projects BIA2016-76466-R and RTC2016-4872-S, Ministry of Economy and Competitiveness of Spain (MAT2015-70780-C4-4-P), and Community of Madrid (S2013/MIT-2862-MULTIMATCHALLENGE). Author QuBo, a Ph.D. the student worked under a China Scholarship Council (CSC) grant.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Can calcium aluminates activate ternesite hydration?

  • Montes, Myriam
  • Pato, Esther
  • Carmona-Quiroga, Paula
  • Blanco-Varela, María Teresa
Aluminum hydroxide (AH3) has recently been shown to be able to activate hydration in ternesite, a phase found in some calcium sulfoaluminate (CSA) cements. This study explored the capacity of a number of calcium aluminates (C3A, C12A7, CA and C4A3) to activate ternesite hydraulic reactivity. After laboratory synthesis, the aluminates were blended with ternesite at a ratio of 1:2 and their hydration was monitored with isothermal conduction calorimetry for 7 days at 25 °C. The resulting pastes were analysed with XRD, FTIR and DTA. The presence of ternesite in the pastes altered the aluminate heat flow curves, shortening the induction period and bringing the reaction peak forward, an indication of hastened hydration. Ternesite also altered the reaction products, which included calcium monosulfoaluminate hydrate and strätlingite., This paper has been funded from BIA2016-76466-R project as well as the Regional Government of Madrid Community and European Social Fund (Geomaterials Programme2 S2013/MIT-2914). Authors thank to Ministerio de Economía y Competitividad the young researcher contract given to Myriam Montes. Financial support for Dr. Paula M. Carmona-Quiroga's participation was provided by the Spanish Ministry of the Economy and Competitiveness under project BIA2015-73237-JIN., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hybrid alkaline cements: Bentonite-Opc binders

  • García-Lodeiro, Inés
  • Fernández-Jiménez, Ana
  • Palomo, Ángel
This article belongs to the Special Issue Geopolymers., Moderately alkaline activators can be used to formulate cementitious binders with a high Supplemetary Cementitious Materials (SCMs) and a low portland cement content (hybrid alkaline cements). This study aimed to prepare hybrid alkaline cements containing large percentages of dehydroxylated bentonite (BT) and small Portland cement (OPC) fractions, with 5% Na2SO4 as a solid alkaline activator. The hydration kinetics of the pastes hydrated in water in the presence and absence of the solid activator were assessed by isothermal conduction calorimetry, whilst the reaction products were characterised with X-Ray Powder Diffraction (XRD) and Fourier-transform Infrared Spectroscopy (FTIR). The presence of the alkaline activator hastened OPC and BT/OPC hydration: more heat of hydration was released, favouring greater initial bentonite reactivity. The portlandite forming during cement hydration reacted readily with the Na2SO4, raising medium alkalinity and enhancing bentonite dissolution and with it reaction product precipitation (primarily (N,C)-A-S-H-like gels that co-exist with C-S-H- or C-A-S-H-like gels). The presence of sulfate ions favoured the formation of AFm-like phases. Preceding aspects accelerated the hydration reactions, with the formation of more reaction product and matrix densification. As a result, the 28 days Na2SO4 activated systems developed greater mechanical strength than the water-hydrated systems, with the 60% BT/40% OPC blends exhibiting higher compressive strength than the 100% OPC pastes., This research was funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects BIA2016-76466-R and RTC2016-4872-S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Hydration mechanisms of hybrid cements as a function of the way of addition of chemicals

  • Fernández-Jiménez, Ana
  • García-Lodeiro, Inés
  • Maltseva, O.
  • Palomo, Ángel
In this study fly ash contents of up to 50% were used to produce binders with mechanical strength greater than or equal to type CEM I 42.5R cement (reference). The specific aim pursued in this research was to determine whether the procedure used to add the chemical activator (in solid or liquid form) can affect strength development in the cement or the nature of the reaction products formed. Two experimental procedures were deployed: (a) the chemical activator was dissolved in the mixing water; (b) the chemical activator was ground, as a solid, into the fly ash. The solid‐state method induced slightly higher mechanical strength than when the activator was dissolved in hydration water. The way the chemical activator was added affected not only early age reaction kinetics, but also the nature and composition of the reaction products, the liquid state favoring the formation of phases AFt and AFm., This research was funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects BIA2016‐76466‐R and RTC2016‐4872‐S., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Reuse of waste sandstone sludge via alkali activation in matrices of fly ash and metakaolin

  • Clausi, Marina
  • Fernández-Jiménez, Ana
  • Palomo, Ángel
  • Tarantino, Serena C.
  • Zema, Michele
This work aims at investigating the possibility of reusing sludge from sandstone sawing in alkaline cements. In particular, the behaviour towards alkali activation process of Pietra Serena sludge (sPS), either alone or in binary mixtures with class F fly ashes and metakaolin, was evaluated. The binders were synthesised with 8 M and 12 M NaOH solutions and cured at 85 °C for 5 or 20 h. Mechanical strength was determined after one day and the reaction products were characterized by XPRD, FTIR and SEM/EDX. Also colorimetry tests were performed. The alkali activation of sPS gives a material with limited amount of amorphous gel, in which unreacted particles can be still recognized, and showing a compressive strength of 3.6(2) MPa. The use of fly ashes and metakaolin in different proportions enhances mechanical strength up to 36(2) MPa. In these blends, the sludge acts basically like a filler. However, calcium carbonates present on the sludge partially dissolve and react in the alkaline mixture favouring the formation of some local high-calcium, high Si/Al ratio (C-A-S-H-type gel) areas co-existing with N-A-S-H-type gel., MC has been supported by Ministero dell’Istruzione, dell’Università e della Ricerca scholarship (Fondo per il sostegno dei giovani). This research was also funded by the Spanish Ministry of the Economy and Competitiveness and FEDER under research projects, BIA2016-76466-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Use of clays in alkaline hybrid cement preparation. The role of bentonites

  • García-Lodeiro, Inés
  • Boudissa, Nassima
  • Fernández-Jiménez, Ana
  • Palomo, Ángel
‘Portland-alkaline’ hybrid cements (HYC), the latest generation of alkaline cements, are multi-component systems consisting in blends with high mineral addition and low portland cement contents. In the presence of alkaline activators, these systems set and harden into materials with excellent cementitious properties. This study explored the 2 and 28 day mechanical strength of a series of hybrid cements comprising blends with different proportions of portland cement (OPC) and dehydroxylated bentonite (BT). The reaction products were characterised with XRD and BSEM/EDX. The presence of an alkaline salt activator hastened reaction product precipitation and favoured strength development., This study was funded by a research grant (BIA 2016-76466-R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Tesis doctoral (DoctoralThesis)

Temperature effect on performance of Portland cement versus advanced hybrid cements and alkali-Fly ash cement

  • Qu, Bo
[ES]: El objetivo principal de este trabajo es estudiar el efecto de la temperatura en diferentes conglomerantes con un bajo contenido de clinker y elevados contenidos de adiciones minerales (“Suplementary cementitious materials”, SCMs), contenidos superiores a los contemplados en los cementos compuestos (Blended cement). Esos nuevos materiales han sido considerados como una de las posibles soluciones para enfrentar el problema ambiental causado por la industria tradicional del cemento, especialmente las emisiones de CO2. En concreto los conglomerantes estudiados han sido: i) OPC: cemento Portland comercial tipo CEM I 42.5 como referencia; ii) HYC: cementos alcalinos híbridos preindustrial compuesto de un 30% de clinker de cemento Portland y un 70% de SCMs (mezcla de escoria, cenizas volantes y activador sólido (en diseño); iii) HYP: cemento preindustrial compuesto por un 50% de Clinker de cemento belitico, y 50% de cenizas volantes junto a una pequeña fracción de activador sólido (en diseño); iv) FAN: cenizas volantes activadas alcalinamente (sin Clinker), como activador se empleó una disolución de NaOH 8M (referencia). La investigación se ha centrado en el estudio del efecto de la temperatura en el proceso de hidratación temprana (en el proceso de pre-curado), así como, en el efecto de la exposición de las pastas endurecidas a elevadas temperatura (entre 200 y 1000 ºC) En primer lugar, se estudió como la temperatura de curado en las primeras 20 horas (25 ± 1 o 85 °C d) afecta a la hidratación inicial de estos materiales aglutinantes. Se exploró el efecto de la temperatura de curado inicial sobre la cinética de hidratación y el desarrollo de resistencias mecánicas a 2 y 28 días. También se determinó su efecto sobre los productos de reacción formados y la microestructura desarrollada. Los productos de hidratación formados se caracterizaron usando XRD, SEM/EDX y 27Al y 29Si MAS-NMR. Los resultados obtenidos mostraron que HYC y HYP al hidratarse con agua a temperatura ambiente (25 ± 1 ºC) fraguan y endurecen alcanzando unos valores de resistencia mecánica a compresión superior a 30 MPa, a los 28 días. El principal producto de reacción formado fue una mezcla de geles cementosos: C-(A)-S-H y C-A-S-H para HYC y una mezcla de C-(A)-S-H, C-A-S-H y (N,C)-A-S-H para HYP. Curando a 85 °C durante 20 horas, presentaron un comportamiento similar al OPC, inhibieron la formación de ettringita y generaron geles más polimerizados, mejorando la resistencia mecánica de tres días, pero no de 28 o 90 días. En segundo lugar, en lo que respecta al comportamiento de las pastas endurecidas a elevadas temperaturas (desde 200 hasta 1000 ºC), se realizaron dos tipos de ensayos: (1) ensayo para determinar la resistencia mecánica, el módulo elástico y la tenacidad a la fractura de los materiales hasta 1000 ºC “in situ” y (2) prueba para evaluar el comportamiento post-tratamiento térmico después de 2 horas de exposición a temperaturas que van desde 400 ºC a 1000 ºC. Los cambios mineralógicos y micro-estructurales que tienen lugar en los materiales se estudiaron por XRD, SEM/EDX y 27Al y 29Si MAS-NMR, DTA / TG. Los cambios en la distribución del tamaño de poro de las pastas cementantes también fueron estudiados por MIP después del calentamiento a temperaturas ≥ 600 ºC. Los resultados obtenidos muestran que las pastas OPC perdieron totalmente la resistencia entre 400 y 600 ºC, sin embargo, las pastas de HYC e HYP presentaron una mejor resistencia a altas temperaturas que las pastas cementantes OPC. La pasta FAN mostró buena resistencia residual después de su exposición al calor. Sin embargo, a temperaturas superiores a 800 ° C, presenta un importante evento de contracción (especialmente en la prueba in situ) y grandes cambios en la porosidad, que se asoció con un proceso de sinterización parcial y la formación de nuevas fases minerales. Las diferentes fases formadas en los cementos en función de la temperatura de exposición se asocian con la diferente composición química de los cementos de partida y también con la diferente composición y microestructura del gel o geles mixtos que se formaron durante la hidratación. Los resultados obtenidos con los cuatro materiales cementantes estudiados pueden dar una idea general de la relación entre la composición elemental y el rendimiento a altas temperaturas. Será un factor importante a tener en cuenta al determinar el rendimiento a alta temperatura de futuros cementos y hormigones. Resumiendo, los hallazgos de este trabajo mostraron que cementos con bajos contenidos en Clinker pueden ser manufacturarse industrialmente. Estos cementos con elevados contenidos de SCMs en presencia de un activador alcalino (solido) presentan un desarrollo mecánico adecuado y pueden tener un mejor comportamiento a elevadas temperaturas que los cementos tradicionales de OPC., [EN]: The main objective of this work is to study the effect of temperature on some specific cementitious binder materials with low clinker content and higher supplementary cementitious materials (SCMs) than blend cements. Those novel materials have been considered as one of potential solution to face environment issue caused by traditional cement industry especially CO2 emission. Specifically cements studied were: i) OPC: A commercial Portland cement Type CEM I 42.5R as reference; ii) HYC: pre-industrial hybrid alkaline cements contain 30 % of Portland cement clinker, 70 % mix of slag, fly ash and little solid activator (in design); iii) HYP: Pre-industrial cement: 50 % belite cement clinker and 50 % mix of fly ash and little solid activator (in design); iv) FAN: Alkali-activated fly ash binder (free clinker, activated by sodium hydroxide, as reference). Research has focused on the study of the effect of temperature on the early hydration process (in the pre-cure process), as well as on the effect of high temperature on hardened pastes (between 200 and 1000 ºC). First, it was studied how the curing temperature in the first 20 hours (25 ± 1 or 85 ° C d) affects the initial hydration of these binder materials. The effect of the initial curing temperature on the hydration kinetics and the development of mechanical resistance at 2 and 28 days were explored. Its effect on the reaction products formed and the developed microstructure was also determined. The hydration products formed were characterized using XRD, SEM / EDX and 27Al and 29Si MAS-NMR. The results obtained showed that HYC and HYP when hydrated with water at room temperature (25 ± 1 C) set and harden reaching mechanical compressive strength values over 30 MPa, at 28 days. The main reaction product formed was a mix of cementitious gels: C-(A)-S-H and C-A-S-H for HYC and a mix of C-(A)-S-H, C-A-S-H and (N, C)-A-S-H for HYP. Curing at 85C for 20 hours, they performed behaviour similar to OPC, inhibited ettringite formation and generated more polymerised gels, enhancing 3-day but not 28- or 90-day mechanical strength. Secondly, with regard to the behaviour of the hardened pastes at high temperatures (from 200 to 1000 ºC), two types of tests were carried out: (1) trial to determine the mechanical strength, the elastic modulus and the fracture toughness of materials up to 1000 ºC “in situ” and (2) trial to evaluate post-thermal behaviour after two hours of exposure to temperatures ranging from 400 ºC to 1000 ºC. The mineralogical and micro-structural changes that take place in the materials were studied by XRD, SEM/EDX and 27Al and 29Si MAS-NMR, DTA/TG. The changes in the pore size distribution of the cementing pastes were also studied by MIP after heating at temperatures ≥ 600 ° C. The OPC pastes totally lost the resistance between 400 and 600 ºC; however, the pastes of the HYC and HYP performed better high-temperature resistance than the OPC cementitious pastes. The FAN paste showed good residual strength after heat exposure. However, at temperatures above 800 ° C, it presents an important event of contraction (especially in the in situ test) and large changes in porosity, which was associated with a partial sintering process and the formation of new mineral phases. The different phases formed in the cements as a function of the exposure temperature are associated with the different chemical composition of the starting cements and also with the different composition and microstructure of the gel or mixed gels that were formed during hydration. The results obtained with the four cementitious materials studied can give a general idea of the relationship between elemental composition and high temperature performance. It will be an important factor to consider when determining the high temperature performance of future cement and concrete. In summary, the findings of this work showed that cements with low Clinker content can be manufactured industrially. These cements with high contents of SCMs in the presence of an alkaline activator (solid) have a suitable mechanical development and can have a better behaviour at high temperatures than traditional OPC cements., Gobierno de España: BIA2013-43293-R - Cementos híbridos: síntesis e hidratación; BIA2016-76466-R -CSIC - Avances en ciencia y tecnología de cementos híbridos- sostenibles. Universidad Politécnica de Madrid. China Scholarship Council and Universidad Politécnica de Madrid for providing scholarship, Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of alkalis content on calcium sulfoaluminate (CSA) cement hydration

  • Tambara Jr, L.U.D.
  • Cheriaf, Malik
  • Rocha, J. C.
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
The behavior of sulfoaluminate (CSA) cements hydrated in neutral or alkaline solutions (0 M, 0.1 M, 1 M, 4 M and 8 M NaOH) was studied. 2-d, 28-d and 90-d mechanical strengths were determined, as well as the reaction rate by isothermal conduction calorimetry. The reaction products were characterised with XRD, DTA and SEM. The findings revealed differences in performance depending on whether hydration transpired at pH ≤ 14 (0.1 and 1 M) or pH > 14 (4 M and 8 M). To 0.1 M and 1 M, there is an improvement of mechanical strength than in water-hydrated pastes. The majority reaction products in these conditions were ettringite and microcrystalline aluminium hydroxide. Mechanical strength was lower in the high alkalinity (4 M and 8 M) than in the reference pastes, mainly due to the formation of different reaction products. Ettringite was unstable at 4 M and failed to form at 8 M, whilst thenardite and U-phase were detected in the 28d and later materials hydrated at both concentrations., This study was partially supported by the Brazilian National Council for Scientific and Technological Development (CNPq) under project 208380/2017-5, and CAPES. Financial support for this study was also furnished by the Spanish Ministry of the Economy and Competitiveness and FEDER under research project BIA2016-76466-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Replacing fly ash with limestone dust in hybrid cements

  • Millán-Corrales, G.
  • González-López, J. R.
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
This study explored the effect of adding 10% of finely ground limestone dust to alkaline hybrid cements. A series of binders was prepared with 20–30% OPC (CEM I 52.5R) and fly ash in the presence or absence of a chemical activator (5% Na2SO4). The rate of heat release was determined by isothermal conduction calorimetry. Setting times and 3 d, 28 d and 90 d compressive strength were likewise found. The reaction products were characterised by XRD, DTA/TG and BSEM/EDX. The inclusion of 10% of limestone in the hybrid cements to replace the fly ash improved compressive strength and hastened hydration. The 28 d pastes containing 30% OPC, 10% limestone, 55% FA and 5% Na2SO4 developed compressive strength above 45 MPa., This study was partially supported by the Universidad Autonóma de Nuevo León and Mexico’s Consejo Nacional de Ciencia y Tecnología (CONACYT), which funded Eng. G. Millán’s residency as an Engineering PhD. student (with Orientation in Construction Materials) at the Eduardo Torroja Institute. Further funding was provided by the Spanish Ministry of the Economy and Competitiveness and FEDER (project BIA2016‐76466‐R)., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Use of industrial by-products as alkaline cement activators

  • García-Lodeiro, Inés
  • Cristelo, Nuno
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
Alkaline (or geopolymer) cements have proven to be a sustainable alternative to the ordinary portland cement material. The laboratory reagents normally used as alkaline activators constitute the most costly and on occasion polluting constituents of such cementitious systems. This study aimed to explore the use of a disposed cleaning solution (CS), coming from the aluminium transformation industry, as an activator for high and low calcium aluminosilicate precursors. For that a Blast Furnace Slag (BFS) and a type F-Fly Ash (FA) were used. Precursors activated with a traditional NaOH solutions were used as a reference. Kinetics of reactions (isothermal calorimetry) were evaluated and mechanical strength of hardened pastes determined. The nature of the reaction products generated in this new systems were also identified by using XRD, FTIR, SEM and 29Si and 27Al MAS NMR. The findings showed that the CS can be effectively used to prepare cementitious materials, particularly when applied to CaO-SiO2-Al2O3 system precursors such as BFS, which require lower alkalinity than FA-based precursors. The nature of the reaction products generated in the CS alkali activated systems was similar than those observed in the reference systems, however Al richer reaction products were observed in the former., This research was funded by the Spanish Ministry of Science, Innovation and Universities under project BIA2016-76466-R and ERDF under project RTC2016-4872-S (principal investigators Angel Palomo and Ana Fernandez-Jimenez). In addition, thanks the project from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 734833., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

ZnO Nanoparticles for Photocatalytic Application in Alkali-Activated Materials

  • Guzmán-Carrillo, H. R.
  • Manzano-Ramírez, Alejandro
  • García-Lodeiro, Inés
  • Fernández-Jiménez, Ana
This article belongs to the Special Issue Advances in Alkali-Activated Materials., This paper reports an Alkali-Activated Materials (AAM) using two different precursors, metakaolin and a metallurgical slag with photocatalytic zinc oxide nanoparticles, as novel photocatalytic composites. The photodegradation performance of the composites using methylene blue (MB) dye as a wastewater model was investigated by ultraviolet radiations (UV-vis) spectroscopy. Adsorption in dark conditions and photodegradation under UV irradiation are the mechanisms for removing MB dye. The pseudo-first-order kinetic and pseudo-second-order kinetic models were employed, and the experimental data agreed with the pseudo-second-order model in both cases with UV and without UV irradiations. As new photocatalytic materials, these composites offer an alternative for environmental applications., This research was partially funded by CONACyT (National Council for Science and Technology) grant number 397245 and by the Spanish Ministry of the Economy, Industry and Competitiveness and ERDF under project BIA2016-76466-R., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Low-Calcium, Porous, Alkali-Activated Materials as Novel pH Stabilizers for Water Media

  • Palomo, Ángel
  • Fernández-Jiménez, Ana
Due to the increase of water consumption, water treatment systems become more actual and innovative materials for water treatment are welcomed. Traditionally, alkalizing agents, such as lime or caustic soda, have been employed to increase the pH levels, which induce chemical clarification of wastewater. Some innovative ideas of using low-calcium, alkali-activated materials (AAM) for this purpose have been considered previously. In this study, the low-calcium, porous, alkali-activated material (pAAM) was characterized to understand the impact of the aluminum silicate source and heat treatment on basic properties for material that might be used in water treatment systems as a softener by stabilizing the pH. The studied porous alkali-activated materials may ensure stable and long-lasting (30 days) pH (pH 10.3¿11.6) in water media depending on the composition and amount of activation solution used for AAM preparation. Heat treatment does not have an impact on the mineralogical composition and structural properties of the pAAM, but it does change the leaching ability of alkalis from the material structure., Ministry of Economy, Industry and Competitiveness of Spain under the project [BIA2016-76466-R], Riga Technical University (Latvia) Erasmus+ projects [No 2016-1-LV01-KA103-022512 and No 2015-1-LV01-KA103-013255], and Riga Technical University’s Doctoral Grant Program.
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Monitoring early hydration of calcium sulfoaluminate clinker

  • Padilla Encinas, Pilar
  • Palomo, Ángel
  • Blanco-Varela, María Teresa
  • Fernández-Carrasco, Lucía
  • Fernández-Jiménez, Ana
Initial hydration and setting were continuously monitored in calcium sulfoaluminate clinker (KCSA) mixed with water or 2 M NaOH with isothermal conduction calorimetry, ultrasonic pulse velocity (UPV) measurement, the Vicat apparatus, and (in- and ex-situ) X-ray diffraction. P-wave acceleration (ap) proved highly useful to detect very rapid initial reactions, not generally perceptible with other techniques. Setting in the water-hydrated KCSA pastes was mediated by ettringite formation. Flash setting due to calcium aluminate hydrate precipitation was observed in the 2 M NaOH-hydrated clinker. Ye'elemite reacted most intensely at later times in both pastes, inducing AFt and AH precipitation and the formation of smaller proportions of other calcium aluminate hydrates that densified the matrix., This research was developed thanks to the support of the Min-istry of Science and Innovation and Universities and FEDER fundsthat subsidize the Project BIA2016-76466-R and the aid BES-2017-082022. In addition, the PhD student Pilar Padilla-Encinas, thanks to the University Autónoma of Madrid, to be able to carryout her thesis in the Applied Chemistry program
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of alkaline salts on calcium sulfoaluminate cement hydration

  • Urbano Durlo Tambara Júnior, Luís
  • Rocha, Janaíde C.
  • Cheriaf, Malik
  • Padilla Encinas, Pilar
  • Fernández-Jiménez, Ana
  • Palomo, Ángel
This work analyzes the effect of the presence of 5 wt.% of solid sodium salts (NaSO, NaCO, and NaSiO) on calcium sulfoaluminate cement (CSA) hydration, addresses hydration kinetics; 2-, 28-, and 90-d mechanical strength, and reaction product microstructure (with X-ray diffraction (XRD), and Fourier transform infrared spectroscopy, (FTIR). The findings show that the anions affect primarily the reactions involved. Ettringite and AH, are the majority hydration products, while monosulfates are absent in all of the samples. All three salts hasten CSA hydration and raise the amount of ettringite formed. NaSO induces cracking in the ≥28-d pastes due to posthardening gypsum and ettringite formation from the excess SO present. Anhydrite dissolves more rapidly in the presence of NaCO, prompting carbonation. NaSiO raises compressive strength and exhibits strätlingite as one of its reaction products., This study was partially supported by the Brazilian National Council for Scientific and Technological Development (CNPq) under projects 208380/2017‐5 and 151890/2020‐0, and CAPES. Financial support was also furnished by the Spanish Ministry of the Economy and Competitiveness and FEDER under research project BIA2016‐76466‐R and funding from BES‐2017‐082022. PhD. student Pilar Padilla‐Encinas thanks the Autonomous University of Madrid for the opportunity to complete her thesis in its Applied Chemistry program. The cement supplied by Heidelberg Cement Hispania is gratefully acknowledged
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Up to 100% Replacement of Natural Materials from Residues: Recycling Blast Furnace Slag and Fly Ash as Self-Leveling Cementitious Building Materials

  • Torrens-Martín, David
  • Fernández-Carrasco, Lucía
  • Blanco-Varela, María Teresa
The objective of this research is to study the use in the construction industry of recycled slag (SL) and fly ash (FA) using from 0.1 to 5% calcium sulfate (wCS¯). These wastes have been used to make ternary mixture systems and evaluated in terms of technological properties as cementitious materials for building applications. Studying their micro-structure as hydration products, setting times and mechanical properties shows a way to develop new mixtures from high proportion of waste, which are alternatives to the traditional nature ternary systems: Portland cement (PC), calcium aluminate cement (CAC) and calcium sulphate (CS¯). Based on previous work with natural products, the selected SL/FA ratios were 9 and 2.3 and the sulphate contents were 0, 1 and 5%. The water/binder ratio used for these cementitious mixes was 0.4. The specimens prepared for strength determination were prisms of 10 × 10 × 60 mm. The pastes were prepared and cured at 20 °C and 98% relative humidity for 1 day and then either stored at 20 °C at 98% humidity (dry) or immersed in distilled water (wet) for 14 and 28 days. The results showed that both FA and SL mixed with CS¯ produce ettringite after 28 days of setting, and this phase was the main crystalline hydrated product in all mixes. Calcium sulphate stimulates the hydration reactions of the mixes and the strength increases when the CS¯ content is higher due to ettringite formation, while the setting time decreases, as happened in the systems prepared with natural materials., Funding for this study was provided by the Agaur 2017 SGR 29 I+D+I project and the MICINN (Ministerio de Ciencia e Innovación) for supporting this research through the BIA 2016-76466R project., Peer reviewed
DIGITAL.CSIC. Repositorio Institucional del CSIC
Publication Artículo científico (JournalArticle)

Effect of Na versus Ca Sulfate Salts on the Hydration of Calcium Sulfoaluminate Clinker

  • Padilla Encinas, Pilar
  • Palomo, Ángel
  • Fernández-Jiménez, Ana
This paper examined how the amount (5% or 20%) and type (CaSO or NaSO) of sulphate salt affect the hydration of calcium sulphoaluminate clinker (KCSA). The mechanical behavior of the pastes was determined at 1, 3, 28, and 90 days, the heat flow and total heat were measured with isothermal conduction calorimetry, and the reaction products were characterized using X-ray diffraction (XRD), differential thermal analysis/thermogravimetry (DTA/TG) and scanning electron microscopy (SEM). The results obtained indicated that both the amount of sulphate salt (5% or 20%) and its type (CaSO or NaSO) affect the hydration kinetics, type of reaction products formed, and development of mechanical strength. The incorporation of CaSO has a positive effect on the development of the mechanical strength of KCSA. However, NaSO can also produce adverse side effects at older ages. The presence of NaSO increases pH values, which partly destabilizes the ettringite formed, thereby favoring carbonation and thenardite precipitation, which can cause the specimens to crack and break., Peer reviewed
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Effect of alkalinity on early-age hydration in calcium sulfoaluminate clinker

  • Padilla, Patricio
  • Fernández Carrasco, Lucía
  • Palomo Sanchez, Ángel
  • Fernández Jiménez, Ana
Early-age hydration with neutral or alkaline (0 M to 8 M) solutions was studied in calcium sulfoaluminate clinker (CSA) using isothermal conduction calorimetry, X-ray diffraction (both continuous and discontinuous, i.e., after detaining hydration with isopropanol) and infrared spectroscopy. Hydration in 0.1 M NaOH was observed to be similar to hydration in water. At the next highest concentration studied (1 M), however, the reaction rate was slower, due primarily to lower AFt stability in that medium. Faster hydration but less total heat was observed in the pastes hydrated with 2 M NaOH, a finding associated with the presence of a metastable compound, U-phase, that subsequently transitioned to AFt, C3AH6 and thenardite. Hydration with highly alkaline (4 M and 8 M) solutions inhibited AFt formation completely, although ye'elimite reacted more vigorously (particularly with 8 M NaOH) to form katoite, AH3 and thenardite., Funding for this study was provided by the Spanish Ministry of Science, Innovation and Universities and ERDF under project BIA2016-76466-R and grant BES-2017-082022. PhD. student Pilar Padilla-Encinas benefited from the support of the Universidad Autónoma of Madrid to perform the research for her thesis through the IETcc's Applied Chemistry Programme. The cement supplied by HeidelbergCement Hispania is gratefully acknowledged., Peer Reviewed, Postprint (author's final draft)
Recercat. Dipósit de la Recerca de Catalunya
Publication Artículo científico (JournalArticle)

Up to 100% replacement of natural materials from residues: recycling blast furnace slag and fly ash as self-leveling cementitious building materials

  • Torrens Martín, David
  • Fernández Carrasco, Lucía
  • Blanco Varela, M.Teresa
The objective of this research is to study the use in the construction industry of recycled slag (SL) and fly ash (FA) using from 0.1 to 5% calcium sulfate (wCS¯). These wastes have been used to make ternary mixture systems and evaluated in terms of technological properties as cementitious materials for building applications. Studying their micro-structure as hydration products, setting times and mechanical properties shows a way to develop new mixtures from high proportion of waste, which are alternatives to the traditional nature ternary systems: Portland cement (PC), calcium aluminate cement (CAC) and calcium sulphate (CS¯). Based on previous work with natural products, the selected SL/FA ratios were 9 and 2.3 and the sulphate contents were 0, 1 and 5%. The water/binder ratio used for these cementitious mixes was 0.4. The specimens prepared for strength determination were prisms of 10 × 10 × 60 mm. The pastes were prepared and cured at 20 °C and 98% relative humidity for 1 day and then either stored at 20 °C at 98% humidity (dry) or immersed in distilled water (wet) for 14 and 28 days. The results showed that both FA and SL mixed with CS¯ produce ettringite after 28 days of setting, and this phase was the main crystalline hydrated product in all mixes. Calcium sulphate stimulates the hydration reactions of the mixes and the strength increases when the CS¯ content is higher due to ettringite formation, while the setting time decreases, as happened in the systems prepared with natural materials., Funding for this study was provided by the Agaur 2017 SGR 29 I+D+I project and the MICINN (Ministerio de Ciencia e Innovación) for supporting this research through the BIA 2016-76466R project. Special thanks to the Instituto de Ciencias de la Construcción “Eduardo Torroja”, where part of this work was developed. The corresponding author thanks the Miguel Casado Foundation for supporting his research career. The cement supplied by Ciments Molins is gratefully acknowledged., Peer Reviewed, Postprint (published version)