Skip to main content

Resultados relacionados

Resultados totales (Incluyendo duplicados): 14
Encontrada(s) 1 página(s)

Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Spectroscopic insight into the structural and microstructural properties of La2Ce2O7 ceramics

  • Sanjuán, María Luisa
  • Merino, Rosa Isabel
  • Lakshya, Annu Kumar
  • Chowdhury, Anirban
Ceria-based compounds with trivalent dopant ions are currently being investigated as electrolytes for solid oxide fuel cells operating at low to intermediate temperatures. In these materials, the dependence of the ionic conductivity on the dopant content, the relative cation size and the dopant/vacancy or vacancy/vacancy interactions are the subject of intense research, but there is scarce information about a possible correlation between these properties and microstructural ones, such as texture. Here, we address this question in the heavily doped fluorite-like La2Ce2O7 oxide, using a combination of X-ray diffraction, electron microscopy, optical absorption, Raman scattering and impedance spectroscopy. In all cases, materials with varying degree of 〈1 1 1〉 texture are compared with untextured samples. In this context, the most relevant Raman signatures are the fluorite-like mode at ∼448 cm−1 and a vacancy-related band at ∼578 cm−1. Although remarkable changes were observed upon varying the sintering temperature or the excitation wavelength, both textured and untextured materials displayed similar evolution. A selective enhancement of the vacancy-related band was observed upon decreasing the excitation wavelength from 647 to 488 nm, which is attributed to a resonance phenomenon involving vacancy-related electronic transitions. An indication of incipient vacancy ordering was given by the observation of an intense band at ∼346 cm−1, denoting C-R2O3-like short-range order; its enhancement with the annealing temperature is attributed to the growth of the C-like regions. Conductivity was measured in textured and untextured, fully dense pellets, in the former along and across the texture direction. Impedance plots suggest that the conductivity is dominated by oxide ions and do not allow to separate a grain boundary contribution in these materials with grain size around 1–2 μm. The conductivity amounts to around 10−5 S/cm at 650 K, with activation energy of 1.08–1.16 eV in the temperature range from around 470 to 870 K. Results were similar in textured and untextured materials. We conclude that there is no significant correlation between texture and vacancy concentration or vacancy ordering. A similar conclusion – no influence of texture – is reached concerning the electrical properties. Los compuestos a base de ceria dopada con iones trivalentes se están investigando como electrolitos para pilas de combustible de óxido sólido que funcionen a temperaturas bajas o intermedias. En estos materiales se ha estudiado profusamente la dependencia de la conductividad iónica con el contenido de dopante, el tamaño relativo de los cationes y las interacciones dopante/vacante o vacante/vacante, pero hay escasa información sobre la posible correlación entre estos factores y propiedades microestructurales como la textura. En este trabajo abordamos esta cuestión en la fluorita defectiva La2Ce2O7, utilizando para su caracterización difracción de rayos X, microscopía electrónica, absorción óptica, dispersión Raman y espectroscopia de impedancia. En cada caso se comparan materiales con distinto grado de textura a lo largo de las direcciones <111> y muestras sin textura. En este contexto, los indicadores más relevantes del espectro Raman son el modo de tipo fluorita en ∼448 cm-1 y una banda relacionada con las vacantes en ∼578 cm-1. Aunque se observaron cambios notables al variar la longitud de onda de excitación o la temperatura de sinterización, la evolución fue similar en materiales texturados y no texturados. La banda relacionada con las vacantes se intensifica al disminuir la longitud de onda de excitación de 647 a 488 nm, lo que se atribuye a un fenómeno de resonancia entre la energía de excitación y transiciones electrónicas asociadas a las vacantes. Por otra parte, la presencia de una banda en torno a 346 cm-1, típica de fases C-R2O3, sugiere que existe un cierto grado de ordenamiento de vacantes a corto alcance. El aumento de la banda con la temperatura de sinterización se atribuye al crecimiento de las regiones de tipo C. Se midió la conductividad eléctrica en cerámicas densas texturadas y no texturadas, en el primer caso paralela y perpendicularmente a la dirección de la textura. Los gráficos de impedancia sugieren que la conductividad se debe principalmente a iones de oxígeno y no permiten separar una contribución de las fronteras de grano en estos materiales con un tamaño de grano de alrededor de 1 a 2 μm. La conductividad es ∼10-5 S/cm a 650 K, con una energía de activación de 1,08 a 1,16 eV en el intervalo de temperaturas de ∼470 a 870 K. Se obtuvieron resultados similares en materiales texturados y no texturados. Se concluye que no existe una correlación significativa entre la textura y la concentración de vacantes o el ordenamiento de las mismas. Se llega a una conclusión similar en lo que se refiere a las propiedades eléctricas.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Ionic bent-core pillar[n]arenes: from liquid crystals to nanoaggregates and functional applications

  • Marín, Iván
  • Castillo-Vallés, Martín
  • Merino, Rosa I.
  • Folcia, César L.
  • Barberá, Joaquín
  • Ros, M. Blanca
  • Serrano, José L.
Herein, we report the first examples of supramolecular systems from bent-core-based pillar[n]arenes through ionic bonds. These ionic materials have been prepared by the interaction of an amino-ended pillar[5]arene (P5N10) and three different carboxylic acids, including bent-core moieties. The bent-core units are based on ester, biphenyl, and azobenzene structures bearing two different flexible spacers between the carboxyl group and the central bent-core aromatic units. The ionic pairs segregate the molecular blocks, leading to columnar liquid crystal organizations. These ionic supramolecular compounds exhibit interesting results as proton-conductive materials. Furthermore, the introduction of azobenzene units in the bent-core structure has provided a photoresponse to the proton conduction materials. Interestingly, the amphiphilic character generated by the ionic pairs and the hydrophobic bent-core structures allows their molecular self-assembly in water solution, resulting in aggregates of appealing morphologies. The structural modifications of the bent-core units (i.e., connecting bonds at the lateral structure and spacer lengths) provide an attractive analysis on the relationship between the chemical structure and the morphology of the aggregates (fibers, chiral ribbons, nanotubes...). Additionally, the self-assembly process and evolution of the aggregates from fibers to nanotubes have been studied with several techniques.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Phase segregation of aged MgCSZ–MgO directionally solidified eutectic composites

  • Oliete, Patricia B.
  • Merino, Rosa I.
  • Peña, Jose I.
  • Sanjuán, María Luisa
The improvement of the thermomechanical properties of Mg‐partially stabilized zirconia after appropriate thermal treatments is well known. Most studies in this subject have been conducted in polycrystalline materials produced by solid‐state reaction. In this work, we analyze the segregation behavior and mechanical properties of solidified eutectic composites of the ZrO2–MgO system, where MgO lamellae or fibers are embedded into a cubic Mg‐stabilized zirconia (MgCSZ) containing ∼18 mol% MgO. The eutectics have been aged at 1240 or 1225°C for periods varying between 2 and 24 h. This treatment results in the progressive phase separation of the MgCSZ matrix into different mixtures of tetragonal (t), monoclinic (m), δ (Mg2Zr5O12), and MgO phases. Two types of segregation are observed, according to whether the Mg‐rich phase is the metastable δ phase (type I) or MgO (type II). Both types may coexist in the same sample but type I predominates at 1240°C and type II at 1225°C. Type I is mainly of the t + δ type, although for long ageing time the t precipitates transform to monoclinic symmetry, resulting in a final m + δ segregation scheme. In type II segregation, the monoclinic phase is the main Mg‐poor product. Hardness and toughness have been studied by the Vickers indentation method. The indentation fracture toughness KIC increases progressively with ageing time and for 24 h treatment is more than doubled with respect to the as‐processed eutectic, while the hardness decreases slightly.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

High performance La2NiO4+δ oxygen and Ni–Ce0.9Gd0.1O2−δ fuel electrodes for thin film reversible solid oxide cells

  • Riaz, Adeel
  • Sirvent, Juande
  • Zueco-Vincelle, Juan
  • Buzi, Fjorelo
  • Panisset, Silvère
  • Stangl, Alexander
  • Rapenne, Laetitia
  • Baiutti, Federico
  • Mermoux, Michel
  • Laguna-Bercero, Miguel Angel
  • Tarancón, Albert
  • Burriel, Mónica
Thin film reversible solid oxide cells (TF-rSOCs) are attracting a great deal of interest as they promise to operate at much lower temperatures (400–600 °C) than state-of-the-art commercial fuel electrode-supported cells (600–800 °C). However, in all-ceramics TF-rSOCs the high polarization resistance of the electrodes limits the cell performance. To overcome this limitation, high performing oxygen and fuel electrodes were selected and their nanostructure was optimized. Thin nanoporous films of La2NiO4+δ were deposited as oxygen electrode by Pulsed Injection Metal Organic Chemical Vapor Deposition (PI-MOCVD) with different thickness. As for the fuel electrode, thin films of Ni–Ce0.9Gd0.1O2−δ (NiCGO) were deposited by Pulsed Laser Deposition (PLD) at various temperatures and pO2. The electrochemical activity of the oxygen and fuel electrodes was measured by Electrical Conductivity Relaxation (ECR) and Electrochemical Impedance Spectroscopy (EIS), respectively. The optimized electrodes were then deposited on a YSZ single crystal electrolyte and the cell was measured in fuel cell and electrolysis modes showing high performance with a power density of 70 mW cm−2 at 0.7 V and a current density of −44 mA cm−2 at 1.3 V at a low operating temperature of 600 °C. These results demonstrate the potential of using these materials as electrodes in TF-rSOCs.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Multifunctional polyoxomolybdate ionic liquid coatings for mitigating microbiologically influenced corrosion

  • Malefioudaki, Mariella
  • Misra, Archismita
  • Sbeity, Nadja
  • Zueco-Vincelle, Juan
  • Laguna-Bercero, Miguel A.
  • Koerdt, Andrea
  • Martín-Rapún, Rafael
  • Mitchell, Scott G.
Corrosion of metals and other materials in marine environments poses significant economic, operational, safety, and environmental challenges across the oil and gas industry, the renewable energy sector, and maritime infrastructure. Microbiologically influenced corrosion (MIC) accounts for a substantial portion of this corrosion, with sulfate-reducing bacteria (SRB) and methanogenic archaea (MA) being key contributors. Conventional methods such as cathodic polarization have proven insufficient in mitigating the colonization of corrosive microbial communities in real marine environments, requiring the development of alternative, broad-spectrum antimicrobial strategies to prevent such biofilm formation. Recently, molybdate has emerged as a potential alternative to traditional biocides and nitrate. Our hypothesis is polyoxometalate-ionic liquids (POM-ILs), which exhibit antimicrobial and anticorrosion properties, could have a broader spectrum of antimicrobial activity than demonstrated until now and could be capable of shielding and protecting sensitive metal surfaces from the extreme acidic environments produced by MIC microorganisms. Here we show how two prototype polyoxomolybdate-based POM-ILs, [(CH3(CH2)6)4N]2[Mo6O19] and [(CH3(CH2)6)4N]4[Mo8O26], demonstrated antimicrobial activity at microgram per millilitre concentrations, prevented biofilm formation on metal surfaces, and provided resistance to corrosive acidic environments. Furthermore, impedance measurements were commensurate with electron microscopy studies showing that POM-IL-coated brass coupons withstood extremely corrosive environments. These proof-of-concept results demonstrate how multi-functional POM-IL coatings represent promising MIC mitigation solutions by providing a hydrophobic acid-resistant and biocidal protective layer that prevents biocolonisation and acidic corrosion by MIC microorganisms.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Halogen-bonded ionic liquid crystals: supramolecular organization and ionic transport

  • Marcos, Mercedes
  • Concellón, Alberto
  • Terrel, Almudena
  • Merino, Rosa I.
  • Tejedor, Rosa M.
  • Barberá, Joaquín
  • Serrano, José L.
  • Uriel, Santiago
Ionic liquid crystals (ILCs) are emerging materials that combine the anisotropic self-assembly of liquid crystals with the ionic conductivity of ionic liquids, making them promising candidates for electrochemical applications such as ion-conducting membranes and next-generation electrolytes. In this work, we report the synthesis and characterization of a series of 1-alkyl-3-halopyridinium halides, where both the cationic and anionic components participate in halogen bonding, leading to enhanced mesophase stability and well-defined ionic nanochannels. Compounds with alkyl chains of 12 carbons or longer exhibit Smectic A liquid crystalline phases, with their stability increasing with chain length and halogen bond strength. X-ray diffraction analysis confirms the role of halogen bonding in driving molecular self-assembly and charge segregation, key factors in mesophase formation. Ionic conductivity measurements demonstrate that these ILCs facilitate ion transport through their nanosegregated ionic domains, with conductivities comparable to other liquid crystalline electrolytes. These findings highlight the potential of halogen-bonded ILCs as functional materials for electrochemical devices, providing a tunable platform for the development of advanced ion-conducting materials.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Praseodymium and gadolinium doped ceria as oxygen electrode for solid oxide cell applications

  • Morales-Zapata, Miguel Ángel
  • Larrea, Ángel
  • Laguna-Bercero, Miguel Ángel
his study analyzes the structural and electrochemical properties of praseodymium- and gadolinium-doped ceria (CPGO) samples formed by the sintering reaction of Pr2NiO4+δ (PNO) and Ce0.9Gd0.1O2−δ (GDC). X-ray powder diffraction analysis confirmed a single-phase cubic CPGO structure as a primary phase. The cationic compositions were determined using energy dispersive spectroscopy (EDS) in a scanning transmission electron microscope (STEM), while core-loss electron energy-loss spectroscopy (EELS) was used to determine the valence of Ce and Pr. The compatibility between thermal expansion coefficients validated their integration with electrolytes at the typical Solid Oxide Cell (SOC) operation temperatures. Oxygen chemical diffusion and surface exchange coefficients were investigated using the electrical conductivity relaxation (ECR) method at intervals of partial oxygen pressures between 0.10 and 0.21 atm and 600 °C and 800 °C. Finally, the samples were tested in symmetrical cells by electrochemical impedance spectroscopy (EIS) between 700 °C and 850 °C. A polarization resistance of 0.17 Ω cm2 at 850 °C was obtained for CPGO air electrodes formed by sintering a mixture of 80% by weight of GDC and 20% by weight of PNO. These findings confirm that PNO–GDC mixtures forming CPGO oxides are excellent candidates for SOC applications. En este estudio se analizan las propiedades estructurales y electroquímicas de composites formados por la reacción de sinterización de Pr2NiO4+δ (PNO) y Ce0.9Gd0.1O2-δ (GDC). Los refinamientos de Rietveld de los patrones de difracción de rayos X confirmaron una estructura cúbica monofásica de ceria dopada con praseodimio y gadolinio (CPGO) como fase primaria. Las composiciones catiónicas de CPGO se determinaron mediante espectroscopia de dispersión de energía (EDS) en un microscopio electrónico de transmisión de barrido (STEM), mientras que se utilizó espectroscopia de pérdida de energía de electrones (EELS) para determinar la valencia de Ce y Pr. La compatibilidad entre coeficientes de expansión térmica validó la integración de los electrodos con electrolitos a las temperaturas de operación típicas de las pilas de óxido sólido (SOC). Los coeficientes de difusión química de oxígeno y de intercambio superficial se determinaron mediante relajación de la conductividad eléctrica (ECR). Finalmente, se caracterizaron celdas simétricas mediante espectroscopia de impedancia electroquímica (EIS), obteniendo una baja resistencia de polarización de 0.17 Ω cm2 a 850 °C para electrodos de aire compuestos por 80% de GDC y 20% de PNO en peso. Estos hallazgos confirman que los electrodos de CPGO son excelentes candidatos para aplicaciones SOC.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Binary and ternary eutectic composites of the CaO – ZrO2 – MgO system for porous ceramic supports

  • Oliete, P.B.
  • Merino, R.I.
  • Peña, J.I.
  • Sanjuán, M.L.
We recently reported on the use of c-ZrO2-MgO eutectic composites produced by directional solidification as supports for CO2-selective membranes based on molten carbonates. Here, we explore other compositions, particularly within the CaO – ZrO2 – MgO system, with the ultimate goal of improving the membrane permeation by either increasing the support’s ionic conductivity or reducing its tortuosity. The three eutectic-like composites studied display MgO fibres embedded in single-phase or two-phase matrices. The composite with 8.5CaO/48.5ZrO2/43MgO mol% composition consists of MgO fibres in an oxide-ion conducting c-ZrO2 matrix containing both Ca and Mg. A binary CaZrO3 – MgO eutectic-like composite forms at ∼33CaO/35ZrO2/32MgO mol% with MgO fibres in a Ca-poor, Mg-doped CaZrO3 matrix displaying mixed oxide-ion and hole conductivity. For 22CaO/45ZrO2/33MgO mol% composition, a ternary eutectic forms with MgO fibres at the interfaces of CaZrO3 and c-ZrO2 phases. Acid etching tests were conducted to verify the feasibility of fabricating a porous support.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Polarization Dependence on the Optical Emission in Nd-Doped Bioactive W-TCP Coatings

  • Sola, Daniel
  • Chueca, Eloy
  • Peña, José Ignacio
Neodymium-doped bioactive wollastonite–tricalcium phosphate (W-TCP:Nd) coatings were fabricated by combining dip-coating and laser floating zone (LFZ) techniques to investigate the dependence of optical emission on polarization. Structural and spectroscopic analyses were performed on both longitudinal and transversal sections of the coating to assess the effects of directional solidification on luminescence and vibrational behavior. Micro-Raman spectroscopy revealed that the coating exhibited sharp, well-defined peaks compared to the W-TCP:Nd glass, confirming its glass-ceramic nature. New Raman modes appeared in the longitudinal section, accompanied by red and blue shifts in some bands relative to the transversal section, suggesting the presence of anisotropic stress and orientation-dependent crystal growth. Optical emission measurements showed that while the 4F3/2→4I11/2 transition near 1060 nm was nearly polarization independent, the 4F3/2→4I9/2 transition around 870–900 nm exhibited strong polarization dependence with notable Stark splitting. The relative intensity and spectral position of the Stark components varied systematically with the rotation of the emission polarization. These findings demonstrate that directional solidification induces polarization-dependent optical behavior, indicating potential applications for polarization-sensitive optical tracking and sensing in bioactive implant coatings.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Structural analysis of Pb-based organic–inorganic metal halide perovskites modified with Cetyltrimethylammonium bromide and 2-Aminopyrazine: Effects on stability and band gap

  • Tabares, Laurenth G.
  • Salamanca-Perdigón, Kevin
  • Lozano, Johan D.
  • Téllez, Jhoan F.
  • Laguna-Bercero, Miguel Á.
  • Macías, Mario A.
The synthesis of the hybrid organic–inorganic metal halide perovskites (C19H42N)3Pb2Cl7, (C19H42N)3Pb2Br7, (C4H7N3)2Cl2PbCl4, and (C4H7N3)2Br2PbBr4 is reported. These Pb-based structures were obtained using cetyltrimethylammonium bromide (CTAB) and 2-aminopyrazine (2-APZ) as organic precursors, respectively. Single-crystal X-ray diffraction analysis revealed that the asymmetric unit for CTAB-based compounds contains three [(C16H33)N(CH3)3]+ cations and a dinuclear [Pb2Cl7]3− unit composed of two lead-centered coordination polyhedra. In contrast, the 2-APZ-based compounds show [PbCl6]4− octahedra connected through vertex sharing to form layered structures alternating with organic [C4H7N3]2+ cations. In both cases, substitution of Cl by Br produced isostructural compounds, but changed the band gap values: from 3.6 eV to 3.3 eV for CTAB-based perovskites and from 2.5 eV to 2.1 eV for 2-APZ-based perovskites. Despite their lower band gap, the 2-APZ-derived compounds exhibited poor ambient stability. Conversely, CTAB-based compounds, although having a higher band gap, demonstrated enhanced thermal and environmental stability due to their hydrophobic nature. The different molecular sizes between 2-APZ and CTAB created different space between inorganic sheets leading to different quantum confinement. These findings highlight the potential for designing improved materials with both low band gap and high stability through mixed occupancy of different organic molecules.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Ion Transport in Supramolecular Ionic Liquid Crystals from Imidazolium Iodides and Hyperbranched Polyesters

  • Terrel, Almudena
  • Merino, Rosa I.
  • Serrano, José Luis
  • Concellón, Alberto
Polymeric liquid crystals (LCs) are attractive platforms for electrolyte design because their self-assembled nanostructures can generate organized ion-transport pathways while preserving the processability, thermal stability, and structural integrity required for next-generation electrochemical energy-conversion and storage devices. Herein, we report a synthetically simple and modular supramolecular strategy to transform commercially available hyperbranched bis-MPA polyester-64-OH (HBG4) into nanostructured ionic LC electrolytes by combining it with imidazolium iodide ionic liquids (ILs) bearing butyl, dodecyl, or perfluorinated chains. Hydrogen-bonding interactions between the terminal hydroxyl groups of the dendritic periphery and the imidazolium cations generate supramolecular ionic dendrimers in which distinct polar, dendritic, and apolar domains coexist within a single homogeneous polymeric material. In the bulk, cooperative nanosegregation of these domains drives self-assembly into robust smectic A LC phases over a broad compositional range, with mesophase stability strongly governed by the molecular architecture of the IL. Ionic conductivity measurements reveal clear composition–nanostructure–transport relationships, with conductivity modulated by IL content, temperature, mesophase stability, and the continuity of the polar ionic domains. In particular, perfluorinated ILs promote enhanced lamellar stability through fluorophilic segregation, whereas dodecyl-substituted ILs provide the best balance between high IL loading, LC order, and ionic transport. Overall, this work establishes hyperbranched polyesters as scalable supramolecular hosts for ILs and provides a practical route toward polymeric LC electrolytes with tunable nanostructure, ion-transport properties, and enhanced structural stability for electrochemical energy-conversion and storage applications.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

A detailed processing route and electrochemical validation of fuel-electrode supported planar solid oxide cells toward scalable manufacturing

  • Zueco-Vincelle, Juan
  • Campos-Galera, Andrés
  • Alconchel-Allué, Aida
  • de la Torre-Gamarra, Carmen
  • Larrea, Ángel
  • Orera, Alodia
  • Laguna-Bercero, Miguel Ángel
Planar fuel electrode supported 5 cm × 5 cm solid oxide cells (SOCs) were manufactured by conventional methods such as tape-casting, lamination and screen printing. The chosen materials were a Ni–8% mol Y2O3-stabilized ZrO2 (Ni-YSZ) cermet as fuel electrode, YSZ as electrolyte and lanthanum strontium manganite (LSM)-YSZ or lanthanum strontium cobalt ferrite (LSCF)-gadolinium-doped ceria (GDC) composites as air electrode, including in this later case a GDC barrier layer. Electrochemical characterization and scanning electron microscopy (SEM) analysis validated the proposed manufacturing methods and allowed a comparison of SOCs performances at several gas concentrations and temperatures. As a reference, EIS measurements at 750 °C with 100% O2 and 50% H2O resulted in polarization resistances of 0.24 Ω cm2 for the LSCF-GDC cell and 0.60 Ω cm2 for the LSM-YSZ cell, while the achieved current densities at 1.3 V were 0.56 and 0.40 A/cm2, respectively. Se fabricaron celdas de óxido sólido (SOCs) planas de 5 × 5 cm2 soportadas sobre el electrodo de combustible mediante métodos convencionales como colado en cinta, laminación y serigrafía. Los materiales seleccionados fueron un cermet de Ni–ZrO2 estabilizada con un 8% molar de Y2O3 (Ni-YSZ) como electrodo de combustible, YSZ como electrolito y compuestos de manganita de lantano y estroncio (LSM)-YSZ o ferrita cobaltita de lantano y estroncio (LSCF)-ceria dopada con gadolinio (GDC) como electrodo de aire, incluyendo en este último caso una capa barrera de GDC. La caracterización electroquímica y el análisis mediante microscopía electrónica de barrido (SEM) validaron los métodos de fabricación propuestos y permitieron comparar el rendimiento de las SOCs a diferentes concentraciones de gas y temperaturas. Como referencia, las medidas de espectroscopía de impedancia electroquímica (EIS) a 750 °C con 100% O2 y 50% H2O proporcionaron resistencias de polarización de 0.24 Ω cm2 para la celda LSCF-GDC y de 0.60 Ω cm2 para la celda LSM-YSZ, mientras que las densidades de corriente alcanzadas a 1.3 V fueron de 0.56 y 0.40 A/cm2, respectivamente.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Current trends in solid state ionics: Solid oxide cells a proceedings-perspective paper of the E-MRS 2025 spring meeting (symposium K: “Solid state ionics: Functional materials and devices for electrochemical energy conversion and storage applications”)

  • Burriel, Mónica
  • Tarancon, Albert
  • Laguna-Bercero, Miguel A.
With this series of proceedings-perspective articles, the journal Solid State Ionics introduces a novel format of progress reports from the research community that aims to bridge the gap between traditional conference proceedings and perspective articles. In addition, it has become apparent in recent years that traditional conference proceedings papers (presumably also favoured by a significant acceleration in scientific publishing) no longer meet the response that was the case in earlier times. This new paper format is an attempt to meet the needs of researchers in a modern publication environment to report the latest developments at the forefront of science (as they are usually discussed at conferences), which are thus brought into a citable form as soon as possible. We thus believe that this innovative format offers several advantages: It accelerates the dissemination of cutting-edge research, provides strategic guidance on promising research directions, increases the visibility of key conference papers, delivers efficiently curated content to readers, and provides a good balance between timely coverage and scientific depth. The E-MRS 2025 Spring Meeting Symposium K on “Solid state ionics: functional materials and devices for electrochemical energy conversion and storage applications” serves as the first conference where the Solid State Ionics community is exploring this innovative publication approach. Rather than providing exhaustive coverage of all presentations, this new format of proceedings-perspective papers highlights key developments and emerging research directions within the field of solid state ionics as identified by leading contributors in each subfield. Each paper focuses on one of the following four central topics. Defect Engineering & Surface Chemistry. Solid Oxide Cells. Protonics & Reactors. Batteries.
Zaguán. Repositorio Digital de la Universidad de Zaragoza
Publication Artículo científico (JournalArticle)

Competitive solid oxide cells using YSr2Cu2FeO7+δ based oxygen electrodes prepared by combustion synthesis

  • Zueco-Vincelle, Juan
  • Marín-Gamero, Rafael
  • de la Torre-Gamarra, Carmen
  • Orera, Alodia
  • García-Alvarado, Flaviano
  • García-Martín, Susana
  • Laguna-Bercero, Miguel A.
In this paper we present the electrochemical performance of YSr2Cu2FeO7+δ (YSCF). YSCF was prepared by the combustion method and showed YBaCuO-type structure. Symmetrical cells with YSCF-Ce0.9Gd0.1O2-δ (CGO) electrodes showed a polarization resistance of 0.3 Ω cm2 at 600 °C. Then, YSCF was incorporated in fuel electrode supported solid oxide cells (SOCs). SOCs were composed by the Ni-8% mol stabilized ZrO2 (YSZ) cermet as fuel electrode, YSZ as electrolyte, CGO as barrier layer and the composite YSCF-CGO as oxygen electrode. A SOC with (La0.6Sr0.4)0.95Fe0.8Co0.2O3−δ (LSCF)-CGO oxygen electrode was also fabricated as reference cell. At 800 °C under 50:50% H2O:H2 in the fuel electrode and air in the oxygen electrode, YSCF-based cell reached a maximum power output of 0.74 W cm−2 at 0.5 V in SOFC mode and −1.1 A cm−2 at thermoneutral voltage (1.3 V) in SOEC mode. In the same conditions, EIS measurements revealed a polarization resistance of 0.17 Ω cm2.